1 // SPDX-License-Identifier: GPL-2.0
3 * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
5 * Copyright (C) 1997 Eddie C. Dost (ecd@skynet.be)
6 * Copyright (C) 1998-1999 Pete Zaitcev (zaitcev@yahoo.com)
8 * This is mainly a variation of 8250.c, credits go to authors mentioned
9 * therein. In fact this driver should be merged into the generic 8250.c
10 * infrastructure perhaps using a 8250_sparc.c module.
12 * Fixed to use tty_get_baud_rate().
13 * Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
15 * Converted to new 2.5.x UART layer.
16 * David S. Miller (davem@davemloft.net), 2002-Jul-29
19 #include <linux/module.h>
20 #include <linux/kernel.h>
21 #include <linux/spinlock.h>
22 #include <linux/errno.h>
23 #include <linux/tty.h>
24 #include <linux/tty_flip.h>
25 #include <linux/major.h>
26 #include <linux/string.h>
27 #include <linux/ptrace.h>
28 #include <linux/ioport.h>
29 #include <linux/circ_buf.h>
30 #include <linux/serial.h>
31 #include <linux/sysrq.h>
32 #include <linux/console.h>
33 #include <linux/slab.h>
35 #include <linux/serio.h>
37 #include <linux/serial_reg.h>
38 #include <linux/init.h>
39 #include <linux/delay.h>
40 #include <linux/of_device.h>
45 #include <asm/setup.h>
47 #include <linux/serial_core.h>
48 #include <linux/sunserialcore.h>
50 /* We are on a NS PC87303 clocked with 24.0 MHz, which results
51 * in a UART clock of 1.8462 MHz.
53 #define SU_BASE_BAUD (1846200 / 16)
55 enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
56 static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
58 struct serial_uart_config {
60 int dfl_xmit_fifo_size;
65 * Here we define the default xmit fifo size used for each type of UART.
67 static const struct serial_uart_config uart_config[] = {
72 { "16550A", 16, UART_CLEAR_FIFO | UART_USE_FIFO },
74 { "ST16650", 1, UART_CLEAR_FIFO | UART_STARTECH },
75 { "ST16650V2", 32, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
76 { "TI16750", 64, UART_CLEAR_FIFO | UART_USE_FIFO },
78 { "16C950/954", 128, UART_CLEAR_FIFO | UART_USE_FIFO },
79 { "ST16654", 64, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
80 { "XR16850", 128, UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
81 { "RSA", 2048, UART_CLEAR_FIFO | UART_USE_FIFO }
84 struct uart_sunsu_port {
85 struct uart_port port;
90 unsigned int lsr_break_flag;
93 /* Probing information. */
95 unsigned int type_probed; /* XXX Stupid */
96 unsigned long reg_size;
104 static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
106 offset <<= up->port.regshift;
108 switch (up->port.iotype) {
110 outb(up->port.hub6 - 1 + offset, up->port.iobase);
111 return inb(up->port.iobase + 1);
114 return readb(up->port.membase + offset);
117 return inb(up->port.iobase + offset);
121 static void serial_out(struct uart_sunsu_port *up, int offset, int value)
123 #ifndef CONFIG_SPARC64
125 * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
126 * connected with a gate then go to SlavIO. When IRQ4 goes tristated
127 * gate outputs a logical one. Since we use level triggered interrupts
128 * we have lockup and watchdog reset. We cannot mask IRQ because
129 * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
130 * This problem is similar to what Alpha people suffer, see serial.c.
132 if (offset == UART_MCR)
133 value |= UART_MCR_OUT2;
135 offset <<= up->port.regshift;
137 switch (up->port.iotype) {
139 outb(up->port.hub6 - 1 + offset, up->port.iobase);
140 outb(value, up->port.iobase + 1);
144 writeb(value, up->port.membase + offset);
148 outb(value, up->port.iobase + offset);
153 * We used to support using pause I/O for certain machines. We
154 * haven't supported this for a while, but just in case it's badly
155 * needed for certain old 386 machines, I've left these #define's
158 #define serial_inp(up, offset) serial_in(up, offset)
159 #define serial_outp(up, offset, value) serial_out(up, offset, value)
165 static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
167 serial_out(up, UART_SCR, offset);
168 serial_out(up, UART_ICR, value);
171 #if 0 /* Unused currently */
172 static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
176 serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
177 serial_out(up, UART_SCR, offset);
178 value = serial_in(up, UART_ICR);
179 serial_icr_write(up, UART_ACR, up->acr);
185 #ifdef CONFIG_SERIAL_8250_RSA
187 * Attempts to turn on the RSA FIFO. Returns zero on failure.
188 * We set the port uart clock rate if we succeed.
190 static int __enable_rsa(struct uart_sunsu_port *up)
195 mode = serial_inp(up, UART_RSA_MSR);
196 result = mode & UART_RSA_MSR_FIFO;
199 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
200 mode = serial_inp(up, UART_RSA_MSR);
201 result = mode & UART_RSA_MSR_FIFO;
205 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
210 static void enable_rsa(struct uart_sunsu_port *up)
212 if (up->port.type == PORT_RSA) {
213 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
214 spin_lock_irq(&up->port.lock);
216 spin_unlock_irq(&up->port.lock);
218 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
219 serial_outp(up, UART_RSA_FRR, 0);
224 * Attempts to turn off the RSA FIFO. Returns zero on failure.
225 * It is unknown why interrupts were disabled in here. However,
226 * the caller is expected to preserve this behaviour by grabbing
227 * the spinlock before calling this function.
229 static void disable_rsa(struct uart_sunsu_port *up)
234 if (up->port.type == PORT_RSA &&
235 up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
236 spin_lock_irq(&up->port.lock);
238 mode = serial_inp(up, UART_RSA_MSR);
239 result = !(mode & UART_RSA_MSR_FIFO);
242 serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
243 mode = serial_inp(up, UART_RSA_MSR);
244 result = !(mode & UART_RSA_MSR_FIFO);
248 up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
249 spin_unlock_irq(&up->port.lock);
252 #endif /* CONFIG_SERIAL_8250_RSA */
254 static inline void __stop_tx(struct uart_sunsu_port *p)
256 if (p->ier & UART_IER_THRI) {
257 p->ier &= ~UART_IER_THRI;
258 serial_out(p, UART_IER, p->ier);
262 static void sunsu_stop_tx(struct uart_port *port)
264 struct uart_sunsu_port *up =
265 container_of(port, struct uart_sunsu_port, port);
270 * We really want to stop the transmitter from sending.
272 if (up->port.type == PORT_16C950) {
273 up->acr |= UART_ACR_TXDIS;
274 serial_icr_write(up, UART_ACR, up->acr);
278 static void sunsu_start_tx(struct uart_port *port)
280 struct uart_sunsu_port *up =
281 container_of(port, struct uart_sunsu_port, port);
283 if (!(up->ier & UART_IER_THRI)) {
284 up->ier |= UART_IER_THRI;
285 serial_out(up, UART_IER, up->ier);
289 * Re-enable the transmitter if we disabled it.
291 if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
292 up->acr &= ~UART_ACR_TXDIS;
293 serial_icr_write(up, UART_ACR, up->acr);
297 static void sunsu_stop_rx(struct uart_port *port)
299 struct uart_sunsu_port *up =
300 container_of(port, struct uart_sunsu_port, port);
302 up->ier &= ~UART_IER_RLSI;
303 up->port.read_status_mask &= ~UART_LSR_DR;
304 serial_out(up, UART_IER, up->ier);
307 static void sunsu_enable_ms(struct uart_port *port)
309 struct uart_sunsu_port *up =
310 container_of(port, struct uart_sunsu_port, port);
313 spin_lock_irqsave(&up->port.lock, flags);
314 up->ier |= UART_IER_MSI;
315 serial_out(up, UART_IER, up->ier);
316 spin_unlock_irqrestore(&up->port.lock, flags);
320 receive_chars(struct uart_sunsu_port *up, unsigned char *status)
322 struct tty_port *port = &up->port.state->port;
323 unsigned char ch, flag;
325 int saw_console_brk = 0;
328 ch = serial_inp(up, UART_RX);
330 up->port.icount.rx++;
332 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
333 UART_LSR_FE | UART_LSR_OE))) {
335 * For statistics only
337 if (*status & UART_LSR_BI) {
338 *status &= ~(UART_LSR_FE | UART_LSR_PE);
339 up->port.icount.brk++;
340 if (up->port.cons != NULL &&
341 up->port.line == up->port.cons->index)
344 * We do the SysRQ and SAK checking
345 * here because otherwise the break
346 * may get masked by ignore_status_mask
347 * or read_status_mask.
349 if (uart_handle_break(&up->port))
351 } else if (*status & UART_LSR_PE)
352 up->port.icount.parity++;
353 else if (*status & UART_LSR_FE)
354 up->port.icount.frame++;
355 if (*status & UART_LSR_OE)
356 up->port.icount.overrun++;
359 * Mask off conditions which should be ingored.
361 *status &= up->port.read_status_mask;
363 if (up->port.cons != NULL &&
364 up->port.line == up->port.cons->index) {
365 /* Recover the break flag from console xmit */
366 *status |= up->lsr_break_flag;
367 up->lsr_break_flag = 0;
370 if (*status & UART_LSR_BI) {
372 } else if (*status & UART_LSR_PE)
374 else if (*status & UART_LSR_FE)
377 if (uart_handle_sysrq_char(&up->port, ch))
379 if ((*status & up->port.ignore_status_mask) == 0)
380 tty_insert_flip_char(port, ch, flag);
381 if (*status & UART_LSR_OE)
383 * Overrun is special, since it's reported
384 * immediately, and doesn't affect the current
387 tty_insert_flip_char(port, 0, TTY_OVERRUN);
389 *status = serial_inp(up, UART_LSR);
390 } while ((*status & UART_LSR_DR) && (max_count-- > 0));
396 static void transmit_chars(struct uart_sunsu_port *up)
398 struct circ_buf *xmit = &up->port.state->xmit;
401 if (up->port.x_char) {
402 serial_outp(up, UART_TX, up->port.x_char);
403 up->port.icount.tx++;
407 if (uart_tx_stopped(&up->port)) {
408 sunsu_stop_tx(&up->port);
411 if (uart_circ_empty(xmit)) {
416 count = up->port.fifosize;
418 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
419 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
420 up->port.icount.tx++;
421 if (uart_circ_empty(xmit))
423 } while (--count > 0);
425 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
426 uart_write_wakeup(&up->port);
428 if (uart_circ_empty(xmit))
432 static void check_modem_status(struct uart_sunsu_port *up)
436 status = serial_in(up, UART_MSR);
438 if ((status & UART_MSR_ANY_DELTA) == 0)
441 if (status & UART_MSR_TERI)
442 up->port.icount.rng++;
443 if (status & UART_MSR_DDSR)
444 up->port.icount.dsr++;
445 if (status & UART_MSR_DDCD)
446 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
447 if (status & UART_MSR_DCTS)
448 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
450 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
453 static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
455 struct uart_sunsu_port *up = dev_id;
457 unsigned char status;
459 spin_lock_irqsave(&up->port.lock, flags);
462 status = serial_inp(up, UART_LSR);
463 if (status & UART_LSR_DR)
464 receive_chars(up, &status);
465 check_modem_status(up);
466 if (status & UART_LSR_THRE)
469 spin_unlock_irqrestore(&up->port.lock, flags);
471 tty_flip_buffer_push(&up->port.state->port);
473 spin_lock_irqsave(&up->port.lock, flags);
475 } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
477 spin_unlock_irqrestore(&up->port.lock, flags);
482 /* Separate interrupt handling path for keyboard/mouse ports. */
485 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
486 unsigned int iflag, unsigned int quot);
488 static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
490 unsigned int cur_cflag = up->cflag;
494 up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
496 quot = up->port.uartclk / (16 * new_baud);
498 sunsu_change_speed(&up->port, up->cflag, 0, quot);
501 static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
504 unsigned char ch = serial_inp(up, UART_RX);
506 /* Stop-A is handled by drivers/char/keyboard.c now. */
507 if (up->su_type == SU_PORT_KBD) {
509 serio_interrupt(&up->serio, ch, 0);
511 } else if (up->su_type == SU_PORT_MS) {
512 int ret = suncore_mouse_baud_detection(ch, is_break);
516 sunsu_change_mouse_baud(up);
523 serio_interrupt(&up->serio, ch, 0);
528 } while (serial_in(up, UART_LSR) & UART_LSR_DR);
531 static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
533 struct uart_sunsu_port *up = dev_id;
535 if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
536 unsigned char status = serial_inp(up, UART_LSR);
538 if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
539 receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
545 static unsigned int sunsu_tx_empty(struct uart_port *port)
547 struct uart_sunsu_port *up =
548 container_of(port, struct uart_sunsu_port, port);
552 spin_lock_irqsave(&up->port.lock, flags);
553 ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
554 spin_unlock_irqrestore(&up->port.lock, flags);
559 static unsigned int sunsu_get_mctrl(struct uart_port *port)
561 struct uart_sunsu_port *up =
562 container_of(port, struct uart_sunsu_port, port);
563 unsigned char status;
566 status = serial_in(up, UART_MSR);
569 if (status & UART_MSR_DCD)
571 if (status & UART_MSR_RI)
573 if (status & UART_MSR_DSR)
575 if (status & UART_MSR_CTS)
580 static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
582 struct uart_sunsu_port *up =
583 container_of(port, struct uart_sunsu_port, port);
584 unsigned char mcr = 0;
586 if (mctrl & TIOCM_RTS)
588 if (mctrl & TIOCM_DTR)
590 if (mctrl & TIOCM_OUT1)
591 mcr |= UART_MCR_OUT1;
592 if (mctrl & TIOCM_OUT2)
593 mcr |= UART_MCR_OUT2;
594 if (mctrl & TIOCM_LOOP)
595 mcr |= UART_MCR_LOOP;
597 serial_out(up, UART_MCR, mcr);
600 static void sunsu_break_ctl(struct uart_port *port, int break_state)
602 struct uart_sunsu_port *up =
603 container_of(port, struct uart_sunsu_port, port);
606 spin_lock_irqsave(&up->port.lock, flags);
607 if (break_state == -1)
608 up->lcr |= UART_LCR_SBC;
610 up->lcr &= ~UART_LCR_SBC;
611 serial_out(up, UART_LCR, up->lcr);
612 spin_unlock_irqrestore(&up->port.lock, flags);
615 static int sunsu_startup(struct uart_port *port)
617 struct uart_sunsu_port *up =
618 container_of(port, struct uart_sunsu_port, port);
622 if (up->port.type == PORT_16C950) {
623 /* Wake up and initialize UART */
625 serial_outp(up, UART_LCR, 0xBF);
626 serial_outp(up, UART_EFR, UART_EFR_ECB);
627 serial_outp(up, UART_IER, 0);
628 serial_outp(up, UART_LCR, 0);
629 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
630 serial_outp(up, UART_LCR, 0xBF);
631 serial_outp(up, UART_EFR, UART_EFR_ECB);
632 serial_outp(up, UART_LCR, 0);
635 #ifdef CONFIG_SERIAL_8250_RSA
637 * If this is an RSA port, see if we can kick it up to the
638 * higher speed clock.
644 * Clear the FIFO buffers and disable them.
645 * (they will be reenabled in set_termios())
647 if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
648 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
649 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
650 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
651 serial_outp(up, UART_FCR, 0);
655 * Clear the interrupt registers.
657 (void) serial_inp(up, UART_LSR);
658 (void) serial_inp(up, UART_RX);
659 (void) serial_inp(up, UART_IIR);
660 (void) serial_inp(up, UART_MSR);
663 * At this point, there's no way the LSR could still be 0xff;
664 * if it is, then bail out, because there's likely no UART
667 if (!(up->port.flags & UPF_BUGGY_UART) &&
668 (serial_inp(up, UART_LSR) == 0xff)) {
669 printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
673 if (up->su_type != SU_PORT_PORT) {
674 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
675 IRQF_SHARED, su_typev[up->su_type], up);
677 retval = request_irq(up->port.irq, sunsu_serial_interrupt,
678 IRQF_SHARED, su_typev[up->su_type], up);
681 printk("su: Cannot register IRQ %d\n", up->port.irq);
686 * Now, initialize the UART
688 serial_outp(up, UART_LCR, UART_LCR_WLEN8);
690 spin_lock_irqsave(&up->port.lock, flags);
692 up->port.mctrl |= TIOCM_OUT2;
694 sunsu_set_mctrl(&up->port, up->port.mctrl);
695 spin_unlock_irqrestore(&up->port.lock, flags);
698 * Finally, enable interrupts. Note: Modem status interrupts
699 * are set via set_termios(), which will be occurring imminently
700 * anyway, so we don't enable them here.
702 up->ier = UART_IER_RLSI | UART_IER_RDI;
703 serial_outp(up, UART_IER, up->ier);
705 if (up->port.flags & UPF_FOURPORT) {
708 * Enable interrupts on the AST Fourport board
710 icp = (up->port.iobase & 0xfe0) | 0x01f;
716 * And clear the interrupt registers again for luck.
718 (void) serial_inp(up, UART_LSR);
719 (void) serial_inp(up, UART_RX);
720 (void) serial_inp(up, UART_IIR);
721 (void) serial_inp(up, UART_MSR);
726 static void sunsu_shutdown(struct uart_port *port)
728 struct uart_sunsu_port *up =
729 container_of(port, struct uart_sunsu_port, port);
733 * Disable interrupts from this port
736 serial_outp(up, UART_IER, 0);
738 spin_lock_irqsave(&up->port.lock, flags);
739 if (up->port.flags & UPF_FOURPORT) {
740 /* reset interrupts on the AST Fourport board */
741 inb((up->port.iobase & 0xfe0) | 0x1f);
742 up->port.mctrl |= TIOCM_OUT1;
744 up->port.mctrl &= ~TIOCM_OUT2;
746 sunsu_set_mctrl(&up->port, up->port.mctrl);
747 spin_unlock_irqrestore(&up->port.lock, flags);
750 * Disable break condition and FIFOs
752 serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
753 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
754 UART_FCR_CLEAR_RCVR |
755 UART_FCR_CLEAR_XMIT);
756 serial_outp(up, UART_FCR, 0);
758 #ifdef CONFIG_SERIAL_8250_RSA
760 * Reset the RSA board back to 115kbps compat mode.
766 * Read data port to reset things.
768 (void) serial_in(up, UART_RX);
770 free_irq(up->port.irq, up);
774 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
775 unsigned int iflag, unsigned int quot)
777 struct uart_sunsu_port *up =
778 container_of(port, struct uart_sunsu_port, port);
779 unsigned char cval, fcr = 0;
782 switch (cflag & CSIZE) {
801 cval |= UART_LCR_PARITY;
802 if (!(cflag & PARODD))
803 cval |= UART_LCR_EPAR;
806 cval |= UART_LCR_SPAR;
810 * Work around a bug in the Oxford Semiconductor 952 rev B
811 * chip which causes it to seriously miscalculate baud rates
814 if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
818 if (uart_config[up->port.type].flags & UART_USE_FIFO) {
819 if ((up->port.uartclk / quot) < (2400 * 16))
820 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
821 #ifdef CONFIG_SERIAL_8250_RSA
822 else if (up->port.type == PORT_RSA)
823 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
826 fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
828 if (up->port.type == PORT_16750)
829 fcr |= UART_FCR7_64BYTE;
832 * Ok, we're now changing the port state. Do it with
833 * interrupts disabled.
835 spin_lock_irqsave(&up->port.lock, flags);
838 * Update the per-port timeout.
840 uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
842 up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
844 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
845 if (iflag & (IGNBRK | BRKINT | PARMRK))
846 up->port.read_status_mask |= UART_LSR_BI;
849 * Characteres to ignore
851 up->port.ignore_status_mask = 0;
853 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
854 if (iflag & IGNBRK) {
855 up->port.ignore_status_mask |= UART_LSR_BI;
857 * If we're ignoring parity and break indicators,
858 * ignore overruns too (for real raw support).
861 up->port.ignore_status_mask |= UART_LSR_OE;
865 * ignore all characters if CREAD is not set
867 if ((cflag & CREAD) == 0)
868 up->port.ignore_status_mask |= UART_LSR_DR;
871 * CTS flow control flag and modem status interrupts
873 up->ier &= ~UART_IER_MSI;
874 if (UART_ENABLE_MS(&up->port, cflag))
875 up->ier |= UART_IER_MSI;
877 serial_out(up, UART_IER, up->ier);
879 if (uart_config[up->port.type].flags & UART_STARTECH) {
880 serial_outp(up, UART_LCR, 0xBF);
881 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
883 serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
884 serial_outp(up, UART_DLL, quot & 0xff); /* LS of divisor */
885 serial_outp(up, UART_DLM, quot >> 8); /* MS of divisor */
886 if (up->port.type == PORT_16750)
887 serial_outp(up, UART_FCR, fcr); /* set fcr */
888 serial_outp(up, UART_LCR, cval); /* reset DLAB */
889 up->lcr = cval; /* Save LCR */
890 if (up->port.type != PORT_16750) {
891 if (fcr & UART_FCR_ENABLE_FIFO) {
892 /* emulated UARTs (Lucent Venus 167x) need two steps */
893 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
895 serial_outp(up, UART_FCR, fcr); /* set fcr */
900 spin_unlock_irqrestore(&up->port.lock, flags);
904 sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
905 struct ktermios *old)
907 unsigned int baud, quot;
910 * Ask the core to calculate the divisor for us.
912 baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
913 quot = uart_get_divisor(port, baud);
915 sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
918 static void sunsu_release_port(struct uart_port *port)
922 static int sunsu_request_port(struct uart_port *port)
927 static void sunsu_config_port(struct uart_port *port, int flags)
929 struct uart_sunsu_port *up =
930 container_of(port, struct uart_sunsu_port, port);
932 if (flags & UART_CONFIG_TYPE) {
934 * We are supposed to call autoconfig here, but this requires
935 * splitting all the OBP probing crap from the UART probing.
936 * We'll do it when we kill sunsu.c altogether.
938 port->type = up->type_probed; /* XXX */
943 sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
949 sunsu_type(struct uart_port *port)
951 int type = port->type;
953 if (type >= ARRAY_SIZE(uart_config))
955 return uart_config[type].name;
958 static const struct uart_ops sunsu_pops = {
959 .tx_empty = sunsu_tx_empty,
960 .set_mctrl = sunsu_set_mctrl,
961 .get_mctrl = sunsu_get_mctrl,
962 .stop_tx = sunsu_stop_tx,
963 .start_tx = sunsu_start_tx,
964 .stop_rx = sunsu_stop_rx,
965 .enable_ms = sunsu_enable_ms,
966 .break_ctl = sunsu_break_ctl,
967 .startup = sunsu_startup,
968 .shutdown = sunsu_shutdown,
969 .set_termios = sunsu_set_termios,
971 .release_port = sunsu_release_port,
972 .request_port = sunsu_request_port,
973 .config_port = sunsu_config_port,
974 .verify_port = sunsu_verify_port,
979 static struct uart_sunsu_port sunsu_ports[UART_NR];
980 static int nr_inst; /* Number of already registered ports */
984 static DEFINE_SPINLOCK(sunsu_serio_lock);
986 static int sunsu_serio_write(struct serio *serio, unsigned char ch)
988 struct uart_sunsu_port *up = serio->port_data;
992 spin_lock_irqsave(&sunsu_serio_lock, flags);
995 lsr = serial_in(up, UART_LSR);
996 } while (!(lsr & UART_LSR_THRE));
998 /* Send the character out. */
999 serial_out(up, UART_TX, ch);
1001 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1006 static int sunsu_serio_open(struct serio *serio)
1008 struct uart_sunsu_port *up = serio->port_data;
1009 unsigned long flags;
1012 spin_lock_irqsave(&sunsu_serio_lock, flags);
1013 if (!up->serio_open) {
1018 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1023 static void sunsu_serio_close(struct serio *serio)
1025 struct uart_sunsu_port *up = serio->port_data;
1026 unsigned long flags;
1028 spin_lock_irqsave(&sunsu_serio_lock, flags);
1030 spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1033 #endif /* CONFIG_SERIO */
1035 static void sunsu_autoconfig(struct uart_sunsu_port *up)
1037 unsigned char status1, status2, scratch, scratch2, scratch3;
1038 unsigned char save_lcr, save_mcr;
1039 unsigned long flags;
1041 if (up->su_type == SU_PORT_NONE)
1044 up->type_probed = PORT_UNKNOWN;
1045 up->port.iotype = UPIO_MEM;
1047 spin_lock_irqsave(&up->port.lock, flags);
1049 if (!(up->port.flags & UPF_BUGGY_UART)) {
1051 * Do a simple existence test first; if we fail this, there's
1052 * no point trying anything else.
1054 * 0x80 is used as a nonsense port to prevent against false
1055 * positives due to ISA bus float. The assumption is that
1056 * 0x80 is a non-existent port; which should be safe since
1057 * include/asm/io.h also makes this assumption.
1059 scratch = serial_inp(up, UART_IER);
1060 serial_outp(up, UART_IER, 0);
1064 scratch2 = serial_inp(up, UART_IER);
1065 serial_outp(up, UART_IER, 0x0f);
1069 scratch3 = serial_inp(up, UART_IER);
1070 serial_outp(up, UART_IER, scratch);
1071 if (scratch2 != 0 || scratch3 != 0x0F)
1072 goto out; /* We failed; there's nothing here */
1075 save_mcr = serial_in(up, UART_MCR);
1076 save_lcr = serial_in(up, UART_LCR);
1079 * Check to see if a UART is really there. Certain broken
1080 * internal modems based on the Rockwell chipset fail this
1081 * test, because they apparently don't implement the loopback
1082 * test mode. So this test is skipped on the COM 1 through
1083 * COM 4 ports. This *should* be safe, since no board
1084 * manufacturer would be stupid enough to design a board
1085 * that conflicts with COM 1-4 --- we hope!
1087 if (!(up->port.flags & UPF_SKIP_TEST)) {
1088 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
1089 status1 = serial_inp(up, UART_MSR) & 0xF0;
1090 serial_outp(up, UART_MCR, save_mcr);
1091 if (status1 != 0x90)
1092 goto out; /* We failed loopback test */
1094 serial_outp(up, UART_LCR, 0xBF); /* set up for StarTech test */
1095 serial_outp(up, UART_EFR, 0); /* EFR is the same as FCR */
1096 serial_outp(up, UART_LCR, 0);
1097 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1098 scratch = serial_in(up, UART_IIR) >> 6;
1101 up->port.type = PORT_16450;
1104 up->port.type = PORT_UNKNOWN;
1107 up->port.type = PORT_16550;
1110 up->port.type = PORT_16550A;
1113 if (up->port.type == PORT_16550A) {
1114 /* Check for Startech UART's */
1115 serial_outp(up, UART_LCR, UART_LCR_DLAB);
1116 if (serial_in(up, UART_EFR) == 0) {
1117 up->port.type = PORT_16650;
1119 serial_outp(up, UART_LCR, 0xBF);
1120 if (serial_in(up, UART_EFR) == 0)
1121 up->port.type = PORT_16650V2;
1124 if (up->port.type == PORT_16550A) {
1125 /* Check for TI 16750 */
1126 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
1127 serial_outp(up, UART_FCR,
1128 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1129 scratch = serial_in(up, UART_IIR) >> 5;
1132 * If this is a 16750, and not a cheap UART
1133 * clone, then it should only go into 64 byte
1134 * mode if the UART_FCR7_64BYTE bit was set
1135 * while UART_LCR_DLAB was latched.
1137 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1138 serial_outp(up, UART_LCR, 0);
1139 serial_outp(up, UART_FCR,
1140 UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1141 scratch = serial_in(up, UART_IIR) >> 5;
1143 up->port.type = PORT_16750;
1145 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1147 serial_outp(up, UART_LCR, save_lcr);
1148 if (up->port.type == PORT_16450) {
1149 scratch = serial_in(up, UART_SCR);
1150 serial_outp(up, UART_SCR, 0xa5);
1151 status1 = serial_in(up, UART_SCR);
1152 serial_outp(up, UART_SCR, 0x5a);
1153 status2 = serial_in(up, UART_SCR);
1154 serial_outp(up, UART_SCR, scratch);
1156 if ((status1 != 0xa5) || (status2 != 0x5a))
1157 up->port.type = PORT_8250;
1160 up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
1162 if (up->port.type == PORT_UNKNOWN)
1164 up->type_probed = up->port.type; /* XXX */
1169 #ifdef CONFIG_SERIAL_8250_RSA
1170 if (up->port.type == PORT_RSA)
1171 serial_outp(up, UART_RSA_FRR, 0);
1173 serial_outp(up, UART_MCR, save_mcr);
1174 serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
1175 UART_FCR_CLEAR_RCVR |
1176 UART_FCR_CLEAR_XMIT));
1177 serial_outp(up, UART_FCR, 0);
1178 (void)serial_in(up, UART_RX);
1179 serial_outp(up, UART_IER, 0);
1182 spin_unlock_irqrestore(&up->port.lock, flags);
1185 static struct uart_driver sunsu_reg = {
1186 .owner = THIS_MODULE,
1187 .driver_name = "sunsu",
1192 static int sunsu_kbd_ms_init(struct uart_sunsu_port *up)
1196 struct serio *serio;
1199 if (up->su_type == SU_PORT_KBD) {
1200 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1203 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1206 quot = up->port.uartclk / (16 * baud);
1208 sunsu_autoconfig(up);
1209 if (up->port.type == PORT_UNKNOWN)
1212 printk("%pOF: %s port at %llx, irq %u\n",
1213 up->port.dev->of_node,
1214 (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
1215 (unsigned long long) up->port.mapbase,
1220 serio->port_data = up;
1222 serio->id.type = SERIO_RS232;
1223 if (up->su_type == SU_PORT_KBD) {
1224 serio->id.proto = SERIO_SUNKBD;
1225 strlcpy(serio->name, "sukbd", sizeof(serio->name));
1227 serio->id.proto = SERIO_SUN;
1228 serio->id.extra = 1;
1229 strlcpy(serio->name, "sums", sizeof(serio->name));
1231 strlcpy(serio->phys,
1232 (!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
1233 sizeof(serio->phys));
1235 serio->write = sunsu_serio_write;
1236 serio->open = sunsu_serio_open;
1237 serio->close = sunsu_serio_close;
1238 serio->dev.parent = up->port.dev;
1240 serio_register_port(serio);
1243 sunsu_change_speed(&up->port, up->cflag, 0, quot);
1245 sunsu_startup(&up->port);
1250 * ------------------------------------------------------------
1251 * Serial console driver
1252 * ------------------------------------------------------------
1255 #ifdef CONFIG_SERIAL_SUNSU_CONSOLE
1257 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1260 * Wait for transmitter & holding register to empty
1262 static void wait_for_xmitr(struct uart_sunsu_port *up)
1264 unsigned int status, tmout = 10000;
1266 /* Wait up to 10ms for the character(s) to be sent. */
1268 status = serial_in(up, UART_LSR);
1270 if (status & UART_LSR_BI)
1271 up->lsr_break_flag = UART_LSR_BI;
1276 } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1278 /* Wait up to 1s for flow control if necessary */
1279 if (up->port.flags & UPF_CONS_FLOW) {
1282 ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1287 static void sunsu_console_putchar(struct uart_port *port, int ch)
1289 struct uart_sunsu_port *up =
1290 container_of(port, struct uart_sunsu_port, port);
1293 serial_out(up, UART_TX, ch);
1297 * Print a string to the serial port trying not to disturb
1298 * any possible real use of the port...
1300 static void sunsu_console_write(struct console *co, const char *s,
1303 struct uart_sunsu_port *up = &sunsu_ports[co->index];
1304 unsigned long flags;
1308 if (up->port.sysrq || oops_in_progress)
1309 locked = spin_trylock_irqsave(&up->port.lock, flags);
1311 spin_lock_irqsave(&up->port.lock, flags);
1314 * First save the UER then disable the interrupts
1316 ier = serial_in(up, UART_IER);
1317 serial_out(up, UART_IER, 0);
1319 uart_console_write(&up->port, s, count, sunsu_console_putchar);
1322 * Finally, wait for transmitter to become empty
1323 * and restore the IER
1326 serial_out(up, UART_IER, ier);
1329 spin_unlock_irqrestore(&up->port.lock, flags);
1333 * Setup initial baud/bits/parity. We do two things here:
1334 * - construct a cflag setting for the first su_open()
1335 * - initialize the serial port
1336 * Return non-zero if we didn't find a serial port.
1338 static int __init sunsu_console_setup(struct console *co, char *options)
1340 static struct ktermios dummy;
1341 struct ktermios termios;
1342 struct uart_port *port;
1344 printk("Console: ttyS%d (SU)\n",
1345 (sunsu_reg.minor - 64) + co->index);
1347 if (co->index > nr_inst)
1349 port = &sunsu_ports[co->index].port;
1354 spin_lock_init(&port->lock);
1356 /* Get firmware console settings. */
1357 sunserial_console_termios(co, port->dev->of_node);
1359 memset(&termios, 0, sizeof(struct ktermios));
1360 termios.c_cflag = co->cflag;
1361 port->mctrl |= TIOCM_DTR;
1362 port->ops->set_termios(port, &termios, &dummy);
1367 static struct console sunsu_console = {
1369 .write = sunsu_console_write,
1370 .device = uart_console_device,
1371 .setup = sunsu_console_setup,
1372 .flags = CON_PRINTBUFFER,
1381 static inline struct console *SUNSU_CONSOLE(void)
1383 return &sunsu_console;
1386 #define SUNSU_CONSOLE() (NULL)
1387 #define sunsu_serial_console_init() do { } while (0)
1390 static enum su_type su_get_type(struct device_node *dp)
1392 struct device_node *ap = of_find_node_by_path("/aliases");
1393 enum su_type rc = SU_PORT_PORT;
1396 const char *keyb = of_get_property(ap, "keyboard", NULL);
1397 const char *ms = of_get_property(ap, "mouse", NULL);
1398 struct device_node *match;
1401 match = of_find_node_by_path(keyb);
1404 * The pointer is used as an identifier not
1405 * as a pointer, we can drop the refcount on
1406 * the of__node immediately after getting it.
1416 match = of_find_node_by_path(ms);
1432 static int su_probe(struct platform_device *op)
1434 struct device_node *dp = op->dev.of_node;
1435 struct uart_sunsu_port *up;
1436 struct resource *rp;
1441 type = su_get_type(dp);
1442 if (type == SU_PORT_PORT) {
1443 if (nr_inst >= UART_NR)
1445 up = &sunsu_ports[nr_inst];
1447 up = kzalloc(sizeof(*up), GFP_KERNEL);
1452 up->port.line = nr_inst;
1454 spin_lock_init(&up->port.lock);
1458 rp = &op->resource[0];
1459 up->port.mapbase = rp->start;
1460 up->reg_size = resource_size(rp);
1461 up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
1462 if (!up->port.membase) {
1463 if (type != SU_PORT_PORT)
1468 up->port.irq = op->archdata.irqs[0];
1470 up->port.dev = &op->dev;
1472 up->port.type = PORT_UNKNOWN;
1473 up->port.uartclk = (SU_BASE_BAUD * 16);
1474 up->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SUNSU_CONSOLE);
1477 if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
1478 err = sunsu_kbd_ms_init(up);
1480 of_iounmap(&op->resource[0],
1481 up->port.membase, up->reg_size);
1485 platform_set_drvdata(op, up);
1492 up->port.flags |= UPF_BOOT_AUTOCONF;
1494 sunsu_autoconfig(up);
1497 if (up->port.type == PORT_UNKNOWN)
1500 up->port.ops = &sunsu_pops;
1502 ignore_line = false;
1503 if (of_node_name_eq(dp, "rsc-console") ||
1504 of_node_name_eq(dp, "lom-console"))
1507 sunserial_console_match(SUNSU_CONSOLE(), dp,
1508 &sunsu_reg, up->port.line,
1510 err = uart_add_one_port(&sunsu_reg, &up->port);
1514 platform_set_drvdata(op, up);
1521 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1526 static int su_remove(struct platform_device *op)
1528 struct uart_sunsu_port *up = platform_get_drvdata(op);
1531 if (up->su_type == SU_PORT_MS ||
1532 up->su_type == SU_PORT_KBD)
1537 serio_unregister_port(&up->serio);
1539 } else if (up->port.type != PORT_UNKNOWN)
1540 uart_remove_one_port(&sunsu_reg, &up->port);
1542 if (up->port.membase)
1543 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1551 static const struct of_device_id su_match[] = {
1568 MODULE_DEVICE_TABLE(of, su_match);
1570 static struct platform_driver su_driver = {
1573 .of_match_table = su_match,
1576 .remove = su_remove,
1579 static int __init sunsu_init(void)
1581 struct device_node *dp;
1585 for_each_node_by_name(dp, "su") {
1586 if (su_get_type(dp) == SU_PORT_PORT)
1589 for_each_node_by_name(dp, "su_pnp") {
1590 if (su_get_type(dp) == SU_PORT_PORT)
1593 for_each_node_by_name(dp, "serial") {
1594 if (of_device_is_compatible(dp, "su")) {
1595 if (su_get_type(dp) == SU_PORT_PORT)
1599 for_each_node_by_type(dp, "serial") {
1600 if (of_device_is_compatible(dp, "su")) {
1601 if (su_get_type(dp) == SU_PORT_PORT)
1607 err = sunserial_register_minors(&sunsu_reg, num_uart);
1612 err = platform_driver_register(&su_driver);
1613 if (err && num_uart)
1614 sunserial_unregister_minors(&sunsu_reg, num_uart);
1619 static void __exit sunsu_exit(void)
1621 platform_driver_unregister(&su_driver);
1623 sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
1626 module_init(sunsu_init);
1627 module_exit(sunsu_exit);
1629 MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
1630 MODULE_DESCRIPTION("Sun SU serial port driver");
1631 MODULE_VERSION("2.0");
1632 MODULE_LICENSE("GPL");