This commit adds the touchscreen from Toradex so one can enable it.
It is disabled by default because the pins are also used for PWM<B>,
PWM<C>, aka pwm2, pwm3 which is the standard use for colibri boards.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
&i2c3 {
status = "okay";
+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcap_1>;
+ reg = <0x4a>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
+ reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; /* SODIMM 30 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
};
};
+&iomuxc {
+ pinctrl_pcap_1: pcap1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* SODIMM 28 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SODIMM 30 */
+ >;
+ };
+
+ pinctrl_mxt_ts: mxttsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x130b0 /* SODIMM 107 */
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x130b0 /* SODIMM 106 */
+ >;
+ };
+};
+
&ipu1_di0_disp0 {
remote-endpoint = <&lcd_display_in>;
};
&i2c1 {
status = "okay";
+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
pcie-switch@58 {
compatible = "plx,pex8605";
reg = <0x58>;
&i2c1 {
status = "okay";
+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
&i2c1 {
status = "okay";
+ /*
+ * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
+ * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
+ */
+ touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ reg = <0x4a>;
+ interrupt-parent = <&gpio6>;
+ interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* SODIMM 13 */
+ status = "disabled";
+ };
+
eeprom@50 {
compatible = "atmel,24c02";
reg = <0x50>;