source "drivers/gpu/drm/lima/Kconfig"
+source "drivers/gpu/drm/aspeed/Kconfig"
+
# Keep legacy drivers last
menuconfig DRM_LEGACY
obj-$(CONFIG_DRM_XEN) += xen/
obj-$(CONFIG_DRM_VBOXVIDEO) += vboxvideo/
obj-$(CONFIG_DRM_LIMA) += lima/
+obj-$(CONFIG_DRM_ASPEED_GFX) += aspeed/
--- /dev/null
+config DRM_ASPEED_GFX
+ tristate "ASPEED BMC Display Controller"
+ depends on DRM && OF
+ select DRM_KMS_HELPER
+ select DRM_KMS_CMA_HELPER
+ select DRM_PANEL
+ select DMA_CMA
+ select CMA
+ select MFD_SYSCON
+ help
+ Chose this option if you have an ASPEED AST2500 SOC Display
+ Controller (aka GFX).
+
+ If M is selected this module will be called aspeed_gfx.
--- /dev/null
+aspeed_gfx-y := aspeed_gfx_drv.o aspeed_gfx_crtc.o aspeed_gfx_out.o
+
+obj-$(CONFIG_DRM_ASPEED_GFX) += aspeed_gfx.o
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/* Copyright 2018 IBM Corporation */
+
+#include <drm/drm_device.h>
+#include <drm/drm_simple_kms_helper.h>
+
+struct aspeed_gfx {
+ void __iomem *base;
+ struct clk *clk;
+ struct reset_control *rst;
+ struct regmap *scu;
+
+ struct drm_simple_display_pipe pipe;
+ struct drm_connector connector;
+ struct drm_fbdev_cma *fbdev;
+};
+
+int aspeed_gfx_create_pipe(struct drm_device *drm);
+int aspeed_gfx_create_output(struct drm_device *drm);
+
+#define CRT_CTRL1 0x60 /* CRT Control I */
+#define CRT_CTRL2 0x64 /* CRT Control II */
+#define CRT_STATUS 0x68 /* CRT Status */
+#define CRT_MISC 0x6c /* CRT Misc Setting */
+#define CRT_HORIZ0 0x70 /* CRT Horizontal Total & Display Enable End */
+#define CRT_HORIZ1 0x74 /* CRT Horizontal Retrace Start & End */
+#define CRT_VERT0 0x78 /* CRT Vertical Total & Display Enable End */
+#define CRT_VERT1 0x7C /* CRT Vertical Retrace Start & End */
+#define CRT_ADDR 0x80 /* CRT Display Starting Address */
+#define CRT_OFFSET 0x84 /* CRT Display Offset & Terminal Count */
+#define CRT_THROD 0x88 /* CRT Threshold */
+#define CRT_XSCALE 0x8C /* CRT Scaling-Up Factor */
+#define CRT_CURSOR0 0x90 /* CRT Hardware Cursor X & Y Offset */
+#define CRT_CURSOR1 0x94 /* CRT Hardware Cursor X & Y Position */
+#define CRT_CURSOR2 0x98 /* CRT Hardware Cursor Pattern Address */
+#define CRT_9C 0x9C
+#define CRT_OSD_H 0xA0 /* CRT OSD Horizontal Start/End */
+#define CRT_OSD_V 0xA4 /* CRT OSD Vertical Start/End */
+#define CRT_OSD_ADDR 0xA8 /* CRT OSD Pattern Address */
+#define CRT_OSD_DISP 0xAC /* CRT OSD Offset */
+#define CRT_OSD_THRESH 0xB0 /* CRT OSD Threshold & Alpha */
+#define CRT_B4 0xB4
+#define CRT_STS_V 0xB8 /* CRT Status V */
+#define CRT_SCRATCH 0xBC /* Scratchpad */
+#define CRT_BB0_ADDR 0xD0 /* CRT Display BB0 Starting Address */
+#define CRT_BB1_ADDR 0xD4 /* CRT Display BB1 Starting Address */
+#define CRT_BB_COUNT 0xD8 /* CRT Display BB Terminal Count */
+#define OSD_COLOR1 0xE0 /* OSD Color Palette Index 1 & 0 */
+#define OSD_COLOR2 0xE4 /* OSD Color Palette Index 3 & 2 */
+#define OSD_COLOR3 0xE8 /* OSD Color Palette Index 5 & 4 */
+#define OSD_COLOR4 0xEC /* OSD Color Palette Index 7 & 6 */
+#define OSD_COLOR5 0xF0 /* OSD Color Palette Index 9 & 8 */
+#define OSD_COLOR6 0xF4 /* OSD Color Palette Index 11 & 10 */
+#define OSD_COLOR7 0xF8 /* OSD Color Palette Index 13 & 12 */
+#define OSD_COLOR8 0xFC /* OSD Color Palette Index 15 & 14 */
+
+/* CTRL1 */
+#define CRT_CTRL_EN BIT(0)
+#define CRT_CTRL_HW_CURSOR_EN BIT(1)
+#define CRT_CTRL_OSD_EN BIT(2)
+#define CRT_CTRL_INTERLACED BIT(3)
+#define CRT_CTRL_COLOR_RGB565 (0 << 7)
+#define CRT_CTRL_COLOR_YUV444 (1 << 7)
+#define CRT_CTRL_COLOR_XRGB8888 (2 << 7)
+#define CRT_CTRL_COLOR_RGB888 (3 << 7)
+#define CRT_CTRL_COLOR_YUV444_2RGB (5 << 7)
+#define CRT_CTRL_COLOR_YUV422 (7 << 7)
+#define CRT_CTRL_COLOR_MASK GENMASK(9, 7)
+#define CRT_CTRL_HSYNC_NEGATIVE BIT(16)
+#define CRT_CTRL_VSYNC_NEGATIVE BIT(17)
+#define CRT_CTRL_VERTICAL_INTR_EN BIT(30)
+#define CRT_CTRL_VERTICAL_INTR_STS BIT(31)
+
+/* CTRL2 */
+#define CRT_CTRL_DAC_EN BIT(0)
+#define CRT_CTRL_VBLANK_LINE(x) (((x) << 20) & CRT_CTRL_VBLANK_LINE_MASK)
+#define CRT_CTRL_VBLANK_LINE_MASK GENMASK(20, 31)
+
+/* CRT_HORIZ0 */
+#define CRT_H_TOTAL(x) (x)
+#define CRT_H_DE(x) ((x) << 16)
+
+/* CRT_HORIZ1 */
+#define CRT_H_RS_START(x) (x)
+#define CRT_H_RS_END(x) ((x) << 16)
+
+/* CRT_VIRT0 */
+#define CRT_V_TOTAL(x) (x)
+#define CRT_V_DE(x) ((x) << 16)
+
+/* CRT_VIRT1 */
+#define CRT_V_RS_START(x) (x)
+#define CRT_V_RS_END(x) ((x) << 16)
+
+/* CRT_OFFSET */
+#define CRT_DISP_OFFSET(x) (x)
+#define CRT_TERM_COUNT(x) ((x) << 16)
+
+/* CRT_THROD */
+#define CRT_THROD_LOW(x) (x)
+#define CRT_THROD_HIGH(x) ((x) << 8)
+
+/* Default Threshold Seting */
+#define G5_CRT_THROD_VAL (CRT_THROD_LOW(0x24) | CRT_THROD_HIGH(0x3C))
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <linux/clk.h>
+#include <linux/reset.h>
+#include <linux/regmap.h>
+
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_device.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_fourcc.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_panel.h>
+#include <drm/drm_simple_kms_helper.h>
+#include <drm/drm_vblank.h>
+
+#include "aspeed_gfx.h"
+
+static struct aspeed_gfx *
+drm_pipe_to_aspeed_gfx(struct drm_simple_display_pipe *pipe)
+{
+ return container_of(pipe, struct aspeed_gfx, pipe);
+}
+
+static int aspeed_gfx_set_pixel_fmt(struct aspeed_gfx *priv, u32 *bpp)
+{
+ struct drm_crtc *crtc = &priv->pipe.crtc;
+ struct drm_device *drm = crtc->dev;
+ const u32 format = crtc->primary->state->fb->format->format;
+ u32 ctrl1;
+
+ ctrl1 = readl(priv->base + CRT_CTRL1);
+ ctrl1 &= ~CRT_CTRL_COLOR_MASK;
+
+ switch (format) {
+ case DRM_FORMAT_RGB565:
+ dev_dbg(drm->dev, "Setting up RGB565 mode\n");
+ ctrl1 |= CRT_CTRL_COLOR_RGB565;
+ *bpp = 16;
+ break;
+ case DRM_FORMAT_XRGB8888:
+ dev_dbg(drm->dev, "Setting up XRGB8888 mode\n");
+ ctrl1 |= CRT_CTRL_COLOR_XRGB8888;
+ *bpp = 32;
+ break;
+ default:
+ dev_err(drm->dev, "Unhandled pixel format %08x\n", format);
+ return -EINVAL;
+ }
+
+ writel(ctrl1, priv->base + CRT_CTRL1);
+
+ return 0;
+}
+
+static void aspeed_gfx_enable_controller(struct aspeed_gfx *priv)
+{
+ u32 ctrl1 = readl(priv->base + CRT_CTRL1);
+ u32 ctrl2 = readl(priv->base + CRT_CTRL2);
+
+ /* SCU2C: set DAC source for display output to Graphics CRT (GFX) */
+ regmap_update_bits(priv->scu, 0x2c, BIT(16), BIT(16));
+
+ writel(ctrl1 | CRT_CTRL_EN, priv->base + CRT_CTRL1);
+ writel(ctrl2 | CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2);
+}
+
+static void aspeed_gfx_disable_controller(struct aspeed_gfx *priv)
+{
+ u32 ctrl1 = readl(priv->base + CRT_CTRL1);
+ u32 ctrl2 = readl(priv->base + CRT_CTRL2);
+
+ writel(ctrl1 & ~CRT_CTRL_EN, priv->base + CRT_CTRL1);
+ writel(ctrl2 & ~CRT_CTRL_DAC_EN, priv->base + CRT_CTRL2);
+
+ regmap_update_bits(priv->scu, 0x2c, BIT(16), 0);
+}
+
+static void aspeed_gfx_crtc_mode_set_nofb(struct aspeed_gfx *priv)
+{
+ struct drm_display_mode *m = &priv->pipe.crtc.state->adjusted_mode;
+ u32 ctrl1, d_offset, t_count, bpp;
+ int err;
+
+ err = aspeed_gfx_set_pixel_fmt(priv, &bpp);
+ if (err)
+ return;
+
+#if 0
+ /* TODO: we have only been able to test with the 40MHz USB clock. The
+ * clock is fixed, so we cannot adjust it here. */
+ clk_set_rate(priv->pixel_clk, m->crtc_clock * 1000);
+#endif
+
+ ctrl1 = readl(priv->base + CRT_CTRL1);
+ ctrl1 &= ~(CRT_CTRL_INTERLACED |
+ CRT_CTRL_HSYNC_NEGATIVE |
+ CRT_CTRL_VSYNC_NEGATIVE);
+
+ if (m->flags & DRM_MODE_FLAG_INTERLACE)
+ ctrl1 |= CRT_CTRL_INTERLACED;
+
+ if (!(m->flags & DRM_MODE_FLAG_PHSYNC))
+ ctrl1 |= CRT_CTRL_HSYNC_NEGATIVE;
+
+ if (!(m->flags & DRM_MODE_FLAG_PVSYNC))
+ ctrl1 |= CRT_CTRL_VSYNC_NEGATIVE;
+
+ writel(ctrl1, priv->base + CRT_CTRL1);
+
+ /* Horizontal timing */
+ writel(CRT_H_TOTAL(m->htotal - 1) | CRT_H_DE(m->hdisplay - 1),
+ priv->base + CRT_HORIZ0);
+ writel(CRT_H_RS_START(m->hsync_start - 1) | CRT_H_RS_END(m->hsync_end),
+ priv->base + CRT_HORIZ1);
+
+
+ /* Vertical timing */
+ writel(CRT_V_TOTAL(m->vtotal - 1) | CRT_V_DE(m->vdisplay - 1),
+ priv->base + CRT_VERT0);
+ writel(CRT_V_RS_START(m->vsync_start) | CRT_V_RS_END(m->vsync_end),
+ priv->base + CRT_VERT1);
+
+ /*
+ * Display Offset: address difference between consecutive scan lines
+ * Terminal Count: memory size of one scan line
+ */
+ d_offset = m->hdisplay * bpp / 8;
+ t_count = (m->hdisplay * bpp + 127) / 128;
+ writel(CRT_DISP_OFFSET(d_offset) | CRT_TERM_COUNT(t_count),
+ priv->base + CRT_OFFSET);
+
+ /*
+ * Threshold: FIFO thresholds of refill and stop (16 byte chunks
+ * per line, rounded up)
+ */
+ writel(G5_CRT_THROD_VAL, priv->base + CRT_THROD);
+}
+
+static void aspeed_gfx_pipe_enable(struct drm_simple_display_pipe *pipe,
+ struct drm_crtc_state *crtc_state,
+ struct drm_plane_state *plane_state)
+{
+ struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+ struct drm_crtc *crtc = &pipe->crtc;
+
+ aspeed_gfx_crtc_mode_set_nofb(priv);
+ aspeed_gfx_enable_controller(priv);
+ drm_crtc_vblank_on(crtc);
+}
+
+static void aspeed_gfx_pipe_disable(struct drm_simple_display_pipe *pipe)
+{
+ struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+ struct drm_crtc *crtc = &pipe->crtc;
+
+ drm_crtc_vblank_off(crtc);
+ aspeed_gfx_disable_controller(priv);
+}
+
+static void aspeed_gfx_pipe_update(struct drm_simple_display_pipe *pipe,
+ struct drm_plane_state *plane_state)
+{
+ struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+ struct drm_crtc *crtc = &pipe->crtc;
+ struct drm_framebuffer *fb = pipe->plane.state->fb;
+ struct drm_pending_vblank_event *event;
+ struct drm_gem_cma_object *gem;
+
+ spin_lock_irq(&crtc->dev->event_lock);
+ event = crtc->state->event;
+ if (event) {
+ crtc->state->event = NULL;
+
+ if (drm_crtc_vblank_get(crtc) == 0)
+ drm_crtc_arm_vblank_event(crtc, event);
+ else
+ drm_crtc_send_vblank_event(crtc, event);
+ }
+ spin_unlock_irq(&crtc->dev->event_lock);
+
+ if (!fb)
+ return;
+
+ gem = drm_fb_cma_get_gem_obj(fb, 0);
+ if (!gem)
+ return;
+ writel(gem->paddr, priv->base + CRT_ADDR);
+}
+
+static int aspeed_gfx_enable_vblank(struct drm_simple_display_pipe *pipe)
+{
+ struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+ u32 reg = readl(priv->base + CRT_CTRL1);
+
+ /* Clear pending VBLANK IRQ */
+ writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1);
+
+ reg |= CRT_CTRL_VERTICAL_INTR_EN;
+ writel(reg, priv->base + CRT_CTRL1);
+
+ return 0;
+}
+
+static void aspeed_gfx_disable_vblank(struct drm_simple_display_pipe *pipe)
+{
+ struct aspeed_gfx *priv = drm_pipe_to_aspeed_gfx(pipe);
+ u32 reg = readl(priv->base + CRT_CTRL1);
+
+ reg &= ~CRT_CTRL_VERTICAL_INTR_EN;
+ writel(reg, priv->base + CRT_CTRL1);
+
+ /* Clear pending VBLANK IRQ */
+ writel(reg | CRT_CTRL_VERTICAL_INTR_STS, priv->base + CRT_CTRL1);
+}
+
+static struct drm_simple_display_pipe_funcs aspeed_gfx_funcs = {
+ .enable = aspeed_gfx_pipe_enable,
+ .disable = aspeed_gfx_pipe_disable,
+ .update = aspeed_gfx_pipe_update,
+ .prepare_fb = drm_gem_fb_simple_display_pipe_prepare_fb,
+ .enable_vblank = aspeed_gfx_enable_vblank,
+ .disable_vblank = aspeed_gfx_disable_vblank,
+};
+
+static const uint32_t aspeed_gfx_formats[] = {
+ DRM_FORMAT_XRGB8888,
+ DRM_FORMAT_RGB565,
+};
+
+int aspeed_gfx_create_pipe(struct drm_device *drm)
+{
+ struct aspeed_gfx *priv = drm->dev_private;
+
+ return drm_simple_display_pipe_init(drm, &priv->pipe, &aspeed_gfx_funcs,
+ aspeed_gfx_formats,
+ ARRAY_SIZE(aspeed_gfx_formats),
+ NULL,
+ &priv->connector);
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_device.h>
+#include <drm/drm_fb_cma_helper.h>
+#include <drm/drm_fb_helper.h>
+#include <drm/drm_gem_cma_helper.h>
+#include <drm/drm_gem_framebuffer_helper.h>
+#include <drm/drm_probe_helper.h>
+#include <drm/drm_simple_kms_helper.h>
+#include <drm/drm_vblank.h>
+#include <drm/drm_drv.h>
+
+#include "aspeed_gfx.h"
+
+/**
+ * DOC: ASPEED GFX Driver
+ *
+ * This driver is for the ASPEED BMC SoC's 'GFX' display hardware, also called
+ * the 'SOC Display Controller' in the datasheet. This driver runs on the ARM
+ * based BMC systems, unlike the ast driver which runs on a host CPU and is for
+ * a PCIe graphics device.
+ *
+ * The AST2500 supports a total of 3 output paths:
+ *
+ * 1. VGA output, the output target can choose either or both to the DAC
+ * or DVO interface.
+ *
+ * 2. Graphics CRT output, the output target can choose either or both to
+ * the DAC or DVO interface.
+ *
+ * 3. Video input from DVO, the video input can be used for video engine
+ * capture or DAC display output.
+ *
+ * Output options are selected in SCU2C.
+ *
+ * The "VGA mode" device is the PCI attached controller. The "Graphics CRT"
+ * is the ARM's internal display controller.
+ *
+ * The driver only supports a simple configuration consisting of a 40MHz
+ * pixel clock, fixed by hardware limitations, and the VGA output path.
+ *
+ * The driver was written with the 'AST2500 Software Programming Guide' v17,
+ * which is available under NDA from ASPEED.
+ */
+
+static const struct drm_mode_config_funcs aspeed_gfx_mode_config_funcs = {
+ .fb_create = drm_gem_fb_create,
+ .atomic_check = drm_atomic_helper_check,
+ .atomic_commit = drm_atomic_helper_commit,
+};
+
+static void aspeed_gfx_setup_mode_config(struct drm_device *drm)
+{
+ drm_mode_config_init(drm);
+
+ drm->mode_config.min_width = 0;
+ drm->mode_config.min_height = 0;
+ drm->mode_config.max_width = 800;
+ drm->mode_config.max_height = 600;
+ drm->mode_config.funcs = &aspeed_gfx_mode_config_funcs;
+}
+
+static irqreturn_t aspeed_gfx_irq_handler(int irq, void *data)
+{
+ struct drm_device *drm = data;
+ struct aspeed_gfx *priv = drm->dev_private;
+ u32 reg;
+
+ reg = readl(priv->base + CRT_CTRL1);
+
+ if (reg & CRT_CTRL_VERTICAL_INTR_STS) {
+ drm_crtc_handle_vblank(&priv->pipe.crtc);
+ writel(reg, priv->base + CRT_CTRL1);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+
+
+static int aspeed_gfx_load(struct drm_device *drm)
+{
+ struct platform_device *pdev = to_platform_device(drm->dev);
+ struct aspeed_gfx *priv;
+ struct resource *res;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ drm->dev_private = priv;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ priv->base = devm_ioremap_resource(drm->dev, res);
+ if (IS_ERR(priv->base))
+ return PTR_ERR(priv->base);
+
+ priv->scu = syscon_regmap_lookup_by_compatible("aspeed,ast2500-scu");
+ if (IS_ERR(priv->scu)) {
+ dev_err(&pdev->dev, "failed to find SCU regmap\n");
+ return PTR_ERR(priv->scu);
+ }
+
+ ret = of_reserved_mem_device_init(drm->dev);
+ if (ret) {
+ dev_err(&pdev->dev,
+ "failed to initialize reserved mem: %d\n", ret);
+ return ret;
+ }
+
+ ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32));
+ if (ret) {
+ dev_err(&pdev->dev, "failed to set DMA mask: %d\n", ret);
+ return ret;
+ }
+
+ priv->rst = devm_reset_control_get_exclusive(&pdev->dev, NULL);
+ if (IS_ERR(priv->rst)) {
+ dev_err(&pdev->dev,
+ "missing or invalid reset controller device tree entry");
+ return PTR_ERR(priv->rst);
+ }
+ reset_control_deassert(priv->rst);
+
+ priv->clk = devm_clk_get(drm->dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ dev_err(&pdev->dev,
+ "missing or invalid clk device tree entry");
+ return PTR_ERR(priv->clk);
+ }
+ clk_prepare_enable(priv->clk);
+
+ /* Sanitize control registers */
+ writel(0, priv->base + CRT_CTRL1);
+ writel(0, priv->base + CRT_CTRL2);
+
+ aspeed_gfx_setup_mode_config(drm);
+
+ ret = drm_vblank_init(drm, 1);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to initialise vblank\n");
+ return ret;
+ }
+
+ ret = aspeed_gfx_create_output(drm);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to create outputs\n");
+ return ret;
+ }
+
+ ret = aspeed_gfx_create_pipe(drm);
+ if (ret < 0) {
+ dev_err(drm->dev, "Cannot setup simple display pipe\n");
+ return ret;
+ }
+
+ ret = devm_request_irq(drm->dev, platform_get_irq(pdev, 0),
+ aspeed_gfx_irq_handler, 0, "aspeed gfx", drm);
+ if (ret < 0) {
+ dev_err(drm->dev, "Failed to install IRQ handler\n");
+ return ret;
+ }
+
+ drm_mode_config_reset(drm);
+
+ drm_fbdev_generic_setup(drm, 32);
+
+ return 0;
+}
+
+static void aspeed_gfx_unload(struct drm_device *drm)
+{
+ drm_kms_helper_poll_fini(drm);
+ drm_mode_config_cleanup(drm);
+
+ drm->dev_private = NULL;
+}
+
+DEFINE_DRM_GEM_CMA_FOPS(fops);
+
+static struct drm_driver aspeed_gfx_driver = {
+ .driver_features = DRIVER_GEM | DRIVER_MODESET |
+ DRIVER_PRIME | DRIVER_ATOMIC,
+ .gem_create_object = drm_cma_gem_create_object_default_funcs,
+ .dumb_create = drm_gem_cma_dumb_create,
+ .prime_handle_to_fd = drm_gem_prime_handle_to_fd,
+ .prime_fd_to_handle = drm_gem_prime_fd_to_handle,
+ .gem_prime_import_sg_table = drm_gem_cma_prime_import_sg_table,
+ .gem_prime_mmap = drm_gem_prime_mmap,
+ .fops = &fops,
+ .name = "aspeed-gfx-drm",
+ .desc = "ASPEED GFX DRM",
+ .date = "20180319",
+ .major = 1,
+ .minor = 0,
+};
+
+static const struct of_device_id aspeed_gfx_match[] = {
+ { .compatible = "aspeed,ast2500-gfx" },
+ { }
+};
+
+static int aspeed_gfx_probe(struct platform_device *pdev)
+{
+ struct drm_device *drm;
+ int ret;
+
+ drm = drm_dev_alloc(&aspeed_gfx_driver, &pdev->dev);
+ if (IS_ERR(drm))
+ return PTR_ERR(drm);
+
+ ret = aspeed_gfx_load(drm);
+ if (ret)
+ goto err_free;
+
+ ret = drm_dev_register(drm, 0);
+ if (ret)
+ goto err_unload;
+
+ return 0;
+
+err_unload:
+ aspeed_gfx_unload(drm);
+err_free:
+ drm_dev_put(drm);
+
+ return ret;
+}
+
+static int aspeed_gfx_remove(struct platform_device *pdev)
+{
+ struct drm_device *drm = platform_get_drvdata(pdev);
+
+ drm_dev_unregister(drm);
+ aspeed_gfx_unload(drm);
+ drm_dev_put(drm);
+
+ return 0;
+}
+
+static struct platform_driver aspeed_gfx_platform_driver = {
+ .probe = aspeed_gfx_probe,
+ .remove = aspeed_gfx_remove,
+ .driver = {
+ .name = "aspeed_gfx",
+ .of_match_table = aspeed_gfx_match,
+ },
+};
+
+module_platform_driver(aspeed_gfx_platform_driver);
+
+MODULE_AUTHOR("Joel Stanley <joel@jms.id.au>");
+MODULE_DESCRIPTION("ASPEED BMC DRM/KMS driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright 2018 IBM Corporation
+
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_connector.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_probe_helper.h>
+
+#include "aspeed_gfx.h"
+
+static int aspeed_gfx_get_modes(struct drm_connector *connector)
+{
+ return drm_add_modes_noedid(connector, 800, 600);
+}
+
+static const struct
+drm_connector_helper_funcs aspeed_gfx_connector_helper_funcs = {
+ .get_modes = aspeed_gfx_get_modes,
+};
+
+static const struct drm_connector_funcs aspeed_gfx_connector_funcs = {
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+int aspeed_gfx_create_output(struct drm_device *drm)
+{
+ struct aspeed_gfx *priv = drm->dev_private;
+ int ret;
+
+ priv->connector.dpms = DRM_MODE_DPMS_OFF;
+ priv->connector.polled = 0;
+ drm_connector_helper_add(&priv->connector,
+ &aspeed_gfx_connector_helper_funcs);
+ ret = drm_connector_init(drm, &priv->connector,
+ &aspeed_gfx_connector_funcs,
+ DRM_MODE_CONNECTOR_Unknown);
+ return ret;
+}
projects / linux.git / commitdiff