--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for ST MIPID02 CSI-2 to PARALLEL bridge
+ *
+ * Copyright (C) STMicroelectronics SA 2019
+ * Authors: Mickael Guene <mickael.guene@st.com>
+ * for STMicroelectronics.
+ *
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <media/v4l2-async.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-subdev.h>
+
+#define MIPID02_CLK_LANE_WR_REG1 0x01
+#define MIPID02_CLK_LANE_REG1 0x02
+#define MIPID02_CLK_LANE_REG3 0x04
+#define MIPID02_DATA_LANE0_REG1 0x05
+#define MIPID02_DATA_LANE0_REG2 0x06
+#define MIPID02_DATA_LANE1_REG1 0x09
+#define MIPID02_DATA_LANE1_REG2 0x0a
+#define MIPID02_MODE_REG1 0x14
+#define MIPID02_MODE_REG2 0x15
+#define MIPID02_DATA_ID_RREG 0x17
+#define MIPID02_DATA_SELECTION_CTRL 0x19
+#define MIPID02_PIX_WIDTH_CTRL 0x1e
+#define MIPID02_PIX_WIDTH_CTRL_EMB 0x1f
+
+/* Bits definition for MIPID02_CLK_LANE_REG1 */
+#define CLK_ENABLE BIT(0)
+/* Bits definition for MIPID02_CLK_LANE_REG3 */
+#define CLK_MIPI_CSI BIT(1)
+/* Bits definition for MIPID02_DATA_LANE0_REG1 */
+#define DATA_ENABLE BIT(0)
+/* Bits definition for MIPID02_DATA_LANEx_REG2 */
+#define DATA_MIPI_CSI BIT(0)
+/* Bits definition for MIPID02_MODE_REG1 */
+#define MODE_DATA_SWAP BIT(2)
+#define MODE_NO_BYPASS BIT(6)
+/* Bits definition for MIPID02_MODE_REG2 */
+#define MODE_HSYNC_ACTIVE_HIGH BIT(1)
+#define MODE_VSYNC_ACTIVE_HIGH BIT(2)
+/* Bits definition for MIPID02_DATA_SELECTION_CTRL */
+#define SELECTION_MANUAL_DATA BIT(2)
+#define SELECTION_MANUAL_WIDTH BIT(3)
+
+static const u32 mipid02_supported_fmt_codes[] = {
+ MEDIA_BUS_FMT_SBGGR8_1X8, MEDIA_BUS_FMT_SGBRG8_1X8,
+ MEDIA_BUS_FMT_SGRBG8_1X8, MEDIA_BUS_FMT_SRGGB8_1X8,
+ MEDIA_BUS_FMT_SBGGR10_1X10, MEDIA_BUS_FMT_SGBRG10_1X10,
+ MEDIA_BUS_FMT_SGRBG10_1X10, MEDIA_BUS_FMT_SRGGB10_1X10,
+ MEDIA_BUS_FMT_SBGGR12_1X12, MEDIA_BUS_FMT_SGBRG12_1X12,
+ MEDIA_BUS_FMT_SGRBG12_1X12, MEDIA_BUS_FMT_SRGGB12_1X12,
+ MEDIA_BUS_FMT_UYVY8_1X16, MEDIA_BUS_FMT_BGR888_1X24
+};
+
+/* regulator supplies */
+static const char * const mipid02_supply_name[] = {
+ "VDDE", /* 1.8V digital I/O supply */
+ "VDDIN", /* 1V8 voltage regulator supply */
+};
+
+#define MIPID02_NUM_SUPPLIES ARRAY_SIZE(mipid02_supply_name)
+
+#define MIPID02_SINK_0 0
+#define MIPID02_SINK_1 1
+#define MIPID02_SOURCE 2
+#define MIPID02_PAD_NB 3
+
+struct mipid02_dev {
+ struct i2c_client *i2c_client;
+ struct regulator_bulk_data supplies[MIPID02_NUM_SUPPLIES];
+ struct v4l2_subdev sd;
+ struct media_pad pad[MIPID02_PAD_NB];
+ struct clk *xclk;
+ struct gpio_desc *reset_gpio;
+ /* endpoints info */
+ struct v4l2_fwnode_endpoint rx;
+ u64 link_frequency;
+ struct v4l2_fwnode_endpoint tx;
+ /* remote source */
+ struct v4l2_async_subdev asd;
+ struct v4l2_async_notifier notifier;
+ struct v4l2_subdev *s_subdev;
+ /* registers */
+ struct {
+ u8 clk_lane_reg1;
+ u8 data_lane0_reg1;
+ u8 data_lane1_reg1;
+ u8 mode_reg1;
+ u8 mode_reg2;
+ u8 data_id_rreg;
+ u8 pix_width_ctrl;
+ u8 pix_width_ctrl_emb;
+ } r;
+ /* lock to protect all members below */
+ struct mutex lock;
+ bool streaming;
+ struct v4l2_mbus_framefmt fmt;
+};
+
+static int bpp_from_code(__u32 code)
+{
+ switch (code) {
+ case MEDIA_BUS_FMT_SBGGR8_1X8:
+ case MEDIA_BUS_FMT_SGBRG8_1X8:
+ case MEDIA_BUS_FMT_SGRBG8_1X8:
+ case MEDIA_BUS_FMT_SRGGB8_1X8:
+ return 8;
+ case MEDIA_BUS_FMT_SBGGR10_1X10:
+ case MEDIA_BUS_FMT_SGBRG10_1X10:
+ case MEDIA_BUS_FMT_SGRBG10_1X10:
+ case MEDIA_BUS_FMT_SRGGB10_1X10:
+ return 10;
+ case MEDIA_BUS_FMT_SBGGR12_1X12:
+ case MEDIA_BUS_FMT_SGBRG12_1X12:
+ case MEDIA_BUS_FMT_SGRBG12_1X12:
+ case MEDIA_BUS_FMT_SRGGB12_1X12:
+ return 12;
+ case MEDIA_BUS_FMT_UYVY8_1X16:
+ return 16;
+ case MEDIA_BUS_FMT_BGR888_1X24:
+ return 24;
+ default:
+ return 0;
+ }
+}
+
+static u8 data_type_from_code(__u32 code)
+{
+ switch (code) {
+ case MEDIA_BUS_FMT_SBGGR8_1X8:
+ case MEDIA_BUS_FMT_SGBRG8_1X8:
+ case MEDIA_BUS_FMT_SGRBG8_1X8:
+ case MEDIA_BUS_FMT_SRGGB8_1X8:
+ return 0x2a;
+ case MEDIA_BUS_FMT_SBGGR10_1X10:
+ case MEDIA_BUS_FMT_SGBRG10_1X10:
+ case MEDIA_BUS_FMT_SGRBG10_1X10:
+ case MEDIA_BUS_FMT_SRGGB10_1X10:
+ return 0x2b;
+ case MEDIA_BUS_FMT_SBGGR12_1X12:
+ case MEDIA_BUS_FMT_SGBRG12_1X12:
+ case MEDIA_BUS_FMT_SGRBG12_1X12:
+ case MEDIA_BUS_FMT_SRGGB12_1X12:
+ return 0x2c;
+ case MEDIA_BUS_FMT_UYVY8_1X16:
+ return 0x1e;
+ case MEDIA_BUS_FMT_BGR888_1X24:
+ return 0x24;
+ default:
+ return 0;
+ }
+}
+
+static void init_format(struct v4l2_mbus_framefmt *fmt)
+{
+ fmt->code = MEDIA_BUS_FMT_SBGGR8_1X8;
+ fmt->field = V4L2_FIELD_NONE;
+ fmt->colorspace = V4L2_COLORSPACE_SRGB;
+ fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(V4L2_COLORSPACE_SRGB);
+ fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
+ fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(V4L2_COLORSPACE_SRGB);
+ fmt->width = 640;
+ fmt->height = 480;
+}
+
+static __u32 get_fmt_code(__u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(mipid02_supported_fmt_codes); i++) {
+ if (code == mipid02_supported_fmt_codes[i])
+ return code;
+ }
+
+ return mipid02_supported_fmt_codes[0];
+}
+
+static __u32 serial_to_parallel_code(__u32 serial)
+{
+ if (serial == MEDIA_BUS_FMT_UYVY8_1X16)
+ return MEDIA_BUS_FMT_UYVY8_2X8;
+ if (serial == MEDIA_BUS_FMT_BGR888_1X24)
+ return MEDIA_BUS_FMT_BGR888_3X8;
+
+ return serial;
+}
+
+static inline struct mipid02_dev *to_mipid02_dev(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct mipid02_dev, sd);
+}
+
+static int mipid02_read_reg(struct mipid02_dev *bridge, u16 reg, u8 *val)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ struct i2c_msg msg[2];
+ u8 buf[2];
+ int ret;
+
+ buf[0] = reg >> 8;
+ buf[1] = reg & 0xff;
+
+ msg[0].addr = client->addr;
+ msg[0].flags = client->flags;
+ msg[0].buf = buf;
+ msg[0].len = sizeof(buf);
+
+ msg[1].addr = client->addr;
+ msg[1].flags = client->flags | I2C_M_RD;
+ msg[1].buf = val;
+ msg[1].len = 1;
+
+ ret = i2c_transfer(client->adapter, msg, 2);
+ if (ret < 0) {
+ dev_dbg(&client->dev, "%s: %x i2c_transfer, reg: %x => %d\n",
+ __func__, client->addr, reg, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int mipid02_write_reg(struct mipid02_dev *bridge, u16 reg, u8 val)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ struct i2c_msg msg;
+ u8 buf[3];
+ int ret;
+
+ buf[0] = reg >> 8;
+ buf[1] = reg & 0xff;
+ buf[2] = val;
+
+ msg.addr = client->addr;
+ msg.flags = client->flags;
+ msg.buf = buf;
+ msg.len = sizeof(buf);
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ if (ret < 0) {
+ dev_dbg(&client->dev, "%s: i2c_transfer, reg: %x => %d\n",
+ __func__, reg, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int mipid02_get_regulators(struct mipid02_dev *bridge)
+{
+ unsigned int i;
+
+ for (i = 0; i < MIPID02_NUM_SUPPLIES; i++)
+ bridge->supplies[i].supply = mipid02_supply_name[i];
+
+ return devm_regulator_bulk_get(&bridge->i2c_client->dev,
+ MIPID02_NUM_SUPPLIES,
+ bridge->supplies);
+}
+
+static void mipid02_apply_reset(struct mipid02_dev *bridge)
+{
+ gpiod_set_value_cansleep(bridge->reset_gpio, 0);
+ usleep_range(5000, 10000);
+ gpiod_set_value_cansleep(bridge->reset_gpio, 1);
+ usleep_range(5000, 10000);
+ gpiod_set_value_cansleep(bridge->reset_gpio, 0);
+ usleep_range(5000, 10000);
+}
+
+static int mipid02_set_power_on(struct mipid02_dev *bridge)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ int ret;
+
+ ret = clk_prepare_enable(bridge->xclk);
+ if (ret) {
+ dev_err(&client->dev, "%s: failed to enable clock\n", __func__);
+ return ret;
+ }
+
+ ret = regulator_bulk_enable(MIPID02_NUM_SUPPLIES,
+ bridge->supplies);
+ if (ret) {
+ dev_err(&client->dev, "%s: failed to enable regulators\n",
+ __func__);
+ goto xclk_off;
+ }
+
+ if (bridge->reset_gpio) {
+ dev_dbg(&client->dev, "apply reset");
+ mipid02_apply_reset(bridge);
+ } else {
+ dev_dbg(&client->dev, "don't apply reset");
+ usleep_range(5000, 10000);
+ }
+
+ return 0;
+
+xclk_off:
+ clk_disable_unprepare(bridge->xclk);
+ return ret;
+}
+
+static void mipid02_set_power_off(struct mipid02_dev *bridge)
+{
+ regulator_bulk_disable(MIPID02_NUM_SUPPLIES, bridge->supplies);
+ clk_disable_unprepare(bridge->xclk);
+}
+
+static int mipid02_detect(struct mipid02_dev *bridge)
+{
+ u8 reg;
+
+ /*
+ * There is no version registers. Just try to read register
+ * MIPID02_CLK_LANE_WR_REG1.
+ */
+ return mipid02_read_reg(bridge, MIPID02_CLK_LANE_WR_REG1, ®);
+}
+
+static u32 mipid02_get_link_freq_from_cid_pixel_rate(struct mipid02_dev *bridge,
+ struct v4l2_subdev *subdev)
+{
+ struct v4l2_fwnode_endpoint *ep = &bridge->rx;
+ struct v4l2_ctrl *ctrl;
+ u32 pixel_clock;
+ u32 bpp = bpp_from_code(bridge->fmt.code);
+
+ ctrl = v4l2_ctrl_find(subdev->ctrl_handler, V4L2_CID_PIXEL_RATE);
+ if (!ctrl)
+ return 0;
+ pixel_clock = v4l2_ctrl_g_ctrl_int64(ctrl);
+
+ return pixel_clock * bpp / (2 * ep->bus.mipi_csi2.num_data_lanes);
+}
+
+/*
+ * We need to know link frequency to setup clk_lane_reg1 timings. Link frequency
+ * will be computed using connected device V4L2_CID_PIXEL_RATE, bit per pixel
+ * and number of lanes.
+ */
+static int mipid02_configure_from_rx_speed(struct mipid02_dev *bridge)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ struct v4l2_subdev *subdev = bridge->s_subdev;
+ u32 link_freq;
+
+ link_freq = mipid02_get_link_freq_from_cid_pixel_rate(bridge, subdev);
+ if (!link_freq) {
+ dev_err(&client->dev, "Failed to detect link frequency");
+ return -EINVAL;
+ }
+
+ dev_dbg(&client->dev, "detect link_freq = %d Hz", link_freq);
+ bridge->r.clk_lane_reg1 |= (2000000000 / link_freq) << 2;
+
+ return 0;
+}
+
+static int mipid02_configure_clk_lane(struct mipid02_dev *bridge)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ struct v4l2_fwnode_endpoint *ep = &bridge->rx;
+ bool *polarities = ep->bus.mipi_csi2.lane_polarities;
+
+ /* midid02 doesn't support clock lane remapping */
+ if (ep->bus.mipi_csi2.clock_lane != 0) {
+ dev_err(&client->dev, "clk lane must be map to lane 0\n");
+ return -EINVAL;
+ }
+ bridge->r.clk_lane_reg1 |= (polarities[0] << 1) | CLK_ENABLE;
+
+ return 0;
+}
+
+static int mipid02_configure_data0_lane(struct mipid02_dev *bridge, int nb,
+ bool are_lanes_swap, bool *polarities)
+{
+ bool are_pin_swap = are_lanes_swap ? polarities[2] : polarities[1];
+
+ if (nb == 1 && are_lanes_swap)
+ return 0;
+
+ /*
+ * data lane 0 as pin swap polarity reversed compared to clock and
+ * data lane 1
+ */
+ if (!are_pin_swap)
+ bridge->r.data_lane0_reg1 = 1 << 1;
+ bridge->r.data_lane0_reg1 |= DATA_ENABLE;
+
+ return 0;
+}
+
+static int mipid02_configure_data1_lane(struct mipid02_dev *bridge, int nb,
+ bool are_lanes_swap, bool *polarities)
+{
+ bool are_pin_swap = are_lanes_swap ? polarities[1] : polarities[2];
+
+ if (nb == 1 && !are_lanes_swap)
+ return 0;
+
+ if (are_pin_swap)
+ bridge->r.data_lane1_reg1 = 1 << 1;
+ bridge->r.data_lane1_reg1 |= DATA_ENABLE;
+
+ return 0;
+}
+
+static int mipid02_configure_from_rx(struct mipid02_dev *bridge)
+{
+ struct v4l2_fwnode_endpoint *ep = &bridge->rx;
+ bool are_lanes_swap = ep->bus.mipi_csi2.data_lanes[0] == 2;
+ bool *polarities = ep->bus.mipi_csi2.lane_polarities;
+ int nb = ep->bus.mipi_csi2.num_data_lanes;
+ int ret;
+
+ ret = mipid02_configure_clk_lane(bridge);
+ if (ret)
+ return ret;
+
+ ret = mipid02_configure_data0_lane(bridge, nb, are_lanes_swap,
+ polarities);
+ if (ret)
+ return ret;
+
+ ret = mipid02_configure_data1_lane(bridge, nb, are_lanes_swap,
+ polarities);
+ if (ret)
+ return ret;
+
+ bridge->r.mode_reg1 |= are_lanes_swap ? MODE_DATA_SWAP : 0;
+ bridge->r.mode_reg1 |= (nb - 1) << 1;
+
+ return mipid02_configure_from_rx_speed(bridge);
+}
+
+static int mipid02_configure_from_tx(struct mipid02_dev *bridge)
+{
+ struct v4l2_fwnode_endpoint *ep = &bridge->tx;
+
+ bridge->r.pix_width_ctrl = ep->bus.parallel.bus_width;
+ bridge->r.pix_width_ctrl_emb = ep->bus.parallel.bus_width;
+ if (ep->bus.parallel.flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
+ bridge->r.mode_reg2 |= MODE_HSYNC_ACTIVE_HIGH;
+ if (ep->bus.parallel.flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH)
+ bridge->r.mode_reg2 |= MODE_VSYNC_ACTIVE_HIGH;
+
+ return 0;
+}
+
+static int mipid02_configure_from_code(struct mipid02_dev *bridge)
+{
+ u8 data_type;
+
+ bridge->r.data_id_rreg = 0;
+ data_type = data_type_from_code(bridge->fmt.code);
+ if (!data_type)
+ return -EINVAL;
+ bridge->r.data_id_rreg = data_type;
+
+ return 0;
+}
+
+static int mipid02_stream_disable(struct mipid02_dev *bridge)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ int ret;
+
+ /* Disable all lanes */
+ ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG1, 0);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG1, 0);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG1, 0);
+ if (ret)
+ goto error;
+error:
+ if (ret)
+ dev_err(&client->dev, "failed to stream off %d", ret);
+
+ return ret;
+}
+
+static int mipid02_stream_enable(struct mipid02_dev *bridge)
+{
+ struct i2c_client *client = bridge->i2c_client;
+ int ret = -EINVAL;
+
+ if (!bridge->s_subdev)
+ goto error;
+
+ memset(&bridge->r, 0, sizeof(bridge->r));
+ /* build registers content */
+ ret = mipid02_configure_from_rx(bridge);
+ if (ret)
+ goto error;
+ ret = mipid02_configure_from_tx(bridge);
+ if (ret)
+ goto error;
+ ret = mipid02_configure_from_code(bridge);
+ if (ret)
+ goto error;
+
+ /* write mipi registers */
+ ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG1,
+ bridge->r.clk_lane_reg1);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_CLK_LANE_REG3, CLK_MIPI_CSI);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG1,
+ bridge->r.data_lane0_reg1);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE0_REG2,
+ DATA_MIPI_CSI);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG1,
+ bridge->r.data_lane1_reg1);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_LANE1_REG2,
+ DATA_MIPI_CSI);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_MODE_REG1,
+ MODE_NO_BYPASS | bridge->r.mode_reg1);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_MODE_REG2,
+ bridge->r.mode_reg2);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_ID_RREG,
+ bridge->r.data_id_rreg);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_DATA_SELECTION_CTRL,
+ SELECTION_MANUAL_DATA | SELECTION_MANUAL_WIDTH);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_PIX_WIDTH_CTRL,
+ bridge->r.pix_width_ctrl);
+ if (ret)
+ goto error;
+ ret = mipid02_write_reg(bridge, MIPID02_PIX_WIDTH_CTRL_EMB,
+ bridge->r.pix_width_ctrl_emb);
+ if (ret)
+ goto error;
+
+ return 0;
+
+error:
+ dev_err(&client->dev, "failed to stream on %d", ret);
+ mipid02_stream_disable(bridge);
+
+ return ret;
+}
+
+static int mipid02_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+ struct i2c_client *client = bridge->i2c_client;
+ int ret = 0;
+
+ dev_dbg(&client->dev, "%s : requested %d / current = %d", __func__,
+ enable, bridge->streaming);
+ mutex_lock(&bridge->lock);
+
+ if (bridge->streaming == enable)
+ goto out;
+
+ ret = enable ? mipid02_stream_enable(bridge) :
+ mipid02_stream_disable(bridge);
+ if (!ret)
+ bridge->streaming = enable;
+
+out:
+ dev_dbg(&client->dev, "%s current now = %d / %d", __func__,
+ bridge->streaming, ret);
+ mutex_unlock(&bridge->lock);
+
+ return ret;
+}
+
+static int mipid02_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+ int ret = 0;
+
+ switch (code->pad) {
+ case MIPID02_SINK_0:
+ if (code->index >= ARRAY_SIZE(mipid02_supported_fmt_codes))
+ ret = -EINVAL;
+ else
+ code->code = mipid02_supported_fmt_codes[code->index];
+ break;
+ case MIPID02_SOURCE:
+ if (code->index == 0)
+ code->code = serial_to_parallel_code(bridge->fmt.code);
+ else
+ ret = -EINVAL;
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ return ret;
+}
+
+static int mipid02_get_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct v4l2_mbus_framefmt *mbus_fmt = &format->format;
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+ struct i2c_client *client = bridge->i2c_client;
+ struct v4l2_mbus_framefmt *fmt;
+
+ dev_dbg(&client->dev, "%s probe %d", __func__, format->pad);
+
+ if (format->pad >= MIPID02_PAD_NB)
+ return -EINVAL;
+ /* second CSI-2 pad not yet supported */
+ if (format->pad == MIPID02_SINK_1)
+ return -EINVAL;
+
+ if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+ fmt = v4l2_subdev_get_try_format(&bridge->sd, cfg, format->pad);
+ else
+ fmt = &bridge->fmt;
+
+ mutex_lock(&bridge->lock);
+
+ *mbus_fmt = *fmt;
+ /* code may need to be converted for source */
+ if (format->pad == MIPID02_SOURCE)
+ mbus_fmt->code = serial_to_parallel_code(mbus_fmt->code);
+
+ mutex_unlock(&bridge->lock);
+
+ return 0;
+}
+
+static void mipid02_set_fmt_source(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+
+ /* source pad mirror active sink pad */
+ format->format = bridge->fmt;
+ /* but code may need to be converted */
+ format->format.code = serial_to_parallel_code(format->format.code);
+
+ /* only apply format for V4L2_SUBDEV_FORMAT_TRY case */
+ if (format->which != V4L2_SUBDEV_FORMAT_TRY)
+ return;
+
+ *v4l2_subdev_get_try_format(sd, cfg, format->pad) = format->format;
+}
+
+static void mipid02_set_fmt_sink(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+ struct v4l2_mbus_framefmt *fmt;
+
+ format->format.code = get_fmt_code(format->format.code);
+
+ if (format->which == V4L2_SUBDEV_FORMAT_TRY)
+ fmt = v4l2_subdev_get_try_format(sd, cfg, format->pad);
+ else
+ fmt = &bridge->fmt;
+
+ *fmt = format->format;
+}
+
+static int mipid02_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_pad_config *cfg,
+ struct v4l2_subdev_format *format)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+ struct i2c_client *client = bridge->i2c_client;
+ int ret = 0;
+
+ dev_dbg(&client->dev, "%s for %d", __func__, format->pad);
+
+ if (format->pad >= MIPID02_PAD_NB)
+ return -EINVAL;
+ /* second CSI-2 pad not yet supported */
+ if (format->pad == MIPID02_SINK_1)
+ return -EINVAL;
+
+ mutex_lock(&bridge->lock);
+
+ if (bridge->streaming) {
+ ret = -EBUSY;
+ goto error;
+ }
+
+ if (format->pad == MIPID02_SOURCE)
+ mipid02_set_fmt_source(sd, cfg, format);
+ else
+ mipid02_set_fmt_sink(sd, cfg, format);
+
+error:
+ mutex_unlock(&bridge->lock);
+
+ return ret;
+}
+
+static const struct v4l2_subdev_video_ops mipid02_video_ops = {
+ .s_stream = mipid02_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops mipid02_pad_ops = {
+ .enum_mbus_code = mipid02_enum_mbus_code,
+ .get_fmt = mipid02_get_fmt,
+ .set_fmt = mipid02_set_fmt,
+};
+
+static const struct v4l2_subdev_ops mipid02_subdev_ops = {
+ .video = &mipid02_video_ops,
+ .pad = &mipid02_pad_ops,
+};
+
+static const struct media_entity_operations mipid02_subdev_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+};
+
+static int mipid02_async_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *s_subdev,
+ struct v4l2_async_subdev *asd)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(notifier->sd);
+ struct i2c_client *client = bridge->i2c_client;
+ int source_pad;
+ int ret;
+
+ dev_dbg(&client->dev, "sensor_async_bound call %p", s_subdev);
+
+ source_pad = media_entity_get_fwnode_pad(&s_subdev->entity,
+ s_subdev->fwnode,
+ MEDIA_PAD_FL_SOURCE);
+ if (source_pad < 0) {
+ dev_err(&client->dev, "Couldn't find output pad for subdev %s\n",
+ s_subdev->name);
+ return source_pad;
+ }
+
+ ret = media_create_pad_link(&s_subdev->entity, source_pad,
+ &bridge->sd.entity, 0,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret) {
+ dev_err(&client->dev, "Couldn't create media link %d", ret);
+ return ret;
+ }
+
+ bridge->s_subdev = s_subdev;
+
+ return 0;
+}
+
+static void mipid02_async_unbind(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *s_subdev,
+ struct v4l2_async_subdev *asd)
+{
+ struct mipid02_dev *bridge = to_mipid02_dev(notifier->sd);
+
+ bridge->s_subdev = NULL;
+}
+
+static const struct v4l2_async_notifier_operations mipid02_notifier_ops = {
+ .bound = mipid02_async_bound,
+ .unbind = mipid02_async_unbind,
+};
+
+static int mipid02_parse_rx_ep(struct mipid02_dev *bridge)
+{
+ struct v4l2_fwnode_endpoint ep = { .bus_type = V4L2_MBUS_CSI2_DPHY };
+ struct i2c_client *client = bridge->i2c_client;
+ struct device_node *ep_node;
+ int ret;
+
+ /* parse rx (endpoint 0) */
+ ep_node = of_graph_get_endpoint_by_regs(bridge->i2c_client->dev.of_node,
+ 0, 0);
+ if (!ep_node) {
+ dev_err(&client->dev, "unable to find port0 ep");
+ ret = -EINVAL;
+ goto error;
+ }
+
+ ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), &ep);
+ if (ret) {
+ dev_err(&client->dev, "Could not parse v4l2 endpoint %d\n",
+ ret);
+ goto error_of_node_put;
+ }
+
+ /* do some sanity checks */
+ if (ep.bus.mipi_csi2.num_data_lanes > 2) {
+ dev_err(&client->dev, "max supported data lanes is 2 / got %d",
+ ep.bus.mipi_csi2.num_data_lanes);
+ ret = -EINVAL;
+ goto error_of_node_put;
+ }
+
+ /* register it for later use */
+ bridge->rx = ep;
+
+ /* register async notifier so we get noticed when sensor is connected */
+ bridge->asd.match.fwnode =
+ fwnode_graph_get_remote_port_parent(of_fwnode_handle(ep_node));
+ bridge->asd.match_type = V4L2_ASYNC_MATCH_FWNODE;
+ of_node_put(ep_node);
+
+ v4l2_async_notifier_init(&bridge->notifier);
+ ret = v4l2_async_notifier_add_subdev(&bridge->notifier, &bridge->asd);
+ if (ret) {
+ dev_err(&client->dev, "fail to register asd to notifier %d",
+ ret);
+ fwnode_handle_put(bridge->asd.match.fwnode);
+ return ret;
+ }
+ bridge->notifier.ops = &mipid02_notifier_ops;
+
+ ret = v4l2_async_subdev_notifier_register(&bridge->sd,
+ &bridge->notifier);
+ if (ret)
+ v4l2_async_notifier_cleanup(&bridge->notifier);
+
+ return ret;
+
+error_of_node_put:
+ of_node_put(ep_node);
+error:
+
+ return ret;
+}
+
+static int mipid02_parse_tx_ep(struct mipid02_dev *bridge)
+{
+ struct v4l2_fwnode_endpoint ep = { .bus_type = V4L2_MBUS_PARALLEL };
+ struct i2c_client *client = bridge->i2c_client;
+ struct device_node *ep_node;
+ int ret;
+
+ /* parse tx (endpoint 2) */
+ ep_node = of_graph_get_endpoint_by_regs(bridge->i2c_client->dev.of_node,
+ 2, 0);
+ if (!ep_node) {
+ dev_err(&client->dev, "unable to find port1 ep");
+ ret = -EINVAL;
+ goto error;
+ }
+
+ ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), &ep);
+ if (ret) {
+ dev_err(&client->dev, "Could not parse v4l2 endpoint\n");
+ goto error_of_node_put;
+ }
+
+ of_node_put(ep_node);
+ bridge->tx = ep;
+
+ return 0;
+
+error_of_node_put:
+ of_node_put(ep_node);
+error:
+
+ return -EINVAL;
+}
+
+static int mipid02_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct mipid02_dev *bridge;
+ u32 clk_freq;
+ int ret;
+
+ bridge = devm_kzalloc(dev, sizeof(*bridge), GFP_KERNEL);
+ if (!bridge)
+ return -ENOMEM;
+
+ init_format(&bridge->fmt);
+
+ bridge->i2c_client = client;
+ v4l2_i2c_subdev_init(&bridge->sd, client, &mipid02_subdev_ops);
+
+ /* got and check clock */
+ bridge->xclk = devm_clk_get(dev, "xclk");
+ if (IS_ERR(bridge->xclk)) {
+ dev_err(dev, "failed to get xclk\n");
+ return PTR_ERR(bridge->xclk);
+ }
+
+ clk_freq = clk_get_rate(bridge->xclk);
+ if (clk_freq < 6000000 || clk_freq > 27000000) {
+ dev_err(dev, "xclk freq must be in 6-27 Mhz range. got %d Hz\n",
+ clk_freq);
+ return -EINVAL;
+ }
+
+ bridge->reset_gpio = devm_gpiod_get_optional(dev, "reset",
+ GPIOD_OUT_HIGH);
+
+ ret = mipid02_get_regulators(bridge);
+ if (ret) {
+ dev_err(dev, "failed to get regulators %d", ret);
+ return ret;
+ }
+
+ mutex_init(&bridge->lock);
+ bridge->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ bridge->sd.entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+ bridge->sd.entity.ops = &mipid02_subdev_entity_ops;
+ bridge->pad[0].flags = MEDIA_PAD_FL_SINK;
+ bridge->pad[1].flags = MEDIA_PAD_FL_SINK;
+ bridge->pad[2].flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&bridge->sd.entity, MIPID02_PAD_NB,
+ bridge->pad);
+ if (ret) {
+ dev_err(&client->dev, "pads init failed %d", ret);
+ goto mutex_cleanup;
+ }
+
+ /* enable clock, power and reset device if available */
+ ret = mipid02_set_power_on(bridge);
+ if (ret)
+ goto entity_cleanup;
+
+ ret = mipid02_detect(bridge);
+ if (ret) {
+ dev_err(&client->dev, "failed to detect mipid02 %d", ret);
+ goto power_off;
+ }
+
+ ret = mipid02_parse_tx_ep(bridge);
+ if (ret) {
+ dev_err(&client->dev, "failed to parse tx %d", ret);
+ goto power_off;
+ }
+
+ ret = mipid02_parse_rx_ep(bridge);
+ if (ret) {
+ dev_err(&client->dev, "failed to parse rx %d", ret);
+ goto power_off;
+ }
+
+ ret = v4l2_async_register_subdev(&bridge->sd);
+ if (ret < 0) {
+ dev_err(&client->dev, "v4l2_async_register_subdev failed %d",
+ ret);
+ goto unregister_notifier;
+ }
+
+ dev_info(&client->dev, "mipid02 device probe successfully");
+
+ return 0;
+
+unregister_notifier:
+ v4l2_async_notifier_unregister(&bridge->notifier);
+ v4l2_async_notifier_cleanup(&bridge->notifier);
+power_off:
+ mipid02_set_power_off(bridge);
+entity_cleanup:
+ media_entity_cleanup(&bridge->sd.entity);
+mutex_cleanup:
+ mutex_destroy(&bridge->lock);
+
+ return ret;
+}
+
+static int mipid02_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct mipid02_dev *bridge = to_mipid02_dev(sd);
+
+ v4l2_async_notifier_unregister(&bridge->notifier);
+ v4l2_async_notifier_cleanup(&bridge->notifier);
+ v4l2_async_unregister_subdev(&bridge->sd);
+ mipid02_set_power_off(bridge);
+ media_entity_cleanup(&bridge->sd.entity);
+ mutex_destroy(&bridge->lock);
+
+ return 0;
+}
+
+static const struct of_device_id mipid02_dt_ids[] = {
+ { .compatible = "st,st-mipid02" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mipid02_dt_ids);
+
+static struct i2c_driver mipid02_i2c_driver = {
+ .driver = {
+ .name = "st-mipid02",
+ .of_match_table = mipid02_dt_ids,
+ },
+ .probe_new = mipid02_probe,
+ .remove = mipid02_remove,
+};
+
+module_i2c_driver(mipid02_i2c_driver);
+
+MODULE_AUTHOR("Mickael Guene <mickael.guene@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics MIPID02 CSI-2 bridge driver");
+MODULE_LICENSE("GPL v2");
projects / linux.git / commitdiff