1 // SPDX-License-Identifier: GPL-2.0-only
3 * Driver for Atmel AT32 and AT91 SPI Controllers
5 * Copyright (C) 2006 Atmel Corporation
8 #include <linux/kernel.h>
10 #include <linux/module.h>
11 #include <linux/platform_device.h>
12 #include <linux/delay.h>
13 #include <linux/dma-mapping.h>
14 #include <linux/dmaengine.h>
15 #include <linux/err.h>
16 #include <linux/interrupt.h>
17 #include <linux/spi/spi.h>
18 #include <linux/slab.h>
19 #include <linux/platform_data/dma-atmel.h>
23 #include <linux/gpio/consumer.h>
24 #include <linux/pinctrl/consumer.h>
25 #include <linux/pm_runtime.h>
26 #include <trace/events/spi.h>
28 /* SPI register offsets */
31 #define SPI_RDR 0x0008
32 #define SPI_TDR 0x000c
34 #define SPI_IER 0x0014
35 #define SPI_IDR 0x0018
36 #define SPI_IMR 0x001c
37 #define SPI_CSR0 0x0030
38 #define SPI_CSR1 0x0034
39 #define SPI_CSR2 0x0038
40 #define SPI_CSR3 0x003c
41 #define SPI_FMR 0x0040
42 #define SPI_FLR 0x0044
43 #define SPI_VERSION 0x00fc
44 #define SPI_RPR 0x0100
45 #define SPI_RCR 0x0104
46 #define SPI_TPR 0x0108
47 #define SPI_TCR 0x010c
48 #define SPI_RNPR 0x0110
49 #define SPI_RNCR 0x0114
50 #define SPI_TNPR 0x0118
51 #define SPI_TNCR 0x011c
52 #define SPI_PTCR 0x0120
53 #define SPI_PTSR 0x0124
56 #define SPI_SPIEN_OFFSET 0
57 #define SPI_SPIEN_SIZE 1
58 #define SPI_SPIDIS_OFFSET 1
59 #define SPI_SPIDIS_SIZE 1
60 #define SPI_SWRST_OFFSET 7
61 #define SPI_SWRST_SIZE 1
62 #define SPI_LASTXFER_OFFSET 24
63 #define SPI_LASTXFER_SIZE 1
64 #define SPI_TXFCLR_OFFSET 16
65 #define SPI_TXFCLR_SIZE 1
66 #define SPI_RXFCLR_OFFSET 17
67 #define SPI_RXFCLR_SIZE 1
68 #define SPI_FIFOEN_OFFSET 30
69 #define SPI_FIFOEN_SIZE 1
70 #define SPI_FIFODIS_OFFSET 31
71 #define SPI_FIFODIS_SIZE 1
74 #define SPI_MSTR_OFFSET 0
75 #define SPI_MSTR_SIZE 1
76 #define SPI_PS_OFFSET 1
78 #define SPI_PCSDEC_OFFSET 2
79 #define SPI_PCSDEC_SIZE 1
80 #define SPI_FDIV_OFFSET 3
81 #define SPI_FDIV_SIZE 1
82 #define SPI_MODFDIS_OFFSET 4
83 #define SPI_MODFDIS_SIZE 1
84 #define SPI_WDRBT_OFFSET 5
85 #define SPI_WDRBT_SIZE 1
86 #define SPI_LLB_OFFSET 7
87 #define SPI_LLB_SIZE 1
88 #define SPI_PCS_OFFSET 16
89 #define SPI_PCS_SIZE 4
90 #define SPI_DLYBCS_OFFSET 24
91 #define SPI_DLYBCS_SIZE 8
93 /* Bitfields in RDR */
94 #define SPI_RD_OFFSET 0
95 #define SPI_RD_SIZE 16
97 /* Bitfields in TDR */
98 #define SPI_TD_OFFSET 0
99 #define SPI_TD_SIZE 16
101 /* Bitfields in SR */
102 #define SPI_RDRF_OFFSET 0
103 #define SPI_RDRF_SIZE 1
104 #define SPI_TDRE_OFFSET 1
105 #define SPI_TDRE_SIZE 1
106 #define SPI_MODF_OFFSET 2
107 #define SPI_MODF_SIZE 1
108 #define SPI_OVRES_OFFSET 3
109 #define SPI_OVRES_SIZE 1
110 #define SPI_ENDRX_OFFSET 4
111 #define SPI_ENDRX_SIZE 1
112 #define SPI_ENDTX_OFFSET 5
113 #define SPI_ENDTX_SIZE 1
114 #define SPI_RXBUFF_OFFSET 6
115 #define SPI_RXBUFF_SIZE 1
116 #define SPI_TXBUFE_OFFSET 7
117 #define SPI_TXBUFE_SIZE 1
118 #define SPI_NSSR_OFFSET 8
119 #define SPI_NSSR_SIZE 1
120 #define SPI_TXEMPTY_OFFSET 9
121 #define SPI_TXEMPTY_SIZE 1
122 #define SPI_SPIENS_OFFSET 16
123 #define SPI_SPIENS_SIZE 1
124 #define SPI_TXFEF_OFFSET 24
125 #define SPI_TXFEF_SIZE 1
126 #define SPI_TXFFF_OFFSET 25
127 #define SPI_TXFFF_SIZE 1
128 #define SPI_TXFTHF_OFFSET 26
129 #define SPI_TXFTHF_SIZE 1
130 #define SPI_RXFEF_OFFSET 27
131 #define SPI_RXFEF_SIZE 1
132 #define SPI_RXFFF_OFFSET 28
133 #define SPI_RXFFF_SIZE 1
134 #define SPI_RXFTHF_OFFSET 29
135 #define SPI_RXFTHF_SIZE 1
136 #define SPI_TXFPTEF_OFFSET 30
137 #define SPI_TXFPTEF_SIZE 1
138 #define SPI_RXFPTEF_OFFSET 31
139 #define SPI_RXFPTEF_SIZE 1
141 /* Bitfields in CSR0 */
142 #define SPI_CPOL_OFFSET 0
143 #define SPI_CPOL_SIZE 1
144 #define SPI_NCPHA_OFFSET 1
145 #define SPI_NCPHA_SIZE 1
146 #define SPI_CSAAT_OFFSET 3
147 #define SPI_CSAAT_SIZE 1
148 #define SPI_BITS_OFFSET 4
149 #define SPI_BITS_SIZE 4
150 #define SPI_SCBR_OFFSET 8
151 #define SPI_SCBR_SIZE 8
152 #define SPI_DLYBS_OFFSET 16
153 #define SPI_DLYBS_SIZE 8
154 #define SPI_DLYBCT_OFFSET 24
155 #define SPI_DLYBCT_SIZE 8
157 /* Bitfields in RCR */
158 #define SPI_RXCTR_OFFSET 0
159 #define SPI_RXCTR_SIZE 16
161 /* Bitfields in TCR */
162 #define SPI_TXCTR_OFFSET 0
163 #define SPI_TXCTR_SIZE 16
165 /* Bitfields in RNCR */
166 #define SPI_RXNCR_OFFSET 0
167 #define SPI_RXNCR_SIZE 16
169 /* Bitfields in TNCR */
170 #define SPI_TXNCR_OFFSET 0
171 #define SPI_TXNCR_SIZE 16
173 /* Bitfields in PTCR */
174 #define SPI_RXTEN_OFFSET 0
175 #define SPI_RXTEN_SIZE 1
176 #define SPI_RXTDIS_OFFSET 1
177 #define SPI_RXTDIS_SIZE 1
178 #define SPI_TXTEN_OFFSET 8
179 #define SPI_TXTEN_SIZE 1
180 #define SPI_TXTDIS_OFFSET 9
181 #define SPI_TXTDIS_SIZE 1
183 /* Bitfields in FMR */
184 #define SPI_TXRDYM_OFFSET 0
185 #define SPI_TXRDYM_SIZE 2
186 #define SPI_RXRDYM_OFFSET 4
187 #define SPI_RXRDYM_SIZE 2
188 #define SPI_TXFTHRES_OFFSET 16
189 #define SPI_TXFTHRES_SIZE 6
190 #define SPI_RXFTHRES_OFFSET 24
191 #define SPI_RXFTHRES_SIZE 6
193 /* Bitfields in FLR */
194 #define SPI_TXFL_OFFSET 0
195 #define SPI_TXFL_SIZE 6
196 #define SPI_RXFL_OFFSET 16
197 #define SPI_RXFL_SIZE 6
199 /* Constants for BITS */
200 #define SPI_BITS_8_BPT 0
201 #define SPI_BITS_9_BPT 1
202 #define SPI_BITS_10_BPT 2
203 #define SPI_BITS_11_BPT 3
204 #define SPI_BITS_12_BPT 4
205 #define SPI_BITS_13_BPT 5
206 #define SPI_BITS_14_BPT 6
207 #define SPI_BITS_15_BPT 7
208 #define SPI_BITS_16_BPT 8
209 #define SPI_ONE_DATA 0
210 #define SPI_TWO_DATA 1
211 #define SPI_FOUR_DATA 2
213 /* Bit manipulation macros */
214 #define SPI_BIT(name) \
215 (1 << SPI_##name##_OFFSET)
216 #define SPI_BF(name, value) \
217 (((value) & ((1 << SPI_##name##_SIZE) - 1)) << SPI_##name##_OFFSET)
218 #define SPI_BFEXT(name, value) \
219 (((value) >> SPI_##name##_OFFSET) & ((1 << SPI_##name##_SIZE) - 1))
220 #define SPI_BFINS(name, value, old) \
221 (((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
222 | SPI_BF(name, value))
224 /* Register access macros */
226 #define spi_readl(port, reg) \
227 __raw_readl((port)->regs + SPI_##reg)
228 #define spi_writel(port, reg, value) \
229 __raw_writel((value), (port)->regs + SPI_##reg)
231 #define spi_readw(port, reg) \
232 __raw_readw((port)->regs + SPI_##reg)
233 #define spi_writew(port, reg, value) \
234 __raw_writew((value), (port)->regs + SPI_##reg)
236 #define spi_readb(port, reg) \
237 __raw_readb((port)->regs + SPI_##reg)
238 #define spi_writeb(port, reg, value) \
239 __raw_writeb((value), (port)->regs + SPI_##reg)
241 #define spi_readl(port, reg) \
242 readl_relaxed((port)->regs + SPI_##reg)
243 #define spi_writel(port, reg, value) \
244 writel_relaxed((value), (port)->regs + SPI_##reg)
246 #define spi_readw(port, reg) \
247 readw_relaxed((port)->regs + SPI_##reg)
248 #define spi_writew(port, reg, value) \
249 writew_relaxed((value), (port)->regs + SPI_##reg)
251 #define spi_readb(port, reg) \
252 readb_relaxed((port)->regs + SPI_##reg)
253 #define spi_writeb(port, reg, value) \
254 writeb_relaxed((value), (port)->regs + SPI_##reg)
256 /* use PIO for small transfers, avoiding DMA setup/teardown overhead and
257 * cache operations; better heuristics consider wordsize and bitrate.
259 #define DMA_MIN_BYTES 16
261 #define SPI_DMA_TIMEOUT (msecs_to_jiffies(1000))
263 #define AUTOSUSPEND_TIMEOUT 2000
265 struct atmel_spi_caps {
268 bool has_dma_support;
269 bool has_pdc_support;
273 * The core SPI transfer engine just talks to a register bank to set up
274 * DMA transfers; transfer queue progress is driven by IRQs. The clock
275 * framework provides the base clock, subdivided for each spi_device.
285 struct platform_device *pdev;
286 unsigned long spi_clk;
288 struct spi_transfer *current_transfer;
289 int current_remaining_bytes;
291 dma_addr_t dma_addr_rx_bbuf;
292 dma_addr_t dma_addr_tx_bbuf;
296 struct completion xfer_completion;
298 struct atmel_spi_caps caps;
310 /* Controller-specific per-slave state */
311 struct atmel_spi_device {
312 struct gpio_desc *npcs_pin;
316 #define SPI_MAX_DMA_XFER 65535 /* true for both PDC and DMA */
317 #define INVALID_DMA_ADDRESS 0xffffffff
320 * Version 2 of the SPI controller has
322 * - SPI_MR.DIV32 may become FDIV or must-be-zero (here: always zero)
323 * - SPI_SR.TXEMPTY, SPI_SR.NSSR (and corresponding irqs)
325 * - SPI_CSRx.SBCR allows faster clocking
327 static bool atmel_spi_is_v2(struct atmel_spi *as)
329 return as->caps.is_spi2;
333 * Earlier SPI controllers (e.g. on at91rm9200) have a design bug whereby
334 * they assume that spi slave device state will not change on deselect, so
335 * that automagic deselection is OK. ("NPCSx rises if no data is to be
336 * transmitted") Not so! Workaround uses nCSx pins as GPIOs; or newer
337 * controllers have CSAAT and friends.
339 * Since the CSAAT functionality is a bit weird on newer controllers as
340 * well, we use GPIO to control nCSx pins on all controllers, updating
341 * MR.PCS to avoid confusing the controller. Using GPIOs also lets us
342 * support active-high chipselects despite the controller's belief that
343 * only active-low devices/systems exists.
345 * However, at91rm9200 has a second erratum whereby nCS0 doesn't work
346 * right when driven with GPIO. ("Mode Fault does not allow more than one
347 * Master on Chip Select 0.") No workaround exists for that ... so for
348 * nCS0 on that chip, we (a) don't use the GPIO, (b) can't support CS_HIGH,
349 * and (c) will trigger that first erratum in some cases.
352 static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
354 struct atmel_spi_device *asd = spi->controller_state;
357 if (atmel_spi_is_v2(as)) {
358 spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
359 /* For the low SPI version, there is a issue that PDC transfer
360 * on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
362 spi_writel(as, CSR0, asd->csr);
363 if (as->caps.has_wdrbt) {
365 SPI_BF(PCS, ~(0x01 << spi->chip_select))
371 SPI_BF(PCS, ~(0x01 << spi->chip_select))
376 mr = spi_readl(as, MR);
377 if (as->use_cs_gpios)
378 gpiod_set_value(asd->npcs_pin, 1);
380 u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
384 /* Make sure clock polarity is correct */
385 for (i = 0; i < spi->master->num_chipselect; i++) {
386 csr = spi_readl(as, CSR0 + 4 * i);
387 if ((csr ^ cpol) & SPI_BIT(CPOL))
388 spi_writel(as, CSR0 + 4 * i,
389 csr ^ SPI_BIT(CPOL));
392 mr = spi_readl(as, MR);
393 mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
394 if (as->use_cs_gpios && spi->chip_select != 0)
395 gpiod_set_value(asd->npcs_pin, 1);
396 spi_writel(as, MR, mr);
399 dev_dbg(&spi->dev, "activate NPCS, mr %08x\n", mr);
402 static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
404 struct atmel_spi_device *asd = spi->controller_state;
407 /* only deactivate *this* device; sometimes transfers to
408 * another device may be active when this routine is called.
410 mr = spi_readl(as, MR);
411 if (~SPI_BFEXT(PCS, mr) & (1 << spi->chip_select)) {
412 mr = SPI_BFINS(PCS, 0xf, mr);
413 spi_writel(as, MR, mr);
416 dev_dbg(&spi->dev, "DEactivate NPCS, mr %08x\n", mr);
418 if (!as->use_cs_gpios)
419 spi_writel(as, CR, SPI_BIT(LASTXFER));
420 else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
421 gpiod_set_value(asd->npcs_pin, 0);
424 static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock)
426 spin_lock_irqsave(&as->lock, as->flags);
429 static void atmel_spi_unlock(struct atmel_spi *as) __releases(&as->lock)
431 spin_unlock_irqrestore(&as->lock, as->flags);
434 static inline bool atmel_spi_is_vmalloc_xfer(struct spi_transfer *xfer)
436 return is_vmalloc_addr(xfer->tx_buf) || is_vmalloc_addr(xfer->rx_buf);
439 static inline bool atmel_spi_use_dma(struct atmel_spi *as,
440 struct spi_transfer *xfer)
442 return as->use_dma && xfer->len >= DMA_MIN_BYTES;
445 static bool atmel_spi_can_dma(struct spi_master *master,
446 struct spi_device *spi,
447 struct spi_transfer *xfer)
449 struct atmel_spi *as = spi_master_get_devdata(master);
451 if (IS_ENABLED(CONFIG_SOC_SAM_V4_V5))
452 return atmel_spi_use_dma(as, xfer) &&
453 !atmel_spi_is_vmalloc_xfer(xfer);
455 return atmel_spi_use_dma(as, xfer);
459 static int atmel_spi_dma_slave_config(struct atmel_spi *as,
460 struct dma_slave_config *slave_config,
463 struct spi_master *master = platform_get_drvdata(as->pdev);
466 if (bits_per_word > 8) {
467 slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
468 slave_config->src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
470 slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
471 slave_config->src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
474 slave_config->dst_addr = (dma_addr_t)as->phybase + SPI_TDR;
475 slave_config->src_addr = (dma_addr_t)as->phybase + SPI_RDR;
476 slave_config->src_maxburst = 1;
477 slave_config->dst_maxburst = 1;
478 slave_config->device_fc = false;
481 * This driver uses fixed peripheral select mode (PS bit set to '0' in
482 * the Mode Register).
483 * So according to the datasheet, when FIFOs are available (and
484 * enabled), the Transmit FIFO operates in Multiple Data Mode.
485 * In this mode, up to 2 data, not 4, can be written into the Transmit
486 * Data Register in a single access.
487 * However, the first data has to be written into the lowest 16 bits and
488 * the second data into the highest 16 bits of the Transmit
489 * Data Register. For 8bit data (the most frequent case), it would
490 * require to rework tx_buf so each data would actualy fit 16 bits.
491 * So we'd rather write only one data at the time. Hence the transmit
492 * path works the same whether FIFOs are available (and enabled) or not.
494 slave_config->direction = DMA_MEM_TO_DEV;
495 if (dmaengine_slave_config(master->dma_tx, slave_config)) {
496 dev_err(&as->pdev->dev,
497 "failed to configure tx dma channel\n");
502 * This driver configures the spi controller for master mode (MSTR bit
503 * set to '1' in the Mode Register).
504 * So according to the datasheet, when FIFOs are available (and
505 * enabled), the Receive FIFO operates in Single Data Mode.
506 * So the receive path works the same whether FIFOs are available (and
509 slave_config->direction = DMA_DEV_TO_MEM;
510 if (dmaengine_slave_config(master->dma_rx, slave_config)) {
511 dev_err(&as->pdev->dev,
512 "failed to configure rx dma channel\n");
519 static int atmel_spi_configure_dma(struct spi_master *master,
520 struct atmel_spi *as)
522 struct dma_slave_config slave_config;
523 struct device *dev = &as->pdev->dev;
528 dma_cap_set(DMA_SLAVE, mask);
530 master->dma_tx = dma_request_slave_channel_reason(dev, "tx");
531 if (IS_ERR(master->dma_tx)) {
532 err = PTR_ERR(master->dma_tx);
533 if (err == -EPROBE_DEFER) {
534 dev_warn(dev, "no DMA channel available at the moment\n");
538 "DMA TX channel not available, SPI unable to use DMA\n");
544 * No reason to check EPROBE_DEFER here since we have already requested
545 * tx channel. If it fails here, it's for another reason.
547 master->dma_rx = dma_request_slave_channel(dev, "rx");
549 if (!master->dma_rx) {
551 "DMA RX channel not available, SPI unable to use DMA\n");
556 err = atmel_spi_dma_slave_config(as, &slave_config, 8);
560 dev_info(&as->pdev->dev,
561 "Using %s (tx) and %s (rx) for DMA transfers\n",
562 dma_chan_name(master->dma_tx),
563 dma_chan_name(master->dma_rx));
568 dma_release_channel(master->dma_rx);
569 if (!IS_ERR(master->dma_tx))
570 dma_release_channel(master->dma_tx);
572 master->dma_tx = master->dma_rx = NULL;
576 static void atmel_spi_stop_dma(struct spi_master *master)
579 dmaengine_terminate_all(master->dma_rx);
581 dmaengine_terminate_all(master->dma_tx);
584 static void atmel_spi_release_dma(struct spi_master *master)
586 if (master->dma_rx) {
587 dma_release_channel(master->dma_rx);
588 master->dma_rx = NULL;
590 if (master->dma_tx) {
591 dma_release_channel(master->dma_tx);
592 master->dma_tx = NULL;
596 /* This function is called by the DMA driver from tasklet context */
597 static void dma_callback(void *data)
599 struct spi_master *master = data;
600 struct atmel_spi *as = spi_master_get_devdata(master);
602 if (is_vmalloc_addr(as->current_transfer->rx_buf) &&
603 IS_ENABLED(CONFIG_SOC_SAM_V4_V5)) {
604 memcpy(as->current_transfer->rx_buf, as->addr_rx_bbuf,
605 as->current_transfer->len);
607 complete(&as->xfer_completion);
611 * Next transfer using PIO without FIFO.
613 static void atmel_spi_next_xfer_single(struct spi_master *master,
614 struct spi_transfer *xfer)
616 struct atmel_spi *as = spi_master_get_devdata(master);
617 unsigned long xfer_pos = xfer->len - as->current_remaining_bytes;
619 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_pio\n");
621 /* Make sure data is not remaining in RDR */
623 while (spi_readl(as, SR) & SPI_BIT(RDRF)) {
628 if (xfer->bits_per_word > 8)
629 spi_writel(as, TDR, *(u16 *)(xfer->tx_buf + xfer_pos));
631 spi_writel(as, TDR, *(u8 *)(xfer->tx_buf + xfer_pos));
633 dev_dbg(master->dev.parent,
634 " start pio xfer %p: len %u tx %p rx %p bitpw %d\n",
635 xfer, xfer->len, xfer->tx_buf, xfer->rx_buf,
636 xfer->bits_per_word);
638 /* Enable relevant interrupts */
639 spi_writel(as, IER, SPI_BIT(RDRF) | SPI_BIT(OVRES));
643 * Next transfer using PIO with FIFO.
645 static void atmel_spi_next_xfer_fifo(struct spi_master *master,
646 struct spi_transfer *xfer)
648 struct atmel_spi *as = spi_master_get_devdata(master);
649 u32 current_remaining_data, num_data;
650 u32 offset = xfer->len - as->current_remaining_bytes;
651 const u16 *words = (const u16 *)((u8 *)xfer->tx_buf + offset);
652 const u8 *bytes = (const u8 *)((u8 *)xfer->tx_buf + offset);
656 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_fifo\n");
658 /* Compute the number of data to transfer in the current iteration */
659 current_remaining_data = ((xfer->bits_per_word > 8) ?
660 ((u32)as->current_remaining_bytes >> 1) :
661 (u32)as->current_remaining_bytes);
662 num_data = min(current_remaining_data, as->fifo_size);
664 /* Flush RX and TX FIFOs */
665 spi_writel(as, CR, SPI_BIT(RXFCLR) | SPI_BIT(TXFCLR));
666 while (spi_readl(as, FLR))
669 /* Set RX FIFO Threshold to the number of data to transfer */
670 fifomr = spi_readl(as, FMR);
671 spi_writel(as, FMR, SPI_BFINS(RXFTHRES, num_data, fifomr));
673 /* Clear FIFO flags in the Status Register, especially RXFTHF */
674 (void)spi_readl(as, SR);
677 while (num_data >= 2) {
678 if (xfer->bits_per_word > 8) {
686 spi_writel(as, TDR, (td1 << 16) | td0);
691 if (xfer->bits_per_word > 8)
696 spi_writew(as, TDR, td0);
700 dev_dbg(master->dev.parent,
701 " start fifo xfer %p: len %u tx %p rx %p bitpw %d\n",
702 xfer, xfer->len, xfer->tx_buf, xfer->rx_buf,
703 xfer->bits_per_word);
706 * Enable RX FIFO Threshold Flag interrupt to be notified about
707 * transfer completion.
709 spi_writel(as, IER, SPI_BIT(RXFTHF) | SPI_BIT(OVRES));
713 * Next transfer using PIO.
715 static void atmel_spi_next_xfer_pio(struct spi_master *master,
716 struct spi_transfer *xfer)
718 struct atmel_spi *as = spi_master_get_devdata(master);
721 atmel_spi_next_xfer_fifo(master, xfer);
723 atmel_spi_next_xfer_single(master, xfer);
727 * Submit next transfer for DMA.
729 static int atmel_spi_next_xfer_dma_submit(struct spi_master *master,
730 struct spi_transfer *xfer,
733 struct atmel_spi *as = spi_master_get_devdata(master);
734 struct dma_chan *rxchan = master->dma_rx;
735 struct dma_chan *txchan = master->dma_tx;
736 struct dma_async_tx_descriptor *rxdesc;
737 struct dma_async_tx_descriptor *txdesc;
738 struct dma_slave_config slave_config;
741 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_dma_submit\n");
743 /* Check that the channels are available */
744 if (!rxchan || !txchan)
747 /* release lock for DMA operations */
748 atmel_spi_unlock(as);
752 if (atmel_spi_dma_slave_config(as, &slave_config,
753 xfer->bits_per_word))
756 /* Send both scatterlists */
757 if (atmel_spi_is_vmalloc_xfer(xfer) &&
758 IS_ENABLED(CONFIG_SOC_SAM_V4_V5)) {
759 rxdesc = dmaengine_prep_slave_single(rxchan,
760 as->dma_addr_rx_bbuf,
766 rxdesc = dmaengine_prep_slave_sg(rxchan,
776 if (atmel_spi_is_vmalloc_xfer(xfer) &&
777 IS_ENABLED(CONFIG_SOC_SAM_V4_V5)) {
778 memcpy(as->addr_tx_bbuf, xfer->tx_buf, xfer->len);
779 txdesc = dmaengine_prep_slave_single(txchan,
780 as->dma_addr_tx_bbuf,
781 xfer->len, DMA_MEM_TO_DEV,
785 txdesc = dmaengine_prep_slave_sg(txchan,
795 dev_dbg(master->dev.parent,
796 " start dma xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
797 xfer, xfer->len, xfer->tx_buf, (unsigned long long)xfer->tx_dma,
798 xfer->rx_buf, (unsigned long long)xfer->rx_dma);
800 /* Enable relevant interrupts */
801 spi_writel(as, IER, SPI_BIT(OVRES));
803 /* Put the callback on the RX transfer only, that should finish last */
804 rxdesc->callback = dma_callback;
805 rxdesc->callback_param = master;
807 /* Submit and fire RX and TX with TX last so we're ready to read! */
808 cookie = rxdesc->tx_submit(rxdesc);
809 if (dma_submit_error(cookie))
811 cookie = txdesc->tx_submit(txdesc);
812 if (dma_submit_error(cookie))
814 rxchan->device->device_issue_pending(rxchan);
815 txchan->device->device_issue_pending(txchan);
822 spi_writel(as, IDR, SPI_BIT(OVRES));
823 atmel_spi_stop_dma(master);
829 static void atmel_spi_next_xfer_data(struct spi_master *master,
830 struct spi_transfer *xfer,
835 *rx_dma = xfer->rx_dma + xfer->len - *plen;
836 *tx_dma = xfer->tx_dma + xfer->len - *plen;
837 if (*plen > master->max_dma_len)
838 *plen = master->max_dma_len;
841 static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
842 struct spi_device *spi,
843 struct spi_transfer *xfer)
846 unsigned long bus_hz;
848 /* v1 chips start out at half the peripheral bus speed. */
849 bus_hz = as->spi_clk;
850 if (!atmel_spi_is_v2(as))
854 * Calculate the lowest divider that satisfies the
855 * constraint, assuming div32/fdiv/mbz == 0.
857 scbr = DIV_ROUND_UP(bus_hz, xfer->speed_hz);
860 * If the resulting divider doesn't fit into the
861 * register bitfield, we can't satisfy the constraint.
863 if (scbr >= (1 << SPI_SCBR_SIZE)) {
865 "setup: %d Hz too slow, scbr %u; min %ld Hz\n",
866 xfer->speed_hz, scbr, bus_hz/255);
871 "setup: %d Hz too high, scbr %u; max %ld Hz\n",
872 xfer->speed_hz, scbr, bus_hz);
875 csr = spi_readl(as, CSR0 + 4 * spi->chip_select);
876 csr = SPI_BFINS(SCBR, scbr, csr);
877 spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
883 * Submit next transfer for PDC.
884 * lock is held, spi irq is blocked
886 static void atmel_spi_pdc_next_xfer(struct spi_master *master,
887 struct spi_message *msg,
888 struct spi_transfer *xfer)
890 struct atmel_spi *as = spi_master_get_devdata(master);
892 dma_addr_t tx_dma, rx_dma;
894 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
896 len = as->current_remaining_bytes;
897 atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
898 as->current_remaining_bytes -= len;
900 spi_writel(as, RPR, rx_dma);
901 spi_writel(as, TPR, tx_dma);
903 if (msg->spi->bits_per_word > 8)
905 spi_writel(as, RCR, len);
906 spi_writel(as, TCR, len);
908 dev_dbg(&msg->spi->dev,
909 " start xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
910 xfer, xfer->len, xfer->tx_buf,
911 (unsigned long long)xfer->tx_dma, xfer->rx_buf,
912 (unsigned long long)xfer->rx_dma);
914 if (as->current_remaining_bytes) {
915 len = as->current_remaining_bytes;
916 atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
917 as->current_remaining_bytes -= len;
919 spi_writel(as, RNPR, rx_dma);
920 spi_writel(as, TNPR, tx_dma);
922 if (msg->spi->bits_per_word > 8)
924 spi_writel(as, RNCR, len);
925 spi_writel(as, TNCR, len);
927 dev_dbg(&msg->spi->dev,
928 " next xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
929 xfer, xfer->len, xfer->tx_buf,
930 (unsigned long long)xfer->tx_dma, xfer->rx_buf,
931 (unsigned long long)xfer->rx_dma);
934 /* REVISIT: We're waiting for RXBUFF before we start the next
935 * transfer because we need to handle some difficult timing
936 * issues otherwise. If we wait for TXBUFE in one transfer and
937 * then starts waiting for RXBUFF in the next, it's difficult
938 * to tell the difference between the RXBUFF interrupt we're
939 * actually waiting for and the RXBUFF interrupt of the
942 * It should be doable, though. Just not now...
944 spi_writel(as, IER, SPI_BIT(RXBUFF) | SPI_BIT(OVRES));
945 spi_writel(as, PTCR, SPI_BIT(TXTEN) | SPI_BIT(RXTEN));
949 * For DMA, tx_buf/tx_dma have the same relationship as rx_buf/rx_dma:
950 * - The buffer is either valid for CPU access, else NULL
951 * - If the buffer is valid, so is its DMA address
953 * This driver manages the dma address unless message->is_dma_mapped.
956 atmel_spi_dma_map_xfer(struct atmel_spi *as, struct spi_transfer *xfer)
958 struct device *dev = &as->pdev->dev;
960 xfer->tx_dma = xfer->rx_dma = INVALID_DMA_ADDRESS;
962 /* tx_buf is a const void* where we need a void * for the dma
964 void *nonconst_tx = (void *)xfer->tx_buf;
966 xfer->tx_dma = dma_map_single(dev,
967 nonconst_tx, xfer->len,
969 if (dma_mapping_error(dev, xfer->tx_dma))
973 xfer->rx_dma = dma_map_single(dev,
974 xfer->rx_buf, xfer->len,
976 if (dma_mapping_error(dev, xfer->rx_dma)) {
978 dma_unmap_single(dev,
979 xfer->tx_dma, xfer->len,
987 static void atmel_spi_dma_unmap_xfer(struct spi_master *master,
988 struct spi_transfer *xfer)
990 if (xfer->tx_dma != INVALID_DMA_ADDRESS)
991 dma_unmap_single(master->dev.parent, xfer->tx_dma,
992 xfer->len, DMA_TO_DEVICE);
993 if (xfer->rx_dma != INVALID_DMA_ADDRESS)
994 dma_unmap_single(master->dev.parent, xfer->rx_dma,
995 xfer->len, DMA_FROM_DEVICE);
998 static void atmel_spi_disable_pdc_transfer(struct atmel_spi *as)
1000 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
1004 atmel_spi_pump_single_data(struct atmel_spi *as, struct spi_transfer *xfer)
1008 unsigned long xfer_pos = xfer->len - as->current_remaining_bytes;
1010 if (xfer->bits_per_word > 8) {
1011 rxp16 = (u16 *)(((u8 *)xfer->rx_buf) + xfer_pos);
1012 *rxp16 = spi_readl(as, RDR);
1014 rxp = ((u8 *)xfer->rx_buf) + xfer_pos;
1015 *rxp = spi_readl(as, RDR);
1017 if (xfer->bits_per_word > 8) {
1018 if (as->current_remaining_bytes > 2)
1019 as->current_remaining_bytes -= 2;
1021 as->current_remaining_bytes = 0;
1023 as->current_remaining_bytes--;
1028 atmel_spi_pump_fifo_data(struct atmel_spi *as, struct spi_transfer *xfer)
1030 u32 fifolr = spi_readl(as, FLR);
1031 u32 num_bytes, num_data = SPI_BFEXT(RXFL, fifolr);
1032 u32 offset = xfer->len - as->current_remaining_bytes;
1033 u16 *words = (u16 *)((u8 *)xfer->rx_buf + offset);
1034 u8 *bytes = (u8 *)((u8 *)xfer->rx_buf + offset);
1035 u16 rd; /* RD field is the lowest 16 bits of RDR */
1037 /* Update the number of remaining bytes to transfer */
1038 num_bytes = ((xfer->bits_per_word > 8) ?
1042 if (as->current_remaining_bytes > num_bytes)
1043 as->current_remaining_bytes -= num_bytes;
1045 as->current_remaining_bytes = 0;
1047 /* Handle odd number of bytes when data are more than 8bit width */
1048 if (xfer->bits_per_word > 8)
1049 as->current_remaining_bytes &= ~0x1;
1053 rd = spi_readl(as, RDR);
1054 if (xfer->bits_per_word > 8)
1064 * Must update "current_remaining_bytes" to keep track of data
1068 atmel_spi_pump_pio_data(struct atmel_spi *as, struct spi_transfer *xfer)
1071 atmel_spi_pump_fifo_data(as, xfer);
1073 atmel_spi_pump_single_data(as, xfer);
1078 * No need for locking in this Interrupt handler: done_status is the
1079 * only information modified.
1082 atmel_spi_pio_interrupt(int irq, void *dev_id)
1084 struct spi_master *master = dev_id;
1085 struct atmel_spi *as = spi_master_get_devdata(master);
1086 u32 status, pending, imr;
1087 struct spi_transfer *xfer;
1090 imr = spi_readl(as, IMR);
1091 status = spi_readl(as, SR);
1092 pending = status & imr;
1094 if (pending & SPI_BIT(OVRES)) {
1096 spi_writel(as, IDR, SPI_BIT(OVRES));
1097 dev_warn(master->dev.parent, "overrun\n");
1100 * When we get an overrun, we disregard the current
1101 * transfer. Data will not be copied back from any
1102 * bounce buffer and msg->actual_len will not be
1103 * updated with the last xfer.
1105 * We will also not process any remaning transfers in
1108 as->done_status = -EIO;
1111 /* Clear any overrun happening while cleaning up */
1114 complete(&as->xfer_completion);
1116 } else if (pending & (SPI_BIT(RDRF) | SPI_BIT(RXFTHF))) {
1119 if (as->current_remaining_bytes) {
1121 xfer = as->current_transfer;
1122 atmel_spi_pump_pio_data(as, xfer);
1123 if (!as->current_remaining_bytes)
1124 spi_writel(as, IDR, pending);
1126 complete(&as->xfer_completion);
1129 atmel_spi_unlock(as);
1131 WARN_ONCE(pending, "IRQ not handled, pending = %x\n", pending);
1133 spi_writel(as, IDR, pending);
1140 atmel_spi_pdc_interrupt(int irq, void *dev_id)
1142 struct spi_master *master = dev_id;
1143 struct atmel_spi *as = spi_master_get_devdata(master);
1144 u32 status, pending, imr;
1147 imr = spi_readl(as, IMR);
1148 status = spi_readl(as, SR);
1149 pending = status & imr;
1151 if (pending & SPI_BIT(OVRES)) {
1155 spi_writel(as, IDR, (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX)
1158 /* Clear any overrun happening while cleaning up */
1161 as->done_status = -EIO;
1163 complete(&as->xfer_completion);
1165 } else if (pending & (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX))) {
1168 spi_writel(as, IDR, pending);
1170 complete(&as->xfer_completion);
1176 static int atmel_spi_setup(struct spi_device *spi)
1178 struct atmel_spi *as;
1179 struct atmel_spi_device *asd;
1181 unsigned int bits = spi->bits_per_word;
1183 as = spi_master_get_devdata(spi->master);
1185 /* see notes above re chipselect */
1186 if (!atmel_spi_is_v2(as)
1187 && spi->chip_select == 0
1188 && (spi->mode & SPI_CS_HIGH)) {
1189 dev_dbg(&spi->dev, "setup: can't be active-high\n");
1193 csr = SPI_BF(BITS, bits - 8);
1194 if (spi->mode & SPI_CPOL)
1195 csr |= SPI_BIT(CPOL);
1196 if (!(spi->mode & SPI_CPHA))
1197 csr |= SPI_BIT(NCPHA);
1198 if (!as->use_cs_gpios)
1199 csr |= SPI_BIT(CSAAT);
1201 /* DLYBS is mostly irrelevant since we manage chipselect using GPIOs.
1203 csr |= SPI_BF(DLYBS, 0);
1205 /* DLYBCT adds delays between words. This is useful for slow devices
1206 * that need a bit of time to setup the next transfer.
1208 csr |= SPI_BF(DLYBCT,
1209 (as->spi_clk / 1000000 * spi->word_delay_usecs) >> 5);
1211 asd = spi->controller_state;
1213 asd = kzalloc(sizeof(struct atmel_spi_device), GFP_KERNEL);
1218 * If use_cs_gpios is true this means that we have "cs-gpios"
1219 * defined in the device tree node so we should have
1220 * gotten the GPIO lines from the device tree inside the
1221 * SPI core. Warn if this is not the case but continue since
1222 * CS GPIOs are after all optional.
1224 if (as->use_cs_gpios) {
1225 if (!spi->cs_gpiod) {
1227 "host claims to use CS GPIOs but no CS found in DT by the SPI core\n");
1229 asd->npcs_pin = spi->cs_gpiod;
1232 spi->controller_state = asd;
1238 "setup: bpw %u mode 0x%x -> csr%d %08x\n",
1239 bits, spi->mode, spi->chip_select, csr);
1241 if (!atmel_spi_is_v2(as))
1242 spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
1247 static int atmel_spi_one_transfer(struct spi_master *master,
1248 struct spi_message *msg,
1249 struct spi_transfer *xfer)
1251 struct atmel_spi *as;
1252 struct spi_device *spi = msg->spi;
1255 struct atmel_spi_device *asd;
1258 unsigned long dma_timeout;
1260 as = spi_master_get_devdata(master);
1262 if (!(xfer->tx_buf || xfer->rx_buf) && xfer->len) {
1263 dev_dbg(&spi->dev, "missing rx or tx buf\n");
1267 asd = spi->controller_state;
1268 bits = (asd->csr >> 4) & 0xf;
1269 if (bits != xfer->bits_per_word - 8) {
1271 "you can't yet change bits_per_word in transfers\n");
1272 return -ENOPROTOOPT;
1276 * DMA map early, for performance (empties dcache ASAP) and
1277 * better fault reporting.
1279 if ((!msg->is_dma_mapped)
1281 if (atmel_spi_dma_map_xfer(as, xfer) < 0)
1285 atmel_spi_set_xfer_speed(as, msg->spi, xfer);
1287 as->done_status = 0;
1288 as->current_transfer = xfer;
1289 as->current_remaining_bytes = xfer->len;
1290 while (as->current_remaining_bytes) {
1291 reinit_completion(&as->xfer_completion);
1294 atmel_spi_pdc_next_xfer(master, msg, xfer);
1295 } else if (atmel_spi_use_dma(as, xfer)) {
1296 len = as->current_remaining_bytes;
1297 ret = atmel_spi_next_xfer_dma_submit(master,
1301 "unable to use DMA, fallback to PIO\n");
1302 atmel_spi_next_xfer_pio(master, xfer);
1304 as->current_remaining_bytes -= len;
1305 if (as->current_remaining_bytes < 0)
1306 as->current_remaining_bytes = 0;
1309 atmel_spi_next_xfer_pio(master, xfer);
1312 /* interrupts are disabled, so free the lock for schedule */
1313 atmel_spi_unlock(as);
1314 dma_timeout = wait_for_completion_timeout(&as->xfer_completion,
1317 if (WARN_ON(dma_timeout == 0)) {
1318 dev_err(&spi->dev, "spi transfer timeout\n");
1319 as->done_status = -EIO;
1322 if (as->done_status)
1326 if (as->done_status) {
1328 dev_warn(master->dev.parent,
1329 "overrun (%u/%u remaining)\n",
1330 spi_readl(as, TCR), spi_readl(as, RCR));
1333 * Clean up DMA registers and make sure the data
1334 * registers are empty.
1336 spi_writel(as, RNCR, 0);
1337 spi_writel(as, TNCR, 0);
1338 spi_writel(as, RCR, 0);
1339 spi_writel(as, TCR, 0);
1340 for (timeout = 1000; timeout; timeout--)
1341 if (spi_readl(as, SR) & SPI_BIT(TXEMPTY))
1344 dev_warn(master->dev.parent,
1345 "timeout waiting for TXEMPTY");
1346 while (spi_readl(as, SR) & SPI_BIT(RDRF))
1349 /* Clear any overrun happening while cleaning up */
1352 } else if (atmel_spi_use_dma(as, xfer)) {
1353 atmel_spi_stop_dma(master);
1356 if (!msg->is_dma_mapped
1358 atmel_spi_dma_unmap_xfer(master, xfer);
1363 /* only update length if no error */
1364 msg->actual_length += xfer->len;
1367 if (!msg->is_dma_mapped
1369 atmel_spi_dma_unmap_xfer(master, xfer);
1371 if (xfer->delay_usecs)
1372 udelay(xfer->delay_usecs);
1374 if (xfer->cs_change) {
1375 if (list_is_last(&xfer->transfer_list,
1379 as->cs_active = !as->cs_active;
1381 cs_activate(as, msg->spi);
1383 cs_deactivate(as, msg->spi);
1390 static int atmel_spi_transfer_one_message(struct spi_master *master,
1391 struct spi_message *msg)
1393 struct atmel_spi *as;
1394 struct spi_transfer *xfer;
1395 struct spi_device *spi = msg->spi;
1398 as = spi_master_get_devdata(master);
1400 dev_dbg(&spi->dev, "new message %p submitted for %s\n",
1401 msg, dev_name(&spi->dev));
1404 cs_activate(as, spi);
1406 as->cs_active = true;
1407 as->keep_cs = false;
1410 msg->actual_length = 0;
1412 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
1413 trace_spi_transfer_start(msg, xfer);
1415 ret = atmel_spi_one_transfer(master, msg, xfer);
1419 trace_spi_transfer_stop(msg, xfer);
1423 atmel_spi_disable_pdc_transfer(as);
1425 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
1427 " xfer %p: len %u tx %p/%pad rx %p/%pad\n",
1429 xfer->tx_buf, &xfer->tx_dma,
1430 xfer->rx_buf, &xfer->rx_dma);
1435 cs_deactivate(as, msg->spi);
1437 atmel_spi_unlock(as);
1439 msg->status = as->done_status;
1440 spi_finalize_current_message(spi->master);
1445 static void atmel_spi_cleanup(struct spi_device *spi)
1447 struct atmel_spi_device *asd = spi->controller_state;
1452 spi->controller_state = NULL;
1456 static inline unsigned int atmel_get_version(struct atmel_spi *as)
1458 return spi_readl(as, VERSION) & 0x00000fff;
1461 static void atmel_get_caps(struct atmel_spi *as)
1463 unsigned int version;
1465 version = atmel_get_version(as);
1467 as->caps.is_spi2 = version > 0x121;
1468 as->caps.has_wdrbt = version >= 0x210;
1469 as->caps.has_dma_support = version >= 0x212;
1470 as->caps.has_pdc_support = version < 0x212;
1473 static void atmel_spi_init(struct atmel_spi *as)
1475 spi_writel(as, CR, SPI_BIT(SWRST));
1476 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1478 /* It is recommended to enable FIFOs first thing after reset */
1480 spi_writel(as, CR, SPI_BIT(FIFOEN));
1482 if (as->caps.has_wdrbt) {
1483 spi_writel(as, MR, SPI_BIT(WDRBT) | SPI_BIT(MODFDIS)
1486 spi_writel(as, MR, SPI_BIT(MSTR) | SPI_BIT(MODFDIS));
1490 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
1491 spi_writel(as, CR, SPI_BIT(SPIEN));
1494 static int atmel_spi_probe(struct platform_device *pdev)
1496 struct resource *regs;
1500 struct spi_master *master;
1501 struct atmel_spi *as;
1503 /* Select default pin state */
1504 pinctrl_pm_select_default_state(&pdev->dev);
1506 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1510 irq = platform_get_irq(pdev, 0);
1514 clk = devm_clk_get(&pdev->dev, "spi_clk");
1516 return PTR_ERR(clk);
1518 /* setup spi core then atmel-specific driver state */
1520 master = spi_alloc_master(&pdev->dev, sizeof(*as));
1524 /* the spi->mode bits understood by this driver: */
1525 master->use_gpio_descriptors = true;
1526 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
1527 master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
1528 master->dev.of_node = pdev->dev.of_node;
1529 master->bus_num = pdev->id;
1530 master->num_chipselect = master->dev.of_node ? 0 : 4;
1531 master->setup = atmel_spi_setup;
1532 master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
1533 master->transfer_one_message = atmel_spi_transfer_one_message;
1534 master->cleanup = atmel_spi_cleanup;
1535 master->auto_runtime_pm = true;
1536 master->max_dma_len = SPI_MAX_DMA_XFER;
1537 master->can_dma = atmel_spi_can_dma;
1538 platform_set_drvdata(pdev, master);
1540 as = spi_master_get_devdata(master);
1542 spin_lock_init(&as->lock);
1545 as->regs = devm_ioremap_resource(&pdev->dev, regs);
1546 if (IS_ERR(as->regs)) {
1547 ret = PTR_ERR(as->regs);
1548 goto out_unmap_regs;
1550 as->phybase = regs->start;
1554 init_completion(&as->xfer_completion);
1559 * If there are chip selects in the device tree, those will be
1560 * discovered by the SPI core when registering the SPI master
1561 * and assigned to each SPI device.
1563 as->use_cs_gpios = true;
1564 if (atmel_spi_is_v2(as) &&
1565 pdev->dev.of_node &&
1566 !of_get_property(pdev->dev.of_node, "cs-gpios", NULL)) {
1567 as->use_cs_gpios = false;
1568 master->num_chipselect = 4;
1571 as->use_dma = false;
1572 as->use_pdc = false;
1573 if (as->caps.has_dma_support) {
1574 ret = atmel_spi_configure_dma(master, as);
1577 } else if (ret == -EPROBE_DEFER) {
1580 } else if (as->caps.has_pdc_support) {
1584 if (IS_ENABLED(CONFIG_SOC_SAM_V4_V5)) {
1585 as->addr_rx_bbuf = dma_alloc_coherent(&pdev->dev,
1587 &as->dma_addr_rx_bbuf,
1588 GFP_KERNEL | GFP_DMA);
1589 if (!as->addr_rx_bbuf) {
1590 as->use_dma = false;
1592 as->addr_tx_bbuf = dma_alloc_coherent(&pdev->dev,
1594 &as->dma_addr_tx_bbuf,
1595 GFP_KERNEL | GFP_DMA);
1596 if (!as->addr_tx_bbuf) {
1597 as->use_dma = false;
1598 dma_free_coherent(&pdev->dev, SPI_MAX_DMA_XFER,
1600 as->dma_addr_rx_bbuf);
1604 dev_info(master->dev.parent,
1605 " can not allocate dma coherent memory\n");
1608 if (as->caps.has_dma_support && !as->use_dma)
1609 dev_info(&pdev->dev, "Atmel SPI Controller using PIO only\n");
1612 ret = devm_request_irq(&pdev->dev, irq, atmel_spi_pdc_interrupt,
1613 0, dev_name(&pdev->dev), master);
1615 ret = devm_request_irq(&pdev->dev, irq, atmel_spi_pio_interrupt,
1616 0, dev_name(&pdev->dev), master);
1619 goto out_unmap_regs;
1621 /* Initialize the hardware */
1622 ret = clk_prepare_enable(clk);
1626 as->spi_clk = clk_get_rate(clk);
1629 if (!of_property_read_u32(pdev->dev.of_node, "atmel,fifo-size",
1631 dev_info(&pdev->dev, "Using FIFO (%u data)\n", as->fifo_size);
1636 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT);
1637 pm_runtime_use_autosuspend(&pdev->dev);
1638 pm_runtime_set_active(&pdev->dev);
1639 pm_runtime_enable(&pdev->dev);
1641 ret = devm_spi_register_master(&pdev->dev, master);
1646 dev_info(&pdev->dev, "Atmel SPI Controller version 0x%x at 0x%08lx (irq %d)\n",
1647 atmel_get_version(as), (unsigned long)regs->start,
1653 pm_runtime_disable(&pdev->dev);
1654 pm_runtime_set_suspended(&pdev->dev);
1657 atmel_spi_release_dma(master);
1659 spi_writel(as, CR, SPI_BIT(SWRST));
1660 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1661 clk_disable_unprepare(clk);
1665 spi_master_put(master);
1669 static int atmel_spi_remove(struct platform_device *pdev)
1671 struct spi_master *master = platform_get_drvdata(pdev);
1672 struct atmel_spi *as = spi_master_get_devdata(master);
1674 pm_runtime_get_sync(&pdev->dev);
1676 /* reset the hardware and block queue progress */
1678 atmel_spi_stop_dma(master);
1679 atmel_spi_release_dma(master);
1680 if (IS_ENABLED(CONFIG_SOC_SAM_V4_V5)) {
1681 dma_free_coherent(&pdev->dev, SPI_MAX_DMA_XFER,
1683 as->dma_addr_tx_bbuf);
1684 dma_free_coherent(&pdev->dev, SPI_MAX_DMA_XFER,
1686 as->dma_addr_rx_bbuf);
1690 spin_lock_irq(&as->lock);
1691 spi_writel(as, CR, SPI_BIT(SWRST));
1692 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1694 spin_unlock_irq(&as->lock);
1696 clk_disable_unprepare(as->clk);
1698 pm_runtime_put_noidle(&pdev->dev);
1699 pm_runtime_disable(&pdev->dev);
1705 static int atmel_spi_runtime_suspend(struct device *dev)
1707 struct spi_master *master = dev_get_drvdata(dev);
1708 struct atmel_spi *as = spi_master_get_devdata(master);
1710 clk_disable_unprepare(as->clk);
1711 pinctrl_pm_select_sleep_state(dev);
1716 static int atmel_spi_runtime_resume(struct device *dev)
1718 struct spi_master *master = dev_get_drvdata(dev);
1719 struct atmel_spi *as = spi_master_get_devdata(master);
1721 pinctrl_pm_select_default_state(dev);
1723 return clk_prepare_enable(as->clk);
1726 #ifdef CONFIG_PM_SLEEP
1727 static int atmel_spi_suspend(struct device *dev)
1729 struct spi_master *master = dev_get_drvdata(dev);
1732 /* Stop the queue running */
1733 ret = spi_master_suspend(master);
1737 if (!pm_runtime_suspended(dev))
1738 atmel_spi_runtime_suspend(dev);
1743 static int atmel_spi_resume(struct device *dev)
1745 struct spi_master *master = dev_get_drvdata(dev);
1746 struct atmel_spi *as = spi_master_get_devdata(master);
1749 ret = clk_prepare_enable(as->clk);
1755 clk_disable_unprepare(as->clk);
1757 if (!pm_runtime_suspended(dev)) {
1758 ret = atmel_spi_runtime_resume(dev);
1763 /* Start the queue running */
1764 return spi_master_resume(master);
1768 static const struct dev_pm_ops atmel_spi_pm_ops = {
1769 SET_SYSTEM_SLEEP_PM_OPS(atmel_spi_suspend, atmel_spi_resume)
1770 SET_RUNTIME_PM_OPS(atmel_spi_runtime_suspend,
1771 atmel_spi_runtime_resume, NULL)
1773 #define ATMEL_SPI_PM_OPS (&atmel_spi_pm_ops)
1775 #define ATMEL_SPI_PM_OPS NULL
1778 #if defined(CONFIG_OF)
1779 static const struct of_device_id atmel_spi_dt_ids[] = {
1780 { .compatible = "atmel,at91rm9200-spi" },
1784 MODULE_DEVICE_TABLE(of, atmel_spi_dt_ids);
1787 static struct platform_driver atmel_spi_driver = {
1789 .name = "atmel_spi",
1790 .pm = ATMEL_SPI_PM_OPS,
1791 .of_match_table = of_match_ptr(atmel_spi_dt_ids),
1793 .probe = atmel_spi_probe,
1794 .remove = atmel_spi_remove,
1796 module_platform_driver(atmel_spi_driver);
1798 MODULE_DESCRIPTION("Atmel AT32/AT91 SPI Controller driver");
1799 MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
1800 MODULE_LICENSE("GPL");
1801 MODULE_ALIAS("platform:atmel_spi");