# Makefile for the PowerPC 8xx linux kernel.
#
obj-y += m8xx_setup.o machine_check.o pic.o
+obj-$(CONFIG_CPM1) += cpm1.o
+obj-$(CONFIG_UCODE_PATCH) += micropatch.o
obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
obj-$(CONFIG_MPC86XADS) += mpc86xads_setup.o
obj-$(CONFIG_PPC_EP88XC) += ep88xc.o
{
int cpm_vec;
- /* Get the vector by setting the ACK bit and then reading
+ /*
+ * Get the vector by setting the ACK bit and then reading
* the register.
*/
out_be16(&cpic_reg->cpic_civr, 1);
return 0;
}
-/* The CPM can generate the error interrupt when there is a race condition
+/*
+ * The CPM can generate the error interrupt when there is a race condition
* between generating and masking interrupts. All we have to do is ACK it
* and return. This is a no-op function so we don't need any special
* tests in the interrupt handler.
cpmp = &mpc8xx_immr->im_cpm;
#ifndef CONFIG_PPC_EARLY_DEBUG_CPM
- /* Perform a reset.
- */
+ /* Perform a reset. */
out_be16(&cpmp->cp_cpcr, CPM_CR_RST | CPM_CR_FLG);
- /* Wait for it.
- */
+ /* Wait for it. */
while (in_be16(&cpmp->cp_cpcr) & CPM_CR_FLG);
#endif
cpm_load_patch(cpmp);
#endif
- /* Set SDMA Bus Request priority 5.
+ /*
+ * Set SDMA Bus Request priority 5.
* On 860T, this also enables FEC priority 6. I am not sure
* this is what we really want for some applications, but the
* manual recommends it.
}
EXPORT_SYMBOL(cpm_command);
-/* Set a baud rate generator. This needs lots of work. There are
+/*
+ * Set a baud rate generator. This needs lots of work. There are
* four BRGs, any of which can be wired to any channel.
* The internal baud rate clock is the system clock divided by 16.
* This assumes the baudrate is 16x oversampled by the uart.
{
u32 __iomem *bp;
- /* This is good enough to get SMCs running.....
- */
+ /* This is good enough to get SMCs running..... */
bp = &cpmp->cp_brgc1;
bp += brg;
- /* The BRG has a 12-bit counter. For really slow baud rates (or
+ /*
+ * The BRG has a 12-bit counter. For really slow baud rates (or
* really fast processors), we may have to further divide by 16.
*/
if (((BRG_UART_CLK / rate) - 1) < 4096)
// SPDX-License-Identifier: GPL-2.0
-/* Microcode patches for the CPM as supplied by Motorola.
+/*
+ * Microcode patches for the CPM as supplied by Motorola.
* This is the one for IIC/SPI. There is a newer one that
* also relocates SMC2, but this would require additional changes
* to uart.c, so I am holding off on that for a moment.
obj-$(CONFIG_OF_RTC) += of_rtc.o
obj-$(CONFIG_CPM) += cpm_common.o
-obj-$(CONFIG_CPM1) += cpm1.o
obj-$(CONFIG_CPM2) += cpm2.o cpm2_pic.o cpm_gpio.o
obj-$(CONFIG_8xx_GPIO) += cpm_gpio.o
obj-$(CONFIG_QUICC_ENGINE) += cpm_common.o
obj-$(CONFIG_PPC_DCR) += dcr.o
-obj-$(CONFIG_UCODE_PATCH) += micropatch.o
obj-$(CONFIG_PPC_MPC512x) += mpc5xxx_clocks.o
obj-$(CONFIG_PPC_MPC52xx) += mpc5xxx_clocks.o