1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright(c) 1999 - 2006 Intel Corporation. */
5 #include <net/ip6_checksum.h>
7 #include <linux/prefetch.h>
8 #include <linux/bitops.h>
9 #include <linux/if_vlan.h>
11 char e1000_driver_name[] = "e1000";
12 static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
13 #define DRV_VERSION "7.3.21-k8-NAPI"
14 const char e1000_driver_version[] = DRV_VERSION;
15 static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
17 /* e1000_pci_tbl - PCI Device ID Table
19 * Last entry must be all 0s
22 * {PCI_DEVICE(PCI_VENDOR_ID_INTEL, device_id)}
24 static const struct pci_device_id e1000_pci_tbl[] = {
25 INTEL_E1000_ETHERNET_DEVICE(0x1000),
26 INTEL_E1000_ETHERNET_DEVICE(0x1001),
27 INTEL_E1000_ETHERNET_DEVICE(0x1004),
28 INTEL_E1000_ETHERNET_DEVICE(0x1008),
29 INTEL_E1000_ETHERNET_DEVICE(0x1009),
30 INTEL_E1000_ETHERNET_DEVICE(0x100C),
31 INTEL_E1000_ETHERNET_DEVICE(0x100D),
32 INTEL_E1000_ETHERNET_DEVICE(0x100E),
33 INTEL_E1000_ETHERNET_DEVICE(0x100F),
34 INTEL_E1000_ETHERNET_DEVICE(0x1010),
35 INTEL_E1000_ETHERNET_DEVICE(0x1011),
36 INTEL_E1000_ETHERNET_DEVICE(0x1012),
37 INTEL_E1000_ETHERNET_DEVICE(0x1013),
38 INTEL_E1000_ETHERNET_DEVICE(0x1014),
39 INTEL_E1000_ETHERNET_DEVICE(0x1015),
40 INTEL_E1000_ETHERNET_DEVICE(0x1016),
41 INTEL_E1000_ETHERNET_DEVICE(0x1017),
42 INTEL_E1000_ETHERNET_DEVICE(0x1018),
43 INTEL_E1000_ETHERNET_DEVICE(0x1019),
44 INTEL_E1000_ETHERNET_DEVICE(0x101A),
45 INTEL_E1000_ETHERNET_DEVICE(0x101D),
46 INTEL_E1000_ETHERNET_DEVICE(0x101E),
47 INTEL_E1000_ETHERNET_DEVICE(0x1026),
48 INTEL_E1000_ETHERNET_DEVICE(0x1027),
49 INTEL_E1000_ETHERNET_DEVICE(0x1028),
50 INTEL_E1000_ETHERNET_DEVICE(0x1075),
51 INTEL_E1000_ETHERNET_DEVICE(0x1076),
52 INTEL_E1000_ETHERNET_DEVICE(0x1077),
53 INTEL_E1000_ETHERNET_DEVICE(0x1078),
54 INTEL_E1000_ETHERNET_DEVICE(0x1079),
55 INTEL_E1000_ETHERNET_DEVICE(0x107A),
56 INTEL_E1000_ETHERNET_DEVICE(0x107B),
57 INTEL_E1000_ETHERNET_DEVICE(0x107C),
58 INTEL_E1000_ETHERNET_DEVICE(0x108A),
59 INTEL_E1000_ETHERNET_DEVICE(0x1099),
60 INTEL_E1000_ETHERNET_DEVICE(0x10B5),
61 INTEL_E1000_ETHERNET_DEVICE(0x2E6E),
62 /* required last entry */
66 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
68 int e1000_up(struct e1000_adapter *adapter);
69 void e1000_down(struct e1000_adapter *adapter);
70 void e1000_reinit_locked(struct e1000_adapter *adapter);
71 void e1000_reset(struct e1000_adapter *adapter);
72 int e1000_setup_all_tx_resources(struct e1000_adapter *adapter);
73 int e1000_setup_all_rx_resources(struct e1000_adapter *adapter);
74 void e1000_free_all_tx_resources(struct e1000_adapter *adapter);
75 void e1000_free_all_rx_resources(struct e1000_adapter *adapter);
76 static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
77 struct e1000_tx_ring *txdr);
78 static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
79 struct e1000_rx_ring *rxdr);
80 static void e1000_free_tx_resources(struct e1000_adapter *adapter,
81 struct e1000_tx_ring *tx_ring);
82 static void e1000_free_rx_resources(struct e1000_adapter *adapter,
83 struct e1000_rx_ring *rx_ring);
84 void e1000_update_stats(struct e1000_adapter *adapter);
86 static int e1000_init_module(void);
87 static void e1000_exit_module(void);
88 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent);
89 static void e1000_remove(struct pci_dev *pdev);
90 static int e1000_alloc_queues(struct e1000_adapter *adapter);
91 static int e1000_sw_init(struct e1000_adapter *adapter);
92 int e1000_open(struct net_device *netdev);
93 int e1000_close(struct net_device *netdev);
94 static void e1000_configure_tx(struct e1000_adapter *adapter);
95 static void e1000_configure_rx(struct e1000_adapter *adapter);
96 static void e1000_setup_rctl(struct e1000_adapter *adapter);
97 static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter);
98 static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter);
99 static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
100 struct e1000_tx_ring *tx_ring);
101 static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
102 struct e1000_rx_ring *rx_ring);
103 static void e1000_set_rx_mode(struct net_device *netdev);
104 static void e1000_update_phy_info_task(struct work_struct *work);
105 static void e1000_watchdog(struct work_struct *work);
106 static void e1000_82547_tx_fifo_stall_task(struct work_struct *work);
107 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
108 struct net_device *netdev);
109 static int e1000_change_mtu(struct net_device *netdev, int new_mtu);
110 static int e1000_set_mac(struct net_device *netdev, void *p);
111 static irqreturn_t e1000_intr(int irq, void *data);
112 static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
113 struct e1000_tx_ring *tx_ring);
114 static int e1000_clean(struct napi_struct *napi, int budget);
115 static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
116 struct e1000_rx_ring *rx_ring,
117 int *work_done, int work_to_do);
118 static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
119 struct e1000_rx_ring *rx_ring,
120 int *work_done, int work_to_do);
121 static void e1000_alloc_dummy_rx_buffers(struct e1000_adapter *adapter,
122 struct e1000_rx_ring *rx_ring,
126 static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
127 struct e1000_rx_ring *rx_ring,
129 static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
130 struct e1000_rx_ring *rx_ring,
132 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd);
133 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
135 static void e1000_enter_82542_rst(struct e1000_adapter *adapter);
136 static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
137 static void e1000_tx_timeout(struct net_device *dev);
138 static void e1000_reset_task(struct work_struct *work);
139 static void e1000_smartspeed(struct e1000_adapter *adapter);
140 static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
141 struct sk_buff *skb);
143 static bool e1000_vlan_used(struct e1000_adapter *adapter);
144 static void e1000_vlan_mode(struct net_device *netdev,
145 netdev_features_t features);
146 static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter,
148 static int e1000_vlan_rx_add_vid(struct net_device *netdev,
149 __be16 proto, u16 vid);
150 static int e1000_vlan_rx_kill_vid(struct net_device *netdev,
151 __be16 proto, u16 vid);
152 static void e1000_restore_vlan(struct e1000_adapter *adapter);
155 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
156 static int e1000_resume(struct pci_dev *pdev);
158 static void e1000_shutdown(struct pci_dev *pdev);
160 #ifdef CONFIG_NET_POLL_CONTROLLER
161 /* for netdump / net console */
162 static void e1000_netpoll (struct net_device *netdev);
165 #define COPYBREAK_DEFAULT 256
166 static unsigned int copybreak __read_mostly = COPYBREAK_DEFAULT;
167 module_param(copybreak, uint, 0644);
168 MODULE_PARM_DESC(copybreak,
169 "Maximum size of packet that is copied to a new buffer on receive");
171 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
172 pci_channel_state_t state);
173 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev);
174 static void e1000_io_resume(struct pci_dev *pdev);
176 static const struct pci_error_handlers e1000_err_handler = {
177 .error_detected = e1000_io_error_detected,
178 .slot_reset = e1000_io_slot_reset,
179 .resume = e1000_io_resume,
182 static struct pci_driver e1000_driver = {
183 .name = e1000_driver_name,
184 .id_table = e1000_pci_tbl,
185 .probe = e1000_probe,
186 .remove = e1000_remove,
188 /* Power Management Hooks */
189 .suspend = e1000_suspend,
190 .resume = e1000_resume,
192 .shutdown = e1000_shutdown,
193 .err_handler = &e1000_err_handler
196 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
197 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
198 MODULE_LICENSE("GPL v2");
199 MODULE_VERSION(DRV_VERSION);
201 #define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK)
202 static int debug = -1;
203 module_param(debug, int, 0);
204 MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)");
207 * e1000_get_hw_dev - return device
208 * used by hardware layer to print debugging information
211 struct net_device *e1000_get_hw_dev(struct e1000_hw *hw)
213 struct e1000_adapter *adapter = hw->back;
214 return adapter->netdev;
218 * e1000_init_module - Driver Registration Routine
220 * e1000_init_module is the first routine called when the driver is
221 * loaded. All it does is register with the PCI subsystem.
223 static int __init e1000_init_module(void)
226 pr_info("%s - version %s\n", e1000_driver_string, e1000_driver_version);
228 pr_info("%s\n", e1000_copyright);
230 ret = pci_register_driver(&e1000_driver);
231 if (copybreak != COPYBREAK_DEFAULT) {
233 pr_info("copybreak disabled\n");
235 pr_info("copybreak enabled for "
236 "packets <= %u bytes\n", copybreak);
241 module_init(e1000_init_module);
244 * e1000_exit_module - Driver Exit Cleanup Routine
246 * e1000_exit_module is called just before the driver is removed
249 static void __exit e1000_exit_module(void)
251 pci_unregister_driver(&e1000_driver);
254 module_exit(e1000_exit_module);
256 static int e1000_request_irq(struct e1000_adapter *adapter)
258 struct net_device *netdev = adapter->netdev;
259 irq_handler_t handler = e1000_intr;
260 int irq_flags = IRQF_SHARED;
263 err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
266 e_err(probe, "Unable to allocate interrupt Error: %d\n", err);
272 static void e1000_free_irq(struct e1000_adapter *adapter)
274 struct net_device *netdev = adapter->netdev;
276 free_irq(adapter->pdev->irq, netdev);
280 * e1000_irq_disable - Mask off interrupt generation on the NIC
281 * @adapter: board private structure
283 static void e1000_irq_disable(struct e1000_adapter *adapter)
285 struct e1000_hw *hw = &adapter->hw;
289 synchronize_irq(adapter->pdev->irq);
293 * e1000_irq_enable - Enable default interrupt generation settings
294 * @adapter: board private structure
296 static void e1000_irq_enable(struct e1000_adapter *adapter)
298 struct e1000_hw *hw = &adapter->hw;
300 ew32(IMS, IMS_ENABLE_MASK);
304 static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
306 struct e1000_hw *hw = &adapter->hw;
307 struct net_device *netdev = adapter->netdev;
308 u16 vid = hw->mng_cookie.vlan_id;
309 u16 old_vid = adapter->mng_vlan_id;
311 if (!e1000_vlan_used(adapter))
314 if (!test_bit(vid, adapter->active_vlans)) {
315 if (hw->mng_cookie.status &
316 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) {
317 e1000_vlan_rx_add_vid(netdev, htons(ETH_P_8021Q), vid);
318 adapter->mng_vlan_id = vid;
320 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
322 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
324 !test_bit(old_vid, adapter->active_vlans))
325 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q),
328 adapter->mng_vlan_id = vid;
332 static void e1000_init_manageability(struct e1000_adapter *adapter)
334 struct e1000_hw *hw = &adapter->hw;
336 if (adapter->en_mng_pt) {
337 u32 manc = er32(MANC);
339 /* disable hardware interception of ARP */
340 manc &= ~(E1000_MANC_ARP_EN);
346 static void e1000_release_manageability(struct e1000_adapter *adapter)
348 struct e1000_hw *hw = &adapter->hw;
350 if (adapter->en_mng_pt) {
351 u32 manc = er32(MANC);
353 /* re-enable hardware interception of ARP */
354 manc |= E1000_MANC_ARP_EN;
361 * e1000_configure - configure the hardware for RX and TX
362 * @adapter = private board structure
364 static void e1000_configure(struct e1000_adapter *adapter)
366 struct net_device *netdev = adapter->netdev;
369 e1000_set_rx_mode(netdev);
371 e1000_restore_vlan(adapter);
372 e1000_init_manageability(adapter);
374 e1000_configure_tx(adapter);
375 e1000_setup_rctl(adapter);
376 e1000_configure_rx(adapter);
377 /* call E1000_DESC_UNUSED which always leaves
378 * at least 1 descriptor unused to make sure
379 * next_to_use != next_to_clean
381 for (i = 0; i < adapter->num_rx_queues; i++) {
382 struct e1000_rx_ring *ring = &adapter->rx_ring[i];
383 adapter->alloc_rx_buf(adapter, ring,
384 E1000_DESC_UNUSED(ring));
388 int e1000_up(struct e1000_adapter *adapter)
390 struct e1000_hw *hw = &adapter->hw;
392 /* hardware has been reset, we need to reload some things */
393 e1000_configure(adapter);
395 clear_bit(__E1000_DOWN, &adapter->flags);
397 napi_enable(&adapter->napi);
399 e1000_irq_enable(adapter);
401 netif_wake_queue(adapter->netdev);
403 /* fire a link change interrupt to start the watchdog */
404 ew32(ICS, E1000_ICS_LSC);
409 * e1000_power_up_phy - restore link in case the phy was powered down
410 * @adapter: address of board private structure
412 * The phy may be powered down to save power and turn off link when the
413 * driver is unloaded and wake on lan is not enabled (among others)
414 * *** this routine MUST be followed by a call to e1000_reset ***
416 void e1000_power_up_phy(struct e1000_adapter *adapter)
418 struct e1000_hw *hw = &adapter->hw;
421 /* Just clear the power down bit to wake the phy back up */
422 if (hw->media_type == e1000_media_type_copper) {
423 /* according to the manual, the phy will retain its
424 * settings across a power-down/up cycle
426 e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
427 mii_reg &= ~MII_CR_POWER_DOWN;
428 e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
432 static void e1000_power_down_phy(struct e1000_adapter *adapter)
434 struct e1000_hw *hw = &adapter->hw;
436 /* Power down the PHY so no link is implied when interface is down *
437 * The PHY cannot be powered down if any of the following is true *
440 * (c) SoL/IDER session is active
442 if (!adapter->wol && hw->mac_type >= e1000_82540 &&
443 hw->media_type == e1000_media_type_copper) {
446 switch (hw->mac_type) {
449 case e1000_82545_rev_3:
452 case e1000_82546_rev_3:
454 case e1000_82541_rev_2:
456 case e1000_82547_rev_2:
457 if (er32(MANC) & E1000_MANC_SMBUS_EN)
463 e1000_read_phy_reg(hw, PHY_CTRL, &mii_reg);
464 mii_reg |= MII_CR_POWER_DOWN;
465 e1000_write_phy_reg(hw, PHY_CTRL, mii_reg);
472 static void e1000_down_and_stop(struct e1000_adapter *adapter)
474 set_bit(__E1000_DOWN, &adapter->flags);
476 cancel_delayed_work_sync(&adapter->watchdog_task);
479 * Since the watchdog task can reschedule other tasks, we should cancel
480 * it first, otherwise we can run into the situation when a work is
481 * still running after the adapter has been turned down.
484 cancel_delayed_work_sync(&adapter->phy_info_task);
485 cancel_delayed_work_sync(&adapter->fifo_stall_task);
487 /* Only kill reset task if adapter is not resetting */
488 if (!test_bit(__E1000_RESETTING, &adapter->flags))
489 cancel_work_sync(&adapter->reset_task);
492 void e1000_down(struct e1000_adapter *adapter)
494 struct e1000_hw *hw = &adapter->hw;
495 struct net_device *netdev = adapter->netdev;
498 /* disable receives in the hardware */
500 ew32(RCTL, rctl & ~E1000_RCTL_EN);
501 /* flush and sleep below */
503 netif_tx_disable(netdev);
505 /* disable transmits in the hardware */
507 tctl &= ~E1000_TCTL_EN;
509 /* flush both disables and wait for them to finish */
513 /* Set the carrier off after transmits have been disabled in the
514 * hardware, to avoid race conditions with e1000_watchdog() (which
515 * may be running concurrently to us, checking for the carrier
516 * bit to decide whether it should enable transmits again). Such
517 * a race condition would result into transmission being disabled
518 * in the hardware until the next IFF_DOWN+IFF_UP cycle.
520 netif_carrier_off(netdev);
522 napi_disable(&adapter->napi);
524 e1000_irq_disable(adapter);
526 /* Setting DOWN must be after irq_disable to prevent
527 * a screaming interrupt. Setting DOWN also prevents
528 * tasks from rescheduling.
530 e1000_down_and_stop(adapter);
532 adapter->link_speed = 0;
533 adapter->link_duplex = 0;
535 e1000_reset(adapter);
536 e1000_clean_all_tx_rings(adapter);
537 e1000_clean_all_rx_rings(adapter);
540 void e1000_reinit_locked(struct e1000_adapter *adapter)
542 WARN_ON(in_interrupt());
543 while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
547 clear_bit(__E1000_RESETTING, &adapter->flags);
550 void e1000_reset(struct e1000_adapter *adapter)
552 struct e1000_hw *hw = &adapter->hw;
553 u32 pba = 0, tx_space, min_tx_space, min_rx_space;
554 bool legacy_pba_adjust = false;
557 /* Repartition Pba for greater than 9k mtu
558 * To take effect CTRL.RST is required.
561 switch (hw->mac_type) {
562 case e1000_82542_rev2_0:
563 case e1000_82542_rev2_1:
568 case e1000_82541_rev_2:
569 legacy_pba_adjust = true;
573 case e1000_82545_rev_3:
576 case e1000_82546_rev_3:
580 case e1000_82547_rev_2:
581 legacy_pba_adjust = true;
584 case e1000_undefined:
589 if (legacy_pba_adjust) {
590 if (hw->max_frame_size > E1000_RXBUFFER_8192)
591 pba -= 8; /* allocate more FIFO for Tx */
593 if (hw->mac_type == e1000_82547) {
594 adapter->tx_fifo_head = 0;
595 adapter->tx_head_addr = pba << E1000_TX_HEAD_ADDR_SHIFT;
596 adapter->tx_fifo_size =
597 (E1000_PBA_40K - pba) << E1000_PBA_BYTES_SHIFT;
598 atomic_set(&adapter->tx_fifo_stall, 0);
600 } else if (hw->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
601 /* adjust PBA for jumbo frames */
604 /* To maintain wire speed transmits, the Tx FIFO should be
605 * large enough to accommodate two full transmit packets,
606 * rounded up to the next 1KB and expressed in KB. Likewise,
607 * the Rx FIFO should be large enough to accommodate at least
608 * one full receive packet and is similarly rounded up and
612 /* upper 16 bits has Tx packet buffer allocation size in KB */
613 tx_space = pba >> 16;
614 /* lower 16 bits has Rx packet buffer allocation size in KB */
616 /* the Tx fifo also stores 16 bytes of information about the Tx
617 * but don't include ethernet FCS because hardware appends it
619 min_tx_space = (hw->max_frame_size +
620 sizeof(struct e1000_tx_desc) -
622 min_tx_space = ALIGN(min_tx_space, 1024);
624 /* software strips receive CRC, so leave room for it */
625 min_rx_space = hw->max_frame_size;
626 min_rx_space = ALIGN(min_rx_space, 1024);
629 /* If current Tx allocation is less than the min Tx FIFO size,
630 * and the min Tx FIFO size is less than the current Rx FIFO
631 * allocation, take space away from current Rx allocation
633 if (tx_space < min_tx_space &&
634 ((min_tx_space - tx_space) < pba)) {
635 pba = pba - (min_tx_space - tx_space);
637 /* PCI/PCIx hardware has PBA alignment constraints */
638 switch (hw->mac_type) {
639 case e1000_82545 ... e1000_82546_rev_3:
640 pba &= ~(E1000_PBA_8K - 1);
646 /* if short on Rx space, Rx wins and must trump Tx
647 * adjustment or use Early Receive if available
649 if (pba < min_rx_space)
656 /* flow control settings:
657 * The high water mark must be low enough to fit one full frame
658 * (or the size used for early receive) above it in the Rx FIFO.
659 * Set it to the lower of:
660 * - 90% of the Rx FIFO size, and
661 * - the full Rx FIFO size minus the early receive size (for parts
662 * with ERT support assuming ERT set to E1000_ERT_2048), or
663 * - the full Rx FIFO size minus one full frame
665 hwm = min(((pba << 10) * 9 / 10),
666 ((pba << 10) - hw->max_frame_size));
668 hw->fc_high_water = hwm & 0xFFF8; /* 8-byte granularity */
669 hw->fc_low_water = hw->fc_high_water - 8;
670 hw->fc_pause_time = E1000_FC_PAUSE_TIME;
672 hw->fc = hw->original_fc;
674 /* Allow time for pending master requests to run */
676 if (hw->mac_type >= e1000_82544)
679 if (e1000_init_hw(hw))
680 e_dev_err("Hardware Error\n");
681 e1000_update_mng_vlan(adapter);
683 /* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */
684 if (hw->mac_type >= e1000_82544 &&
686 hw->autoneg_advertised == ADVERTISE_1000_FULL) {
687 u32 ctrl = er32(CTRL);
688 /* clear phy power management bit if we are in gig only mode,
689 * which if enabled will attempt negotiation to 100Mb, which
690 * can cause a loss of link at power off or driver unload
692 ctrl &= ~E1000_CTRL_SWDPIN3;
696 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
697 ew32(VET, ETHERNET_IEEE_VLAN_TYPE);
699 e1000_reset_adaptive(hw);
700 e1000_phy_get_info(hw, &adapter->phy_info);
702 e1000_release_manageability(adapter);
705 /* Dump the eeprom for users having checksum issues */
706 static void e1000_dump_eeprom(struct e1000_adapter *adapter)
708 struct net_device *netdev = adapter->netdev;
709 struct ethtool_eeprom eeprom;
710 const struct ethtool_ops *ops = netdev->ethtool_ops;
713 u16 csum_old, csum_new = 0;
715 eeprom.len = ops->get_eeprom_len(netdev);
718 data = kmalloc(eeprom.len, GFP_KERNEL);
722 ops->get_eeprom(netdev, &eeprom, data);
724 csum_old = (data[EEPROM_CHECKSUM_REG * 2]) +
725 (data[EEPROM_CHECKSUM_REG * 2 + 1] << 8);
726 for (i = 0; i < EEPROM_CHECKSUM_REG * 2; i += 2)
727 csum_new += data[i] + (data[i + 1] << 8);
728 csum_new = EEPROM_SUM - csum_new;
730 pr_err("/*********************/\n");
731 pr_err("Current EEPROM Checksum : 0x%04x\n", csum_old);
732 pr_err("Calculated : 0x%04x\n", csum_new);
734 pr_err("Offset Values\n");
735 pr_err("======== ======\n");
736 print_hex_dump(KERN_ERR, "", DUMP_PREFIX_OFFSET, 16, 1, data, 128, 0);
738 pr_err("Include this output when contacting your support provider.\n");
739 pr_err("This is not a software error! Something bad happened to\n");
740 pr_err("your hardware or EEPROM image. Ignoring this problem could\n");
741 pr_err("result in further problems, possibly loss of data,\n");
742 pr_err("corruption or system hangs!\n");
743 pr_err("The MAC Address will be reset to 00:00:00:00:00:00,\n");
744 pr_err("which is invalid and requires you to set the proper MAC\n");
745 pr_err("address manually before continuing to enable this network\n");
746 pr_err("device. Please inspect the EEPROM dump and report the\n");
747 pr_err("issue to your hardware vendor or Intel Customer Support.\n");
748 pr_err("/*********************/\n");
754 * e1000_is_need_ioport - determine if an adapter needs ioport resources or not
755 * @pdev: PCI device information struct
757 * Return true if an adapter needs ioport resources
759 static int e1000_is_need_ioport(struct pci_dev *pdev)
761 switch (pdev->device) {
762 case E1000_DEV_ID_82540EM:
763 case E1000_DEV_ID_82540EM_LOM:
764 case E1000_DEV_ID_82540EP:
765 case E1000_DEV_ID_82540EP_LOM:
766 case E1000_DEV_ID_82540EP_LP:
767 case E1000_DEV_ID_82541EI:
768 case E1000_DEV_ID_82541EI_MOBILE:
769 case E1000_DEV_ID_82541ER:
770 case E1000_DEV_ID_82541ER_LOM:
771 case E1000_DEV_ID_82541GI:
772 case E1000_DEV_ID_82541GI_LF:
773 case E1000_DEV_ID_82541GI_MOBILE:
774 case E1000_DEV_ID_82544EI_COPPER:
775 case E1000_DEV_ID_82544EI_FIBER:
776 case E1000_DEV_ID_82544GC_COPPER:
777 case E1000_DEV_ID_82544GC_LOM:
778 case E1000_DEV_ID_82545EM_COPPER:
779 case E1000_DEV_ID_82545EM_FIBER:
780 case E1000_DEV_ID_82546EB_COPPER:
781 case E1000_DEV_ID_82546EB_FIBER:
782 case E1000_DEV_ID_82546EB_QUAD_COPPER:
789 static netdev_features_t e1000_fix_features(struct net_device *netdev,
790 netdev_features_t features)
792 /* Since there is no support for separate Rx/Tx vlan accel
793 * enable/disable make sure Tx flag is always in same state as Rx.
795 if (features & NETIF_F_HW_VLAN_CTAG_RX)
796 features |= NETIF_F_HW_VLAN_CTAG_TX;
798 features &= ~NETIF_F_HW_VLAN_CTAG_TX;
803 static int e1000_set_features(struct net_device *netdev,
804 netdev_features_t features)
806 struct e1000_adapter *adapter = netdev_priv(netdev);
807 netdev_features_t changed = features ^ netdev->features;
809 if (changed & NETIF_F_HW_VLAN_CTAG_RX)
810 e1000_vlan_mode(netdev, features);
812 if (!(changed & (NETIF_F_RXCSUM | NETIF_F_RXALL)))
815 netdev->features = features;
816 adapter->rx_csum = !!(features & NETIF_F_RXCSUM);
818 if (netif_running(netdev))
819 e1000_reinit_locked(adapter);
821 e1000_reset(adapter);
826 static const struct net_device_ops e1000_netdev_ops = {
827 .ndo_open = e1000_open,
828 .ndo_stop = e1000_close,
829 .ndo_start_xmit = e1000_xmit_frame,
830 .ndo_set_rx_mode = e1000_set_rx_mode,
831 .ndo_set_mac_address = e1000_set_mac,
832 .ndo_tx_timeout = e1000_tx_timeout,
833 .ndo_change_mtu = e1000_change_mtu,
834 .ndo_do_ioctl = e1000_ioctl,
835 .ndo_validate_addr = eth_validate_addr,
836 .ndo_vlan_rx_add_vid = e1000_vlan_rx_add_vid,
837 .ndo_vlan_rx_kill_vid = e1000_vlan_rx_kill_vid,
838 #ifdef CONFIG_NET_POLL_CONTROLLER
839 .ndo_poll_controller = e1000_netpoll,
841 .ndo_fix_features = e1000_fix_features,
842 .ndo_set_features = e1000_set_features,
846 * e1000_init_hw_struct - initialize members of hw struct
847 * @adapter: board private struct
848 * @hw: structure used by e1000_hw.c
850 * Factors out initialization of the e1000_hw struct to its own function
851 * that can be called very early at init (just after struct allocation).
852 * Fields are initialized based on PCI device information and
853 * OS network device settings (MTU size).
854 * Returns negative error codes if MAC type setup fails.
856 static int e1000_init_hw_struct(struct e1000_adapter *adapter,
859 struct pci_dev *pdev = adapter->pdev;
861 /* PCI config space info */
862 hw->vendor_id = pdev->vendor;
863 hw->device_id = pdev->device;
864 hw->subsystem_vendor_id = pdev->subsystem_vendor;
865 hw->subsystem_id = pdev->subsystem_device;
866 hw->revision_id = pdev->revision;
868 pci_read_config_word(pdev, PCI_COMMAND, &hw->pci_cmd_word);
870 hw->max_frame_size = adapter->netdev->mtu +
871 ENET_HEADER_SIZE + ETHERNET_FCS_SIZE;
872 hw->min_frame_size = MINIMUM_ETHERNET_FRAME_SIZE;
874 /* identify the MAC */
875 if (e1000_set_mac_type(hw)) {
876 e_err(probe, "Unknown MAC Type\n");
880 switch (hw->mac_type) {
885 case e1000_82541_rev_2:
886 case e1000_82547_rev_2:
887 hw->phy_init_script = 1;
891 e1000_set_media_type(hw);
892 e1000_get_bus_info(hw);
894 hw->wait_autoneg_complete = false;
895 hw->tbi_compatibility_en = true;
896 hw->adaptive_ifs = true;
900 if (hw->media_type == e1000_media_type_copper) {
901 hw->mdix = AUTO_ALL_MODES;
902 hw->disable_polarity_correction = false;
903 hw->master_slave = E1000_MASTER_SLAVE;
910 * e1000_probe - Device Initialization Routine
911 * @pdev: PCI device information struct
912 * @ent: entry in e1000_pci_tbl
914 * Returns 0 on success, negative on failure
916 * e1000_probe initializes an adapter identified by a pci_dev structure.
917 * The OS initialization, configuring of the adapter private structure,
918 * and a hardware reset occur.
920 static int e1000_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
922 struct net_device *netdev;
923 struct e1000_adapter *adapter = NULL;
926 static int cards_found;
927 static int global_quad_port_a; /* global ksp3 port a indication */
928 int i, err, pci_using_dac;
931 u16 eeprom_apme_mask = E1000_EEPROM_APME;
932 int bars, need_ioport;
933 bool disable_dev = false;
935 /* do not allocate ioport bars when not needed */
936 need_ioport = e1000_is_need_ioport(pdev);
938 bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
939 err = pci_enable_device(pdev);
941 bars = pci_select_bars(pdev, IORESOURCE_MEM);
942 err = pci_enable_device_mem(pdev);
947 err = pci_request_selected_regions(pdev, bars, e1000_driver_name);
951 pci_set_master(pdev);
952 err = pci_save_state(pdev);
954 goto err_alloc_etherdev;
957 netdev = alloc_etherdev(sizeof(struct e1000_adapter));
959 goto err_alloc_etherdev;
961 SET_NETDEV_DEV(netdev, &pdev->dev);
963 pci_set_drvdata(pdev, netdev);
964 adapter = netdev_priv(netdev);
965 adapter->netdev = netdev;
966 adapter->pdev = pdev;
967 adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE);
968 adapter->bars = bars;
969 adapter->need_ioport = need_ioport;
975 hw->hw_addr = pci_ioremap_bar(pdev, BAR_0);
979 if (adapter->need_ioport) {
980 for (i = BAR_1; i <= BAR_5; i++) {
981 if (pci_resource_len(pdev, i) == 0)
983 if (pci_resource_flags(pdev, i) & IORESOURCE_IO) {
984 hw->io_base = pci_resource_start(pdev, i);
990 /* make ready for any if (hw->...) below */
991 err = e1000_init_hw_struct(adapter, hw);
995 /* there is a workaround being applied below that limits
996 * 64-bit DMA addresses to 64-bit hardware. There are some
997 * 32-bit adapters that Tx hang when given 64-bit DMA addresses
1000 if ((hw->bus_type == e1000_bus_type_pcix) &&
1001 !dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64))) {
1004 err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
1006 pr_err("No usable DMA config, aborting\n");
1011 netdev->netdev_ops = &e1000_netdev_ops;
1012 e1000_set_ethtool_ops(netdev);
1013 netdev->watchdog_timeo = 5 * HZ;
1014 netif_napi_add(netdev, &adapter->napi, e1000_clean, 64);
1016 strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
1018 adapter->bd_number = cards_found;
1020 /* setup the private structure */
1022 err = e1000_sw_init(adapter);
1027 if (hw->mac_type == e1000_ce4100) {
1028 hw->ce4100_gbe_mdio_base_virt =
1029 ioremap(pci_resource_start(pdev, BAR_1),
1030 pci_resource_len(pdev, BAR_1));
1032 if (!hw->ce4100_gbe_mdio_base_virt)
1033 goto err_mdio_ioremap;
1036 if (hw->mac_type >= e1000_82543) {
1037 netdev->hw_features = NETIF_F_SG |
1039 NETIF_F_HW_VLAN_CTAG_RX;
1040 netdev->features = NETIF_F_HW_VLAN_CTAG_TX |
1041 NETIF_F_HW_VLAN_CTAG_FILTER;
1044 if ((hw->mac_type >= e1000_82544) &&
1045 (hw->mac_type != e1000_82547))
1046 netdev->hw_features |= NETIF_F_TSO;
1048 netdev->priv_flags |= IFF_SUPP_NOFCS;
1050 netdev->features |= netdev->hw_features;
1051 netdev->hw_features |= (NETIF_F_RXCSUM |
1055 if (pci_using_dac) {
1056 netdev->features |= NETIF_F_HIGHDMA;
1057 netdev->vlan_features |= NETIF_F_HIGHDMA;
1060 netdev->vlan_features |= (NETIF_F_TSO |
1064 /* Do not set IFF_UNICAST_FLT for VMWare's 82545EM */
1065 if (hw->device_id != E1000_DEV_ID_82545EM_COPPER ||
1066 hw->subsystem_vendor_id != PCI_VENDOR_ID_VMWARE)
1067 netdev->priv_flags |= IFF_UNICAST_FLT;
1069 /* MTU range: 46 - 16110 */
1070 netdev->min_mtu = ETH_ZLEN - ETH_HLEN;
1071 netdev->max_mtu = MAX_JUMBO_FRAME_SIZE - (ETH_HLEN + ETH_FCS_LEN);
1073 adapter->en_mng_pt = e1000_enable_mng_pass_thru(hw);
1075 /* initialize eeprom parameters */
1076 if (e1000_init_eeprom_params(hw)) {
1077 e_err(probe, "EEPROM initialization failed\n");
1081 /* before reading the EEPROM, reset the controller to
1082 * put the device in a known good starting state
1087 /* make sure the EEPROM is good */
1088 if (e1000_validate_eeprom_checksum(hw) < 0) {
1089 e_err(probe, "The EEPROM Checksum Is Not Valid\n");
1090 e1000_dump_eeprom(adapter);
1091 /* set MAC address to all zeroes to invalidate and temporary
1092 * disable this device for the user. This blocks regular
1093 * traffic while still permitting ethtool ioctls from reaching
1094 * the hardware as well as allowing the user to run the
1095 * interface after manually setting a hw addr using
1098 memset(hw->mac_addr, 0, netdev->addr_len);
1100 /* copy the MAC address out of the EEPROM */
1101 if (e1000_read_mac_addr(hw))
1102 e_err(probe, "EEPROM Read Error\n");
1104 /* don't block initialization here due to bad MAC address */
1105 memcpy(netdev->dev_addr, hw->mac_addr, netdev->addr_len);
1107 if (!is_valid_ether_addr(netdev->dev_addr))
1108 e_err(probe, "Invalid MAC Address\n");
1111 INIT_DELAYED_WORK(&adapter->watchdog_task, e1000_watchdog);
1112 INIT_DELAYED_WORK(&adapter->fifo_stall_task,
1113 e1000_82547_tx_fifo_stall_task);
1114 INIT_DELAYED_WORK(&adapter->phy_info_task, e1000_update_phy_info_task);
1115 INIT_WORK(&adapter->reset_task, e1000_reset_task);
1117 e1000_check_options(adapter);
1119 /* Initial Wake on LAN setting
1120 * If APM wake is enabled in the EEPROM,
1121 * enable the ACPI Magic Packet filter
1124 switch (hw->mac_type) {
1125 case e1000_82542_rev2_0:
1126 case e1000_82542_rev2_1:
1130 e1000_read_eeprom(hw,
1131 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
1132 eeprom_apme_mask = E1000_EEPROM_82544_APM;
1135 case e1000_82546_rev_3:
1136 if (er32(STATUS) & E1000_STATUS_FUNC_1) {
1137 e1000_read_eeprom(hw,
1138 EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
1143 e1000_read_eeprom(hw,
1144 EEPROM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
1147 if (eeprom_data & eeprom_apme_mask)
1148 adapter->eeprom_wol |= E1000_WUFC_MAG;
1150 /* now that we have the eeprom settings, apply the special cases
1151 * where the eeprom may be wrong or the board simply won't support
1152 * wake on lan on a particular port
1154 switch (pdev->device) {
1155 case E1000_DEV_ID_82546GB_PCIE:
1156 adapter->eeprom_wol = 0;
1158 case E1000_DEV_ID_82546EB_FIBER:
1159 case E1000_DEV_ID_82546GB_FIBER:
1160 /* Wake events only supported on port A for dual fiber
1161 * regardless of eeprom setting
1163 if (er32(STATUS) & E1000_STATUS_FUNC_1)
1164 adapter->eeprom_wol = 0;
1166 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
1167 /* if quad port adapter, disable WoL on all but port A */
1168 if (global_quad_port_a != 0)
1169 adapter->eeprom_wol = 0;
1171 adapter->quad_port_a = true;
1172 /* Reset for multiple quad port adapters */
1173 if (++global_quad_port_a == 4)
1174 global_quad_port_a = 0;
1178 /* initialize the wol settings based on the eeprom settings */
1179 adapter->wol = adapter->eeprom_wol;
1180 device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
1182 /* Auto detect PHY address */
1183 if (hw->mac_type == e1000_ce4100) {
1184 for (i = 0; i < 32; i++) {
1186 e1000_read_phy_reg(hw, PHY_ID2, &tmp);
1188 if (tmp != 0 && tmp != 0xFF)
1196 /* reset the hardware with the new settings */
1197 e1000_reset(adapter);
1199 strcpy(netdev->name, "eth%d");
1200 err = register_netdev(netdev);
1204 e1000_vlan_filter_on_off(adapter, false);
1206 /* print bus type/speed/width info */
1207 e_info(probe, "(PCI%s:%dMHz:%d-bit) %pM\n",
1208 ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : ""),
1209 ((hw->bus_speed == e1000_bus_speed_133) ? 133 :
1210 (hw->bus_speed == e1000_bus_speed_120) ? 120 :
1211 (hw->bus_speed == e1000_bus_speed_100) ? 100 :
1212 (hw->bus_speed == e1000_bus_speed_66) ? 66 : 33),
1213 ((hw->bus_width == e1000_bus_width_64) ? 64 : 32),
1216 /* carrier off reporting is important to ethtool even BEFORE open */
1217 netif_carrier_off(netdev);
1219 e_info(probe, "Intel(R) PRO/1000 Network Connection\n");
1226 e1000_phy_hw_reset(hw);
1228 if (hw->flash_address)
1229 iounmap(hw->flash_address);
1230 kfree(adapter->tx_ring);
1231 kfree(adapter->rx_ring);
1235 iounmap(hw->ce4100_gbe_mdio_base_virt);
1236 iounmap(hw->hw_addr);
1238 disable_dev = !test_and_set_bit(__E1000_DISABLED, &adapter->flags);
1239 free_netdev(netdev);
1241 pci_release_selected_regions(pdev, bars);
1243 if (!adapter || disable_dev)
1244 pci_disable_device(pdev);
1249 * e1000_remove - Device Removal Routine
1250 * @pdev: PCI device information struct
1252 * e1000_remove is called by the PCI subsystem to alert the driver
1253 * that it should release a PCI device. That could be caused by a
1254 * Hot-Plug event, or because the driver is going to be removed from
1257 static void e1000_remove(struct pci_dev *pdev)
1259 struct net_device *netdev = pci_get_drvdata(pdev);
1260 struct e1000_adapter *adapter = netdev_priv(netdev);
1261 struct e1000_hw *hw = &adapter->hw;
1264 e1000_down_and_stop(adapter);
1265 e1000_release_manageability(adapter);
1267 unregister_netdev(netdev);
1269 e1000_phy_hw_reset(hw);
1271 kfree(adapter->tx_ring);
1272 kfree(adapter->rx_ring);
1274 if (hw->mac_type == e1000_ce4100)
1275 iounmap(hw->ce4100_gbe_mdio_base_virt);
1276 iounmap(hw->hw_addr);
1277 if (hw->flash_address)
1278 iounmap(hw->flash_address);
1279 pci_release_selected_regions(pdev, adapter->bars);
1281 disable_dev = !test_and_set_bit(__E1000_DISABLED, &adapter->flags);
1282 free_netdev(netdev);
1285 pci_disable_device(pdev);
1289 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
1290 * @adapter: board private structure to initialize
1292 * e1000_sw_init initializes the Adapter private data structure.
1293 * e1000_init_hw_struct MUST be called before this function
1295 static int e1000_sw_init(struct e1000_adapter *adapter)
1297 adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
1299 adapter->num_tx_queues = 1;
1300 adapter->num_rx_queues = 1;
1302 if (e1000_alloc_queues(adapter)) {
1303 e_err(probe, "Unable to allocate memory for queues\n");
1307 /* Explicitly disable IRQ since the NIC can be in any state. */
1308 e1000_irq_disable(adapter);
1310 spin_lock_init(&adapter->stats_lock);
1312 set_bit(__E1000_DOWN, &adapter->flags);
1318 * e1000_alloc_queues - Allocate memory for all rings
1319 * @adapter: board private structure to initialize
1321 * We allocate one ring per queue at run-time since we don't know the
1322 * number of queues at compile-time.
1324 static int e1000_alloc_queues(struct e1000_adapter *adapter)
1326 adapter->tx_ring = kcalloc(adapter->num_tx_queues,
1327 sizeof(struct e1000_tx_ring), GFP_KERNEL);
1328 if (!adapter->tx_ring)
1331 adapter->rx_ring = kcalloc(adapter->num_rx_queues,
1332 sizeof(struct e1000_rx_ring), GFP_KERNEL);
1333 if (!adapter->rx_ring) {
1334 kfree(adapter->tx_ring);
1338 return E1000_SUCCESS;
1342 * e1000_open - Called when a network interface is made active
1343 * @netdev: network interface device structure
1345 * Returns 0 on success, negative value on failure
1347 * The open entry point is called when a network interface is made
1348 * active by the system (IFF_UP). At this point all resources needed
1349 * for transmit and receive operations are allocated, the interrupt
1350 * handler is registered with the OS, the watchdog task is started,
1351 * and the stack is notified that the interface is ready.
1353 int e1000_open(struct net_device *netdev)
1355 struct e1000_adapter *adapter = netdev_priv(netdev);
1356 struct e1000_hw *hw = &adapter->hw;
1359 /* disallow open during test */
1360 if (test_bit(__E1000_TESTING, &adapter->flags))
1363 netif_carrier_off(netdev);
1365 /* allocate transmit descriptors */
1366 err = e1000_setup_all_tx_resources(adapter);
1370 /* allocate receive descriptors */
1371 err = e1000_setup_all_rx_resources(adapter);
1375 e1000_power_up_phy(adapter);
1377 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
1378 if ((hw->mng_cookie.status &
1379 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) {
1380 e1000_update_mng_vlan(adapter);
1383 /* before we allocate an interrupt, we must be ready to handle it.
1384 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
1385 * as soon as we call pci_request_irq, so we have to setup our
1386 * clean_rx handler before we do so.
1388 e1000_configure(adapter);
1390 err = e1000_request_irq(adapter);
1394 /* From here on the code is the same as e1000_up() */
1395 clear_bit(__E1000_DOWN, &adapter->flags);
1397 napi_enable(&adapter->napi);
1399 e1000_irq_enable(adapter);
1401 netif_start_queue(netdev);
1403 /* fire a link status change interrupt to start the watchdog */
1404 ew32(ICS, E1000_ICS_LSC);
1406 return E1000_SUCCESS;
1409 e1000_power_down_phy(adapter);
1410 e1000_free_all_rx_resources(adapter);
1412 e1000_free_all_tx_resources(adapter);
1414 e1000_reset(adapter);
1420 * e1000_close - Disables a network interface
1421 * @netdev: network interface device structure
1423 * Returns 0, this is not allowed to fail
1425 * The close entry point is called when an interface is de-activated
1426 * by the OS. The hardware is still under the drivers control, but
1427 * needs to be disabled. A global MAC reset is issued to stop the
1428 * hardware, and all transmit and receive resources are freed.
1430 int e1000_close(struct net_device *netdev)
1432 struct e1000_adapter *adapter = netdev_priv(netdev);
1433 struct e1000_hw *hw = &adapter->hw;
1434 int count = E1000_CHECK_RESET_COUNT;
1436 while (test_bit(__E1000_RESETTING, &adapter->flags) && count--)
1437 usleep_range(10000, 20000);
1439 WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
1440 e1000_down(adapter);
1441 e1000_power_down_phy(adapter);
1442 e1000_free_irq(adapter);
1444 e1000_free_all_tx_resources(adapter);
1445 e1000_free_all_rx_resources(adapter);
1447 /* kill manageability vlan ID if supported, but not if a vlan with
1448 * the same ID is registered on the host OS (let 8021q kill it)
1450 if ((hw->mng_cookie.status &
1451 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
1452 !test_bit(adapter->mng_vlan_id, adapter->active_vlans)) {
1453 e1000_vlan_rx_kill_vid(netdev, htons(ETH_P_8021Q),
1454 adapter->mng_vlan_id);
1461 * e1000_check_64k_bound - check that memory doesn't cross 64kB boundary
1462 * @adapter: address of board private structure
1463 * @start: address of beginning of memory
1464 * @len: length of memory
1466 static bool e1000_check_64k_bound(struct e1000_adapter *adapter, void *start,
1469 struct e1000_hw *hw = &adapter->hw;
1470 unsigned long begin = (unsigned long)start;
1471 unsigned long end = begin + len;
1473 /* First rev 82545 and 82546 need to not allow any memory
1474 * write location to cross 64k boundary due to errata 23
1476 if (hw->mac_type == e1000_82545 ||
1477 hw->mac_type == e1000_ce4100 ||
1478 hw->mac_type == e1000_82546) {
1479 return ((begin ^ (end - 1)) >> 16) != 0 ? false : true;
1486 * e1000_setup_tx_resources - allocate Tx resources (Descriptors)
1487 * @adapter: board private structure
1488 * @txdr: tx descriptor ring (for a specific queue) to setup
1490 * Return 0 on success, negative on failure
1492 static int e1000_setup_tx_resources(struct e1000_adapter *adapter,
1493 struct e1000_tx_ring *txdr)
1495 struct pci_dev *pdev = adapter->pdev;
1498 size = sizeof(struct e1000_tx_buffer) * txdr->count;
1499 txdr->buffer_info = vzalloc(size);
1500 if (!txdr->buffer_info)
1503 /* round up to nearest 4K */
1505 txdr->size = txdr->count * sizeof(struct e1000_tx_desc);
1506 txdr->size = ALIGN(txdr->size, 4096);
1508 txdr->desc = dma_alloc_coherent(&pdev->dev, txdr->size, &txdr->dma,
1512 vfree(txdr->buffer_info);
1516 /* Fix for errata 23, can't cross 64kB boundary */
1517 if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
1518 void *olddesc = txdr->desc;
1519 dma_addr_t olddma = txdr->dma;
1520 e_err(tx_err, "txdr align check failed: %u bytes at %p\n",
1521 txdr->size, txdr->desc);
1522 /* Try again, without freeing the previous */
1523 txdr->desc = dma_alloc_coherent(&pdev->dev, txdr->size,
1524 &txdr->dma, GFP_KERNEL);
1525 /* Failed allocation, critical failure */
1527 dma_free_coherent(&pdev->dev, txdr->size, olddesc,
1529 goto setup_tx_desc_die;
1532 if (!e1000_check_64k_bound(adapter, txdr->desc, txdr->size)) {
1534 dma_free_coherent(&pdev->dev, txdr->size, txdr->desc,
1536 dma_free_coherent(&pdev->dev, txdr->size, olddesc,
1538 e_err(probe, "Unable to allocate aligned memory "
1539 "for the transmit descriptor ring\n");
1540 vfree(txdr->buffer_info);
1543 /* Free old allocation, new allocation was successful */
1544 dma_free_coherent(&pdev->dev, txdr->size, olddesc,
1548 memset(txdr->desc, 0, txdr->size);
1550 txdr->next_to_use = 0;
1551 txdr->next_to_clean = 0;
1557 * e1000_setup_all_tx_resources - wrapper to allocate Tx resources
1558 * (Descriptors) for all queues
1559 * @adapter: board private structure
1561 * Return 0 on success, negative on failure
1563 int e1000_setup_all_tx_resources(struct e1000_adapter *adapter)
1567 for (i = 0; i < adapter->num_tx_queues; i++) {
1568 err = e1000_setup_tx_resources(adapter, &adapter->tx_ring[i]);
1570 e_err(probe, "Allocation for Tx Queue %u failed\n", i);
1571 for (i-- ; i >= 0; i--)
1572 e1000_free_tx_resources(adapter,
1573 &adapter->tx_ring[i]);
1582 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
1583 * @adapter: board private structure
1585 * Configure the Tx unit of the MAC after a reset.
1587 static void e1000_configure_tx(struct e1000_adapter *adapter)
1590 struct e1000_hw *hw = &adapter->hw;
1591 u32 tdlen, tctl, tipg;
1594 /* Setup the HW Tx Head and Tail descriptor pointers */
1596 switch (adapter->num_tx_queues) {
1599 tdba = adapter->tx_ring[0].dma;
1600 tdlen = adapter->tx_ring[0].count *
1601 sizeof(struct e1000_tx_desc);
1603 ew32(TDBAH, (tdba >> 32));
1604 ew32(TDBAL, (tdba & 0x00000000ffffffffULL));
1607 adapter->tx_ring[0].tdh = ((hw->mac_type >= e1000_82543) ?
1608 E1000_TDH : E1000_82542_TDH);
1609 adapter->tx_ring[0].tdt = ((hw->mac_type >= e1000_82543) ?
1610 E1000_TDT : E1000_82542_TDT);
1614 /* Set the default values for the Tx Inter Packet Gap timer */
1615 if ((hw->media_type == e1000_media_type_fiber ||
1616 hw->media_type == e1000_media_type_internal_serdes))
1617 tipg = DEFAULT_82543_TIPG_IPGT_FIBER;
1619 tipg = DEFAULT_82543_TIPG_IPGT_COPPER;
1621 switch (hw->mac_type) {
1622 case e1000_82542_rev2_0:
1623 case e1000_82542_rev2_1:
1624 tipg = DEFAULT_82542_TIPG_IPGT;
1625 ipgr1 = DEFAULT_82542_TIPG_IPGR1;
1626 ipgr2 = DEFAULT_82542_TIPG_IPGR2;
1629 ipgr1 = DEFAULT_82543_TIPG_IPGR1;
1630 ipgr2 = DEFAULT_82543_TIPG_IPGR2;
1633 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
1634 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
1637 /* Set the Tx Interrupt Delay register */
1639 ew32(TIDV, adapter->tx_int_delay);
1640 if (hw->mac_type >= e1000_82540)
1641 ew32(TADV, adapter->tx_abs_int_delay);
1643 /* Program the Transmit Control Register */
1646 tctl &= ~E1000_TCTL_CT;
1647 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
1648 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
1650 e1000_config_collision_dist(hw);
1652 /* Setup Transmit Descriptor Settings for eop descriptor */
1653 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
1655 /* only set IDE if we are delaying interrupts using the timers */
1656 if (adapter->tx_int_delay)
1657 adapter->txd_cmd |= E1000_TXD_CMD_IDE;
1659 if (hw->mac_type < e1000_82543)
1660 adapter->txd_cmd |= E1000_TXD_CMD_RPS;
1662 adapter->txd_cmd |= E1000_TXD_CMD_RS;
1664 /* Cache if we're 82544 running in PCI-X because we'll
1665 * need this to apply a workaround later in the send path.
1667 if (hw->mac_type == e1000_82544 &&
1668 hw->bus_type == e1000_bus_type_pcix)
1669 adapter->pcix_82544 = true;
1676 * e1000_setup_rx_resources - allocate Rx resources (Descriptors)
1677 * @adapter: board private structure
1678 * @rxdr: rx descriptor ring (for a specific queue) to setup
1680 * Returns 0 on success, negative on failure
1682 static int e1000_setup_rx_resources(struct e1000_adapter *adapter,
1683 struct e1000_rx_ring *rxdr)
1685 struct pci_dev *pdev = adapter->pdev;
1688 size = sizeof(struct e1000_rx_buffer) * rxdr->count;
1689 rxdr->buffer_info = vzalloc(size);
1690 if (!rxdr->buffer_info)
1693 desc_len = sizeof(struct e1000_rx_desc);
1695 /* Round up to nearest 4K */
1697 rxdr->size = rxdr->count * desc_len;
1698 rxdr->size = ALIGN(rxdr->size, 4096);
1700 rxdr->desc = dma_alloc_coherent(&pdev->dev, rxdr->size, &rxdr->dma,
1704 vfree(rxdr->buffer_info);
1708 /* Fix for errata 23, can't cross 64kB boundary */
1709 if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
1710 void *olddesc = rxdr->desc;
1711 dma_addr_t olddma = rxdr->dma;
1712 e_err(rx_err, "rxdr align check failed: %u bytes at %p\n",
1713 rxdr->size, rxdr->desc);
1714 /* Try again, without freeing the previous */
1715 rxdr->desc = dma_alloc_coherent(&pdev->dev, rxdr->size,
1716 &rxdr->dma, GFP_KERNEL);
1717 /* Failed allocation, critical failure */
1719 dma_free_coherent(&pdev->dev, rxdr->size, olddesc,
1721 goto setup_rx_desc_die;
1724 if (!e1000_check_64k_bound(adapter, rxdr->desc, rxdr->size)) {
1726 dma_free_coherent(&pdev->dev, rxdr->size, rxdr->desc,
1728 dma_free_coherent(&pdev->dev, rxdr->size, olddesc,
1730 e_err(probe, "Unable to allocate aligned memory for "
1731 "the Rx descriptor ring\n");
1732 goto setup_rx_desc_die;
1734 /* Free old allocation, new allocation was successful */
1735 dma_free_coherent(&pdev->dev, rxdr->size, olddesc,
1739 memset(rxdr->desc, 0, rxdr->size);
1741 rxdr->next_to_clean = 0;
1742 rxdr->next_to_use = 0;
1743 rxdr->rx_skb_top = NULL;
1749 * e1000_setup_all_rx_resources - wrapper to allocate Rx resources
1750 * (Descriptors) for all queues
1751 * @adapter: board private structure
1753 * Return 0 on success, negative on failure
1755 int e1000_setup_all_rx_resources(struct e1000_adapter *adapter)
1759 for (i = 0; i < adapter->num_rx_queues; i++) {
1760 err = e1000_setup_rx_resources(adapter, &adapter->rx_ring[i]);
1762 e_err(probe, "Allocation for Rx Queue %u failed\n", i);
1763 for (i-- ; i >= 0; i--)
1764 e1000_free_rx_resources(adapter,
1765 &adapter->rx_ring[i]);
1774 * e1000_setup_rctl - configure the receive control registers
1775 * @adapter: Board private structure
1777 static void e1000_setup_rctl(struct e1000_adapter *adapter)
1779 struct e1000_hw *hw = &adapter->hw;
1784 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
1786 rctl |= E1000_RCTL_BAM | E1000_RCTL_LBM_NO |
1787 E1000_RCTL_RDMTS_HALF |
1788 (hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
1790 if (hw->tbi_compatibility_on == 1)
1791 rctl |= E1000_RCTL_SBP;
1793 rctl &= ~E1000_RCTL_SBP;
1795 if (adapter->netdev->mtu <= ETH_DATA_LEN)
1796 rctl &= ~E1000_RCTL_LPE;
1798 rctl |= E1000_RCTL_LPE;
1800 /* Setup buffer sizes */
1801 rctl &= ~E1000_RCTL_SZ_4096;
1802 rctl |= E1000_RCTL_BSEX;
1803 switch (adapter->rx_buffer_len) {
1804 case E1000_RXBUFFER_2048:
1806 rctl |= E1000_RCTL_SZ_2048;
1807 rctl &= ~E1000_RCTL_BSEX;
1809 case E1000_RXBUFFER_4096:
1810 rctl |= E1000_RCTL_SZ_4096;
1812 case E1000_RXBUFFER_8192:
1813 rctl |= E1000_RCTL_SZ_8192;
1815 case E1000_RXBUFFER_16384:
1816 rctl |= E1000_RCTL_SZ_16384;
1820 /* This is useful for sniffing bad packets. */
1821 if (adapter->netdev->features & NETIF_F_RXALL) {
1822 /* UPE and MPE will be handled by normal PROMISC logic
1823 * in e1000e_set_rx_mode
1825 rctl |= (E1000_RCTL_SBP | /* Receive bad packets */
1826 E1000_RCTL_BAM | /* RX All Bcast Pkts */
1827 E1000_RCTL_PMCF); /* RX All MAC Ctrl Pkts */
1829 rctl &= ~(E1000_RCTL_VFE | /* Disable VLAN filter */
1830 E1000_RCTL_DPF | /* Allow filtered pause */
1831 E1000_RCTL_CFIEN); /* Dis VLAN CFIEN Filter */
1832 /* Do not mess with E1000_CTRL_VME, it affects transmit as well,
1833 * and that breaks VLANs.
1841 * e1000_configure_rx - Configure 8254x Receive Unit after Reset
1842 * @adapter: board private structure
1844 * Configure the Rx unit of the MAC after a reset.
1846 static void e1000_configure_rx(struct e1000_adapter *adapter)
1849 struct e1000_hw *hw = &adapter->hw;
1850 u32 rdlen, rctl, rxcsum;
1852 if (adapter->netdev->mtu > ETH_DATA_LEN) {
1853 rdlen = adapter->rx_ring[0].count *
1854 sizeof(struct e1000_rx_desc);
1855 adapter->clean_rx = e1000_clean_jumbo_rx_irq;
1856 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
1858 rdlen = adapter->rx_ring[0].count *
1859 sizeof(struct e1000_rx_desc);
1860 adapter->clean_rx = e1000_clean_rx_irq;
1861 adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
1864 /* disable receives while setting up the descriptors */
1866 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1868 /* set the Receive Delay Timer Register */
1869 ew32(RDTR, adapter->rx_int_delay);
1871 if (hw->mac_type >= e1000_82540) {
1872 ew32(RADV, adapter->rx_abs_int_delay);
1873 if (adapter->itr_setting != 0)
1874 ew32(ITR, 1000000000 / (adapter->itr * 256));
1877 /* Setup the HW Rx Head and Tail Descriptor Pointers and
1878 * the Base and Length of the Rx Descriptor Ring
1880 switch (adapter->num_rx_queues) {
1883 rdba = adapter->rx_ring[0].dma;
1885 ew32(RDBAH, (rdba >> 32));
1886 ew32(RDBAL, (rdba & 0x00000000ffffffffULL));
1889 adapter->rx_ring[0].rdh = ((hw->mac_type >= e1000_82543) ?
1890 E1000_RDH : E1000_82542_RDH);
1891 adapter->rx_ring[0].rdt = ((hw->mac_type >= e1000_82543) ?
1892 E1000_RDT : E1000_82542_RDT);
1896 /* Enable 82543 Receive Checksum Offload for TCP and UDP */
1897 if (hw->mac_type >= e1000_82543) {
1898 rxcsum = er32(RXCSUM);
1899 if (adapter->rx_csum)
1900 rxcsum |= E1000_RXCSUM_TUOFL;
1902 /* don't need to clear IPPCSE as it defaults to 0 */
1903 rxcsum &= ~E1000_RXCSUM_TUOFL;
1904 ew32(RXCSUM, rxcsum);
1907 /* Enable Receives */
1908 ew32(RCTL, rctl | E1000_RCTL_EN);
1912 * e1000_free_tx_resources - Free Tx Resources per Queue
1913 * @adapter: board private structure
1914 * @tx_ring: Tx descriptor ring for a specific queue
1916 * Free all transmit software resources
1918 static void e1000_free_tx_resources(struct e1000_adapter *adapter,
1919 struct e1000_tx_ring *tx_ring)
1921 struct pci_dev *pdev = adapter->pdev;
1923 e1000_clean_tx_ring(adapter, tx_ring);
1925 vfree(tx_ring->buffer_info);
1926 tx_ring->buffer_info = NULL;
1928 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
1931 tx_ring->desc = NULL;
1935 * e1000_free_all_tx_resources - Free Tx Resources for All Queues
1936 * @adapter: board private structure
1938 * Free all transmit software resources
1940 void e1000_free_all_tx_resources(struct e1000_adapter *adapter)
1944 for (i = 0; i < adapter->num_tx_queues; i++)
1945 e1000_free_tx_resources(adapter, &adapter->tx_ring[i]);
1949 e1000_unmap_and_free_tx_resource(struct e1000_adapter *adapter,
1950 struct e1000_tx_buffer *buffer_info)
1952 if (buffer_info->dma) {
1953 if (buffer_info->mapped_as_page)
1954 dma_unmap_page(&adapter->pdev->dev, buffer_info->dma,
1955 buffer_info->length, DMA_TO_DEVICE);
1957 dma_unmap_single(&adapter->pdev->dev, buffer_info->dma,
1958 buffer_info->length,
1960 buffer_info->dma = 0;
1962 if (buffer_info->skb) {
1963 dev_kfree_skb_any(buffer_info->skb);
1964 buffer_info->skb = NULL;
1966 buffer_info->time_stamp = 0;
1967 /* buffer_info must be completely set up in the transmit path */
1971 * e1000_clean_tx_ring - Free Tx Buffers
1972 * @adapter: board private structure
1973 * @tx_ring: ring to be cleaned
1975 static void e1000_clean_tx_ring(struct e1000_adapter *adapter,
1976 struct e1000_tx_ring *tx_ring)
1978 struct e1000_hw *hw = &adapter->hw;
1979 struct e1000_tx_buffer *buffer_info;
1983 /* Free all the Tx ring sk_buffs */
1985 for (i = 0; i < tx_ring->count; i++) {
1986 buffer_info = &tx_ring->buffer_info[i];
1987 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
1990 netdev_reset_queue(adapter->netdev);
1991 size = sizeof(struct e1000_tx_buffer) * tx_ring->count;
1992 memset(tx_ring->buffer_info, 0, size);
1994 /* Zero out the descriptor ring */
1996 memset(tx_ring->desc, 0, tx_ring->size);
1998 tx_ring->next_to_use = 0;
1999 tx_ring->next_to_clean = 0;
2000 tx_ring->last_tx_tso = false;
2002 writel(0, hw->hw_addr + tx_ring->tdh);
2003 writel(0, hw->hw_addr + tx_ring->tdt);
2007 * e1000_clean_all_tx_rings - Free Tx Buffers for all queues
2008 * @adapter: board private structure
2010 static void e1000_clean_all_tx_rings(struct e1000_adapter *adapter)
2014 for (i = 0; i < adapter->num_tx_queues; i++)
2015 e1000_clean_tx_ring(adapter, &adapter->tx_ring[i]);
2019 * e1000_free_rx_resources - Free Rx Resources
2020 * @adapter: board private structure
2021 * @rx_ring: ring to clean the resources from
2023 * Free all receive software resources
2025 static void e1000_free_rx_resources(struct e1000_adapter *adapter,
2026 struct e1000_rx_ring *rx_ring)
2028 struct pci_dev *pdev = adapter->pdev;
2030 e1000_clean_rx_ring(adapter, rx_ring);
2032 vfree(rx_ring->buffer_info);
2033 rx_ring->buffer_info = NULL;
2035 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
2038 rx_ring->desc = NULL;
2042 * e1000_free_all_rx_resources - Free Rx Resources for All Queues
2043 * @adapter: board private structure
2045 * Free all receive software resources
2047 void e1000_free_all_rx_resources(struct e1000_adapter *adapter)
2051 for (i = 0; i < adapter->num_rx_queues; i++)
2052 e1000_free_rx_resources(adapter, &adapter->rx_ring[i]);
2055 #define E1000_HEADROOM (NET_SKB_PAD + NET_IP_ALIGN)
2056 static unsigned int e1000_frag_len(const struct e1000_adapter *a)
2058 return SKB_DATA_ALIGN(a->rx_buffer_len + E1000_HEADROOM) +
2059 SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
2062 static void *e1000_alloc_frag(const struct e1000_adapter *a)
2064 unsigned int len = e1000_frag_len(a);
2065 u8 *data = netdev_alloc_frag(len);
2068 data += E1000_HEADROOM;
2073 * e1000_clean_rx_ring - Free Rx Buffers per Queue
2074 * @adapter: board private structure
2075 * @rx_ring: ring to free buffers from
2077 static void e1000_clean_rx_ring(struct e1000_adapter *adapter,
2078 struct e1000_rx_ring *rx_ring)
2080 struct e1000_hw *hw = &adapter->hw;
2081 struct e1000_rx_buffer *buffer_info;
2082 struct pci_dev *pdev = adapter->pdev;
2086 /* Free all the Rx netfrags */
2087 for (i = 0; i < rx_ring->count; i++) {
2088 buffer_info = &rx_ring->buffer_info[i];
2089 if (adapter->clean_rx == e1000_clean_rx_irq) {
2090 if (buffer_info->dma)
2091 dma_unmap_single(&pdev->dev, buffer_info->dma,
2092 adapter->rx_buffer_len,
2094 if (buffer_info->rxbuf.data) {
2095 skb_free_frag(buffer_info->rxbuf.data);
2096 buffer_info->rxbuf.data = NULL;
2098 } else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq) {
2099 if (buffer_info->dma)
2100 dma_unmap_page(&pdev->dev, buffer_info->dma,
2101 adapter->rx_buffer_len,
2103 if (buffer_info->rxbuf.page) {
2104 put_page(buffer_info->rxbuf.page);
2105 buffer_info->rxbuf.page = NULL;
2109 buffer_info->dma = 0;
2112 /* there also may be some cached data from a chained receive */
2113 napi_free_frags(&adapter->napi);
2114 rx_ring->rx_skb_top = NULL;
2116 size = sizeof(struct e1000_rx_buffer) * rx_ring->count;
2117 memset(rx_ring->buffer_info, 0, size);
2119 /* Zero out the descriptor ring */
2120 memset(rx_ring->desc, 0, rx_ring->size);
2122 rx_ring->next_to_clean = 0;
2123 rx_ring->next_to_use = 0;
2125 writel(0, hw->hw_addr + rx_ring->rdh);
2126 writel(0, hw->hw_addr + rx_ring->rdt);
2130 * e1000_clean_all_rx_rings - Free Rx Buffers for all queues
2131 * @adapter: board private structure
2133 static void e1000_clean_all_rx_rings(struct e1000_adapter *adapter)
2137 for (i = 0; i < adapter->num_rx_queues; i++)
2138 e1000_clean_rx_ring(adapter, &adapter->rx_ring[i]);
2141 /* The 82542 2.0 (revision 2) needs to have the receive unit in reset
2142 * and memory write and invalidate disabled for certain operations
2144 static void e1000_enter_82542_rst(struct e1000_adapter *adapter)
2146 struct e1000_hw *hw = &adapter->hw;
2147 struct net_device *netdev = adapter->netdev;
2150 e1000_pci_clear_mwi(hw);
2153 rctl |= E1000_RCTL_RST;
2155 E1000_WRITE_FLUSH();
2158 if (netif_running(netdev))
2159 e1000_clean_all_rx_rings(adapter);
2162 static void e1000_leave_82542_rst(struct e1000_adapter *adapter)
2164 struct e1000_hw *hw = &adapter->hw;
2165 struct net_device *netdev = adapter->netdev;
2169 rctl &= ~E1000_RCTL_RST;
2171 E1000_WRITE_FLUSH();
2174 if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE)
2175 e1000_pci_set_mwi(hw);
2177 if (netif_running(netdev)) {
2178 /* No need to loop, because 82542 supports only 1 queue */
2179 struct e1000_rx_ring *ring = &adapter->rx_ring[0];
2180 e1000_configure_rx(adapter);
2181 adapter->alloc_rx_buf(adapter, ring, E1000_DESC_UNUSED(ring));
2186 * e1000_set_mac - Change the Ethernet Address of the NIC
2187 * @netdev: network interface device structure
2188 * @p: pointer to an address structure
2190 * Returns 0 on success, negative on failure
2192 static int e1000_set_mac(struct net_device *netdev, void *p)
2194 struct e1000_adapter *adapter = netdev_priv(netdev);
2195 struct e1000_hw *hw = &adapter->hw;
2196 struct sockaddr *addr = p;
2198 if (!is_valid_ether_addr(addr->sa_data))
2199 return -EADDRNOTAVAIL;
2201 /* 82542 2.0 needs to be in reset to write receive address registers */
2203 if (hw->mac_type == e1000_82542_rev2_0)
2204 e1000_enter_82542_rst(adapter);
2206 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
2207 memcpy(hw->mac_addr, addr->sa_data, netdev->addr_len);
2209 e1000_rar_set(hw, hw->mac_addr, 0);
2211 if (hw->mac_type == e1000_82542_rev2_0)
2212 e1000_leave_82542_rst(adapter);
2218 * e1000_set_rx_mode - Secondary Unicast, Multicast and Promiscuous mode set
2219 * @netdev: network interface device structure
2221 * The set_rx_mode entry point is called whenever the unicast or multicast
2222 * address lists or the network interface flags are updated. This routine is
2223 * responsible for configuring the hardware for proper unicast, multicast,
2224 * promiscuous mode, and all-multi behavior.
2226 static void e1000_set_rx_mode(struct net_device *netdev)
2228 struct e1000_adapter *adapter = netdev_priv(netdev);
2229 struct e1000_hw *hw = &adapter->hw;
2230 struct netdev_hw_addr *ha;
2231 bool use_uc = false;
2234 int i, rar_entries = E1000_RAR_ENTRIES;
2235 int mta_reg_count = E1000_NUM_MTA_REGISTERS;
2236 u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC);
2241 /* Check for Promiscuous and All Multicast modes */
2245 if (netdev->flags & IFF_PROMISC) {
2246 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
2247 rctl &= ~E1000_RCTL_VFE;
2249 if (netdev->flags & IFF_ALLMULTI)
2250 rctl |= E1000_RCTL_MPE;
2252 rctl &= ~E1000_RCTL_MPE;
2253 /* Enable VLAN filter if there is a VLAN */
2254 if (e1000_vlan_used(adapter))
2255 rctl |= E1000_RCTL_VFE;
2258 if (netdev_uc_count(netdev) > rar_entries - 1) {
2259 rctl |= E1000_RCTL_UPE;
2260 } else if (!(netdev->flags & IFF_PROMISC)) {
2261 rctl &= ~E1000_RCTL_UPE;
2267 /* 82542 2.0 needs to be in reset to write receive address registers */
2269 if (hw->mac_type == e1000_82542_rev2_0)
2270 e1000_enter_82542_rst(adapter);
2272 /* load the first 14 addresses into the exact filters 1-14. Unicast
2273 * addresses take precedence to avoid disabling unicast filtering
2276 * RAR 0 is used for the station MAC address
2277 * if there are not 14 addresses, go ahead and clear the filters
2281 netdev_for_each_uc_addr(ha, netdev) {
2282 if (i == rar_entries)
2284 e1000_rar_set(hw, ha->addr, i++);
2287 netdev_for_each_mc_addr(ha, netdev) {
2288 if (i == rar_entries) {
2289 /* load any remaining addresses into the hash table */
2290 u32 hash_reg, hash_bit, mta;
2291 hash_value = e1000_hash_mc_addr(hw, ha->addr);
2292 hash_reg = (hash_value >> 5) & 0x7F;
2293 hash_bit = hash_value & 0x1F;
2294 mta = (1 << hash_bit);
2295 mcarray[hash_reg] |= mta;
2297 e1000_rar_set(hw, ha->addr, i++);
2301 for (; i < rar_entries; i++) {
2302 E1000_WRITE_REG_ARRAY(hw, RA, i << 1, 0);
2303 E1000_WRITE_FLUSH();
2304 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1) + 1, 0);
2305 E1000_WRITE_FLUSH();
2308 /* write the hash table completely, write from bottom to avoid
2309 * both stupid write combining chipsets, and flushing each write
2311 for (i = mta_reg_count - 1; i >= 0 ; i--) {
2312 /* If we are on an 82544 has an errata where writing odd
2313 * offsets overwrites the previous even offset, but writing
2314 * backwards over the range solves the issue by always
2315 * writing the odd offset first
2317 E1000_WRITE_REG_ARRAY(hw, MTA, i, mcarray[i]);
2319 E1000_WRITE_FLUSH();
2321 if (hw->mac_type == e1000_82542_rev2_0)
2322 e1000_leave_82542_rst(adapter);
2328 * e1000_update_phy_info_task - get phy info
2329 * @work: work struct contained inside adapter struct
2331 * Need to wait a few seconds after link up to get diagnostic information from
2334 static void e1000_update_phy_info_task(struct work_struct *work)
2336 struct e1000_adapter *adapter = container_of(work,
2337 struct e1000_adapter,
2338 phy_info_task.work);
2340 e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
2344 * e1000_82547_tx_fifo_stall_task - task to complete work
2345 * @work: work struct contained inside adapter struct
2347 static void e1000_82547_tx_fifo_stall_task(struct work_struct *work)
2349 struct e1000_adapter *adapter = container_of(work,
2350 struct e1000_adapter,
2351 fifo_stall_task.work);
2352 struct e1000_hw *hw = &adapter->hw;
2353 struct net_device *netdev = adapter->netdev;
2356 if (atomic_read(&adapter->tx_fifo_stall)) {
2357 if ((er32(TDT) == er32(TDH)) &&
2358 (er32(TDFT) == er32(TDFH)) &&
2359 (er32(TDFTS) == er32(TDFHS))) {
2361 ew32(TCTL, tctl & ~E1000_TCTL_EN);
2362 ew32(TDFT, adapter->tx_head_addr);
2363 ew32(TDFH, adapter->tx_head_addr);
2364 ew32(TDFTS, adapter->tx_head_addr);
2365 ew32(TDFHS, adapter->tx_head_addr);
2367 E1000_WRITE_FLUSH();
2369 adapter->tx_fifo_head = 0;
2370 atomic_set(&adapter->tx_fifo_stall, 0);
2371 netif_wake_queue(netdev);
2372 } else if (!test_bit(__E1000_DOWN, &adapter->flags)) {
2373 schedule_delayed_work(&adapter->fifo_stall_task, 1);
2378 bool e1000_has_link(struct e1000_adapter *adapter)
2380 struct e1000_hw *hw = &adapter->hw;
2381 bool link_active = false;
2383 /* get_link_status is set on LSC (link status) interrupt or rx
2384 * sequence error interrupt (except on intel ce4100).
2385 * get_link_status will stay false until the
2386 * e1000_check_for_link establishes link for copper adapters
2389 switch (hw->media_type) {
2390 case e1000_media_type_copper:
2391 if (hw->mac_type == e1000_ce4100)
2392 hw->get_link_status = 1;
2393 if (hw->get_link_status) {
2394 e1000_check_for_link(hw);
2395 link_active = !hw->get_link_status;
2400 case e1000_media_type_fiber:
2401 e1000_check_for_link(hw);
2402 link_active = !!(er32(STATUS) & E1000_STATUS_LU);
2404 case e1000_media_type_internal_serdes:
2405 e1000_check_for_link(hw);
2406 link_active = hw->serdes_has_link;
2416 * e1000_watchdog - work function
2417 * @work: work struct contained inside adapter struct
2419 static void e1000_watchdog(struct work_struct *work)
2421 struct e1000_adapter *adapter = container_of(work,
2422 struct e1000_adapter,
2423 watchdog_task.work);
2424 struct e1000_hw *hw = &adapter->hw;
2425 struct net_device *netdev = adapter->netdev;
2426 struct e1000_tx_ring *txdr = adapter->tx_ring;
2429 link = e1000_has_link(adapter);
2430 if ((netif_carrier_ok(netdev)) && link)
2434 if (!netif_carrier_ok(netdev)) {
2436 /* update snapshot of PHY registers on LSC */
2437 e1000_get_speed_and_duplex(hw,
2438 &adapter->link_speed,
2439 &adapter->link_duplex);
2442 pr_info("%s NIC Link is Up %d Mbps %s, "
2443 "Flow Control: %s\n",
2445 adapter->link_speed,
2446 adapter->link_duplex == FULL_DUPLEX ?
2447 "Full Duplex" : "Half Duplex",
2448 ((ctrl & E1000_CTRL_TFCE) && (ctrl &
2449 E1000_CTRL_RFCE)) ? "RX/TX" : ((ctrl &
2450 E1000_CTRL_RFCE) ? "RX" : ((ctrl &
2451 E1000_CTRL_TFCE) ? "TX" : "None")));
2453 /* adjust timeout factor according to speed/duplex */
2454 adapter->tx_timeout_factor = 1;
2455 switch (adapter->link_speed) {
2457 adapter->tx_timeout_factor = 16;
2460 /* maybe add some timeout factor ? */
2464 /* enable transmits in the hardware */
2466 tctl |= E1000_TCTL_EN;
2469 netif_carrier_on(netdev);
2470 if (!test_bit(__E1000_DOWN, &adapter->flags))
2471 schedule_delayed_work(&adapter->phy_info_task,
2473 adapter->smartspeed = 0;
2476 if (netif_carrier_ok(netdev)) {
2477 adapter->link_speed = 0;
2478 adapter->link_duplex = 0;
2479 pr_info("%s NIC Link is Down\n",
2481 netif_carrier_off(netdev);
2483 if (!test_bit(__E1000_DOWN, &adapter->flags))
2484 schedule_delayed_work(&adapter->phy_info_task,
2488 e1000_smartspeed(adapter);
2492 e1000_update_stats(adapter);
2494 hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
2495 adapter->tpt_old = adapter->stats.tpt;
2496 hw->collision_delta = adapter->stats.colc - adapter->colc_old;
2497 adapter->colc_old = adapter->stats.colc;
2499 adapter->gorcl = adapter->stats.gorcl - adapter->gorcl_old;
2500 adapter->gorcl_old = adapter->stats.gorcl;
2501 adapter->gotcl = adapter->stats.gotcl - adapter->gotcl_old;
2502 adapter->gotcl_old = adapter->stats.gotcl;
2504 e1000_update_adaptive(hw);
2506 if (!netif_carrier_ok(netdev)) {
2507 if (E1000_DESC_UNUSED(txdr) + 1 < txdr->count) {
2508 /* We've lost link, so the controller stops DMA,
2509 * but we've got queued Tx work that's never going
2510 * to get done, so reset controller to flush Tx.
2511 * (Do the reset outside of interrupt context).
2513 adapter->tx_timeout_count++;
2514 schedule_work(&adapter->reset_task);
2515 /* exit immediately since reset is imminent */
2520 /* Simple mode for Interrupt Throttle Rate (ITR) */
2521 if (hw->mac_type >= e1000_82540 && adapter->itr_setting == 4) {
2522 /* Symmetric Tx/Rx gets a reduced ITR=2000;
2523 * Total asymmetrical Tx or Rx gets ITR=8000;
2524 * everyone else is between 2000-8000.
2526 u32 goc = (adapter->gotcl + adapter->gorcl) / 10000;
2527 u32 dif = (adapter->gotcl > adapter->gorcl ?
2528 adapter->gotcl - adapter->gorcl :
2529 adapter->gorcl - adapter->gotcl) / 10000;
2530 u32 itr = goc > 0 ? (dif * 6000 / goc + 2000) : 8000;
2532 ew32(ITR, 1000000000 / (itr * 256));
2535 /* Cause software interrupt to ensure rx ring is cleaned */
2536 ew32(ICS, E1000_ICS_RXDMT0);
2538 /* Force detection of hung controller every watchdog period */
2539 adapter->detect_tx_hung = true;
2541 /* Reschedule the task */
2542 if (!test_bit(__E1000_DOWN, &adapter->flags))
2543 schedule_delayed_work(&adapter->watchdog_task, 2 * HZ);
2546 enum latency_range {
2550 latency_invalid = 255
2554 * e1000_update_itr - update the dynamic ITR value based on statistics
2555 * @adapter: pointer to adapter
2556 * @itr_setting: current adapter->itr
2557 * @packets: the number of packets during this measurement interval
2558 * @bytes: the number of bytes during this measurement interval
2560 * Stores a new ITR value based on packets and byte
2561 * counts during the last interrupt. The advantage of per interrupt
2562 * computation is faster updates and more accurate ITR for the current
2563 * traffic pattern. Constants in this function were computed
2564 * based on theoretical maximum wire speed and thresholds were set based
2565 * on testing data as well as attempting to minimize response time
2566 * while increasing bulk throughput.
2567 * this functionality is controlled by the InterruptThrottleRate module
2568 * parameter (see e1000_param.c)
2570 static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
2571 u16 itr_setting, int packets, int bytes)
2573 unsigned int retval = itr_setting;
2574 struct e1000_hw *hw = &adapter->hw;
2576 if (unlikely(hw->mac_type < e1000_82540))
2577 goto update_itr_done;
2580 goto update_itr_done;
2582 switch (itr_setting) {
2583 case lowest_latency:
2584 /* jumbo frames get bulk treatment*/
2585 if (bytes/packets > 8000)
2586 retval = bulk_latency;
2587 else if ((packets < 5) && (bytes > 512))
2588 retval = low_latency;
2590 case low_latency: /* 50 usec aka 20000 ints/s */
2591 if (bytes > 10000) {
2592 /* jumbo frames need bulk latency setting */
2593 if (bytes/packets > 8000)
2594 retval = bulk_latency;
2595 else if ((packets < 10) || ((bytes/packets) > 1200))
2596 retval = bulk_latency;
2597 else if ((packets > 35))
2598 retval = lowest_latency;
2599 } else if (bytes/packets > 2000)
2600 retval = bulk_latency;
2601 else if (packets <= 2 && bytes < 512)
2602 retval = lowest_latency;
2604 case bulk_latency: /* 250 usec aka 4000 ints/s */
2605 if (bytes > 25000) {
2607 retval = low_latency;
2608 } else if (bytes < 6000) {
2609 retval = low_latency;
2618 static void e1000_set_itr(struct e1000_adapter *adapter)
2620 struct e1000_hw *hw = &adapter->hw;
2622 u32 new_itr = adapter->itr;
2624 if (unlikely(hw->mac_type < e1000_82540))
2627 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
2628 if (unlikely(adapter->link_speed != SPEED_1000)) {
2634 adapter->tx_itr = e1000_update_itr(adapter, adapter->tx_itr,
2635 adapter->total_tx_packets,
2636 adapter->total_tx_bytes);
2637 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2638 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
2639 adapter->tx_itr = low_latency;
2641 adapter->rx_itr = e1000_update_itr(adapter, adapter->rx_itr,
2642 adapter->total_rx_packets,
2643 adapter->total_rx_bytes);
2644 /* conservative mode (itr 3) eliminates the lowest_latency setting */
2645 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
2646 adapter->rx_itr = low_latency;
2648 current_itr = max(adapter->rx_itr, adapter->tx_itr);
2650 switch (current_itr) {
2651 /* counts and packets in update_itr are dependent on these numbers */
2652 case lowest_latency:
2656 new_itr = 20000; /* aka hwitr = ~200 */
2666 if (new_itr != adapter->itr) {
2667 /* this attempts to bias the interrupt rate towards Bulk
2668 * by adding intermediate steps when interrupt rate is
2671 new_itr = new_itr > adapter->itr ?
2672 min(adapter->itr + (new_itr >> 2), new_itr) :
2674 adapter->itr = new_itr;
2675 ew32(ITR, 1000000000 / (new_itr * 256));
2679 #define E1000_TX_FLAGS_CSUM 0x00000001
2680 #define E1000_TX_FLAGS_VLAN 0x00000002
2681 #define E1000_TX_FLAGS_TSO 0x00000004
2682 #define E1000_TX_FLAGS_IPV4 0x00000008
2683 #define E1000_TX_FLAGS_NO_FCS 0x00000010
2684 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
2685 #define E1000_TX_FLAGS_VLAN_SHIFT 16
2687 static int e1000_tso(struct e1000_adapter *adapter,
2688 struct e1000_tx_ring *tx_ring, struct sk_buff *skb,
2691 struct e1000_context_desc *context_desc;
2692 struct e1000_tx_buffer *buffer_info;
2695 u16 ipcse = 0, tucse, mss;
2696 u8 ipcss, ipcso, tucss, tucso, hdr_len;
2698 if (skb_is_gso(skb)) {
2701 err = skb_cow_head(skb, 0);
2705 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
2706 mss = skb_shinfo(skb)->gso_size;
2707 if (protocol == htons(ETH_P_IP)) {
2708 struct iphdr *iph = ip_hdr(skb);
2711 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
2715 cmd_length = E1000_TXD_CMD_IP;
2716 ipcse = skb_transport_offset(skb) - 1;
2717 } else if (skb_is_gso_v6(skb)) {
2718 ipv6_hdr(skb)->payload_len = 0;
2719 tcp_hdr(skb)->check =
2720 ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
2721 &ipv6_hdr(skb)->daddr,
2725 ipcss = skb_network_offset(skb);
2726 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
2727 tucss = skb_transport_offset(skb);
2728 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
2731 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
2732 E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
2734 i = tx_ring->next_to_use;
2735 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
2736 buffer_info = &tx_ring->buffer_info[i];
2738 context_desc->lower_setup.ip_fields.ipcss = ipcss;
2739 context_desc->lower_setup.ip_fields.ipcso = ipcso;
2740 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
2741 context_desc->upper_setup.tcp_fields.tucss = tucss;
2742 context_desc->upper_setup.tcp_fields.tucso = tucso;
2743 context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
2744 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
2745 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
2746 context_desc->cmd_and_length = cpu_to_le32(cmd_length);
2748 buffer_info->time_stamp = jiffies;
2749 buffer_info->next_to_watch = i;
2751 if (++i == tx_ring->count)
2754 tx_ring->next_to_use = i;
2761 static bool e1000_tx_csum(struct e1000_adapter *adapter,
2762 struct e1000_tx_ring *tx_ring, struct sk_buff *skb,
2765 struct e1000_context_desc *context_desc;
2766 struct e1000_tx_buffer *buffer_info;
2769 u32 cmd_len = E1000_TXD_CMD_DEXT;
2771 if (skb->ip_summed != CHECKSUM_PARTIAL)
2775 case cpu_to_be16(ETH_P_IP):
2776 if (ip_hdr(skb)->protocol == IPPROTO_TCP)
2777 cmd_len |= E1000_TXD_CMD_TCP;
2779 case cpu_to_be16(ETH_P_IPV6):
2780 /* XXX not handling all IPV6 headers */
2781 if (ipv6_hdr(skb)->nexthdr == IPPROTO_TCP)
2782 cmd_len |= E1000_TXD_CMD_TCP;
2785 if (unlikely(net_ratelimit()))
2786 e_warn(drv, "checksum_partial proto=%x!\n",
2791 css = skb_checksum_start_offset(skb);
2793 i = tx_ring->next_to_use;
2794 buffer_info = &tx_ring->buffer_info[i];
2795 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
2797 context_desc->lower_setup.ip_config = 0;
2798 context_desc->upper_setup.tcp_fields.tucss = css;
2799 context_desc->upper_setup.tcp_fields.tucso =
2800 css + skb->csum_offset;
2801 context_desc->upper_setup.tcp_fields.tucse = 0;
2802 context_desc->tcp_seg_setup.data = 0;
2803 context_desc->cmd_and_length = cpu_to_le32(cmd_len);
2805 buffer_info->time_stamp = jiffies;
2806 buffer_info->next_to_watch = i;
2808 if (unlikely(++i == tx_ring->count))
2811 tx_ring->next_to_use = i;
2816 #define E1000_MAX_TXD_PWR 12
2817 #define E1000_MAX_DATA_PER_TXD (1<<E1000_MAX_TXD_PWR)
2819 static int e1000_tx_map(struct e1000_adapter *adapter,
2820 struct e1000_tx_ring *tx_ring,
2821 struct sk_buff *skb, unsigned int first,
2822 unsigned int max_per_txd, unsigned int nr_frags,
2825 struct e1000_hw *hw = &adapter->hw;
2826 struct pci_dev *pdev = adapter->pdev;
2827 struct e1000_tx_buffer *buffer_info;
2828 unsigned int len = skb_headlen(skb);
2829 unsigned int offset = 0, size, count = 0, i;
2830 unsigned int f, bytecount, segs;
2832 i = tx_ring->next_to_use;
2835 buffer_info = &tx_ring->buffer_info[i];
2836 size = min(len, max_per_txd);
2837 /* Workaround for Controller erratum --
2838 * descriptor for non-tso packet in a linear SKB that follows a
2839 * tso gets written back prematurely before the data is fully
2840 * DMA'd to the controller
2842 if (!skb->data_len && tx_ring->last_tx_tso &&
2844 tx_ring->last_tx_tso = false;
2848 /* Workaround for premature desc write-backs
2849 * in TSO mode. Append 4-byte sentinel desc
2851 if (unlikely(mss && !nr_frags && size == len && size > 8))
2853 /* work-around for errata 10 and it applies
2854 * to all controllers in PCI-X mode
2855 * The fix is to make sure that the first descriptor of a
2856 * packet is smaller than 2048 - 16 - 16 (or 2016) bytes
2858 if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
2859 (size > 2015) && count == 0))
2862 /* Workaround for potential 82544 hang in PCI-X. Avoid
2863 * terminating buffers within evenly-aligned dwords.
2865 if (unlikely(adapter->pcix_82544 &&
2866 !((unsigned long)(skb->data + offset + size - 1) & 4) &&
2870 buffer_info->length = size;
2871 /* set time_stamp *before* dma to help avoid a possible race */
2872 buffer_info->time_stamp = jiffies;
2873 buffer_info->mapped_as_page = false;
2874 buffer_info->dma = dma_map_single(&pdev->dev,
2876 size, DMA_TO_DEVICE);
2877 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
2879 buffer_info->next_to_watch = i;
2886 if (unlikely(i == tx_ring->count))
2891 for (f = 0; f < nr_frags; f++) {
2892 const struct skb_frag_struct *frag;
2894 frag = &skb_shinfo(skb)->frags[f];
2895 len = skb_frag_size(frag);
2899 unsigned long bufend;
2901 if (unlikely(i == tx_ring->count))
2904 buffer_info = &tx_ring->buffer_info[i];
2905 size = min(len, max_per_txd);
2906 /* Workaround for premature desc write-backs
2907 * in TSO mode. Append 4-byte sentinel desc
2909 if (unlikely(mss && f == (nr_frags-1) &&
2910 size == len && size > 8))
2912 /* Workaround for potential 82544 hang in PCI-X.
2913 * Avoid terminating buffers within evenly-aligned
2916 bufend = (unsigned long)
2917 page_to_phys(skb_frag_page(frag));
2918 bufend += offset + size - 1;
2919 if (unlikely(adapter->pcix_82544 &&
2924 buffer_info->length = size;
2925 buffer_info->time_stamp = jiffies;
2926 buffer_info->mapped_as_page = true;
2927 buffer_info->dma = skb_frag_dma_map(&pdev->dev, frag,
2928 offset, size, DMA_TO_DEVICE);
2929 if (dma_mapping_error(&pdev->dev, buffer_info->dma))
2931 buffer_info->next_to_watch = i;
2939 segs = skb_shinfo(skb)->gso_segs ?: 1;
2940 /* multiply data chunks by size of headers */
2941 bytecount = ((segs - 1) * skb_headlen(skb)) + skb->len;
2943 tx_ring->buffer_info[i].skb = skb;
2944 tx_ring->buffer_info[i].segs = segs;
2945 tx_ring->buffer_info[i].bytecount = bytecount;
2946 tx_ring->buffer_info[first].next_to_watch = i;
2951 dev_err(&pdev->dev, "TX DMA map failed\n");
2952 buffer_info->dma = 0;
2958 i += tx_ring->count;
2960 buffer_info = &tx_ring->buffer_info[i];
2961 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
2967 static void e1000_tx_queue(struct e1000_adapter *adapter,
2968 struct e1000_tx_ring *tx_ring, int tx_flags,
2971 struct e1000_tx_desc *tx_desc = NULL;
2972 struct e1000_tx_buffer *buffer_info;
2973 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
2976 if (likely(tx_flags & E1000_TX_FLAGS_TSO)) {
2977 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
2979 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
2981 if (likely(tx_flags & E1000_TX_FLAGS_IPV4))
2982 txd_upper |= E1000_TXD_POPTS_IXSM << 8;
2985 if (likely(tx_flags & E1000_TX_FLAGS_CSUM)) {
2986 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
2987 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
2990 if (unlikely(tx_flags & E1000_TX_FLAGS_VLAN)) {
2991 txd_lower |= E1000_TXD_CMD_VLE;
2992 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
2995 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
2996 txd_lower &= ~(E1000_TXD_CMD_IFCS);
2998 i = tx_ring->next_to_use;
3001 buffer_info = &tx_ring->buffer_info[i];
3002 tx_desc = E1000_TX_DESC(*tx_ring, i);
3003 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
3004 tx_desc->lower.data =
3005 cpu_to_le32(txd_lower | buffer_info->length);
3006 tx_desc->upper.data = cpu_to_le32(txd_upper);
3007 if (unlikely(++i == tx_ring->count))
3011 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
3013 /* txd_cmd re-enables FCS, so we'll re-disable it here as desired. */
3014 if (unlikely(tx_flags & E1000_TX_FLAGS_NO_FCS))
3015 tx_desc->lower.data &= ~(cpu_to_le32(E1000_TXD_CMD_IFCS));
3017 /* Force memory writes to complete before letting h/w
3018 * know there are new descriptors to fetch. (Only
3019 * applicable for weak-ordered memory model archs,
3024 tx_ring->next_to_use = i;
3027 /* 82547 workaround to avoid controller hang in half-duplex environment.
3028 * The workaround is to avoid queuing a large packet that would span
3029 * the internal Tx FIFO ring boundary by notifying the stack to resend
3030 * the packet at a later time. This gives the Tx FIFO an opportunity to
3031 * flush all packets. When that occurs, we reset the Tx FIFO pointers
3032 * to the beginning of the Tx FIFO.
3035 #define E1000_FIFO_HDR 0x10
3036 #define E1000_82547_PAD_LEN 0x3E0
3038 static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter,
3039 struct sk_buff *skb)
3041 u32 fifo_space = adapter->tx_fifo_size - adapter->tx_fifo_head;
3042 u32 skb_fifo_len = skb->len + E1000_FIFO_HDR;
3044 skb_fifo_len = ALIGN(skb_fifo_len, E1000_FIFO_HDR);
3046 if (adapter->link_duplex != HALF_DUPLEX)
3047 goto no_fifo_stall_required;
3049 if (atomic_read(&adapter->tx_fifo_stall))
3052 if (skb_fifo_len >= (E1000_82547_PAD_LEN + fifo_space)) {
3053 atomic_set(&adapter->tx_fifo_stall, 1);
3057 no_fifo_stall_required:
3058 adapter->tx_fifo_head += skb_fifo_len;
3059 if (adapter->tx_fifo_head >= adapter->tx_fifo_size)
3060 adapter->tx_fifo_head -= adapter->tx_fifo_size;
3064 static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
3066 struct e1000_adapter *adapter = netdev_priv(netdev);
3067 struct e1000_tx_ring *tx_ring = adapter->tx_ring;
3069 netif_stop_queue(netdev);
3070 /* Herbert's original patch had:
3071 * smp_mb__after_netif_stop_queue();
3072 * but since that doesn't exist yet, just open code it.
3076 /* We need to check again in a case another CPU has just
3077 * made room available.
3079 if (likely(E1000_DESC_UNUSED(tx_ring) < size))
3083 netif_start_queue(netdev);
3084 ++adapter->restart_queue;
3088 static int e1000_maybe_stop_tx(struct net_device *netdev,
3089 struct e1000_tx_ring *tx_ring, int size)
3091 if (likely(E1000_DESC_UNUSED(tx_ring) >= size))
3093 return __e1000_maybe_stop_tx(netdev, size);
3096 #define TXD_USE_COUNT(S, X) (((S) + ((1 << (X)) - 1)) >> (X))
3097 static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb,
3098 struct net_device *netdev)
3100 struct e1000_adapter *adapter = netdev_priv(netdev);
3101 struct e1000_hw *hw = &adapter->hw;
3102 struct e1000_tx_ring *tx_ring;
3103 unsigned int first, max_per_txd = E1000_MAX_DATA_PER_TXD;
3104 unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
3105 unsigned int tx_flags = 0;
3106 unsigned int len = skb_headlen(skb);
3107 unsigned int nr_frags;
3112 __be16 protocol = vlan_get_protocol(skb);
3114 /* This goes back to the question of how to logically map a Tx queue
3115 * to a flow. Right now, performance is impacted slightly negatively
3116 * if using multiple Tx queues. If the stack breaks away from a
3117 * single qdisc implementation, we can look at this again.
3119 tx_ring = adapter->tx_ring;
3121 /* On PCI/PCI-X HW, if packet size is less than ETH_ZLEN,
3122 * packets may get corrupted during padding by HW.
3123 * To WA this issue, pad all small packets manually.
3125 if (eth_skb_pad(skb))
3126 return NETDEV_TX_OK;
3128 mss = skb_shinfo(skb)->gso_size;
3129 /* The controller does a simple calculation to
3130 * make sure there is enough room in the FIFO before
3131 * initiating the DMA for each buffer. The calc is:
3132 * 4 = ceil(buffer len/mss). To make sure we don't
3133 * overrun the FIFO, adjust the max buffer len if mss
3138 max_per_txd = min(mss << 2, max_per_txd);
3139 max_txd_pwr = fls(max_per_txd) - 1;
3141 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
3142 if (skb->data_len && hdr_len == len) {
3143 switch (hw->mac_type) {
3144 unsigned int pull_size;
3146 /* Make sure we have room to chop off 4 bytes,
3147 * and that the end alignment will work out to
3148 * this hardware's requirements
3149 * NOTE: this is a TSO only workaround
3150 * if end byte alignment not correct move us
3151 * into the next dword
3153 if ((unsigned long)(skb_tail_pointer(skb) - 1)
3157 pull_size = min((unsigned int)4, skb->data_len);
3158 if (!__pskb_pull_tail(skb, pull_size)) {
3159 e_err(drv, "__pskb_pull_tail "
3161 dev_kfree_skb_any(skb);
3162 return NETDEV_TX_OK;
3164 len = skb_headlen(skb);
3173 /* reserve a descriptor for the offload context */
3174 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
3178 /* Controller Erratum workaround */
3179 if (!skb->data_len && tx_ring->last_tx_tso && !skb_is_gso(skb))
3182 count += TXD_USE_COUNT(len, max_txd_pwr);
3184 if (adapter->pcix_82544)
3187 /* work-around for errata 10 and it applies to all controllers
3188 * in PCI-X mode, so add one more descriptor to the count
3190 if (unlikely((hw->bus_type == e1000_bus_type_pcix) &&
3194 nr_frags = skb_shinfo(skb)->nr_frags;
3195 for (f = 0; f < nr_frags; f++)
3196 count += TXD_USE_COUNT(skb_frag_size(&skb_shinfo(skb)->frags[f]),
3198 if (adapter->pcix_82544)
3201 /* need: count + 2 desc gap to keep tail from touching
3202 * head, otherwise try next time
3204 if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2)))
3205 return NETDEV_TX_BUSY;
3207 if (unlikely((hw->mac_type == e1000_82547) &&
3208 (e1000_82547_fifo_workaround(adapter, skb)))) {
3209 netif_stop_queue(netdev);
3210 if (!test_bit(__E1000_DOWN, &adapter->flags))
3211 schedule_delayed_work(&adapter->fifo_stall_task, 1);
3212 return NETDEV_TX_BUSY;
3215 if (skb_vlan_tag_present(skb)) {
3216 tx_flags |= E1000_TX_FLAGS_VLAN;
3217 tx_flags |= (skb_vlan_tag_get(skb) <<
3218 E1000_TX_FLAGS_VLAN_SHIFT);
3221 first = tx_ring->next_to_use;
3223 tso = e1000_tso(adapter, tx_ring, skb, protocol);
3225 dev_kfree_skb_any(skb);
3226 return NETDEV_TX_OK;
3230 if (likely(hw->mac_type != e1000_82544))
3231 tx_ring->last_tx_tso = true;
3232 tx_flags |= E1000_TX_FLAGS_TSO;
3233 } else if (likely(e1000_tx_csum(adapter, tx_ring, skb, protocol)))
3234 tx_flags |= E1000_TX_FLAGS_CSUM;
3236 if (protocol == htons(ETH_P_IP))
3237 tx_flags |= E1000_TX_FLAGS_IPV4;
3239 if (unlikely(skb->no_fcs))
3240 tx_flags |= E1000_TX_FLAGS_NO_FCS;
3242 count = e1000_tx_map(adapter, tx_ring, skb, first, max_per_txd,
3246 /* The descriptors needed is higher than other Intel drivers
3247 * due to a number of workarounds. The breakdown is below:
3248 * Data descriptors: MAX_SKB_FRAGS + 1
3249 * Context Descriptor: 1
3250 * Keep head from touching tail: 2
3253 int desc_needed = MAX_SKB_FRAGS + 7;
3255 netdev_sent_queue(netdev, skb->len);
3256 skb_tx_timestamp(skb);
3258 e1000_tx_queue(adapter, tx_ring, tx_flags, count);
3260 /* 82544 potentially requires twice as many data descriptors
3261 * in order to guarantee buffers don't end on evenly-aligned
3264 if (adapter->pcix_82544)
3265 desc_needed += MAX_SKB_FRAGS + 1;
3267 /* Make sure there is space in the ring for the next send. */
3268 e1000_maybe_stop_tx(netdev, tx_ring, desc_needed);
3270 if (!skb->xmit_more ||
3271 netif_xmit_stopped(netdev_get_tx_queue(netdev, 0))) {
3272 writel(tx_ring->next_to_use, hw->hw_addr + tx_ring->tdt);
3273 /* we need this if more than one processor can write to
3274 * our tail at a time, it synchronizes IO on IA64/Altix
3280 dev_kfree_skb_any(skb);
3281 tx_ring->buffer_info[first].time_stamp = 0;
3282 tx_ring->next_to_use = first;
3285 return NETDEV_TX_OK;
3288 #define NUM_REGS 38 /* 1 based count */
3289 static void e1000_regdump(struct e1000_adapter *adapter)
3291 struct e1000_hw *hw = &adapter->hw;
3293 u32 *regs_buff = regs;
3296 static const char * const reg_name[] = {
3298 "RCTL", "RDLEN", "RDH", "RDT", "RDTR",
3299 "TCTL", "TDBAL", "TDBAH", "TDLEN", "TDH", "TDT",
3300 "TIDV", "TXDCTL", "TADV", "TARC0",
3301 "TDBAL1", "TDBAH1", "TDLEN1", "TDH1", "TDT1",
3303 "CTRL_EXT", "ERT", "RDBAL", "RDBAH",
3304 "TDFH", "TDFT", "TDFHS", "TDFTS", "TDFPC",
3305 "RDFH", "RDFT", "RDFHS", "RDFTS", "RDFPC"
3308 regs_buff[0] = er32(CTRL);
3309 regs_buff[1] = er32(STATUS);
3311 regs_buff[2] = er32(RCTL);
3312 regs_buff[3] = er32(RDLEN);
3313 regs_buff[4] = er32(RDH);
3314 regs_buff[5] = er32(RDT);
3315 regs_buff[6] = er32(RDTR);
3317 regs_buff[7] = er32(TCTL);
3318 regs_buff[8] = er32(TDBAL);
3319 regs_buff[9] = er32(TDBAH);
3320 regs_buff[10] = er32(TDLEN);
3321 regs_buff[11] = er32(TDH);
3322 regs_buff[12] = er32(TDT);
3323 regs_buff[13] = er32(TIDV);
3324 regs_buff[14] = er32(TXDCTL);
3325 regs_buff[15] = er32(TADV);
3326 regs_buff[16] = er32(TARC0);
3328 regs_buff[17] = er32(TDBAL1);
3329 regs_buff[18] = er32(TDBAH1);
3330 regs_buff[19] = er32(TDLEN1);
3331 regs_buff[20] = er32(TDH1);
3332 regs_buff[21] = er32(TDT1);
3333 regs_buff[22] = er32(TXDCTL1);
3334 regs_buff[23] = er32(TARC1);
3335 regs_buff[24] = er32(CTRL_EXT);
3336 regs_buff[25] = er32(ERT);
3337 regs_buff[26] = er32(RDBAL0);
3338 regs_buff[27] = er32(RDBAH0);
3339 regs_buff[28] = er32(TDFH);
3340 regs_buff[29] = er32(TDFT);
3341 regs_buff[30] = er32(TDFHS);
3342 regs_buff[31] = er32(TDFTS);
3343 regs_buff[32] = er32(TDFPC);
3344 regs_buff[33] = er32(RDFH);
3345 regs_buff[34] = er32(RDFT);
3346 regs_buff[35] = er32(RDFHS);
3347 regs_buff[36] = er32(RDFTS);
3348 regs_buff[37] = er32(RDFPC);
3350 pr_info("Register dump\n");
3351 for (i = 0; i < NUM_REGS; i++)
3352 pr_info("%-15s %08x\n", reg_name[i], regs_buff[i]);
3356 * e1000_dump: Print registers, tx ring and rx ring
3358 static void e1000_dump(struct e1000_adapter *adapter)
3360 /* this code doesn't handle multiple rings */
3361 struct e1000_tx_ring *tx_ring = adapter->tx_ring;
3362 struct e1000_rx_ring *rx_ring = adapter->rx_ring;
3365 if (!netif_msg_hw(adapter))
3368 /* Print Registers */
3369 e1000_regdump(adapter);
3372 pr_info("TX Desc ring0 dump\n");
3374 /* Transmit Descriptor Formats - DEXT[29] is 0 (Legacy) or 1 (Extended)
3376 * Legacy Transmit Descriptor
3377 * +--------------------------------------------------------------+
3378 * 0 | Buffer Address [63:0] (Reserved on Write Back) |
3379 * +--------------------------------------------------------------+
3380 * 8 | Special | CSS | Status | CMD | CSO | Length |
3381 * +--------------------------------------------------------------+
3382 * 63 48 47 36 35 32 31 24 23 16 15 0
3384 * Extended Context Descriptor (DTYP=0x0) for TSO or checksum offload
3385 * 63 48 47 40 39 32 31 16 15 8 7 0
3386 * +----------------------------------------------------------------+
3387 * 0 | TUCSE | TUCS0 | TUCSS | IPCSE | IPCS0 | IPCSS |
3388 * +----------------------------------------------------------------+
3389 * 8 | MSS | HDRLEN | RSV | STA | TUCMD | DTYP | PAYLEN |
3390 * +----------------------------------------------------------------+
3391 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
3393 * Extended Data Descriptor (DTYP=0x1)
3394 * +----------------------------------------------------------------+
3395 * 0 | Buffer Address [63:0] |
3396 * +----------------------------------------------------------------+
3397 * 8 | VLAN tag | POPTS | Rsvd | Status | Command | DTYP | DTALEN |
3398 * +----------------------------------------------------------------+
3399 * 63 48 47 40 39 36 35 32 31 24 23 20 19 0
3401 pr_info("Tc[desc] [Ce CoCsIpceCoS] [MssHlRSCm0Plen] [bi->dma ] leng ntw timestmp bi->skb\n");
3402 pr_info("Td[desc] [address 63:0 ] [VlaPoRSCm1Dlen] [bi->dma ] leng ntw timestmp bi->skb\n");
3404 if (!netif_msg_tx_done(adapter))
3405 goto rx_ring_summary;
3407 for (i = 0; tx_ring->desc && (i < tx_ring->count); i++) {
3408 struct e1000_tx_desc *tx_desc = E1000_TX_DESC(*tx_ring, i);
3409 struct e1000_tx_buffer *buffer_info = &tx_ring->buffer_info[i];
3410 struct my_u { __le64 a; __le64 b; };
3411 struct my_u *u = (struct my_u *)tx_desc;
3414 if (i == tx_ring->next_to_use && i == tx_ring->next_to_clean)
3416 else if (i == tx_ring->next_to_use)
3418 else if (i == tx_ring->next_to_clean)
3423 pr_info("T%c[0x%03X] %016llX %016llX %016llX %04X %3X %016llX %p %s\n",
3424 ((le64_to_cpu(u->b) & (1<<20)) ? 'd' : 'c'), i,
3425 le64_to_cpu(u->a), le64_to_cpu(u->b),
3426 (u64)buffer_info->dma, buffer_info->length,
3427 buffer_info->next_to_watch,
3428 (u64)buffer_info->time_stamp, buffer_info->skb, type);
3433 pr_info("\nRX Desc ring dump\n");
3435 /* Legacy Receive Descriptor Format
3437 * +-----------------------------------------------------+
3438 * | Buffer Address [63:0] |
3439 * +-----------------------------------------------------+
3440 * | VLAN Tag | Errors | Status 0 | Packet csum | Length |
3441 * +-----------------------------------------------------+
3442 * 63 48 47 40 39 32 31 16 15 0
3444 pr_info("R[desc] [address 63:0 ] [vl er S cks ln] [bi->dma ] [bi->skb]\n");
3446 if (!netif_msg_rx_status(adapter))
3449 for (i = 0; rx_ring->desc && (i < rx_ring->count); i++) {
3450 struct e1000_rx_desc *rx_desc = E1000_RX_DESC(*rx_ring, i);
3451 struct e1000_rx_buffer *buffer_info = &rx_ring->buffer_info[i];
3452 struct my_u { __le64 a; __le64 b; };
3453 struct my_u *u = (struct my_u *)rx_desc;
3456 if (i == rx_ring->next_to_use)
3458 else if (i == rx_ring->next_to_clean)
3463 pr_info("R[0x%03X] %016llX %016llX %016llX %p %s\n",
3464 i, le64_to_cpu(u->a), le64_to_cpu(u->b),
3465 (u64)buffer_info->dma, buffer_info->rxbuf.data, type);
3468 /* dump the descriptor caches */
3470 pr_info("Rx descriptor cache in 64bit format\n");
3471 for (i = 0x6000; i <= 0x63FF ; i += 0x10) {
3472 pr_info("R%04X: %08X|%08X %08X|%08X\n",
3474 readl(adapter->hw.hw_addr + i+4),
3475 readl(adapter->hw.hw_addr + i),
3476 readl(adapter->hw.hw_addr + i+12),
3477 readl(adapter->hw.hw_addr + i+8));
3480 pr_info("Tx descriptor cache in 64bit format\n");
3481 for (i = 0x7000; i <= 0x73FF ; i += 0x10) {
3482 pr_info("T%04X: %08X|%08X %08X|%08X\n",
3484 readl(adapter->hw.hw_addr + i+4),
3485 readl(adapter->hw.hw_addr + i),
3486 readl(adapter->hw.hw_addr + i+12),
3487 readl(adapter->hw.hw_addr + i+8));
3494 * e1000_tx_timeout - Respond to a Tx Hang
3495 * @netdev: network interface device structure
3497 static void e1000_tx_timeout(struct net_device *netdev)
3499 struct e1000_adapter *adapter = netdev_priv(netdev);
3501 /* Do the reset outside of interrupt context */
3502 adapter->tx_timeout_count++;
3503 schedule_work(&adapter->reset_task);
3506 static void e1000_reset_task(struct work_struct *work)
3508 struct e1000_adapter *adapter =
3509 container_of(work, struct e1000_adapter, reset_task);
3511 e_err(drv, "Reset adapter\n");
3512 e1000_reinit_locked(adapter);
3516 * e1000_change_mtu - Change the Maximum Transfer Unit
3517 * @netdev: network interface device structure
3518 * @new_mtu: new value for maximum frame size
3520 * Returns 0 on success, negative on failure
3522 static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
3524 struct e1000_adapter *adapter = netdev_priv(netdev);
3525 struct e1000_hw *hw = &adapter->hw;
3526 int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
3528 /* Adapter-specific max frame size limits. */
3529 switch (hw->mac_type) {
3530 case e1000_undefined ... e1000_82542_rev2_1:
3531 if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) {
3532 e_err(probe, "Jumbo Frames not supported.\n");
3537 /* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */
3541 while (test_and_set_bit(__E1000_RESETTING, &adapter->flags))
3543 /* e1000_down has a dependency on max_frame_size */
3544 hw->max_frame_size = max_frame;
3545 if (netif_running(netdev)) {
3546 /* prevent buffers from being reallocated */
3547 adapter->alloc_rx_buf = e1000_alloc_dummy_rx_buffers;
3548 e1000_down(adapter);
3551 /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
3552 * means we reserve 2 more, this pushes us to allocate from the next
3554 * i.e. RXBUFFER_2048 --> size-4096 slab
3555 * however with the new *_jumbo_rx* routines, jumbo receives will use
3559 if (max_frame <= E1000_RXBUFFER_2048)
3560 adapter->rx_buffer_len = E1000_RXBUFFER_2048;
3562 #if (PAGE_SIZE >= E1000_RXBUFFER_16384)
3563 adapter->rx_buffer_len = E1000_RXBUFFER_16384;
3564 #elif (PAGE_SIZE >= E1000_RXBUFFER_4096)
3565 adapter->rx_buffer_len = PAGE_SIZE;
3568 /* adjust allocation if LPE protects us, and we aren't using SBP */
3569 if (!hw->tbi_compatibility_on &&
3570 ((max_frame == (ETH_FRAME_LEN + ETH_FCS_LEN)) ||
3571 (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE)))
3572 adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE;
3574 pr_info("%s changing MTU from %d to %d\n",
3575 netdev->name, netdev->mtu, new_mtu);
3576 netdev->mtu = new_mtu;
3578 if (netif_running(netdev))
3581 e1000_reset(adapter);
3583 clear_bit(__E1000_RESETTING, &adapter->flags);
3589 * e1000_update_stats - Update the board statistics counters
3590 * @adapter: board private structure
3592 void e1000_update_stats(struct e1000_adapter *adapter)
3594 struct net_device *netdev = adapter->netdev;
3595 struct e1000_hw *hw = &adapter->hw;
3596 struct pci_dev *pdev = adapter->pdev;
3597 unsigned long flags;
3600 #define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
3602 /* Prevent stats update while adapter is being reset, or if the pci
3603 * connection is down.
3605 if (adapter->link_speed == 0)
3607 if (pci_channel_offline(pdev))
3610 spin_lock_irqsave(&adapter->stats_lock, flags);
3612 /* these counters are modified from e1000_tbi_adjust_stats,
3613 * called from the interrupt context, so they must only
3614 * be written while holding adapter->stats_lock
3617 adapter->stats.crcerrs += er32(CRCERRS);
3618 adapter->stats.gprc += er32(GPRC);
3619 adapter->stats.gorcl += er32(GORCL);
3620 adapter->stats.gorch += er32(GORCH);
3621 adapter->stats.bprc += er32(BPRC);
3622 adapter->stats.mprc += er32(MPRC);
3623 adapter->stats.roc += er32(ROC);
3625 adapter->stats.prc64 += er32(PRC64);
3626 adapter->stats.prc127 += er32(PRC127);
3627 adapter->stats.prc255 += er32(PRC255);
3628 adapter->stats.prc511 += er32(PRC511);
3629 adapter->stats.prc1023 += er32(PRC1023);
3630 adapter->stats.prc1522 += er32(PRC1522);
3632 adapter->stats.symerrs += er32(SYMERRS);
3633 adapter->stats.mpc += er32(MPC);
3634 adapter->stats.scc += er32(SCC);
3635 adapter->stats.ecol += er32(ECOL);
3636 adapter->stats.mcc += er32(MCC);
3637 adapter->stats.latecol += er32(LATECOL);
3638 adapter->stats.dc += er32(DC);
3639 adapter->stats.sec += er32(SEC);
3640 adapter->stats.rlec += er32(RLEC);
3641 adapter->stats.xonrxc += er32(XONRXC);
3642 adapter->stats.xontxc += er32(XONTXC);
3643 adapter->stats.xoffrxc += er32(XOFFRXC);
3644 adapter->stats.xofftxc += er32(XOFFTXC);
3645 adapter->stats.fcruc += er32(FCRUC);
3646 adapter->stats.gptc += er32(GPTC);
3647 adapter->stats.gotcl += er32(GOTCL);
3648 adapter->stats.gotch += er32(GOTCH);
3649 adapter->stats.rnbc += er32(RNBC);
3650 adapter->stats.ruc += er32(RUC);
3651 adapter->stats.rfc += er32(RFC);
3652 adapter->stats.rjc += er32(RJC);
3653 adapter->stats.torl += er32(TORL);
3654 adapter->stats.torh += er32(TORH);
3655 adapter->stats.totl += er32(TOTL);
3656 adapter->stats.toth += er32(TOTH);
3657 adapter->stats.tpr += er32(TPR);
3659 adapter->stats.ptc64 += er32(PTC64);
3660 adapter->stats.ptc127 += er32(PTC127);
3661 adapter->stats.ptc255 += er32(PTC255);
3662 adapter->stats.ptc511 += er32(PTC511);
3663 adapter->stats.ptc1023 += er32(PTC1023);
3664 adapter->stats.ptc1522 += er32(PTC1522);
3666 adapter->stats.mptc += er32(MPTC);
3667 adapter->stats.bptc += er32(BPTC);
3669 /* used for adaptive IFS */
3671 hw->tx_packet_delta = er32(TPT);
3672 adapter->stats.tpt += hw->tx_packet_delta;
3673 hw->collision_delta = er32(COLC);
3674 adapter->stats.colc += hw->collision_delta;
3676 if (hw->mac_type >= e1000_82543) {
3677 adapter->stats.algnerrc += er32(ALGNERRC);
3678 adapter->stats.rxerrc += er32(RXERRC);
3679 adapter->stats.tncrs += er32(TNCRS);
3680 adapter->stats.cexterr += er32(CEXTERR);
3681 adapter->stats.tsctc += er32(TSCTC);
3682 adapter->stats.tsctfc += er32(TSCTFC);
3685 /* Fill out the OS statistics structure */
3686 netdev->stats.multicast = adapter->stats.mprc;
3687 netdev->stats.collisions = adapter->stats.colc;
3691 /* RLEC on some newer hardware can be incorrect so build
3692 * our own version based on RUC and ROC
3694 netdev->stats.rx_errors = adapter->stats.rxerrc +
3695 adapter->stats.crcerrs + adapter->stats.algnerrc +
3696 adapter->stats.ruc + adapter->stats.roc +
3697 adapter->stats.cexterr;
3698 adapter->stats.rlerrc = adapter->stats.ruc + adapter->stats.roc;
3699 netdev->stats.rx_length_errors = adapter->stats.rlerrc;
3700 netdev->stats.rx_crc_errors = adapter->stats.crcerrs;
3701 netdev->stats.rx_frame_errors = adapter->stats.algnerrc;
3702 netdev->stats.rx_missed_errors = adapter->stats.mpc;
3705 adapter->stats.txerrc = adapter->stats.ecol + adapter->stats.latecol;
3706 netdev->stats.tx_errors = adapter->stats.txerrc;
3707 netdev->stats.tx_aborted_errors = adapter->stats.ecol;
3708 netdev->stats.tx_window_errors = adapter->stats.latecol;
3709 netdev->stats.tx_carrier_errors = adapter->stats.tncrs;
3710 if (hw->bad_tx_carr_stats_fd &&
3711 adapter->link_duplex == FULL_DUPLEX) {
3712 netdev->stats.tx_carrier_errors = 0;
3713 adapter->stats.tncrs = 0;
3716 /* Tx Dropped needs to be maintained elsewhere */
3719 if (hw->media_type == e1000_media_type_copper) {
3720 if ((adapter->link_speed == SPEED_1000) &&
3721 (!e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_tmp))) {
3722 phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
3723 adapter->phy_stats.idle_errors += phy_tmp;
3726 if ((hw->mac_type <= e1000_82546) &&
3727 (hw->phy_type == e1000_phy_m88) &&
3728 !e1000_read_phy_reg(hw, M88E1000_RX_ERR_CNTR, &phy_tmp))
3729 adapter->phy_stats.receive_errors += phy_tmp;
3732 /* Management Stats */
3733 if (hw->has_smbus) {
3734 adapter->stats.mgptc += er32(MGTPTC);
3735 adapter->stats.mgprc += er32(MGTPRC);
3736 adapter->stats.mgpdc += er32(MGTPDC);
3739 spin_unlock_irqrestore(&adapter->stats_lock, flags);
3743 * e1000_intr - Interrupt Handler
3744 * @irq: interrupt number
3745 * @data: pointer to a network interface device structure
3747 static irqreturn_t e1000_intr(int irq, void *data)
3749 struct net_device *netdev = data;
3750 struct e1000_adapter *adapter = netdev_priv(netdev);
3751 struct e1000_hw *hw = &adapter->hw;
3752 u32 icr = er32(ICR);
3754 if (unlikely((!icr)))
3755 return IRQ_NONE; /* Not our interrupt */
3757 /* we might have caused the interrupt, but the above
3758 * read cleared it, and just in case the driver is
3759 * down there is nothing to do so return handled
3761 if (unlikely(test_bit(__E1000_DOWN, &adapter->flags)))
3764 if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) {
3765 hw->get_link_status = 1;
3766 /* guard against interrupt when we're going down */
3767 if (!test_bit(__E1000_DOWN, &adapter->flags))
3768 schedule_delayed_work(&adapter->watchdog_task, 1);
3771 /* disable interrupts, without the synchronize_irq bit */
3773 E1000_WRITE_FLUSH();
3775 if (likely(napi_schedule_prep(&adapter->napi))) {
3776 adapter->total_tx_bytes = 0;
3777 adapter->total_tx_packets = 0;
3778 adapter->total_rx_bytes = 0;
3779 adapter->total_rx_packets = 0;
3780 __napi_schedule(&adapter->napi);
3782 /* this really should not happen! if it does it is basically a
3783 * bug, but not a hard error, so enable ints and continue
3785 if (!test_bit(__E1000_DOWN, &adapter->flags))
3786 e1000_irq_enable(adapter);
3793 * e1000_clean - NAPI Rx polling callback
3794 * @adapter: board private structure
3796 static int e1000_clean(struct napi_struct *napi, int budget)
3798 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter,
3800 int tx_clean_complete = 0, work_done = 0;
3802 tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]);
3804 adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget);
3806 if (!tx_clean_complete || work_done == budget)
3809 /* Exit the polling mode, but don't re-enable interrupts if stack might
3810 * poll us due to busy-polling
3812 if (likely(napi_complete_done(napi, work_done))) {
3813 if (likely(adapter->itr_setting & 3))
3814 e1000_set_itr(adapter);
3815 if (!test_bit(__E1000_DOWN, &adapter->flags))
3816 e1000_irq_enable(adapter);
3823 * e1000_clean_tx_irq - Reclaim resources after transmit completes
3824 * @adapter: board private structure
3826 static bool e1000_clean_tx_irq(struct e1000_adapter *adapter,
3827 struct e1000_tx_ring *tx_ring)
3829 struct e1000_hw *hw = &adapter->hw;
3830 struct net_device *netdev = adapter->netdev;
3831 struct e1000_tx_desc *tx_desc, *eop_desc;
3832 struct e1000_tx_buffer *buffer_info;
3833 unsigned int i, eop;
3834 unsigned int count = 0;
3835 unsigned int total_tx_bytes = 0, total_tx_packets = 0;
3836 unsigned int bytes_compl = 0, pkts_compl = 0;
3838 i = tx_ring->next_to_clean;
3839 eop = tx_ring->buffer_info[i].next_to_watch;
3840 eop_desc = E1000_TX_DESC(*tx_ring, eop);
3842 while ((eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) &&
3843 (count < tx_ring->count)) {
3844 bool cleaned = false;
3845 dma_rmb(); /* read buffer_info after eop_desc */
3846 for ( ; !cleaned; count++) {
3847 tx_desc = E1000_TX_DESC(*tx_ring, i);
3848 buffer_info = &tx_ring->buffer_info[i];
3849 cleaned = (i == eop);
3852 total_tx_packets += buffer_info->segs;
3853 total_tx_bytes += buffer_info->bytecount;
3854 if (buffer_info->skb) {
3855 bytes_compl += buffer_info->skb->len;
3860 e1000_unmap_and_free_tx_resource(adapter, buffer_info);
3861 tx_desc->upper.data = 0;
3863 if (unlikely(++i == tx_ring->count))
3867 eop = tx_ring->buffer_info[i].next_to_watch;
3868 eop_desc = E1000_TX_DESC(*tx_ring, eop);
3871 /* Synchronize with E1000_DESC_UNUSED called from e1000_xmit_frame,
3872 * which will reuse the cleaned buffers.
3874 smp_store_release(&tx_ring->next_to_clean, i);
3876 netdev_completed_queue(netdev, pkts_compl, bytes_compl);
3878 #define TX_WAKE_THRESHOLD 32
3879 if (unlikely(count && netif_carrier_ok(netdev) &&
3880 E1000_DESC_UNUSED(tx_ring) >= TX_WAKE_THRESHOLD)) {
3881 /* Make sure that anybody stopping the queue after this
3882 * sees the new next_to_clean.
3886 if (netif_queue_stopped(netdev) &&
3887 !(test_bit(__E1000_DOWN, &adapter->flags))) {
3888 netif_wake_queue(netdev);
3889 ++adapter->restart_queue;
3893 if (adapter->detect_tx_hung) {
3894 /* Detect a transmit hang in hardware, this serializes the
3895 * check with the clearing of time_stamp and movement of i
3897 adapter->detect_tx_hung = false;
3898 if (tx_ring->buffer_info[eop].time_stamp &&
3899 time_after(jiffies, tx_ring->buffer_info[eop].time_stamp +
3900 (adapter->tx_timeout_factor * HZ)) &&
3901 !(er32(STATUS) & E1000_STATUS_TXOFF)) {
3903 /* detected Tx unit hang */
3904 e_err(drv, "Detected Tx Unit Hang\n"
3908 " next_to_use <%x>\n"
3909 " next_to_clean <%x>\n"
3910 "buffer_info[next_to_clean]\n"
3911 " time_stamp <%lx>\n"
3912 " next_to_watch <%x>\n"
3914 " next_to_watch.status <%x>\n",
3915 (unsigned long)(tx_ring - adapter->tx_ring),
3916 readl(hw->hw_addr + tx_ring->tdh),
3917 readl(hw->hw_addr + tx_ring->tdt),
3918 tx_ring->next_to_use,
3919 tx_ring->next_to_clean,
3920 tx_ring->buffer_info[eop].time_stamp,
3923 eop_desc->upper.fields.status);
3924 e1000_dump(adapter);
3925 netif_stop_queue(netdev);
3928 adapter->total_tx_bytes += total_tx_bytes;
3929 adapter->total_tx_packets += total_tx_packets;
3930 netdev->stats.tx_bytes += total_tx_bytes;
3931 netdev->stats.tx_packets += total_tx_packets;
3932 return count < tx_ring->count;
3936 * e1000_rx_checksum - Receive Checksum Offload for 82543
3937 * @adapter: board private structure
3938 * @status_err: receive descriptor status and error fields
3939 * @csum: receive descriptor csum field
3940 * @sk_buff: socket buffer with received data
3942 static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
3943 u32 csum, struct sk_buff *skb)
3945 struct e1000_hw *hw = &adapter->hw;
3946 u16 status = (u16)status_err;
3947 u8 errors = (u8)(status_err >> 24);
3949 skb_checksum_none_assert(skb);
3951 /* 82543 or newer only */
3952 if (unlikely(hw->mac_type < e1000_82543))
3954 /* Ignore Checksum bit is set */
3955 if (unlikely(status & E1000_RXD_STAT_IXSM))
3957 /* TCP/UDP checksum error bit is set */
3958 if (unlikely(errors & E1000_RXD_ERR_TCPE)) {
3959 /* let the stack verify checksum errors */
3960 adapter->hw_csum_err++;
3963 /* TCP/UDP Checksum has not been calculated */
3964 if (!(status & E1000_RXD_STAT_TCPCS))
3967 /* It must be a TCP or UDP packet with a valid checksum */
3968 if (likely(status & E1000_RXD_STAT_TCPCS)) {
3969 /* TCP checksum is good */
3970 skb->ip_summed = CHECKSUM_UNNECESSARY;
3972 adapter->hw_csum_good++;
3976 * e1000_consume_page - helper function for jumbo Rx path
3978 static void e1000_consume_page(struct e1000_rx_buffer *bi, struct sk_buff *skb,
3981 bi->rxbuf.page = NULL;
3983 skb->data_len += length;
3984 skb->truesize += PAGE_SIZE;
3988 * e1000_receive_skb - helper function to handle rx indications
3989 * @adapter: board private structure
3990 * @status: descriptor status field as written by hardware
3991 * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
3992 * @skb: pointer to sk_buff to be indicated to stack
3994 static void e1000_receive_skb(struct e1000_adapter *adapter, u8 status,
3995 __le16 vlan, struct sk_buff *skb)
3997 skb->protocol = eth_type_trans(skb, adapter->netdev);
3999 if (status & E1000_RXD_STAT_VP) {
4000 u16 vid = le16_to_cpu(vlan) & E1000_RXD_SPC_VLAN_MASK;
4002 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vid);
4004 napi_gro_receive(&adapter->napi, skb);
4008 * e1000_tbi_adjust_stats
4009 * @hw: Struct containing variables accessed by shared code
4010 * @frame_len: The length of the frame in question
4011 * @mac_addr: The Ethernet destination address of the frame in question
4013 * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT
4015 static void e1000_tbi_adjust_stats(struct e1000_hw *hw,
4016 struct e1000_hw_stats *stats,
4017 u32 frame_len, const u8 *mac_addr)
4021 /* First adjust the frame length. */
4023 /* We need to adjust the statistics counters, since the hardware
4024 * counters overcount this packet as a CRC error and undercount
4025 * the packet as a good packet
4027 /* This packet should not be counted as a CRC error. */
4029 /* This packet does count as a Good Packet Received. */
4032 /* Adjust the Good Octets received counters */
4033 carry_bit = 0x80000000 & stats->gorcl;
4034 stats->gorcl += frame_len;
4035 /* If the high bit of Gorcl (the low 32 bits of the Good Octets
4036 * Received Count) was one before the addition,
4037 * AND it is zero after, then we lost the carry out,
4038 * need to add one to Gorch (Good Octets Received Count High).
4039 * This could be simplified if all environments supported
4042 if (carry_bit && ((stats->gorcl & 0x80000000) == 0))
4044 /* Is this a broadcast or multicast? Check broadcast first,
4045 * since the test for a multicast frame will test positive on
4046 * a broadcast frame.
4048 if (is_broadcast_ether_addr(mac_addr))
4050 else if (is_multicast_ether_addr(mac_addr))
4053 if (frame_len == hw->max_frame_size) {
4054 /* In this case, the hardware has overcounted the number of
4061 /* Adjust the bin counters when the extra byte put the frame in the
4062 * wrong bin. Remember that the frame_len was adjusted above.
4064 if (frame_len == 64) {
4067 } else if (frame_len == 127) {
4070 } else if (frame_len == 255) {
4073 } else if (frame_len == 511) {
4076 } else if (frame_len == 1023) {
4079 } else if (frame_len == 1522) {
4084 static bool e1000_tbi_should_accept(struct e1000_adapter *adapter,
4085 u8 status, u8 errors,
4086 u32 length, const u8 *data)
4088 struct e1000_hw *hw = &adapter->hw;
4089 u8 last_byte = *(data + length - 1);
4091 if (TBI_ACCEPT(hw, status, errors, length, last_byte)) {
4092 unsigned long irq_flags;
4094 spin_lock_irqsave(&adapter->stats_lock, irq_flags);
4095 e1000_tbi_adjust_stats(hw, &adapter->stats, length, data);
4096 spin_unlock_irqrestore(&adapter->stats_lock, irq_flags);
4104 static struct sk_buff *e1000_alloc_rx_skb(struct e1000_adapter *adapter,
4107 struct sk_buff *skb = napi_alloc_skb(&adapter->napi, bufsz);
4110 adapter->alloc_rx_buff_failed++;
4115 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
4116 * @adapter: board private structure
4117 * @rx_ring: ring to clean
4118 * @work_done: amount of napi work completed this call
4119 * @work_to_do: max amount of work allowed for this call to do
4121 * the return value indicates whether actual cleaning was done, there
4122 * is no guarantee that everything was cleaned
4124 static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
4125 struct e1000_rx_ring *rx_ring,
4126 int *work_done, int work_to_do)
4128 struct net_device *netdev = adapter->netdev;
4129 struct pci_dev *pdev = adapter->pdev;
4130 struct e1000_rx_desc *rx_desc, *next_rxd;
4131 struct e1000_rx_buffer *buffer_info, *next_buffer;
4134 int cleaned_count = 0;
4135 bool cleaned = false;
4136 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
4138 i = rx_ring->next_to_clean;
4139 rx_desc = E1000_RX_DESC(*rx_ring, i);
4140 buffer_info = &rx_ring->buffer_info[i];
4142 while (rx_desc->status & E1000_RXD_STAT_DD) {
4143 struct sk_buff *skb;
4146 if (*work_done >= work_to_do)
4149 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */
4151 status = rx_desc->status;
4153 if (++i == rx_ring->count)
4156 next_rxd = E1000_RX_DESC(*rx_ring, i);
4159 next_buffer = &rx_ring->buffer_info[i];
4163 dma_unmap_page(&pdev->dev, buffer_info->dma,
4164 adapter->rx_buffer_len, DMA_FROM_DEVICE);
4165 buffer_info->dma = 0;
4167 length = le16_to_cpu(rx_desc->length);
4169 /* errors is only valid for DD + EOP descriptors */
4170 if (unlikely((status & E1000_RXD_STAT_EOP) &&
4171 (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
4172 u8 *mapped = page_address(buffer_info->rxbuf.page);
4174 if (e1000_tbi_should_accept(adapter, status,
4178 } else if (netdev->features & NETIF_F_RXALL) {
4181 /* an error means any chain goes out the window
4184 if (rx_ring->rx_skb_top)
4185 dev_kfree_skb(rx_ring->rx_skb_top);
4186 rx_ring->rx_skb_top = NULL;
4191 #define rxtop rx_ring->rx_skb_top
4193 if (!(status & E1000_RXD_STAT_EOP)) {
4194 /* this descriptor is only the beginning (or middle) */
4196 /* this is the beginning of a chain */
4197 rxtop = napi_get_frags(&adapter->napi);
4201 skb_fill_page_desc(rxtop, 0,
4202 buffer_info->rxbuf.page,
4205 /* this is the middle of a chain */
4206 skb_fill_page_desc(rxtop,
4207 skb_shinfo(rxtop)->nr_frags,
4208 buffer_info->rxbuf.page, 0, length);
4210 e1000_consume_page(buffer_info, rxtop, length);
4214 /* end of the chain */
4215 skb_fill_page_desc(rxtop,
4216 skb_shinfo(rxtop)->nr_frags,
4217 buffer_info->rxbuf.page, 0, length);
4220 e1000_consume_page(buffer_info, skb, length);
4223 /* no chain, got EOP, this buf is the packet
4224 * copybreak to save the put_page/alloc_page
4226 p = buffer_info->rxbuf.page;
4227 if (length <= copybreak) {
4230 if (likely(!(netdev->features & NETIF_F_RXFCS)))
4232 skb = e1000_alloc_rx_skb(adapter,
4237 vaddr = kmap_atomic(p);
4238 memcpy(skb_tail_pointer(skb), vaddr,
4240 kunmap_atomic(vaddr);
4241 /* re-use the page, so don't erase
4242 * buffer_info->rxbuf.page
4244 skb_put(skb, length);
4245 e1000_rx_checksum(adapter,
4246 status | rx_desc->errors << 24,
4247 le16_to_cpu(rx_desc->csum), skb);
4249 total_rx_bytes += skb->len;
4252 e1000_receive_skb(adapter, status,
4253 rx_desc->special, skb);
4256 skb = napi_get_frags(&adapter->napi);
4258 adapter->alloc_rx_buff_failed++;
4261 skb_fill_page_desc(skb, 0, p, 0,
4263 e1000_consume_page(buffer_info, skb,
4269 /* Receive Checksum Offload XXX recompute due to CRC strip? */
4270 e1000_rx_checksum(adapter,
4272 ((u32)(rx_desc->errors) << 24),
4273 le16_to_cpu(rx_desc->csum), skb);
4275 total_rx_bytes += (skb->len - 4); /* don't count FCS */
4276 if (likely(!(netdev->features & NETIF_F_RXFCS)))
4277 pskb_trim(skb, skb->len - 4);
4280 if (status & E1000_RXD_STAT_VP) {
4281 __le16 vlan = rx_desc->special;
4282 u16 vid = le16_to_cpu(vlan) & E1000_RXD_SPC_VLAN_MASK;
4284 __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vid);
4287 napi_gro_frags(&adapter->napi);
4290 rx_desc->status = 0;
4292 /* return some buffers to hardware, one at a time is too slow */
4293 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
4294 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4298 /* use prefetched values */
4300 buffer_info = next_buffer;
4302 rx_ring->next_to_clean = i;
4304 cleaned_count = E1000_DESC_UNUSED(rx_ring);
4306 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4308 adapter->total_rx_packets += total_rx_packets;
4309 adapter->total_rx_bytes += total_rx_bytes;
4310 netdev->stats.rx_bytes += total_rx_bytes;
4311 netdev->stats.rx_packets += total_rx_packets;
4315 /* this should improve performance for small packets with large amounts
4316 * of reassembly being done in the stack
4318 static struct sk_buff *e1000_copybreak(struct e1000_adapter *adapter,
4319 struct e1000_rx_buffer *buffer_info,
4320 u32 length, const void *data)
4322 struct sk_buff *skb;
4324 if (length > copybreak)
4327 skb = e1000_alloc_rx_skb(adapter, length);
4331 dma_sync_single_for_cpu(&adapter->pdev->dev, buffer_info->dma,
4332 length, DMA_FROM_DEVICE);
4334 skb_put_data(skb, data, length);
4340 * e1000_clean_rx_irq - Send received data up the network stack; legacy
4341 * @adapter: board private structure
4342 * @rx_ring: ring to clean
4343 * @work_done: amount of napi work completed this call
4344 * @work_to_do: max amount of work allowed for this call to do
4346 static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
4347 struct e1000_rx_ring *rx_ring,
4348 int *work_done, int work_to_do)
4350 struct net_device *netdev = adapter->netdev;
4351 struct pci_dev *pdev = adapter->pdev;
4352 struct e1000_rx_desc *rx_desc, *next_rxd;
4353 struct e1000_rx_buffer *buffer_info, *next_buffer;
4356 int cleaned_count = 0;
4357 bool cleaned = false;
4358 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
4360 i = rx_ring->next_to_clean;
4361 rx_desc = E1000_RX_DESC(*rx_ring, i);
4362 buffer_info = &rx_ring->buffer_info[i];
4364 while (rx_desc->status & E1000_RXD_STAT_DD) {
4365 struct sk_buff *skb;
4369 if (*work_done >= work_to_do)
4372 dma_rmb(); /* read descriptor and rx_buffer_info after status DD */
4374 status = rx_desc->status;
4375 length = le16_to_cpu(rx_desc->length);
4377 data = buffer_info->rxbuf.data;
4379 skb = e1000_copybreak(adapter, buffer_info, length, data);
4381 unsigned int frag_len = e1000_frag_len(adapter);
4383 skb = build_skb(data - E1000_HEADROOM, frag_len);
4385 adapter->alloc_rx_buff_failed++;
4389 skb_reserve(skb, E1000_HEADROOM);
4390 dma_unmap_single(&pdev->dev, buffer_info->dma,
4391 adapter->rx_buffer_len,
4393 buffer_info->dma = 0;
4394 buffer_info->rxbuf.data = NULL;
4397 if (++i == rx_ring->count)
4400 next_rxd = E1000_RX_DESC(*rx_ring, i);
4403 next_buffer = &rx_ring->buffer_info[i];
4408 /* !EOP means multiple descriptors were used to store a single
4409 * packet, if thats the case we need to toss it. In fact, we
4410 * to toss every packet with the EOP bit clear and the next
4411 * frame that _does_ have the EOP bit set, as it is by
4412 * definition only a frame fragment
4414 if (unlikely(!(status & E1000_RXD_STAT_EOP)))
4415 adapter->discarding = true;
4417 if (adapter->discarding) {
4418 /* All receives must fit into a single buffer */
4419 netdev_dbg(netdev, "Receive packet consumed multiple buffers\n");
4421 if (status & E1000_RXD_STAT_EOP)
4422 adapter->discarding = false;
4426 if (unlikely(rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK)) {
4427 if (e1000_tbi_should_accept(adapter, status,
4431 } else if (netdev->features & NETIF_F_RXALL) {
4440 total_rx_bytes += (length - 4); /* don't count FCS */
4443 if (likely(!(netdev->features & NETIF_F_RXFCS)))
4444 /* adjust length to remove Ethernet CRC, this must be
4445 * done after the TBI_ACCEPT workaround above
4449 if (buffer_info->rxbuf.data == NULL)
4450 skb_put(skb, length);
4451 else /* copybreak skb */
4452 skb_trim(skb, length);
4454 /* Receive Checksum Offload */
4455 e1000_rx_checksum(adapter,
4457 ((u32)(rx_desc->errors) << 24),
4458 le16_to_cpu(rx_desc->csum), skb);
4460 e1000_receive_skb(adapter, status, rx_desc->special, skb);
4463 rx_desc->status = 0;
4465 /* return some buffers to hardware, one at a time is too slow */
4466 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
4467 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4471 /* use prefetched values */
4473 buffer_info = next_buffer;
4475 rx_ring->next_to_clean = i;
4477 cleaned_count = E1000_DESC_UNUSED(rx_ring);
4479 adapter->alloc_rx_buf(adapter, rx_ring, cleaned_count);
4481 adapter->total_rx_packets += total_rx_packets;
4482 adapter->total_rx_bytes += total_rx_bytes;
4483 netdev->stats.rx_bytes += total_rx_bytes;
4484 netdev->stats.rx_packets += total_rx_packets;
4489 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
4490 * @adapter: address of board private structure
4491 * @rx_ring: pointer to receive ring structure
4492 * @cleaned_count: number of buffers to allocate this pass
4495 e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
4496 struct e1000_rx_ring *rx_ring, int cleaned_count)
4498 struct pci_dev *pdev = adapter->pdev;
4499 struct e1000_rx_desc *rx_desc;
4500 struct e1000_rx_buffer *buffer_info;
4503 i = rx_ring->next_to_use;
4504 buffer_info = &rx_ring->buffer_info[i];
4506 while (cleaned_count--) {
4507 /* allocate a new page if necessary */
4508 if (!buffer_info->rxbuf.page) {
4509 buffer_info->rxbuf.page = alloc_page(GFP_ATOMIC);
4510 if (unlikely(!buffer_info->rxbuf.page)) {
4511 adapter->alloc_rx_buff_failed++;
4516 if (!buffer_info->dma) {
4517 buffer_info->dma = dma_map_page(&pdev->dev,
4518 buffer_info->rxbuf.page, 0,
4519 adapter->rx_buffer_len,
4521 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
4522 put_page(buffer_info->rxbuf.page);
4523 buffer_info->rxbuf.page = NULL;
4524 buffer_info->dma = 0;
4525 adapter->alloc_rx_buff_failed++;
4530 rx_desc = E1000_RX_DESC(*rx_ring, i);
4531 rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
4533 if (unlikely(++i == rx_ring->count))
4535 buffer_info = &rx_ring->buffer_info[i];
4538 if (likely(rx_ring->next_to_use != i)) {
4539 rx_ring->next_to_use = i;
4540 if (unlikely(i-- == 0))
4541 i = (rx_ring->count - 1);
4543 /* Force memory writes to complete before letting h/w
4544 * know there are new descriptors to fetch. (Only
4545 * applicable for weak-ordered memory model archs,
4549 writel(i, adapter->hw.hw_addr + rx_ring->rdt);
4554 * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
4555 * @adapter: address of board private structure
4557 static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
4558 struct e1000_rx_ring *rx_ring,
4561 struct e1000_hw *hw = &adapter->hw;
4562 struct pci_dev *pdev = adapter->pdev;
4563 struct e1000_rx_desc *rx_desc;
4564 struct e1000_rx_buffer *buffer_info;
4566 unsigned int bufsz = adapter->rx_buffer_len;
4568 i = rx_ring->next_to_use;
4569 buffer_info = &rx_ring->buffer_info[i];
4571 while (cleaned_count--) {
4574 if (buffer_info->rxbuf.data)
4577 data = e1000_alloc_frag(adapter);
4579 /* Better luck next round */
4580 adapter->alloc_rx_buff_failed++;
4584 /* Fix for errata 23, can't cross 64kB boundary */
4585 if (!e1000_check_64k_bound(adapter, data, bufsz)) {
4586 void *olddata = data;
4587 e_err(rx_err, "skb align check failed: %u bytes at "
4588 "%p\n", bufsz, data);
4589 /* Try again, without freeing the previous */
4590 data = e1000_alloc_frag(adapter);
4591 /* Failed allocation, critical failure */
4593 skb_free_frag(olddata);
4594 adapter->alloc_rx_buff_failed++;
4598 if (!e1000_check_64k_bound(adapter, data, bufsz)) {
4600 skb_free_frag(data);
4601 skb_free_frag(olddata);
4602 adapter->alloc_rx_buff_failed++;
4606 /* Use new allocation */
4607 skb_free_frag(olddata);
4609 buffer_info->dma = dma_map_single(&pdev->dev,
4611 adapter->rx_buffer_len,
4613 if (dma_mapping_error(&pdev->dev, buffer_info->dma)) {
4614 skb_free_frag(data);
4615 buffer_info->dma = 0;
4616 adapter->alloc_rx_buff_failed++;
4620 /* XXX if it was allocated cleanly it will never map to a
4624 /* Fix for errata 23, can't cross 64kB boundary */
4625 if (!e1000_check_64k_bound(adapter,
4626 (void *)(unsigned long)buffer_info->dma,
4627 adapter->rx_buffer_len)) {
4628 e_err(rx_err, "dma align check failed: %u bytes at "
4629 "%p\n", adapter->rx_buffer_len,
4630 (void *)(unsigned long)buffer_info->dma);
4632 dma_unmap_single(&pdev->dev, buffer_info->dma,
4633 adapter->rx_buffer_len,
4636 skb_free_frag(data);
4637 buffer_info->rxbuf.data = NULL;
4638 buffer_info->dma = 0;
4640 adapter->alloc_rx_buff_failed++;
4643 buffer_info->rxbuf.data = data;
4645 rx_desc = E1000_RX_DESC(*rx_ring, i);
4646 rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
4648 if (unlikely(++i == rx_ring->count))
4650 buffer_info = &rx_ring->buffer_info[i];
4653 if (likely(rx_ring->next_to_use != i)) {
4654 rx_ring->next_to_use = i;
4655 if (unlikely(i-- == 0))
4656 i = (rx_ring->count - 1);
4658 /* Force memory writes to complete before letting h/w
4659 * know there are new descriptors to fetch. (Only
4660 * applicable for weak-ordered memory model archs,
4664 writel(i, hw->hw_addr + rx_ring->rdt);
4669 * e1000_smartspeed - Workaround for SmartSpeed on 82541 and 82547 controllers.
4672 static void e1000_smartspeed(struct e1000_adapter *adapter)
4674 struct e1000_hw *hw = &adapter->hw;
4678 if ((hw->phy_type != e1000_phy_igp) || !hw->autoneg ||
4679 !(hw->autoneg_advertised & ADVERTISE_1000_FULL))
4682 if (adapter->smartspeed == 0) {
4683 /* If Master/Slave config fault is asserted twice,
4684 * we assume back-to-back
4686 e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
4687 if (!(phy_status & SR_1000T_MS_CONFIG_FAULT))
4689 e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_status);
4690 if (!(phy_status & SR_1000T_MS_CONFIG_FAULT))
4692 e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
4693 if (phy_ctrl & CR_1000T_MS_ENABLE) {
4694 phy_ctrl &= ~CR_1000T_MS_ENABLE;
4695 e1000_write_phy_reg(hw, PHY_1000T_CTRL,
4697 adapter->smartspeed++;
4698 if (!e1000_phy_setup_autoneg(hw) &&
4699 !e1000_read_phy_reg(hw, PHY_CTRL,
4701 phy_ctrl |= (MII_CR_AUTO_NEG_EN |
4702 MII_CR_RESTART_AUTO_NEG);
4703 e1000_write_phy_reg(hw, PHY_CTRL,
4708 } else if (adapter->smartspeed == E1000_SMARTSPEED_DOWNSHIFT) {
4709 /* If still no link, perhaps using 2/3 pair cable */
4710 e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_ctrl);
4711 phy_ctrl |= CR_1000T_MS_ENABLE;
4712 e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_ctrl);
4713 if (!e1000_phy_setup_autoneg(hw) &&
4714 !e1000_read_phy_reg(hw, PHY_CTRL, &phy_ctrl)) {
4715 phy_ctrl |= (MII_CR_AUTO_NEG_EN |
4716 MII_CR_RESTART_AUTO_NEG);
4717 e1000_write_phy_reg(hw, PHY_CTRL, phy_ctrl);
4720 /* Restart process after E1000_SMARTSPEED_MAX iterations */
4721 if (adapter->smartspeed++ == E1000_SMARTSPEED_MAX)
4722 adapter->smartspeed = 0;
4731 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
4737 return e1000_mii_ioctl(netdev, ifr, cmd);
4749 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
4752 struct e1000_adapter *adapter = netdev_priv(netdev);
4753 struct e1000_hw *hw = &adapter->hw;
4754 struct mii_ioctl_data *data = if_mii(ifr);
4757 unsigned long flags;
4759 if (hw->media_type != e1000_media_type_copper)
4764 data->phy_id = hw->phy_addr;
4767 spin_lock_irqsave(&adapter->stats_lock, flags);
4768 if (e1000_read_phy_reg(hw, data->reg_num & 0x1F,
4770 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4773 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4776 if (data->reg_num & ~(0x1F))
4778 mii_reg = data->val_in;
4779 spin_lock_irqsave(&adapter->stats_lock, flags);
4780 if (e1000_write_phy_reg(hw, data->reg_num,
4782 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4785 spin_unlock_irqrestore(&adapter->stats_lock, flags);
4786 if (hw->media_type == e1000_media_type_copper) {
4787 switch (data->reg_num) {
4789 if (mii_reg & MII_CR_POWER_DOWN)
4791 if (mii_reg & MII_CR_AUTO_NEG_EN) {
4793 hw->autoneg_advertised = 0x2F;
4798 else if (mii_reg & 0x2000)
4802 retval = e1000_set_spd_dplx(
4810 if (netif_running(adapter->netdev))
4811 e1000_reinit_locked(adapter);
4813 e1000_reset(adapter);
4815 case M88E1000_PHY_SPEC_CTRL:
4816 case M88E1000_EXT_PHY_SPEC_CTRL:
4817 if (e1000_phy_reset(hw))
4822 switch (data->reg_num) {
4824 if (mii_reg & MII_CR_POWER_DOWN)
4826 if (netif_running(adapter->netdev))
4827 e1000_reinit_locked(adapter);
4829 e1000_reset(adapter);
4837 return E1000_SUCCESS;
4840 void e1000_pci_set_mwi(struct e1000_hw *hw)
4842 struct e1000_adapter *adapter = hw->back;
4843 int ret_val = pci_set_mwi(adapter->pdev);
4846 e_err(probe, "Error in setting MWI\n");
4849 void e1000_pci_clear_mwi(struct e1000_hw *hw)
4851 struct e1000_adapter *adapter = hw->back;
4853 pci_clear_mwi(adapter->pdev);
4856 int e1000_pcix_get_mmrbc(struct e1000_hw *hw)
4858 struct e1000_adapter *adapter = hw->back;
4859 return pcix_get_mmrbc(adapter->pdev);
4862 void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc)
4864 struct e1000_adapter *adapter = hw->back;
4865 pcix_set_mmrbc(adapter->pdev, mmrbc);
4868 void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value)
4873 static bool e1000_vlan_used(struct e1000_adapter *adapter)
4877 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID)
4882 static void __e1000_vlan_mode(struct e1000_adapter *adapter,
4883 netdev_features_t features)
4885 struct e1000_hw *hw = &adapter->hw;
4889 if (features & NETIF_F_HW_VLAN_CTAG_RX) {
4890 /* enable VLAN tag insert/strip */
4891 ctrl |= E1000_CTRL_VME;
4893 /* disable VLAN tag insert/strip */
4894 ctrl &= ~E1000_CTRL_VME;
4898 static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter,
4901 struct e1000_hw *hw = &adapter->hw;
4904 if (!test_bit(__E1000_DOWN, &adapter->flags))
4905 e1000_irq_disable(adapter);
4907 __e1000_vlan_mode(adapter, adapter->netdev->features);
4909 /* enable VLAN receive filtering */
4911 rctl &= ~E1000_RCTL_CFIEN;
4912 if (!(adapter->netdev->flags & IFF_PROMISC))
4913 rctl |= E1000_RCTL_VFE;
4915 e1000_update_mng_vlan(adapter);
4917 /* disable VLAN receive filtering */
4919 rctl &= ~E1000_RCTL_VFE;
4923 if (!test_bit(__E1000_DOWN, &adapter->flags))
4924 e1000_irq_enable(adapter);
4927 static void e1000_vlan_mode(struct net_device *netdev,
4928 netdev_features_t features)
4930 struct e1000_adapter *adapter = netdev_priv(netdev);
4932 if (!test_bit(__E1000_DOWN, &adapter->flags))
4933 e1000_irq_disable(adapter);
4935 __e1000_vlan_mode(adapter, features);
4937 if (!test_bit(__E1000_DOWN, &adapter->flags))
4938 e1000_irq_enable(adapter);
4941 static int e1000_vlan_rx_add_vid(struct net_device *netdev,
4942 __be16 proto, u16 vid)
4944 struct e1000_adapter *adapter = netdev_priv(netdev);
4945 struct e1000_hw *hw = &adapter->hw;
4948 if ((hw->mng_cookie.status &
4949 E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) &&
4950 (vid == adapter->mng_vlan_id))
4953 if (!e1000_vlan_used(adapter))
4954 e1000_vlan_filter_on_off(adapter, true);
4956 /* add VID to filter table */
4957 index = (vid >> 5) & 0x7F;
4958 vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
4959 vfta |= (1 << (vid & 0x1F));
4960 e1000_write_vfta(hw, index, vfta);
4962 set_bit(vid, adapter->active_vlans);
4967 static int e1000_vlan_rx_kill_vid(struct net_device *netdev,
4968 __be16 proto, u16 vid)
4970 struct e1000_adapter *adapter = netdev_priv(netdev);
4971 struct e1000_hw *hw = &adapter->hw;
4974 if (!test_bit(__E1000_DOWN, &adapter->flags))
4975 e1000_irq_disable(adapter);
4976 if (!test_bit(__E1000_DOWN, &adapter->flags))
4977 e1000_irq_enable(adapter);
4979 /* remove VID from filter table */
4980 index = (vid >> 5) & 0x7F;
4981 vfta = E1000_READ_REG_ARRAY(hw, VFTA, index);
4982 vfta &= ~(1 << (vid & 0x1F));
4983 e1000_write_vfta(hw, index, vfta);
4985 clear_bit(vid, adapter->active_vlans);
4987 if (!e1000_vlan_used(adapter))
4988 e1000_vlan_filter_on_off(adapter, false);
4993 static void e1000_restore_vlan(struct e1000_adapter *adapter)
4997 if (!e1000_vlan_used(adapter))
5000 e1000_vlan_filter_on_off(adapter, true);
5001 for_each_set_bit(vid, adapter->active_vlans, VLAN_N_VID)
5002 e1000_vlan_rx_add_vid(adapter->netdev, htons(ETH_P_8021Q), vid);
5005 int e1000_set_spd_dplx(struct e1000_adapter *adapter, u32 spd, u8 dplx)
5007 struct e1000_hw *hw = &adapter->hw;
5011 /* Make sure dplx is at most 1 bit and lsb of speed is not set
5012 * for the switch() below to work
5014 if ((spd & 1) || (dplx & ~1))
5017 /* Fiber NICs only allow 1000 gbps Full duplex */
5018 if ((hw->media_type == e1000_media_type_fiber) &&
5019 spd != SPEED_1000 &&
5020 dplx != DUPLEX_FULL)
5023 switch (spd + dplx) {
5024 case SPEED_10 + DUPLEX_HALF:
5025 hw->forced_speed_duplex = e1000_10_half;
5027 case SPEED_10 + DUPLEX_FULL:
5028 hw->forced_speed_duplex = e1000_10_full;
5030 case SPEED_100 + DUPLEX_HALF:
5031 hw->forced_speed_duplex = e1000_100_half;
5033 case SPEED_100 + DUPLEX_FULL:
5034 hw->forced_speed_duplex = e1000_100_full;
5036 case SPEED_1000 + DUPLEX_FULL:
5038 hw->autoneg_advertised = ADVERTISE_1000_FULL;
5040 case SPEED_1000 + DUPLEX_HALF: /* not supported */
5045 /* clear MDI, MDI(-X) override is only allowed when autoneg enabled */
5046 hw->mdix = AUTO_ALL_MODES;
5051 e_err(probe, "Unsupported Speed/Duplex configuration\n");
5055 static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake)
5057 struct net_device *netdev = pci_get_drvdata(pdev);
5058 struct e1000_adapter *adapter = netdev_priv(netdev);
5059 struct e1000_hw *hw = &adapter->hw;
5060 u32 ctrl, ctrl_ext, rctl, status;
5061 u32 wufc = adapter->wol;
5066 netif_device_detach(netdev);
5068 if (netif_running(netdev)) {
5069 int count = E1000_CHECK_RESET_COUNT;
5071 while (test_bit(__E1000_RESETTING, &adapter->flags) && count--)
5072 usleep_range(10000, 20000);
5074 WARN_ON(test_bit(__E1000_RESETTING, &adapter->flags));
5075 e1000_down(adapter);
5079 retval = pci_save_state(pdev);
5084 status = er32(STATUS);
5085 if (status & E1000_STATUS_LU)
5086 wufc &= ~E1000_WUFC_LNKC;
5089 e1000_setup_rctl(adapter);
5090 e1000_set_rx_mode(netdev);
5094 /* turn on all-multi mode if wake on multicast is enabled */
5095 if (wufc & E1000_WUFC_MC)
5096 rctl |= E1000_RCTL_MPE;
5098 /* enable receives in the hardware */
5099 ew32(RCTL, rctl | E1000_RCTL_EN);
5101 if (hw->mac_type >= e1000_82540) {
5103 /* advertise wake from D3Cold */
5104 #define E1000_CTRL_ADVD3WUC 0x00100000
5105 /* phy power management enable */
5106 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
5107 ctrl |= E1000_CTRL_ADVD3WUC |
5108 E1000_CTRL_EN_PHY_PWR_MGMT;
5112 if (hw->media_type == e1000_media_type_fiber ||
5113 hw->media_type == e1000_media_type_internal_serdes) {
5114 /* keep the laser running in D3 */
5115 ctrl_ext = er32(CTRL_EXT);
5116 ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
5117 ew32(CTRL_EXT, ctrl_ext);
5120 ew32(WUC, E1000_WUC_PME_EN);
5127 e1000_release_manageability(adapter);
5129 *enable_wake = !!wufc;
5131 /* make sure adapter isn't asleep if manageability is enabled */
5132 if (adapter->en_mng_pt)
5133 *enable_wake = true;
5135 if (netif_running(netdev))
5136 e1000_free_irq(adapter);
5138 if (!test_and_set_bit(__E1000_DISABLED, &adapter->flags))
5139 pci_disable_device(pdev);
5145 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
5150 retval = __e1000_shutdown(pdev, &wake);
5155 pci_prepare_to_sleep(pdev);
5157 pci_wake_from_d3(pdev, false);
5158 pci_set_power_state(pdev, PCI_D3hot);
5164 static int e1000_resume(struct pci_dev *pdev)
5166 struct net_device *netdev = pci_get_drvdata(pdev);
5167 struct e1000_adapter *adapter = netdev_priv(netdev);
5168 struct e1000_hw *hw = &adapter->hw;
5171 pci_set_power_state(pdev, PCI_D0);
5172 pci_restore_state(pdev);
5173 pci_save_state(pdev);
5175 if (adapter->need_ioport)
5176 err = pci_enable_device(pdev);
5178 err = pci_enable_device_mem(pdev);
5180 pr_err("Cannot enable PCI device from suspend\n");
5184 /* flush memory to make sure state is correct */
5185 smp_mb__before_atomic();
5186 clear_bit(__E1000_DISABLED, &adapter->flags);
5187 pci_set_master(pdev);
5189 pci_enable_wake(pdev, PCI_D3hot, 0);
5190 pci_enable_wake(pdev, PCI_D3cold, 0);
5192 if (netif_running(netdev)) {
5193 err = e1000_request_irq(adapter);
5198 e1000_power_up_phy(adapter);
5199 e1000_reset(adapter);
5202 e1000_init_manageability(adapter);
5204 if (netif_running(netdev))
5207 netif_device_attach(netdev);
5213 static void e1000_shutdown(struct pci_dev *pdev)
5217 __e1000_shutdown(pdev, &wake);
5219 if (system_state == SYSTEM_POWER_OFF) {
5220 pci_wake_from_d3(pdev, wake);
5221 pci_set_power_state(pdev, PCI_D3hot);
5225 #ifdef CONFIG_NET_POLL_CONTROLLER
5226 /* Polling 'interrupt' - used by things like netconsole to send skbs
5227 * without having to re-enable interrupts. It's not called while
5228 * the interrupt routine is executing.
5230 static void e1000_netpoll(struct net_device *netdev)
5232 struct e1000_adapter *adapter = netdev_priv(netdev);
5234 if (disable_hardirq(adapter->pdev->irq))
5235 e1000_intr(adapter->pdev->irq, netdev);
5236 enable_irq(adapter->pdev->irq);
5241 * e1000_io_error_detected - called when PCI error is detected
5242 * @pdev: Pointer to PCI device
5243 * @state: The current pci connection state
5245 * This function is called after a PCI bus error affecting
5246 * this device has been detected.
5248 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
5249 pci_channel_state_t state)
5251 struct net_device *netdev = pci_get_drvdata(pdev);
5252 struct e1000_adapter *adapter = netdev_priv(netdev);
5254 netif_device_detach(netdev);
5256 if (state == pci_channel_io_perm_failure)
5257 return PCI_ERS_RESULT_DISCONNECT;
5259 if (netif_running(netdev))
5260 e1000_down(adapter);
5262 if (!test_and_set_bit(__E1000_DISABLED, &adapter->flags))
5263 pci_disable_device(pdev);
5265 /* Request a slot slot reset. */
5266 return PCI_ERS_RESULT_NEED_RESET;
5270 * e1000_io_slot_reset - called after the pci bus has been reset.
5271 * @pdev: Pointer to PCI device
5273 * Restart the card from scratch, as if from a cold-boot. Implementation
5274 * resembles the first-half of the e1000_resume routine.
5276 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
5278 struct net_device *netdev = pci_get_drvdata(pdev);
5279 struct e1000_adapter *adapter = netdev_priv(netdev);
5280 struct e1000_hw *hw = &adapter->hw;
5283 if (adapter->need_ioport)
5284 err = pci_enable_device(pdev);
5286 err = pci_enable_device_mem(pdev);
5288 pr_err("Cannot re-enable PCI device after reset.\n");
5289 return PCI_ERS_RESULT_DISCONNECT;
5292 /* flush memory to make sure state is correct */
5293 smp_mb__before_atomic();
5294 clear_bit(__E1000_DISABLED, &adapter->flags);
5295 pci_set_master(pdev);
5297 pci_enable_wake(pdev, PCI_D3hot, 0);
5298 pci_enable_wake(pdev, PCI_D3cold, 0);
5300 e1000_reset(adapter);
5303 return PCI_ERS_RESULT_RECOVERED;
5307 * e1000_io_resume - called when traffic can start flowing again.
5308 * @pdev: Pointer to PCI device
5310 * This callback is called when the error recovery driver tells us that
5311 * its OK to resume normal operation. Implementation resembles the
5312 * second-half of the e1000_resume routine.
5314 static void e1000_io_resume(struct pci_dev *pdev)
5316 struct net_device *netdev = pci_get_drvdata(pdev);
5317 struct e1000_adapter *adapter = netdev_priv(netdev);
5319 e1000_init_manageability(adapter);
5321 if (netif_running(netdev)) {
5322 if (e1000_up(adapter)) {
5323 pr_info("can't bring device back up after reset\n");
5328 netif_device_attach(netdev);