arm64: dts: meson-g12a: Add PCIe node

This adds the Amlogic G12A PCI Express controller node, also
using the USB3+PCIe Combo PHY.

The PHY mode selection is static, thus the USB3+PCIe Combo PHY
phandle would need to be removed from the USB control node if the
shared differential lines are used for PCIe instead of USB3.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 0f6ec1704343f1b67c539c3d7a196c7c623fd823..f76773cabdb1a4f9c00ad3058cbf108084b5d67a 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -60,6 +60,39 @@ soc {
                #size-cells = <2>;
                ranges;
 
+               pcie: pcie@fc000000 {
+                       compatible = "amlogic,g12a-pcie", "snps,dw-pcie";
+                       reg = <0x0 0xfc000000 0x0 0x400000
+                              0x0 0xff648000 0x0 0x2000
+                              0x0 0xfc400000 0x0 0x200000>;
+                       reg-names = "elbi", "cfg", "config";
+                       interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+                       #interrupt-cells = <1>;
+                       interrupt-map-mask = <0 0 0 0>;
+                       interrupt-map = <0 0 0 0 &gic GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+                       bus-range = <0x0 0xff>;
+                       #address-cells = <3>;
+                       #size-cells = <2>;
+                       device_type = "pci";
+                       ranges = <0x81000000 0 0 0x0 0xfc600000 0 0x00100000
+                                 0x82000000 0 0xfc700000 0x0 0xfc700000 0 0x1900000>;
+
+                       clocks = <&clkc CLKID_PCIE_PHY
+                                 &clkc CLKID_PCIE_COMB
+                                 &clkc CLKID_PCIE_PLL>;
+                       clock-names = "general",
+                                     "pclk",
+                                     "port";
+                       resets = <&reset RESET_PCIE_CTRL_A>,
+                                <&reset RESET_PCIE_APB>;
+                       reset-names = "port",
+                                     "apb";
+                       num-lanes = <1>;
+                       phys = <&usb3_pcie_phy PHY_TYPE_PCIE>;
+                       phy-names = "pcie";
+                       status = "disabled";
+               };
+
                ethmac: ethernet@ff3f0000 {
                        compatible = "amlogic,meson-axg-dwmac",
                                     "snps,dwmac-3.70a",

diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
index 6152e928aef2f8a867319b8d51d6294a6b74ebb3..1fdc5af5ae23380c89083ef11e0baceb741c73d8 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -139,6 +139,10 @@ &gpio_intc {
                     "amlogic,meson-gpio-intc";
 };
 
+&pcie {
+       power-domains = <&pwrc PWRC_SM1_PCIE_ID>;
+};
+
 &pwrc {
        compatible = "amlogic,meson-sm1-pwrc";
 };