drivers/regulator/bd718x7-regulator.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 // Copyright (C) 2018 ROHM Semiconductors
   3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver
   4
   5 #include <linux/delay.h>
   6 #include <linux/err.h>
   7 #include <linux/gpio.h>
   8 #include <linux/interrupt.h>
   9 #include <linux/kernel.h>
  10 #include <linux/mfd/rohm-bd718x7.h>
  11 #include <linux/module.h>
  12 #include <linux/platform_device.h>
  13 #include <linux/regulator/driver.h>
  14 #include <linux/regulator/machine.h>
  15 #include <linux/regulator/of_regulator.h>
  16 #include <linux/slab.h>
  17
  18 /*
  19  * BUCK1/2/3/4
  20  * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
  21  * 00: 10.00mV/usec 10mV 1uS
  22  * 01: 5.00mV/usec      10mV 2uS
  23  * 10: 2.50mV/usec      10mV 4uS
  24  * 11: 1.25mV/usec      10mV 8uS
  25  */
  26 static int bd718xx_buck1234_set_ramp_delay(struct regulator_dev *rdev,
  27                                            int ramp_delay)
  28 {
  29         int id = rdev->desc->id;
  30         unsigned int ramp_value = BUCK_RAMPRATE_10P00MV;
  31
  32         dev_dbg(&rdev->dev, "Buck[%d] Set Ramp = %d\n", id + 1,
  33                 ramp_delay);
  34         switch (ramp_delay) {
  35         case 1 ... 1250:
  36                 ramp_value = BUCK_RAMPRATE_1P25MV;
  37                 break;
  38         case 1251 ... 2500:
  39                 ramp_value = BUCK_RAMPRATE_2P50MV;
  40                 break;
  41         case 2501 ... 5000:
  42                 ramp_value = BUCK_RAMPRATE_5P00MV;
  43                 break;
  44         case 5001 ... 10000:
  45                 ramp_value = BUCK_RAMPRATE_10P00MV;
  46                 break;
  47         default:
  48                 ramp_value = BUCK_RAMPRATE_10P00MV;
  49                 dev_err(&rdev->dev,
  50                         "%s: ramp_delay: %d not supported, setting 10000mV//us\n",
  51                         rdev->desc->name, ramp_delay);
  52         }
  53
  54         return regmap_update_bits(rdev->regmap, BD718XX_REG_BUCK1_CTRL + id,
  55                                   BUCK_RAMPRATE_MASK, ramp_value << 6);
  56 }
  57
  58 /* Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed.
  59  * Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage
  60  * is changed. Hence we return -EBUSY for these if voltage is changed
  61  * when BUCK/LDO is enabled.
  62  */
  63 static int bd718xx_set_voltage_sel_restricted(struct regulator_dev *rdev,
  64                                                     unsigned int sel)
  65 {
  66         if (regulator_is_enabled_regmap(rdev))
  67                 return -EBUSY;
  68
  69         return regulator_set_voltage_sel_regmap(rdev, sel);
  70 }
  71
  72 static int bd718xx_set_voltage_sel_pickable_restricted(
  73                 struct regulator_dev *rdev, unsigned int sel)
  74 {
  75         if (regulator_is_enabled_regmap(rdev))
  76                 return -EBUSY;
  77
  78         return regulator_set_voltage_sel_pickable_regmap(rdev, sel);
  79 }
  80
  81 static struct regulator_ops bd718xx_pickable_range_ldo_ops = {
  82         .enable = regulator_enable_regmap,
  83         .disable = regulator_disable_regmap,
  84         .is_enabled = regulator_is_enabled_regmap,
  85         .list_voltage = regulator_list_voltage_pickable_linear_range,
  86         .set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted,
  87         .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
  88 };
  89
  90 static struct regulator_ops bd718xx_pickable_range_buck_ops = {
  91         .enable = regulator_enable_regmap,
  92         .disable = regulator_disable_regmap,
  93         .is_enabled = regulator_is_enabled_regmap,
  94         .list_voltage = regulator_list_voltage_pickable_linear_range,
  95         .set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted,
  96         .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap,
  97         .set_voltage_time_sel = regulator_set_voltage_time_sel,
  98 };
  99
 100 static struct regulator_ops bd718xx_ldo_regulator_ops = {
 101         .enable = regulator_enable_regmap,
 102         .disable = regulator_disable_regmap,
 103         .is_enabled = regulator_is_enabled_regmap,
 104         .list_voltage = regulator_list_voltage_linear_range,
 105         .set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 106         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 107 };
 108
 109 static struct regulator_ops bd718xx_ldo_regulator_nolinear_ops = {
 110         .enable = regulator_enable_regmap,
 111         .disable = regulator_disable_regmap,
 112         .is_enabled = regulator_is_enabled_regmap,
 113         .list_voltage = regulator_list_voltage_table,
 114         .set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 115         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 116 };
 117
 118 static struct regulator_ops bd718xx_buck_regulator_ops = {
 119         .enable = regulator_enable_regmap,
 120         .disable = regulator_disable_regmap,
 121         .is_enabled = regulator_is_enabled_regmap,
 122         .list_voltage = regulator_list_voltage_linear_range,
 123         .set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 124         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 125         .set_voltage_time_sel = regulator_set_voltage_time_sel,
 126 };
 127
 128 static struct regulator_ops bd718xx_buck_regulator_nolinear_ops = {
 129         .enable = regulator_enable_regmap,
 130         .disable = regulator_disable_regmap,
 131         .is_enabled = regulator_is_enabled_regmap,
 132         .list_voltage = regulator_list_voltage_table,
 133         .set_voltage_sel = bd718xx_set_voltage_sel_restricted,
 134         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 135         .set_voltage_time_sel = regulator_set_voltage_time_sel,
 136 };
 137
 138 static struct regulator_ops bd718xx_dvs_buck_regulator_ops = {
 139         .enable = regulator_enable_regmap,
 140         .disable = regulator_disable_regmap,
 141         .is_enabled = regulator_is_enabled_regmap,
 142         .list_voltage = regulator_list_voltage_linear_range,
 143         .set_voltage_sel = regulator_set_voltage_sel_regmap,
 144         .get_voltage_sel = regulator_get_voltage_sel_regmap,
 145         .set_voltage_time_sel = regulator_set_voltage_time_sel,
 146         .set_ramp_delay = bd718xx_buck1234_set_ramp_delay,
 147 };
 148
 149 /*
 150  * BD71837 BUCK1/2/3/4
 151  * BD71847 BUCK1/2
 152  * 0.70 to 1.30V (10mV step)
 153  */
 154 static const struct regulator_linear_range bd718xx_dvs_buck_volts[] = {
 155         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
 156         REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
 157 };
 158
 159 /*
 160  * BD71837 BUCK5
 161  * 0.7V to 1.35V  (range 0)
 162  * and
 163  * 0.675 to 1.325 (range 1)
 164  */
 165 static const struct regulator_linear_range bd71837_buck5_volts[] = {
 166         /* Ranges when VOLT_SEL bit is 0 */
 167         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
 168         REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
 169         REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
 170         /* Ranges when VOLT_SEL bit is 1  */
 171         REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
 172         REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
 173         REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
 174 };
 175
 176 /*
 177  * Range selector for first 3 linear ranges is 0x0
 178  * and 0x1 for last 3 ranges.
 179  */
 180 static const unsigned int bd71837_buck5_volt_range_sel[] = {
 181         0x0, 0x0, 0x0, 0x80, 0x80, 0x80
 182 };
 183
 184 /*
 185  * BD71847 BUCK3
 186  */
 187 static const struct regulator_linear_range bd71847_buck3_volts[] = {
 188         /* Ranges when VOLT_SEL bits are 00 */
 189         REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
 190         REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
 191         REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
 192         /* Ranges when VOLT_SEL bits are 01 */
 193         REGULATOR_LINEAR_RANGE(550000, 0x0, 0x7, 50000),
 194         /* Ranges when VOLT_SEL bits are 11 */
 195         REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000),
 196         REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000),
 197         REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000),
 198 };
 199
 200 static const unsigned int bd71847_buck3_volt_range_sel[] = {
 201         0x0, 0x0, 0x0, 0x40, 0x80, 0x80, 0x80
 202 };
 203
 204 static const struct regulator_linear_range bd71847_buck4_volts[] = {
 205         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 206         REGULATOR_LINEAR_RANGE(2600000, 0x00, 0x03, 100000),
 207 };
 208
 209 static const unsigned int bd71847_buck4_volt_range_sel[] = { 0x0, 0x40 };
 210
 211 /*
 212  * BUCK6
 213  * 3.0V to 3.3V (step 100mV)
 214  */
 215 static const struct regulator_linear_range bd71837_buck6_volts[] = {
 216         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 217 };
 218
 219 /*
 220  * BD71837 BUCK7
 221  * BD71847 BUCK5
 222  * 000 = 1.605V
 223  * 001 = 1.695V
 224  * 010 = 1.755V
 225  * 011 = 1.8V (Initial)
 226  * 100 = 1.845V
 227  * 101 = 1.905V
 228  * 110 = 1.95V
 229  * 111 = 1.995V
 230  */
 231 static const unsigned int bd718xx_3rd_nodvs_buck_volts[] = {
 232         1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
 233 };
 234
 235 /*
 236  * BUCK8
 237  * 0.8V to 1.40V (step 10mV)
 238  */
 239 static const struct regulator_linear_range bd718xx_4th_nodvs_buck_volts[] = {
 240         REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
 241 };
 242
 243 /*
 244  * LDO1
 245  * 3.0 to 3.3V (100mV step)
 246  */
 247 static const struct regulator_linear_range bd718xx_ldo1_volts[] = {
 248         REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
 249         REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000),
 250 };
 251
 252 static const unsigned int bd718xx_ldo1_volt_range_sel[] = { 0x0, 0x20 };
 253
 254 /*
 255  * LDO2
 256  * 0.8 or 0.9V
 257  */
 258 static const unsigned int ldo_2_volts[] = {
 259         900000, 800000
 260 };
 261
 262 /*
 263  * LDO3
 264  * 1.8 to 3.3V (100mV step)
 265  */
 266 static const struct regulator_linear_range bd718xx_ldo3_volts[] = {
 267         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 268 };
 269
 270 /*
 271  * LDO4
 272  * 0.9 to 1.8V (100mV step)
 273  */
 274 static const struct regulator_linear_range bd718xx_ldo4_volts[] = {
 275         REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
 276 };
 277
 278 /*
 279  * LDO5 for BD71837
 280  * 1.8 to 3.3V (100mV step)
 281  */
 282 static const struct regulator_linear_range bd71837_ldo5_volts[] = {
 283         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 284 };
 285
 286 /*
 287  * LDO5 for BD71837
 288  * 1.8 to 3.3V (100mV step)
 289  */
 290 static const struct regulator_linear_range bd71847_ldo5_volts[] = {
 291         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 292         REGULATOR_LINEAR_RANGE(800000, 0x00, 0x0F, 100000),
 293 };
 294
 295 static const unsigned int bd71847_ldo5_volt_range_sel[] = { 0x0, 0x20 };
 296
 297 /*
 298  * LDO6
 299  * 0.9 to 1.8V (100mV step)
 300  */
 301 static const struct regulator_linear_range bd718xx_ldo6_volts[] = {
 302         REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
 303 };
 304
 305 /*
 306  * LDO7
 307  * 1.8 to 3.3V (100mV step)
 308  */
 309 static const struct regulator_linear_range bd71837_ldo7_volts[] = {
 310         REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
 311 };
 312
 313 struct reg_init {
 314         unsigned int reg;
 315         unsigned int mask;
 316         unsigned int val;
 317 };
 318 struct bd718xx_regulator_data {
 319         struct regulator_desc desc;
 320         const struct reg_init init;
 321         const struct reg_init *additional_inits;
 322         int additional_init_amnt;
 323 };
 324
 325 /*
 326  * There is a HW quirk in BD71837. The shutdown sequence timings for
 327  * bucks/LDOs which are controlled via register interface are changed.
 328  * At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the
 329  * beginning of shut-down sequence. As bucks 6 and 7 are parent
 330  * supplies for LDO5 and LDO6 - this causes LDO5/6 voltage
 331  * monitoring to errorneously detect under voltage and force PMIC to
 332  * emergency state instead of poweroff. In order to avoid this we
 333  * disable voltage monitoring for LDO5 and LDO6
 334  */
 335 static const struct reg_init bd71837_ldo5_inits[] = {
 336         {
 337                 .reg = BD718XX_REG_MVRFLTMASK2,
 338                 .mask = BD718XX_LDO5_VRMON80,
 339                 .val = BD718XX_LDO5_VRMON80,
 340         },
 341 };
 342
 343 static const struct reg_init bd71837_ldo6_inits[] = {
 344         {
 345                 .reg = BD718XX_REG_MVRFLTMASK2,
 346                 .mask = BD718XX_LDO6_VRMON80,
 347                 .val = BD718XX_LDO6_VRMON80,
 348         },
 349 };
 350
 351 static const struct bd718xx_regulator_data bd71847_regulators[] = {
 352         {
 353                 .desc = {
 354                         .name = "buck1",
 355                         .of_match = of_match_ptr("BUCK1"),
 356                         .regulators_node = of_match_ptr("regulators"),
 357                         .id = BD718XX_BUCK1,
 358                         .ops = &bd718xx_dvs_buck_regulator_ops,
 359                         .type = REGULATOR_VOLTAGE,
 360                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 361                         .linear_ranges = bd718xx_dvs_buck_volts,
 362                         .n_linear_ranges =
 363                                 ARRAY_SIZE(bd718xx_dvs_buck_volts),
 364                         .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
 365                         .vsel_mask = DVS_BUCK_RUN_MASK,
 366                         .enable_reg = BD718XX_REG_BUCK1_CTRL,
 367                         .enable_mask = BD718XX_BUCK_EN,
 368                         .owner = THIS_MODULE,
 369                 },
 370                 .init = {
 371                         .reg = BD718XX_REG_BUCK1_CTRL,
 372                         .mask = BD718XX_BUCK_SEL,
 373                         .val = BD718XX_BUCK_SEL,
 374                 },
 375         },
 376         {
 377                 .desc = {
 378                         .name = "buck2",
 379                         .of_match = of_match_ptr("BUCK2"),
 380                         .regulators_node = of_match_ptr("regulators"),
 381                         .id = BD718XX_BUCK2,
 382                         .ops = &bd718xx_dvs_buck_regulator_ops,
 383                         .type = REGULATOR_VOLTAGE,
 384                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 385                         .linear_ranges = bd718xx_dvs_buck_volts,
 386                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 387                         .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
 388                         .vsel_mask = DVS_BUCK_RUN_MASK,
 389                         .enable_reg = BD718XX_REG_BUCK2_CTRL,
 390                         .enable_mask = BD718XX_BUCK_EN,
 391                         .owner = THIS_MODULE,
 392                 },
 393                 .init = {
 394                         .reg = BD718XX_REG_BUCK2_CTRL,
 395                         .mask = BD718XX_BUCK_SEL,
 396                         .val = BD718XX_BUCK_SEL,
 397                 },
 398         },
 399         {
 400                 .desc = {
 401                         .name = "buck3",
 402                         .of_match = of_match_ptr("BUCK3"),
 403                         .regulators_node = of_match_ptr("regulators"),
 404                         .id = BD718XX_BUCK3,
 405                         .ops = &bd718xx_pickable_range_buck_ops,
 406                         .type = REGULATOR_VOLTAGE,
 407                         .n_voltages = BD71847_BUCK3_VOLTAGE_NUM,
 408                         .linear_ranges = bd71847_buck3_volts,
 409                         .n_linear_ranges =
 410                                 ARRAY_SIZE(bd71847_buck3_volts),
 411                         .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 412                         .vsel_mask = BD718XX_1ST_NODVS_BUCK_MASK,
 413                         .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 414                         .vsel_range_mask = BD71847_BUCK3_RANGE_MASK,
 415                         .linear_range_selectors = bd71847_buck3_volt_range_sel,
 416                         .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 417                         .enable_mask = BD718XX_BUCK_EN,
 418                         .owner = THIS_MODULE,
 419                 },
 420                 .init = {
 421                         .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 422                         .mask = BD718XX_BUCK_SEL,
 423                         .val = BD718XX_BUCK_SEL,
 424                 },
 425         },
 426         {
 427                 .desc = {
 428                         .name = "buck4",
 429                         .of_match = of_match_ptr("BUCK4"),
 430                         .regulators_node = of_match_ptr("regulators"),
 431                         .id = BD718XX_BUCK4,
 432                         .ops = &bd718xx_pickable_range_buck_ops,
 433                         .type = REGULATOR_VOLTAGE,
 434                         .n_voltages = BD71847_BUCK4_VOLTAGE_NUM,
 435                         .linear_ranges = bd71847_buck4_volts,
 436                         .n_linear_ranges =
 437                                 ARRAY_SIZE(bd71847_buck4_volts),
 438                         .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 439                         .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
 440                         .vsel_mask = BD71847_BUCK4_MASK,
 441                         .vsel_range_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
 442                         .vsel_range_mask = BD71847_BUCK4_RANGE_MASK,
 443                         .linear_range_selectors = bd71847_buck4_volt_range_sel,
 444                         .enable_mask = BD718XX_BUCK_EN,
 445                         .owner = THIS_MODULE,
 446                 },
 447                 .init = {
 448                         .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 449                         .mask = BD718XX_BUCK_SEL,
 450                         .val = BD718XX_BUCK_SEL,
 451                 },
 452         },
 453         {
 454                 .desc = {
 455                         .name = "buck5",
 456                         .of_match = of_match_ptr("BUCK5"),
 457                         .regulators_node = of_match_ptr("regulators"),
 458                         .id = BD718XX_BUCK5,
 459                         .ops = &bd718xx_buck_regulator_nolinear_ops,
 460                         .type = REGULATOR_VOLTAGE,
 461                         .volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
 462                         .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
 463                         .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
 464                         .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
 465                         .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 466                         .enable_mask = BD718XX_BUCK_EN,
 467                         .owner = THIS_MODULE,
 468                 },
 469                 .init = {
 470                         .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 471                         .mask = BD718XX_BUCK_SEL,
 472                         .val = BD718XX_BUCK_SEL,
 473                 },
 474         },
 475         {
 476                 .desc = {
 477                         .name = "buck6",
 478                         .of_match = of_match_ptr("BUCK6"),
 479                         .regulators_node = of_match_ptr("regulators"),
 480                         .id = BD718XX_BUCK6,
 481                         .ops = &bd718xx_buck_regulator_ops,
 482                         .type = REGULATOR_VOLTAGE,
 483                         .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
 484                         .linear_ranges = bd718xx_4th_nodvs_buck_volts,
 485                         .n_linear_ranges =
 486                                 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
 487                         .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
 488                         .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
 489                         .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 490                         .enable_mask = BD718XX_BUCK_EN,
 491                         .owner = THIS_MODULE,
 492                 },
 493                 .init = {
 494                         .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 495                         .mask = BD718XX_BUCK_SEL,
 496                         .val = BD718XX_BUCK_SEL,
 497                 },
 498         },
 499         {
 500                 .desc = {
 501                         .name = "ldo1",
 502                         .of_match = of_match_ptr("LDO1"),
 503                         .regulators_node = of_match_ptr("regulators"),
 504                         .id = BD718XX_LDO1,
 505                         .ops = &bd718xx_pickable_range_ldo_ops,
 506                         .type = REGULATOR_VOLTAGE,
 507                         .n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
 508                         .linear_ranges = bd718xx_ldo1_volts,
 509                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
 510                         .vsel_reg = BD718XX_REG_LDO1_VOLT,
 511                         .vsel_mask = BD718XX_LDO1_MASK,
 512                         .vsel_range_reg = BD718XX_REG_LDO1_VOLT,
 513                         .vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
 514                         .linear_range_selectors = bd718xx_ldo1_volt_range_sel,
 515                         .enable_reg = BD718XX_REG_LDO1_VOLT,
 516                         .enable_mask = BD718XX_LDO_EN,
 517                         .owner = THIS_MODULE,
 518                 },
 519                 .init = {
 520                         .reg = BD718XX_REG_LDO1_VOLT,
 521                         .mask = BD718XX_LDO_SEL,
 522                         .val = BD718XX_LDO_SEL,
 523                 },
 524         },
 525         {
 526                 .desc = {
 527                         .name = "ldo2",
 528                         .of_match = of_match_ptr("LDO2"),
 529                         .regulators_node = of_match_ptr("regulators"),
 530                         .id = BD718XX_LDO2,
 531                         .ops = &bd718xx_ldo_regulator_nolinear_ops,
 532                         .type = REGULATOR_VOLTAGE,
 533                         .volt_table = &ldo_2_volts[0],
 534                         .vsel_reg = BD718XX_REG_LDO2_VOLT,
 535                         .vsel_mask = BD718XX_LDO2_MASK,
 536                         .n_voltages = ARRAY_SIZE(ldo_2_volts),
 537                         .enable_reg = BD718XX_REG_LDO2_VOLT,
 538                         .enable_mask = BD718XX_LDO_EN,
 539                         .owner = THIS_MODULE,
 540                 },
 541                 .init = {
 542                         .reg = BD718XX_REG_LDO2_VOLT,
 543                         .mask = BD718XX_LDO_SEL,
 544                         .val = BD718XX_LDO_SEL,
 545                 },
 546         },
 547         {
 548                 .desc = {
 549                         .name = "ldo3",
 550                         .of_match = of_match_ptr("LDO3"),
 551                         .regulators_node = of_match_ptr("regulators"),
 552                         .id = BD718XX_LDO3,
 553                         .ops = &bd718xx_ldo_regulator_ops,
 554                         .type = REGULATOR_VOLTAGE,
 555                         .n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
 556                         .linear_ranges = bd718xx_ldo3_volts,
 557                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
 558                         .vsel_reg = BD718XX_REG_LDO3_VOLT,
 559                         .vsel_mask = BD718XX_LDO3_MASK,
 560                         .enable_reg = BD718XX_REG_LDO3_VOLT,
 561                         .enable_mask = BD718XX_LDO_EN,
 562                         .owner = THIS_MODULE,
 563                 },
 564                 .init = {
 565                         .reg = BD718XX_REG_LDO3_VOLT,
 566                         .mask = BD718XX_LDO_SEL,
 567                         .val = BD718XX_LDO_SEL,
 568                 },
 569         },
 570         {
 571                 .desc = {
 572                         .name = "ldo4",
 573                         .of_match = of_match_ptr("LDO4"),
 574                         .regulators_node = of_match_ptr("regulators"),
 575                         .id = BD718XX_LDO4,
 576                         .ops = &bd718xx_ldo_regulator_ops,
 577                         .type = REGULATOR_VOLTAGE,
 578                         .n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
 579                         .linear_ranges = bd718xx_ldo4_volts,
 580                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
 581                         .vsel_reg = BD718XX_REG_LDO4_VOLT,
 582                         .vsel_mask = BD718XX_LDO4_MASK,
 583                         .enable_reg = BD718XX_REG_LDO4_VOLT,
 584                         .enable_mask = BD718XX_LDO_EN,
 585                         .owner = THIS_MODULE,
 586                 },
 587                 .init = {
 588                         .reg = BD718XX_REG_LDO4_VOLT,
 589                         .mask = BD718XX_LDO_SEL,
 590                         .val = BD718XX_LDO_SEL,
 591                 },
 592         },
 593         {
 594                 .desc = {
 595                         .name = "ldo5",
 596                         .of_match = of_match_ptr("LDO5"),
 597                         .regulators_node = of_match_ptr("regulators"),
 598                         .id = BD718XX_LDO5,
 599                         .ops = &bd718xx_pickable_range_ldo_ops,
 600                         .type = REGULATOR_VOLTAGE,
 601                         .n_voltages = BD71847_LDO5_VOLTAGE_NUM,
 602                         .linear_ranges = bd71847_ldo5_volts,
 603                         .n_linear_ranges = ARRAY_SIZE(bd71847_ldo5_volts),
 604                         .vsel_reg = BD718XX_REG_LDO5_VOLT,
 605                         .vsel_mask = BD71847_LDO5_MASK,
 606                         .vsel_range_reg = BD718XX_REG_LDO5_VOLT,
 607                         .vsel_range_mask = BD71847_LDO5_RANGE_MASK,
 608                         .linear_range_selectors = bd71847_ldo5_volt_range_sel,
 609                         .enable_reg = BD718XX_REG_LDO5_VOLT,
 610                         .enable_mask = BD718XX_LDO_EN,
 611                         .owner = THIS_MODULE,
 612                 },
 613                 .init = {
 614                         .reg = BD718XX_REG_LDO5_VOLT,
 615                         .mask = BD718XX_LDO_SEL,
 616                         .val = BD718XX_LDO_SEL,
 617                 },
 618         },
 619         {
 620                 .desc = {
 621                         .name = "ldo6",
 622                         .of_match = of_match_ptr("LDO6"),
 623                         .regulators_node = of_match_ptr("regulators"),
 624                         .id = BD718XX_LDO6,
 625                         .ops = &bd718xx_ldo_regulator_ops,
 626                         .type = REGULATOR_VOLTAGE,
 627                         .n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
 628                         .linear_ranges = bd718xx_ldo6_volts,
 629                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
 630                         /* LDO6 is supplied by buck5 */
 631                         .supply_name = "buck5",
 632                         .vsel_reg = BD718XX_REG_LDO6_VOLT,
 633                         .vsel_mask = BD718XX_LDO6_MASK,
 634                         .enable_reg = BD718XX_REG_LDO6_VOLT,
 635                         .enable_mask = BD718XX_LDO_EN,
 636                         .owner = THIS_MODULE,
 637                 },
 638                 .init = {
 639                         .reg = BD718XX_REG_LDO6_VOLT,
 640                         .mask = BD718XX_LDO_SEL,
 641                         .val = BD718XX_LDO_SEL,
 642                 },
 643         },
 644 };
 645
 646 static const struct bd718xx_regulator_data bd71837_regulators[] = {
 647         {
 648                 .desc = {
 649                         .name = "buck1",
 650                         .of_match = of_match_ptr("BUCK1"),
 651                         .regulators_node = of_match_ptr("regulators"),
 652                         .id = BD718XX_BUCK1,
 653                         .ops = &bd718xx_dvs_buck_regulator_ops,
 654                         .type = REGULATOR_VOLTAGE,
 655                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 656                         .linear_ranges = bd718xx_dvs_buck_volts,
 657                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 658                         .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN,
 659                         .vsel_mask = DVS_BUCK_RUN_MASK,
 660                         .enable_reg = BD718XX_REG_BUCK1_CTRL,
 661                         .enable_mask = BD718XX_BUCK_EN,
 662                         .owner = THIS_MODULE,
 663                 },
 664                 .init = {
 665                         .reg = BD718XX_REG_BUCK1_CTRL,
 666                         .mask = BD718XX_BUCK_SEL,
 667                         .val = BD718XX_BUCK_SEL,
 668                 },
 669         },
 670         {
 671                 .desc = {
 672                         .name = "buck2",
 673                         .of_match = of_match_ptr("BUCK2"),
 674                         .regulators_node = of_match_ptr("regulators"),
 675                         .id = BD718XX_BUCK2,
 676                         .ops = &bd718xx_dvs_buck_regulator_ops,
 677                         .type = REGULATOR_VOLTAGE,
 678                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 679                         .linear_ranges = bd718xx_dvs_buck_volts,
 680                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 681                         .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN,
 682                         .vsel_mask = DVS_BUCK_RUN_MASK,
 683                         .enable_reg = BD718XX_REG_BUCK2_CTRL,
 684                         .enable_mask = BD718XX_BUCK_EN,
 685                         .owner = THIS_MODULE,
 686                 },
 687                 .init = {
 688                         .reg = BD718XX_REG_BUCK2_CTRL,
 689                         .mask = BD718XX_BUCK_SEL,
 690                         .val = BD718XX_BUCK_SEL,
 691                 },
 692         },
 693         {
 694                 .desc = {
 695                         .name = "buck3",
 696                         .of_match = of_match_ptr("BUCK3"),
 697                         .regulators_node = of_match_ptr("regulators"),
 698                         .id = BD718XX_BUCK3,
 699                         .ops = &bd718xx_dvs_buck_regulator_ops,
 700                         .type = REGULATOR_VOLTAGE,
 701                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 702                         .linear_ranges = bd718xx_dvs_buck_volts,
 703                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 704                         .vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
 705                         .vsel_mask = DVS_BUCK_RUN_MASK,
 706                         .enable_reg = BD71837_REG_BUCK3_CTRL,
 707                         .enable_mask = BD718XX_BUCK_EN,
 708                         .owner = THIS_MODULE,
 709                 },
 710                 .init = {
 711                         .reg = BD71837_REG_BUCK3_CTRL,
 712                         .mask = BD718XX_BUCK_SEL,
 713                         .val = BD718XX_BUCK_SEL,
 714                 },
 715         },
 716         {
 717                 .desc = {
 718                         .name = "buck4",
 719                         .of_match = of_match_ptr("BUCK4"),
 720                         .regulators_node = of_match_ptr("regulators"),
 721                         .id = BD718XX_BUCK4,
 722                         .ops = &bd718xx_dvs_buck_regulator_ops,
 723                         .type = REGULATOR_VOLTAGE,
 724                         .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM,
 725                         .linear_ranges = bd718xx_dvs_buck_volts,
 726                         .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts),
 727                         .vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
 728                         .vsel_mask = DVS_BUCK_RUN_MASK,
 729                         .enable_reg = BD71837_REG_BUCK4_CTRL,
 730                         .enable_mask = BD718XX_BUCK_EN,
 731                         .owner = THIS_MODULE,
 732                 },
 733                 .init = {
 734                         .reg = BD71837_REG_BUCK4_CTRL,
 735                         .mask = BD718XX_BUCK_SEL,
 736                         .val = BD718XX_BUCK_SEL,
 737                 },
 738         },
 739         {
 740                 .desc = {
 741                         .name = "buck5",
 742                         .of_match = of_match_ptr("BUCK5"),
 743                         .regulators_node = of_match_ptr("regulators"),
 744                         .id = BD718XX_BUCK5,
 745                         .ops = &bd718xx_pickable_range_buck_ops,
 746                         .type = REGULATOR_VOLTAGE,
 747                         .n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
 748                         .linear_ranges = bd71837_buck5_volts,
 749                         .n_linear_ranges =
 750                                 ARRAY_SIZE(bd71837_buck5_volts),
 751                         .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 752                         .vsel_mask = BD71837_BUCK5_MASK,
 753                         .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT,
 754                         .vsel_range_mask = BD71837_BUCK5_RANGE_MASK,
 755                         .linear_range_selectors = bd71837_buck5_volt_range_sel,
 756                         .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 757                         .enable_mask = BD718XX_BUCK_EN,
 758                         .owner = THIS_MODULE,
 759                 },
 760                 .init = {
 761                         .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL,
 762                         .mask = BD718XX_BUCK_SEL,
 763                         .val = BD718XX_BUCK_SEL,
 764                 },
 765         },
 766         {
 767                 .desc = {
 768                         .name = "buck6",
 769                         .of_match = of_match_ptr("BUCK6"),
 770                         .regulators_node = of_match_ptr("regulators"),
 771                         .id = BD718XX_BUCK6,
 772                         .ops = &bd718xx_buck_regulator_ops,
 773                         .type = REGULATOR_VOLTAGE,
 774                         .n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
 775                         .linear_ranges = bd71837_buck6_volts,
 776                         .n_linear_ranges =
 777                                 ARRAY_SIZE(bd71837_buck6_volts),
 778                         .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT,
 779                         .vsel_mask = BD71837_BUCK6_MASK,
 780                         .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 781                         .enable_mask = BD718XX_BUCK_EN,
 782                         .owner = THIS_MODULE,
 783                 },
 784                 .init = {
 785                         .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL,
 786                         .mask = BD718XX_BUCK_SEL,
 787                         .val = BD718XX_BUCK_SEL,
 788                 },
 789         },
 790         {
 791                 .desc = {
 792                         .name = "buck7",
 793                         .of_match = of_match_ptr("BUCK7"),
 794                         .regulators_node = of_match_ptr("regulators"),
 795                         .id = BD718XX_BUCK7,
 796                         .ops = &bd718xx_buck_regulator_nolinear_ops,
 797                         .type = REGULATOR_VOLTAGE,
 798                         .volt_table = &bd718xx_3rd_nodvs_buck_volts[0],
 799                         .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts),
 800                         .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT,
 801                         .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK,
 802                         .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 803                         .enable_mask = BD718XX_BUCK_EN,
 804                         .owner = THIS_MODULE,
 805                 },
 806                 .init = {
 807                         .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL,
 808                         .mask = BD718XX_BUCK_SEL,
 809                         .val = BD718XX_BUCK_SEL,
 810                 },
 811         },
 812         {
 813                 .desc = {
 814                         .name = "buck8",
 815                         .of_match = of_match_ptr("BUCK8"),
 816                         .regulators_node = of_match_ptr("regulators"),
 817                         .id = BD718XX_BUCK8,
 818                         .ops = &bd718xx_buck_regulator_ops,
 819                         .type = REGULATOR_VOLTAGE,
 820                         .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM,
 821                         .linear_ranges = bd718xx_4th_nodvs_buck_volts,
 822                         .n_linear_ranges =
 823                                 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts),
 824                         .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT,
 825                         .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK,
 826                         .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 827                         .enable_mask = BD718XX_BUCK_EN,
 828                         .owner = THIS_MODULE,
 829                 },
 830                 .init = {
 831                         .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL,
 832                         .mask = BD718XX_BUCK_SEL,
 833                         .val = BD718XX_BUCK_SEL,
 834                 },
 835         },
 836         {
 837                 .desc = {
 838                         .name = "ldo1",
 839                         .of_match = of_match_ptr("LDO1"),
 840                         .regulators_node = of_match_ptr("regulators"),
 841                         .id = BD718XX_LDO1,
 842                         .ops = &bd718xx_pickable_range_ldo_ops,
 843                         .type = REGULATOR_VOLTAGE,
 844                         .n_voltages = BD718XX_LDO1_VOLTAGE_NUM,
 845                         .linear_ranges = bd718xx_ldo1_volts,
 846                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts),
 847                         .vsel_reg = BD718XX_REG_LDO1_VOLT,
 848                         .vsel_mask = BD718XX_LDO1_MASK,
 849                         .vsel_range_reg = BD718XX_REG_LDO1_VOLT,
 850                         .vsel_range_mask = BD718XX_LDO1_RANGE_MASK,
 851                         .linear_range_selectors = bd718xx_ldo1_volt_range_sel,
 852                         .enable_reg = BD718XX_REG_LDO1_VOLT,
 853                         .enable_mask = BD718XX_LDO_EN,
 854                         .owner = THIS_MODULE,
 855                 },
 856                 .init = {
 857                         .reg = BD718XX_REG_LDO1_VOLT,
 858                         .mask = BD718XX_LDO_SEL,
 859                         .val = BD718XX_LDO_SEL,
 860                 },
 861         },
 862         {
 863                 .desc = {
 864                         .name = "ldo2",
 865                         .of_match = of_match_ptr("LDO2"),
 866                         .regulators_node = of_match_ptr("regulators"),
 867                         .id = BD718XX_LDO2,
 868                         .ops = &bd718xx_ldo_regulator_nolinear_ops,
 869                         .type = REGULATOR_VOLTAGE,
 870                         .volt_table = &ldo_2_volts[0],
 871                         .vsel_reg = BD718XX_REG_LDO2_VOLT,
 872                         .vsel_mask = BD718XX_LDO2_MASK,
 873                         .n_voltages = ARRAY_SIZE(ldo_2_volts),
 874                         .enable_reg = BD718XX_REG_LDO2_VOLT,
 875                         .enable_mask = BD718XX_LDO_EN,
 876                         .owner = THIS_MODULE,
 877                 },
 878                 .init = {
 879                         .reg = BD718XX_REG_LDO2_VOLT,
 880                         .mask = BD718XX_LDO_SEL,
 881                         .val = BD718XX_LDO_SEL,
 882                 },
 883         },
 884         {
 885                 .desc = {
 886                         .name = "ldo3",
 887                         .of_match = of_match_ptr("LDO3"),
 888                         .regulators_node = of_match_ptr("regulators"),
 889                         .id = BD718XX_LDO3,
 890                         .ops = &bd718xx_ldo_regulator_ops,
 891                         .type = REGULATOR_VOLTAGE,
 892                         .n_voltages = BD718XX_LDO3_VOLTAGE_NUM,
 893                         .linear_ranges = bd718xx_ldo3_volts,
 894                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts),
 895                         .vsel_reg = BD718XX_REG_LDO3_VOLT,
 896                         .vsel_mask = BD718XX_LDO3_MASK,
 897                         .enable_reg = BD718XX_REG_LDO3_VOLT,
 898                         .enable_mask = BD718XX_LDO_EN,
 899                         .owner = THIS_MODULE,
 900                 },
 901                 .init = {
 902                         .reg = BD718XX_REG_LDO3_VOLT,
 903                         .mask = BD718XX_LDO_SEL,
 904                         .val = BD718XX_LDO_SEL,
 905                 },
 906         },
 907         {
 908                 .desc = {
 909                         .name = "ldo4",
 910                         .of_match = of_match_ptr("LDO4"),
 911                         .regulators_node = of_match_ptr("regulators"),
 912                         .id = BD718XX_LDO4,
 913                         .ops = &bd718xx_ldo_regulator_ops,
 914                         .type = REGULATOR_VOLTAGE,
 915                         .n_voltages = BD718XX_LDO4_VOLTAGE_NUM,
 916                         .linear_ranges = bd718xx_ldo4_volts,
 917                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts),
 918                         .vsel_reg = BD718XX_REG_LDO4_VOLT,
 919                         .vsel_mask = BD718XX_LDO4_MASK,
 920                         .enable_reg = BD718XX_REG_LDO4_VOLT,
 921                         .enable_mask = BD718XX_LDO_EN,
 922                         .owner = THIS_MODULE,
 923                 },
 924                 .init = {
 925                         .reg = BD718XX_REG_LDO4_VOLT,
 926                         .mask = BD718XX_LDO_SEL,
 927                         .val = BD718XX_LDO_SEL,
 928                 },
 929         },
 930         {
 931                 .desc = {
 932                         .name = "ldo5",
 933                         .of_match = of_match_ptr("LDO5"),
 934                         .regulators_node = of_match_ptr("regulators"),
 935                         .id = BD718XX_LDO5,
 936                         .ops = &bd718xx_ldo_regulator_ops,
 937                         .type = REGULATOR_VOLTAGE,
 938                         .n_voltages = BD71837_LDO5_VOLTAGE_NUM,
 939                         .linear_ranges = bd71837_ldo5_volts,
 940                         .n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_volts),
 941                         /* LDO5 is supplied by buck6 */
 942                         .supply_name = "buck6",
 943                         .vsel_reg = BD718XX_REG_LDO5_VOLT,
 944                         .vsel_mask = BD71837_LDO5_MASK,
 945                         .enable_reg = BD718XX_REG_LDO5_VOLT,
 946                         .enable_mask = BD718XX_LDO_EN,
 947                         .owner = THIS_MODULE,
 948                 },
 949                 .init = {
 950                         .reg = BD718XX_REG_LDO5_VOLT,
 951                         .mask = BD718XX_LDO_SEL,
 952                         .val = BD718XX_LDO_SEL,
 953                 },
 954                 .additional_inits = bd71837_ldo5_inits,
 955                 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo5_inits),
 956         },
 957         {
 958                 .desc = {
 959                         .name = "ldo6",
 960                         .of_match = of_match_ptr("LDO6"),
 961                         .regulators_node = of_match_ptr("regulators"),
 962                         .id = BD718XX_LDO6,
 963                         .ops = &bd718xx_ldo_regulator_ops,
 964                         .type = REGULATOR_VOLTAGE,
 965                         .n_voltages = BD718XX_LDO6_VOLTAGE_NUM,
 966                         .linear_ranges = bd718xx_ldo6_volts,
 967                         .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts),
 968                         /* LDO6 is supplied by buck7 */
 969                         .supply_name = "buck7",
 970                         .vsel_reg = BD718XX_REG_LDO6_VOLT,
 971                         .vsel_mask = BD718XX_LDO6_MASK,
 972                         .enable_reg = BD718XX_REG_LDO6_VOLT,
 973                         .enable_mask = BD718XX_LDO_EN,
 974                         .owner = THIS_MODULE,
 975                 },
 976                 .init = {
 977                         .reg = BD718XX_REG_LDO6_VOLT,
 978                         .mask = BD718XX_LDO_SEL,
 979                         .val = BD718XX_LDO_SEL,
 980                 },
 981                 .additional_inits = bd71837_ldo6_inits,
 982                 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo6_inits),
 983         },
 984         {
 985                 .desc = {
 986                         .name = "ldo7",
 987                         .of_match = of_match_ptr("LDO7"),
 988                         .regulators_node = of_match_ptr("regulators"),
 989                         .id = BD718XX_LDO7,
 990                         .ops = &bd718xx_ldo_regulator_ops,
 991                         .type = REGULATOR_VOLTAGE,
 992                         .n_voltages = BD71837_LDO7_VOLTAGE_NUM,
 993                         .linear_ranges = bd71837_ldo7_volts,
 994                         .n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_volts),
 995                         .vsel_reg = BD71837_REG_LDO7_VOLT,
 996                         .vsel_mask = BD71837_LDO7_MASK,
 997                         .enable_reg = BD71837_REG_LDO7_VOLT,
 998                         .enable_mask = BD718XX_LDO_EN,
 999                         .owner = THIS_MODULE,
1000                 },
1001                 .init = {
1002                         .reg = BD71837_REG_LDO7_VOLT,
1003                         .mask = BD718XX_LDO_SEL,
1004                         .val = BD718XX_LDO_SEL,
1005                 },
1006         },
1007 };
1008
1009 struct bd718xx_pmic_inits {
1010         const struct bd718xx_regulator_data (*r_datas)[];
1011         unsigned int r_amount;
1012 };
1013
1014 static int bd718xx_probe(struct platform_device *pdev)
1015 {
1016         struct bd718xx *mfd;
1017         struct regulator_config config = { 0 };
1018         struct bd718xx_pmic_inits pmic_regulators[] = {
1019                 [BD718XX_TYPE_BD71837] = {
1020                         .r_datas = &bd71837_regulators,
1021                         .r_amount = ARRAY_SIZE(bd71837_regulators),
1022                 },
1023                 [BD718XX_TYPE_BD71847] = {
1024                         .r_datas = &bd71847_regulators,
1025                         .r_amount = ARRAY_SIZE(bd71847_regulators),
1026                 },
1027         };
1028
1029         int i, j, err;
1030
1031         mfd = dev_get_drvdata(pdev->dev.parent);
1032         if (!mfd) {
1033                 dev_err(&pdev->dev, "No MFD driver data\n");
1034                 err = -EINVAL;
1035                 goto err;
1036         }
1037
1038         if (mfd->chip_type >= BD718XX_TYPE_AMOUNT ||
1039             !pmic_regulators[mfd->chip_type].r_datas) {
1040                 dev_err(&pdev->dev, "Unsupported chip type\n");
1041                 err = -EINVAL;
1042                 goto err;
1043         }
1044
1045         /* Register LOCK release */
1046         err = regmap_update_bits(mfd->regmap, BD718XX_REG_REGLOCK,
1047                                  (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
1048         if (err) {
1049                 dev_err(&pdev->dev, "Failed to unlock PMIC (%d)\n", err);
1050                 goto err;
1051         } else {
1052                 dev_dbg(&pdev->dev, "Unlocked lock register 0x%x\n",
1053                         BD718XX_REG_REGLOCK);
1054         }
1055
1056         for (i = 0; i < pmic_regulators[mfd->chip_type].r_amount; i++) {
1057
1058                 const struct regulator_desc *desc;
1059                 struct regulator_dev *rdev;
1060                 const struct bd718xx_regulator_data *r;
1061
1062                 r = &(*pmic_regulators[mfd->chip_type].r_datas)[i];
1063                 desc = &r->desc;
1064
1065                 config.dev = pdev->dev.parent;
1066                 config.regmap = mfd->regmap;
1067
1068                 rdev = devm_regulator_register(&pdev->dev, desc, &config);
1069                 if (IS_ERR(rdev)) {
1070                         dev_err(&pdev->dev,
1071                                 "failed to register %s regulator\n",
1072                                 desc->name);
1073                         err = PTR_ERR(rdev);
1074                         goto err;
1075                 }
1076                 /* Regulator register gets the regulator constraints and
1077                  * applies them (set_machine_constraints). This should have
1078                  * turned the control register(s) to correct values and we
1079                  * can now switch the control from PMIC state machine to the
1080                  * register interface
1081                  */
1082                 err = regmap_update_bits(mfd->regmap, r->init.reg,
1083                                          r->init.mask, r->init.val);
1084                 if (err) {
1085                         dev_err(&pdev->dev,
1086                                 "Failed to write BUCK/LDO SEL bit for (%s)\n",
1087                                 desc->name);
1088                         goto err;
1089                 }
1090                 for (j = 0; j < r->additional_init_amnt; j++) {
1091                         err = regmap_update_bits(mfd->regmap,
1092                                                  r->additional_inits[j].reg,
1093                                                  r->additional_inits[j].mask,
1094                                                  r->additional_inits[j].val);
1095                         if (err) {
1096                                 dev_err(&pdev->dev,
1097                                         "Buck (%s) initialization failed\n",
1098                                         desc->name);
1099                                 goto err;
1100                         }
1101                 }
1102         }
1103
1104 err:
1105         return err;
1106 }
1107
1108 static struct platform_driver bd718xx_regulator = {
1109         .driver = {
1110                 .name = "bd718xx-pmic",
1111         },
1112         .probe = bd718xx_probe,
1113 };
1114
1115 module_platform_driver(bd718xx_regulator);
1116
1117 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
1118 MODULE_DESCRIPTION("BD71837/BD71847 voltage regulator driver");
1119 MODULE_LICENSE("GPL");