Required properties:
- compatible: should be one of the following:
- "socionext,uniphier-sld3-reset" - for PH1-sLD3 SoC.
- "socionext,uniphier-ld4-reset" - for PH1-LD4 SoC.
- "socionext,uniphier-pro4-reset" - for PH1-Pro4 SoC.
- "socionext,uniphier-sld8-reset" - for PH1-sLD8 SoC.
- "socionext,uniphier-pro5-reset" - for PH1-Pro5 SoC.
- "socionext,uniphier-pxs2-reset" - for ProXstream2/PH1-LD6b SoC.
- "socionext,uniphier-ld11-reset" - for PH1-LD11 SoC.
- "socionext,uniphier-ld20-reset" - for PH1-LD20 SoC.
+ "socionext,uniphier-sld3-reset" - for sLD3 SoC.
+ "socionext,uniphier-ld4-reset" - for LD4 SoC.
+ "socionext,uniphier-pro4-reset" - for Pro4 SoC.
+ "socionext,uniphier-sld8-reset" - for sLD8 SoC.
+ "socionext,uniphier-pro5-reset" - for Pro5 SoC.
+ "socionext,uniphier-pxs2-reset" - for PXs2/LD6b SoC.
+ "socionext,uniphier-ld11-reset" - for LD11 SoC.
+ "socionext,uniphier-ld20-reset" - for LD20 SoC.
- #reset-cells: should be 1.
Example:
sysctrl@61840000 {
- compatible = "socionext,uniphier-ld20-sysctrl",
+ compatible = "socionext,uniphier-ld11-sysctrl",
"simple-mfd", "syscon";
reg = <0x61840000 0x4000>;
reset {
- compatible = "socionext,uniphier-ld20-reset";
+ compatible = "socionext,uniphier-ld11-reset";
#reset-cells = <1>;
};
};
-Media I/O (MIO) reset
----------------------
+Media I/O (MIO) reset, SD reset
+-------------------------------
Required properties:
- compatible: should be one of the following:
- "socionext,uniphier-sld3-mio-reset" - for PH1-sLD3 SoC.
- "socionext,uniphier-ld4-mio-reset" - for PH1-LD4 SoC.
- "socionext,uniphier-pro4-mio-reset" - for PH1-Pro4 SoC.
- "socionext,uniphier-sld8-mio-reset" - for PH1-sLD8 SoC.
- "socionext,uniphier-pro5-mio-reset" - for PH1-Pro5 SoC.
- "socionext,uniphier-pxs2-mio-reset" - for ProXstream2/PH1-LD6b SoC.
- "socionext,uniphier-ld11-mio-reset" - for PH1-LD11 SoC.
- "socionext,uniphier-ld20-mio-reset" - for PH1-LD20 SoC.
+ "socionext,uniphier-sld3-mio-reset" - for sLD3 SoC.
+ "socionext,uniphier-ld4-mio-reset" - for LD4 SoC.
+ "socionext,uniphier-pro4-mio-reset" - for Pro4 SoC.
+ "socionext,uniphier-sld8-mio-reset" - for sLD8 SoC.
+ "socionext,uniphier-pro5-sd-reset" - for Pro5 SoC.
+ "socionext,uniphier-pxs2-sd-reset" - for PXs2/LD6b SoC.
+ "socionext,uniphier-ld11-mio-reset" - for LD11 SoC.
+ "socionext,uniphier-ld20-sd-reset" - for LD20 SoC.
- #reset-cells: should be 1.
Example:
mioctrl@59810000 {
- compatible = "socionext,uniphier-ld20-mioctrl",
+ compatible = "socionext,uniphier-ld11-mioctrl",
"simple-mfd", "syscon";
reg = <0x59810000 0x800>;
reset {
- compatible = "socionext,uniphier-ld20-mio-reset";
+ compatible = "socionext,uniphier-ld11-mio-reset";
#reset-cells = <1>;
};
Required properties:
- compatible: should be one of the following:
- "socionext,uniphier-ld4-peri-reset" - for PH1-LD4 SoC.
- "socionext,uniphier-pro4-peri-reset" - for PH1-Pro4 SoC.
- "socionext,uniphier-sld8-peri-reset" - for PH1-sLD8 SoC.
- "socionext,uniphier-pro5-peri-reset" - for PH1-Pro5 SoC.
- "socionext,uniphier-pxs2-peri-reset" - for ProXstream2/PH1-LD6b SoC.
- "socionext,uniphier-ld11-peri-reset" - for PH1-LD11 SoC.
- "socionext,uniphier-ld20-peri-reset" - for PH1-LD20 SoC.
+ "socionext,uniphier-ld4-peri-reset" - for LD4 SoC.
+ "socionext,uniphier-pro4-peri-reset" - for Pro4 SoC.
+ "socionext,uniphier-sld8-peri-reset" - for sLD8 SoC.
+ "socionext,uniphier-pro5-peri-reset" - for Pro5 SoC.
+ "socionext,uniphier-pxs2-peri-reset" - for PXs2/LD6b SoC.
+ "socionext,uniphier-ld11-peri-reset" - for LD11 SoC.
+ "socionext,uniphier-ld20-peri-reset" - for LD20 SoC.
- #reset-cells: should be 1.
Example:
perictrl@59820000 {
- compatible = "socionext,uniphier-ld20-perictrl",
+ compatible = "socionext,uniphier-ld11-perictrl",
"simple-mfd", "syscon";
reg = <0x59820000 0x200>;
reset {
- compatible = "socionext,uniphier-ld20-peri-reset";
+ compatible = "socionext,uniphier-ld11-peri-reset";
#reset-cells = <1>;
};
Binding for Cadence UART Controller
Required properties:
-- compatible : should be "cdns,uart-r1p8", or "xlnx,xuartps"
+- compatible :
+ Use "xlnx,xuartps","cdns,uart-r1p8" for Zynq-7xxx SoC.
+ Use "xlnx,zynqmp-uart","cdns,uart-r1p12" for Zynq Ultrascale+ MPSoC.
- reg: Should contain UART controller registers location and length.
- interrupts: Should contain UART controller interrupts.
- clocks: Must contain phandles to the UART clocks
- "renesas,scifb-r8a73a4" for R8A73A4 (R-Mobile APE6) SCIFB compatible UART.
- "renesas,scifa-r8a7740" for R8A7740 (R-Mobile A1) SCIFA compatible UART.
- "renesas,scifb-r8a7740" for R8A7740 (R-Mobile A1) SCIFB compatible UART.
+ - "renesas,scif-r8a7743" for R8A7743 (RZ/G1M) SCIF compatible UART.
+ - "renesas,scifa-r8a7743" for R8A7743 (RZ/G1M) SCIFA compatible UART.
+ - "renesas,scifb-r8a7743" for R8A7743 (RZ/G1M) SCIFB compatible UART.
+ - "renesas,hscif-r8a7743" for R8A7743 (RZ/G1M) HSCIF compatible UART.
+ - "renesas,scif-r8a7745" for R8A7745 (RZ/G1E) SCIF compatible UART.
+ - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART.
+ - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART.
+ - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART.
- "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART.
- "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART.
- "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART.
- g-use-dma: enable dma usage in gadget driver.
- g-rx-fifo-size: size of rx fifo size in gadget mode.
- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
-
-Deprecated properties:
-- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0)
- in gadget mode.
+- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
Example:
F: arch/arm/configs/mvebu_*_defconfig
ARM/Marvell Berlin SoC support
+M: Jisheng Zhang <jszhang@marvell.com>
M: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
S: Maintained
F: scripts/get_maintainer.pl
+GENWQE (IBM Generic Workqueue Card)
+M: Frank Haverkamp <haver@linux.vnet.ibm.com>
+M: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
+S: Supported
+F: drivers/misc/genwqe/
+
GFS2 FILE SYSTEM
M: Steven Whitehouse <swhiteho@redhat.com>
M: Bob Peterson <rpeterso@redhat.com>
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ cap-sd-highspeed;
cap-mmc-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ /* All direction control is used */
+ st,sig-dir-cmd;
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-pin-fbclk;
+ full-pwr-cycle;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi0_default_mode>;
pinctrl-1 = <&sdi0_sleep_mode>;
- cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218
+ /* GPIO218 MMC_CD */
+ cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;
status = "okay";
};
/* VMMCI level-shifter enable */
snowball_cfg3 {
pins = "GPIO217_AH12";
- ste,config = <&gpio_out_lo>;
+ ste,config = <&gpio_out_hi>;
};
/* VMMCI level-shifter voltage select */
snowball_cfg4 {
};
&mio_clk {
- compatible = "socionext,uniphier-pro5-mio-clock";
+ compatible = "socionext,uniphier-pro5-sd-clock";
};
&mio_rst {
- compatible = "socionext,uniphier-pro5-mio-reset";
+ compatible = "socionext,uniphier-pro5-sd-reset";
};
&peri_clk {
};
&mio_clk {
- compatible = "socionext,uniphier-pxs2-mio-clock";
+ compatible = "socionext,uniphier-pxs2-sd-clock";
};
&mio_rst {
- compatible = "socionext,uniphier-pxs2-mio-reset";
+ compatible = "socionext,uniphier-pxs2-sd-reset";
};
&peri_clk {
global_timer: timer@40002200 {
compatible = "arm,cortex-a9-global-timer";
reg = <0x40002200 0x20>;
- interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&intc>;
clocks = <&clks VF610_CLK_PLATFORM_BUS>;
};
CONFIG_PWM_TEGRA=y
CONFIG_PWM_VT8500=y
CONFIG_PHY_HIX5HD2_SATA=y
+CONFIG_E1000E=y
CONFIG_PWM_STI=y
CONFIG_PWM_BCM2835=y
CONFIG_PWM_BRCMSTB=m
static int imx_gpc_genpd_init(struct device *dev, struct regulator *pu_reg)
{
struct clk *clk;
- int i;
+ int i, ret;
imx6q_pu_domain.reg = pu_reg;
if (!IS_ENABLED(CONFIG_PM_GENERIC_DOMAINS))
return 0;
- pm_genpd_init(&imx6q_pu_domain.base, NULL, false);
- return of_genpd_add_provider_onecell(dev->of_node,
+ for (i = 0; i < ARRAY_SIZE(imx_gpc_domains); i++)
+ pm_genpd_init(imx_gpc_domains[i], NULL, false);
+
+ ret = of_genpd_add_provider_onecell(dev->of_node,
&imx_gpc_onecell_data);
+ if (ret)
+ goto power_off;
+
+ return 0;
+power_off:
+ imx6q_pm_pu_power_off(&imx6q_pu_domain.base);
clk_err:
while (i--)
clk_put(imx6q_pu_domain.clk[i]);
+ imx6q_pu_domain.reg = NULL;
return -EINVAL;
}
ksz9021rn_phy_fixup);
phy_register_fixup_for_uid(PHY_ID_KSZ9031, MICREL_PHY_ID_MASK,
ksz9031rn_phy_fixup);
- phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
+ phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffef,
ar8031_phy_fixup);
phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
ar8035_phy_fixup);
select CACHE_L2X0
select ARM_CPU_SUSPEND
select MACH_MVEBU_ANY
+ select MVEBU_CLK_COREDIV
config MACH_ARMADA_370
bool "Marvell Armada 370 boards"
select CPU_PJ4B
select MACH_MVEBU_V7
select PINCTRL_ARMADA_370
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 370 SoC with device tree.
select HAVE_SMP
select MACH_MVEBU_V7
select PINCTRL_ARMADA_375
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 375 SoC with device tree.
select HAVE_SMP
select MACH_MVEBU_V7
select PINCTRL_ARMADA_38X
- select MVEBU_CLK_COREDIV
help
Say 'Y' here if you want your kernel to support boards based
on the Marvell Armada 380/385 SoC with device tree.
config ARCH_UNIPHIER
bool "Socionext UniPhier SoCs"
depends on ARCH_MULTI_V7
+ select ARCH_HAS_RESET_CONTROLLER
select ARM_AMBA
select ARM_GLOBAL_TIMER
select ARM_GIC
config ARCH_UNIPHIER
bool "Socionext UniPhier SoC Family"
+ select ARCH_HAS_RESET_CONTROLLER
select PINCTRL
help
This enables support for Socionext UniPhier SoC family.
nand-ecc-mode = "hw";
nand-ecc-strength = <8>;
nand-ecc-step-size = <512>;
+ nand-bus-width = <16>;
+ brcm,nand-oob-sector-size = <16>;
#address-cells = <1>;
#size-cells = <1>;
};
<1 14 0xf08>, /* Physical Non-Secure PPI */
<1 11 0xf08>, /* Virtual PPI */
<1 10 0xf08>; /* Hypervisor PPI */
+ fsl,erratum-a008585;
};
pmu {
<1 14 4>, /* Physical Non-Secure PPI, active-low */
<1 11 4>, /* Virtual PPI, active-low */
<1 10 4>; /* Hypervisor PPI, active-low */
+ fsl,erratum-a008585;
};
pmu {
#address-cells = <0x1>;
#size-cells = <0x0>;
cell-index = <1>;
- clocks = <&cpm_syscon0 0 3>;
+ clocks = <&cpm_syscon0 1 21>;
status = "disabled";
};
cap-mmc-highspeed;
clock-frequency = <150000000>;
disable-wp;
- keep-power-in-suspend;
non-removable;
num-slots = <1>;
vmmc-supply = <&vcc_io>;
};
vcc_sd: SWITCH_REG1 {
- regulator-always-on;
- regulator-boot-on;
regulator-name = "vcc_sd";
};
gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
vin-supply = <&vcc_io>;
};
bus-width = <8>;
cap-mmc-highspeed;
disable-wp;
- keep-power-in-suspend;
mmc-pwrseq = <&emmc_pwrseq>;
mmc-hs200-1_2v;
mmc-hs200-1_8v;
clock-freq-min-max = <400000 50000000>;
cap-sd-highspeed;
card-detect-delay = <200>;
- keep-power-in-suspend;
num-slots = <1>;
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
reg = <0x59801000 0x400>;
};
- mioctrl@59810000 {
- compatible = "socionext,uniphier-mioctrl",
+ sdctrl@59810000 {
+ compatible = "socionext,uniphier-ld20-sdctrl",
"simple-mfd", "syscon";
reg = <0x59810000 0x800>;
- mio_clk: clock {
- compatible = "socionext,uniphier-ld20-mio-clock";
+ sd_clk: clock {
+ compatible = "socionext,uniphier-ld20-sd-clock";
#clock-cells = <1>;
};
- mio_rst: reset {
- compatible = "socionext,uniphier-ld20-mio-reset";
+ sd_rst: reset {
+ compatible = "socionext,uniphier-ld20-sd-reset";
#reset-cells = <1>;
};
};
static struct binder_ref *binder_get_ref(struct binder_proc *proc,
- uint32_t desc)
+ u32 desc, bool need_strong_ref)
{
struct rb_node *n = proc->refs_by_desc.rb_node;
struct binder_ref *ref;
while (n) {
ref = rb_entry(n, struct binder_ref, rb_node_desc);
- if (desc < ref->desc)
+ if (desc < ref->desc) {
n = n->rb_left;
- else if (desc > ref->desc)
+ } else if (desc > ref->desc) {
n = n->rb_right;
- else
+ } else if (need_strong_ref && !ref->strong) {
+ binder_user_error("tried to use weak ref as strong ref\n");
+ return NULL;
+ } else {
return ref;
+ }
}
return NULL;
}
} break;
case BINDER_TYPE_HANDLE:
case BINDER_TYPE_WEAK_HANDLE: {
- struct binder_ref *ref = binder_get_ref(proc, fp->handle);
+ struct binder_ref *ref;
+
+ ref = binder_get_ref(proc, fp->handle,
+ fp->type == BINDER_TYPE_HANDLE);
if (ref == NULL) {
pr_err("transaction release %d bad handle %d\n",
if (tr->target.handle) {
struct binder_ref *ref;
- ref = binder_get_ref(proc, tr->target.handle);
+ ref = binder_get_ref(proc, tr->target.handle, true);
if (ref == NULL) {
binder_user_error("%d:%d got transaction to invalid handle\n",
proc->pid, thread->pid);
fp->type = BINDER_TYPE_HANDLE;
else
fp->type = BINDER_TYPE_WEAK_HANDLE;
+ fp->binder = 0;
fp->handle = ref->desc;
+ fp->cookie = 0;
binder_inc_ref(ref, fp->type == BINDER_TYPE_HANDLE,
&thread->todo);
} break;
case BINDER_TYPE_HANDLE:
case BINDER_TYPE_WEAK_HANDLE: {
- struct binder_ref *ref = binder_get_ref(proc, fp->handle);
+ struct binder_ref *ref;
+
+ ref = binder_get_ref(proc, fp->handle,
+ fp->type == BINDER_TYPE_HANDLE);
if (ref == NULL) {
binder_user_error("%d:%d got transaction with invalid handle, %d\n",
return_error = BR_FAILED_REPLY;
goto err_binder_get_ref_for_node_failed;
}
+ fp->binder = 0;
fp->handle = new_ref->desc;
+ fp->cookie = 0;
binder_inc_ref(new_ref, fp->type == BINDER_TYPE_HANDLE, NULL);
trace_binder_transaction_ref_to_ref(t, ref,
new_ref);
binder_debug(BINDER_DEBUG_TRANSACTION,
" fd %d -> %d\n", fp->handle, target_fd);
/* TODO: fput? */
+ fp->binder = 0;
fp->handle = target_fd;
} break;
ref->desc);
}
} else
- ref = binder_get_ref(proc, target);
+ ref = binder_get_ref(proc, target,
+ cmd == BC_ACQUIRE ||
+ cmd == BC_RELEASE);
if (ref == NULL) {
binder_user_error("%d:%d refcount change on invalid ref %d\n",
proc->pid, thread->pid, target);
if (get_user(cookie, (binder_uintptr_t __user *)ptr))
return -EFAULT;
ptr += sizeof(binder_uintptr_t);
- ref = binder_get_ref(proc, target);
+ ref = binder_get_ref(proc, target, false);
if (ref == NULL) {
binder_user_error("%d:%d %s invalid ref %d\n",
proc->pid, thread->pid,
If you are unsure about this, Say N here.
config DEBUG_TEST_DRIVER_REMOVE
- bool "Test driver remove calls during probe"
+ bool "Test driver remove calls during probe (UNSTABLE)"
depends on DEBUG_KERNEL
help
Say Y here if you want the Driver core to test driver remove functions
by calling probe, remove, probe. This tests the remove path without
having to unbind the driver or unload the driver module.
- If you are unsure about this, say N here.
+ This option is expected to find errors and may render your system
+ unusable. You should say N here unless you are explicitly looking to
+ test this functionality.
config SYS_HYPERVISOR
bool
config QCOM_EBI2
bool "Qualcomm External Bus Interface 2 (EBI2)"
depends on HAS_IOMEM
+ depends on ARCH_QCOM || COMPILE_TEST
help
Say y here to enable support for the Qualcomm External Bus
Interface 2, which can be used to connect things like NAND Flash,
if (ret)
return;
- extcon_set_state(info->edev, EXTCON_USB_HOST, !id);
+ extcon_set_state_sync(info->edev, EXTCON_USB_HOST, !id);
}
static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id)
u8 *hbeat_txf_buf = util_heartbeat.recv_buffer;
struct icmsg_negotiate *negop = NULL;
- vmbus_recvpacket(channel, hbeat_txf_buf,
- PAGE_SIZE, &recvlen, &requestid);
+ while (1) {
+
+ vmbus_recvpacket(channel, hbeat_txf_buf,
+ PAGE_SIZE, &recvlen, &requestid);
+
+ if (!recvlen)
+ break;
- if (recvlen > 0) {
icmsghdrp = (struct icmsg_hdr *)&hbeat_txf_buf[
sizeof(struct vmbuspipe_hdr)];
config TI_ADC081C
tristate "Texas Instruments ADC081C/ADC101C/ADC121C family"
depends on I2C
+ select IIO_BUFFER
+ select IIO_TRIGGERED_BUFFER
help
If you say yes here you get support for Texas Instruments ADC081C,
ADC101C and ADC121C ADC chips.
struct device *dev = &data->client->dev;
int ret;
unsigned int val;
+ __be16 rval;
- ret = regmap_bulk_read(data->regmap, ATLAS_REG_EC_PROBE, &val, 2);
+ ret = regmap_bulk_read(data->regmap, ATLAS_REG_EC_PROBE, &rval, 2);
if (ret)
return ret;
- dev_info(dev, "probe set to K = %d.%.2d", be16_to_cpu(val) / 100,
- be16_to_cpu(val) % 100);
+ val = be16_to_cpu(rval);
+ dev_info(dev, "probe set to K = %d.%.2d", val / 100, val % 100);
ret = regmap_read(data->regmap, ATLAS_REG_EC_CALIB_STATUS, &val);
if (ret)
{
unsigned int storage_bytes = data->chip->read_size;
unsigned int shift = chan->scan_type.shift + (chan->address * 8);
- unsigned int buf;
+ __be16 buf16;
+ __be32 buf32;
int ret;
- ret = spi_read(data->spi, (void *) &buf, storage_bytes);
- if (ret)
- return ret;
-
switch (storage_bytes) {
case 2:
- *val = be16_to_cpu(buf);
+ ret = spi_read(data->spi, (void *)&buf16, storage_bytes);
+ *val = be16_to_cpu(buf16);
break;
case 4:
- *val = be32_to_cpu(buf);
+ ret = spi_read(data->spi, (void *)&buf32, storage_bytes);
+ *val = be32_to_cpu(buf32);
break;
}
+ if (ret)
+ return ret;
+
/* check to be sure this is a valid reading */
if (*val & data->chip->status_bit)
return -EINVAL;
if (copy_from_user(sgl->lpage, user_addr + user_size -
sgl->lpage_size, sgl->lpage_size)) {
rc = -EFAULT;
- goto err_out1;
+ goto err_out2;
}
}
return 0;
+ err_out2:
+ __genwqe_free_consistent(cd, PAGE_SIZE, sgl->lpage,
+ sgl->lpage_dma_addr);
+ sgl->lpage = NULL;
+ sgl->lpage_dma_addr = 0;
err_out1:
__genwqe_free_consistent(cd, PAGE_SIZE, sgl->fpage,
sgl->fpage_dma_addr);
+ sgl->fpage = NULL;
+ sgl->fpage_dma_addr = 0;
err_out:
__genwqe_free_consistent(cd, sgl->sgl_size, sgl->sgl,
sgl->sgl_dma_addr);
+ sgl->sgl = NULL;
+ sgl->sgl_dma_addr = 0;
+ sgl->sgl_size = 0;
return -ENOMEM;
}
hisr = mei_txe_br_reg_read(hw, HISR_REG);
aliveness = mei_txe_aliveness_get(dev);
- if (hhisr & IPC_HHIER_SEC && aliveness)
+ if (hhisr & IPC_HHIER_SEC && aliveness) {
ipc_isr = mei_txe_sec_reg_read_silent(hw,
SEC_IPC_HOST_INT_STATUS_REG);
- else
+ } else {
ipc_isr = 0;
+ hhisr &= ~IPC_HHIER_SEC;
+ }
generated = generated ||
(hisr & HISR_INT_STS_MSK) ||
if (vmci_handle_is_invalid(*handle)) {
u32 context_id = vmci_get_context_id();
+ if (context_id == VMCI_INVALID_ID) {
+ pr_warn("Failed to get context ID\n");
+ result = VMCI_ERROR_NO_RESOURCES;
+ goto free_mem;
+ }
+
/* Let resource code allocate a free ID for us */
new_handle = vmci_make_handle(context_id, VMCI_INVALID_ID);
} else {
entry = container_of(resource, struct dbell_entry, resource);
- if (vmci_guest_code_active()) {
+ if (!hlist_unhashed(&entry->node)) {
int result;
dbell_index_table_remove(entry);
MODULE_AUTHOR("VMware, Inc.");
MODULE_DESCRIPTION("VMware Virtual Machine Communication Interface.");
-MODULE_VERSION("1.1.4.0-k");
+MODULE_VERSION("1.1.5.0-k");
MODULE_LICENSE("GPL v2");
fmvhdr->vol_type,
be32_to_cpu(fmvhdr->last_eb_bytes));
- if (!av)
- goto fail_bad;
- if (PTR_ERR(av) == -EINVAL) {
- ubi_err(ubi, "volume (ID %i) already exists",
- fmvhdr->vol_id);
+ if (IS_ERR(av)) {
+ if (PTR_ERR(av) == -EEXIST)
+ ubi_err(ubi, "volume (ID %i) already exists",
+ fmvhdr->vol_id);
+
goto fail_bad;
}
UNIPHIER_RESET_END,
};
-const struct uniphier_reset_data uniphier_pro5_mio_reset_data[] = {
+const struct uniphier_reset_data uniphier_pro5_sd_reset_data[] = {
UNIPHIER_MIO_RESET_SD(0, 0),
UNIPHIER_MIO_RESET_SD(1, 1),
UNIPHIER_MIO_RESET_EMMC_HW_RESET(6, 1),
.compatible = "socionext,uniphier-ld20-reset",
.data = uniphier_ld20_sys_reset_data,
},
- /* Media I/O reset */
+ /* Media I/O reset, SD reset */
{
.compatible = "socionext,uniphier-sld3-mio-reset",
.data = uniphier_sld3_mio_reset_data,
.data = uniphier_sld3_mio_reset_data,
},
{
- .compatible = "socionext,uniphier-pro5-mio-reset",
- .data = uniphier_pro5_mio_reset_data,
+ .compatible = "socionext,uniphier-pro5-sd-reset",
+ .data = uniphier_pro5_sd_reset_data,
},
{
- .compatible = "socionext,uniphier-pxs2-mio-reset",
- .data = uniphier_pro5_mio_reset_data,
+ .compatible = "socionext,uniphier-pxs2-sd-reset",
+ .data = uniphier_pro5_sd_reset_data,
},
{
.compatible = "socionext,uniphier-ld11-mio-reset",
.data = uniphier_sld3_mio_reset_data,
},
{
- .compatible = "socionext,uniphier-ld20-mio-reset",
- .data = uniphier_pro5_mio_reset_data,
+ .compatible = "socionext,uniphier-ld20-sd-reset",
+ .data = uniphier_pro5_sd_reset_data,
},
/* Peripheral reset */
{
hdata.type = heap->type;
hdata.heap_id = heap->id;
- ret = copy_to_user(&buffer[cnt],
- &hdata, sizeof(hdata));
+ if (copy_to_user(&buffer[cnt], &hdata, sizeof(hdata))) {
+ ret = -EFAULT;
+ goto out;
+ }
cnt++;
if (cnt >= max_cnt)
heap_pdev = of_platform_device_create(node, heaps[i].name,
&pdev->dev);
- if (!pdev)
+ if (!heap_pdev)
return ERR_PTR(-ENOMEM);
heap_pdev->dev.platform_data = &heaps[i];
pdev = of_find_device_by_node(np);
if (!pdev) {
pr_err("arche-platform device not found\n");
+ of_node_put(np);
return -ENODEV;
}
INIT_LIST_HEAD(&es2->arpcs);
spin_lock_init(&es2->arpc_lock);
- if (es2_arpc_in_enable(es2))
+ retval = es2_arpc_in_enable(es2);
+ if (retval)
goto error;
retval = gb_hd_add(hd);
ret = gb_gpio_irqchip_add(gpio, irqc, 0,
handle_level_irq, IRQ_TYPE_NONE);
if (ret) {
- dev_err(&connection->bundle->dev,
- "failed to add irq chip: %d\n", ret);
+ dev_err(&gbphy_dev->dev, "failed to add irq chip: %d\n", ret);
goto exit_line_free;
}
ret = gpiochip_add(gpio);
if (ret) {
- dev_err(&connection->bundle->dev,
- "failed to add gpio chip: %d\n", ret);
+ dev_err(&gbphy_dev->dev, "failed to add gpio chip: %d\n", ret);
goto exit_gpio_irqchip_remove;
}
return module;
err_put_interfaces:
- for (--i; i > 0; --i)
+ for (--i; i >= 0; --i)
gb_interface_put(module->interfaces[i]);
put_device(&module->dev);
minor = alloc_minor(gb_tty);
if (minor < 0) {
if (minor == -ENOSPC) {
- dev_err(&connection->bundle->dev,
+ dev_err(&gbphy_dev->dev,
"no more free minor numbers\n");
retval = -ENODEV;
} else {
case SCA3000_MEAS_MODE_OP_2:
*base_freq = info->option_mode_2_freq;
break;
+ default:
+ ret = -EINVAL;
}
error_ret:
return ret;
}
LUSTRE_RW_ATTR(xattr_cache);
-static ssize_t unstable_stats_show(struct kobject *kobj,
- struct attribute *attr,
- char *buf)
+static int ll_unstable_stats_seq_show(struct seq_file *m, void *v)
{
- struct ll_sb_info *sbi = container_of(kobj, struct ll_sb_info,
- ll_kobj);
+ struct super_block *sb = m->private;
+ struct ll_sb_info *sbi = ll_s2sbi(sb);
struct cl_client_cache *cache = sbi->ll_cache;
long pages;
int mb;
pages = atomic_long_read(&cache->ccc_unstable_nr);
mb = (pages * PAGE_SIZE) >> 20;
- return sprintf(buf, "unstable_check: %8d\n"
- "unstable_pages: %12ld\n"
- "unstable_mb: %8d\n",
- cache->ccc_unstable_check, pages, mb);
+ seq_printf(m,
+ "unstable_check: %8d\n"
+ "unstable_pages: %12ld\n"
+ "unstable_mb: %8d\n",
+ cache->ccc_unstable_check, pages, mb);
+
+ return 0;
}
-static ssize_t unstable_stats_store(struct kobject *kobj,
- struct attribute *attr,
- const char *buffer,
- size_t count)
+static ssize_t ll_unstable_stats_seq_write(struct file *file,
+ const char __user *buffer,
+ size_t count, loff_t *off)
{
- struct ll_sb_info *sbi = container_of(kobj, struct ll_sb_info,
- ll_kobj);
+ struct super_block *sb = ((struct seq_file *)file->private_data)->private;
+ struct ll_sb_info *sbi = ll_s2sbi(sb);
char kernbuf[128];
int val, rc;
return count;
}
-LUSTRE_RW_ATTR(unstable_stats);
+LPROC_SEQ_FOPS(ll_unstable_stats);
static ssize_t root_squash_show(struct kobject *kobj, struct attribute *attr,
char *buf)
/* { "filegroups", lprocfs_rd_filegroups, 0, 0 }, */
{ "max_cached_mb", &ll_max_cached_mb_fops, NULL },
{ "statahead_stats", &ll_statahead_stats_fops, NULL, 0 },
+ { "unstable_stats", &ll_unstable_stats_fops, NULL },
{ "sbi_flags", &ll_sbi_flags_fops, NULL, 0 },
{ .name = "nosquash_nids",
.fops = &ll_nosquash_nids_fops },
&lustre_attr_max_easize.attr,
&lustre_attr_default_easize.attr,
&lustre_attr_xattr_cache.attr,
- &lustre_attr_unstable_stats.attr,
&lustre_attr_root_squash.attr,
NULL,
};
clients_count++;
- destroy_workqueue(hif_workqueue);
_fail_:
return result;
}
struct pci_dev *pdev = to_pci_dev(port->dev);
int ret;
- ret = pci_alloc_irq_vectors(pdev, 1, 1, 0);
+ ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
if (ret < 0)
return ret;
.name = "16550A",
.fifo_size = 16,
.tx_loadsz = 16,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
.rxtrig_bytes = {1, 4, 8, 14},
.flags = UART_CAP_FIFO,
},
case UART_LCR:
valshift = UNIPHIER_UART_LCR_SHIFT;
/* Divisor latch access bit does not exist. */
- value &= ~(UART_LCR_DLAB << valshift);
+ value &= ~UART_LCR_DLAB;
/* fall through */
case UART_MCR:
offset = UNIPHIER_UART_LCR_MCR;
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!regs) {
- dev_err(dev, "failed to get memory resource");
+ dev_err(dev, "failed to get memory resource\n");
return -EINVAL;
}
config SERIAL_STM32
tristate "STMicroelectronics STM32 serial port support"
select SERIAL_CORE
+ depends on HAS_DMA
depends on ARM || COMPILE_TEST
help
This driver is for the on-chip Serial Controller on
mode |= ATMEL_US_USMODE_RS485;
} else if (termios->c_cflag & CRTSCTS) {
/* RS232 with hardware handshake (RTS/CTS) */
- if (atmel_use_dma_rx(port) && !atmel_use_fifo(port)) {
- dev_info(port->dev, "not enabling hardware flow control because DMA is used");
- termios->c_cflag &= ~CRTSCTS;
- } else {
+ if (atmel_use_fifo(port) &&
+ !mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS)) {
+ /*
+ * with ATMEL_US_USMODE_HWHS set, the controller will
+ * be able to drive the RTS pin high/low when the RX
+ * FIFO is above RXFTHRES/below RXFTHRES2.
+ * It will also disable the transmitter when the CTS
+ * pin is high.
+ * This mode is not activated if CTS pin is a GPIO
+ * because in this case, the transmitter is always
+ * disabled (there must be an internal pull-up
+ * responsible for this behaviour).
+ * If the RTS pin is a GPIO, the controller won't be
+ * able to drive it according to the FIFO thresholds,
+ * but it will be handled by the driver.
+ */
mode |= ATMEL_US_USMODE_HWHS;
+ } else {
+ /*
+ * For platforms without FIFO, the flow control is
+ * handled by the driver.
+ */
+ mode |= ATMEL_US_USMODE_NORMAL;
}
} else {
/* RS232 without hadware handshake */
sport->dma_tx_bytes = uart_circ_chars_pending(xmit);
- if (xmit->tail < xmit->head) {
+ if (xmit->tail < xmit->head || xmit->head == 0) {
sport->dma_tx_nents = 1;
sg_init_one(sgl, xmit->buf + xmit->tail, sport->dma_tx_bytes);
} else {
sport->dma_tx_in_progress = true;
sport->dma_tx_cookie = dmaengine_submit(sport->dma_tx_desc);
dma_async_issue_pending(sport->dma_tx_chan);
-
}
static void lpuart_dma_tx_complete(void *arg)
},
(void *)MINNOW_UARTCLK,
},
+ { }
};
/* Return UART clock, checking for board specific clocks. */
{
struct sc16is7xx_port *s = gpiochip_get_data(chip);
struct uart_port *port = &s->p[0].port;
+ u8 state = sc16is7xx_port_read(port, SC16IS7XX_IOSTATE_REG);
- sc16is7xx_port_update(port, SC16IS7XX_IOSTATE_REG, BIT(offset),
- val ? BIT(offset) : 0);
+ if (val)
+ state |= BIT(offset);
+ else
+ state &= ~BIT(offset);
+ sc16is7xx_port_write(port, SC16IS7XX_IOSTATE_REG, state);
sc16is7xx_port_update(port, SC16IS7XX_IODIR_REG, BIT(offset),
BIT(offset));
* closed. No cookie for you.
*/
BUG_ON(!state);
- tty_wakeup(state->port.tty);
+ tty_port_tty_wakeup(&state->port);
}
static void uart_stop(struct tty_struct *tty)
if (port->ops->flush_buffer)
port->ops->flush_buffer(port);
uart_port_unlock(port, flags);
- tty_wakeup(tty);
+ tty_port_tty_wakeup(&state->port);
}
/*
uport->cons = drv->cons;
uport->minor = drv->tty_driver->minor_start + uport->line;
- port->console = uart_console(uport);
-
/*
* If this port is a console, then the spinlock is already
* initialised.
uart_configure_port(drv, state, uport);
+ port->console = uart_console(uport);
+
num_groups = 2;
if (uport->attr_group)
num_groups++;
struct stm32_usart_config cfg;
};
-#define UNDEF_REG ~0
+#define UNDEF_REG 0xff
/* Register offsets */
struct stm32_usart_info stm32f4_info = {
OF_EARLYCON_DECLARE(cdns, "xlnx,xuartps", cdns_early_console_setup);
OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p8", cdns_early_console_setup);
OF_EARLYCON_DECLARE(cdns, "cdns,uart-r1p12", cdns_early_console_setup);
+OF_EARLYCON_DECLARE(cdns, "xlnx,zynqmp-uart", cdns_early_console_setup);
/**
* cdns_uart_console_write - perform write operation
{ .compatible = "xlnx,xuartps", },
{ .compatible = "cdns,uart-r1p8", },
{ .compatible = "cdns,uart-r1p12", .data = &zynqmp_uart_def },
+ { .compatible = "xlnx,zynqmp-uart", .data = &zynqmp_uart_def },
{}
};
MODULE_DEVICE_TABLE(of, cdns_uart_of_match);
if (new_cols == vc->vc_cols && new_rows == vc->vc_rows)
return 0;
+ if (new_screen_size > (4 << 20))
+ return -EINVAL;
newscreen = kmalloc(new_screen_size, GFP_USER);
if (!newscreen)
return -ENOMEM;
+ if (vc == sel_cons)
+ clear_selection();
+
old_rows = vc->vc_rows;
old_row_size = vc->vc_size_row;
break;
case 3: /* erase scroll-back buffer (and whole display) */
scr_memsetw(vc->vc_screenbuf, vc->vc_video_erase_char,
- vc->vc_screenbuf_size >> 1);
+ vc->vc_screenbuf_size);
set_origin(vc);
if (con_is_visible(vc))
update_screen(vc);
if (hcd) {
usb_remove_hcd(hcd);
+ ci->role = CI_ROLE_END;
+ synchronize_irq(ci->irq);
usb_put_hcd(hcd);
if (ci->platdata->reg_vbus && !ci_otg_is_fsm_mode(ci) &&
(ci->platdata->flags & CI_HDRC_TURN_VBUS_EARLY_ON))
*/
void dwc2_force_dr_mode(struct dwc2_hsotg *hsotg)
{
+ bool ret;
+
switch (hsotg->dr_mode) {
case USB_DR_MODE_HOST:
- dwc2_force_mode(hsotg, true);
+ ret = dwc2_force_mode(hsotg, true);
+ /*
+ * NOTE: This is required for some rockchip soc based
+ * platforms on their host-only dwc2.
+ */
+ if (!ret)
+ msleep(50);
+
break;
case USB_DR_MODE_PERIPHERAL:
dwc2_force_mode(hsotg, false);
DWC2_L3, /* Off state */
};
+/*
+ * Gadget periodic tx fifo sizes as used by legacy driver
+ * EP0 is not included
+ */
+#define DWC2_G_P_LEGACY_TX_FIFO_SIZE {256, 256, 256, 256, 768, 768, 768, \
+ 768, 0, 0, 0, 0, 0, 0, 0}
+
/* Gadget ep0 states */
enum dwc2_ep0_state {
DWC2_EP0_SETUP,
*/
static void dwc2_hsotg_init_fifo(struct dwc2_hsotg *hsotg)
{
- unsigned int fifo;
+ unsigned int ep;
unsigned int addr;
int timeout;
- u32 dptxfsizn;
u32 val;
/* Reset fifo map if not correctly cleared during previous session */
* them to endpoints dynamically according to maxpacket size value of
* given endpoint.
*/
- for (fifo = 1; fifo < MAX_EPS_CHANNELS; fifo++) {
- dptxfsizn = dwc2_readl(hsotg->regs + DPTXFSIZN(fifo));
-
- val = (dptxfsizn & FIFOSIZE_DEPTH_MASK) | addr;
- addr += dptxfsizn >> FIFOSIZE_DEPTH_SHIFT;
-
- if (addr > hsotg->fifo_mem)
- break;
+ for (ep = 1; ep < MAX_EPS_CHANNELS; ep++) {
+ if (!hsotg->g_tx_fifo_sz[ep])
+ continue;
+ val = addr;
+ val |= hsotg->g_tx_fifo_sz[ep] << FIFOSIZE_DEPTH_SHIFT;
+ WARN_ONCE(addr + hsotg->g_tx_fifo_sz[ep] > hsotg->fifo_mem,
+ "insufficient fifo memory");
+ addr += hsotg->g_tx_fifo_sz[ep];
- dwc2_writel(val, hsotg->regs + DPTXFSIZN(fifo));
+ dwc2_writel(val, hsotg->regs + DPTXFSIZN(ep));
}
/*
static void dwc2_hsotg_of_probe(struct dwc2_hsotg *hsotg)
{
struct device_node *np = hsotg->dev->of_node;
+ u32 len = 0;
+ u32 i = 0;
/* Enable dma if requested in device tree */
hsotg->g_using_dma = of_property_read_bool(np, "g-use-dma");
+ /*
+ * Register TX periodic fifo size per endpoint.
+ * EP0 is excluded since it has no fifo configuration.
+ */
+ if (!of_find_property(np, "g-tx-fifo-size", &len))
+ goto rx_fifo;
+
+ len /= sizeof(u32);
+
+ /* Read tx fifo sizes other than ep0 */
+ if (of_property_read_u32_array(np, "g-tx-fifo-size",
+ &hsotg->g_tx_fifo_sz[1], len))
+ goto rx_fifo;
+
+ /* Add ep0 */
+ len++;
+
+ /* Make remaining TX fifos unavailable */
+ if (len < MAX_EPS_CHANNELS) {
+ for (i = len; i < MAX_EPS_CHANNELS; i++)
+ hsotg->g_tx_fifo_sz[i] = 0;
+ }
+
+rx_fifo:
/* Register RX fifo size */
of_property_read_u32(np, "g-rx-fifo-size", &hsotg->g_rx_fifo_sz);
struct device *dev = hsotg->dev;
int epnum;
int ret;
+ int i;
+ u32 p_tx_fifo[] = DWC2_G_P_LEGACY_TX_FIFO_SIZE;
/* Initialize to legacy fifo configuration values */
hsotg->g_rx_fifo_sz = 2048;
hsotg->g_np_g_tx_fifo_sz = 1024;
+ memcpy(&hsotg->g_tx_fifo_sz[1], p_tx_fifo, sizeof(p_tx_fifo));
/* Device tree specific probe */
dwc2_hsotg_of_probe(hsotg);
dev_dbg(dev, "NonPeriodic TXFIFO size: %d\n",
hsotg->g_np_g_tx_fifo_sz);
dev_dbg(dev, "RXFIFO size: %d\n", hsotg->g_rx_fifo_sz);
+ for (i = 0; i < MAX_EPS_CHANNELS; i++)
+ dev_dbg(dev, "Periodic TXFIFO%2d size: %d\n", i,
+ hsotg->g_tx_fifo_sz[i]);
hsotg->gadget.max_speed = USB_SPEED_HIGH;
hsotg->gadget.ops = &dwc2_hsotg_gadget_ops;
req->trb = trb;
req->trb_dma = dwc3_trb_dma_offset(dep, trb);
req->first_trb_index = dep->trb_enqueue;
+ dep->queued_requests++;
}
dwc3_ep_inc_enq(dep);
trb->ctrl |= DWC3_TRB_CTRL_HWO;
- dep->queued_requests++;
-
trace_dwc3_prepare_trb(dep, trb);
}
list_add_tail(&req->list, &dep->pending_list);
- if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
- dep->flags & DWC3_EP_PENDING_REQUEST) {
- if (list_empty(&dep->started_list)) {
+ /*
+ * NOTICE: Isochronous endpoints should NEVER be prestarted. We must
+ * wait for a XferNotReady event so we will know what's the current
+ * (micro-)frame number.
+ *
+ * Without this trick, we are very, very likely gonna get Bus Expiry
+ * errors which will force us issue EndTransfer command.
+ */
+ if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) {
+ if ((dep->flags & DWC3_EP_PENDING_REQUEST) &&
+ list_empty(&dep->started_list)) {
dwc3_stop_active_transfer(dwc, dep->number, true);
dep->flags = DWC3_EP_ENABLED;
}
unsigned int s_pkt = 0;
unsigned int trb_status;
- dep->queued_requests--;
dwc3_ep_inc_deq(dep);
+
+ if (req->trb == trb)
+ dep->queued_requests--;
+
trace_dwc3_complete_trb(dep, trb);
/*
kfree(dwc->setup_buf);
err2:
- dma_free_coherent(dwc->dev, sizeof(*dwc->ep0_trb),
+ dma_free_coherent(dwc->dev, sizeof(*dwc->ep0_trb) * 2,
dwc->ep0_trb, dwc->ep0_trb_addr);
err1:
kfree(dwc->setup_buf);
kfree(dwc->zlp_buf);
- dma_free_coherent(dwc->dev, sizeof(*dwc->ep0_trb),
+ dma_free_coherent(dwc->dev, sizeof(*dwc->ep0_trb) * 2,
dwc->ep0_trb, dwc->ep0_trb_addr);
dma_free_coherent(dwc->dev, sizeof(*dwc->ctrl_req),
/*
* Buffer for holding data from partial reads which may happen since
* we’re rounding user read requests to a multiple of a max packet size.
+ *
+ * The pointer is initialised with NULL value and may be set by
+ * __ffs_epfile_read_data function to point to a temporary buffer.
+ *
+ * In normal operation, calls to __ffs_epfile_read_buffered will consume
+ * data from said buffer and eventually free it. Importantly, while the
+ * function is using the buffer, it sets the pointer to NULL. This is
+ * all right since __ffs_epfile_read_data and __ffs_epfile_read_buffered
+ * can never run concurrently (they are synchronised by epfile->mutex)
+ * so the latter will not assign a new value to the pointer.
+ *
+ * Meanwhile ffs_func_eps_disable frees the buffer (if the pointer is
+ * valid) and sets the pointer to READ_BUFFER_DROP value. This special
+ * value is crux of the synchronisation between ffs_func_eps_disable and
+ * __ffs_epfile_read_data.
+ *
+ * Once __ffs_epfile_read_data is about to finish it will try to set the
+ * pointer back to its old value (as described above), but seeing as the
+ * pointer is not-NULL (namely READ_BUFFER_DROP) it will instead free
+ * the buffer.
+ *
+ * == State transitions ==
+ *
+ * • ptr == NULL: (initial state)
+ * â—¦ __ffs_epfile_read_buffer_free: go to ptr == DROP
+ * â—¦ __ffs_epfile_read_buffered: nop
+ * â—¦ __ffs_epfile_read_data allocates temp buffer: go to ptr == buf
+ * ◦ reading finishes: n/a, not in ‘and reading’ state
+ * • ptr == DROP:
+ * â—¦ __ffs_epfile_read_buffer_free: nop
+ * â—¦ __ffs_epfile_read_buffered: go to ptr == NULL
+ * â—¦ __ffs_epfile_read_data allocates temp buffer: free buf, nop
+ * ◦ reading finishes: n/a, not in ‘and reading’ state
+ * • ptr == buf:
+ * â—¦ __ffs_epfile_read_buffer_free: free buf, go to ptr == DROP
+ * â—¦ __ffs_epfile_read_buffered: go to ptr == NULL and reading
+ * â—¦ __ffs_epfile_read_data: n/a, __ffs_epfile_read_buffered
+ * is always called first
+ * ◦ reading finishes: n/a, not in ‘and reading’ state
+ * • ptr == NULL and reading:
+ * â—¦ __ffs_epfile_read_buffer_free: go to ptr == DROP and reading
+ * â—¦ __ffs_epfile_read_buffered: n/a, mutex is held
+ * â—¦ __ffs_epfile_read_data: n/a, mutex is held
+ * ◦ reading finishes and …
+ * … all data read: free buf, go to ptr == NULL
+ * … otherwise: go to ptr == buf and reading
+ * • ptr == DROP and reading:
+ * â—¦ __ffs_epfile_read_buffer_free: nop
+ * â—¦ __ffs_epfile_read_buffered: n/a, mutex is held
+ * â—¦ __ffs_epfile_read_data: n/a, mutex is held
+ * â—¦ reading finishes: free buf, go to ptr == DROP
*/
- struct ffs_buffer *read_buffer; /* P: epfile->mutex */
+ struct ffs_buffer *read_buffer;
+#define READ_BUFFER_DROP ((struct ffs_buffer *)ERR_PTR(-ESHUTDOWN))
char name[5];
schedule_work(&io_data->work);
}
+static void __ffs_epfile_read_buffer_free(struct ffs_epfile *epfile)
+{
+ /*
+ * See comment in struct ffs_epfile for full read_buffer pointer
+ * synchronisation story.
+ */
+ struct ffs_buffer *buf = xchg(&epfile->read_buffer, READ_BUFFER_DROP);
+ if (buf && buf != READ_BUFFER_DROP)
+ kfree(buf);
+}
+
/* Assumes epfile->mutex is held. */
static ssize_t __ffs_epfile_read_buffered(struct ffs_epfile *epfile,
struct iov_iter *iter)
{
- struct ffs_buffer *buf = epfile->read_buffer;
+ /*
+ * Null out epfile->read_buffer so ffs_func_eps_disable does not free
+ * the buffer while we are using it. See comment in struct ffs_epfile
+ * for full read_buffer pointer synchronisation story.
+ */
+ struct ffs_buffer *buf = xchg(&epfile->read_buffer, NULL);
ssize_t ret;
- if (!buf)
+ if (!buf || buf == READ_BUFFER_DROP)
return 0;
ret = copy_to_iter(buf->data, buf->length, iter);
if (buf->length == ret) {
kfree(buf);
- epfile->read_buffer = NULL;
- } else if (unlikely(iov_iter_count(iter))) {
+ return ret;
+ }
+
+ if (unlikely(iov_iter_count(iter))) {
ret = -EFAULT;
} else {
buf->length -= ret;
buf->data += ret;
}
+
+ if (cmpxchg(&epfile->read_buffer, NULL, buf))
+ kfree(buf);
+
return ret;
}
buf->length = data_len;
buf->data = buf->storage;
memcpy(buf->storage, data + ret, data_len);
- epfile->read_buffer = buf;
+
+ /*
+ * At this point read_buffer is NULL or READ_BUFFER_DROP (if
+ * ffs_func_eps_disable has been called in the meanwhile). See comment
+ * in struct ffs_epfile for full read_buffer pointer synchronisation
+ * story.
+ */
+ if (unlikely(cmpxchg(&epfile->read_buffer, NULL, buf)))
+ kfree(buf);
return ret;
}
ENTER();
- kfree(epfile->read_buffer);
- epfile->read_buffer = NULL;
+ __ffs_epfile_read_buffer_free(epfile);
ffs_data_closed(epfile->ffs);
return 0;
unsigned count = func->ffs->eps_count;
unsigned long flags;
+ spin_lock_irqsave(&func->ffs->eps_lock, flags);
do {
- if (epfile)
- mutex_lock(&epfile->mutex);
- spin_lock_irqsave(&func->ffs->eps_lock, flags);
/* pending requests get nuked */
if (likely(ep->ep))
usb_ep_disable(ep->ep);
++ep;
- spin_unlock_irqrestore(&func->ffs->eps_lock, flags);
if (epfile) {
epfile->ep = NULL;
- kfree(epfile->read_buffer);
- epfile->read_buffer = NULL;
- mutex_unlock(&epfile->mutex);
+ __ffs_epfile_read_buffer_free(epfile);
++epfile;
}
} while (--count);
+ spin_unlock_irqrestore(&func->ffs->eps_lock, flags);
}
static int ffs_func_eps_enable(struct ffs_function *func)
/* throttle high/super speed IRQ rate back slightly */
if (gadget_is_dualspeed(dev->gadget))
- req->no_interrupt = (dev->gadget->speed == USB_SPEED_HIGH ||
- dev->gadget->speed == USB_SPEED_SUPER)
+ req->no_interrupt = (((dev->gadget->speed == USB_SPEED_HIGH ||
+ dev->gadget->speed == USB_SPEED_SUPER)) &&
+ !list_empty(&dev->tx_reqs))
? ((atomic_read(&dev->tx_qlen) % dev->qmult) != 0)
: 0;
dev_err(&pdev->dev, "of_probe: name error(%d)\n", ret);
goto err;
}
- ep->ep.name = name;
+ ep->ep.name = kasprintf(GFP_KERNEL, "ep%d", ep->index);
ep->ep_regs = udc->regs + USBA_EPT_BASE(i);
ep->dma_regs = udc->regs + USBA_DMA_BASE(i);
#define DRIVER_DESC "EHCI generic platform driver"
#define EHCI_MAX_CLKS 4
-#define EHCI_MAX_RSTS 3
+#define EHCI_MAX_RSTS 4
#define hcd_to_ehci_priv(h) ((struct ehci_platform_priv *)hcd_to_ehci(h)->priv)
struct ehci_platform_priv {
ohci->num_ports = board->ports;
at91_start_hc(pdev);
+ /*
+ * The RemoteWakeupConnected bit has to be set explicitly
+ * before calling ohci_run. The reset value of this bit is 0.
+ */
+ ohci->hc_control = OHCI_CTRL_RWC;
+
retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
if (retval == 0) {
device_wakeup_enable(hcd->self.controller);
* REVISIT: some boards will be able to turn VBUS off...
*/
if (!ohci_at91->wakeup) {
- ohci->hc_control = ohci_readl(ohci, &ohci->regs->control);
- ohci->hc_control &= OHCI_CTRL_RWC;
- ohci_writel(ohci, ohci->hc_control, &ohci->regs->control);
ohci->rh_state = OHCI_RH_HALTED;
/* flush the writes */
static const char hcd_name [] = "ohci_hcd";
#define STATECHANGE_DELAY msecs_to_jiffies(300)
-#define IO_WATCHDOG_DELAY msecs_to_jiffies(250)
+#define IO_WATCHDOG_DELAY msecs_to_jiffies(275)
#include "ohci.h"
#include "pci-quirks.h"
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_RESUME);
spin_unlock_irqrestore(&xhci->lock, flags);
- msleep(20);
+ msleep(USB_RESUME_TIMEOUT);
spin_lock_irqsave(&xhci->lock, flags);
xhci_set_link_state(xhci, port_array, wIndex,
XDEV_U0);
return 0;
}
+/*
+ * Workaround for missing Cold Attach Status (CAS) if device re-plugged in S3.
+ * warm reset a USB3 device stuck in polling or compliance mode after resume.
+ * See Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
+ */
+static bool xhci_port_missing_cas_quirk(int port_index,
+ __le32 __iomem **port_array)
+{
+ u32 portsc;
+
+ portsc = readl(port_array[port_index]);
+
+ /* if any of these are set we are not stuck */
+ if (portsc & (PORT_CONNECT | PORT_CAS))
+ return false;
+
+ if (((portsc & PORT_PLS_MASK) != XDEV_POLLING) &&
+ ((portsc & PORT_PLS_MASK) != XDEV_COMP_MODE))
+ return false;
+
+ /* clear wakeup/change bits, and do a warm port reset */
+ portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
+ portsc |= PORT_WR;
+ writel(portsc, port_array[port_index]);
+ /* flush write */
+ readl(port_array[port_index]);
+ return true;
+}
+
int xhci_bus_resume(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
u32 temp;
temp = readl(port_array[port_index]);
+
+ /* warm reset CAS limited ports stuck in polling/compliance */
+ if ((xhci->quirks & XHCI_MISSING_CAS) &&
+ (hcd->speed >= HCD_USB3) &&
+ xhci_port_missing_cas_quirk(port_index, port_array)) {
+ xhci_dbg(xhci, "reset stuck port %d\n", port_index);
+ continue;
+ }
if (DEV_SUPERSPEED_ANY(temp))
temp &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS);
else
if (need_usb2_u3_exit) {
spin_unlock_irqrestore(&xhci->lock, flags);
- msleep(20);
+ msleep(USB_RESUME_TIMEOUT);
spin_lock_irqsave(&xhci->lock, flags);
}
#define PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI 0x8c31
#define PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI 0x9c31
+#define PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_XHCI 0x9cb1
#define PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI 0x22b5
#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI 0xa12f
#define PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI 0x9d2f
#define PCI_DEVICE_ID_INTEL_BROXTON_M_XHCI 0x0aa8
#define PCI_DEVICE_ID_INTEL_BROXTON_B_XHCI 0x1aa8
+#define PCI_DEVICE_ID_INTEL_APL_XHCI 0x5aa8
static const char hcd_name[] = "xhci_hcd";
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
- pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) {
+ (pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI ||
+ pdev->device == PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_XHCI)) {
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
xhci->quirks |= XHCI_SPURIOUS_WAKEUP;
}
pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI) {
xhci->quirks |= XHCI_SSIC_PORT_UNUSED;
}
+ if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
+ (pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI ||
+ pdev->device == PCI_DEVICE_ID_INTEL_APL_XHCI))
+ xhci->quirks |= XHCI_MISSING_CAS;
+
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_EJ168) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
#define XDEV_U2 (0x2 << 5)
#define XDEV_U3 (0x3 << 5)
#define XDEV_INACTIVE (0x6 << 5)
+#define XDEV_POLLING (0x7 << 5)
+#define XDEV_COMP_MODE (0xa << 5)
#define XDEV_RESUME (0xf << 5)
/* true: port has power (see HCC_PPC) */
#define PORT_POWER (1 << 9)
#define XHCI_MTK_HOST (1 << 21)
#define XHCI_SSIC_PORT_UNUSED (1 << 22)
#define XHCI_NO_64BIT_SUPPORT (1 << 23)
+#define XHCI_MISSING_CAS (1 << 24)
unsigned int num_active_eps;
unsigned int limit_active_eps;
/* There are two roothubs to keep track of bus suspend info for */
map_dma_buffer(request, musb, musb_ep);
+ pm_runtime_get_sync(musb->controller);
spin_lock_irqsave(&musb->lock, lockflags);
/* don't queue if the ep is down */
unlock:
spin_unlock_irqrestore(&musb->lock, lockflags);
+ pm_runtime_mark_last_busy(musb->controller);
+ pm_runtime_put_autosuspend(musb->controller);
+
return status;
}
}
musb->isr = omap2430_musb_interrupt;
phy_init(musb->phy);
+ phy_power_on(musb->phy);
l = musb_readl(musb->mregs, OTG_INTERFSEL);
struct musb_hdrc_platform_data *pdata = dev_get_platdata(dev);
struct omap_musb_board_data *data = pdata->board_data;
- if (!WARN_ON(!musb->phy))
- phy_power_on(musb->phy);
switch (glue->status) {
struct device *dev = musb->controller;
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
- if (!WARN_ON(!musb->phy))
- phy_power_off(musb->phy);
-
if (glue->status != MUSB_UNKNOWN)
omap_control_usb_set_mode(glue->control_otghs,
USB_MODE_DISCONNECT);
struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
omap2430_low_level_exit(musb);
+ phy_power_off(musb->phy);
phy_exit(musb->phy);
musb->phy = NULL;
cancel_work_sync(&glue->omap_musb_mailbox_work);
*
*/
+#include <linux/delay.h>
#include <linux/io.h>
#include "common.h"
#include "rcar3.h"
usbhs_write32(priv, UGCTRL2, UGCTRL2_RESERVED_3 | UGCTRL2_USB0SEL_OTG);
- if (enable)
+ if (enable) {
usbhs_bset(priv, LPSTS, LPSTS_SUSPM, LPSTS_SUSPM);
- else
+ /* The controller on R-Car Gen3 needs to wait up to 45 usec */
+ udelay(45);
+ } else {
usbhs_bset(priv, LPSTS, LPSTS_SUSPM, 0);
+ }
return 0;
}
u8 control;
int result;
- cp210x_read_u8_reg(port, CP210X_GET_MDMSTS, &control);
+ result = cp210x_read_u8_reg(port, CP210X_GET_MDMSTS, &control);
+ if (result)
+ return result;
result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
|((control & CONTROL_RTS) ? TIOCM_RTS : 0)
/* ekey Devices */
{ USB_DEVICE(FTDI_VID, FTDI_EKEY_CONV_USB_PID) },
/* Infineon Devices */
- { USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_PID, 1) },
+ { USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_TC1798_PID, 1) },
+ { USB_DEVICE_INTERFACE_NUMBER(INFINEON_VID, INFINEON_TRIBOARD_TC2X7_PID, 1) },
/* GE Healthcare devices */
{ USB_DEVICE(GE_HEALTHCARE_VID, GE_HEALTHCARE_NEMO_TRACKER_PID) },
/* Active Research (Actisense) devices */
/*
* Infineon Technologies
*/
-#define INFINEON_VID 0x058b
-#define INFINEON_TRIBOARD_PID 0x0028 /* DAS JTAG TriBoard TC1798 V1.0 */
+#define INFINEON_VID 0x058b
+#define INFINEON_TRIBOARD_TC1798_PID 0x0028 /* DAS JTAG TriBoard TC1798 V1.0 */
+#define INFINEON_TRIBOARD_TC2X7_PID 0x0043 /* DAS JTAG TriBoard TC2X7 V1.0 */
/*
* Acton Research Corp.
serial->disconnected = 0;
- usb_serial_console_init(serial->port[0]->minor);
+ if (num_ports > 0)
+ usb_serial_console_init(serial->port[0]->minor);
exit:
module_put(type->driver.owner);
return 0;
bo[itr] = bi1[itr] ^ bi2[itr];
}
+/* Scratch space for MAC calculations. */
+struct wusb_mac_scratch {
+ struct aes_ccm_b0 b0;
+ struct aes_ccm_b1 b1;
+ struct aes_ccm_a ax;
+};
+
/*
* CC-MAC function WUSB1.0[6.5]
*
* what sg[4] is for. Maybe there is a smarter way to do this.
*/
static int wusb_ccm_mac(struct crypto_skcipher *tfm_cbc,
- struct crypto_cipher *tfm_aes, void *mic,
+ struct crypto_cipher *tfm_aes,
+ struct wusb_mac_scratch *scratch,
+ void *mic,
const struct aes_ccm_nonce *n,
const struct aes_ccm_label *a, const void *b,
size_t blen)
{
int result = 0;
SKCIPHER_REQUEST_ON_STACK(req, tfm_cbc);
- struct aes_ccm_b0 b0;
- struct aes_ccm_b1 b1;
- struct aes_ccm_a ax;
struct scatterlist sg[4], sg_dst;
void *dst_buf;
size_t dst_size;
* These checks should be compile time optimized out
* ensure @a fills b1's mac_header and following fields
*/
- WARN_ON(sizeof(*a) != sizeof(b1) - sizeof(b1.la));
- WARN_ON(sizeof(b0) != sizeof(struct aes_ccm_block));
- WARN_ON(sizeof(b1) != sizeof(struct aes_ccm_block));
- WARN_ON(sizeof(ax) != sizeof(struct aes_ccm_block));
+ WARN_ON(sizeof(*a) != sizeof(scratch->b1) - sizeof(scratch->b1.la));
+ WARN_ON(sizeof(scratch->b0) != sizeof(struct aes_ccm_block));
+ WARN_ON(sizeof(scratch->b1) != sizeof(struct aes_ccm_block));
+ WARN_ON(sizeof(scratch->ax) != sizeof(struct aes_ccm_block));
result = -ENOMEM;
zero_padding = blen % sizeof(struct aes_ccm_block);
if (zero_padding)
zero_padding = sizeof(struct aes_ccm_block) - zero_padding;
- dst_size = blen + sizeof(b0) + sizeof(b1) + zero_padding;
+ dst_size = blen + sizeof(scratch->b0) + sizeof(scratch->b1) +
+ zero_padding;
dst_buf = kzalloc(dst_size, GFP_KERNEL);
if (!dst_buf)
goto error_dst_buf;
memset(iv, 0, sizeof(iv));
/* Setup B0 */
- b0.flags = 0x59; /* Format B0 */
- b0.ccm_nonce = *n;
- b0.lm = cpu_to_be16(0); /* WUSB1.0[6.5] sez l(m) is 0 */
+ scratch->b0.flags = 0x59; /* Format B0 */
+ scratch->b0.ccm_nonce = *n;
+ scratch->b0.lm = cpu_to_be16(0); /* WUSB1.0[6.5] sez l(m) is 0 */
/* Setup B1
*
* 14'--after clarification, it means to use A's contents
* for MAC Header, EO, sec reserved and padding.
*/
- b1.la = cpu_to_be16(blen + 14);
- memcpy(&b1.mac_header, a, sizeof(*a));
+ scratch->b1.la = cpu_to_be16(blen + 14);
+ memcpy(&scratch->b1.mac_header, a, sizeof(*a));
sg_init_table(sg, ARRAY_SIZE(sg));
- sg_set_buf(&sg[0], &b0, sizeof(b0));
- sg_set_buf(&sg[1], &b1, sizeof(b1));
+ sg_set_buf(&sg[0], &scratch->b0, sizeof(scratch->b0));
+ sg_set_buf(&sg[1], &scratch->b1, sizeof(scratch->b1));
sg_set_buf(&sg[2], b, blen);
/* 0 if well behaved :) */
sg_set_buf(&sg[3], bzero, zero_padding);
* POS Crypto API: size is assumed to be AES's block size.
* Thanks for documenting it -- tip taken from airo.c
*/
- ax.flags = 0x01; /* as per WUSB 1.0 spec */
- ax.ccm_nonce = *n;
- ax.counter = 0;
- crypto_cipher_encrypt_one(tfm_aes, (void *)&ax, (void *)&ax);
- bytewise_xor(mic, &ax, iv, 8);
+ scratch->ax.flags = 0x01; /* as per WUSB 1.0 spec */
+ scratch->ax.ccm_nonce = *n;
+ scratch->ax.counter = 0;
+ crypto_cipher_encrypt_one(tfm_aes, (void *)&scratch->ax,
+ (void *)&scratch->ax);
+ bytewise_xor(mic, &scratch->ax, iv, 8);
result = 8;
error_cbc_crypt:
kfree(dst_buf);
struct aes_ccm_nonce n = *_n;
struct crypto_skcipher *tfm_cbc;
struct crypto_cipher *tfm_aes;
+ struct wusb_mac_scratch *scratch;
u64 sfn = 0;
__le64 sfn_le;
printk(KERN_ERR "E: can't set AES key: %d\n", (int)result);
goto error_setkey_aes;
}
+ scratch = kmalloc(sizeof(*scratch), GFP_KERNEL);
+ if (!scratch) {
+ result = -ENOMEM;
+ goto error_alloc_scratch;
+ }
for (bitr = 0; bitr < (len + 63) / 64; bitr++) {
sfn_le = cpu_to_le64(sfn++);
memcpy(&n.sfn, &sfn_le, sizeof(n.sfn)); /* n.sfn++... */
- result = wusb_ccm_mac(tfm_cbc, tfm_aes, out + bytes,
+ result = wusb_ccm_mac(tfm_cbc, tfm_aes, scratch, out + bytes,
&n, a, b, blen);
if (result < 0)
goto error_ccm_mac;
bytes += result;
}
result = bytes;
+
+ kfree(scratch);
+error_alloc_scratch:
error_ccm_mac:
error_setkey_aes:
crypto_free_cipher(tfm_aes);
case VME_MASTER:
retval = vme_master_get(resource, &enabled, &base, &size,
&aspace, &cycle, &dwidth);
+ if (retval)
+ return 0;
return size;
break;
case VME_SLAVE:
retval = vme_slave_get(resource, &enabled, &base, &size,
&buf_base, &aspace, &cycle);
+ if (retval)
+ return 0;
return size;
break;
.open = kernfs_fop_open,
.release = kernfs_fop_release,
.poll = kernfs_fop_poll,
+ .fsync = noop_fsync,
};
/**
if (err != -ENOENT)
ubifs_err(c, "cannot find next direntry, error %d", err);
+ else
+ /*
+ * -ENOENT is a non-fatal error in this context, the TNC uses
+ * it to indicate that the cursor moved past the current directory
+ * and readdir() has to stop.
+ */
+ err = 0;
+
/* 2 is a special value indicating that there are no more direntries */
ctx->pos = 2;
projects / linux.git / commitdiff