What: /sys/devices/system/cpu/cpu*/cache/index3/cache_disable_{0,1}
Date: August 2008
KernelVersion: 2.6.27
-Contact: discuss@x86-64.org
+Contact: Linux kernel mailing list <linux-kernel@vger.kernel.org>
Description: Disable L3 cache indices
These files exist in every CPU's cache/index3 directory. Each
- #clock-cells: from common clock binding; shall be set to 1.
- clocks: from common clock binding; list of parent clock
handles, shall be xtal reference clock or xtal and clkin for
- si5351c only.
+ si5351c only. Corresponding clock input names are "xtal" and
+ "clkin" respectively.
- #address-cells: shall be set to 1.
- #size-cells: shall be set to 0.
/* connect xtal input to 25MHz reference */
clocks = <&ref25>;
+ clock-names = "xtal";
/* connect xtal input as source of pll0 and pll1 */
silabs,pll-source = <0 0>, <1 0>;
is not Linux-only, but in case of Linux, see the "m25p_ids"
table in drivers/mtd/devices/m25p80.c for the list of supported
chips.
- Must also include "nor-jedec" for any SPI NOR flash that can be
- identified by the JEDEC READ ID opcode (0x9F).
+ Must also include "jedec,spi-nor" for any SPI NOR flash that can
+ be identified by the JEDEC READ ID opcode (0x9F).
- reg : Chip-Select number
- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
flash: m25p80@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "spansion,m25p80", "nor-jedec";
+ compatible = "spansion,m25p80", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <40000000>;
m25p,fast-read;
Required properties:
- compatible: Should be "cdns,[<chip>-]{emac}"
Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
- or the generic form: "cdns,emac".
+ Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+ Or the generic form: "cdns,emac".
- reg: Address and length of the register set for the device
- interrupts: Should contain macb interrupt
- phy-mode: see ethernet.txt file in the same directory.
TTY_OTHER_CLOSED Device is a pty and the other side has closed.
+TTY_OTHER_DONE Device is a pty and the other side has closed and
+ all pending input processing has been completed.
+
TTY_NO_WRITE_SPLIT Prevent driver from splitting up writes into
smaller chunks.
Contains the value of cr4.smep && !cr0.wp for which the page is valid
(pages for which this is true are different from other pages; see the
treatment of cr0.wp=0 below).
+ role.smap_andnot_wp:
+ Contains the value of cr4.smap && !cr0.wp for which the page is valid
+ (pages for which this is true are different from other pages; see the
+ treatment of cr0.wp=0 below).
gfn:
Either the guest page table containing the translations shadowed by this
page, or the base page frame for linear translations. See role.direct.
(user write faults generate a #PF)
-In the first case there is an additional complication if CR4.SMEP is
-enabled: since we've turned the page into a kernel page, the kernel may now
-execute it. We handle this by also setting spte.nx. If we get a user
-fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back.
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+ the kernel may now execute it. We handle this by also setting spte.nx.
+ If we get a user fetch or read fault, we'll change spte.u=1 and
+ spte.nx=gpte.nx back.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+ page, it can not be reused when CR4.SMAP is enabled. We set
+ CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+ here we do not care the case that CR4.SMAP is enabled since KVM will
+ directly inject #PF to guest due to failed permission check.
To prevent an spte that was converted into a kernel page with cr0.wp=0
from being written by the kernel after cr0.wp has changed to 1, we make
ARM/CORTINA SYSTEMS GEMINI ARM ARCHITECTURE
M: Hans Ulli Kroll <ulli.kroll@googlemail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-T: git git://git.berlios.de/gemini-board
+T: git git://github.com/ulli-kroll/linux.git
S: Maintained
F: arch/arm/mach-gemini/
M: Philipp Zabel <philipp.zabel@gmail.com>
S: Maintained
-ARM/Marvell Armada 370 and Armada XP SOC support
+ARM/Marvell Kirkwood and Armada 370, 375, 38x, XP SOC support
M: Jason Cooper <jason@lakedaemon.net>
M: Andrew Lunn <andrew@lunn.ch>
M: Gregory Clement <gregory.clement@free-electrons.com>
S: Maintained
F: arch/arm/mach-mvebu/
F: drivers/rtc/rtc-armada38x.c
+F: arch/arm/boot/dts/armada*
+F: arch/arm/boot/dts/kirkwood*
+
ARM/Marvell Berlin SoC support
M: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-berlin/
+F: arch/arm/boot/dts/berlin*
+
ARM/Marvell Dove/MV78xx0/Orion SOC support
M: Jason Cooper <jason@lakedaemon.net>
F: arch/arm/mach-mv78xx0/
F: arch/arm/mach-orion5x/
F: arch/arm/plat-orion/
+F: arch/arm/boot/dts/dove*
+F: arch/arm/boot/dts/orion5x*
+
ARM/Orion SoC/Technologic Systems TS-78xx platform support
M: Alexander Clouter <alex@digriz.org.uk>
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES
M: Kukjin Kim <kgene@kernel.org>
+M: Krzysztof Kozlowski <k.kozlowski@samsung.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
S: Maintained
F: drivers/net/wireless/b43legacy/
BACKLIGHT CLASS/SUBSYSTEM
-M: Jingoo Han <jg1.han@samsung.com>
+M: Jingoo Han <jingoohan1@gmail.com>
M: Lee Jones <lee.jones@linaro.org>
S: Maintained
F: drivers/video/backlight/
L: linux-embedded@vger.kernel.org
S: Maintained
-EMULEX LPFC FC SCSI DRIVER
-M: James Smart <james.smart@emulex.com>
+EMULEX/AVAGO LPFC FC/FCOE SCSI DRIVER
+M: James Smart <james.smart@avagotech.com>
+M: Dick Kennedy <dick.kennedy@avagotech.com>
L: linux-scsi@vger.kernel.org
-W: http://sourceforge.net/projects/lpfcxxxx
+W: http://www.avagotech.com
S: Supported
F: drivers/scsi/lpfc/
F: Documentation/extcon/
EXYNOS DP DRIVER
-M: Jingoo Han <jg1.han@samsung.com>
+M: Jingoo Han <jingoohan1@gmail.com>
L: dri-devel@lists.freedesktop.org
S: Maintained
F: drivers/gpu/drm/exynos/exynos_dp*
F: include/uapi/linux/gfs2_ondisk.h
GIGASET ISDN DRIVERS
-M: Hansjoerg Lipp <hjlipp@web.de>
-M: Tilman Schmidt <tilman@imap.cc>
+M: Paul Bolle <pebolle@tiscali.nl>
L: gigaset307x-common@lists.sourceforge.net
W: http://gigaset307x.sourceforge.net/
-S: Maintained
+S: Odd Fixes
F: Documentation/isdn/README.gigaset
F: drivers/isdn/gigaset/
F: include/uapi/linux/gigaset_dev.h
M: Guenter Roeck <linux@roeck-us.net>
L: lm-sensors@lm-sensors.org
W: http://www.lm-sensors.org/
-T: quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-hwmon/
+T: quilt http://jdelvare.nerim.net/devel/linux/jdelvare-hwmon/
T: git git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging.git
S: Maintained
F: Documentation/hwmon/
L: linux-rdma@vger.kernel.org
W: http://www.openfabrics.org/
Q: http://patchwork.kernel.org/project/linux-rdma/list/
-T: git git://github.com/dledford/linux.git
+T: git git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma.git
S: Supported
F: Documentation/infiniband/
F: drivers/infiniband/
S: Maintained
F: arch/nios2/
+NOKIA N900 POWER SUPPLY DRIVERS
+M: Pali Rohár <pali.rohar@gmail.com>
+S: Maintained
+F: include/linux/power/bq2415x_charger.h
+F: include/linux/power/bq27x00_battery.h
+F: include/linux/power/isp1704_charger.h
+F: drivers/power/bq2415x_charger.c
+F: drivers/power/bq27x00_battery.c
+F: drivers/power/isp1704_charger.c
+F: drivers/power/rx51_battery.c
+
NTB DRIVER
M: Jon Mason <jdmason@kudzu.us>
M: Dave Jiang <dave.jiang@intel.com>
F: drivers/pci/host/*rcar*
PCI DRIVER FOR SAMSUNG EXYNOS
-M: Jingoo Han <jg1.han@samsung.com>
+M: Jingoo Han <jingoohan1@gmail.com>
L: linux-pci@vger.kernel.org
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
L: linux-samsung-soc@vger.kernel.org (moderated for non-subscribers)
F: drivers/pci/host/pci-exynos.c
PCI DRIVER FOR SYNOPSIS DESIGNWARE
-M: Jingoo Han <jg1.han@samsung.com>
+M: Jingoo Han <jingoohan1@gmail.com>
L: linux-pci@vger.kernel.org
S: Maintained
F: drivers/pci/host/*designware*
F: sound/soc/samsung/
SAMSUNG FRAMEBUFFER DRIVER
-M: Jingoo Han <jg1.han@samsung.com>
+M: Jingoo Han <jingoohan1@gmail.com>
L: linux-fbdev@vger.kernel.org
S: Maintained
F: drivers/video/fbdev/s3c-fb.c
F: include/uapi/linux/phantom.h
SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
-M: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
+M: Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
+M: Minh Tran <minh.tran@avagotech.com>
+M: John Soni Jose <sony.john-n@avagotech.com>
L: linux-scsi@vger.kernel.org
-W: http://www.emulex.com
+W: http://www.avagotech.com
S: Supported
F: drivers/scsi/be2iscsi/
-SERVER ENGINES 10Gbps NIC - BladeEngine 2 DRIVER
-M: Sathya Perla <sathya.perla@emulex.com>
-M: Subbu Seetharaman <subbu.seetharaman@emulex.com>
-M: Ajit Khaparde <ajit.khaparde@emulex.com>
+Emulex 10Gbps NIC BE2, BE3-R, Lancer, Skyhawk-R DRIVER
+M: Sathya Perla <sathya.perla@avagotech.com>
+M: Ajit Khaparde <ajit.khaparde@avagotech.com>
+M: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
+M: Sriharsha Basavapatna <sriharsha.basavapatna@avagotech.com>
L: netdev@vger.kernel.org
W: http://www.emulex.com
S: Supported
VERSION = 4
PATCHLEVEL = 1
SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc5
NAME = Hurr durr I'ma sheep
# *DOCUMENTATION*
tools/bootpzh bootloader bootpheader bootpzheader
OBJSTRIP := $(obj)/tools/objstrip
+HOSTCFLAGS := -Wall -I$(objtree)/usr/include
+BOOTCFLAGS += -I$(obj) -I$(srctree)/$(obj)
+
# SRM bootable image. Copy to offset 512 of a partition.
$(obj)/bootimage: $(addprefix $(obj)/tools/,mkbb lxboot bootlx) $(obj)/vmlinux.nh
( cat $(obj)/tools/lxboot $(obj)/tools/bootlx $(obj)/vmlinux.nh ) > $@
$(obj)/tools/bootpzh: $(obj)/bootpzheader $(OBJSTRIP) FORCE
$(call if_changed,objstrip)
-LDFLAGS_bootloader := -static -uvsprintf -T #-N -relax
-LDFLAGS_bootpheader := -static -uvsprintf -T #-N -relax
-LDFLAGS_bootpzheader := -static -uvsprintf -T #-N -relax
+LDFLAGS_bootloader := -static -T # -N -relax
+LDFLAGS_bootloader := -static -T # -N -relax
+LDFLAGS_bootpheader := -static -T # -N -relax
+LDFLAGS_bootpzheader := -static -T # -N -relax
-OBJ_bootlx := $(obj)/head.o $(obj)/main.o
-OBJ_bootph := $(obj)/head.o $(obj)/bootp.o
-OBJ_bootpzh := $(obj)/head.o $(obj)/bootpz.o $(obj)/misc.o
+OBJ_bootlx := $(obj)/head.o $(obj)/stdio.o $(obj)/main.o
+OBJ_bootph := $(obj)/head.o $(obj)/stdio.o $(obj)/bootp.o
+OBJ_bootpzh := $(obj)/head.o $(obj)/stdio.o $(obj)/bootpz.o $(obj)/misc.o
$(obj)/bootloader: $(obj)/bootloader.lds $(OBJ_bootlx) $(LIBS_Y) FORCE
$(call if_changed,ld)
#include "ksize.h"
-extern int vsprintf(char *, const char *, va_list);
extern unsigned long switch_to_osf_pal(unsigned long nr,
struct pcb_struct * pcb_va, struct pcb_struct * pcb_pa,
unsigned long *vptb);
--- /dev/null
+/*
+ * Copyright (C) Paul Mackerras 1997.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stdarg.h>
+#include <stddef.h>
+
+size_t strnlen(const char * s, size_t count)
+{
+ const char *sc;
+
+ for (sc = s; count-- && *sc != '\0'; ++sc)
+ /* nothing */;
+ return sc - s;
+}
+
+# define do_div(n, base) ({ \
+ unsigned int __base = (base); \
+ unsigned int __rem; \
+ __rem = ((unsigned long long)(n)) % __base; \
+ (n) = ((unsigned long long)(n)) / __base; \
+ __rem; \
+})
+
+
+static int skip_atoi(const char **s)
+{
+ int i, c;
+
+ for (i = 0; '0' <= (c = **s) && c <= '9'; ++*s)
+ i = i*10 + c - '0';
+ return i;
+}
+
+#define ZEROPAD 1 /* pad with zero */
+#define SIGN 2 /* unsigned/signed long */
+#define PLUS 4 /* show plus */
+#define SPACE 8 /* space if plus */
+#define LEFT 16 /* left justified */
+#define SPECIAL 32 /* 0x */
+#define LARGE 64 /* use 'ABCDEF' instead of 'abcdef' */
+
+static char * number(char * str, unsigned long long num, int base, int size, int precision, int type)
+{
+ char c,sign,tmp[66];
+ const char *digits="0123456789abcdefghijklmnopqrstuvwxyz";
+ int i;
+
+ if (type & LARGE)
+ digits = "0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ";
+ if (type & LEFT)
+ type &= ~ZEROPAD;
+ if (base < 2 || base > 36)
+ return 0;
+ c = (type & ZEROPAD) ? '0' : ' ';
+ sign = 0;
+ if (type & SIGN) {
+ if ((signed long long)num < 0) {
+ sign = '-';
+ num = - (signed long long)num;
+ size--;
+ } else if (type & PLUS) {
+ sign = '+';
+ size--;
+ } else if (type & SPACE) {
+ sign = ' ';
+ size--;
+ }
+ }
+ if (type & SPECIAL) {
+ if (base == 16)
+ size -= 2;
+ else if (base == 8)
+ size--;
+ }
+ i = 0;
+ if (num == 0)
+ tmp[i++]='0';
+ else while (num != 0) {
+ tmp[i++] = digits[do_div(num, base)];
+ }
+ if (i > precision)
+ precision = i;
+ size -= precision;
+ if (!(type&(ZEROPAD+LEFT)))
+ while(size-->0)
+ *str++ = ' ';
+ if (sign)
+ *str++ = sign;
+ if (type & SPECIAL) {
+ if (base==8)
+ *str++ = '0';
+ else if (base==16) {
+ *str++ = '0';
+ *str++ = digits[33];
+ }
+ }
+ if (!(type & LEFT))
+ while (size-- > 0)
+ *str++ = c;
+ while (i < precision--)
+ *str++ = '0';
+ while (i-- > 0)
+ *str++ = tmp[i];
+ while (size-- > 0)
+ *str++ = ' ';
+ return str;
+}
+
+int vsprintf(char *buf, const char *fmt, va_list args)
+{
+ int len;
+ unsigned long long num;
+ int i, base;
+ char * str;
+ const char *s;
+
+ int flags; /* flags to number() */
+
+ int field_width; /* width of output field */
+ int precision; /* min. # of digits for integers; max
+ number of chars for from string */
+ int qualifier; /* 'h', 'l', or 'L' for integer fields */
+ /* 'z' support added 23/7/1999 S.H. */
+ /* 'z' changed to 'Z' --davidm 1/25/99 */
+
+
+ for (str=buf ; *fmt ; ++fmt) {
+ if (*fmt != '%') {
+ *str++ = *fmt;
+ continue;
+ }
+
+ /* process flags */
+ flags = 0;
+ repeat:
+ ++fmt; /* this also skips first '%' */
+ switch (*fmt) {
+ case '-': flags |= LEFT; goto repeat;
+ case '+': flags |= PLUS; goto repeat;
+ case ' ': flags |= SPACE; goto repeat;
+ case '#': flags |= SPECIAL; goto repeat;
+ case '0': flags |= ZEROPAD; goto repeat;
+ }
+
+ /* get field width */
+ field_width = -1;
+ if ('0' <= *fmt && *fmt <= '9')
+ field_width = skip_atoi(&fmt);
+ else if (*fmt == '*') {
+ ++fmt;
+ /* it's the next argument */
+ field_width = va_arg(args, int);
+ if (field_width < 0) {
+ field_width = -field_width;
+ flags |= LEFT;
+ }
+ }
+
+ /* get the precision */
+ precision = -1;
+ if (*fmt == '.') {
+ ++fmt;
+ if ('0' <= *fmt && *fmt <= '9')
+ precision = skip_atoi(&fmt);
+ else if (*fmt == '*') {
+ ++fmt;
+ /* it's the next argument */
+ precision = va_arg(args, int);
+ }
+ if (precision < 0)
+ precision = 0;
+ }
+
+ /* get the conversion qualifier */
+ qualifier = -1;
+ if (*fmt == 'l' && *(fmt + 1) == 'l') {
+ qualifier = 'q';
+ fmt += 2;
+ } else if (*fmt == 'h' || *fmt == 'l' || *fmt == 'L'
+ || *fmt == 'Z') {
+ qualifier = *fmt;
+ ++fmt;
+ }
+
+ /* default base */
+ base = 10;
+
+ switch (*fmt) {
+ case 'c':
+ if (!(flags & LEFT))
+ while (--field_width > 0)
+ *str++ = ' ';
+ *str++ = (unsigned char) va_arg(args, int);
+ while (--field_width > 0)
+ *str++ = ' ';
+ continue;
+
+ case 's':
+ s = va_arg(args, char *);
+ if (!s)
+ s = "<NULL>";
+
+ len = strnlen(s, precision);
+
+ if (!(flags & LEFT))
+ while (len < field_width--)
+ *str++ = ' ';
+ for (i = 0; i < len; ++i)
+ *str++ = *s++;
+ while (len < field_width--)
+ *str++ = ' ';
+ continue;
+
+ case 'p':
+ if (field_width == -1) {
+ field_width = 2*sizeof(void *);
+ flags |= ZEROPAD;
+ }
+ str = number(str,
+ (unsigned long) va_arg(args, void *), 16,
+ field_width, precision, flags);
+ continue;
+
+
+ case 'n':
+ if (qualifier == 'l') {
+ long * ip = va_arg(args, long *);
+ *ip = (str - buf);
+ } else if (qualifier == 'Z') {
+ size_t * ip = va_arg(args, size_t *);
+ *ip = (str - buf);
+ } else {
+ int * ip = va_arg(args, int *);
+ *ip = (str - buf);
+ }
+ continue;
+
+ case '%':
+ *str++ = '%';
+ continue;
+
+ /* integer number formats - set up the flags and "break" */
+ case 'o':
+ base = 8;
+ break;
+
+ case 'X':
+ flags |= LARGE;
+ case 'x':
+ base = 16;
+ break;
+
+ case 'd':
+ case 'i':
+ flags |= SIGN;
+ case 'u':
+ break;
+
+ default:
+ *str++ = '%';
+ if (*fmt)
+ *str++ = *fmt;
+ else
+ --fmt;
+ continue;
+ }
+ if (qualifier == 'l') {
+ num = va_arg(args, unsigned long);
+ if (flags & SIGN)
+ num = (signed long) num;
+ } else if (qualifier == 'q') {
+ num = va_arg(args, unsigned long long);
+ if (flags & SIGN)
+ num = (signed long long) num;
+ } else if (qualifier == 'Z') {
+ num = va_arg(args, size_t);
+ } else if (qualifier == 'h') {
+ num = (unsigned short) va_arg(args, int);
+ if (flags & SIGN)
+ num = (signed short) num;
+ } else {
+ num = va_arg(args, unsigned int);
+ if (flags & SIGN)
+ num = (signed int) num;
+ }
+ str = number(str, num, base, field_width, precision, flags);
+ }
+ *str = '\0';
+ return str-buf;
+}
+
+int sprintf(char * buf, const char *fmt, ...)
+{
+ va_list args;
+ int i;
+
+ va_start(args, fmt);
+ i=vsprintf(buf,fmt,args);
+ va_end(args);
+ return i;
+}
#include <linux/param.h>
#ifdef __ELF__
# include <linux/elf.h>
+# define elfhdr elf64_hdr
+# define elf_phdr elf64_phdr
+# define elf_check_arch(x) ((x)->e_machine == EM_ALPHA)
#endif
/* bootfile size must be multiple of BLOCK_SIZE: */
#define _ALPHA_TYPES_H
#include <asm-generic/int-ll64.h>
-#include <uapi/asm/types.h>
#endif /* _ALPHA_TYPES_H */
#include <uapi/asm/unistd.h>
-#define NR_SYSCALLS 511
+#define NR_SYSCALLS 514
#define __ARCH_WANT_OLD_READDIR
#define __ARCH_WANT_STAT64
#define __NR_sched_setattr 508
#define __NR_sched_getattr 509
#define __NR_renameat2 510
+#define __NR_getrandom 511
+#define __NR_memfd_create 512
+#define __NR_execveat 513
#endif /* _UAPI_ALPHA_UNISTD_H */
* Error handling code supporting Alpha systems
*/
-#include <linux/init.h>
#include <linux/sched.h>
#include <asm/io.h>
#include <linux/ptrace.h>
#include <linux/interrupt.h>
#include <linux/random.h>
-#include <linux/init.h>
#include <linux/irq.h>
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
if (tv) {
if (get_tv32((struct timeval *)&kts, tv))
return -EFAULT;
+ kts.tv_nsec *= 1000;
}
if (tz) {
if (copy_from_user(&ktz, tz, sizeof(*tz)))
return -EFAULT;
}
- kts.tv_nsec *= 1000;
-
return do_sys_settimeofday(tv ? &kts : NULL, tz ? &ktz : NULL);
}
}
/*
- * Copy an alpha thread..
+ * Copy architecture-specific thread state
*/
-
int
copy_thread(unsigned long clone_flags, unsigned long usp,
- unsigned long arg,
+ unsigned long kthread_arg,
struct task_struct *p)
{
extern void ret_from_fork(void);
sizeof(struct switch_stack) + sizeof(struct pt_regs));
childstack->r26 = (unsigned long) ret_from_kernel_thread;
childstack->r9 = usp; /* function */
- childstack->r10 = arg;
+ childstack->r10 = kthread_arg;
childregs->hae = alpha_mv.hae_cache,
childti->pcb.usp = 0;
return 0;
enum ipi_message_type {
IPI_RESCHEDULE,
IPI_CALL_FUNC,
- IPI_CALL_FUNC_SINGLE,
IPI_CPU_STOP,
};
return -EINVAL;
}
-\f
static void
send_ipi_message(const struct cpumask *to_whom, enum ipi_message_type operation)
{
generic_smp_call_function_interrupt();
break;
- case IPI_CALL_FUNC_SINGLE:
- generic_smp_call_function_single_interrupt();
- break;
-
case IPI_CPU_STOP:
halt();
void arch_send_call_function_single_ipi(int cpu)
{
- send_ipi_message(cpumask_of(cpu), IPI_CALL_FUNC_SINGLE);
+ send_ipi_message(cpumask_of(cpu), IPI_CALL_FUNC);
}
static void
return -ENODEV;
}
-
-module_init(srmcons_init);
+device_initcall(srmcons_init);
\f
/*
pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &intline);
irq = intline;
- msi_loc = pci_find_capability(dev, PCI_CAP_ID_MSI);
+ msi_loc = dev->msi_cap;
msg_ctl = 0;
if (msi_loc)
pci_read_config_word(dev, msi_loc + PCI_MSI_FLAGS, &msg_ctl);
.quad sys_sched_setattr
.quad sys_sched_getattr
.quad sys_renameat2 /* 510 */
+ .quad sys_getrandom
+ .quad sys_memfd_create
+ .quad sys_execveat
.size sys_call_table, . - sys_call_table
.type sys_call_table, @object
#include <linux/tty.h>
#include <linux/delay.h>
#include <linux/module.h>
-#include <linux/init.h>
#include <linux/kallsyms.h>
#include <linux/ratelimit.h>
*/
#include <linux/oprofile.h>
-#include <linux/init.h>
#include <linux/smp.h>
#include <asm/ptrace.h>
*/
#include <linux/oprofile.h>
-#include <linux/init.h>
#include <linux/smp.h>
#include <asm/ptrace.h>
*/
#include <linux/oprofile.h>
-#include <linux/init.h>
#include <linux/smp.h>
#include <asm/ptrace.h>
*/
#include <linux/oprofile.h>
-#include <linux/init.h>
#include <linux/smp.h>
#include <asm/ptrace.h>
source "lib/Kconfig.debug"
-config EARLY_PRINTK
- bool "Early printk" if EMBEDDED
- default y
- help
- Write kernel log output directly into the VGA buffer or to a serial
- port.
-
- This is useful for kernel debugging when your machine crashes very
- early before the console code is initialized. For normal operation
- it is not recommended because it looks ugly and doesn't cooperate
- with klogd/syslogd or the X server. You should normally N here,
- unless you want to debug such a crash.
-
config 16KSTACKS
bool "Use 16Kb for kernel stacks instead of 8Kb"
help
atomic_ops_unlock(flags); \
}
-#define ATOMIC_OP_RETURN(op, c_op) \
+#define ATOMIC_OP_RETURN(op, c_op, asm_op) \
static inline int atomic_##op##_return(int i, atomic_t *v) \
{ \
unsigned long flags; \
* Machine specific helpers for Entire D-Cache or Per Line ops
*/
-static unsigned int __before_dc_op(const int op)
+static inline unsigned int __before_dc_op(const int op)
{
unsigned int reg = reg;
return reg;
}
-static void __after_dc_op(const int op, unsigned int reg)
+static inline void __after_dc_op(const int op, unsigned int reg)
{
if (op & OP_FLUSH) /* flush / flush-n-inv both wait */
while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS);
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <2000000000>;
+ clock-frequency = <1000000000>;
};
/* 25 MHz reference crystal */
refclk: oscillator {
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <2000000000>;
+ clock-frequency = <1000000000>;
};
/* 25 MHz reference crystal */
mainpll: mainpll {
compatible = "fixed-clock";
#clock-cells = <0>;
- clock-frequency = <2000000000>;
+ clock-frequency = <1000000000>;
};
};
};
/* connect xtal input to 25MHz reference */
clocks = <&ref25>;
+ clock-names = "xtal";
/* connect xtal input as source of pll0 and pll1 */
silabs,pll-source = <0 0>, <1 0>;
num-slots = <1>;
broken-cd;
cap-sdio-irq;
+ keep-power-in-suspend;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <1>;
num-slots = <1>;
broken-cd;
cap-sdio-irq;
+ keep-power-in-suspend;
card-detect-delay = <200>;
clock-frequency = <400000000>;
samsung,dw-mshc-ciu-div = <1>;
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
- resets = <&tegra_car 59>, <&tegra_car 22>;
+ resets = <&tegra_car 22>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
nvidia,hssquelch-level = <2>;
nvidia,hsdiscon-level = <5>;
nvidia,xcvr-hsslew = <12>;
+ nvidia,has-utmi-pad-registers;
status = "disabled";
};
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
- resets = <&tegra_car 22>, <&tegra_car 22>;
+ resets = <&tegra_car 58>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
nvidia,hssquelch-level = <2>;
nvidia,hsdiscon-level = <5>;
nvidia,xcvr-hsslew = <12>;
- nvidia,has-utmi-pad-registers;
status = "disabled";
};
<&tegra_car TEGRA124_CLK_PLL_U>,
<&tegra_car TEGRA124_CLK_USBD>;
clock-names = "reg", "pll_u", "utmi-pads";
- resets = <&tegra_car 58>, <&tegra_car 22>;
+ resets = <&tegra_car 59>, <&tegra_car 22>;
reset-names = "usb", "utmi-pads";
nvidia,hssync-start-delay = <0>;
nvidia,idle-wait-delay = <17>;
compatible = "arm,cortex-a15-pmu";
interrupts = <0 68 4>,
<0 69 4>;
+ interrupt-affinity = <&cpu0>, <&cpu1>;
};
oscclk6a: oscclk6a {
#address-cells = <1>;
#size-cells = <0>;
- cpu@0 {
+ A9_0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <0>;
next-level-cache = <&L2>;
};
- cpu@1 {
+ A9_1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <1>;
next-level-cache = <&L2>;
};
- cpu@2 {
+ A9_2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <2>;
next-level-cache = <&L2>;
};
- cpu@3 {
+ A9_3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a9";
reg = <3>;
compatible = "arm,pl310-cache";
reg = <0x1e00a000 0x1000>;
interrupts = <0 43 4>;
+ cache-unified;
cache-level = <2>;
arm,data-latency = <1 1 1>;
arm,tag-latency = <1 1 1>;
<0 61 4>,
<0 62 4>,
<0 63 4>;
+ interrupt-affinity = <&A9_0>, <&A9_1>, <&A9_2>, <&A9_3>;
+
};
dcc {
};
gem0: ethernet@e000b000 {
- compatible = "cdns,gem";
+ compatible = "cdns,zynq-gem";
reg = <0xe000b000 0x1000>;
status = "disabled";
interrupts = <0 22 4>;
};
gem1: ethernet@e000c000 {
- compatible = "cdns,gem";
+ compatible = "cdns,zynq-gem";
reg = <0xe000c000 0x1000>;
status = "disabled";
interrupts = <0 45 4>;
extern struct cpuidle_exynos_data cpuidle_coupled_exynos_data;
+extern void exynos_set_delayed_reset_assertion(bool enable);
+
extern void s5p_init_cpu(void __iomem *cpuid_addr);
extern unsigned int samsung_rev(void);
extern void __iomem *cpu_boot_reg_base(void);
exynos_map_io();
}
+/*
+ * Set or clear the USE_DELAYED_RESET_ASSERTION option. Used by smp code
+ * and suspend.
+ *
+ * This is necessary only on Exynos4 SoCs. When system is running
+ * USE_DELAYED_RESET_ASSERTION should be set so the ARM CLK clock down
+ * feature could properly detect global idle state when secondary CPU is
+ * powered down.
+ *
+ * However this should not be set when such system is going into suspend.
+ */
+void exynos_set_delayed_reset_assertion(bool enable)
+{
+ if (of_machine_is_compatible("samsung,exynos4")) {
+ unsigned int tmp, core_id;
+
+ for (core_id = 0; core_id < num_possible_cpus(); core_id++) {
+ tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
+ if (enable)
+ tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
+ else
+ tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
+ pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
+ }
+ }
+}
+
/*
* Apparently, these SoCs are not able to wake-up from suspend using
* the PMU. Too bad. Should they suddenly become capable of such a
extern void exynos4_secondary_startup(void);
-/*
- * Set or clear the USE_DELAYED_RESET_ASSERTION option, set on Exynos4 SoCs
- * during hot-(un)plugging CPUx.
- *
- * The feature can be cleared safely during first boot of secondary CPU.
- *
- * Exynos4 SoCs require setting USE_DELAYED_RESET_ASSERTION during powering
- * down a CPU so the CPU idle clock down feature could properly detect global
- * idle state when CPUx is off.
- */
-static void exynos_set_delayed_reset_assertion(u32 core_id, bool enable)
-{
- if (soc_is_exynos4()) {
- unsigned int tmp;
-
- tmp = pmu_raw_readl(EXYNOS_ARM_CORE_OPTION(core_id));
- if (enable)
- tmp |= S5P_USE_DELAYED_RESET_ASSERTION;
- else
- tmp &= ~(S5P_USE_DELAYED_RESET_ASSERTION);
- pmu_raw_writel(tmp, EXYNOS_ARM_CORE_OPTION(core_id));
- }
-}
-
#ifdef CONFIG_HOTPLUG_CPU
static inline void cpu_leave_lowpower(u32 core_id)
{
: "=&r" (v)
: "Ir" (CR_C), "Ir" (0x40)
: "cc");
-
- exynos_set_delayed_reset_assertion(core_id, false);
}
static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
/* Turn the CPU off on next WFI instruction. */
exynos_cpu_power_down(core_id);
- /*
- * Exynos4 SoCs require setting
- * USE_DELAYED_RESET_ASSERTION so the CPU idle
- * clock down feature could properly detect
- * global idle state when CPUx is off.
- */
- exynos_set_delayed_reset_assertion(core_id, true);
-
wfi();
if (pen_release == core_id) {
udelay(10);
}
- /* No harm if this is called during first boot of secondary CPU */
- exynos_set_delayed_reset_assertion(core_id, false);
-
/*
* now the secondary core is starting up let it run its
* calibrations, then wait for it to finish
exynos_sysram_init();
+ exynos_set_delayed_reset_assertion(true);
+
if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9)
scu_enable(scu_base_addr());
args.np = np;
args.args_count = 0;
child_domain = of_genpd_get_from_provider(&args);
- if (!child_domain)
+ if (IS_ERR(child_domain))
continue;
if (of_parse_phandle_with_args(np, "power-domains",
continue;
parent_domain = of_genpd_get_from_provider(&args);
- if (!parent_domain)
+ if (IS_ERR(parent_domain))
continue;
if (pm_genpd_add_subdomain(parent_domain, child_domain))
static void exynos_pm_prepare(void)
{
+ exynos_set_delayed_reset_assertion(false);
+
/* Set wake-up mask registers */
exynos_pm_set_wakeup_mask();
/* Clear SLEEP mode set in INFORM1 */
pmu_raw_writel(0x0, S5P_INFORM1);
+ exynos_set_delayed_reset_assertion(true);
}
static void exynos3250_pm_resume(void)
return;
}
- if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL)))
+ if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) {
pr_warn("Outdated DT detected, suspend/resume will NOT work\n");
+ return;
+ }
pm_data = (const struct exynos_pm_data *) match->data;
#ifndef __GEMINI_COMMON_H__
#define __GEMINI_COMMON_H__
+#include <linux/reboot.h>
+
struct mtd_partition;
extern void gemini_map_io(void);
struct mtd_partition *parts,
unsigned int nr_parts);
-extern void gemini_restart(char mode, const char *cmd);
+extern void gemini_restart(enum reboot_mode mode, const char *cmd);
#endif /* __GEMINI_COMMON_H__ */
#include <mach/hardware.h>
#include <mach/global_reg.h>
-void gemini_restart(char mode, const char *cmd)
+#include "common.h"
+
+void gemini_restart(enum reboot_mode mode, const char *cmd)
{
__raw_writel(RESET_GLOBAL | RESET_CPU1,
IO_ADDRESS(GEMINI_GLOBAL_BASE) + GLOBAL_RESET);
*/
#define LINKS_PER_OCP_IF 2
+/*
+ * Address offset (in bytes) between the reset control and the reset
+ * status registers: 4 bytes on OMAP4
+ */
+#define OMAP4_RST_CTRL_ST_OFFSET 4
+
/**
* struct omap_hwmod_soc_ops - fn ptrs for some SoC-specific operations
* @enable_module: function to enable a module (via MODULEMODE)
if (ohri->st_shift)
pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
oh->name, ohri->name);
- return omap_prm_deassert_hardreset(ohri->rst_shift, 0,
+ return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->rst_shift,
oh->clkdm->pwrdm.ptr->prcm_partition,
oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs, 0);
+ oh->prcm.omap4.rstctrl_offs,
+ oh->prcm.omap4.rstctrl_offs +
+ OMAP4_RST_CTRL_ST_OFFSET);
}
/**
oh->prcm.omap4.rstctrl_offs);
}
-/**
- * _am33xx_assert_hardreset - call AM33XX PRM hardreset fn with hwmod args
- * @oh: struct omap_hwmod * to assert hardreset
- * @ohri: hardreset line data
- *
- * Call am33xx_prminst_assert_hardreset() with parameters extracted
- * from the hwmod @oh and the hardreset line data @ohri. Only
- * intended for use as an soc_ops function pointer. Passes along the
- * return value from am33xx_prminst_assert_hardreset(). XXX This
- * function is scheduled for removal when the PRM code is moved into
- * drivers/.
- */
-static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
- struct omap_hwmod_rst_info *ohri)
-
-{
- return omap_prm_assert_hardreset(ohri->rst_shift, 0,
- oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs);
-}
-
/**
* _am33xx_deassert_hardreset - call AM33XX PRM hardreset fn with hwmod args
* @oh: struct omap_hwmod * to deassert hardreset
static int _am33xx_deassert_hardreset(struct omap_hwmod *oh,
struct omap_hwmod_rst_info *ohri)
{
- return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift, 0,
+ return omap_prm_deassert_hardreset(ohri->rst_shift, ohri->st_shift,
+ oh->clkdm->pwrdm.ptr->prcm_partition,
oh->clkdm->pwrdm.ptr->prcm_offs,
oh->prcm.omap4.rstctrl_offs,
oh->prcm.omap4.rstst_offs);
}
-/**
- * _am33xx_is_hardreset_asserted - call AM33XX PRM hardreset fn with hwmod args
- * @oh: struct omap_hwmod * to test hardreset
- * @ohri: hardreset line data
- *
- * Call am33xx_prminst_is_hardreset_asserted() with parameters
- * extracted from the hwmod @oh and the hardreset line data @ohri.
- * Only intended for use as an soc_ops function pointer. Passes along
- * the return value from am33xx_prminst_is_hardreset_asserted(). XXX
- * This function is scheduled for removal when the PRM code is moved
- * into drivers/.
- */
-static int _am33xx_is_hardreset_asserted(struct omap_hwmod *oh,
- struct omap_hwmod_rst_info *ohri)
-{
- return omap_prm_is_hardreset_asserted(ohri->rst_shift, 0,
- oh->clkdm->pwrdm.ptr->prcm_offs,
- oh->prcm.omap4.rstctrl_offs);
-}
-
/* Public functions */
u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs)
soc_ops.init_clkdm = _init_clkdm;
soc_ops.update_context_lost = _omap4_update_context_lost;
soc_ops.get_context_lost = _omap4_get_context_lost;
- } else if (soc_is_am43xx()) {
+ } else if (cpu_is_ti816x() || soc_is_am33xx() || soc_is_am43xx()) {
soc_ops.enable_module = _omap4_enable_module;
soc_ops.disable_module = _omap4_disable_module;
soc_ops.wait_target_ready = _omap4_wait_target_ready;
soc_ops.assert_hardreset = _omap4_assert_hardreset;
- soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
- soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
- soc_ops.init_clkdm = _init_clkdm;
- } else if (cpu_is_ti816x() || soc_is_am33xx()) {
- soc_ops.enable_module = _omap4_enable_module;
- soc_ops.disable_module = _omap4_disable_module;
- soc_ops.wait_target_ready = _omap4_wait_target_ready;
- soc_ops.assert_hardreset = _am33xx_assert_hardreset;
soc_ops.deassert_hardreset = _am33xx_deassert_hardreset;
- soc_ops.is_hardreset_asserted = _am33xx_is_hardreset_asserted;
+ soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
soc_ops.init_clkdm = _init_clkdm;
} else {
WARN(1, "omap_hwmod: unknown SoC type\n");
},
};
+static struct omap_hwmod_class_sysconfig am43xx_vpfe_sysc = {
+ .rev_offs = 0x0,
+ .sysc_offs = 0x104,
+ .sysc_flags = SYSC_HAS_MIDLEMODE | SYSC_HAS_SIDLEMODE,
+ .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+ MSTANDBY_FORCE | MSTANDBY_SMART | MSTANDBY_NO),
+ .sysc_fields = &omap_hwmod_sysc_type2,
+};
+
+static struct omap_hwmod_class am43xx_vpfe_hwmod_class = {
+ .name = "vpfe",
+ .sysc = &am43xx_vpfe_sysc,
+};
+
+static struct omap_hwmod am43xx_vpfe0_hwmod = {
+ .name = "vpfe0",
+ .class = &am43xx_vpfe_hwmod_class,
+ .clkdm_name = "l3s_clkdm",
+ .prcm = {
+ .omap4 = {
+ .modulemode = MODULEMODE_SWCTRL,
+ .clkctrl_offs = AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET,
+ },
+ },
+};
+
+static struct omap_hwmod am43xx_vpfe1_hwmod = {
+ .name = "vpfe1",
+ .class = &am43xx_vpfe_hwmod_class,
+ .clkdm_name = "l3s_clkdm",
+ .prcm = {
+ .omap4 = {
+ .modulemode = MODULEMODE_SWCTRL,
+ .clkctrl_offs = AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET,
+ },
+ },
+};
+
/* Interfaces */
static struct omap_hwmod_ocp_if am43xx_l3_main__l4_hs = {
.master = &am33xx_l3_main_hwmod,
.user = OCP_USER_MPU | OCP_USER_SDMA,
};
+static struct omap_hwmod_ocp_if am43xx_l3__vpfe0 = {
+ .master = &am43xx_vpfe0_hwmod,
+ .slave = &am33xx_l3_main_hwmod,
+ .clk = "l3_gclk",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l3__vpfe1 = {
+ .master = &am43xx_vpfe1_hwmod,
+ .slave = &am33xx_l3_main_hwmod,
+ .clk = "l3_gclk",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe0 = {
+ .master = &am33xx_l4_ls_hwmod,
+ .slave = &am43xx_vpfe0_hwmod,
+ .clk = "l4ls_gclk",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+static struct omap_hwmod_ocp_if am43xx_l4_ls__vpfe1 = {
+ .master = &am33xx_l4_ls_hwmod,
+ .slave = &am43xx_vpfe1_hwmod,
+ .clk = "l4ls_gclk",
+ .user = OCP_USER_MPU | OCP_USER_SDMA,
+};
+
static struct omap_hwmod_ocp_if *am43xx_hwmod_ocp_ifs[] __initdata = {
&am33xx_l4_wkup__synctimer,
&am43xx_l4_ls__timer8,
&am43xx_l4_ls__dss_dispc,
&am43xx_l4_ls__dss_rfbi,
&am43xx_l4_ls__hdq1w,
+ &am43xx_l3__vpfe0,
+ &am43xx_l3__vpfe1,
+ &am43xx_l4_ls__vpfe0,
+ &am43xx_l4_ls__vpfe1,
NULL,
};
#define AM43XX_CM_PER_USBPHYOCP2SCP1_CLKCTRL_OFFSET 0x05C0
#define AM43XX_CM_PER_DSS_CLKCTRL_OFFSET 0x0a20
#define AM43XX_CM_PER_HDQ1W_CLKCTRL_OFFSET 0x04a0
-
+#define AM43XX_CM_PER_VPFE0_CLKCTRL_OFFSET 0x0068
+#define AM43XX_CM_PER_VPFE1_CLKCTRL_OFFSET 0x0070
#endif
return v;
}
-/*
- * Address offset (in bytes) between the reset control and the reset
- * status registers: 4 bytes on OMAP4
- */
-#define OMAP4_RST_CTRL_ST_OFFSET 4
-
/**
* omap4_prminst_is_hardreset_asserted - read the HW reset line state of
* submodules contained in the hwmod module
* omap4_prminst_deassert_hardreset - deassert a submodule hardreset line and
* wait
* @shift: register bit shift corresponding to the reset line to deassert
- * @st_shift: status bit offset, not used for OMAP4+
+ * @st_shift: status bit offset corresponding to the reset line
* @part: PRM partition
* @inst: PRM instance offset
* @rstctrl_offs: reset register offset
- * @st_offs: reset status register offset, not used for OMAP4+
+ * @rstst_offs: reset status register offset
*
* Some IPs like dsp, ipu or iva contain processors that require an HW
* reset line to be asserted / deasserted in order to fully enable the
* of reset, or -EBUSY if the submodule did not exit reset promptly.
*/
int omap4_prminst_deassert_hardreset(u8 shift, u8 st_shift, u8 part, s16 inst,
- u16 rstctrl_offs, u16 st_offs)
+ u16 rstctrl_offs, u16 rstst_offs)
{
int c;
u32 mask = 1 << shift;
- u16 rstst_offs = rstctrl_offs + OMAP4_RST_CTRL_ST_OFFSET;
+ u32 st_mask = 1 << st_shift;
/* Check the current status to avoid de-asserting the line twice */
if (omap4_prminst_is_hardreset_asserted(shift, part, inst,
return -EEXIST;
/* Clear the reset status by writing 1 to the status bit */
- omap4_prminst_rmw_inst_reg_bits(0xffffffff, mask, part, inst,
+ omap4_prminst_rmw_inst_reg_bits(0xffffffff, st_mask, part, inst,
rstst_offs);
/* de-assert the reset control line */
omap4_prminst_rmw_inst_reg_bits(mask, 0, part, inst, rstctrl_offs);
/* wait the status to be set */
- omap_test_timeout(omap4_prminst_is_hardreset_asserted(shift, part, inst,
- rstst_offs),
+ omap_test_timeout(omap4_prminst_is_hardreset_asserted(st_shift, part,
+ inst, rstst_offs),
MAX_MODULE_HARDRESET_WAIT, c);
return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
if (IS_ERR(src))
return PTR_ERR(src);
- if (clk_get_parent(timer->fclk) != src) {
- r = clk_set_parent(timer->fclk, src);
- if (r < 0) {
- pr_warn("%s: %s cannot set source\n", __func__,
- oh->name);
- clk_put(src);
- return r;
- }
+ r = clk_set_parent(timer->fclk, src);
+ if (r < 0) {
+ pr_warn("%s: %s cannot set source\n", __func__, oh->name);
+ clk_put(src);
+ return r;
}
clk_put(src);
static phys_addr_t rk3288_bootram_phy;
static struct regmap *pmu_regmap;
-static struct regmap *grf_regmap;
static struct regmap *sgrf_regmap;
static u32 rk3288_pmu_pwr_mode_con;
-static u32 rk3288_grf_soc_con0;
static u32 rk3288_sgrf_soc_con0;
static inline u32 rk3288_l2_config(void)
{
u32 mode_set, mode_set1;
- regmap_read(grf_regmap, RK3288_GRF_SOC_CON0, &rk3288_grf_soc_con0);
-
regmap_read(sgrf_regmap, RK3288_SGRF_SOC_CON0, &rk3288_sgrf_soc_con0);
regmap_read(pmu_regmap, RK3288_PMU_PWRMODE_CON,
&rk3288_pmu_pwr_mode_con);
- /*
- * We need set this bit GRF_FORCE_JTAG here, for the debug module,
- * otherwise, it may become inaccessible after resume.
- * This creates a potential security issue, as the sdmmc pins may
- * accept jtag data for a short time during resume if no card is
- * inserted.
- * But this is of course also true for the regular boot, before we
- * turn of the jtag/sdmmc autodetect.
- */
- regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, GRF_FORCE_JTAG |
- GRF_FORCE_JTAG_WRITE);
-
/*
* SGRF_FAST_BOOT_EN - system to boot from FAST_BOOT_ADDR
* PCLK_WDT_GATE - disable WDT during suspend.
regmap_write(sgrf_regmap, RK3288_SGRF_SOC_CON0,
rk3288_sgrf_soc_con0 | SGRF_PCLK_WDT_GATE_WRITE
| SGRF_FAST_BOOT_EN_WRITE);
-
- regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, rk3288_grf_soc_con0 |
- GRF_FORCE_JTAG_WRITE);
}
static int rockchip_lpmode_enter(unsigned long arg)
return PTR_ERR(pmu_regmap);
}
- grf_regmap = syscon_regmap_lookup_by_compatible(
- "rockchip,rk3288-grf");
- if (IS_ERR(grf_regmap)) {
- pr_err("%s: could not find grf regmap\n", __func__);
- return PTR_ERR(pmu_regmap);
- }
-
sram_np = of_find_compatible_node(NULL, NULL,
"rockchip,rk3288-pmu-sram");
if (!sram_np) {
#define RK3288_PMU_WAKEUP_RST_CLR_CNT 0x44
#define RK3288_PMU_PWRMODE_CON1 0x90
-#define RK3288_GRF_SOC_CON0 0x244
-#define GRF_FORCE_JTAG BIT(12)
-#define GRF_FORCE_JTAG_WRITE BIT(28)
-
#define RK3288_SGRF_SOC_CON0 (0x0000)
#define RK3288_SGRF_FAST_BOOT_ADDR (0x0120)
#define SGRF_PCLK_WDT_GATE BIT(6)
#define SEEN_DATA (1 << (BPF_MEMWORDS + 3))
#define FLAG_NEED_X_RESET (1 << 0)
+#define FLAG_IMM_OVERFLOW (1 << 1)
struct jit_ctx {
const struct bpf_prog *skf;
/* PC in ARM mode == address of the instruction + 8 */
imm = offset - (8 + ctx->idx * 4);
+ if (imm & ~0xfff) {
+ /*
+ * literal pool is too far, signal it into flags. we
+ * can only detect it on the second pass unfortunately.
+ */
+ ctx->flags |= FLAG_IMM_OVERFLOW;
+ return 0;
+ }
+
return imm;
}
return;
}
#endif
- if (rm != ARM_R0)
- emit(ARM_MOV_R(ARM_R0, rm), ctx);
+
+ /*
+ * For BPF_ALU | BPF_DIV | BPF_K instructions, rm is ARM_R4
+ * (r_A) and rn is ARM_R0 (r_scratch) so load rn first into
+ * ARM_R1 to avoid accidentally overwriting ARM_R0 with rm
+ * before using it as a source for ARM_R1.
+ *
+ * For BPF_ALU | BPF_DIV | BPF_X rm is ARM_R4 (r_A) and rn is
+ * ARM_R5 (r_X) so there is no particular register overlap
+ * issues.
+ */
if (rn != ARM_R1)
emit(ARM_MOV_R(ARM_R1, rn), ctx);
+ if (rm != ARM_R0)
+ emit(ARM_MOV_R(ARM_R0, rm), ctx);
ctx->seen |= SEEN_CALL;
emit_mov_i(ARM_R3, (u32)jit_udiv, ctx);
default:
return -1;
}
+
+ if (ctx->flags & FLAG_IMM_OVERFLOW)
+ /*
+ * this instruction generated an overflow when
+ * trying to access the literal pool, so
+ * delegate this filter to the kernel interpreter.
+ */
+ return -1;
}
/* compute offsets only during the first pass */
ctx.idx = 0;
build_prologue(&ctx);
- build_body(&ctx);
+ if (build_body(&ctx) < 0) {
+#if __LINUX_ARM_ARCH__ < 7
+ if (ctx.imm_count)
+ kfree(ctx.imms);
+#endif
+ bpf_jit_binary_free(header);
+ goto out;
+ }
build_epilogue(&ctx);
flush_icache_range((u32)ctx.target, (u32)(ctx.target + ctx.idx));
void xen_arch_post_suspend(int suspend_cancelled) { }
void xen_timer_resume(void) { }
void xen_arch_resume(void) { }
+void xen_arch_suspend(void) { }
/* In the hypervisor.S file. */
clock-output-names = "juno_mb:clk25mhz";
};
+ v2m_refclk1mhz: refclk1mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000>;
+ clock-output-names = "juno_mb:refclk1mhz";
+ };
+
+ v2m_refclk32khz: refclk32khz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "juno_mb:refclk32khz";
+ };
+
motherboard {
compatible = "arm,vexpress,v2p-p1", "simple-bus";
#address-cells = <2>; /* SMB chipselect number and offset */
#size-cells = <1>;
ranges = <0 3 0 0x200000>;
+ v2m_sysctl: sysctl@020000 {
+ compatible = "arm,sp810", "arm,primecell";
+ reg = <0x020000 0x1000>;
+ clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&mb_clk24mhz>;
+ clock-names = "refclk", "timclk", "apb_pclk";
+ #clock-cells = <1>;
+ clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3";
+ };
+
mmci@050000 {
compatible = "arm,pl180", "arm,primecell";
reg = <0x050000 0x1000>;
compatible = "arm,sp804", "arm,primecell";
reg = <0x110000 0x10000>;
interrupts = <9>;
- clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
- clock-names = "timclken1", "apb_pclk";
+ clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&mb_clk24mhz>;
+ clock-names = "timclken1", "timclken2", "apb_pclk";
};
v2m_timer23: timer@120000 {
compatible = "arm,sp804", "arm,primecell";
reg = <0x120000 0x10000>;
interrupts = <9>;
- clocks = <&mb_clk24mhz>, <&soc_smc50mhz>;
- clock-names = "timclken1", "apb_pclk";
+ clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&mb_clk24mhz>;
+ clock-names = "timclken1", "timclken2", "apb_pclk";
};
rtc@170000 {
{
struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+ put_unaligned_le32(ctx->crc, out);
+ return 0;
+}
+
+static int chksumc_final(struct shash_desc *desc, u8 *out)
+{
+ struct chksum_desc_ctx *ctx = shash_desc_ctx(desc);
+
put_unaligned_le32(~ctx->crc, out);
return 0;
}
static int __chksum_finup(u32 crc, const u8 *data, unsigned int len, u8 *out)
{
- put_unaligned_le32(~crc32_arm64_le_hw(crc, data, len), out);
+ put_unaligned_le32(crc32_arm64_le_hw(crc, data, len), out);
return 0;
}
{
struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
+ mctx->key = 0;
+ return 0;
+}
+
+static int crc32c_cra_init(struct crypto_tfm *tfm)
+{
+ struct chksum_ctx *mctx = crypto_tfm_ctx(tfm);
+
mctx->key = ~0;
return 0;
}
.setkey = chksum_setkey,
.init = chksum_init,
.update = chksumc_update,
- .final = chksum_final,
+ .final = chksumc_final,
.finup = chksumc_finup,
.digest = chksumc_digest,
.descsize = sizeof(struct chksum_desc_ctx),
.cra_alignmask = 0,
.cra_ctxsize = sizeof(struct chksum_ctx),
.cra_module = THIS_MODULE,
- .cra_init = crc32_cra_init,
+ .cra_init = crc32c_cra_init,
}
};
static int sha1_ce_final(struct shash_desc *desc, u8 *out)
{
+ struct sha1_ce_state *sctx = shash_desc_ctx(desc);
+
+ sctx->finalize = 0;
kernel_neon_begin_partial(16);
sha1_base_do_finalize(desc, (sha1_block_fn *)sha1_ce_transform);
kernel_neon_end();
static int sha256_ce_final(struct shash_desc *desc, u8 *out)
{
+ struct sha256_ce_state *sctx = shash_desc_ctx(desc);
+
+ sctx->finalize = 0;
kernel_neon_begin_partial(28);
sha256_base_do_finalize(desc, (sha256_block_fn *)sha2_ce_transform);
kernel_neon_end();
#include <asm/cacheflush.h>
#include <asm/alternative.h>
#include <asm/cpufeature.h>
-#include <asm/insn.h>
#include <linux/stop_machine.h>
extern struct alt_instr __alt_instructions[], __alt_instructions_end[];
struct alt_instr *end;
};
-/*
- * Decode the imm field of a b/bl instruction, and return the byte
- * offset as a signed value (so it can be used when computing a new
- * branch target).
- */
-static s32 get_branch_offset(u32 insn)
-{
- s32 imm = aarch64_insn_decode_immediate(AARCH64_INSN_IMM_26, insn);
-
- /* sign-extend the immediate before turning it into a byte offset */
- return (imm << 6) >> 4;
-}
-
-static u32 get_alt_insn(u8 *insnptr, u8 *altinsnptr)
-{
- u32 insn;
-
- aarch64_insn_read(altinsnptr, &insn);
-
- /* Stop the world on instructions we don't support... */
- BUG_ON(aarch64_insn_is_cbz(insn));
- BUG_ON(aarch64_insn_is_cbnz(insn));
- BUG_ON(aarch64_insn_is_bcond(insn));
- /* ... and there is probably more. */
-
- if (aarch64_insn_is_b(insn) || aarch64_insn_is_bl(insn)) {
- enum aarch64_insn_branch_type type;
- unsigned long target;
-
- if (aarch64_insn_is_b(insn))
- type = AARCH64_INSN_BRANCH_NOLINK;
- else
- type = AARCH64_INSN_BRANCH_LINK;
-
- target = (unsigned long)altinsnptr + get_branch_offset(insn);
- insn = aarch64_insn_gen_branch_imm((unsigned long)insnptr,
- target, type);
- }
-
- return insn;
-}
-
static int __apply_alternatives(void *alt_region)
{
struct alt_instr *alt;
u8 *origptr, *replptr;
for (alt = region->begin; alt < region->end; alt++) {
- u32 insn;
- int i;
-
if (!cpus_have_cap(alt->cpufeature))
continue;
origptr = (u8 *)&alt->orig_offset + alt->orig_offset;
replptr = (u8 *)&alt->alt_offset + alt->alt_offset;
-
- for (i = 0; i < alt->alt_len; i += sizeof(insn)) {
- insn = get_alt_insn(origptr + i, replptr + i);
- aarch64_insn_write(origptr + i, insn);
- }
-
+ memcpy(origptr, replptr, alt->alt_len);
flush_icache_range((uintptr_t)origptr,
(uintptr_t)(origptr + alt->alt_len));
}
if (!cpu_pmu)
return -ENODEV;
- irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
- if (!irqs)
- return -ENOMEM;
-
/* Don't bother with PPIs; they're already affine */
irq = platform_get_irq(pdev, 0);
if (irq >= 0 && irq_is_percpu(irq))
return 0;
+ irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
+ if (!irqs)
+ return -ENOMEM;
+
for (i = 0; i < pdev->num_resources; ++i) {
struct device_node *dn;
int cpu;
for (j = 0; j < pg_level[i].num; j++)
pg_level[i].mask |= pg_level[i].bits[j].mask;
+#ifdef CONFIG_SPARSEMEM_VMEMMAP
address_markers[VMEMMAP_START_NR].start_address =
(unsigned long)virt_to_page(PAGE_OFFSET);
address_markers[VMEMMAP_END_NR].start_address =
(unsigned long)virt_to_page(high_memory);
+#endif
pe = debugfs_create_file("kernel_page_tables", 0400, NULL, NULL,
&ptdump_fops);
return -EINVAL;
}
- imm64 = (u64)insn1.imm << 32 | imm;
+ imm64 = (u64)insn1.imm << 32 | (u32)imm;
emit_a64_mov_i64(dst, imm64, ctx);
return 1;
ifdef CONFIG_MIPS
CHECKFLAGS += $(shell $(CC) $(KBUILD_CFLAGS) -dM -E -x c /dev/null | \
egrep -vw '__GNUC_(|MINOR_|PATCHLEVEL_)_' | \
- sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/")
+ sed -e "s/^\#define /-D'/" -e "s/ /'='/" -e "s/$$/'/" -e 's/\$$/&&/g')
ifdef CONFIG_64BIT
CHECKFLAGS += -m64
endif
\
current->thread.abi = &mips_abi; \
\
- current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31; \
+ current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31; \
} while (0)
#endif /* CONFIG_32BIT */
else \
current->thread.abi = &mips_abi; \
\
- current->thread.fpu.fcr31 = current_cpu_data.fpu_csr31; \
+ current->thread.fpu.fcr31 = boot_cpu_data.fpu_csr31; \
\
p = personality(current->personality); \
if (p != PER_LINUX32 && p != PER_LINUX) \
#define SMP_DUMP 0x8
#define SMP_ASK_C0COUNT 0x10
-extern volatile cpumask_t cpu_callin_map;
+extern cpumask_t cpu_callin_map;
/* Mask of CPUs which are currently definitely operating coherently */
extern cpumask_t cpu_coherent_mask;
/* Lets see if this is an O32 ELF */
if (ehdr32->e_ident[EI_CLASS] == ELFCLASS32) {
- /* FR = 1 for N32 */
- if (ehdr32->e_flags & EF_MIPS_ABI2)
- state->overall_fp_mode = FP_FR1;
- else
- /* Set a good default FPU mode for O32 */
- state->overall_fp_mode = cpu_has_mips_r6 ?
- FP_FRE : FP_FR0;
-
if (ehdr32->e_flags & EF_MIPS_FP64) {
/*
* Set MIPS_ABI_FP_OLD_64 for EF_MIPS_FP64. We will override it
(char *)&abiflags,
sizeof(abiflags));
} else {
- /* FR=1 is really the only option for 64-bit */
- state->overall_fp_mode = FP_FR1;
-
if (phdr64->p_type != PT_MIPS_ABIFLAGS)
return 0;
if (phdr64->p_filesz < sizeof(abiflags))
struct elf32_hdr *ehdr = _ehdr;
struct mode_req prog_req, interp_req;
int fp_abi, interp_fp_abi, abi0, abi1, max_abi;
+ bool is_mips64;
if (!config_enabled(CONFIG_MIPS_O32_FP64_SUPPORT))
return 0;
abi0 = abi1 = fp_abi;
}
- /* ABI limits. O32 = FP_64A, N32/N64 = FP_SOFT */
- max_abi = ((ehdr->e_ident[EI_CLASS] == ELFCLASS32) &&
- (!(ehdr->e_flags & EF_MIPS_ABI2))) ?
- MIPS_ABI_FP_64A : MIPS_ABI_FP_SOFT;
+ is_mips64 = (ehdr->e_ident[EI_CLASS] == ELFCLASS64) ||
+ (ehdr->e_flags & EF_MIPS_ABI2);
+
+ if (is_mips64) {
+ /* MIPS64 code always uses FR=1, thus the default is easy */
+ state->overall_fp_mode = FP_FR1;
+
+ /* Disallow access to the various FPXX & FP64 ABIs */
+ max_abi = MIPS_ABI_FP_SOFT;
+ } else {
+ /* Default to a mode capable of running code expecting FR=0 */
+ state->overall_fp_mode = cpu_has_mips_r6 ? FP_FRE : FP_FR0;
+
+ /* Allow all ABIs we know about */
+ max_abi = MIPS_ABI_FP_64A;
+ }
if ((abi0 > max_abi && abi0 != MIPS_ABI_FP_UNKNOWN) ||
(abi1 > max_abi && abi1 != MIPS_ABI_FP_UNKNOWN))
__get_user(value, data + 64);
fcr31 = child->thread.fpu.fcr31;
- mask = current_cpu_data.fpu_msk31;
+ mask = boot_cpu_data.fpu_msk31;
child->thread.fpu.fcr31 = (value & ~mask) | (fcr31 & mask);
/* FIR may not be written. */
#ifdef CONFIG_MIPS_MT_FPAFF
/* If we have an FPU, enroll ourselves in the FPU-full mask */
if (cpu_has_fpu)
- cpu_set(0, mt_fpu_cpumask);
+ cpumask_set_cpu(0, &mt_fpu_cpumask);
#endif /* CONFIG_MIPS_MT_FPAFF */
}
#include <asm/time.h>
#include <asm/setup.h>
-volatile cpumask_t cpu_callin_map; /* Bitmask of started secondaries */
+cpumask_t cpu_callin_map; /* Bitmask of started secondaries */
int __cpu_number_map[NR_CPUS]; /* Map physical to logical */
EXPORT_SYMBOL(__cpu_number_map);
/*
* Trust is futile. We should really have timeouts ...
*/
- while (!cpumask_test_cpu(cpu, &cpu_callin_map))
+ while (!cpumask_test_cpu(cpu, &cpu_callin_map)) {
udelay(100);
+ schedule();
+ }
synchronise_count_master(cpu);
return 0;
*/
printk("epc : %0*lx %pS\n", field, regs->cp0_epc,
(void *) regs->cp0_epc);
- printk(" %s\n", print_tainted());
printk("ra : %0*lx %pS\n", field, regs->regs[31],
(void *) regs->regs[31]);
{
unsigned long *gpr = &vcpu->arch.gprs[vcpu->arch.io_gpr];
enum emulation_result er = EMULATE_DONE;
- unsigned long curr_pc;
if (run->mmio.len > sizeof(*gpr)) {
kvm_err("Bad MMIO length: %d", run->mmio.len);
goto done;
}
- /*
- * Update PC and hold onto current PC in case there is
- * an error and we want to rollback the PC
- */
- curr_pc = vcpu->arch.pc;
er = update_pc(vcpu, vcpu->arch.pending_load_cause);
if (er == EMULATE_FAIL)
return er;
break;
case FPCREG_RID:
- value = current_cpu_data.fpu_id;
+ value = boot_cpu_data.fpu_id;
break;
default:
(void *)xcp->cp0_epc, MIPSInst_RT(ir), value);
/* Preserve read-only bits. */
- mask = current_cpu_data.fpu_msk31;
+ mask = boot_cpu_data.fpu_msk31;
fcr31 = (value & ~mask) | (fcr31 & mask);
break;
if (cpu_has_rixi) {
/*
- * Enable the no read, no exec bits, and enable large virtual
+ * Enable the no read, no exec bits, and enable large physical
* address.
*/
#ifdef CONFIG_64BIT
.resource = ip32_rtc_resources,
};
-+static int __init sgio2_rtc_devinit(void)
+static __init int sgio2_rtc_devinit(void)
{
return platform_device_register(&ip32_rtc_device);
}
-device_initcall(sgio2_cmos_devinit);
+device_initcall(sgio2_rtc_devinit);
#define ELF_HWCAP 0
+#define STACK_RND_MASK (is_32bit_task() ? \
+ 0x7ff >> (PAGE_SHIFT - 12) : \
+ 0x3ffff >> (PAGE_SHIFT - 12))
+
struct mm_struct;
extern unsigned long arch_randomize_brk(struct mm_struct *);
#define arch_randomize_brk arch_randomize_brk
return 1;
}
+/*
+ * Copy architecture-specific thread state
+ */
int
copy_thread(unsigned long clone_flags, unsigned long usp,
- unsigned long arg, struct task_struct *p)
+ unsigned long kthread_arg, struct task_struct *p)
{
struct pt_regs *cregs = &(p->thread.regs);
void *stack = task_stack_page(p);
extern void * const child_return;
if (unlikely(p->flags & PF_KTHREAD)) {
+ /* kernel thread */
memset(cregs, 0, sizeof(struct pt_regs));
if (!usp) /* idle thread */
return 0;
-
- /* kernel thread */
/* Must exit via ret_from_kernel_thread in order
* to call schedule_tail()
*/
#else
cregs->gr[26] = usp;
#endif
- cregs->gr[25] = arg;
+ cregs->gr[25] = kthread_arg;
} else {
/* user thread */
/* usp must be word aligned. This also prevents users from
if (stack_base > STACK_SIZE_MAX)
stack_base = STACK_SIZE_MAX;
+ /* Add space for stack randomization. */
+ stack_base += (STACK_RND_MASK << PAGE_SHIFT);
+
return PAGE_ALIGN(STACK_TOP - stack_base);
}
uint64_t nip, uint64_t addr)
{
uint64_t srr1;
- int index = __this_cpu_inc_return(mce_nest_count);
+ int index = __this_cpu_inc_return(mce_nest_count) - 1;
struct machine_check_event *mce = this_cpu_ptr(&mce_event[index]);
/*
if (!get_mce_event(&evt, MCE_EVENT_RELEASE))
return;
- index = __this_cpu_inc_return(mce_queue_count);
+ index = __this_cpu_inc_return(mce_queue_count) - 1;
/* If queue is full, just return for now. */
if (index >= MAX_MC_EVT) {
__this_cpu_dec(mce_queue_count);
*(.opd)
}
+ . = ALIGN(256);
.got : AT(ADDR(.got) - LOAD_OFFSET) {
__toc_start = .;
#ifndef CONFIG_RELOCATABLE
*/
static noinline void kvmppc_run_core(struct kvmppc_vcore *vc)
{
- struct kvm_vcpu *vcpu;
+ struct kvm_vcpu *vcpu, *vnext;
int i;
int srcu_idx;
*/
if ((threads_per_core > 1) &&
((vc->num_threads > threads_per_subcore) || !on_primary_thread())) {
- list_for_each_entry(vcpu, &vc->runnable_threads, arch.run_list) {
+ list_for_each_entry_safe(vcpu, vnext, &vc->runnable_threads,
+ arch.run_list) {
vcpu->arch.ret = -EBUSY;
kvmppc_remove_runnable(vc, vcpu);
wake_up(&vcpu->arch.cpu_run);
struct page *
follow_huge_addr(struct mm_struct *mm, unsigned long address, int write)
{
- pte_t *ptep;
- struct page *page;
+ pte_t *ptep, pte;
unsigned shift;
unsigned long mask, flags;
+ struct page *page = ERR_PTR(-EINVAL);
+
+ local_irq_save(flags);
+ ptep = find_linux_pte_or_hugepte(mm->pgd, address, &shift);
+ if (!ptep)
+ goto no_page;
+ pte = READ_ONCE(*ptep);
/*
+ * Verify it is a huge page else bail.
* Transparent hugepages are handled by generic code. We can skip them
* here.
*/
- local_irq_save(flags);
- ptep = find_linux_pte_or_hugepte(mm->pgd, address, &shift);
+ if (!shift || pmd_trans_huge(__pmd(pte_val(pte))))
+ goto no_page;
- /* Verify it is a huge page else bail. */
- if (!ptep || !shift || pmd_trans_huge(*(pmd_t *)ptep)) {
- local_irq_restore(flags);
- return ERR_PTR(-EINVAL);
+ if (!pte_present(pte)) {
+ page = NULL;
+ goto no_page;
}
mask = (1UL << shift) - 1;
- page = pte_page(*ptep);
+ page = pte_page(pte);
if (page)
page += (address & mask) / PAGE_SIZE;
+no_page:
local_irq_restore(flags);
return page;
}
* hash fault look at them.
*/
memset(pgtable, 0, PTE_FRAG_SIZE);
+ /*
+ * Serialize against find_linux_pte_or_hugepte which does lock-less
+ * lookup in page tables with local interrupts disabled. For huge pages
+ * it casts pmd_t to pte_t. Since format of pte_t is different from
+ * pmd_t we want to prevent transit from pmd pointing to page table
+ * to pmd pointing to huge page (and back) while interrupts are disabled.
+ * We clear pmd to possibly replace it with page table pointer in
+ * different code paths. So make sure we wait for the parallel
+ * find_linux_pte_or_hugepage to finish.
+ */
+ kick_all_cpus_sync();
return old_pmd;
}
#define GHASH_DIGEST_SIZE 16
struct ghash_ctx {
- u8 icv[16];
- u8 key[16];
+ u8 key[GHASH_BLOCK_SIZE];
};
struct ghash_desc_ctx {
+ u8 icv[GHASH_BLOCK_SIZE];
+ u8 key[GHASH_BLOCK_SIZE];
u8 buffer[GHASH_BLOCK_SIZE];
u32 bytes;
};
static int ghash_init(struct shash_desc *desc)
{
struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
+ struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
memset(dctx, 0, sizeof(*dctx));
+ memcpy(dctx->key, ctx->key, GHASH_BLOCK_SIZE);
return 0;
}
}
memcpy(ctx->key, key, GHASH_BLOCK_SIZE);
- memset(ctx->icv, 0, GHASH_BLOCK_SIZE);
return 0;
}
const u8 *src, unsigned int srclen)
{
struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
- struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
unsigned int n;
u8 *buf = dctx->buffer;
int ret;
src += n;
if (!dctx->bytes) {
- ret = crypt_s390_kimd(KIMD_GHASH, ctx, buf,
+ ret = crypt_s390_kimd(KIMD_GHASH, dctx, buf,
GHASH_BLOCK_SIZE);
if (ret != GHASH_BLOCK_SIZE)
return -EIO;
n = srclen & ~(GHASH_BLOCK_SIZE - 1);
if (n) {
- ret = crypt_s390_kimd(KIMD_GHASH, ctx, src, n);
+ ret = crypt_s390_kimd(KIMD_GHASH, dctx, src, n);
if (ret != n)
return -EIO;
src += n;
return 0;
}
-static int ghash_flush(struct ghash_ctx *ctx, struct ghash_desc_ctx *dctx)
+static int ghash_flush(struct ghash_desc_ctx *dctx)
{
u8 *buf = dctx->buffer;
int ret;
memset(pos, 0, dctx->bytes);
- ret = crypt_s390_kimd(KIMD_GHASH, ctx, buf, GHASH_BLOCK_SIZE);
+ ret = crypt_s390_kimd(KIMD_GHASH, dctx, buf, GHASH_BLOCK_SIZE);
if (ret != GHASH_BLOCK_SIZE)
return -EIO;
+
+ dctx->bytes = 0;
}
- dctx->bytes = 0;
return 0;
}
static int ghash_final(struct shash_desc *desc, u8 *dst)
{
struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
- struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
int ret;
- ret = ghash_flush(ctx, dctx);
+ ret = ghash_flush(dctx);
if (!ret)
- memcpy(dst, ctx->icv, GHASH_BLOCK_SIZE);
+ memcpy(dst, dctx->icv, GHASH_BLOCK_SIZE);
return ret;
}
/* fill page with urandom bytes */
get_random_bytes(pg, PAGE_SIZE);
/* exor page with stckf values */
- for (n = 0; n < sizeof(PAGE_SIZE/sizeof(u64)); n++) {
+ for (n = 0; n < PAGE_SIZE / sizeof(u64); n++) {
u64 *p = ((u64 *)pg) + n;
*p ^= get_tod_clock_fast();
}
return (pmd_val(pmd) & _SEGMENT_ENTRY_LARGE) != 0;
}
-static inline int pmd_pfn(pmd_t pmd)
+static inline unsigned long pmd_pfn(pmd_t pmd)
{
unsigned long origin_mask;
/*
* Compile one eBPF instruction into s390x code
+ *
+ * NOTE: Use noinline because for gcov (-fprofile-arcs) gcc allocates a lot of
+ * stack space for the large switch statement.
*/
-static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
+static noinline int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
{
struct bpf_insn *insn = &fp->insnsi[i];
int jmp_off, last, insn_count = 1;
EMIT4(0xb9160000, dst_reg, rc_reg);
break;
}
- case BPF_ALU64 | BPF_DIV | BPF_X: /* dst = dst / (u32) src */
- case BPF_ALU64 | BPF_MOD | BPF_X: /* dst = dst % (u32) src */
+ case BPF_ALU64 | BPF_DIV | BPF_X: /* dst = dst / src */
+ case BPF_ALU64 | BPF_MOD | BPF_X: /* dst = dst % src */
{
int rc_reg = BPF_OP(insn->code) == BPF_DIV ? REG_W1 : REG_W0;
EMIT4_IMM(0xa7090000, REG_W0, 0);
/* lgr %w1,%dst */
EMIT4(0xb9040000, REG_W1, dst_reg);
- /* llgfr %dst,%src (u32 cast) */
- EMIT4(0xb9160000, dst_reg, src_reg);
/* dlgr %w0,%dst */
- EMIT4(0xb9870000, REG_W0, dst_reg);
+ EMIT4(0xb9870000, REG_W0, src_reg);
/* lgr %dst,%rc */
EMIT4(0xb9040000, dst_reg, rc_reg);
break;
EMIT4(0xb9160000, dst_reg, rc_reg);
break;
}
- case BPF_ALU64 | BPF_DIV | BPF_K: /* dst = dst / (u32) imm */
- case BPF_ALU64 | BPF_MOD | BPF_K: /* dst = dst % (u32) imm */
+ case BPF_ALU64 | BPF_DIV | BPF_K: /* dst = dst / imm */
+ case BPF_ALU64 | BPF_MOD | BPF_K: /* dst = dst % imm */
{
int rc_reg = BPF_OP(insn->code) == BPF_DIV ? REG_W1 : REG_W0;
EMIT4(0xb9040000, REG_W1, dst_reg);
/* dlg %w0,<d(imm)>(%l) */
EMIT6_DISP_LH(0xe3000000, 0x0087, REG_W0, REG_0, REG_L,
- EMIT_CONST_U64((u32) imm));
+ EMIT_CONST_U64(imm));
/* lgr %dst,%rc */
EMIT4(0xb9040000, dst_reg, rc_reg);
break;
unsigned nxe:1;
unsigned cr0_wp:1;
unsigned smep_andnot_wp:1;
+ unsigned smap_andnot_wp:1;
};
};
struct kvm_mmu_memory_cache mmu_page_header_cache;
struct fpu guest_fpu;
+ bool eager_fpu;
u64 xcr0;
u64 guest_supported_xcr0;
u32 guest_xstate_size;
void (*cache_reg)(struct kvm_vcpu *vcpu, enum kvm_reg reg);
unsigned long (*get_rflags)(struct kvm_vcpu *vcpu);
void (*set_rflags)(struct kvm_vcpu *vcpu, unsigned long rflags);
+ void (*fpu_activate)(struct kvm_vcpu *vcpu);
void (*fpu_deactivate)(struct kvm_vcpu *vcpu);
void (*tlb_flush)(struct kvm_vcpu *vcpu);
struct pt_regs *regs)
{
int i, ret = 0;
+ char *tmp;
for (i = 0; i < mca_cfg.banks; i++) {
m->status = mce_rdmsrl(MSR_IA32_MCx_STATUS(i));
if (quirk_no_way_out)
quirk_no_way_out(i, m, regs);
}
- if (mce_severity(m, mca_cfg.tolerant, msg, true) >=
- MCE_PANIC_SEVERITY)
+
+ if (mce_severity(m, mca_cfg.tolerant, &tmp, true) >= MCE_PANIC_SEVERITY) {
+ *msg = tmp;
ret = 1;
+ }
}
return ret;
}
[ C(LL ) ] = {
[ C(OP_READ) ] = {
[ C(RESULT_ACCESS) ] = SLM_DMND_READ|SLM_LLC_ACCESS,
- [ C(RESULT_MISS) ] = SLM_DMND_READ|SLM_LLC_MISS,
+ [ C(RESULT_MISS) ] = 0,
},
[ C(OP_WRITE) ] = {
[ C(RESULT_ACCESS) ] = SLM_DMND_WRITE|SLM_LLC_ACCESS,
[ C(OP_READ) ] = {
/* OFFCORE_RESPONSE.ANY_DATA.LOCAL_CACHE */
[ C(RESULT_ACCESS) ] = 0x01b7,
- /* OFFCORE_RESPONSE.ANY_DATA.ANY_LLC_MISS */
- [ C(RESULT_MISS) ] = 0x01b7,
+ [ C(RESULT_MISS) ] = 0,
},
[ C(OP_WRITE) ] = {
/* OFFCORE_RESPONSE.ANY_RFO.LOCAL_CACHE */
[ C(ITLB) ] = {
[ C(OP_READ) ] = {
[ C(RESULT_ACCESS) ] = 0x00c0, /* INST_RETIRED.ANY_P */
- [ C(RESULT_MISS) ] = 0x0282, /* ITLB.MISSES */
+ [ C(RESULT_MISS) ] = 0x40205, /* PAGE_WALKS.I_SIDE_WALKS */
},
[ C(OP_WRITE) ] = {
[ C(RESULT_ACCESS) ] = -1,
break;
case 60: /* Haswell */
case 69: /* Haswell-Celeron */
+ case 61: /* Broadwell */
rapl_cntr_mask = RAPL_IDX_HSW;
rapl_pmu_events_group.attrs = rapl_events_hsw_attr;
break;
xstate_size = sizeof(struct i387_fxsave_struct);
else
xstate_size = sizeof(struct i387_fsave_struct);
+
+ /*
+ * Quirk: we don't yet handle the XSAVES* instructions
+ * correctly, as we don't correctly convert between
+ * standard and compacted format when interfacing
+ * with user-space - so disable it for now.
+ *
+ * The difference is small: with recent CPUs the
+ * compacted format is only marginally smaller than
+ * the standard FPU state format.
+ *
+ * ( This is easy to backport while we are fixing
+ * XSAVES* support. )
+ */
+ setup_clear_cpu_cap(X86_FEATURE_XSAVES);
}
/*
#include <linux/module.h>
#include <linux/vmalloc.h>
#include <linux/uaccess.h>
+#include <asm/i387.h> /* For use_eager_fpu. Ugh! */
+#include <asm/fpu-internal.h> /* For use_eager_fpu. Ugh! */
#include <asm/user.h>
#include <asm/xsave.h>
#include "cpuid.h"
if (best && (best->eax & (F(XSAVES) | F(XSAVEC))))
best->ebx = xstate_required_size(vcpu->arch.xcr0, true);
+ vcpu->arch.eager_fpu = guest_cpuid_has_mpx(vcpu);
+
/*
* The existing code assumes virtual address is 48-bit in the canonical
* address checks; exit if it is ever changed.
best = kvm_find_cpuid_entry(vcpu, 7, 0);
return best && (best->ebx & bit(X86_FEATURE_RTM));
}
+
+static inline bool guest_cpuid_has_mpx(struct kvm_vcpu *vcpu)
+{
+ struct kvm_cpuid_entry2 *best;
+
+ best = kvm_find_cpuid_entry(vcpu, 7, 0);
+ return best && (best->ebx & bit(X86_FEATURE_MPX));
+}
#endif
}
}
-void update_permission_bitmask(struct kvm_vcpu *vcpu,
- struct kvm_mmu *mmu, bool ept)
+static void update_permission_bitmask(struct kvm_vcpu *vcpu,
+ struct kvm_mmu *mmu, bool ept)
{
unsigned bit, byte, pfec;
u8 map;
void kvm_init_shadow_mmu(struct kvm_vcpu *vcpu)
{
bool smep = kvm_read_cr4_bits(vcpu, X86_CR4_SMEP);
+ bool smap = kvm_read_cr4_bits(vcpu, X86_CR4_SMAP);
struct kvm_mmu *context = &vcpu->arch.mmu;
MMU_WARN_ON(VALID_PAGE(context->root_hpa));
context->base_role.cr0_wp = is_write_protection(vcpu);
context->base_role.smep_andnot_wp
= smep && !is_write_protection(vcpu);
+ context->base_role.smap_andnot_wp
+ = smap && !is_write_protection(vcpu);
}
EXPORT_SYMBOL_GPL(kvm_init_shadow_mmu);
const u8 *new, int bytes)
{
gfn_t gfn = gpa >> PAGE_SHIFT;
- union kvm_mmu_page_role mask = { .word = 0 };
struct kvm_mmu_page *sp;
LIST_HEAD(invalid_list);
u64 entry, gentry, *spte;
int npte;
bool remote_flush, local_flush, zap_page;
+ union kvm_mmu_page_role mask = (union kvm_mmu_page_role) {
+ .cr0_wp = 1,
+ .cr4_pae = 1,
+ .nxe = 1,
+ .smep_andnot_wp = 1,
+ .smap_andnot_wp = 1,
+ };
/*
* If we don't have indirect shadow pages, it means no page is
++vcpu->kvm->stat.mmu_pte_write;
kvm_mmu_audit(vcpu, AUDIT_PRE_PTE_WRITE);
- mask.cr0_wp = mask.cr4_pae = mask.nxe = 1;
for_each_gfn_indirect_valid_sp(vcpu->kvm, sp, gfn) {
if (detect_write_misaligned(sp, gpa, bytes) ||
detect_write_flooding(sp)) {
int handle_mmio_page_fault_common(struct kvm_vcpu *vcpu, u64 addr, bool direct);
void kvm_init_shadow_mmu(struct kvm_vcpu *vcpu);
void kvm_init_shadow_ept_mmu(struct kvm_vcpu *vcpu, bool execonly);
-void update_permission_bitmask(struct kvm_vcpu *vcpu, struct kvm_mmu *mmu,
- bool ept);
static inline unsigned int kvm_mmu_available_pages(struct kvm *kvm)
{
int index = (pfec >> 1) +
(smap >> (X86_EFLAGS_AC_BIT - PFERR_RSVD_BIT + 1));
+ WARN_ON(pfec & PFERR_RSVD_MASK);
+
return (mmu->permissions[index] >> pte_access) & 1;
}
mmu_is_nested(vcpu));
if (likely(r != RET_MMIO_PF_INVALID))
return r;
+
+ /*
+ * page fault with PFEC.RSVD = 1 is caused by shadow
+ * page fault, should not be used to walk guest page
+ * table.
+ */
+ error_code &= ~PFERR_RSVD_MASK;
};
r = mmu_topup_memory_caches(vcpu);
.cache_reg = svm_cache_reg,
.get_rflags = svm_get_rflags,
.set_rflags = svm_set_rflags,
+ .fpu_activate = svm_fpu_activate,
.fpu_deactivate = svm_fpu_deactivate,
.tlb_flush = svm_flush_tlb,
.cache_reg = vmx_cache_reg,
.get_rflags = vmx_get_rflags,
.set_rflags = vmx_set_rflags,
+ .fpu_activate = vmx_fpu_activate,
.fpu_deactivate = vmx_fpu_deactivate,
.tlb_flush = vmx_flush_tlb,
int kvm_set_cr4(struct kvm_vcpu *vcpu, unsigned long cr4)
{
unsigned long old_cr4 = kvm_read_cr4(vcpu);
- unsigned long pdptr_bits = X86_CR4_PGE | X86_CR4_PSE |
- X86_CR4_PAE | X86_CR4_SMEP;
+ unsigned long pdptr_bits = X86_CR4_PGE | X86_CR4_PSE | X86_CR4_PAE |
+ X86_CR4_SMEP | X86_CR4_SMAP;
+
if (cr4 & CR4_RESERVED_BITS)
return 1;
(!(cr4 & X86_CR4_PCIDE) && (old_cr4 & X86_CR4_PCIDE)))
kvm_mmu_reset_context(vcpu);
- if ((cr4 ^ old_cr4) & X86_CR4_SMAP)
- update_permission_bitmask(vcpu, vcpu->arch.walk_mmu, false);
-
if ((cr4 ^ old_cr4) & X86_CR4_OSXSAVE)
kvm_update_cpuid(vcpu);
return;
page = gfn_to_page(vcpu->kvm, APIC_DEFAULT_PHYS_BASE >> PAGE_SHIFT);
+ if (is_error_page(page))
+ return;
kvm_x86_ops->set_apic_access_page_addr(vcpu, page_to_phys(page));
/*
fpu_save_init(&vcpu->arch.guest_fpu);
__kernel_fpu_end();
++vcpu->stat.fpu_reload;
- kvm_make_request(KVM_REQ_DEACTIVATE_FPU, vcpu);
+ if (!vcpu->arch.eager_fpu)
+ kvm_make_request(KVM_REQ_DEACTIVATE_FPU, vcpu);
+
trace_kvm_fpu(0);
}
struct kvm_vcpu *kvm_arch_vcpu_create(struct kvm *kvm,
unsigned int id)
{
+ struct kvm_vcpu *vcpu;
+
if (check_tsc_unstable() && atomic_read(&kvm->online_vcpus) != 0)
printk_once(KERN_WARNING
"kvm: SMP vm created on host with unstable TSC; "
"guest TSC will not be reliable\n");
- return kvm_x86_ops->vcpu_create(kvm, id);
+
+ vcpu = kvm_x86_ops->vcpu_create(kvm, id);
+
+ /*
+ * Activate fpu unconditionally in case the guest needs eager FPU. It will be
+ * deactivated soon if it doesn't.
+ */
+ kvm_x86_ops->fpu_activate(vcpu);
+ return vcpu;
}
int kvm_arch_vcpu_setup(struct kvm_vcpu *vcpu)
if (is_ereg(dst_reg))
EMIT1(0x41);
EMIT3(0xC1, add_1reg(0xC8, dst_reg), 8);
+
+ /* emit 'movzwl eax, ax' */
+ if (is_ereg(dst_reg))
+ EMIT3(0x45, 0x0F, 0xB7);
+ else
+ EMIT2(0x0F, 0xB7);
+ EMIT1(add_2reg(0xC0, dst_reg, dst_reg));
break;
case 32:
/* emit 'bswap eax' to swap lower 4 bytes */
break;
case BPF_ALU | BPF_END | BPF_FROM_LE:
+ switch (imm32) {
+ case 16:
+ /* emit 'movzwl eax, ax' to zero extend 16-bit
+ * into 64 bit
+ */
+ if (is_ereg(dst_reg))
+ EMIT3(0x45, 0x0F, 0xB7);
+ else
+ EMIT2(0x0F, 0xB7);
+ EMIT1(add_2reg(0xC0, dst_reg, dst_reg));
+ break;
+ case 32:
+ /* emit 'mov eax, eax' to clear upper 32-bits */
+ if (is_ereg(dst_reg))
+ EMIT1(0x45);
+ EMIT2(0x89, add_2reg(0xC0, dst_reg, dst_reg));
+ break;
+ case 64:
+ /* nop */
+ break;
+ }
break;
/* ST: *(u8*)(dst_reg + off) = imm */
}
ctx.cleanup_addr = proglen;
- for (pass = 0; pass < 10; pass++) {
+ /* JITed image shrinks with every pass and the loop iterates
+ * until the image stops shrinking. Very large bpf programs
+ * may converge on the last pass. In such case do one more
+ * pass to emit the final image
+ */
+ for (pass = 0; pass < 10 || image; pass++) {
proglen = do_jit(prog, addrs, image, oldproglen, &ctx);
if (proglen <= 0) {
image = NULL;
$(obj)/vdso64.so.dbg: $(src)/vdso.lds $(vobjs) FORCE
$(call if_changed,vdso)
-HOST_EXTRACFLAGS += -I$(srctree)/tools/include -I$(srctree)/include/uapi
+HOST_EXTRACFLAGS += -I$(srctree)/tools/include -I$(srctree)/include/uapi -I$(srctree)/arch/x86/include/uapi
hostprogs-y += vdso2c
quiet_cmd_vdso2c = VDSO2C $@
return -EINVAL;
}
+static inline void *dma_alloc_attrs(struct device *dev, size_t size,
+ dma_addr_t *dma_handle, gfp_t flag,
+ struct dma_attrs *attrs)
+{
+ return NULL;
+}
+
+static inline void dma_free_attrs(struct device *dev, size_t size,
+ void *vaddr, dma_addr_t dma_handle,
+ struct dma_attrs *attrs)
+{
+}
+
#endif /* _XTENSA_DMA_MAPPING_H */
}
EXPORT_SYMBOL(blk_init_queue_node);
+static void blk_queue_bio(struct request_queue *q, struct bio *bio);
+
struct request_queue *
blk_init_allocated_queue(struct request_queue *q, request_fn_proc *rfn,
spinlock_t *lock)
blk_rq_bio_prep(req->q, req, bio);
}
-void blk_queue_bio(struct request_queue *q, struct bio *bio)
+static void blk_queue_bio(struct request_queue *q, struct bio *bio)
{
const bool sync = !!(bio->bi_rw & REQ_SYNC);
struct blk_plug *plug;
spin_unlock_irq(q->queue_lock);
}
}
-EXPORT_SYMBOL_GPL(blk_queue_bio); /* for device mapper only */
/*
* If bio->bi_dev is a partition, remap the location
This option enables the user-spaces interface for random
number generator algorithms.
-config CRYPTO_USER_API_AEAD
- tristate "User-space interface for AEAD cipher algorithms"
- depends on NET
- select CRYPTO_AEAD
- select CRYPTO_USER_API
- help
- This option enables the user-spaces interface for AEAD
- cipher algorithms.
-
config CRYPTO_HASH_INFO
bool
/*
* RSGL_MAX_ENTRIES is an artificial limit where user space at maximum
* can cause the kernel to allocate RSGL_MAX_ENTRIES * ALG_MAX_PAGES
- * bytes
+ * pages
*/
#define RSGL_MAX_ENTRIES ALG_MAX_PAGES
struct af_alg_sgl rsgl[RSGL_MAX_ENTRIES];
if (err < 0)
goto unlock;
usedpages += err;
- /* chain the new scatterlist with initial list */
+ /* chain the new scatterlist with previous one */
if (cnt)
- scatterwalk_crypto_chain(ctx->rsgl[0].sg,
- ctx->rsgl[cnt].sg, 1,
- sg_nents(ctx->rsgl[cnt-1].sg));
+ af_alg_link_sg(&ctx->rsgl[cnt-1], &ctx->rsgl[cnt]);
+
/* we do not need more iovecs as we have sufficient memory */
if (outlen <= usedpages)
break;
{"_SB_", ACPI_TYPE_DEVICE, NULL},
{"_SI_", ACPI_TYPE_LOCAL_SCOPE, NULL},
{"_TZ_", ACPI_TYPE_DEVICE, NULL},
- /*
- * March, 2015:
- * The _REV object is in the process of being deprecated, because
- * other ACPI implementations permanently return 2. Thus, it
- * has little or no value. Return 2 for compatibility with
- * other ACPI implementations.
- */
- {"_REV", ACPI_TYPE_INTEGER, ACPI_CAST_PTR(char, 2)},
+ {"_REV", ACPI_TYPE_INTEGER, (char *)ACPI_CA_SUPPORT_LEVEL},
{"_OS_", ACPI_TYPE_STRING, ACPI_OS_NAME},
- {"_GL_", ACPI_TYPE_MUTEX, ACPI_CAST_PTR(char, 1)},
+ {"_GL_", ACPI_TYPE_MUTEX, (char *)1},
#if !defined (ACPI_NO_METHOD_EXECUTION) || defined (ACPI_CONSTANT_EVAL_ONLY)
- {"_OSI", ACPI_TYPE_METHOD, ACPI_CAST_PTR(char, 1)},
+ {"_OSI", ACPI_TYPE_METHOD, (char *)1},
#endif
/* Table terminator */
request_mem_region(addr, length, desc);
}
-static int __init acpi_reserve_resources(void)
+static void __init acpi_reserve_resources(void)
{
acpi_request_region(&acpi_gbl_FADT.xpm1a_event_block, acpi_gbl_FADT.pm1_event_length,
"ACPI PM1a_EVT_BLK");
if (!(acpi_gbl_FADT.gpe1_block_length & 0x1))
acpi_request_region(&acpi_gbl_FADT.xgpe1_block,
acpi_gbl_FADT.gpe1_block_length, "ACPI GPE1_BLK");
-
- return 0;
}
-device_initcall(acpi_reserve_resources);
void acpi_os_printf(const char *fmt, ...)
{
acpi_status __init acpi_os_initialize1(void)
{
+ acpi_reserve_resources();
kacpid_wq = alloc_workqueue("kacpid", 0, 1);
kacpi_notify_wq = alloc_workqueue("kacpi_notify", 0, 1);
kacpi_hotplug_wq = alloc_ordered_workqueue("kacpi_hotplug", 0);
config SATA_DWC
tristate "DesignWare Cores SATA support"
depends on 460EX
+ select DW_DMAC
help
This option enables support for the on-chip SATA controller of the
AppliedMicro processor 460EX.
If unsure, say N.
-config PATA_SCC
- tristate "Toshiba's Cell Reference Set IDE support"
- depends on PCI && PPC_CELLEB
- help
- This option enables support for the built-in IDE controller on
- Toshiba Cell Reference Board.
-
- If unsure, say N.
-
config PATA_SCH
tristate "Intel SCH PATA support"
depends on PCI
obj-$(CONFIG_PATA_RADISYS) += pata_radisys.o
obj-$(CONFIG_PATA_RDC) += pata_rdc.o
obj-$(CONFIG_PATA_SC1200) += pata_sc1200.o
-obj-$(CONFIG_PATA_SCC) += pata_scc.o
obj-$(CONFIG_PATA_SCH) += pata_sch.o
obj-$(CONFIG_PATA_SERVERWORKS) += pata_serverworks.o
obj-$(CONFIG_PATA_SIL680) += pata_sil680.o
board_ahci_yes_fbs,
/* board IDs for specific chipsets in alphabetical order */
+ board_ahci_avn,
board_ahci_mcp65,
board_ahci_mcp77,
board_ahci_mcp89,
static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent);
static int ahci_vt8251_hardreset(struct ata_link *link, unsigned int *class,
unsigned long deadline);
+static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline);
static void ahci_mcp89_apple_enable(struct pci_dev *pdev);
static bool is_mcp89_apple(struct pci_dev *pdev);
static int ahci_p5wdh_hardreset(struct ata_link *link, unsigned int *class,
.hardreset = ahci_p5wdh_hardreset,
};
+static struct ata_port_operations ahci_avn_ops = {
+ .inherits = &ahci_ops,
+ .hardreset = ahci_avn_hardreset,
+};
+
static const struct ata_port_info ahci_port_info[] = {
/* by features */
[board_ahci] = {
.port_ops = &ahci_ops,
},
/* by chipsets */
+ [board_ahci_avn] = {
+ .flags = AHCI_FLAG_COMMON,
+ .pio_mask = ATA_PIO4,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_avn_ops,
+ },
[board_ahci_mcp65] = {
AHCI_HFLAGS (AHCI_HFLAG_NO_FPDMA_AA | AHCI_HFLAG_NO_PMP |
AHCI_HFLAG_YES_NCQ),
{ PCI_VDEVICE(INTEL, 0x1f27), board_ahci }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f2e), board_ahci }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x1f2f), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f32), board_ahci }, /* Avoton AHCI */
- { PCI_VDEVICE(INTEL, 0x1f33), board_ahci }, /* Avoton AHCI */
- { PCI_VDEVICE(INTEL, 0x1f34), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f35), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f36), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f37), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f3e), board_ahci }, /* Avoton RAID */
- { PCI_VDEVICE(INTEL, 0x1f3f), board_ahci }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f32), board_ahci_avn }, /* Avoton AHCI */
+ { PCI_VDEVICE(INTEL, 0x1f33), board_ahci_avn }, /* Avoton AHCI */
+ { PCI_VDEVICE(INTEL, 0x1f34), board_ahci_avn }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f35), board_ahci_avn }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f36), board_ahci_avn }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f37), board_ahci_avn }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f3e), board_ahci_avn }, /* Avoton RAID */
+ { PCI_VDEVICE(INTEL, 0x1f3f), board_ahci_avn }, /* Avoton RAID */
{ PCI_VDEVICE(INTEL, 0x2823), board_ahci }, /* Wellsburg RAID */
{ PCI_VDEVICE(INTEL, 0x2827), board_ahci }, /* Wellsburg RAID */
{ PCI_VDEVICE(INTEL, 0x8d02), board_ahci }, /* Wellsburg AHCI */
return rc;
}
+/*
+ * ahci_avn_hardreset - attempt more aggressive recovery of Avoton ports.
+ *
+ * It has been observed with some SSDs that the timing of events in the
+ * link synchronization phase can leave the port in a state that can not
+ * be recovered by a SATA-hard-reset alone. The failing signature is
+ * SStatus.DET stuck at 1 ("Device presence detected but Phy
+ * communication not established"). It was found that unloading and
+ * reloading the driver when this problem occurs allows the drive
+ * connection to be recovered (DET advanced to 0x3). The critical
+ * component of reloading the driver is that the port state machines are
+ * reset by bouncing "port enable" in the AHCI PCS configuration
+ * register. So, reproduce that effect by bouncing a port whenever we
+ * see DET==1 after a reset.
+ */
+static int ahci_avn_hardreset(struct ata_link *link, unsigned int *class,
+ unsigned long deadline)
+{
+ const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context);
+ struct ata_port *ap = link->ap;
+ struct ahci_port_priv *pp = ap->private_data;
+ struct ahci_host_priv *hpriv = ap->host->private_data;
+ u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG;
+ unsigned long tmo = deadline - jiffies;
+ struct ata_taskfile tf;
+ bool online;
+ int rc, i;
+
+ DPRINTK("ENTER\n");
+
+ ahci_stop_engine(ap);
+
+ for (i = 0; i < 2; i++) {
+ u16 val;
+ u32 sstatus;
+ int port = ap->port_no;
+ struct ata_host *host = ap->host;
+ struct pci_dev *pdev = to_pci_dev(host->dev);
+
+ /* clear D2H reception area to properly wait for D2H FIS */
+ ata_tf_init(link->device, &tf);
+ tf.command = ATA_BUSY;
+ ata_tf_to_fis(&tf, 0, 0, d2h_fis);
+
+ rc = sata_link_hardreset(link, timing, deadline, &online,
+ ahci_check_ready);
+
+ if (sata_scr_read(link, SCR_STATUS, &sstatus) != 0 ||
+ (sstatus & 0xf) != 1)
+ break;
+
+ ata_link_printk(link, KERN_INFO, "avn bounce port%d\n",
+ port);
+
+ pci_read_config_word(pdev, 0x92, &val);
+ val &= ~(1 << port);
+ pci_write_config_word(pdev, 0x92, val);
+ ata_msleep(ap, 1000);
+ val |= 1 << port;
+ pci_write_config_word(pdev, 0x92, val);
+ deadline += tmo;
+ }
+
+ hpriv->start_engine(ap);
+
+ if (online)
+ *class = ahci_dev_classify(ap);
+
+ DPRINTK("EXIT, rc=%d, class=%u\n", rc, *class);
+ return rc;
+}
+
+
#ifdef CONFIG_PM
static int ahci_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
{
struct reset_control *pwr;
struct reset_control *sw_rst;
struct reset_control *pwr_rst;
- struct ahci_host_priv *hpriv;
};
static void st_ahci_configure_oob(void __iomem *mmio)
writel(new_val, mmio + ST_AHCI_OOBR);
}
-static int st_ahci_deassert_resets(struct device *dev)
+static int st_ahci_deassert_resets(struct ahci_host_priv *hpriv,
+ struct device *dev)
{
- struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
+ struct st_ahci_drv_data *drv_data = hpriv->plat_data;
int err;
if (drv_data->pwr) {
static void st_ahci_host_stop(struct ata_host *host)
{
struct ahci_host_priv *hpriv = host->private_data;
+ struct st_ahci_drv_data *drv_data = hpriv->plat_data;
struct device *dev = host->dev;
- struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
int err;
if (drv_data->pwr) {
ahci_platform_disable_resources(hpriv);
}
-static int st_ahci_probe_resets(struct platform_device *pdev)
+static int st_ahci_probe_resets(struct ahci_host_priv *hpriv,
+ struct device *dev)
{
- struct st_ahci_drv_data *drv_data = platform_get_drvdata(pdev);
+ struct st_ahci_drv_data *drv_data = hpriv->plat_data;
- drv_data->pwr = devm_reset_control_get(&pdev->dev, "pwr-dwn");
+ drv_data->pwr = devm_reset_control_get(dev, "pwr-dwn");
if (IS_ERR(drv_data->pwr)) {
- dev_info(&pdev->dev, "power reset control not defined\n");
+ dev_info(dev, "power reset control not defined\n");
drv_data->pwr = NULL;
}
- drv_data->sw_rst = devm_reset_control_get(&pdev->dev, "sw-rst");
+ drv_data->sw_rst = devm_reset_control_get(dev, "sw-rst");
if (IS_ERR(drv_data->sw_rst)) {
- dev_info(&pdev->dev, "soft reset control not defined\n");
+ dev_info(dev, "soft reset control not defined\n");
drv_data->sw_rst = NULL;
}
- drv_data->pwr_rst = devm_reset_control_get(&pdev->dev, "pwr-rst");
+ drv_data->pwr_rst = devm_reset_control_get(dev, "pwr-rst");
if (IS_ERR(drv_data->pwr_rst)) {
- dev_dbg(&pdev->dev, "power soft reset control not defined\n");
+ dev_dbg(dev, "power soft reset control not defined\n");
drv_data->pwr_rst = NULL;
}
- return st_ahci_deassert_resets(&pdev->dev);
+ return st_ahci_deassert_resets(hpriv, dev);
}
static struct ata_port_operations st_ahci_port_ops = {
if (!drv_data)
return -ENOMEM;
- platform_set_drvdata(pdev, drv_data);
-
hpriv = ahci_platform_get_resources(pdev);
if (IS_ERR(hpriv))
return PTR_ERR(hpriv);
+ hpriv->plat_data = drv_data;
- drv_data->hpriv = hpriv;
-
- err = st_ahci_probe_resets(pdev);
+ err = st_ahci_probe_resets(hpriv, &pdev->dev);
if (err)
return err;
if (err)
return err;
- st_ahci_configure_oob(drv_data->hpriv->mmio);
+ st_ahci_configure_oob(hpriv->mmio);
err = ahci_platform_init_host(pdev, hpriv, &st_ahci_port_info,
&ahci_platform_sht);
#ifdef CONFIG_PM_SLEEP
static int st_ahci_suspend(struct device *dev)
{
- struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
- struct ahci_host_priv *hpriv = drv_data->hpriv;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
+ struct st_ahci_drv_data *drv_data = hpriv->plat_data;
int err;
err = ahci_platform_suspend_host(dev);
static int st_ahci_resume(struct device *dev)
{
- struct st_ahci_drv_data *drv_data = dev_get_drvdata(dev);
- struct ahci_host_priv *hpriv = drv_data->hpriv;
+ struct ata_host *host = dev_get_drvdata(dev);
+ struct ahci_host_priv *hpriv = host->private_data;
int err;
err = ahci_platform_enable_resources(hpriv);
if (err)
return err;
- err = st_ahci_deassert_resets(dev);
+ err = st_ahci_deassert_resets(hpriv, dev);
if (err) {
ahci_platform_disable_resources(hpriv);
return err;
}
- st_ahci_configure_oob(drv_data->hpriv->mmio);
+ st_ahci_configure_oob(hpriv->mmio);
return ahci_platform_resume_host(dev);
}
if (unlikely(resetting))
status &= ~PORT_IRQ_BAD_PMP;
- /* if LPM is enabled, PHYRDY doesn't mean anything */
- if (ap->link.lpm_policy > ATA_LPM_MAX_POWER) {
+ if (sata_lpm_ignore_phy_events(&ap->link)) {
status &= ~PORT_IRQ_PHYRDY;
ahci_scr_write(&ap->link, SCR_ERROR, SERR_PHYRDY_CHG);
}
ATA_HORKAGE_ZERO_AFTER_TRIM, },
{ "Crucial_CT*MX100*", "MU01", ATA_HORKAGE_NO_NCQ_TRIM |
ATA_HORKAGE_ZERO_AFTER_TRIM, },
- { "Samsung SSD 850 PRO*", NULL, ATA_HORKAGE_NO_NCQ_TRIM |
+ { "Samsung SSD 8*", NULL, ATA_HORKAGE_NO_NCQ_TRIM |
ATA_HORKAGE_ZERO_AFTER_TRIM, },
/*
return tmp;
}
+/**
+ * sata_lpm_ignore_phy_events - test if PHY event should be ignored
+ * @link: Link receiving the event
+ *
+ * Test whether the received PHY event has to be ignored or not.
+ *
+ * LOCKING:
+ * None:
+ *
+ * RETURNS:
+ * True if the event has to be ignored.
+ */
+bool sata_lpm_ignore_phy_events(struct ata_link *link)
+{
+ unsigned long lpm_timeout = link->last_lpm_change +
+ msecs_to_jiffies(ATA_TMOUT_SPURIOUS_PHY);
+
+ /* if LPM is enabled, PHYRDY doesn't mean anything */
+ if (link->lpm_policy > ATA_LPM_MAX_POWER)
+ return true;
+
+ /* ignore the first PHY event after the LPM policy changed
+ * as it is might be spurious
+ */
+ if ((link->flags & ATA_LFLAG_CHANGED) &&
+ time_before(jiffies, lpm_timeout))
+ return true;
+
+ return false;
+}
+EXPORT_SYMBOL_GPL(sata_lpm_ignore_phy_events);
+
/*
* Dummy port_ops
*/
}
}
+ link->last_lpm_change = jiffies;
+ link->flags |= ATA_LFLAG_CHANGED;
+
return 0;
fail:
+++ /dev/null
-/*
- * Support for IDE interfaces on Celleb platform
- *
- * (C) Copyright 2006 TOSHIBA CORPORATION
- *
- * This code is based on drivers/ata/ata_piix.c:
- * Copyright 2003-2005 Red Hat Inc
- * Copyright 2003-2005 Jeff Garzik
- * Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
- * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2003 Red Hat Inc
- *
- * and drivers/ata/ahci.c:
- * Copyright 2004-2005 Red Hat, Inc.
- *
- * and drivers/ata/libata-core.c:
- * Copyright 2003-2004 Red Hat, Inc. All rights reserved.
- * Copyright 2003-2004 Jeff Garzik
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/blkdev.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <scsi/scsi_host.h>
-#include <linux/libata.h>
-
-#define DRV_NAME "pata_scc"
-#define DRV_VERSION "0.3"
-
-#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA 0x01b4
-
-/* PCI BARs */
-#define SCC_CTRL_BAR 0
-#define SCC_BMID_BAR 1
-
-/* offset of CTRL registers */
-#define SCC_CTL_PIOSHT 0x000
-#define SCC_CTL_PIOCT 0x004
-#define SCC_CTL_MDMACT 0x008
-#define SCC_CTL_MCRCST 0x00C
-#define SCC_CTL_SDMACT 0x010
-#define SCC_CTL_SCRCST 0x014
-#define SCC_CTL_UDENVT 0x018
-#define SCC_CTL_TDVHSEL 0x020
-#define SCC_CTL_MODEREG 0x024
-#define SCC_CTL_ECMODE 0xF00
-#define SCC_CTL_MAEA0 0xF50
-#define SCC_CTL_MAEC0 0xF54
-#define SCC_CTL_CCKCTRL 0xFF0
-
-/* offset of BMID registers */
-#define SCC_DMA_CMD 0x000
-#define SCC_DMA_STATUS 0x004
-#define SCC_DMA_TABLE_OFS 0x008
-#define SCC_DMA_INTMASK 0x010
-#define SCC_DMA_INTST 0x014
-#define SCC_DMA_PTERADD 0x018
-#define SCC_REG_CMD_ADDR 0x020
-#define SCC_REG_DATA 0x000
-#define SCC_REG_ERR 0x004
-#define SCC_REG_FEATURE 0x004
-#define SCC_REG_NSECT 0x008
-#define SCC_REG_LBAL 0x00C
-#define SCC_REG_LBAM 0x010
-#define SCC_REG_LBAH 0x014
-#define SCC_REG_DEVICE 0x018
-#define SCC_REG_STATUS 0x01C
-#define SCC_REG_CMD 0x01C
-#define SCC_REG_ALTSTATUS 0x020
-
-/* register value */
-#define TDVHSEL_MASTER 0x00000001
-#define TDVHSEL_SLAVE 0x00000004
-
-#define MODE_JCUSFEN 0x00000080
-
-#define ECMODE_VALUE 0x01
-
-#define CCKCTRL_ATARESET 0x00040000
-#define CCKCTRL_BUFCNT 0x00020000
-#define CCKCTRL_CRST 0x00010000
-#define CCKCTRL_OCLKEN 0x00000100
-#define CCKCTRL_ATACLKOEN 0x00000002
-#define CCKCTRL_LCLKEN 0x00000001
-
-#define QCHCD_IOS_SS 0x00000001
-
-#define QCHSD_STPDIAG 0x00020000
-
-#define INTMASK_MSK 0xD1000012
-#define INTSTS_SERROR 0x80000000
-#define INTSTS_PRERR 0x40000000
-#define INTSTS_RERR 0x10000000
-#define INTSTS_ICERR 0x01000000
-#define INTSTS_BMSINT 0x00000010
-#define INTSTS_BMHE 0x00000008
-#define INTSTS_IOIRQS 0x00000004
-#define INTSTS_INTRQ 0x00000002
-#define INTSTS_ACTEINT 0x00000001
-
-
-/* PIO transfer mode table */
-/* JCHST */
-static const unsigned long JCHSTtbl[2][7] = {
- {0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00}, /* 100MHz */
- {0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00} /* 133MHz */
-};
-
-/* JCHHT */
-static const unsigned long JCHHTtbl[2][7] = {
- {0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00}, /* 100MHz */
- {0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00} /* 133MHz */
-};
-
-/* JCHCT */
-static const unsigned long JCHCTtbl[2][7] = {
- {0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00}, /* 100MHz */
- {0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00} /* 133MHz */
-};
-
-/* DMA transfer mode table */
-/* JCHDCTM/JCHDCTS */
-static const unsigned long JCHDCTxtbl[2][7] = {
- {0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00}, /* 100MHz */
- {0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00} /* 133MHz */
-};
-
-/* JCSTWTM/JCSTWTS */
-static const unsigned long JCSTWTxtbl[2][7] = {
- {0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00}, /* 100MHz */
- {0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
-};
-
-/* JCTSS */
-static const unsigned long JCTSStbl[2][7] = {
- {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00}, /* 100MHz */
- {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05} /* 133MHz */
-};
-
-/* JCENVT */
-static const unsigned long JCENVTtbl[2][7] = {
- {0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00}, /* 100MHz */
- {0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
-};
-
-/* JCACTSELS/JCACTSELM */
-static const unsigned long JCACTSELtbl[2][7] = {
- {0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00}, /* 100MHz */
- {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01} /* 133MHz */
-};
-
-static const struct pci_device_id scc_pci_tbl[] = {
- { PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA), 0},
- { } /* terminate list */
-};
-
-/**
- * scc_set_piomode - Initialize host controller PATA PIO timings
- * @ap: Port whose timings we are configuring
- * @adev: um
- *
- * Set PIO mode for device.
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void scc_set_piomode (struct ata_port *ap, struct ata_device *adev)
-{
- unsigned int pio = adev->pio_mode - XFER_PIO_0;
- void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
- void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
- void __iomem *piosht_port = ctrl_base + SCC_CTL_PIOSHT;
- void __iomem *pioct_port = ctrl_base + SCC_CTL_PIOCT;
- unsigned long reg;
- int offset;
-
- reg = in_be32(cckctrl_port);
- if (reg & CCKCTRL_ATACLKOEN)
- offset = 1; /* 133MHz */
- else
- offset = 0; /* 100MHz */
-
- reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
- out_be32(piosht_port, reg);
- reg = JCHCTtbl[offset][pio];
- out_be32(pioct_port, reg);
-}
-
-/**
- * scc_set_dmamode - Initialize host controller PATA DMA timings
- * @ap: Port whose timings we are configuring
- * @adev: um
- *
- * Set UDMA mode for device.
- *
- * LOCKING:
- * None (inherited from caller).
- */
-
-static void scc_set_dmamode (struct ata_port *ap, struct ata_device *adev)
-{
- unsigned int udma = adev->dma_mode;
- unsigned int is_slave = (adev->devno != 0);
- u8 speed = udma;
- void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
- void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
- void __iomem *mdmact_port = ctrl_base + SCC_CTL_MDMACT;
- void __iomem *mcrcst_port = ctrl_base + SCC_CTL_MCRCST;
- void __iomem *sdmact_port = ctrl_base + SCC_CTL_SDMACT;
- void __iomem *scrcst_port = ctrl_base + SCC_CTL_SCRCST;
- void __iomem *udenvt_port = ctrl_base + SCC_CTL_UDENVT;
- void __iomem *tdvhsel_port = ctrl_base + SCC_CTL_TDVHSEL;
- int offset, idx;
-
- if (in_be32(cckctrl_port) & CCKCTRL_ATACLKOEN)
- offset = 1; /* 133MHz */
- else
- offset = 0; /* 100MHz */
-
- if (speed >= XFER_UDMA_0)
- idx = speed - XFER_UDMA_0;
- else
- return;
-
- if (is_slave) {
- out_be32(sdmact_port, JCHDCTxtbl[offset][idx]);
- out_be32(scrcst_port, JCSTWTxtbl[offset][idx]);
- out_be32(tdvhsel_port,
- (in_be32(tdvhsel_port) & ~TDVHSEL_SLAVE) | (JCACTSELtbl[offset][idx] << 2));
- } else {
- out_be32(mdmact_port, JCHDCTxtbl[offset][idx]);
- out_be32(mcrcst_port, JCSTWTxtbl[offset][idx]);
- out_be32(tdvhsel_port,
- (in_be32(tdvhsel_port) & ~TDVHSEL_MASTER) | JCACTSELtbl[offset][idx]);
- }
- out_be32(udenvt_port,
- JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx]);
-}
-
-unsigned long scc_mode_filter(struct ata_device *adev, unsigned long mask)
-{
- /* errata A308 workaround: limit ATAPI UDMA mode to UDMA4 */
- if (adev->class == ATA_DEV_ATAPI &&
- (mask & (0xE0 << ATA_SHIFT_UDMA))) {
- printk(KERN_INFO "%s: limit ATAPI UDMA to UDMA4\n", DRV_NAME);
- mask &= ~(0xE0 << ATA_SHIFT_UDMA);
- }
- return mask;
-}
-
-/**
- * scc_tf_load - send taskfile registers to host controller
- * @ap: Port to which output is sent
- * @tf: ATA taskfile register set
- *
- * Note: Original code is ata_sff_tf_load().
- */
-
-static void scc_tf_load (struct ata_port *ap, const struct ata_taskfile *tf)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
-
- if (tf->ctl != ap->last_ctl) {
- out_be32(ioaddr->ctl_addr, tf->ctl);
- ap->last_ctl = tf->ctl;
- ata_wait_idle(ap);
- }
-
- if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
- out_be32(ioaddr->feature_addr, tf->hob_feature);
- out_be32(ioaddr->nsect_addr, tf->hob_nsect);
- out_be32(ioaddr->lbal_addr, tf->hob_lbal);
- out_be32(ioaddr->lbam_addr, tf->hob_lbam);
- out_be32(ioaddr->lbah_addr, tf->hob_lbah);
- VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
- tf->hob_feature,
- tf->hob_nsect,
- tf->hob_lbal,
- tf->hob_lbam,
- tf->hob_lbah);
- }
-
- if (is_addr) {
- out_be32(ioaddr->feature_addr, tf->feature);
- out_be32(ioaddr->nsect_addr, tf->nsect);
- out_be32(ioaddr->lbal_addr, tf->lbal);
- out_be32(ioaddr->lbam_addr, tf->lbam);
- out_be32(ioaddr->lbah_addr, tf->lbah);
- VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
- tf->feature,
- tf->nsect,
- tf->lbal,
- tf->lbam,
- tf->lbah);
- }
-
- if (tf->flags & ATA_TFLAG_DEVICE) {
- out_be32(ioaddr->device_addr, tf->device);
- VPRINTK("device 0x%X\n", tf->device);
- }
-
- ata_wait_idle(ap);
-}
-
-/**
- * scc_check_status - Read device status reg & clear interrupt
- * @ap: port where the device is
- *
- * Note: Original code is ata_check_status().
- */
-
-static u8 scc_check_status (struct ata_port *ap)
-{
- return in_be32(ap->ioaddr.status_addr);
-}
-
-/**
- * scc_tf_read - input device's ATA taskfile shadow registers
- * @ap: Port from which input is read
- * @tf: ATA taskfile register set for storing input
- *
- * Note: Original code is ata_sff_tf_read().
- */
-
-static void scc_tf_read (struct ata_port *ap, struct ata_taskfile *tf)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
-
- tf->command = scc_check_status(ap);
- tf->feature = in_be32(ioaddr->error_addr);
- tf->nsect = in_be32(ioaddr->nsect_addr);
- tf->lbal = in_be32(ioaddr->lbal_addr);
- tf->lbam = in_be32(ioaddr->lbam_addr);
- tf->lbah = in_be32(ioaddr->lbah_addr);
- tf->device = in_be32(ioaddr->device_addr);
-
- if (tf->flags & ATA_TFLAG_LBA48) {
- out_be32(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
- tf->hob_feature = in_be32(ioaddr->error_addr);
- tf->hob_nsect = in_be32(ioaddr->nsect_addr);
- tf->hob_lbal = in_be32(ioaddr->lbal_addr);
- tf->hob_lbam = in_be32(ioaddr->lbam_addr);
- tf->hob_lbah = in_be32(ioaddr->lbah_addr);
- out_be32(ioaddr->ctl_addr, tf->ctl);
- ap->last_ctl = tf->ctl;
- }
-}
-
-/**
- * scc_exec_command - issue ATA command to host controller
- * @ap: port to which command is being issued
- * @tf: ATA taskfile register set
- *
- * Note: Original code is ata_sff_exec_command().
- */
-
-static void scc_exec_command (struct ata_port *ap,
- const struct ata_taskfile *tf)
-{
- DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
-
- out_be32(ap->ioaddr.command_addr, tf->command);
- ata_sff_pause(ap);
-}
-
-/**
- * scc_check_altstatus - Read device alternate status reg
- * @ap: port where the device is
- */
-
-static u8 scc_check_altstatus (struct ata_port *ap)
-{
- return in_be32(ap->ioaddr.altstatus_addr);
-}
-
-/**
- * scc_dev_select - Select device 0/1 on ATA bus
- * @ap: ATA channel to manipulate
- * @device: ATA device (numbered from zero) to select
- *
- * Note: Original code is ata_sff_dev_select().
- */
-
-static void scc_dev_select (struct ata_port *ap, unsigned int device)
-{
- u8 tmp;
-
- if (device == 0)
- tmp = ATA_DEVICE_OBS;
- else
- tmp = ATA_DEVICE_OBS | ATA_DEV1;
-
- out_be32(ap->ioaddr.device_addr, tmp);
- ata_sff_pause(ap);
-}
-
-/**
- * scc_set_devctl - Write device control reg
- * @ap: port where the device is
- * @ctl: value to write
- */
-
-static void scc_set_devctl(struct ata_port *ap, u8 ctl)
-{
- out_be32(ap->ioaddr.ctl_addr, ctl);
-}
-
-/**
- * scc_bmdma_setup - Set up PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * Note: Original code is ata_bmdma_setup().
- */
-
-static void scc_bmdma_setup (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
- u8 dmactl;
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- /* load PRD table addr */
- out_be32(mmio + SCC_DMA_TABLE_OFS, ap->bmdma_prd_dma);
-
- /* specify data direction, triple-check start bit is clear */
- dmactl = in_be32(mmio + SCC_DMA_CMD);
- dmactl &= ~(ATA_DMA_WR | ATA_DMA_START);
- if (!rw)
- dmactl |= ATA_DMA_WR;
- out_be32(mmio + SCC_DMA_CMD, dmactl);
-
- /* issue r/w command */
- ap->ops->sff_exec_command(ap, &qc->tf);
-}
-
-/**
- * scc_bmdma_start - Start a PCI IDE BMDMA transaction
- * @qc: Info associated with this ATA transaction.
- *
- * Note: Original code is ata_bmdma_start().
- */
-
-static void scc_bmdma_start (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- u8 dmactl;
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- /* start host DMA transaction */
- dmactl = in_be32(mmio + SCC_DMA_CMD);
- out_be32(mmio + SCC_DMA_CMD, dmactl | ATA_DMA_START);
-}
-
-/**
- * scc_devchk - PATA device presence detection
- * @ap: ATA channel to examine
- * @device: Device to examine (starting at zero)
- *
- * Note: Original code is ata_devchk().
- */
-
-static unsigned int scc_devchk (struct ata_port *ap,
- unsigned int device)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
- u8 nsect, lbal;
-
- ap->ops->sff_dev_select(ap, device);
-
- out_be32(ioaddr->nsect_addr, 0x55);
- out_be32(ioaddr->lbal_addr, 0xaa);
-
- out_be32(ioaddr->nsect_addr, 0xaa);
- out_be32(ioaddr->lbal_addr, 0x55);
-
- out_be32(ioaddr->nsect_addr, 0x55);
- out_be32(ioaddr->lbal_addr, 0xaa);
-
- nsect = in_be32(ioaddr->nsect_addr);
- lbal = in_be32(ioaddr->lbal_addr);
-
- if ((nsect == 0x55) && (lbal == 0xaa))
- return 1; /* we found a device */
-
- return 0; /* nothing found */
-}
-
-/**
- * scc_wait_after_reset - wait for devices to become ready after reset
- *
- * Note: Original code is ata_sff_wait_after_reset
- */
-
-static int scc_wait_after_reset(struct ata_link *link, unsigned int devmask,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- struct ata_ioports *ioaddr = &ap->ioaddr;
- unsigned int dev0 = devmask & (1 << 0);
- unsigned int dev1 = devmask & (1 << 1);
- int rc, ret = 0;
-
- /* Spec mandates ">= 2ms" before checking status. We wait
- * 150ms, because that was the magic delay used for ATAPI
- * devices in Hale Landis's ATADRVR, for the period of time
- * between when the ATA command register is written, and then
- * status is checked. Because waiting for "a while" before
- * checking status is fine, post SRST, we perform this magic
- * delay here as well.
- *
- * Old drivers/ide uses the 2mS rule and then waits for ready.
- */
- ata_msleep(ap, 150);
-
- /* always check readiness of the master device */
- rc = ata_sff_wait_ready(link, deadline);
- /* -ENODEV means the odd clown forgot the D7 pulldown resistor
- * and TF status is 0xff, bail out on it too.
- */
- if (rc)
- return rc;
-
- /* if device 1 was found in ata_devchk, wait for register
- * access briefly, then wait for BSY to clear.
- */
- if (dev1) {
- int i;
-
- ap->ops->sff_dev_select(ap, 1);
-
- /* Wait for register access. Some ATAPI devices fail
- * to set nsect/lbal after reset, so don't waste too
- * much time on it. We're gonna wait for !BSY anyway.
- */
- for (i = 0; i < 2; i++) {
- u8 nsect, lbal;
-
- nsect = in_be32(ioaddr->nsect_addr);
- lbal = in_be32(ioaddr->lbal_addr);
- if ((nsect == 1) && (lbal == 1))
- break;
- ata_msleep(ap, 50); /* give drive a breather */
- }
-
- rc = ata_sff_wait_ready(link, deadline);
- if (rc) {
- if (rc != -ENODEV)
- return rc;
- ret = rc;
- }
- }
-
- /* is all this really necessary? */
- ap->ops->sff_dev_select(ap, 0);
- if (dev1)
- ap->ops->sff_dev_select(ap, 1);
- if (dev0)
- ap->ops->sff_dev_select(ap, 0);
-
- return ret;
-}
-
-/**
- * scc_bus_softreset - PATA device software reset
- *
- * Note: Original code is ata_bus_softreset().
- */
-
-static int scc_bus_softreset(struct ata_port *ap, unsigned int devmask,
- unsigned long deadline)
-{
- struct ata_ioports *ioaddr = &ap->ioaddr;
-
- DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
-
- /* software reset. causes dev0 to be selected */
- out_be32(ioaddr->ctl_addr, ap->ctl);
- udelay(20);
- out_be32(ioaddr->ctl_addr, ap->ctl | ATA_SRST);
- udelay(20);
- out_be32(ioaddr->ctl_addr, ap->ctl);
-
- return scc_wait_after_reset(&ap->link, devmask, deadline);
-}
-
-/**
- * scc_softreset - reset host port via ATA SRST
- * @ap: port to reset
- * @classes: resulting classes of attached devices
- * @deadline: deadline jiffies for the operation
- *
- * Note: Original code is ata_sff_softreset().
- */
-
-static int scc_softreset(struct ata_link *link, unsigned int *classes,
- unsigned long deadline)
-{
- struct ata_port *ap = link->ap;
- unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
- unsigned int devmask = 0;
- int rc;
- u8 err;
-
- DPRINTK("ENTER\n");
-
- /* determine if device 0/1 are present */
- if (scc_devchk(ap, 0))
- devmask |= (1 << 0);
- if (slave_possible && scc_devchk(ap, 1))
- devmask |= (1 << 1);
-
- /* select device 0 again */
- ap->ops->sff_dev_select(ap, 0);
-
- /* issue bus reset */
- DPRINTK("about to softreset, devmask=%x\n", devmask);
- rc = scc_bus_softreset(ap, devmask, deadline);
- if (rc) {
- ata_port_err(ap, "SRST failed (err_mask=0x%x)\n", rc);
- return -EIO;
- }
-
- /* determine by signature whether we have ATA or ATAPI devices */
- classes[0] = ata_sff_dev_classify(&ap->link.device[0],
- devmask & (1 << 0), &err);
- if (slave_possible && err != 0x81)
- classes[1] = ata_sff_dev_classify(&ap->link.device[1],
- devmask & (1 << 1), &err);
-
- DPRINTK("EXIT, classes[0]=%u [1]=%u\n", classes[0], classes[1]);
- return 0;
-}
-
-/**
- * scc_bmdma_stop - Stop PCI IDE BMDMA transfer
- * @qc: Command we are ending DMA for
- */
-
-static void scc_bmdma_stop (struct ata_queued_cmd *qc)
-{
- struct ata_port *ap = qc->ap;
- void __iomem *ctrl_base = ap->host->iomap[SCC_CTRL_BAR];
- void __iomem *bmid_base = ap->host->iomap[SCC_BMID_BAR];
- u32 reg;
-
- while (1) {
- reg = in_be32(bmid_base + SCC_DMA_INTST);
-
- if (reg & INTSTS_SERROR) {
- printk(KERN_WARNING "%s: SERROR\n", DRV_NAME);
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_SERROR|INTSTS_BMSINT);
- out_be32(bmid_base + SCC_DMA_CMD,
- in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
- continue;
- }
-
- if (reg & INTSTS_PRERR) {
- u32 maea0, maec0;
- maea0 = in_be32(ctrl_base + SCC_CTL_MAEA0);
- maec0 = in_be32(ctrl_base + SCC_CTL_MAEC0);
- printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", DRV_NAME, maea0, maec0);
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_PRERR|INTSTS_BMSINT);
- out_be32(bmid_base + SCC_DMA_CMD,
- in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
- continue;
- }
-
- if (reg & INTSTS_RERR) {
- printk(KERN_WARNING "%s: Response Error\n", DRV_NAME);
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_RERR|INTSTS_BMSINT);
- out_be32(bmid_base + SCC_DMA_CMD,
- in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
- continue;
- }
-
- if (reg & INTSTS_ICERR) {
- out_be32(bmid_base + SCC_DMA_CMD,
- in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
- printk(KERN_WARNING "%s: Illegal Configuration\n", DRV_NAME);
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ICERR|INTSTS_BMSINT);
- continue;
- }
-
- if (reg & INTSTS_BMSINT) {
- unsigned int classes;
- unsigned long deadline = ata_deadline(jiffies, ATA_TMOUT_BOOT);
- printk(KERN_WARNING "%s: Internal Bus Error\n", DRV_NAME);
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMSINT);
- /* TBD: SW reset */
- scc_softreset(&ap->link, &classes, deadline);
- continue;
- }
-
- if (reg & INTSTS_BMHE) {
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_BMHE);
- continue;
- }
-
- if (reg & INTSTS_ACTEINT) {
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_ACTEINT);
- continue;
- }
-
- if (reg & INTSTS_IOIRQS) {
- out_be32(bmid_base + SCC_DMA_INTST, INTSTS_IOIRQS);
- continue;
- }
- break;
- }
-
- /* clear start/stop bit */
- out_be32(bmid_base + SCC_DMA_CMD,
- in_be32(bmid_base + SCC_DMA_CMD) & ~ATA_DMA_START);
-
- /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
- ata_sff_dma_pause(ap); /* dummy read */
-}
-
-/**
- * scc_bmdma_status - Read PCI IDE BMDMA status
- * @ap: Port associated with this ATA transaction.
- */
-
-static u8 scc_bmdma_status (struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
- u8 host_stat = in_be32(mmio + SCC_DMA_STATUS);
- u32 int_status = in_be32(mmio + SCC_DMA_INTST);
- struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag);
- static int retry = 0;
-
- /* return if IOS_SS is cleared */
- if (!(in_be32(mmio + SCC_DMA_CMD) & ATA_DMA_START))
- return host_stat;
-
- /* errata A252,A308 workaround: Step4 */
- if ((scc_check_altstatus(ap) & ATA_ERR)
- && (int_status & INTSTS_INTRQ))
- return (host_stat | ATA_DMA_INTR);
-
- /* errata A308 workaround Step5 */
- if (int_status & INTSTS_IOIRQS) {
- host_stat |= ATA_DMA_INTR;
-
- /* We don't check ATAPI DMA because it is limited to UDMA4 */
- if ((qc->tf.protocol == ATA_PROT_DMA &&
- qc->dev->xfer_mode > XFER_UDMA_4)) {
- if (!(int_status & INTSTS_ACTEINT)) {
- printk(KERN_WARNING "ata%u: operation failed (transfer data loss)\n",
- ap->print_id);
- host_stat |= ATA_DMA_ERR;
- if (retry++)
- ap->udma_mask &= ~(1 << qc->dev->xfer_mode);
- } else
- retry = 0;
- }
- }
-
- return host_stat;
-}
-
-/**
- * scc_data_xfer - Transfer data by PIO
- * @dev: device for this I/O
- * @buf: data buffer
- * @buflen: buffer length
- * @rw: read/write
- *
- * Note: Original code is ata_sff_data_xfer().
- */
-
-static unsigned int scc_data_xfer (struct ata_device *dev, unsigned char *buf,
- unsigned int buflen, int rw)
-{
- struct ata_port *ap = dev->link->ap;
- unsigned int words = buflen >> 1;
- unsigned int i;
- __le16 *buf16 = (__le16 *) buf;
- void __iomem *mmio = ap->ioaddr.data_addr;
-
- /* Transfer multiple of 2 bytes */
- if (rw == READ)
- for (i = 0; i < words; i++)
- buf16[i] = cpu_to_le16(in_be32(mmio));
- else
- for (i = 0; i < words; i++)
- out_be32(mmio, le16_to_cpu(buf16[i]));
-
- /* Transfer trailing 1 byte, if any. */
- if (unlikely(buflen & 0x01)) {
- __le16 align_buf[1] = { 0 };
- unsigned char *trailing_buf = buf + buflen - 1;
-
- if (rw == READ) {
- align_buf[0] = cpu_to_le16(in_be32(mmio));
- memcpy(trailing_buf, align_buf, 1);
- } else {
- memcpy(align_buf, trailing_buf, 1);
- out_be32(mmio, le16_to_cpu(align_buf[0]));
- }
- words++;
- }
-
- return words << 1;
-}
-
-/**
- * scc_postreset - standard postreset callback
- * @ap: the target ata_port
- * @classes: classes of attached devices
- *
- * Note: Original code is ata_sff_postreset().
- */
-
-static void scc_postreset(struct ata_link *link, unsigned int *classes)
-{
- struct ata_port *ap = link->ap;
-
- DPRINTK("ENTER\n");
-
- /* is double-select really necessary? */
- if (classes[0] != ATA_DEV_NONE)
- ap->ops->sff_dev_select(ap, 1);
- if (classes[1] != ATA_DEV_NONE)
- ap->ops->sff_dev_select(ap, 0);
-
- /* bail out if no device is present */
- if (classes[0] == ATA_DEV_NONE && classes[1] == ATA_DEV_NONE) {
- DPRINTK("EXIT, no device\n");
- return;
- }
-
- /* set up device control */
- out_be32(ap->ioaddr.ctl_addr, ap->ctl);
-
- DPRINTK("EXIT\n");
-}
-
-/**
- * scc_irq_clear - Clear PCI IDE BMDMA interrupt.
- * @ap: Port associated with this ATA transaction.
- *
- * Note: Original code is ata_bmdma_irq_clear().
- */
-
-static void scc_irq_clear (struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- if (!mmio)
- return;
-
- out_be32(mmio + SCC_DMA_STATUS, in_be32(mmio + SCC_DMA_STATUS));
-}
-
-/**
- * scc_port_start - Set port up for dma.
- * @ap: Port to initialize
- *
- * Allocate space for PRD table using ata_bmdma_port_start().
- * Set PRD table address for PTERADD. (PRD Transfer End Read)
- */
-
-static int scc_port_start (struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
- int rc;
-
- rc = ata_bmdma_port_start(ap);
- if (rc)
- return rc;
-
- out_be32(mmio + SCC_DMA_PTERADD, ap->bmdma_prd_dma);
- return 0;
-}
-
-/**
- * scc_port_stop - Undo scc_port_start()
- * @ap: Port to shut down
- *
- * Reset PTERADD.
- */
-
-static void scc_port_stop (struct ata_port *ap)
-{
- void __iomem *mmio = ap->ioaddr.bmdma_addr;
-
- out_be32(mmio + SCC_DMA_PTERADD, 0);
-}
-
-static struct scsi_host_template scc_sht = {
- ATA_BMDMA_SHT(DRV_NAME),
-};
-
-static struct ata_port_operations scc_pata_ops = {
- .inherits = &ata_bmdma_port_ops,
-
- .set_piomode = scc_set_piomode,
- .set_dmamode = scc_set_dmamode,
- .mode_filter = scc_mode_filter,
-
- .sff_tf_load = scc_tf_load,
- .sff_tf_read = scc_tf_read,
- .sff_exec_command = scc_exec_command,
- .sff_check_status = scc_check_status,
- .sff_check_altstatus = scc_check_altstatus,
- .sff_dev_select = scc_dev_select,
- .sff_set_devctl = scc_set_devctl,
-
- .bmdma_setup = scc_bmdma_setup,
- .bmdma_start = scc_bmdma_start,
- .bmdma_stop = scc_bmdma_stop,
- .bmdma_status = scc_bmdma_status,
- .sff_data_xfer = scc_data_xfer,
-
- .cable_detect = ata_cable_80wire,
- .softreset = scc_softreset,
- .postreset = scc_postreset,
-
- .sff_irq_clear = scc_irq_clear,
-
- .port_start = scc_port_start,
- .port_stop = scc_port_stop,
-};
-
-static struct ata_port_info scc_port_info[] = {
- {
- .flags = ATA_FLAG_SLAVE_POSS,
- .pio_mask = ATA_PIO4,
- /* No MWDMA */
- .udma_mask = ATA_UDMA6,
- .port_ops = &scc_pata_ops,
- },
-};
-
-/**
- * scc_reset_controller - initialize SCC PATA controller.
- */
-
-static int scc_reset_controller(struct ata_host *host)
-{
- void __iomem *ctrl_base = host->iomap[SCC_CTRL_BAR];
- void __iomem *bmid_base = host->iomap[SCC_BMID_BAR];
- void __iomem *cckctrl_port = ctrl_base + SCC_CTL_CCKCTRL;
- void __iomem *mode_port = ctrl_base + SCC_CTL_MODEREG;
- void __iomem *ecmode_port = ctrl_base + SCC_CTL_ECMODE;
- void __iomem *intmask_port = bmid_base + SCC_DMA_INTMASK;
- void __iomem *dmastatus_port = bmid_base + SCC_DMA_STATUS;
- u32 reg = 0;
-
- out_be32(cckctrl_port, reg);
- reg |= CCKCTRL_ATACLKOEN;
- out_be32(cckctrl_port, reg);
- reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
- out_be32(cckctrl_port, reg);
- reg |= CCKCTRL_CRST;
- out_be32(cckctrl_port, reg);
-
- for (;;) {
- reg = in_be32(cckctrl_port);
- if (reg & CCKCTRL_CRST)
- break;
- udelay(5000);
- }
-
- reg |= CCKCTRL_ATARESET;
- out_be32(cckctrl_port, reg);
- out_be32(ecmode_port, ECMODE_VALUE);
- out_be32(mode_port, MODE_JCUSFEN);
- out_be32(intmask_port, INTMASK_MSK);
-
- if (in_be32(dmastatus_port) & QCHSD_STPDIAG) {
- printk(KERN_WARNING "%s: failed to detect 80c cable. (PDIAG# is high)\n", DRV_NAME);
- return -EIO;
- }
-
- return 0;
-}
-
-/**
- * scc_setup_ports - initialize ioaddr with SCC PATA port offsets.
- * @ioaddr: IO address structure to be initialized
- * @base: base address of BMID region
- */
-
-static void scc_setup_ports (struct ata_ioports *ioaddr, void __iomem *base)
-{
- ioaddr->cmd_addr = base + SCC_REG_CMD_ADDR;
- ioaddr->altstatus_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
- ioaddr->ctl_addr = ioaddr->cmd_addr + SCC_REG_ALTSTATUS;
- ioaddr->bmdma_addr = base;
- ioaddr->data_addr = ioaddr->cmd_addr + SCC_REG_DATA;
- ioaddr->error_addr = ioaddr->cmd_addr + SCC_REG_ERR;
- ioaddr->feature_addr = ioaddr->cmd_addr + SCC_REG_FEATURE;
- ioaddr->nsect_addr = ioaddr->cmd_addr + SCC_REG_NSECT;
- ioaddr->lbal_addr = ioaddr->cmd_addr + SCC_REG_LBAL;
- ioaddr->lbam_addr = ioaddr->cmd_addr + SCC_REG_LBAM;
- ioaddr->lbah_addr = ioaddr->cmd_addr + SCC_REG_LBAH;
- ioaddr->device_addr = ioaddr->cmd_addr + SCC_REG_DEVICE;
- ioaddr->status_addr = ioaddr->cmd_addr + SCC_REG_STATUS;
- ioaddr->command_addr = ioaddr->cmd_addr + SCC_REG_CMD;
-}
-
-static int scc_host_init(struct ata_host *host)
-{
- struct pci_dev *pdev = to_pci_dev(host->dev);
- int rc;
-
- rc = scc_reset_controller(host);
- if (rc)
- return rc;
-
- rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
- if (rc)
- return rc;
- rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
- if (rc)
- return rc;
-
- scc_setup_ports(&host->ports[0]->ioaddr, host->iomap[SCC_BMID_BAR]);
-
- pci_set_master(pdev);
-
- return 0;
-}
-
-/**
- * scc_init_one - Register SCC PATA device with kernel services
- * @pdev: PCI device to register
- * @ent: Entry in scc_pci_tbl matching with @pdev
- *
- * LOCKING:
- * Inherited from PCI layer (may sleep).
- *
- * RETURNS:
- * Zero on success, or -ERRNO value.
- */
-
-static int scc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
-{
- unsigned int board_idx = (unsigned int) ent->driver_data;
- const struct ata_port_info *ppi[] = { &scc_port_info[board_idx], NULL };
- struct ata_host *host;
- int rc;
-
- ata_print_version_once(&pdev->dev, DRV_VERSION);
-
- host = ata_host_alloc_pinfo(&pdev->dev, ppi, 1);
- if (!host)
- return -ENOMEM;
-
- rc = pcim_enable_device(pdev);
- if (rc)
- return rc;
-
- rc = pcim_iomap_regions(pdev, (1 << SCC_CTRL_BAR) | (1 << SCC_BMID_BAR), DRV_NAME);
- if (rc == -EBUSY)
- pcim_pin_device(pdev);
- if (rc)
- return rc;
- host->iomap = pcim_iomap_table(pdev);
-
- ata_port_pbar_desc(host->ports[0], SCC_CTRL_BAR, -1, "ctrl");
- ata_port_pbar_desc(host->ports[0], SCC_BMID_BAR, -1, "bmid");
-
- rc = scc_host_init(host);
- if (rc)
- return rc;
-
- return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
- IRQF_SHARED, &scc_sht);
-}
-
-static struct pci_driver scc_pci_driver = {
- .name = DRV_NAME,
- .id_table = scc_pci_tbl,
- .probe = scc_init_one,
- .remove = ata_pci_remove_one,
-#ifdef CONFIG_PM_SLEEP
- .suspend = ata_pci_device_suspend,
- .resume = ata_pci_device_resume,
-#endif
-};
-
-module_pci_driver(scc_pci_driver);
-
-MODULE_AUTHOR("Toshiba corp");
-MODULE_DESCRIPTION("SCSI low-level driver for Toshiba SCC PATA controller");
-MODULE_LICENSE("GPL");
-MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
-MODULE_VERSION(DRV_VERSION);
page_code = GET_INQ_PAGE_CODE(cmd);
alloc_len = GET_INQ_ALLOC_LENGTH(cmd);
- inq_response = kmalloc(alloc_len, GFP_KERNEL);
+ inq_response = kmalloc(max(alloc_len, STANDARD_INQUIRY_LENGTH),
+ GFP_KERNEL);
if (inq_response == NULL) {
res = -ENOMEM;
goto out_mem;
{ USB_DEVICE(0x04CA, 0x3007) },
{ USB_DEVICE(0x04CA, 0x3008) },
{ USB_DEVICE(0x04CA, 0x300b) },
+ { USB_DEVICE(0x04CA, 0x300f) },
{ USB_DEVICE(0x04CA, 0x3010) },
{ USB_DEVICE(0x0930, 0x0219) },
{ USB_DEVICE(0x0930, 0x0220) },
{ USB_DEVICE(0x0cf3, 0xe003) },
{ USB_DEVICE(0x0CF3, 0xE004) },
{ USB_DEVICE(0x0CF3, 0xE005) },
+ { USB_DEVICE(0x0CF3, 0xE006) },
{ USB_DEVICE(0x13d3, 0x3362) },
{ USB_DEVICE(0x13d3, 0x3375) },
{ USB_DEVICE(0x13d3, 0x3393) },
{ USB_DEVICE(0x04ca, 0x3007), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3008), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x300b), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x04ca, 0x300f), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3010), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0220), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0CF3, 0x817a), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe005), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x0cf3, 0xe006), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe003), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
iobase = info->p_dev->resource[0]->start;
avail = bt3c_read(iobase, 0x7006);
- //printk("bt3c_cs: receiving %d bytes\n", avail);
bt3c_address(iobase, 0x7480);
while (size < avail) {
bt_cb(info->rx_skb)->pkt_type = inb(iobase + DATA_L);
inb(iobase + DATA_H);
- //printk("bt3c: PACKET_TYPE=%02x\n", bt_cb(info->rx_skb)->pkt_type);
switch (bt_cb(info->rx_skb)->pkt_type) {
if (stat & 0x0001)
bt3c_receive(info);
if (stat & 0x0002) {
- //BT_ERR("Ack (stat=0x%04x)", stat);
clear_bit(XMIT_SENDING, &(info->tx_state));
bt3c_write_wakeup(info);
}
}
EXPORT_SYMBOL_GPL(btbcm_set_bdaddr);
+int btbcm_patchram(struct hci_dev *hdev, const char *firmware)
+{
+ const struct hci_command_hdr *cmd;
+ const struct firmware *fw;
+ const u8 *fw_ptr;
+ size_t fw_size;
+ struct sk_buff *skb;
+ u16 opcode;
+ int err;
+
+ err = request_firmware(&fw, firmware, &hdev->dev);
+ if (err < 0) {
+ BT_INFO("%s: BCM: Patch %s not found", hdev->name, firmware);
+ return err;
+ }
+
+ /* Start Download */
+ skb = __hci_cmd_sync(hdev, 0xfc2e, 0, NULL, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ BT_ERR("%s: BCM: Download Minidrv command failed (%d)",
+ hdev->name, err);
+ goto done;
+ }
+ kfree_skb(skb);
+
+ /* 50 msec delay after Download Minidrv completes */
+ msleep(50);
+
+ fw_ptr = fw->data;
+ fw_size = fw->size;
+
+ while (fw_size >= sizeof(*cmd)) {
+ const u8 *cmd_param;
+
+ cmd = (struct hci_command_hdr *)fw_ptr;
+ fw_ptr += sizeof(*cmd);
+ fw_size -= sizeof(*cmd);
+
+ if (fw_size < cmd->plen) {
+ BT_ERR("%s: BCM: Patch %s is corrupted", hdev->name,
+ firmware);
+ err = -EINVAL;
+ goto done;
+ }
+
+ cmd_param = fw_ptr;
+ fw_ptr += cmd->plen;
+ fw_size -= cmd->plen;
+
+ opcode = le16_to_cpu(cmd->opcode);
+
+ skb = __hci_cmd_sync(hdev, opcode, cmd->plen, cmd_param,
+ HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ BT_ERR("%s: BCM: Patch command %04x failed (%d)",
+ hdev->name, opcode, err);
+ goto done;
+ }
+ kfree_skb(skb);
+ }
+
+ /* 250 msec delay after Launch Ram completes */
+ msleep(250);
+
+done:
+ release_firmware(fw);
+ return err;
+}
+EXPORT_SYMBOL(btbcm_patchram);
+
static int btbcm_reset(struct hci_dev *hdev)
{
struct sk_buff *skb;
int btbcm_setup_patchram(struct hci_dev *hdev)
{
- const struct hci_command_hdr *cmd;
- const struct firmware *fw;
- const u8 *fw_ptr;
- size_t fw_size;
char fw_name[64];
- u16 opcode, subver, rev, pid, vid;
+ u16 subver, rev, pid, vid;
const char *hw_name = NULL;
struct sk_buff *skb;
struct hci_rp_read_local_version *ver;
hw_name ? : "BCM", (subver & 0x7000) >> 13,
(subver & 0x1f00) >> 8, (subver & 0x00ff), rev & 0x0fff);
- err = request_firmware(&fw, fw_name, &hdev->dev);
- if (err < 0) {
- BT_INFO("%s: BCM: patch %s not found", hdev->name, fw_name);
+ err = btbcm_patchram(hdev, fw_name);
+ if (err == -ENOENT)
return 0;
- }
-
- /* Start Download */
- skb = __hci_cmd_sync(hdev, 0xfc2e, 0, NULL, HCI_INIT_TIMEOUT);
- if (IS_ERR(skb)) {
- err = PTR_ERR(skb);
- BT_ERR("%s: BCM: Download Minidrv command failed (%d)",
- hdev->name, err);
- goto reset;
- }
- kfree_skb(skb);
-
- /* 50 msec delay after Download Minidrv completes */
- msleep(50);
-
- fw_ptr = fw->data;
- fw_size = fw->size;
-
- while (fw_size >= sizeof(*cmd)) {
- const u8 *cmd_param;
-
- cmd = (struct hci_command_hdr *)fw_ptr;
- fw_ptr += sizeof(*cmd);
- fw_size -= sizeof(*cmd);
-
- if (fw_size < cmd->plen) {
- BT_ERR("%s: BCM: patch %s is corrupted", hdev->name,
- fw_name);
- err = -EINVAL;
- goto reset;
- }
- cmd_param = fw_ptr;
- fw_ptr += cmd->plen;
- fw_size -= cmd->plen;
-
- opcode = le16_to_cpu(cmd->opcode);
-
- skb = __hci_cmd_sync(hdev, opcode, cmd->plen, cmd_param,
- HCI_INIT_TIMEOUT);
- if (IS_ERR(skb)) {
- err = PTR_ERR(skb);
- BT_ERR("%s: BCM: patch command %04x failed (%d)",
- hdev->name, opcode, err);
- goto reset;
- }
- kfree_skb(skb);
- }
-
- /* 250 msec delay after Launch Ram completes */
- msleep(250);
-
-reset:
/* Reset */
err = btbcm_reset(hdev);
if (err)
- goto done;
+ return err;
/* Read Local Version Info */
skb = btbcm_read_local_version(hdev);
- if (IS_ERR(skb)) {
- err = PTR_ERR(skb);
- goto done;
- }
+ if (IS_ERR(skb))
+ return PTR_ERR(skb);
ver = (struct hci_rp_read_local_version *)skb->data;
rev = le16_to_cpu(ver->hci_rev);
set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
-done:
- release_firmware(fw);
-
- return err;
+ return 0;
}
EXPORT_SYMBOL_GPL(btbcm_setup_patchram);
int btbcm_check_bdaddr(struct hci_dev *hdev);
int btbcm_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr);
+int btbcm_patchram(struct hci_dev *hdev, const char *firmware);
int btbcm_setup_patchram(struct hci_dev *hdev);
int btbcm_setup_apple(struct hci_dev *hdev);
return -EOPNOTSUPP;
}
+static inline int btbcm_patchram(struct hci_dev *hdev, const char *firmware)
+{
+ return -EOPNOTSUPP;
+}
+
static inline int btbcm_setup_patchram(struct hci_dev *hdev)
{
return 0;
#include <linux/module.h>
#include <linux/usb.h>
#include <linux/firmware.h>
+#include <asm/unaligned.h>
#include <net/bluetooth/bluetooth.h>
#include <net/bluetooth/hci_core.h>
#define BTUSB_AMP 0x4000
#define BTUSB_QCA_ROME 0x8000
#define BTUSB_BCM_APPLE 0x10000
+#define BTUSB_REALTEK 0x20000
static const struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
{ USB_DEVICE(0x04ca, 0x3007), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3008), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x300b), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x04ca, 0x300f), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x04ca, 0x3010), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0930, 0x0220), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe003), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0cf3, 0xe005), .driver_info = BTUSB_ATH3012 },
+ { USB_DEVICE(0x0cf3, 0xe006), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x13d3, 0x3393), .driver_info = BTUSB_ATH3012 },
{ USB_DEVICE(0x0489, 0xe03c), .driver_info = BTUSB_ATH3012 },
/* QCA ROME chipset */
+ { USB_DEVICE(0x0cf3, 0xe007), .driver_info = BTUSB_QCA_ROME },
{ USB_DEVICE(0x0cf3, 0xe300), .driver_info = BTUSB_QCA_ROME },
{ USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME },
{ USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
.driver_info = BTUSB_IGNORE },
+ /* Realtek Bluetooth devices */
+ { USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
+ .driver_info = BTUSB_REALTEK },
+
+ /* Additional Realtek 8723AE Bluetooth devices */
+ { USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },
+
+ /* Additional Realtek 8723BE Bluetooth devices */
+ { USB_DEVICE(0x0489, 0xe085), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x0489, 0xe08b), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3410), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3416), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3459), .driver_info = BTUSB_REALTEK },
+
+ /* Additional Realtek 8821AE Bluetooth devices */
+ { USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3414), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3458), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3461), .driver_info = BTUSB_REALTEK },
+ { USB_DEVICE(0x13d3, 0x3462), .driver_info = BTUSB_REALTEK },
+
{ } /* Terminating entry */
};
*/
if (data->setup_on_usb) {
err = data->setup_on_usb(hdev);
- if (err <0)
+ if (err < 0)
return err;
}
return ret;
}
+#define RTL_FRAG_LEN 252
+
+struct rtl_download_cmd {
+ __u8 index;
+ __u8 data[RTL_FRAG_LEN];
+} __packed;
+
+struct rtl_download_response {
+ __u8 status;
+ __u8 index;
+} __packed;
+
+struct rtl_rom_version_evt {
+ __u8 status;
+ __u8 version;
+} __packed;
+
+struct rtl_epatch_header {
+ __u8 signature[8];
+ __le32 fw_version;
+ __le16 num_patches;
+} __packed;
+
+#define RTL_EPATCH_SIGNATURE "Realtech"
+#define RTL_ROM_LMP_3499 0x3499
+#define RTL_ROM_LMP_8723A 0x1200
+#define RTL_ROM_LMP_8723B 0x8723
+#define RTL_ROM_LMP_8821A 0x8821
+#define RTL_ROM_LMP_8761A 0x8761
+
+static int rtl_read_rom_version(struct hci_dev *hdev, u8 *version)
+{
+ struct rtl_rom_version_evt *rom_version;
+ struct sk_buff *skb;
+ int ret;
+
+ /* Read RTL ROM version command */
+ skb = __hci_cmd_sync(hdev, 0xfc6d, 0, NULL, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s: Read ROM version failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ return PTR_ERR(skb);
+ }
+
+ if (skb->len != sizeof(*rom_version)) {
+ BT_ERR("%s: RTL version event length mismatch", hdev->name);
+ kfree_skb(skb);
+ return -EIO;
+ }
+
+ rom_version = (struct rtl_rom_version_evt *)skb->data;
+ BT_INFO("%s: rom_version status=%x version=%x",
+ hdev->name, rom_version->status, rom_version->version);
+
+ ret = rom_version->status;
+ if (ret == 0)
+ *version = rom_version->version;
+
+ kfree_skb(skb);
+ return ret;
+}
+
+static int rtl8723b_parse_firmware(struct hci_dev *hdev, u16 lmp_subver,
+ const struct firmware *fw,
+ unsigned char **_buf)
+{
+ const u8 extension_sig[] = { 0x51, 0x04, 0xfd, 0x77 };
+ struct rtl_epatch_header *epatch_info;
+ unsigned char *buf;
+ int i, ret, len;
+ size_t min_size;
+ u8 opcode, length, data, rom_version = 0;
+ int project_id = -1;
+ const unsigned char *fwptr, *chip_id_base;
+ const unsigned char *patch_length_base, *patch_offset_base;
+ u32 patch_offset = 0;
+ u16 patch_length, num_patches;
+ const u16 project_id_to_lmp_subver[] = {
+ RTL_ROM_LMP_8723A,
+ RTL_ROM_LMP_8723B,
+ RTL_ROM_LMP_8821A,
+ RTL_ROM_LMP_8761A
+ };
+
+ ret = rtl_read_rom_version(hdev, &rom_version);
+ if (ret)
+ return -bt_to_errno(ret);
+
+ min_size = sizeof(struct rtl_epatch_header) + sizeof(extension_sig) + 3;
+ if (fw->size < min_size)
+ return -EINVAL;
+
+ fwptr = fw->data + fw->size - sizeof(extension_sig);
+ if (memcmp(fwptr, extension_sig, sizeof(extension_sig)) != 0) {
+ BT_ERR("%s: extension section signature mismatch", hdev->name);
+ return -EINVAL;
+ }
+
+ /* Loop from the end of the firmware parsing instructions, until
+ * we find an instruction that identifies the "project ID" for the
+ * hardware supported by this firwmare file.
+ * Once we have that, we double-check that that project_id is suitable
+ * for the hardware we are working with.
+ */
+ while (fwptr >= fw->data + (sizeof(struct rtl_epatch_header) + 3)) {
+ opcode = *--fwptr;
+ length = *--fwptr;
+ data = *--fwptr;
+
+ BT_DBG("check op=%x len=%x data=%x", opcode, length, data);
+
+ if (opcode == 0xff) /* EOF */
+ break;
+
+ if (length == 0) {
+ BT_ERR("%s: found instruction with length 0",
+ hdev->name);
+ return -EINVAL;
+ }
+
+ if (opcode == 0 && length == 1) {
+ project_id = data;
+ break;
+ }
+
+ fwptr -= length;
+ }
+
+ if (project_id < 0) {
+ BT_ERR("%s: failed to find version instruction", hdev->name);
+ return -EINVAL;
+ }
+
+ if (project_id >= ARRAY_SIZE(project_id_to_lmp_subver)) {
+ BT_ERR("%s: unknown project id %d", hdev->name, project_id);
+ return -EINVAL;
+ }
+
+ if (lmp_subver != project_id_to_lmp_subver[project_id]) {
+ BT_ERR("%s: firmware is for %x but this is a %x", hdev->name,
+ project_id_to_lmp_subver[project_id], lmp_subver);
+ return -EINVAL;
+ }
+
+ epatch_info = (struct rtl_epatch_header *)fw->data;
+ if (memcmp(epatch_info->signature, RTL_EPATCH_SIGNATURE, 8) != 0) {
+ BT_ERR("%s: bad EPATCH signature", hdev->name);
+ return -EINVAL;
+ }
+
+ num_patches = le16_to_cpu(epatch_info->num_patches);
+ BT_DBG("fw_version=%x, num_patches=%d",
+ le32_to_cpu(epatch_info->fw_version), num_patches);
+
+ /* After the rtl_epatch_header there is a funky patch metadata section.
+ * Assuming 2 patches, the layout is:
+ * ChipID1 ChipID2 PatchLength1 PatchLength2 PatchOffset1 PatchOffset2
+ *
+ * Find the right patch for this chip.
+ */
+ min_size += 8 * num_patches;
+ if (fw->size < min_size)
+ return -EINVAL;
+
+ chip_id_base = fw->data + sizeof(struct rtl_epatch_header);
+ patch_length_base = chip_id_base + (sizeof(u16) * num_patches);
+ patch_offset_base = patch_length_base + (sizeof(u16) * num_patches);
+ for (i = 0; i < num_patches; i++) {
+ u16 chip_id = get_unaligned_le16(chip_id_base +
+ (i * sizeof(u16)));
+ if (chip_id == rom_version + 1) {
+ patch_length = get_unaligned_le16(patch_length_base +
+ (i * sizeof(u16)));
+ patch_offset = get_unaligned_le32(patch_offset_base +
+ (i * sizeof(u32)));
+ break;
+ }
+ }
+
+ if (!patch_offset) {
+ BT_ERR("%s: didn't find patch for chip id %d",
+ hdev->name, rom_version);
+ return -EINVAL;
+ }
+
+ BT_DBG("length=%x offset=%x index %d", patch_length, patch_offset, i);
+ min_size = patch_offset + patch_length;
+ if (fw->size < min_size)
+ return -EINVAL;
+
+ /* Copy the firmware into a new buffer and write the version at
+ * the end.
+ */
+ len = patch_length;
+ buf = kmemdup(fw->data + patch_offset, patch_length, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ memcpy(buf + patch_length - 4, &epatch_info->fw_version, 4);
+
+ *_buf = buf;
+ return len;
+}
+
+static int rtl_download_firmware(struct hci_dev *hdev,
+ const unsigned char *data, int fw_len)
+{
+ struct rtl_download_cmd *dl_cmd;
+ int frag_num = fw_len / RTL_FRAG_LEN + 1;
+ int frag_len = RTL_FRAG_LEN;
+ int ret = 0;
+ int i;
+
+ dl_cmd = kmalloc(sizeof(struct rtl_download_cmd), GFP_KERNEL);
+ if (!dl_cmd)
+ return -ENOMEM;
+
+ for (i = 0; i < frag_num; i++) {
+ struct rtl_download_response *dl_resp;
+ struct sk_buff *skb;
+
+ BT_DBG("download fw (%d/%d)", i, frag_num);
+
+ dl_cmd->index = i;
+ if (i == (frag_num - 1)) {
+ dl_cmd->index |= 0x80; /* data end */
+ frag_len = fw_len % RTL_FRAG_LEN;
+ }
+ memcpy(dl_cmd->data, data, frag_len);
+
+ /* Send download command */
+ skb = __hci_cmd_sync(hdev, 0xfc20, frag_len + 1, dl_cmd,
+ HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ BT_ERR("%s: download fw command failed (%ld)",
+ hdev->name, PTR_ERR(skb));
+ ret = -PTR_ERR(skb);
+ goto out;
+ }
+
+ if (skb->len != sizeof(*dl_resp)) {
+ BT_ERR("%s: download fw event length mismatch",
+ hdev->name);
+ kfree_skb(skb);
+ ret = -EIO;
+ goto out;
+ }
+
+ dl_resp = (struct rtl_download_response *)skb->data;
+ if (dl_resp->status != 0) {
+ kfree_skb(skb);
+ ret = bt_to_errno(dl_resp->status);
+ goto out;
+ }
+
+ kfree_skb(skb);
+ data += RTL_FRAG_LEN;
+ }
+
+out:
+ kfree(dl_cmd);
+ return ret;
+}
+
+static int btusb_setup_rtl8723a(struct hci_dev *hdev)
+{
+ struct btusb_data *data = dev_get_drvdata(&hdev->dev);
+ struct usb_device *udev = interface_to_usbdev(data->intf);
+ const struct firmware *fw;
+ int ret;
+
+ BT_INFO("%s: rtl: loading rtl_bt/rtl8723a_fw.bin", hdev->name);
+ ret = request_firmware(&fw, "rtl_bt/rtl8723a_fw.bin", &udev->dev);
+ if (ret < 0) {
+ BT_ERR("%s: Failed to load rtl_bt/rtl8723a_fw.bin", hdev->name);
+ return ret;
+ }
+
+ if (fw->size < 8) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* Check that the firmware doesn't have the epatch signature
+ * (which is only for RTL8723B and newer).
+ */
+ if (!memcmp(fw->data, RTL_EPATCH_SIGNATURE, 8)) {
+ BT_ERR("%s: unexpected EPATCH signature!", hdev->name);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = rtl_download_firmware(hdev, fw->data, fw->size);
+
+out:
+ release_firmware(fw);
+ return ret;
+}
+
+static int btusb_setup_rtl8723b(struct hci_dev *hdev, u16 lmp_subver,
+ const char *fw_name)
+{
+ struct btusb_data *data = dev_get_drvdata(&hdev->dev);
+ struct usb_device *udev = interface_to_usbdev(data->intf);
+ unsigned char *fw_data = NULL;
+ const struct firmware *fw;
+ int ret;
+
+ BT_INFO("%s: rtl: loading %s", hdev->name, fw_name);
+ ret = request_firmware(&fw, fw_name, &udev->dev);
+ if (ret < 0) {
+ BT_ERR("%s: Failed to load %s", hdev->name, fw_name);
+ return ret;
+ }
+
+ ret = rtl8723b_parse_firmware(hdev, lmp_subver, fw, &fw_data);
+ if (ret < 0)
+ goto out;
+
+ ret = rtl_download_firmware(hdev, fw_data, ret);
+ kfree(fw_data);
+ if (ret < 0)
+ goto out;
+
+out:
+ release_firmware(fw);
+ return ret;
+}
+
+static int btusb_setup_realtek(struct hci_dev *hdev)
+{
+ struct sk_buff *skb;
+ struct hci_rp_read_local_version *resp;
+ u16 lmp_subver;
+
+ skb = btusb_read_local_version(hdev);
+ if (IS_ERR(skb))
+ return -PTR_ERR(skb);
+
+ resp = (struct hci_rp_read_local_version *)skb->data;
+ BT_INFO("%s: rtl: examining hci_ver=%02x hci_rev=%04x lmp_ver=%02x "
+ "lmp_subver=%04x", hdev->name, resp->hci_ver, resp->hci_rev,
+ resp->lmp_ver, resp->lmp_subver);
+
+ lmp_subver = le16_to_cpu(resp->lmp_subver);
+ kfree_skb(skb);
+
+ /* Match a set of subver values that correspond to stock firmware,
+ * which is not compatible with standard btusb.
+ * If matched, upload an alternative firmware that does conform to
+ * standard btusb. Once that firmware is uploaded, the subver changes
+ * to a different value.
+ */
+ switch (lmp_subver) {
+ case RTL_ROM_LMP_8723A:
+ case RTL_ROM_LMP_3499:
+ return btusb_setup_rtl8723a(hdev);
+ case RTL_ROM_LMP_8723B:
+ return btusb_setup_rtl8723b(hdev, lmp_subver,
+ "rtl_bt/rtl8723b_fw.bin");
+ case RTL_ROM_LMP_8821A:
+ return btusb_setup_rtl8723b(hdev, lmp_subver,
+ "rtl_bt/rtl8821a_fw.bin");
+ case RTL_ROM_LMP_8761A:
+ return btusb_setup_rtl8723b(hdev, lmp_subver,
+ "rtl_bt/rtl8761a_fw.bin");
+ default:
+ BT_INFO("rtl: assuming no firmware upload needed.");
+ return 0;
+ }
+}
+
static const struct firmware *btusb_setup_intel_get_fw(struct hci_dev *hdev,
struct intel_version *ver)
{
int i, err;
err = btusb_qca_send_vendor_req(hdev, QCA_GET_TARGET_VERSION, &ver,
- sizeof(ver));
+ sizeof(ver));
if (err < 0)
return err;
hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
}
+ if (id->driver_info & BTUSB_REALTEK)
+ hdev->setup = btusb_setup_realtek;
+
if (id->driver_info & BTUSB_AMP) {
/* AMP controllers do not support SCO packets */
data->isoc = NULL;
hci_uart_tx_wakeup(hu);
}
-/* Initialize protocol */
static int ath_open(struct hci_uart *hu)
{
struct ath_struct *ath;
return 0;
}
-/* Flush protocol data */
-static int ath_flush(struct hci_uart *hu)
+static int ath_close(struct hci_uart *hu)
{
struct ath_struct *ath = hu->priv;
skb_queue_purge(&ath->txq);
+ kfree_skb(ath->rx_skb);
+
+ cancel_work_sync(&ath->ctxtsw);
+
+ hu->priv = NULL;
+ kfree(ath);
+
return 0;
}
-/* Close protocol */
-static int ath_close(struct hci_uart *hu)
+static int ath_flush(struct hci_uart *hu)
{
struct ath_struct *ath = hu->priv;
skb_queue_purge(&ath->txq);
- kfree_skb(ath->rx_skb);
+ return 0;
+}
- cancel_work_sync(&ath->ctxtsw);
+static int ath_set_bdaddr(struct hci_dev *hdev, const bdaddr_t *bdaddr)
+{
+ struct sk_buff *skb;
+ u8 buf[10];
+ int err;
+
+ buf[0] = 0x01;
+ buf[1] = 0x01;
+ buf[2] = 0x00;
+ buf[3] = sizeof(bdaddr_t);
+ memcpy(buf + 4, bdaddr, sizeof(bdaddr_t));
+
+ skb = __hci_cmd_sync(hdev, 0xfc0b, sizeof(buf), buf, HCI_INIT_TIMEOUT);
+ if (IS_ERR(skb)) {
+ err = PTR_ERR(skb);
+ BT_ERR("%s: Change address command failed (%d)",
+ hdev->name, err);
+ return err;
+ }
+ kfree_skb(skb);
- hu->priv = NULL;
- kfree(ath);
+ return 0;
+}
+
+static int ath_setup(struct hci_uart *hu)
+{
+ BT_DBG("hu %p", hu);
+
+ hu->hdev->set_bdaddr = ath_set_bdaddr;
return 0;
}
+static const struct h4_recv_pkt ath_recv_pkts[] = {
+ { H4_RECV_ACL, .recv = hci_recv_frame },
+ { H4_RECV_SCO, .recv = hci_recv_frame },
+ { H4_RECV_EVENT, .recv = hci_recv_frame },
+};
+
+static int ath_recv(struct hci_uart *hu, const void *data, int count)
+{
+ struct ath_struct *ath = hu->priv;
+
+ ath->rx_skb = h4_recv_buf(hu->hdev, ath->rx_skb, data, count,
+ ath_recv_pkts, ARRAY_SIZE(ath_recv_pkts));
+ if (IS_ERR(ath->rx_skb)) {
+ int err = PTR_ERR(ath->rx_skb);
+ BT_ERR("%s: Frame reassembly failed (%d)", hu->hdev->name, err);
+ return err;
+ }
+
+ return count;
+}
+
#define HCI_OP_ATH_SLEEP 0xFC04
-/* Enqueue frame for transmittion */
static int ath_enqueue(struct hci_uart *hu, struct sk_buff *skb)
{
struct ath_struct *ath = hu->priv;
return 0;
}
- /*
- * Update power management enable flag with parameters of
+ /* Update power management enable flag with parameters of
* HCI sleep enable vendor specific HCI command.
*/
if (bt_cb(skb)->pkt_type == HCI_COMMAND_PKT) {
return skb_dequeue(&ath->txq);
}
-static const struct h4_recv_pkt ath_recv_pkts[] = {
- { H4_RECV_ACL, .recv = hci_recv_frame },
- { H4_RECV_SCO, .recv = hci_recv_frame },
- { H4_RECV_EVENT, .recv = hci_recv_frame },
-};
-
-/* Recv data */
-static int ath_recv(struct hci_uart *hu, const void *data, int count)
-{
- struct ath_struct *ath = hu->priv;
-
- ath->rx_skb = h4_recv_buf(hu->hdev, ath->rx_skb, data, count,
- ath_recv_pkts, ARRAY_SIZE(ath_recv_pkts));
- if (IS_ERR(ath->rx_skb)) {
- int err = PTR_ERR(ath->rx_skb);
- BT_ERR("%s: Frame reassembly failed (%d)", hu->hdev->name, err);
- return err;
- }
-
- return count;
-}
-
static const struct hci_uart_proto athp = {
.id = HCI_UART_ATH3K,
.name = "ATH3K",
.open = ath_open,
.close = ath_close,
+ .flush = ath_flush,
+ .setup = ath_setup,
.recv = ath_recv,
.enqueue = ath_enqueue,
.dequeue = ath_dequeue,
- .flush = ath_flush,
};
int __init ath_init(void)
if (!pdata)
return -ENOMEM;
- pdata->clk_xtal = of_clk_get(np, 0);
- if (!IS_ERR(pdata->clk_xtal))
- clk_put(pdata->clk_xtal);
- pdata->clk_clkin = of_clk_get(np, 1);
- if (!IS_ERR(pdata->clk_clkin))
- clk_put(pdata->clk_clkin);
-
/*
* property silabs,pll-source : <num src>, [<..>]
* allow to selectively set pll source
i2c_set_clientdata(client, drvdata);
drvdata->client = client;
drvdata->variant = variant;
- drvdata->pxtal = pdata->clk_xtal;
- drvdata->pclkin = pdata->clk_clkin;
+ drvdata->pxtal = devm_clk_get(&client->dev, "xtal");
+ drvdata->pclkin = devm_clk_get(&client->dev, "clkin");
+
+ if (PTR_ERR(drvdata->pxtal) == -EPROBE_DEFER ||
+ PTR_ERR(drvdata->pclkin) == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+
+ /*
+ * Check for valid parent clock: VARIANT_A and VARIANT_B need XTAL,
+ * VARIANT_C can have CLKIN instead.
+ */
+ if (IS_ERR(drvdata->pxtal) &&
+ (drvdata->variant != SI5351_VARIANT_C || IS_ERR(drvdata->pclkin))) {
+ dev_err(&client->dev, "missing parent clock\n");
+ return -EINVAL;
+ }
drvdata->regmap = devm_regmap_init_i2c(client, &si5351_regmap_config);
if (IS_ERR(drvdata->regmap)) {
}
}
+ if (!IS_ERR(drvdata->pxtal))
+ clk_prepare_enable(drvdata->pxtal);
+ if (!IS_ERR(drvdata->pclkin))
+ clk_prepare_enable(drvdata->pclkin);
+
/* register xtal input clock gate */
memset(&init, 0, sizeof(init));
init.name = si5351_input_names[0];
clk = devm_clk_register(&client->dev, &drvdata->xtal);
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n", init.name);
- return PTR_ERR(clk);
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
/* register clkin input clock gate */
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
- return PTR_ERR(clk);
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
}
clk = devm_clk_register(&client->dev, &drvdata->pll[0].hw);
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n", init.name);
- return -EINVAL;
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
/* register PLLB or VXCO (Si5351B) */
clk = devm_clk_register(&client->dev, &drvdata->pll[1].hw);
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n", init.name);
- return -EINVAL;
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
/* register clk multisync and clk out divider */
num_clocks * sizeof(*drvdata->onecell.clks), GFP_KERNEL);
if (WARN_ON(!drvdata->msynth || !drvdata->clkout ||
- !drvdata->onecell.clks))
- return -ENOMEM;
+ !drvdata->onecell.clks)) {
+ ret = -ENOMEM;
+ goto err_clk;
+ }
for (n = 0; n < num_clocks; n++) {
drvdata->msynth[n].num = n;
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
- return -EINVAL;
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
}
if (IS_ERR(clk)) {
dev_err(&client->dev, "unable to register %s\n",
init.name);
- return -EINVAL;
+ ret = PTR_ERR(clk);
+ goto err_clk;
}
drvdata->onecell.clks[n] = clk;
&drvdata->onecell);
if (ret) {
dev_err(&client->dev, "unable to add clk provider\n");
- return ret;
+ goto err_clk;
}
return 0;
+
+err_clk:
+ if (!IS_ERR(drvdata->pxtal))
+ clk_disable_unprepare(drvdata->pxtal);
+ if (!IS_ERR(drvdata->pclkin))
+ clk_disable_unprepare(drvdata->pclkin);
+ return ret;
}
static const struct i2c_device_id si5351_i2c_ids[] = {
*/
if (clk->prepare_count) {
clk_core_prepare(parent);
+ flags = clk_enable_lock();
clk_core_enable(parent);
clk_core_enable(clk);
+ clk_enable_unlock(flags);
}
/* update the clk tree topology */
struct clk_core *parent,
struct clk_core *old_parent)
{
+ unsigned long flags;
+
/*
* Finish the migration of prepare state and undo the changes done
* for preventing a race with clk_enable().
*/
if (core->prepare_count) {
+ flags = clk_enable_lock();
clk_core_disable(core);
clk_core_disable(old_parent);
+ clk_enable_unlock(flags);
clk_core_unprepare(old_parent);
}
}
clk_enable_unlock(flags);
if (clk->prepare_count) {
+ flags = clk_enable_lock();
clk_core_disable(clk);
clk_core_disable(parent);
+ clk_enable_unlock(flags);
clk_core_unprepare(parent);
}
return ret;
static const struct parent_map gcc_xo_gpll0a_gpll1_gpll2a_map[] = {
{ P_XO, 0 },
{ P_GPLL0_AUX, 3 },
- { P_GPLL2_AUX, 2 },
{ P_GPLL1, 1 },
+ { P_GPLL2_AUX, 2 },
};
static const char *gcc_xo_gpll0a_gpll1_gpll2a[] = {
static const struct freq_tbl ftbl_gcc_venus0_vcodec0_clk[] = {
F(100000000, P_GPLL0, 8, 0, 0),
F(160000000, P_GPLL0, 5, 0, 0),
- F(228570000, P_GPLL0, 5, 0, 0),
+ F(228570000, P_GPLL0, 3.5, 0, 0),
{ }
};
obj-$(CONFIG_SOC_EXYNOS5260) += clk-exynos5260.o
obj-$(CONFIG_SOC_EXYNOS5410) += clk-exynos5410.o
obj-$(CONFIG_SOC_EXYNOS5420) += clk-exynos5420.o
-obj-$(CONFIG_ARCH_EXYNOS5433) += clk-exynos5433.o
+obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos5433.o
obj-$(CONFIG_SOC_EXYNOS5440) += clk-exynos5440.o
obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos-audss.o
obj-$(CONFIG_ARCH_EXYNOS) += clk-exynos-clkout.o
{ .offset = SRC_MASK_PERIC0, .value = 0x11111110, },
{ .offset = SRC_MASK_PERIC1, .value = 0x11111100, },
{ .offset = SRC_MASK_ISP, .value = 0x11111000, },
+ { .offset = GATE_BUS_TOP, .value = 0xffffffff, },
{ .offset = GATE_BUS_DISP1, .value = 0xffffffff, },
{ .offset = GATE_IP_PERIC, .value = 0xffffffff, },
};
PLL_35XX_RATE(825000000U, 275, 4, 1),
PLL_35XX_RATE(800000000U, 400, 6, 1),
PLL_35XX_RATE(733000000U, 733, 12, 1),
- PLL_35XX_RATE(700000000U, 360, 6, 1),
+ PLL_35XX_RATE(700000000U, 175, 3, 1),
PLL_35XX_RATE(667000000U, 222, 4, 1),
PLL_35XX_RATE(633000000U, 211, 4, 1),
PLL_35XX_RATE(600000000U, 500, 5, 2),
PLL_35XX_RATE(444000000U, 370, 5, 2),
PLL_35XX_RATE(420000000U, 350, 5, 2),
PLL_35XX_RATE(400000000U, 400, 6, 2),
- PLL_35XX_RATE(350000000U, 360, 6, 2),
+ PLL_35XX_RATE(350000000U, 350, 6, 2),
PLL_35XX_RATE(333000000U, 222, 4, 2),
PLL_35XX_RATE(300000000U, 500, 5, 3),
PLL_35XX_RATE(266000000U, 532, 6, 3),
PLL_35XX_RATE(200000000U, 400, 6, 3),
PLL_35XX_RATE(166000000U, 332, 6, 3),
PLL_35XX_RATE(160000000U, 320, 6, 3),
- PLL_35XX_RATE(133000000U, 552, 6, 4),
+ PLL_35XX_RATE(133000000U, 532, 6, 4),
PLL_35XX_RATE(100000000U, 400, 6, 4),
{ /* sentinel */ }
};
/* ENABLE_PCLK_MIF_SECURE_MONOTONIC_CNT */
GATE(CLK_PCLK_MONOTONIC_CNT, "pclk_monotonic_cnt", "div_aclk_mif_133",
- ENABLE_PCLK_MIF_SECURE_RTC, 0, 0, 0),
+ ENABLE_PCLK_MIF_SECURE_MONOTONIC_CNT, 0, 0, 0),
/* ENABLE_PCLK_MIF_SECURE_RTC */
GATE(CLK_PCLK_RTC, "pclk_rtc", "div_aclk_mif_133",
ENABLE_SCLK_APOLLO, 3, CLK_IGNORE_UNUSED, 0),
GATE(CLK_SCLK_HPM_APOLLO, "sclk_hpm_apollo", "div_sclk_hpm_apollo",
ENABLE_SCLK_APOLLO, 1, CLK_IGNORE_UNUSED, 0),
- GATE(CLK_SCLK_APOLLO, "sclk_apollo", "div_apollo_pll",
+ GATE(CLK_SCLK_APOLLO, "sclk_apollo", "div_apollo2",
ENABLE_SCLK_APOLLO, 0, CLK_IGNORE_UNUSED, 0),
};
#define ENABLE_PCLK_MSCL 0x0900
#define ENABLE_PCLK_MSCL_SECURE_SMMU_M2MSCALER0 0x0904
#define ENABLE_PCLK_MSCL_SECURE_SMMU_M2MSCALER1 0x0908
-#define ENABLE_PCLK_MSCL_SECURE_SMMU_JPEG 0x000c
+#define ENABLE_PCLK_MSCL_SECURE_SMMU_JPEG 0x090c
#define ENABLE_SCLK_MSCL 0x0a00
#define ENABLE_IP_MSCL0 0x0b00
#define ENABLE_IP_MSCL1 0x0b04
return PTR_ERR(info->id_gpiod);
}
+ info->edev = devm_extcon_dev_allocate(dev, usb_extcon_cable);
+ if (IS_ERR(info->edev)) {
+ dev_err(dev, "failed to allocate extcon device\n");
+ return -ENOMEM;
+ }
+
+ ret = devm_extcon_dev_register(dev, info->edev);
+ if (ret < 0) {
+ dev_err(dev, "failed to register extcon device\n");
+ return ret;
+ }
+
ret = gpiod_set_debounce(info->id_gpiod,
USB_GPIO_DEBOUNCE_MS * 1000);
if (ret < 0)
return ret;
}
- info->edev = devm_extcon_dev_allocate(dev, usb_extcon_cable);
- if (IS_ERR(info->edev)) {
- dev_err(dev, "failed to allocate extcon device\n");
- return -ENOMEM;
- }
-
- ret = devm_extcon_dev_register(dev, info->edev);
- if (ret < 0) {
- dev_err(dev, "failed to register extcon device\n");
- return ret;
- }
-
platform_set_drvdata(pdev, info);
device_init_wakeup(dev, 1);
buf += 16;
if (memcmp(buf, "_DMI_", 5) == 0 && dmi_checksum(buf, 15)) {
+ if (smbios_ver)
+ dmi_ver = smbios_ver;
+ else
+ dmi_ver = (buf[14] & 0xF0) << 4 | (buf[14] & 0x0F);
dmi_num = get_unaligned_le16(buf + 12);
dmi_len = get_unaligned_le16(buf + 6);
dmi_base = get_unaligned_le32(buf + 8);
if (dmi_walk_early(dmi_decode) == 0) {
if (smbios_ver) {
- dmi_ver = smbios_ver;
- pr_info("SMBIOS %d.%d%s present.\n",
- dmi_ver >> 8, dmi_ver & 0xFF,
- (dmi_ver < 0x0300) ? "" : ".x");
+ pr_info("SMBIOS %d.%d present.\n",
+ dmi_ver >> 8, dmi_ver & 0xFF);
} else {
- dmi_ver = (buf[14] & 0xF0) << 4 |
- (buf[14] & 0x0F);
pr_info("Legacy DMI %d.%d present.\n",
dmi_ver >> 8, dmi_ver & 0xFF);
}
= container_of(chip, struct kempld_gpio_data, chip);
struct kempld_device_data *pld = gpio->pld;
- return kempld_gpio_get_bit(pld, KEMPLD_GPIO_DIR_NUM(offset), offset);
+ return !kempld_gpio_get_bit(pld, KEMPLD_GPIO_DIR_NUM(offset), offset);
}
static int kempld_gpio_pincount(struct kempld_device_data *pld)
static LIST_HEAD(gpio_lookup_list);
LIST_HEAD(gpio_chips);
+
+static void gpiochip_free_hogs(struct gpio_chip *chip);
+static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip);
+
+
static inline void desc_set_label(struct gpio_desc *d, const char *label)
{
d->label = label;
err_remove_chip:
acpi_gpiochip_remove(chip);
+ gpiochip_free_hogs(chip);
of_gpiochip_remove(chip);
spin_lock_irqsave(&gpio_lock, flags);
list_del(&chip->list);
}
EXPORT_SYMBOL_GPL(gpiochip_add);
-/* Forward-declaration */
-static void gpiochip_irqchip_remove(struct gpio_chip *gpiochip);
-static void gpiochip_free_hogs(struct gpio_chip *chip);
-
/**
* gpiochip_remove() - unregister a gpio_chip
* @chip: the chip to unregister
static void decon_clear_channel(struct decon_context *ctx)
{
- int win, ch_enabled = 0;
+ unsigned int win, ch_enabled = 0;
DRM_DEBUG_KMS("%s\n", __FILE__);
}
}
-static struct exynos_drm_crtc_ops decon_crtc_ops = {
+static const struct exynos_drm_crtc_ops decon_crtc_ops = {
.dpms = decon_dpms,
.mode_fixup = decon_mode_fixup,
.commit = decon_commit,
#include <drm/bridge/ptn3460.h>
#include "exynos_dp_core.h"
-#include "exynos_drm_fimd.h"
#define ctx_from_connector(c) container_of(c, struct exynos_dp_device, \
connector)
}
}
- dev_err(dp->dev, "EDID Read success!\n");
+ dev_dbg(dp->dev, "EDID Read success!\n");
return 0;
}
static void exynos_dp_poweron(struct exynos_dp_device *dp)
{
+ struct exynos_drm_crtc *crtc = dp_to_crtc(dp);
+
if (dp->dpms_mode == DRM_MODE_DPMS_ON)
return;
}
}
- fimd_dp_clock_enable(dp_to_crtc(dp), true);
+ if (crtc->ops->clock_enable)
+ crtc->ops->clock_enable(dp_to_crtc(dp), true);
clk_prepare_enable(dp->clock);
exynos_dp_phy_init(dp);
static void exynos_dp_poweroff(struct exynos_dp_device *dp)
{
+ struct exynos_drm_crtc *crtc = dp_to_crtc(dp);
+
if (dp->dpms_mode != DRM_MODE_DPMS_ON)
return;
exynos_dp_phy_exit(dp);
clk_disable_unprepare(dp->clock);
- fimd_dp_clock_enable(dp_to_crtc(dp), false);
+ if (crtc->ops->clock_enable)
+ crtc->ops->clock_enable(dp_to_crtc(dp), false);
if (dp->panel) {
if (drm_panel_unprepare(dp->panel))
};
struct exynos_drm_crtc *exynos_drm_crtc_create(struct drm_device *drm_dev,
- struct drm_plane *plane,
- int pipe,
- enum exynos_drm_output_type type,
- struct exynos_drm_crtc_ops *ops,
- void *ctx)
+ struct drm_plane *plane,
+ int pipe,
+ enum exynos_drm_output_type type,
+ const struct exynos_drm_crtc_ops *ops,
+ void *ctx)
{
struct exynos_drm_crtc *exynos_crtc;
struct exynos_drm_private *private = drm_dev->dev_private;
#include "exynos_drm_drv.h"
struct exynos_drm_crtc *exynos_drm_crtc_create(struct drm_device *drm_dev,
- struct drm_plane *plane,
- int pipe,
- enum exynos_drm_output_type type,
- struct exynos_drm_crtc_ops *ops,
- void *context);
+ struct drm_plane *plane,
+ int pipe,
+ enum exynos_drm_output_type type,
+ const struct exynos_drm_crtc_ops *ops,
+ void *context);
int exynos_drm_crtc_enable_vblank(struct drm_device *dev, int pipe);
void exynos_drm_crtc_disable_vblank(struct drm_device *dev, int pipe);
void exynos_drm_crtc_finish_pageflip(struct drm_device *dev, int pipe);
* @dma_addr: array of bus(accessed by dma) address to the memory region
* allocated for a overlay.
* @zpos: order of overlay layer(z position).
- * @index_color: if using color key feature then this value would be used
- * as index color.
- * @default_win: a window to be enabled.
- * @color_key: color key on or off.
- * @local_path: in case of lcd type, local path mode on or off.
- * @transparency: transparency on or off.
- * @activated: activated or not.
* @enabled: enabled or not.
* @resume: to resume or not.
*
uint32_t pixel_format;
dma_addr_t dma_addr[MAX_FB_BUFFER];
unsigned int zpos;
- unsigned int index_color;
- bool default_win:1;
- bool color_key:1;
- bool local_path:1;
- bool transparency:1;
- bool activated:1;
bool enabled:1;
bool resume:1;
};
* @win_disable: disable hardware specific overlay.
* @te_handler: trigger to transfer video image at the tearing effect
* synchronization signal if there is a page flip request.
+ * @clock_enable: optional function enabling/disabling display domain clock,
+ * called from exynos-dp driver before powering up (with
+ * 'enable' argument as true) and after powering down (with
+ * 'enable' as false).
*/
struct exynos_drm_crtc;
struct exynos_drm_crtc_ops {
void (*win_commit)(struct exynos_drm_crtc *crtc, unsigned int zpos);
void (*win_disable)(struct exynos_drm_crtc *crtc, unsigned int zpos);
void (*te_handler)(struct exynos_drm_crtc *crtc);
+ void (*clock_enable)(struct exynos_drm_crtc *crtc, bool enable);
};
/*
unsigned int dpms;
wait_queue_head_t pending_flip_queue;
struct drm_pending_vblank_event *event;
- struct exynos_drm_crtc_ops *ops;
+ const struct exynos_drm_crtc_ops *ops;
void *ctx;
};
return &exynos_fb->fb;
}
-static u32 exynos_drm_format_num_buffers(struct drm_mode_fb_cmd2 *mode_cmd)
-{
- unsigned int cnt = 0;
-
- if (mode_cmd->pixel_format != DRM_FORMAT_NV12)
- return drm_format_num_planes(mode_cmd->pixel_format);
-
- while (cnt != MAX_FB_BUFFER) {
- if (!mode_cmd->handles[cnt])
- break;
- cnt++;
- }
-
- /*
- * check if NV12 or NV12M.
- *
- * NV12
- * handles[0] = base1, offsets[0] = 0
- * handles[1] = base1, offsets[1] = Y_size
- *
- * NV12M
- * handles[0] = base1, offsets[0] = 0
- * handles[1] = base2, offsets[1] = 0
- */
- if (cnt == 2) {
- /*
- * in case of NV12 format, offsets[1] is not 0 and
- * handles[0] is same as handles[1].
- */
- if (mode_cmd->offsets[1] &&
- mode_cmd->handles[0] == mode_cmd->handles[1])
- cnt = 1;
- }
-
- return cnt;
-}
-
static struct drm_framebuffer *
exynos_user_fb_create(struct drm_device *dev, struct drm_file *file_priv,
struct drm_mode_fb_cmd2 *mode_cmd)
drm_helper_mode_fill_fb_struct(&exynos_fb->fb, mode_cmd);
exynos_fb->exynos_gem_obj[0] = to_exynos_gem_obj(obj);
- exynos_fb->buf_cnt = exynos_drm_format_num_buffers(mode_cmd);
+ exynos_fb->buf_cnt = drm_format_num_planes(mode_cmd->pixel_format);
DRM_DEBUG_KMS("buf_cnt = %d\n", exynos_fb->buf_cnt);
#include "exynos_drm_crtc.h"
#include "exynos_drm_plane.h"
#include "exynos_drm_iommu.h"
-#include "exynos_drm_fimd.h"
/*
* FIMD stands for Fully Interactive Mobile Display and
DRM_DEBUG_KMS("vblank wait timed out.\n");
}
-static void fimd_enable_video_output(struct fimd_context *ctx, int win,
+static void fimd_enable_video_output(struct fimd_context *ctx, unsigned int win,
bool enable)
{
u32 val = readl(ctx->regs + WINCON(win));
writel(val, ctx->regs + WINCON(win));
}
-static void fimd_enable_shadow_channel_path(struct fimd_context *ctx, int win,
+static void fimd_enable_shadow_channel_path(struct fimd_context *ctx,
+ unsigned int win,
bool enable)
{
u32 val = readl(ctx->regs + SHADOWCON);
static void fimd_clear_channel(struct fimd_context *ctx)
{
- int win, ch_enabled = 0;
+ unsigned int win, ch_enabled = 0;
DRM_DEBUG_KMS("%s\n", __FILE__);
drm_handle_vblank(ctx->drm_dev, ctx->pipe);
}
-static struct exynos_drm_crtc_ops fimd_crtc_ops = {
+static void fimd_dp_clock_enable(struct exynos_drm_crtc *crtc, bool enable)
+{
+ struct fimd_context *ctx = crtc->ctx;
+ u32 val;
+
+ /*
+ * Only Exynos 5250, 5260, 5410 and 542x requires enabling DP/MIE
+ * clock. On these SoCs the bootloader may enable it but any
+ * power domain off/on will reset it to disable state.
+ */
+ if (ctx->driver_data != &exynos5_fimd_driver_data)
+ return;
+
+ val = enable ? DP_MIE_CLK_DP_ENABLE : DP_MIE_CLK_DISABLE;
+ writel(DP_MIE_CLK_DP_ENABLE, ctx->regs + DP_MIE_CLKCON);
+}
+
+static const struct exynos_drm_crtc_ops fimd_crtc_ops = {
.dpms = fimd_dpms,
.mode_fixup = fimd_mode_fixup,
.commit = fimd_commit,
.win_commit = fimd_win_commit,
.win_disable = fimd_win_disable,
.te_handler = fimd_te_handler,
+ .clock_enable = fimd_dp_clock_enable,
};
static irqreturn_t fimd_irq_handler(int irq, void *dev_id)
if (ctx->display)
exynos_drm_create_enc_conn(drm_dev, ctx->display);
- ret = fimd_iommu_attach_devices(ctx, drm_dev);
- if (ret)
- return ret;
-
- return 0;
-
+ return fimd_iommu_attach_devices(ctx, drm_dev);
}
static void fimd_unbind(struct device *dev, struct device *master,
return 0;
}
-void fimd_dp_clock_enable(struct exynos_drm_crtc *crtc, bool enable)
-{
- struct fimd_context *ctx = crtc->ctx;
- u32 val;
-
- /*
- * Only Exynos 5250, 5260, 5410 and 542x requires enabling DP/MIE
- * clock. On these SoCs the bootloader may enable it but any
- * power domain off/on will reset it to disable state.
- */
- if (ctx->driver_data != &exynos5_fimd_driver_data)
- return;
-
- val = enable ? DP_MIE_CLK_DP_ENABLE : DP_MIE_CLK_DISABLE;
- writel(DP_MIE_CLK_DP_ENABLE, ctx->regs + DP_MIE_CLKCON);
-}
-EXPORT_SYMBOL_GPL(fimd_dp_clock_enable);
-
struct platform_driver fimd_driver = {
.probe = fimd_probe,
.remove = fimd_remove,
+++ /dev/null
-/*
- * Copyright (c) 2015 Samsung Electronics Co., Ltd.
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- */
-
-#ifndef _EXYNOS_DRM_FIMD_H_
-#define _EXYNOS_DRM_FIMD_H_
-
-extern void fimd_dp_clock_enable(struct exynos_drm_crtc *crtc, bool enable);
-
-#endif /* _EXYNOS_DRM_FIMD_H_ */
return -EFAULT;
}
- exynos_plane->dma_addr[i] = buffer->dma_addr;
+ exynos_plane->dma_addr[i] = buffer->dma_addr + fb->offsets[i];
DRM_DEBUG_KMS("buffer: %d, dma_addr = 0x%lx\n",
i, (unsigned long)exynos_plane->dma_addr[i]);
return 0;
}
-static struct exynos_drm_crtc_ops vidi_crtc_ops = {
+static const struct exynos_drm_crtc_ops vidi_crtc_ops = {
.dpms = vidi_dpms,
.enable_vblank = vidi_enable_vblank,
.disable_vblank = vidi_disable_vblank,
#define MIXER_WIN_NR 3
#define MIXER_DEFAULT_WIN 0
+/* The pixelformats that are natively supported by the mixer. */
+#define MXR_FORMAT_RGB565 4
+#define MXR_FORMAT_ARGB1555 5
+#define MXR_FORMAT_ARGB4444 6
+#define MXR_FORMAT_ARGB8888 7
+
struct mixer_resources {
int irq;
void __iomem *mixer_regs;
mixer_reg_writemask(res, MXR_CFG, val, MXR_CFG_RGB_FMT_MASK);
}
-static void mixer_cfg_layer(struct mixer_context *ctx, int win, bool enable)
+static void mixer_cfg_layer(struct mixer_context *ctx, unsigned int win,
+ bool enable)
{
struct mixer_resources *res = &ctx->mixer_res;
u32 val = enable ? ~0 : 0;
struct mixer_resources *res = &ctx->mixer_res;
mixer_reg_writemask(res, MXR_STATUS, ~0, MXR_STATUS_REG_RUN);
-
- mixer_regs_dump(ctx);
}
static void mixer_stop(struct mixer_context *ctx)
while (!(mixer_reg_read(res, MXR_STATUS) & MXR_STATUS_REG_IDLE) &&
--timeout)
usleep_range(10000, 12000);
-
- mixer_regs_dump(ctx);
}
-static void vp_video_buffer(struct mixer_context *ctx, int win)
+static void vp_video_buffer(struct mixer_context *ctx, unsigned int win)
{
struct mixer_resources *res = &ctx->mixer_res;
unsigned long flags;
struct exynos_drm_plane *plane;
- unsigned int buf_num = 1;
dma_addr_t luma_addr[2], chroma_addr[2];
bool tiled_mode = false;
bool crcb_mode = false;
switch (plane->pixel_format) {
case DRM_FORMAT_NV12:
crcb_mode = false;
- buf_num = 2;
break;
- /* TODO: single buffer format NV12, NV21 */
+ case DRM_FORMAT_NV21:
+ crcb_mode = true;
+ break;
default:
- /* ignore pixel format at disable time */
- if (!plane->dma_addr[0])
- break;
-
DRM_ERROR("pixel format for vp is wrong [%d].\n",
plane->pixel_format);
return;
}
- if (buf_num == 2) {
- luma_addr[0] = plane->dma_addr[0];
- chroma_addr[0] = plane->dma_addr[1];
- } else {
- luma_addr[0] = plane->dma_addr[0];
- chroma_addr[0] = plane->dma_addr[0]
- + (plane->pitch * plane->fb_height);
- }
+ luma_addr[0] = plane->dma_addr[0];
+ chroma_addr[0] = plane->dma_addr[1];
if (plane->scan_flag & DRM_MODE_FLAG_INTERLACE) {
ctx->interlace = true;
mixer_vsync_set_update(ctx, true);
spin_unlock_irqrestore(&res->reg_slock, flags);
+ mixer_regs_dump(ctx);
vp_regs_dump(ctx);
}
return -ENOTSUPP;
}
-static void mixer_graph_buffer(struct mixer_context *ctx, int win)
+static void mixer_graph_buffer(struct mixer_context *ctx, unsigned int win)
{
struct mixer_resources *res = &ctx->mixer_res;
unsigned long flags;
plane = &ctx->planes[win];
- #define RGB565 4
- #define ARGB1555 5
- #define ARGB4444 6
- #define ARGB8888 7
+ switch (plane->pixel_format) {
+ case DRM_FORMAT_XRGB4444:
+ fmt = MXR_FORMAT_ARGB4444;
+ break;
- switch (plane->bpp) {
- case 16:
- fmt = ARGB4444;
+ case DRM_FORMAT_XRGB1555:
+ fmt = MXR_FORMAT_ARGB1555;
break;
- case 32:
- fmt = ARGB8888;
+
+ case DRM_FORMAT_RGB565:
+ fmt = MXR_FORMAT_RGB565;
+ break;
+
+ case DRM_FORMAT_XRGB8888:
+ case DRM_FORMAT_ARGB8888:
+ fmt = MXR_FORMAT_ARGB8888;
break;
+
default:
- fmt = ARGB8888;
+ DRM_DEBUG_KMS("pixelformat unsupported by mixer\n");
+ return;
}
/* check if mixer supports requested scaling setup */
mixer_vsync_set_update(ctx, true);
spin_unlock_irqrestore(&res->reg_slock, flags);
+
+ mixer_regs_dump(ctx);
}
static void vp_win_reset(struct mixer_context *ctx)
mutex_unlock(&ctx->mixer_mutex);
mixer_stop(ctx);
+ mixer_regs_dump(ctx);
mixer_window_suspend(ctx);
ctx->int_en = mixer_reg_read(res, MXR_INT_EN);
return -EINVAL;
}
-static struct exynos_drm_crtc_ops mixer_crtc_ops = {
+static const struct exynos_drm_crtc_ops mixer_crtc_ops = {
.dpms = mixer_dpms,
.enable_vblank = mixer_enable_vblank,
.disable_vblank = mixer_disable_vblank,
.has_sclk = 1,
};
-static struct platform_device_id mixer_driver_types[] = {
+static const struct platform_device_id mixer_driver_types[] = {
{
.name = "s5p-mixer",
.driver_data = (unsigned long)&exynos4210_mxr_drv_data,
intel_init_pch_refclk(dev);
drm_mode_config_reset(dev);
+ /*
+ * Interrupts have to be enabled before any batches are run. If not the
+ * GPU will hang. i915_gem_init_hw() will initiate batches to
+ * update/restore the context.
+ *
+ * Modeset enabling in intel_modeset_init_hw() also needs working
+ * interrupts.
+ */
+ intel_runtime_pm_enable_interrupts(dev_priv);
+
mutex_lock(&dev->struct_mutex);
if (i915_gem_init_hw(dev)) {
DRM_ERROR("failed to re-initialize GPU, declaring wedged!\n");
}
mutex_unlock(&dev->struct_mutex);
- /* We need working interrupts for modeset enabling ... */
- intel_runtime_pm_enable_interrupts(dev_priv);
-
intel_modeset_init_hw(dev);
spin_lock_irq(&dev_priv->irq_lock);
p->pipe_htotal = intel_crtc->config->base.adjusted_mode.crtc_htotal;
p->pixel_rate = ilk_pipe_pixel_rate(dev, crtc);
- if (crtc->primary->state->fb) {
- p->pri.enabled = true;
+ if (crtc->primary->state->fb)
p->pri.bytes_per_pixel =
crtc->primary->state->fb->bits_per_pixel / 8;
- } else {
- p->pri.enabled = false;
- p->pri.bytes_per_pixel = 0;
- }
+ else
+ p->pri.bytes_per_pixel = 4;
+
+ p->cur.bytes_per_pixel = 4;
+ /*
+ * TODO: for now, assume primary and cursor planes are always enabled.
+ * Setting them to false makes the screen flicker.
+ */
+ p->pri.enabled = true;
+ p->cur.enabled = true;
- if (crtc->cursor->state->fb) {
- p->cur.enabled = true;
- p->cur.bytes_per_pixel = 4;
- } else {
- p->cur.enabled = false;
- p->cur.bytes_per_pixel = 0;
- }
p->pri.horiz_pixels = intel_crtc->config->pipe_src_w;
p->cur.horiz_pixels = intel_crtc->base.cursor->state->crtc_w;
if (gpu->memptrs_bo) {
if (gpu->memptrs_iova)
msm_gem_put_iova(gpu->memptrs_bo, gpu->base.id);
- drm_gem_object_unreference(gpu->memptrs_bo);
+ drm_gem_object_unreference_unlocked(gpu->memptrs_bo);
}
release_firmware(gpu->pm4);
release_firmware(gpu->pfp);
goto fail;
}
+ for (i = 0; i < MSM_DSI_ENCODER_NUM; i++) {
+ encoders[i]->bridge = msm_dsi->bridge;
+ msm_dsi->encoders[i] = encoders[i];
+ }
+
msm_dsi->connector = msm_dsi_manager_connector_init(msm_dsi->id);
if (IS_ERR(msm_dsi->connector)) {
ret = PTR_ERR(msm_dsi->connector);
goto fail;
}
- for (i = 0; i < MSM_DSI_ENCODER_NUM; i++) {
- encoders[i]->bridge = msm_dsi->bridge;
- msm_dsi->encoders[i] = encoders[i];
- }
-
priv->bridges[priv->num_bridges++] = msm_dsi->bridge;
priv->connectors[priv->num_connectors++] = msm_dsi->connector;
*data = buf[1]; /* strip out dcs type */
return 1;
} else {
- pr_err("%s: read data does not match with rx_buf len %d\n",
+ pr_err("%s: read data does not match with rx_buf len %zu\n",
__func__, msg->rx_len);
return -EINVAL;
}
data[1] = buf[2];
return 2;
} else {
- pr_err("%s: read data does not match with rx_buf len %d\n",
+ pr_err("%s: read data does not match with rx_buf len %zu\n",
__func__, msg->rx_len);
return -EINVAL;
}
{
u32 *lp, *temp, data;
int i, j = 0, cnt;
- bool ack_error = false;
u32 read_cnt;
u8 reg[16];
int repeated_bytes = 0;
if (cnt > 4)
cnt = 4; /* 4 x 32 bits registers only */
- /* Calculate real read data count */
- read_cnt = dsi_read(msm_host, 0x1d4) >> 16;
-
- ack_error = (rx_byte == 4) ?
- (read_cnt == 8) : /* short pkt + 4-byte error pkt */
- (read_cnt == (pkt_size + 6 + 4)); /* long pkt+4-byte error pkt*/
-
- if (ack_error)
- read_cnt -= 4; /* Remove 4 byte error pkt */
+ if (rx_byte == 4)
+ read_cnt = 4;
+ else
+ read_cnt = pkt_size + 6;
/*
* In case of multiple reads from the panel, after the first read, there
container_of(work, struct msm_dsi_host, err_work);
u32 status = msm_host->err_work_state;
- pr_err("%s: status=%x\n", __func__, status);
+ pr_err_ratelimited("%s: status=%x\n", __func__, status);
if (status & DSI_ERR_STATE_MDP_FIFO_UNDERFLOW)
dsi_sw_reset_restore(msm_host);
case MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT:
pr_err("%s: rx ACK_ERR_PACLAGE\n", __func__);
ret = 0;
+ break;
case MIPI_DSI_RX_GENERIC_SHORT_READ_RESPONSE_1BYTE:
case MIPI_DSI_RX_DCS_SHORT_READ_RESPONSE_1BYTE:
ret = dsi_short_read1_resp(buf, msg);
struct msm_dsi *msm_dsi = dsi_mgr_get_dsi(id);
struct drm_connector *connector = NULL;
struct dsi_connector *dsi_connector;
- int ret;
+ int ret, i;
dsi_connector = devm_kzalloc(msm_dsi->dev->dev,
sizeof(*dsi_connector), GFP_KERNEL);
if (ret)
goto fail;
+ for (i = 0; i < MSM_DSI_ENCODER_NUM; i++)
+ drm_mode_connector_attach_encoder(connector,
+ msm_dsi->encoders[i]);
+
return connector;
fail:
/* msg sanity check */
if ((native && (msg->size > AUX_CMD_NATIVE_MAX)) ||
(msg->size > AUX_CMD_I2C_MAX)) {
- pr_err("%s: invalid msg: size(%d), request(%x)\n",
+ pr_err("%s: invalid msg: size(%zu), request(%x)\n",
__func__, msg->size, msg->request);
return -EINVAL;
}
*/
edp_write(aux->base + REG_EDP_AUX_TRANS_CTRL, 0);
msm_edp_aux_ctrl(aux, 1);
- pr_err("%s: aux timeout, %d\n", __func__, ret);
+ pr_err("%s: aux timeout, %zd\n", __func__, ret);
goto unlock_exit;
}
DBG("completion");
if (ret)
goto fail;
+ drm_mode_connector_attach_encoder(connector, edp->encoder);
+
return connector;
fail:
ctrl->aux = msm_edp_aux_init(dev, ctrl->base, &ctrl->drm_aux);
if (!ctrl->aux || !ctrl->drm_aux) {
pr_err("%s:failed to init aux\n", __func__);
- return ret;
+ return -ENOMEM;
}
ctrl->phy = msm_edp_phy_init(dev, ctrl->base);
if (!ctrl->phy) {
pr_err("%s:failed to init phy\n", __func__);
+ ret = -ENOMEM;
goto err_destory_aux;
}
.base = { 0x12d00, 0x12e00, 0x12f00 },
},
.intf = {
- .count = 4,
.base = { 0x12500, 0x12700, 0x12900, 0x12b00 },
- },
- .intfs = {
- [0] = INTF_eDP,
- [1] = INTF_DSI,
- [2] = INTF_DSI,
- [3] = INTF_HDMI,
+ .connect = {
+ [0] = INTF_eDP,
+ [1] = INTF_DSI,
+ [2] = INTF_DSI,
+ [3] = INTF_HDMI,
+ },
},
.max_clk = 200000000,
};
.base = { 0x12f00, 0x13000, 0x13100, 0x13200 },
},
.intf = {
- .count = 5,
.base = { 0x12500, 0x12700, 0x12900, 0x12b00, 0x12d00 },
- },
- .intfs = {
- [0] = INTF_eDP,
- [1] = INTF_DSI,
- [2] = INTF_DSI,
- [3] = INTF_HDMI,
+ .connect = {
+ [0] = INTF_eDP,
+ [1] = INTF_DSI,
+ [2] = INTF_DSI,
+ [3] = INTF_HDMI,
+ },
},
.max_clk = 320000000,
};
},
.intf = {
- .count = 1, /* INTF_1 */
- .base = { 0x6B800 },
+ .base = { 0x00000, 0x6b800 },
+ .connect = {
+ [0] = INTF_DISABLED,
+ [1] = INTF_DSI,
+ },
},
- /* TODO enable .intfs[] with [1] = INTF_DSI, once DSI is implemented */
.max_clk = 320000000,
};
#define MDP5_INTF_NUM_MAX 5
+struct mdp5_intf_block {
+ uint32_t base[MAX_BASES];
+ u32 connect[MDP5_INTF_NUM_MAX]; /* array of enum mdp5_intf_type */
+};
+
struct mdp5_cfg_hw {
char *name;
struct mdp5_sub_block dspp;
struct mdp5_sub_block ad;
struct mdp5_sub_block pp;
- struct mdp5_sub_block intf;
-
- u32 intfs[MDP5_INTF_NUM_MAX]; /* array of enum mdp5_intf_type */
+ struct mdp5_intf_block intf;
uint32_t max_clk;
};
static int get_dsi_id_from_intf(const struct mdp5_cfg_hw *hw_cfg, int intf_num)
{
- const int intf_cnt = hw_cfg->intf.count;
- const u32 *intfs = hw_cfg->intfs;
+ const enum mdp5_intf_type *intfs = hw_cfg->intf.connect;
+ const int intf_cnt = ARRAY_SIZE(hw_cfg->intf.connect);
int id = 0, i;
for (i = 0; i < intf_cnt; i++) {
struct msm_drm_private *priv = dev->dev_private;
const struct mdp5_cfg_hw *hw_cfg =
mdp5_cfg_get_hw_config(mdp5_kms->cfg);
- enum mdp5_intf_type intf_type = hw_cfg->intfs[intf_num];
+ enum mdp5_intf_type intf_type = hw_cfg->intf.connect[intf_num];
struct drm_encoder *encoder;
int ret = 0;
/* Construct encoders and modeset initialize connector devices
* for each external display interface.
*/
- for (i = 0; i < ARRAY_SIZE(hw_cfg->intfs); i++) {
+ for (i = 0; i < ARRAY_SIZE(hw_cfg->intf.connect); i++) {
ret = modeset_init_intf(mdp5_kms, i);
if (ret)
goto fail;
*/
mdp5_enable(mdp5_kms);
for (i = 0; i < MDP5_INTF_NUM_MAX; i++) {
- if (!config->hw->intf.base[i] ||
- mdp5_cfg_intf_is_virtual(config->hw->intfs[i]))
+ if (mdp5_cfg_intf_is_virtual(config->hw->intf.connect[i]) ||
+ !config->hw->intf.base[i])
continue;
mdp5_write(mdp5_kms, REG_MDP5_INTF_TIMING_ENGINE_EN(i), 0);
}
mdp5_write(mdp5_kms, REG_MDP5_PIPE_SRC2_ADDR(pipe),
msm_framebuffer_iova(fb, mdp5_kms->id, 2));
mdp5_write(mdp5_kms, REG_MDP5_PIPE_SRC3_ADDR(pipe),
- msm_framebuffer_iova(fb, mdp5_kms->id, 4));
+ msm_framebuffer_iova(fb, mdp5_kms->id, 3));
plane->fb = fb;
}
static void msm_fb_output_poll_changed(struct drm_device *dev)
{
+#ifdef CONFIG_DRM_MSM_FBDEV
struct msm_drm_private *priv = dev->dev_private;
if (priv->fbdev)
drm_fb_helper_hotplug_event(priv->fbdev);
+#endif
}
static const struct drm_mode_config_funcs mode_config_funcs = {
}
if (reglog)
- printk(KERN_DEBUG "IO:region %s %08x %08lx\n", dbgname, (u32)ptr, size);
+ printk(KERN_DEBUG "IO:region %s %p %08lx\n", dbgname, ptr, size);
return ptr;
}
void msm_writel(u32 data, void __iomem *addr)
{
if (reglog)
- printk(KERN_DEBUG "IO:W %08x %08x\n", (u32)addr, data);
+ printk(KERN_DEBUG "IO:W %p %08x\n", addr, data);
writel(data, addr);
}
{
u32 val = readl(addr);
if (reglog)
- printk(KERN_ERR "IO:R %08x %08x\n", (u32)addr, val);
+ printk(KERN_ERR "IO:R %p %08x\n", addr, val);
return val;
}
if (gpu) {
mutex_lock(&dev->struct_mutex);
gpu->funcs->pm_suspend(gpu);
- gpu->funcs->destroy(gpu);
mutex_unlock(&dev->struct_mutex);
+ gpu->funcs->destroy(gpu);
}
if (priv->vram.paddr) {
const struct of_device_id *match;
match = of_match_node(match_types, dev->of_node);
if (match)
- return (int)match->data;
+ return (int)(unsigned long)match->data;
#endif
return 4;
}
if (ret)
return ret;
size = r.end - r.start;
- DRM_INFO("using VRAM carveout: %lx@%08x\n", size, r.start);
+ DRM_INFO("using VRAM carveout: %lx@%pa\n", size, &r.start);
} else
#endif
drm_mode_config_init(dev);
- ret = msm_init_vram(dev);
- if (ret)
- goto fail;
-
platform_set_drvdata(pdev, dev);
/* Bind all our sub-components: */
if (ret)
return ret;
+ ret = msm_init_vram(dev);
+ if (ret)
+ goto fail;
+
switch (get_mdp_ver(pdev)) {
case 4:
kms = mdp4_kms_init(dev);
static void msm_lastclose(struct drm_device *dev)
{
+#ifdef CONFIG_DRM_MSM_FBDEV
struct msm_drm_private *priv = dev->dev_private;
if (priv->fbdev)
drm_fb_helper_restore_fbdev_mode_unlocked(priv->fbdev);
+#endif
}
static irqreturn_t msm_irq(int irq, void *arg)
{
struct msm_drm_private *priv = dev->dev_private;
struct msm_kms *kms = priv->kms;
- struct msm_framebuffer *msm_fb;
- struct drm_framebuffer *fb = NULL;
+ struct msm_framebuffer *msm_fb = NULL;
+ struct drm_framebuffer *fb;
const struct msm_format *format;
int ret, i, n;
unsigned int hsub, vsub;
return fb;
fail:
- if (fb)
- msm_framebuffer_destroy(fb);
+ kfree(msm_fb);
return ERR_PTR(ret);
}
uint64_t off = drm_vma_node_start(&obj->vma_node);
WARN_ON(!mutex_is_locked(&dev->struct_mutex));
- seq_printf(m, "%08x: %c(r=%u,w=%u) %2d (%2d) %08llx %p %d\n",
+ seq_printf(m, "%08x: %c(r=%u,w=%u) %2d (%2d) %08llx %p %zu\n",
msm_obj->flags, is_active(msm_obj) ? 'A' : 'I',
msm_obj->read_fence, msm_obj->write_fence,
obj->name, obj->refcount.refcount.counter,
u32 pa = sg_phys(sg) - sg->offset;
size_t bytes = sg->length + sg->offset;
- VERB("map[%d]: %08x %08x(%x)", i, iova, pa, bytes);
+ VERB("map[%d]: %08x %08x(%zx)", i, iova, pa, bytes);
ret = iommu_map(domain, da, pa, bytes, prot);
if (ret)
if (unmapped < bytes)
return unmapped;
- VERB("unmap[%d]: %08x(%x)", i, iova, bytes);
+ VERB("unmap[%d]: %08x(%zx)", i, iova, bytes);
BUG_ON(!PAGE_ALIGNED(bytes));
void msm_ringbuffer_destroy(struct msm_ringbuffer *ring)
{
if (ring->bo)
- drm_gem_object_unreference(ring->bo);
+ drm_gem_object_unreference_unlocked(ring->bo);
kfree(ring);
}
{
struct radeon_connector_atom_dig *dig_connector = radeon_connector->con_priv;
u8 msg[DP_DPCD_SIZE];
- int ret;
+ int ret, i;
- ret = drm_dp_dpcd_read(&radeon_connector->ddc_bus->aux, DP_DPCD_REV, msg,
- DP_DPCD_SIZE);
- if (ret > 0) {
- memcpy(dig_connector->dpcd, msg, DP_DPCD_SIZE);
+ for (i = 0; i < 7; i++) {
+ ret = drm_dp_dpcd_read(&radeon_connector->ddc_bus->aux, DP_DPCD_REV, msg,
+ DP_DPCD_SIZE);
+ if (ret == DP_DPCD_SIZE) {
+ memcpy(dig_connector->dpcd, msg, DP_DPCD_SIZE);
- DRM_DEBUG_KMS("DPCD: %*ph\n", (int)sizeof(dig_connector->dpcd),
- dig_connector->dpcd);
+ DRM_DEBUG_KMS("DPCD: %*ph\n", (int)sizeof(dig_connector->dpcd),
+ dig_connector->dpcd);
- radeon_dp_probe_oui(radeon_connector);
+ radeon_dp_probe_oui(radeon_connector);
- return true;
+ return true;
+ }
}
dig_connector->dpcd[0] = 0;
return false;
L2_CACHE_BIGK_FRAGMENT_SIZE(4));
/* setup context0 */
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR,
(u32)(rdev->dummy_page.addr >> 12));
/* restore context1-15 */
/* set vm size, must be a multiple of 4 */
WREG32(VM_CONTEXT1_PAGE_TABLE_START_ADDR, 0);
- WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn);
+ WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn - 1);
for (i = 1; i < 16; i++) {
if (i < 8)
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
WREG32(MC_VM_MB_L1_TLB2_CNTL, tmp);
WREG32(MC_VM_MB_L1_TLB3_CNTL, tmp);
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_CNTL, ENABLE_CONTEXT | PAGE_TABLE_DEPTH(0) |
RANGE_PROTECTION_FAULT_ENABLE_DEFAULT);
L2_CACHE_BIGK_FRAGMENT_SIZE(6));
/* setup context0 */
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR,
(u32)(rdev->dummy_page.addr >> 12));
*/
for (i = 1; i < 8; i++) {
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR + (i << 2), 0);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR + (i << 2), rdev->vm_manager.max_pfn);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR + (i << 2),
+ rdev->vm_manager.max_pfn - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR + (i << 2),
rdev->vm_manager.saved_table_addr[i]);
}
WREG32(MC_VM_L1_TLB_MCB_RD_SEM_CNTL, tmp | ENABLE_SEMAPHORE_MODE);
WREG32(MC_VM_L1_TLB_MCB_WR_SEM_CNTL, tmp | ENABLE_SEMAPHORE_MODE);
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_CNTL, ENABLE_CONTEXT | PAGE_TABLE_DEPTH(0) |
RANGE_PROTECTION_FAULT_ENABLE_DEFAULT);
AUX_SW_RX_HPD_DISCON | \
AUX_SW_RX_PARTIAL_BYTE | \
AUX_SW_NON_AUX_MODE | \
- AUX_SW_RX_MIN_COUNT_VIOL | \
- AUX_SW_RX_INVALID_STOP | \
AUX_SW_RX_SYNC_INVALID_L | \
AUX_SW_RX_SYNC_INVALID_H | \
AUX_SW_RX_INVALID_START | \
int ret;
u8 msg[1];
+ if (!radeon_mst)
+ return 0;
+
if (dig_connector->dpcd[DP_DPCD_REV] < 0x12)
return 0;
WREG32(MC_VM_MB_L1_TLB2_CNTL, tmp);
WREG32(MC_VM_MB_L1_TLB3_CNTL, tmp);
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_CNTL, ENABLE_CONTEXT | PAGE_TABLE_DEPTH(0) |
RANGE_PROTECTION_FAULT_ENABLE_DEFAULT);
L2_CACHE_BIGK_FRAGMENT_SIZE(4));
/* setup context0 */
WREG32(VM_CONTEXT0_PAGE_TABLE_START_ADDR, rdev->mc.gtt_start >> 12);
- WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, rdev->mc.gtt_end >> 12);
+ WREG32(VM_CONTEXT0_PAGE_TABLE_END_ADDR, (rdev->mc.gtt_end >> 12) - 1);
WREG32(VM_CONTEXT0_PAGE_TABLE_BASE_ADDR, rdev->gart.table_addr >> 12);
WREG32(VM_CONTEXT0_PROTECTION_FAULT_DEFAULT_ADDR,
(u32)(rdev->dummy_page.addr >> 12));
/* empty context1-15 */
/* set vm size, must be a multiple of 4 */
WREG32(VM_CONTEXT1_PAGE_TABLE_START_ADDR, 0);
- WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn);
+ WREG32(VM_CONTEXT1_PAGE_TABLE_END_ADDR, rdev->vm_manager.max_pfn - 1);
/* Assign the pt base to something valid for now; the pts used for
* the VMs are determined by the application and setup and assigned
* on the fly in the vm part of radeon_gart.c
#define USB_DEVICE_ID_ATEN_2PORTKVM 0x2204
#define USB_DEVICE_ID_ATEN_4PORTKVM 0x2205
#define USB_DEVICE_ID_ATEN_4PORTKVMC 0x2208
+#define USB_DEVICE_ID_ATEN_CS682 0x2213
#define USB_VENDOR_ID_ATMEL 0x03eb
#define USB_DEVICE_ID_ATMEL_MULTITOUCH 0x211c
/* bits 1..20 are reserved for classes */
#define HIDPP_QUIRK_DELAYED_INIT BIT(21)
#define HIDPP_QUIRK_WTP_PHYSICAL_BUTTONS BIT(22)
-#define HIDPP_QUIRK_MULTI_INPUT BIT(23)
/*
* There are two hidpp protocols in use, the first version hidpp10 is known
struct hid_field *field, struct hid_usage *usage,
unsigned long **bit, int *max)
{
- struct hidpp_device *hidpp = hid_get_drvdata(hdev);
-
- if ((hidpp->quirks & HIDPP_QUIRK_MULTI_INPUT) &&
- (field->application == HID_GD_KEYBOARD))
- return 0;
-
return -1;
}
{
struct wtp_data *wd = hidpp->private_data;
- if ((hidpp->quirks & HIDPP_QUIRK_MULTI_INPUT) && origin_is_hid_core)
- /* this is the generic hid-input call */
- return;
-
__set_bit(EV_ABS, input_dev->evbit);
__set_bit(EV_KEY, input_dev->evbit);
__clear_bit(EV_REL, input_dev->evbit);
if (hidpp->quirks & HIDPP_QUIRK_DELAYED_INIT)
connect_mask &= ~HID_CONNECT_HIDINPUT;
- /* Re-enable hidinput for multi-input devices */
- if (hidpp->quirks & HIDPP_QUIRK_MULTI_INPUT)
- connect_mask |= HID_CONNECT_HIDINPUT;
-
ret = hid_hw_start(hdev, connect_mask);
if (ret) {
hid_err(hdev, "%s:hid_hw_start returned error\n", __func__);
HID_BLUETOOTH_DEVICE(USB_VENDOR_ID_LOGITECH,
USB_DEVICE_ID_LOGITECH_T651),
.driver_data = HIDPP_QUIRK_CLASS_WTP },
- { /* Keyboard TK820 */
- HID_DEVICE(BUS_USB, HID_GROUP_LOGITECH_DJ_DEVICE,
- USB_VENDOR_ID_LOGITECH, 0x4102),
- .driver_data = HIDPP_QUIRK_DELAYED_INIT | HIDPP_QUIRK_MULTI_INPUT |
- HIDPP_QUIRK_CLASS_WTP },
{ HID_DEVICE(BUS_USB, HID_GROUP_LOGITECH_DJ_DEVICE,
USB_VENDOR_ID_LOGITECH, HID_ANY_ID)},
if (!report)
return -EINVAL;
- mutex_lock(&hsdev->mutex);
+ mutex_lock(hsdev->mutex_ptr);
if (flag == SENSOR_HUB_SYNC) {
memset(&hsdev->pending, 0, sizeof(hsdev->pending));
init_completion(&hsdev->pending.ready);
kfree(hsdev->pending.raw_data);
hsdev->pending.status = false;
}
- mutex_unlock(&hsdev->mutex);
+ mutex_unlock(hsdev->mutex_ptr);
return ret_val;
}
hsdev->vendor_id = hdev->vendor;
hsdev->product_id = hdev->product;
hsdev->usage = collection->usage;
- mutex_init(&hsdev->mutex);
+ hsdev->mutex_ptr = devm_kzalloc(&hdev->dev,
+ sizeof(struct mutex),
+ GFP_KERNEL);
+ if (!hsdev->mutex_ptr) {
+ ret = -ENOMEM;
+ goto err_stop_hw;
+ }
+ mutex_init(hsdev->mutex_ptr);
hsdev->start_collection_index = i;
if (last_hsdev)
last_hsdev->end_collection_index = i;
union acpi_object *obj;
struct acpi_device *adev;
acpi_handle handle;
+ int ret;
handle = ACPI_HANDLE(&client->dev);
if (!handle || acpi_bus_get_device(handle, &adev))
pdata->hid_descriptor_address = obj->integer.value;
ACPI_FREE(obj);
- return acpi_dev_add_driver_gpios(adev, i2c_hid_acpi_gpios);
+ /* GPIOs are optional */
+ ret = acpi_dev_add_driver_gpios(adev, i2c_hid_acpi_gpios);
+ return ret < 0 && ret != -ENXIO ? ret : 0;
}
static const struct acpi_device_id i2c_hid_acpi_match[] = {
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_2PORTKVM, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVM, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_4PORTKVMC, HID_QUIRK_NOGET },
+ { USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_CS682, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_CH, USB_DEVICE_ID_CH_FIGHTERSTICK, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_CH, USB_DEVICE_ID_CH_COMBATSTICK, HID_QUIRK_NOGET },
{ USB_VENDOR_ID_CH, USB_DEVICE_ID_CH_FLIGHT_SIM_ECLIPSE_YOKE, HID_QUIRK_NOGET },
int count = 0;
int i;
+ if (!touch_max)
+ return 0;
+
/* non-HID_GENERIC single touch input doesn't call this routine */
if ((touch_max == 1) && (wacom->features.type == HID_GENERIC))
return wacom->hid_data.tipswitch &&
help
This driver adds support for Toshiba TC86C001 GOKU-S chip.
-config BLK_DEV_CELLEB
- tristate "Toshiba's Cell Reference Set IDE support"
- depends on PPC_CELLEB
- select BLK_DEV_IDEDMA_PCI
- help
- This driver provides support for the on-board IDE controller on
- Toshiba Cell Reference Board.
- If unsure, say Y.
-
endif
# TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF
obj-$(CONFIG_BLK_DEV_ALI15X3) += alim15x3.o
obj-$(CONFIG_BLK_DEV_AMD74XX) += amd74xx.o
obj-$(CONFIG_BLK_DEV_ATIIXP) += atiixp.o
-obj-$(CONFIG_BLK_DEV_CELLEB) += scc_pata.o
obj-$(CONFIG_BLK_DEV_CMD64X) += cmd64x.o
obj-$(CONFIG_BLK_DEV_CS5520) += cs5520.o
obj-$(CONFIG_BLK_DEV_CS5530) += cs5530.o
+++ /dev/null
-/*
- * Support for IDE interfaces on Celleb platform
- *
- * (C) Copyright 2006 TOSHIBA CORPORATION
- *
- * This code is based on drivers/ide/pci/siimage.c:
- * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C) 2003 Red Hat
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#define PCI_DEVICE_ID_TOSHIBA_SCC_ATA 0x01b4
-
-#define SCC_PATA_NAME "scc IDE"
-
-#define TDVHSEL_MASTER 0x00000001
-#define TDVHSEL_SLAVE 0x00000004
-
-#define MODE_JCUSFEN 0x00000080
-
-#define CCKCTRL_ATARESET 0x00040000
-#define CCKCTRL_BUFCNT 0x00020000
-#define CCKCTRL_CRST 0x00010000
-#define CCKCTRL_OCLKEN 0x00000100
-#define CCKCTRL_ATACLKOEN 0x00000002
-#define CCKCTRL_LCLKEN 0x00000001
-
-#define QCHCD_IOS_SS 0x00000001
-
-#define QCHSD_STPDIAG 0x00020000
-
-#define INTMASK_MSK 0xD1000012
-#define INTSTS_SERROR 0x80000000
-#define INTSTS_PRERR 0x40000000
-#define INTSTS_RERR 0x10000000
-#define INTSTS_ICERR 0x01000000
-#define INTSTS_BMSINT 0x00000010
-#define INTSTS_BMHE 0x00000008
-#define INTSTS_IOIRQS 0x00000004
-#define INTSTS_INTRQ 0x00000002
-#define INTSTS_ACTEINT 0x00000001
-
-#define ECMODE_VALUE 0x01
-
-static struct scc_ports {
- unsigned long ctl, dma;
- struct ide_host *host; /* for removing port from system */
-} scc_ports[MAX_HWIFS];
-
-/* PIO transfer mode table */
-/* JCHST */
-static unsigned long JCHSTtbl[2][7] = {
- {0x0E, 0x05, 0x02, 0x03, 0x02, 0x00, 0x00}, /* 100MHz */
- {0x13, 0x07, 0x04, 0x04, 0x03, 0x00, 0x00} /* 133MHz */
-};
-
-/* JCHHT */
-static unsigned long JCHHTtbl[2][7] = {
- {0x0E, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00}, /* 100MHz */
- {0x13, 0x03, 0x03, 0x03, 0x03, 0x00, 0x00} /* 133MHz */
-};
-
-/* JCHCT */
-static unsigned long JCHCTtbl[2][7] = {
- {0x1D, 0x1D, 0x1C, 0x0B, 0x06, 0x00, 0x00}, /* 100MHz */
- {0x27, 0x26, 0x26, 0x0E, 0x09, 0x00, 0x00} /* 133MHz */
-};
-
-
-/* DMA transfer mode table */
-/* JCHDCTM/JCHDCTS */
-static unsigned long JCHDCTxtbl[2][7] = {
- {0x0A, 0x06, 0x04, 0x03, 0x01, 0x00, 0x00}, /* 100MHz */
- {0x0E, 0x09, 0x06, 0x04, 0x02, 0x01, 0x00} /* 133MHz */
-};
-
-/* JCSTWTM/JCSTWTS */
-static unsigned long JCSTWTxtbl[2][7] = {
- {0x06, 0x04, 0x03, 0x02, 0x02, 0x02, 0x00}, /* 100MHz */
- {0x09, 0x06, 0x04, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
-};
-
-/* JCTSS */
-static unsigned long JCTSStbl[2][7] = {
- {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x00}, /* 100MHz */
- {0x05, 0x05, 0x05, 0x05, 0x05, 0x05, 0x05} /* 133MHz */
-};
-
-/* JCENVT */
-static unsigned long JCENVTtbl[2][7] = {
- {0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x00}, /* 100MHz */
- {0x02, 0x02, 0x02, 0x02, 0x02, 0x02, 0x02} /* 133MHz */
-};
-
-/* JCACTSELS/JCACTSELM */
-static unsigned long JCACTSELtbl[2][7] = {
- {0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x00}, /* 100MHz */
- {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01} /* 133MHz */
-};
-
-
-static u8 scc_ide_inb(unsigned long port)
-{
- u32 data = in_be32((void*)port);
- return (u8)data;
-}
-
-static void scc_exec_command(ide_hwif_t *hwif, u8 cmd)
-{
- out_be32((void *)hwif->io_ports.command_addr, cmd);
- eieio();
- in_be32((void *)(hwif->dma_base + 0x01c));
- eieio();
-}
-
-static u8 scc_read_status(ide_hwif_t *hwif)
-{
- return (u8)in_be32((void *)hwif->io_ports.status_addr);
-}
-
-static u8 scc_read_altstatus(ide_hwif_t *hwif)
-{
- return (u8)in_be32((void *)hwif->io_ports.ctl_addr);
-}
-
-static u8 scc_dma_sff_read_status(ide_hwif_t *hwif)
-{
- return (u8)in_be32((void *)(hwif->dma_base + 4));
-}
-
-static void scc_write_devctl(ide_hwif_t *hwif, u8 ctl)
-{
- out_be32((void *)hwif->io_ports.ctl_addr, ctl);
- eieio();
- in_be32((void *)(hwif->dma_base + 0x01c));
- eieio();
-}
-
-static void scc_ide_insw(unsigned long port, void *addr, u32 count)
-{
- u16 *ptr = (u16 *)addr;
- while (count--) {
- *ptr++ = le16_to_cpu(in_be32((void*)port));
- }
-}
-
-static void scc_ide_insl(unsigned long port, void *addr, u32 count)
-{
- u16 *ptr = (u16 *)addr;
- while (count--) {
- *ptr++ = le16_to_cpu(in_be32((void*)port));
- *ptr++ = le16_to_cpu(in_be32((void*)port));
- }
-}
-
-static void scc_ide_outb(u8 addr, unsigned long port)
-{
- out_be32((void*)port, addr);
-}
-
-static void
-scc_ide_outsw(unsigned long port, void *addr, u32 count)
-{
- u16 *ptr = (u16 *)addr;
- while (count--) {
- out_be32((void*)port, cpu_to_le16(*ptr++));
- }
-}
-
-static void
-scc_ide_outsl(unsigned long port, void *addr, u32 count)
-{
- u16 *ptr = (u16 *)addr;
- while (count--) {
- out_be32((void*)port, cpu_to_le16(*ptr++));
- out_be32((void*)port, cpu_to_le16(*ptr++));
- }
-}
-
-/**
- * scc_set_pio_mode - set host controller for PIO mode
- * @hwif: port
- * @drive: drive
- *
- * Load the timing settings for this device mode into the
- * controller.
- */
-
-static void scc_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct scc_ports *ports = ide_get_hwifdata(hwif);
- unsigned long ctl_base = ports->ctl;
- unsigned long cckctrl_port = ctl_base + 0xff0;
- unsigned long piosht_port = ctl_base + 0x000;
- unsigned long pioct_port = ctl_base + 0x004;
- unsigned long reg;
- int offset;
- const u8 pio = drive->pio_mode - XFER_PIO_0;
-
- reg = in_be32((void __iomem *)cckctrl_port);
- if (reg & CCKCTRL_ATACLKOEN) {
- offset = 1; /* 133MHz */
- } else {
- offset = 0; /* 100MHz */
- }
- reg = JCHSTtbl[offset][pio] << 16 | JCHHTtbl[offset][pio];
- out_be32((void __iomem *)piosht_port, reg);
- reg = JCHCTtbl[offset][pio];
- out_be32((void __iomem *)pioct_port, reg);
-}
-
-/**
- * scc_set_dma_mode - set host controller for DMA mode
- * @hwif: port
- * @drive: drive
- *
- * Load the timing settings for this device mode into the
- * controller.
- */
-
-static void scc_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
-{
- struct scc_ports *ports = ide_get_hwifdata(hwif);
- unsigned long ctl_base = ports->ctl;
- unsigned long cckctrl_port = ctl_base + 0xff0;
- unsigned long mdmact_port = ctl_base + 0x008;
- unsigned long mcrcst_port = ctl_base + 0x00c;
- unsigned long sdmact_port = ctl_base + 0x010;
- unsigned long scrcst_port = ctl_base + 0x014;
- unsigned long udenvt_port = ctl_base + 0x018;
- unsigned long tdvhsel_port = ctl_base + 0x020;
- int is_slave = drive->dn & 1;
- int offset, idx;
- unsigned long reg;
- unsigned long jcactsel;
- const u8 speed = drive->dma_mode;
-
- reg = in_be32((void __iomem *)cckctrl_port);
- if (reg & CCKCTRL_ATACLKOEN) {
- offset = 1; /* 133MHz */
- } else {
- offset = 0; /* 100MHz */
- }
-
- idx = speed - XFER_UDMA_0;
-
- jcactsel = JCACTSELtbl[offset][idx];
- if (is_slave) {
- out_be32((void __iomem *)sdmact_port, JCHDCTxtbl[offset][idx]);
- out_be32((void __iomem *)scrcst_port, JCSTWTxtbl[offset][idx]);
- jcactsel = jcactsel << 2;
- out_be32((void __iomem *)tdvhsel_port, (in_be32((void __iomem *)tdvhsel_port) & ~TDVHSEL_SLAVE) | jcactsel);
- } else {
- out_be32((void __iomem *)mdmact_port, JCHDCTxtbl[offset][idx]);
- out_be32((void __iomem *)mcrcst_port, JCSTWTxtbl[offset][idx]);
- out_be32((void __iomem *)tdvhsel_port, (in_be32((void __iomem *)tdvhsel_port) & ~TDVHSEL_MASTER) | jcactsel);
- }
- reg = JCTSStbl[offset][idx] << 16 | JCENVTtbl[offset][idx];
- out_be32((void __iomem *)udenvt_port, reg);
-}
-
-static void scc_dma_host_set(ide_drive_t *drive, int on)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 unit = drive->dn & 1;
- u8 dma_stat = scc_dma_sff_read_status(hwif);
-
- if (on)
- dma_stat |= (1 << (5 + unit));
- else
- dma_stat &= ~(1 << (5 + unit));
-
- scc_ide_outb(dma_stat, hwif->dma_base + 4);
-}
-
-/**
- * scc_dma_setup - begin a DMA phase
- * @drive: target device
- * @cmd: command
- *
- * Build an IDE DMA PRD (IDE speak for scatter gather table)
- * and then set up the DMA transfer registers.
- *
- * Returns 0 on success. If a PIO fallback is required then 1
- * is returned.
- */
-
-static int scc_dma_setup(ide_drive_t *drive, struct ide_cmd *cmd)
-{
- ide_hwif_t *hwif = drive->hwif;
- u32 rw = (cmd->tf_flags & IDE_TFLAG_WRITE) ? 0 : ATA_DMA_WR;
- u8 dma_stat;
-
- /* fall back to pio! */
- if (ide_build_dmatable(drive, cmd) == 0)
- return 1;
-
- /* PRD table */
- out_be32((void __iomem *)(hwif->dma_base + 8), hwif->dmatable_dma);
-
- /* specify r/w */
- out_be32((void __iomem *)hwif->dma_base, rw);
-
- /* read DMA status for INTR & ERROR flags */
- dma_stat = scc_dma_sff_read_status(hwif);
-
- /* clear INTR & ERROR flags */
- out_be32((void __iomem *)(hwif->dma_base + 4), dma_stat | 6);
-
- return 0;
-}
-
-static void scc_dma_start(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 dma_cmd = scc_ide_inb(hwif->dma_base);
-
- /* start DMA */
- scc_ide_outb(dma_cmd | 1, hwif->dma_base);
-}
-
-static int __scc_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 dma_stat, dma_cmd;
-
- /* get DMA command mode */
- dma_cmd = scc_ide_inb(hwif->dma_base);
- /* stop DMA */
- scc_ide_outb(dma_cmd & ~1, hwif->dma_base);
- /* get DMA status */
- dma_stat = scc_dma_sff_read_status(hwif);
- /* clear the INTR & ERROR bits */
- scc_ide_outb(dma_stat | 6, hwif->dma_base + 4);
- /* verify good DMA status */
- return (dma_stat & 7) != 4 ? (0x10 | dma_stat) : 0;
-}
-
-/**
- * scc_dma_end - Stop DMA
- * @drive: IDE drive
- *
- * Check and clear INT Status register.
- * Then call __scc_dma_end().
- */
-
-static int scc_dma_end(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- void __iomem *dma_base = (void __iomem *)hwif->dma_base;
- unsigned long intsts_port = hwif->dma_base + 0x014;
- u32 reg;
- int dma_stat, data_loss = 0;
- static int retry = 0;
-
- /* errata A308 workaround: Step5 (check data loss) */
- /* We don't check non ide_disk because it is limited to UDMA4 */
- if (!(in_be32((void __iomem *)hwif->io_ports.ctl_addr)
- & ATA_ERR) &&
- drive->media == ide_disk && drive->current_speed > XFER_UDMA_4) {
- reg = in_be32((void __iomem *)intsts_port);
- if (!(reg & INTSTS_ACTEINT)) {
- printk(KERN_WARNING "%s: operation failed (transfer data loss)\n",
- drive->name);
- data_loss = 1;
- if (retry++) {
- struct request *rq = hwif->rq;
- ide_drive_t *drive;
- int i;
-
- /* ERROR_RESET and drive->crc_count are needed
- * to reduce DMA transfer mode in retry process.
- */
- if (rq)
- rq->errors |= ERROR_RESET;
-
- ide_port_for_each_dev(i, drive, hwif)
- drive->crc_count++;
- }
- }
- }
-
- while (1) {
- reg = in_be32((void __iomem *)intsts_port);
-
- if (reg & INTSTS_SERROR) {
- printk(KERN_WARNING "%s: SERROR\n", SCC_PATA_NAME);
- out_be32((void __iomem *)intsts_port, INTSTS_SERROR|INTSTS_BMSINT);
-
- out_be32(dma_base, in_be32(dma_base) & ~QCHCD_IOS_SS);
- continue;
- }
-
- if (reg & INTSTS_PRERR) {
- u32 maea0, maec0;
- unsigned long ctl_base = hwif->config_data;
-
- maea0 = in_be32((void __iomem *)(ctl_base + 0xF50));
- maec0 = in_be32((void __iomem *)(ctl_base + 0xF54));
-
- printk(KERN_WARNING "%s: PRERR [addr:%x cmd:%x]\n", SCC_PATA_NAME, maea0, maec0);
-
- out_be32((void __iomem *)intsts_port, INTSTS_PRERR|INTSTS_BMSINT);
-
- out_be32(dma_base, in_be32(dma_base) & ~QCHCD_IOS_SS);
- continue;
- }
-
- if (reg & INTSTS_RERR) {
- printk(KERN_WARNING "%s: Response Error\n", SCC_PATA_NAME);
- out_be32((void __iomem *)intsts_port, INTSTS_RERR|INTSTS_BMSINT);
-
- out_be32(dma_base, in_be32(dma_base) & ~QCHCD_IOS_SS);
- continue;
- }
-
- if (reg & INTSTS_ICERR) {
- out_be32(dma_base, in_be32(dma_base) & ~QCHCD_IOS_SS);
-
- printk(KERN_WARNING "%s: Illegal Configuration\n", SCC_PATA_NAME);
- out_be32((void __iomem *)intsts_port, INTSTS_ICERR|INTSTS_BMSINT);
- continue;
- }
-
- if (reg & INTSTS_BMSINT) {
- printk(KERN_WARNING "%s: Internal Bus Error\n", SCC_PATA_NAME);
- out_be32((void __iomem *)intsts_port, INTSTS_BMSINT);
-
- ide_do_reset(drive);
- continue;
- }
-
- if (reg & INTSTS_BMHE) {
- out_be32((void __iomem *)intsts_port, INTSTS_BMHE);
- continue;
- }
-
- if (reg & INTSTS_ACTEINT) {
- out_be32((void __iomem *)intsts_port, INTSTS_ACTEINT);
- continue;
- }
-
- if (reg & INTSTS_IOIRQS) {
- out_be32((void __iomem *)intsts_port, INTSTS_IOIRQS);
- continue;
- }
- break;
- }
-
- dma_stat = __scc_dma_end(drive);
- if (data_loss)
- dma_stat |= 2; /* emulate DMA error (to retry command) */
- return dma_stat;
-}
-
-/* returns 1 if dma irq issued, 0 otherwise */
-static int scc_dma_test_irq(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u32 int_stat = in_be32((void __iomem *)hwif->dma_base + 0x014);
-
- /* SCC errata A252,A308 workaround: Step4 */
- if ((in_be32((void __iomem *)hwif->io_ports.ctl_addr)
- & ATA_ERR) &&
- (int_stat & INTSTS_INTRQ))
- return 1;
-
- /* SCC errata A308 workaround: Step5 (polling IOIRQS) */
- if (int_stat & INTSTS_IOIRQS)
- return 1;
-
- return 0;
-}
-
-static u8 scc_udma_filter(ide_drive_t *drive)
-{
- ide_hwif_t *hwif = drive->hwif;
- u8 mask = hwif->ultra_mask;
-
- /* errata A308 workaround: limit non ide_disk drive to UDMA4 */
- if ((drive->media != ide_disk) && (mask & 0xE0)) {
- printk(KERN_INFO "%s: limit %s to UDMA4\n",
- SCC_PATA_NAME, drive->name);
- mask = ATA_UDMA4;
- }
-
- return mask;
-}
-
-/**
- * setup_mmio_scc - map CTRL/BMID region
- * @dev: PCI device we are configuring
- * @name: device name
- *
- */
-
-static int setup_mmio_scc (struct pci_dev *dev, const char *name)
-{
- void __iomem *ctl_addr;
- void __iomem *dma_addr;
- int i, ret;
-
- for (i = 0; i < MAX_HWIFS; i++) {
- if (scc_ports[i].ctl == 0)
- break;
- }
- if (i >= MAX_HWIFS)
- return -ENOMEM;
-
- ret = pci_request_selected_regions(dev, (1 << 2) - 1, name);
- if (ret < 0) {
- printk(KERN_ERR "%s: can't reserve resources\n", name);
- return ret;
- }
-
- ctl_addr = pci_ioremap_bar(dev, 0);
- if (!ctl_addr)
- goto fail_0;
-
- dma_addr = pci_ioremap_bar(dev, 1);
- if (!dma_addr)
- goto fail_1;
-
- pci_set_master(dev);
- scc_ports[i].ctl = (unsigned long)ctl_addr;
- scc_ports[i].dma = (unsigned long)dma_addr;
- pci_set_drvdata(dev, (void *) &scc_ports[i]);
-
- return 1;
-
- fail_1:
- iounmap(ctl_addr);
- fail_0:
- return -ENOMEM;
-}
-
-static int scc_ide_setup_pci_device(struct pci_dev *dev,
- const struct ide_port_info *d)
-{
- struct scc_ports *ports = pci_get_drvdata(dev);
- struct ide_host *host;
- struct ide_hw hw, *hws[] = { &hw };
- int i, rc;
-
- memset(&hw, 0, sizeof(hw));
- for (i = 0; i <= 8; i++)
- hw.io_ports_array[i] = ports->dma + 0x20 + i * 4;
- hw.irq = dev->irq;
- hw.dev = &dev->dev;
-
- rc = ide_host_add(d, hws, 1, &host);
- if (rc)
- return rc;
-
- ports->host = host;
-
- return 0;
-}
-
-/**
- * init_setup_scc - set up an SCC PATA Controller
- * @dev: PCI device
- * @d: IDE port info
- *
- * Perform the initial set up for this device.
- */
-
-static int init_setup_scc(struct pci_dev *dev, const struct ide_port_info *d)
-{
- unsigned long ctl_base;
- unsigned long dma_base;
- unsigned long cckctrl_port;
- unsigned long intmask_port;
- unsigned long mode_port;
- unsigned long ecmode_port;
- u32 reg = 0;
- struct scc_ports *ports;
- int rc;
-
- rc = pci_enable_device(dev);
- if (rc)
- goto end;
-
- rc = setup_mmio_scc(dev, d->name);
- if (rc < 0)
- goto end;
-
- ports = pci_get_drvdata(dev);
- ctl_base = ports->ctl;
- dma_base = ports->dma;
- cckctrl_port = ctl_base + 0xff0;
- intmask_port = dma_base + 0x010;
- mode_port = ctl_base + 0x024;
- ecmode_port = ctl_base + 0xf00;
-
- /* controller initialization */
- reg = 0;
- out_be32((void*)cckctrl_port, reg);
- reg |= CCKCTRL_ATACLKOEN;
- out_be32((void*)cckctrl_port, reg);
- reg |= CCKCTRL_LCLKEN | CCKCTRL_OCLKEN;
- out_be32((void*)cckctrl_port, reg);
- reg |= CCKCTRL_CRST;
- out_be32((void*)cckctrl_port, reg);
-
- for (;;) {
- reg = in_be32((void*)cckctrl_port);
- if (reg & CCKCTRL_CRST)
- break;
- udelay(5000);
- }
-
- reg |= CCKCTRL_ATARESET;
- out_be32((void*)cckctrl_port, reg);
-
- out_be32((void*)ecmode_port, ECMODE_VALUE);
- out_be32((void*)mode_port, MODE_JCUSFEN);
- out_be32((void*)intmask_port, INTMASK_MSK);
-
- rc = scc_ide_setup_pci_device(dev, d);
-
- end:
- return rc;
-}
-
-static void scc_tf_load(ide_drive_t *drive, struct ide_taskfile *tf, u8 valid)
-{
- struct ide_io_ports *io_ports = &drive->hwif->io_ports;
-
- if (valid & IDE_VALID_FEATURE)
- scc_ide_outb(tf->feature, io_ports->feature_addr);
- if (valid & IDE_VALID_NSECT)
- scc_ide_outb(tf->nsect, io_ports->nsect_addr);
- if (valid & IDE_VALID_LBAL)
- scc_ide_outb(tf->lbal, io_ports->lbal_addr);
- if (valid & IDE_VALID_LBAM)
- scc_ide_outb(tf->lbam, io_ports->lbam_addr);
- if (valid & IDE_VALID_LBAH)
- scc_ide_outb(tf->lbah, io_ports->lbah_addr);
- if (valid & IDE_VALID_DEVICE)
- scc_ide_outb(tf->device, io_ports->device_addr);
-}
-
-static void scc_tf_read(ide_drive_t *drive, struct ide_taskfile *tf, u8 valid)
-{
- struct ide_io_ports *io_ports = &drive->hwif->io_ports;
-
- if (valid & IDE_VALID_ERROR)
- tf->error = scc_ide_inb(io_ports->feature_addr);
- if (valid & IDE_VALID_NSECT)
- tf->nsect = scc_ide_inb(io_ports->nsect_addr);
- if (valid & IDE_VALID_LBAL)
- tf->lbal = scc_ide_inb(io_ports->lbal_addr);
- if (valid & IDE_VALID_LBAM)
- tf->lbam = scc_ide_inb(io_ports->lbam_addr);
- if (valid & IDE_VALID_LBAH)
- tf->lbah = scc_ide_inb(io_ports->lbah_addr);
- if (valid & IDE_VALID_DEVICE)
- tf->device = scc_ide_inb(io_ports->device_addr);
-}
-
-static void scc_input_data(ide_drive_t *drive, struct ide_cmd *cmd,
- void *buf, unsigned int len)
-{
- unsigned long data_addr = drive->hwif->io_ports.data_addr;
-
- len++;
-
- if (drive->io_32bit) {
- scc_ide_insl(data_addr, buf, len / 4);
-
- if ((len & 3) >= 2)
- scc_ide_insw(data_addr, (u8 *)buf + (len & ~3), 1);
- } else
- scc_ide_insw(data_addr, buf, len / 2);
-}
-
-static void scc_output_data(ide_drive_t *drive, struct ide_cmd *cmd,
- void *buf, unsigned int len)
-{
- unsigned long data_addr = drive->hwif->io_ports.data_addr;
-
- len++;
-
- if (drive->io_32bit) {
- scc_ide_outsl(data_addr, buf, len / 4);
-
- if ((len & 3) >= 2)
- scc_ide_outsw(data_addr, (u8 *)buf + (len & ~3), 1);
- } else
- scc_ide_outsw(data_addr, buf, len / 2);
-}
-
-/**
- * init_mmio_iops_scc - set up the iops for MMIO
- * @hwif: interface to set up
- *
- */
-
-static void init_mmio_iops_scc(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
- struct scc_ports *ports = pci_get_drvdata(dev);
- unsigned long dma_base = ports->dma;
-
- ide_set_hwifdata(hwif, ports);
-
- hwif->dma_base = dma_base;
- hwif->config_data = ports->ctl;
-}
-
-/**
- * init_iops_scc - set up iops
- * @hwif: interface to set up
- *
- * Do the basic setup for the SCC hardware interface
- * and then do the MMIO setup.
- */
-
-static void init_iops_scc(ide_hwif_t *hwif)
-{
- struct pci_dev *dev = to_pci_dev(hwif->dev);
-
- hwif->hwif_data = NULL;
- if (pci_get_drvdata(dev) == NULL)
- return;
- init_mmio_iops_scc(hwif);
-}
-
-static int scc_init_dma(ide_hwif_t *hwif, const struct ide_port_info *d)
-{
- return ide_allocate_dma_engine(hwif);
-}
-
-static u8 scc_cable_detect(ide_hwif_t *hwif)
-{
- return ATA_CBL_PATA80;
-}
-
-/**
- * init_hwif_scc - set up hwif
- * @hwif: interface to set up
- *
- * We do the basic set up of the interface structure. The SCC
- * requires several custom handlers so we override the default
- * ide DMA handlers appropriately.
- */
-
-static void init_hwif_scc(ide_hwif_t *hwif)
-{
- /* PTERADD */
- out_be32((void __iomem *)(hwif->dma_base + 0x018), hwif->dmatable_dma);
-
- if (in_be32((void __iomem *)(hwif->config_data + 0xff0)) & CCKCTRL_ATACLKOEN)
- hwif->ultra_mask = ATA_UDMA6; /* 133MHz */
- else
- hwif->ultra_mask = ATA_UDMA5; /* 100MHz */
-}
-
-static const struct ide_tp_ops scc_tp_ops = {
- .exec_command = scc_exec_command,
- .read_status = scc_read_status,
- .read_altstatus = scc_read_altstatus,
- .write_devctl = scc_write_devctl,
-
- .dev_select = ide_dev_select,
- .tf_load = scc_tf_load,
- .tf_read = scc_tf_read,
-
- .input_data = scc_input_data,
- .output_data = scc_output_data,
-};
-
-static const struct ide_port_ops scc_port_ops = {
- .set_pio_mode = scc_set_pio_mode,
- .set_dma_mode = scc_set_dma_mode,
- .udma_filter = scc_udma_filter,
- .cable_detect = scc_cable_detect,
-};
-
-static const struct ide_dma_ops scc_dma_ops = {
- .dma_host_set = scc_dma_host_set,
- .dma_setup = scc_dma_setup,
- .dma_start = scc_dma_start,
- .dma_end = scc_dma_end,
- .dma_test_irq = scc_dma_test_irq,
- .dma_lost_irq = ide_dma_lost_irq,
- .dma_timer_expiry = ide_dma_sff_timer_expiry,
- .dma_sff_read_status = scc_dma_sff_read_status,
-};
-
-static const struct ide_port_info scc_chipset = {
- .name = "sccIDE",
- .init_iops = init_iops_scc,
- .init_dma = scc_init_dma,
- .init_hwif = init_hwif_scc,
- .tp_ops = &scc_tp_ops,
- .port_ops = &scc_port_ops,
- .dma_ops = &scc_dma_ops,
- .host_flags = IDE_HFLAG_SINGLE,
- .irq_flags = IRQF_SHARED,
- .pio_mask = ATA_PIO4,
- .chipset = ide_pci,
-};
-
-/**
- * scc_init_one - pci layer discovery entry
- * @dev: PCI device
- * @id: ident table entry
- *
- * Called by the PCI code when it finds an SCC PATA controller.
- * We then use the IDE PCI generic helper to do most of the work.
- */
-
-static int scc_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- return init_setup_scc(dev, &scc_chipset);
-}
-
-/**
- * scc_remove - pci layer remove entry
- * @dev: PCI device
- *
- * Called by the PCI code when it removes an SCC PATA controller.
- */
-
-static void scc_remove(struct pci_dev *dev)
-{
- struct scc_ports *ports = pci_get_drvdata(dev);
- struct ide_host *host = ports->host;
-
- ide_host_remove(host);
-
- iounmap((void*)ports->dma);
- iounmap((void*)ports->ctl);
- pci_release_selected_regions(dev, (1 << 2) - 1);
- memset(ports, 0, sizeof(*ports));
-}
-
-static const struct pci_device_id scc_pci_tbl[] = {
- { PCI_VDEVICE(TOSHIBA_2, PCI_DEVICE_ID_TOSHIBA_SCC_ATA), 0 },
- { 0, },
-};
-MODULE_DEVICE_TABLE(pci, scc_pci_tbl);
-
-static struct pci_driver scc_pci_driver = {
- .name = "SCC IDE",
- .id_table = scc_pci_tbl,
- .probe = scc_init_one,
- .remove = scc_remove,
-};
-
-static int __init scc_ide_init(void)
-{
- return ide_pci_register_driver(&scc_pci_driver);
-}
-
-static void __exit scc_ide_exit(void)
-{
- pci_unregister_driver(&scc_pci_driver);
-}
-
-module_init(scc_ide_init);
-module_exit(scc_ide_exit);
-
-MODULE_DESCRIPTION("PCI driver module for Toshiba SCC IDE");
-MODULE_LICENSE("GPL");
{
int ret, i;
int len_words = len / sizeof(u16);
- __be16 be_buf[MMA9551_MAX_MAILBOX_DATA_REGS];
+ __be16 be_buf[MMA9551_MAX_MAILBOX_DATA_REGS / 2];
+
+ if (len_words > ARRAY_SIZE(be_buf)) {
+ dev_err(&client->dev, "Invalid buffer size %d\n", len);
+ return -EINVAL;
+ }
ret = mma9551_transfer(client, app_id, MMA9551_CMD_READ_CONFIG,
reg, NULL, 0, (u8 *) be_buf, len);
{
int ret, i;
int len_words = len / sizeof(u16);
- __be16 be_buf[MMA9551_MAX_MAILBOX_DATA_REGS];
+ __be16 be_buf[MMA9551_MAX_MAILBOX_DATA_REGS / 2];
+
+ if (len_words > ARRAY_SIZE(be_buf)) {
+ dev_err(&client->dev, "Invalid buffer size %d\n", len);
+ return -EINVAL;
+ }
ret = mma9551_transfer(client, app_id, MMA9551_CMD_READ_STATUS,
reg, NULL, 0, (u8 *) be_buf, len);
{
int i;
int len_words = len / sizeof(u16);
- __be16 be_buf[MMA9551_MAX_MAILBOX_DATA_REGS];
+ __be16 be_buf[(MMA9551_MAX_MAILBOX_DATA_REGS - 1) / 2];
+
+ if (len_words > ARRAY_SIZE(be_buf)) {
+ dev_err(&client->dev, "Invalid buffer size %d\n", len);
+ return -EINVAL;
+ }
for (i = 0; i < len_words; i++)
be_buf[i] = cpu_to_be16(buf[i]);
#define MMA9553_MASK_CONF_STEPCOALESCE GENMASK(7, 0)
#define MMA9553_REG_CONF_ACTTHD 0x0E
+#define MMA9553_MAX_ACTTHD GENMASK(15, 0)
/* Pedometer status registers (R-only) */
#define MMA9553_REG_STATUS 0x00
static int mma9553_read_activity_stepcnt(struct mma9553_data *data,
u8 *activity, u16 *stepcnt)
{
- u32 status_stepcnt;
- u16 status;
+ u16 buf[2];
int ret;
ret = mma9551_read_status_words(data->client, MMA9551_APPID_PEDOMETER,
- MMA9553_REG_STATUS, sizeof(u32),
- (u16 *) &status_stepcnt);
+ MMA9553_REG_STATUS, sizeof(u32), buf);
if (ret < 0) {
dev_err(&data->client->dev,
"error reading status and stepcnt\n");
return ret;
}
- status = status_stepcnt & MMA9553_MASK_CONF_WORD;
- *activity = mma9553_get_bits(status, MMA9553_MASK_STATUS_ACTIVITY);
- *stepcnt = status_stepcnt >> 16;
+ *activity = mma9553_get_bits(buf[0], MMA9553_MASK_STATUS_ACTIVITY);
+ *stepcnt = buf[1];
return 0;
}
case IIO_EV_INFO_PERIOD:
switch (chan->type) {
case IIO_ACTIVITY:
+ if (val < 0 || val > MMA9553_ACTIVITY_THD_TO_SEC(
+ MMA9553_MAX_ACTTHD))
+ return -EINVAL;
mutex_lock(&data->mutex);
ret = mma9553_set_config(data, MMA9553_REG_CONF_ACTTHD,
&data->conf.actthd,
.modified = 1, \
.channel2 = _chan2, \
.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), \
- .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBHEIGHT), \
+ .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBHEIGHT) | \
+ BIT(IIO_CHAN_INFO_ENABLE), \
.event_spec = mma9553_activity_events, \
.num_event_specs = ARRAY_SIZE(mma9553_activity_events), \
.ext_info = mma9553_ext_info, \
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &accel_info;
+ mutex_init(&adata->tb.buf_lock);
st_sensors_power_enable(indio_dev);
.channel = 0,
.address = AXP288_TS_ADC_H,
.datasheet_name = "TS_PIN",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.indexed = 1,
.type = IIO_TEMP,
.channel = 1,
.address = AXP288_PMIC_ADC_H,
.datasheet_name = "PMIC_TEMP",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.indexed = 1,
.type = IIO_TEMP,
.channel = 2,
.address = AXP288_GP_ADC_H,
.datasheet_name = "GPADC",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.indexed = 1,
.type = IIO_CURRENT,
.channel = 3,
.address = AXP20X_BATT_CHRG_I_H,
.datasheet_name = "BATT_CHG_I",
- .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.indexed = 1,
.type = IIO_CURRENT,
.channel = 4,
.address = AXP20X_BATT_DISCHRG_I_H,
.datasheet_name = "BATT_DISCHRG_I",
- .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
}, {
.indexed = 1,
.type = IIO_VOLTAGE,
.channel = 5,
.address = AXP20X_BATT_V_H,
.datasheet_name = "BATT_V",
- .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
},
};
chan->address))
dev_err(&indio_dev->dev, "TS pin restore\n");
break;
- case IIO_CHAN_INFO_PROCESSED:
- ret = axp288_adc_read_channel(val, chan->address, info->regmap);
- break;
default:
ret = -EINVAL;
}
#define CC10001_ADC_EOC_SET BIT(0)
#define CC10001_ADC_CHSEL_SAMPLED 0x0c
-#define CC10001_ADC_POWER_UP 0x10
-#define CC10001_ADC_POWER_UP_SET BIT(0)
+#define CC10001_ADC_POWER_DOWN 0x10
+#define CC10001_ADC_POWER_DOWN_SET BIT(0)
+
#define CC10001_ADC_DEBUG 0x14
#define CC10001_ADC_DATA_COUNT 0x20
u16 *buf;
struct mutex lock;
- unsigned long channel_map;
unsigned int start_delay_ns;
unsigned int eoc_delay_ns;
};
return readl(adc_dev->reg_base + reg);
}
+static void cc10001_adc_power_up(struct cc10001_adc_device *adc_dev)
+{
+ cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_DOWN, 0);
+ ndelay(adc_dev->start_delay_ns);
+}
+
+static void cc10001_adc_power_down(struct cc10001_adc_device *adc_dev)
+{
+ cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_DOWN,
+ CC10001_ADC_POWER_DOWN_SET);
+}
+
static void cc10001_adc_start(struct cc10001_adc_device *adc_dev,
unsigned int channel)
{
val = (channel & CC10001_ADC_CH_MASK) | CC10001_ADC_MODE_SINGLE_CONV;
cc10001_adc_write_reg(adc_dev, CC10001_ADC_CONFIG, val);
+ udelay(1);
val = cc10001_adc_read_reg(adc_dev, CC10001_ADC_CONFIG);
val = val | CC10001_ADC_START_CONV;
cc10001_adc_write_reg(adc_dev, CC10001_ADC_CONFIG, val);
struct iio_dev *indio_dev;
unsigned int delay_ns;
unsigned int channel;
+ unsigned int scan_idx;
bool sample_invalid;
u16 *data;
int i;
mutex_lock(&adc_dev->lock);
- cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_UP,
- CC10001_ADC_POWER_UP_SET);
-
- /* Wait for 8 (6+2) clock cycles before activating START */
- ndelay(adc_dev->start_delay_ns);
+ cc10001_adc_power_up(adc_dev);
/* Calculate delay step for eoc and sampled data */
delay_ns = adc_dev->eoc_delay_ns / CC10001_MAX_POLL_COUNT;
i = 0;
sample_invalid = false;
- for_each_set_bit(channel, indio_dev->active_scan_mask,
+ for_each_set_bit(scan_idx, indio_dev->active_scan_mask,
indio_dev->masklength) {
+ channel = indio_dev->channels[scan_idx].channel;
cc10001_adc_start(adc_dev, channel);
data[i] = cc10001_adc_poll_done(indio_dev, channel, delay_ns);
}
done:
- cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_UP, 0);
+ cc10001_adc_power_down(adc_dev);
mutex_unlock(&adc_dev->lock);
unsigned int delay_ns;
u16 val;
- cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_UP,
- CC10001_ADC_POWER_UP_SET);
-
- /* Wait for 8 (6+2) clock cycles before activating START */
- ndelay(adc_dev->start_delay_ns);
+ cc10001_adc_power_up(adc_dev);
/* Calculate delay step for eoc and sampled data */
delay_ns = adc_dev->eoc_delay_ns / CC10001_MAX_POLL_COUNT;
val = cc10001_adc_poll_done(indio_dev, chan->channel, delay_ns);
- cc10001_adc_write_reg(adc_dev, CC10001_ADC_POWER_UP, 0);
+ cc10001_adc_power_down(adc_dev);
return val;
}
case IIO_CHAN_INFO_SCALE:
ret = regulator_get_voltage(adc_dev->reg);
- if (ret)
+ if (ret < 0)
return ret;
*val = ret / 1000;
.update_scan_mode = &cc10001_update_scan_mode,
};
-static int cc10001_adc_channel_init(struct iio_dev *indio_dev)
+static int cc10001_adc_channel_init(struct iio_dev *indio_dev,
+ unsigned long channel_map)
{
- struct cc10001_adc_device *adc_dev = iio_priv(indio_dev);
struct iio_chan_spec *chan_array, *timestamp;
unsigned int bit, idx = 0;
- indio_dev->num_channels = bitmap_weight(&adc_dev->channel_map,
- CC10001_ADC_NUM_CHANNELS);
+ indio_dev->num_channels = bitmap_weight(&channel_map,
+ CC10001_ADC_NUM_CHANNELS) + 1;
- chan_array = devm_kcalloc(&indio_dev->dev, indio_dev->num_channels + 1,
+ chan_array = devm_kcalloc(&indio_dev->dev, indio_dev->num_channels,
sizeof(struct iio_chan_spec),
GFP_KERNEL);
if (!chan_array)
return -ENOMEM;
- for_each_set_bit(bit, &adc_dev->channel_map, CC10001_ADC_NUM_CHANNELS) {
+ for_each_set_bit(bit, &channel_map, CC10001_ADC_NUM_CHANNELS) {
struct iio_chan_spec *chan = &chan_array[idx];
chan->type = IIO_VOLTAGE;
unsigned long adc_clk_rate;
struct resource *res;
struct iio_dev *indio_dev;
+ unsigned long channel_map;
int ret;
indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*adc_dev));
adc_dev = iio_priv(indio_dev);
- adc_dev->channel_map = GENMASK(CC10001_ADC_NUM_CHANNELS - 1, 0);
+ channel_map = GENMASK(CC10001_ADC_NUM_CHANNELS - 1, 0);
if (!of_property_read_u32(node, "adc-reserved-channels", &ret))
- adc_dev->channel_map &= ~ret;
+ channel_map &= ~ret;
adc_dev->reg = devm_regulator_get(&pdev->dev, "vref");
if (IS_ERR(adc_dev->reg))
adc_dev->start_delay_ns = adc_dev->eoc_delay_ns * CC10001_WAIT_CYCLES;
/* Setup the ADC channels available on the device */
- ret = cc10001_adc_channel_init(indio_dev);
+ ret = cc10001_adc_channel_init(indio_dev, channel_map);
if (ret < 0)
goto err_disable_clk;
struct spi_message msg;
struct spi_transfer transfer[2];
- u8 tx_buf;
- u8 rx_buf[2];
-
struct regulator *reg;
struct mutex lock;
const struct mcp320x_chip_info *chip_info;
+
+ u8 tx_buf ____cacheline_aligned;
+ u8 rx_buf[2];
};
static int mcp320x_channel_to_tx_data(int device_index,
#include <linux/iio/iio.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
+#include <linux/math64.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
const struct vadc_channel_prop *prop, u16 adc_code)
{
const struct vadc_prescale_ratio *prescale;
- s32 voltage;
+ s64 voltage;
voltage = adc_code - vadc->graph[prop->calibration].gnd;
voltage *= vadc->graph[prop->calibration].dx;
- voltage = voltage / vadc->graph[prop->calibration].dy;
+ voltage = div64_s64(voltage, vadc->graph[prop->calibration].dy);
if (prop->calibration == VADC_CALIB_ABSOLUTE)
voltage += vadc->graph[prop->calibration].dx;
voltage = voltage * prescale->den;
- return voltage / prescale->num;
+ return div64_s64(voltage, prescale->num);
}
static int vadc_decimation_from_dt(u32 value)
switch (chan->address) {
case XADC_REG_VCCINT:
case XADC_REG_VCCAUX:
+ case XADC_REG_VREFP:
case XADC_REG_VCCBRAM:
case XADC_REG_VCCPINT:
case XADC_REG_VCCPAUX:
.num_event_specs = (_alarm) ? ARRAY_SIZE(xadc_voltage_events) : 0, \
.scan_index = (_scan_index), \
.scan_type = { \
- .sign = 'u', \
+ .sign = ((_addr) == XADC_REG_VREFN) ? 's' : 'u', \
.realbits = 12, \
.storagebits = 16, \
.shift = 4, \
static const struct iio_chan_spec xadc_channels[] = {
XADC_CHAN_TEMP(0, 8, XADC_REG_TEMP),
XADC_CHAN_VOLTAGE(0, 9, XADC_REG_VCCINT, "vccint", true),
- XADC_CHAN_VOLTAGE(1, 10, XADC_REG_VCCINT, "vccaux", true),
+ XADC_CHAN_VOLTAGE(1, 10, XADC_REG_VCCAUX, "vccaux", true),
XADC_CHAN_VOLTAGE(2, 14, XADC_REG_VCCBRAM, "vccbram", true),
XADC_CHAN_VOLTAGE(3, 5, XADC_REG_VCCPINT, "vccpint", true),
XADC_CHAN_VOLTAGE(4, 6, XADC_REG_VCCPAUX, "vccpaux", true),
#define XADC_REG_MAX_VCCPINT 0x28
#define XADC_REG_MAX_VCCPAUX 0x29
#define XADC_REG_MAX_VCCO_DDR 0x2a
-#define XADC_REG_MIN_VCCPINT 0x2b
-#define XADC_REG_MIN_VCCPAUX 0x2c
-#define XADC_REG_MIN_VCCO_DDR 0x2d
+#define XADC_REG_MIN_VCCPINT 0x2c
+#define XADC_REG_MIN_VCCPAUX 0x2d
+#define XADC_REG_MIN_VCCO_DDR 0x2e
#define XADC_REG_CONF0 0x40
#define XADC_REG_CONF1 0x41
struct st_sensors_platform_data *of_pdata;
int err = 0;
- mutex_init(&sdata->tb.buf_lock);
-
/* If OF/DT pdata exists, it will take precedence of anything else */
of_pdata = st_sensors_of_probe(indio_dev->dev.parent, pdata);
if (of_pdata)
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &gyro_info;
+ mutex_init(&gdata->tb.buf_lock);
st_sensors_power_enable(indio_dev);
kfifo_free(&buf->kf);
ret = __iio_allocate_kfifo(buf, buf->buffer.bytes_per_datum,
buf->buffer.length);
- buf->update_needed = false;
+ if (ret >= 0)
+ buf->update_needed = false;
} else {
kfifo_reset_out(&buf->kf);
}
static const struct iio_chan_spec prox_channels[] = {
{
.type = IIO_PROXIMITY,
- .modified = 1,
- .channel2 = IIO_NO_MOD,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) |
BIT(IIO_CHAN_INFO_SCALE) |
struct iio_dev *indio_dev;
struct prox_state *prox_state;
struct hid_sensor_hub_device *hsdev = pdev->dev.platform_data;
- struct iio_chan_spec *channels;
indio_dev = devm_iio_device_alloc(&pdev->dev,
sizeof(struct prox_state));
return ret;
}
- channels = kmemdup(prox_channels, sizeof(prox_channels), GFP_KERNEL);
- if (!channels) {
+ indio_dev->channels = kmemdup(prox_channels, sizeof(prox_channels),
+ GFP_KERNEL);
+ if (!indio_dev->channels) {
dev_err(&pdev->dev, "failed to duplicate channels\n");
return -ENOMEM;
}
- ret = prox_parse_report(pdev, hsdev, channels,
+ ret = prox_parse_report(pdev, hsdev,
+ (struct iio_chan_spec *)indio_dev->channels,
HID_USAGE_SENSOR_PROX, prox_state);
if (ret) {
dev_err(&pdev->dev, "failed to setup attributes\n");
goto error_free_dev_mem;
}
- indio_dev->channels = channels;
indio_dev->num_channels =
ARRAY_SIZE(prox_channels);
indio_dev->dev.parent = &pdev->dev;
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &magn_info;
+ mutex_init(&mdata->tb.buf_lock);
st_sensors_power_enable(indio_dev);
var2 = (((((adc_temp >> 4) - ((s32)le16_to_cpu(buf[T1]))) *
((adc_temp >> 4) - ((s32)le16_to_cpu(buf[T1])))) >> 12) *
((s32)(s16)le16_to_cpu(buf[T3]))) >> 14;
+ data->t_fine = var1 + var2;
return (data->t_fine * 5 + 128) >> 8;
}
static const struct iio_chan_spec press_channels[] = {
{
.type = IIO_PRESSURE,
- .modified = 1,
- .channel2 = IIO_NO_MOD,
.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_OFFSET) |
BIT(IIO_CHAN_INFO_SCALE) |
indio_dev->modes = INDIO_DIRECT_MODE;
indio_dev->info = &press_info;
+ mutex_init(&press_data->tb.buf_lock);
st_sensors_power_enable(indio_dev);
cm_reject_sidr_req(cm_id_priv, IB_SIDR_REJECT);
break;
case IB_CM_REQ_SENT:
+ case IB_CM_MRA_REQ_RCVD:
ib_cancel_mad(cm_id_priv->av.port->mad_agent, cm_id_priv->msg);
spin_unlock_irq(&cm_id_priv->lock);
ib_send_cm_rej(cm_id, IB_CM_REJ_TIMEOUT,
NULL, 0, NULL, 0);
}
break;
- case IB_CM_MRA_REQ_RCVD:
case IB_CM_REP_SENT:
case IB_CM_MRA_REP_RCVD:
ib_cancel_mad(cm_id_priv->av.port->mad_agent, cm_id_priv->msg);
listen_ib = (struct sockaddr_ib *) &listen_id->route.addr.src_addr;
ib = (struct sockaddr_ib *) &id->route.addr.src_addr;
ib->sib_family = listen_ib->sib_family;
- ib->sib_pkey = path->pkey;
- ib->sib_flowinfo = path->flow_label;
- memcpy(&ib->sib_addr, &path->sgid, 16);
+ if (path) {
+ ib->sib_pkey = path->pkey;
+ ib->sib_flowinfo = path->flow_label;
+ memcpy(&ib->sib_addr, &path->sgid, 16);
+ } else {
+ ib->sib_pkey = listen_ib->sib_pkey;
+ ib->sib_flowinfo = listen_ib->sib_flowinfo;
+ ib->sib_addr = listen_ib->sib_addr;
+ }
ib->sib_sid = listen_ib->sib_sid;
ib->sib_sid_mask = cpu_to_be64(0xffffffffffffffffULL);
ib->sib_scope_id = listen_ib->sib_scope_id;
- ib = (struct sockaddr_ib *) &id->route.addr.dst_addr;
- ib->sib_family = listen_ib->sib_family;
- ib->sib_pkey = path->pkey;
- ib->sib_flowinfo = path->flow_label;
- memcpy(&ib->sib_addr, &path->dgid, 16);
+ if (path) {
+ ib = (struct sockaddr_ib *) &id->route.addr.dst_addr;
+ ib->sib_family = listen_ib->sib_family;
+ ib->sib_pkey = path->pkey;
+ ib->sib_flowinfo = path->flow_label;
+ memcpy(&ib->sib_addr, &path->dgid, 16);
+ }
}
static __be16 ss_get_port(const struct sockaddr_storage *ss)
{
struct cma_hdr *hdr;
- if ((listen_id->route.addr.src_addr.ss_family == AF_IB) &&
- (ib_event->event == IB_CM_REQ_RECEIVED)) {
- cma_save_ib_info(id, listen_id, ib_event->param.req_rcvd.primary_path);
+ if (listen_id->route.addr.src_addr.ss_family == AF_IB) {
+ if (ib_event->event == IB_CM_REQ_RECEIVED)
+ cma_save_ib_info(id, listen_id, ib_event->param.req_rcvd.primary_path);
+ else if (ib_event->event == IB_CM_SIDR_REQ_RECEIVED)
+ cma_save_ib_info(id, listen_id, NULL);
return 0;
}
#include "iwpm_util.h"
-static const char iwpm_ulib_name[] = "iWarpPortMapperUser";
+static const char iwpm_ulib_name[IWPM_ULIBNAME_SIZE] = "iWarpPortMapperUser";
static int iwpm_ulib_version = 3;
static int iwpm_user_pid = IWPM_PID_UNDEFINED;
static atomic_t echo_nlmsg_seq;
sizeof(ep->com.mapped_remote_addr));
}
-static int get_remote_addr(struct c4iw_ep *ep)
+static int get_remote_addr(struct c4iw_ep *parent_ep, struct c4iw_ep *child_ep)
{
int ret;
- print_addr(&ep->com, __func__, "get_remote_addr");
+ print_addr(&parent_ep->com, __func__, "get_remote_addr parent_ep ");
+ print_addr(&child_ep->com, __func__, "get_remote_addr child_ep ");
- ret = iwpm_get_remote_info(&ep->com.mapped_local_addr,
- &ep->com.mapped_remote_addr,
- &ep->com.remote_addr, RDMA_NL_C4IW);
+ ret = iwpm_get_remote_info(&parent_ep->com.mapped_local_addr,
+ &child_ep->com.mapped_remote_addr,
+ &child_ep->com.remote_addr, RDMA_NL_C4IW);
if (ret)
- pr_info(MOD "Unable to find remote peer addr info - err %d\n",
- ret);
+ PDBG("Unable to find remote peer addr info - err %d\n", ret);
return ret;
}
}
memcpy(&child_ep->com.remote_addr, &child_ep->com.mapped_remote_addr,
sizeof(child_ep->com.remote_addr));
- get_remote_addr(child_ep);
+ get_remote_addr(parent_ep, child_ep);
c4iw_get_ep(&parent_ep->com);
child_ep->parent_ep = parent_ep;
t4_sq_host_wq_pidx(&qp->wq),
t4_sq_wq_size(&qp->wq));
if (ret) {
- pr_err(KERN_ERR MOD "%s: Fatal error - "
+ pr_err(MOD "%s: Fatal error - "
"DB overflow recovery failed - "
"error syncing SQ qid %u\n",
pci_name(ctx->lldi.pdev), qp->wq.sq.qid);
t4_rq_wq_size(&qp->wq));
if (ret) {
- pr_err(KERN_ERR MOD "%s: Fatal error - "
+ pr_err(MOD "%s: Fatal error - "
"DB overflow recovery failed - "
"error syncing RQ qid %u\n",
pci_name(ctx->lldi.pdev), qp->wq.rq.qid);
return -EINVAL;
}
- memcpy(&my_gid.raw, gid->raw, sizeof(union ib_gid));
+ memcpy(&my_gid, gid->raw, sizeof(union ib_gid));
subnet_prefix = be64_to_cpu(my_gid.global.subnet_prefix);
interface_id = be64_to_cpu(my_gid.global.interface_id);
return -EINVAL;
}
- memcpy(&my_gid.raw, gid->raw, sizeof(union ib_gid));
+ memcpy(&my_gid, gid->raw, sizeof(union ib_gid));
subnet_prefix = be64_to_cpu(my_gid.global.subnet_prefix);
interface_id = be64_to_cpu(my_gid.global.interface_id);
MLX4_CMD_TIME_CLASS_B,
MLX4_CMD_WRAPPED);
if (err)
- pr_warn(KERN_WARNING
- "set port %d command failed\n", gw->port);
+ pr_warn("set port %d command failed\n", gw->port);
}
mlx4_free_cmd_mailbox(dev, mailbox);
if (ah->ah_flags & IB_AH_GRH) {
if (ah->grh.sgid_index >= gen->port[port - 1].gid_table_len) {
- pr_err(KERN_ERR "sgid_index (%u) too large. max is %d\n",
+ pr_err("sgid_index (%u) too large. max is %d\n",
ah->grh.sgid_index, gen->port[port - 1].gid_table_len);
return -EINVAL;
}
#include <be_roce.h>
#include "ocrdma_sli.h"
-#define OCRDMA_ROCE_DRV_VERSION "10.4.205.0u"
+#define OCRDMA_ROCE_DRV_VERSION "10.6.0.0"
#define OCRDMA_ROCE_DRV_DESC "Emulex OneConnect RoCE Driver"
#define OCRDMA_NODE_DESC "Emulex OneConnect RoCE HCA"
memcpy(&in6, ah_attr->grh.dgid.raw, sizeof(in6));
if (rdma_is_multicast_addr(&in6))
rdma_get_mcast_mac(&in6, mac_addr);
+ else if (rdma_link_local_addr(&in6))
+ rdma_get_ll_mac(&in6, mac_addr);
else
memcpy(mac_addr, ah_attr->dmac, ETH_ALEN);
return 0;
vlan_tag = attr->vlan_id;
if (!vlan_tag || (vlan_tag > 0xFFF))
vlan_tag = dev->pvid;
- if (vlan_tag && (vlan_tag < 0x1000)) {
+ if (vlan_tag || dev->pfc_state) {
+ if (!vlan_tag) {
+ pr_err("ocrdma%d:Using VLAN with PFC is recommended\n",
+ dev->id);
+ pr_err("ocrdma%d:Using VLAN 0 for this connection\n",
+ dev->id);
+ }
eth.eth_type = cpu_to_be16(0x8100);
eth.roce_eth_type = cpu_to_be16(OCRDMA_ROCE_ETH_TYPE);
vlan_tag |= (dev->sl & 0x07) << OCRDMA_VID_PCP_SHIFT;
goto av_conf_err;
}
- if (pd->uctx) {
+ if ((pd->uctx) &&
+ (!rdma_is_multicast_addr((struct in6_addr *)attr->grh.dgid.raw)) &&
+ (!rdma_link_local_addr((struct in6_addr *)attr->grh.dgid.raw))) {
status = rdma_addr_find_dmac_by_grh(&sgid, &attr->grh.dgid,
attr->dmac, &attr->vlan_id);
if (status) {
struct ocrdma_eqe eqe;
struct ocrdma_eqe *ptr;
u16 cq_id;
+ u8 mcode;
int budget = eq->cq_cnt;
do {
ptr = ocrdma_get_eqe(eq);
eqe = *ptr;
ocrdma_le32_to_cpu(&eqe, sizeof(eqe));
+ mcode = (eqe.id_valid & OCRDMA_EQE_MAJOR_CODE_MASK)
+ >> OCRDMA_EQE_MAJOR_CODE_SHIFT;
+ if (mcode == OCRDMA_MAJOR_CODE_SENTINAL)
+ pr_err("EQ full on eqid = 0x%x, eqe = 0x%x\n",
+ eq->q.id, eqe.id_valid);
if ((eqe.id_valid & OCRDMA_EQE_VALID_MASK) == 0)
break;
struct ocrdma_alloc_pd_range_rsp *rsp;
/* Pre allocate the DPP PDs */
- cmd = ocrdma_init_emb_mqe(OCRDMA_CMD_ALLOC_PD_RANGE, sizeof(*cmd));
- if (!cmd)
- return -ENOMEM;
- cmd->pd_count = dev->attr.max_dpp_pds;
- cmd->enable_dpp_rsvd |= OCRDMA_ALLOC_PD_ENABLE_DPP;
- status = ocrdma_mbx_cmd(dev, (struct ocrdma_mqe *)cmd);
- if (status)
- goto mbx_err;
- rsp = (struct ocrdma_alloc_pd_range_rsp *)cmd;
-
- if ((rsp->dpp_page_pdid & OCRDMA_ALLOC_PD_RSP_DPP) && rsp->pd_count) {
- dev->pd_mgr->dpp_page_index = rsp->dpp_page_pdid >>
- OCRDMA_ALLOC_PD_RSP_DPP_PAGE_SHIFT;
- dev->pd_mgr->pd_dpp_start = rsp->dpp_page_pdid &
- OCRDMA_ALLOC_PD_RNG_RSP_START_PDID_MASK;
- dev->pd_mgr->max_dpp_pd = rsp->pd_count;
- pd_bitmap_size = BITS_TO_LONGS(rsp->pd_count) * sizeof(long);
- dev->pd_mgr->pd_dpp_bitmap = kzalloc(pd_bitmap_size,
- GFP_KERNEL);
+ if (dev->attr.max_dpp_pds) {
+ cmd = ocrdma_init_emb_mqe(OCRDMA_CMD_ALLOC_PD_RANGE,
+ sizeof(*cmd));
+ if (!cmd)
+ return -ENOMEM;
+ cmd->pd_count = dev->attr.max_dpp_pds;
+ cmd->enable_dpp_rsvd |= OCRDMA_ALLOC_PD_ENABLE_DPP;
+ status = ocrdma_mbx_cmd(dev, (struct ocrdma_mqe *)cmd);
+ rsp = (struct ocrdma_alloc_pd_range_rsp *)cmd;
+
+ if (!status && (rsp->dpp_page_pdid & OCRDMA_ALLOC_PD_RSP_DPP) &&
+ rsp->pd_count) {
+ dev->pd_mgr->dpp_page_index = rsp->dpp_page_pdid >>
+ OCRDMA_ALLOC_PD_RSP_DPP_PAGE_SHIFT;
+ dev->pd_mgr->pd_dpp_start = rsp->dpp_page_pdid &
+ OCRDMA_ALLOC_PD_RNG_RSP_START_PDID_MASK;
+ dev->pd_mgr->max_dpp_pd = rsp->pd_count;
+ pd_bitmap_size =
+ BITS_TO_LONGS(rsp->pd_count) * sizeof(long);
+ dev->pd_mgr->pd_dpp_bitmap = kzalloc(pd_bitmap_size,
+ GFP_KERNEL);
+ }
+ kfree(cmd);
}
- kfree(cmd);
cmd = ocrdma_init_emb_mqe(OCRDMA_CMD_ALLOC_PD_RANGE, sizeof(*cmd));
if (!cmd)
cmd->pd_count = dev->attr.max_pd - dev->attr.max_dpp_pds;
status = ocrdma_mbx_cmd(dev, (struct ocrdma_mqe *)cmd);
- if (status)
- goto mbx_err;
rsp = (struct ocrdma_alloc_pd_range_rsp *)cmd;
- if (rsp->pd_count) {
+ if (!status && rsp->pd_count) {
dev->pd_mgr->pd_norm_start = rsp->dpp_page_pdid &
OCRDMA_ALLOC_PD_RNG_RSP_START_PDID_MASK;
dev->pd_mgr->max_normal_pd = rsp->pd_count;
dev->pd_mgr->pd_norm_bitmap = kzalloc(pd_bitmap_size,
GFP_KERNEL);
}
+ kfree(cmd);
if (dev->pd_mgr->pd_norm_bitmap || dev->pd_mgr->pd_dpp_bitmap) {
/* Enable PD resource manager */
dev->pd_mgr->pd_prealloc_valid = true;
- } else {
- return -ENOMEM;
+ return 0;
}
-mbx_err:
- kfree(cmd);
return status;
}
struct ocrdma_query_qp *cmd;
struct ocrdma_query_qp_rsp *rsp;
- cmd = ocrdma_init_emb_mqe(OCRDMA_CMD_QUERY_QP, sizeof(*cmd));
+ cmd = ocrdma_init_emb_mqe(OCRDMA_CMD_QUERY_QP, sizeof(*rsp));
if (!cmd)
return status;
cmd->qp_id = qp->id;
int status;
struct ib_ah_attr *ah_attr = &attrs->ah_attr;
union ib_gid sgid, zgid;
- u32 vlan_id;
+ u32 vlan_id = 0xFFFF;
u8 mac_addr[6];
struct ocrdma_dev *dev = get_ocrdma_dev(qp->ibqp.device);
cmd->params.vlan_dmac_b4_to_b5 = mac_addr[4] | (mac_addr[5] << 8);
if (attr_mask & IB_QP_VID) {
vlan_id = attrs->vlan_id;
+ } else if (dev->pfc_state) {
+ vlan_id = 0;
+ pr_err("ocrdma%d:Using VLAN with PFC is recommended\n",
+ dev->id);
+ pr_err("ocrdma%d:Using VLAN 0 for this connection\n",
+ dev->id);
+ }
+
+ if (vlan_id < 0x1000) {
cmd->params.vlan_dmac_b4_to_b5 |=
vlan_id << OCRDMA_QP_PARAMS_VLAN_SHIFT;
cmd->flags |= OCRDMA_QP_PARA_VLAN_EN_VALID;
cmd->params.rnt_rc_sl_fl |=
(dev->sl & 0x07) << OCRDMA_QP_PARAMS_SL_SHIFT;
}
+
return 0;
}
cmd->flags |= OCRDMA_QP_PARA_DST_QPN_VALID;
}
if (attr_mask & IB_QP_PATH_MTU) {
- if (attrs->path_mtu < IB_MTU_256 ||
+ if (attrs->path_mtu < IB_MTU_512 ||
attrs->path_mtu > IB_MTU_4096) {
+ pr_err("ocrdma%d: IB MTU %d is not supported\n",
+ dev->id, ib_mtu_enum_to_int(attrs->path_mtu));
status = -EINVAL;
goto pmtu_err;
}
ocrdma_free_pd_pool(dev);
ocrdma_mbx_delete_ah_tbl(dev);
- /* cleanup the eqs */
- ocrdma_destroy_eqs(dev);
-
/* cleanup the control path */
ocrdma_destroy_mq(dev);
+
+ /* cleanup the eqs */
+ ocrdma_destroy_eqs(dev);
}
struct ocrdma_mqe_hdr hdr;
struct ocrdma_mbx_rsp rsp;
struct ocrdma_qp_params params;
+ u32 dpp_credits_cqid;
+ u32 rbq_id;
};
enum {
enum {
OCRDMA_EQE_VALID_SHIFT = 0,
OCRDMA_EQE_VALID_MASK = BIT(0),
+ OCRDMA_EQE_MAJOR_CODE_MASK = 0x0E,
+ OCRDMA_EQE_MAJOR_CODE_SHIFT = 0x01,
OCRDMA_EQE_FOR_CQE_MASK = 0xFFFE,
OCRDMA_EQE_RESOURCE_ID_SHIFT = 16,
OCRDMA_EQE_RESOURCE_ID_MASK = 0xFFFF <<
OCRDMA_EQE_RESOURCE_ID_SHIFT,
};
+enum major_code {
+ OCRDMA_MAJOR_CODE_COMPLETION = 0x00,
+ OCRDMA_MAJOR_CODE_SENTINAL = 0x01
+};
+
struct ocrdma_eqe {
u32 id_valid;
};
if (!pd)
return ERR_PTR(-ENOMEM);
- if (udata && uctx) {
+ if (udata && uctx && dev->attr.max_dpp_pds) {
pd->dpp_enabled =
ocrdma_get_asic_type(dev) == OCRDMA_ASIC_GEN_SKH_R;
pd->num_dpp_qp =
struct ocrdma_qp *qp;
struct ocrdma_dev *dev;
struct ib_qp_attr attrs;
- int attr_mask = IB_QP_STATE;
+ int attr_mask;
unsigned long flags;
qp = get_ocrdma_qp(ibqp);
dev = get_ocrdma_dev(ibqp->device);
- attrs.qp_state = IB_QPS_ERR;
pd = qp->pd;
/* change the QP state to ERROR */
- _ocrdma_modify_qp(ibqp, &attrs, attr_mask);
-
+ if (qp->state != OCRDMA_QPS_RST) {
+ attrs.qp_state = IB_QPS_ERR;
+ attr_mask = IB_QP_STATE;
+ _ocrdma_modify_qp(ibqp, &attrs, attr_mask);
+ }
/* ensure that CQEs for newly created QP (whose id may be same with
* one which just getting destroyed are same), dont get
* discarded until the old CQEs are discarded.
/* PCI Device ID (here for NodeInfo) */
u16 deviceid;
/* for write combining settings */
- unsigned long wc_cookie;
+ int wc_cookie;
unsigned long wc_base;
unsigned long wc_len;
if (!ret) {
dd->wc_cookie = arch_phys_wc_add(pioaddr, piolen);
if (dd->wc_cookie < 0)
- ret = -EINVAL;
+ /* use error from routine */
+ ret = dd->wc_cookie;
}
return ret;
input_close_device(handle);
}
+static bool joydev_dev_is_absolute_mouse(struct input_dev *dev)
+{
+ DECLARE_BITMAP(jd_scratch, KEY_CNT);
+
+ BUILD_BUG_ON(ABS_CNT > KEY_CNT || EV_CNT > KEY_CNT);
+
+ /*
+ * Virtualization (VMware, etc) and remote management (HP
+ * ILO2) solutions use absolute coordinates for their virtual
+ * pointing devices so that there is one-to-one relationship
+ * between pointer position on the host screen and virtual
+ * guest screen, and so their mice use ABS_X, ABS_Y and 3
+ * primary button events. This clashes with what joydev
+ * considers to be joysticks (a device with at minimum ABS_X
+ * axis).
+ *
+ * Here we are trying to separate absolute mice from
+ * joysticks. A device is, for joystick detection purposes,
+ * considered to be an absolute mouse if the following is
+ * true:
+ *
+ * 1) Event types are exactly EV_ABS, EV_KEY and EV_SYN.
+ * 2) Absolute events are exactly ABS_X and ABS_Y.
+ * 3) Keys are exactly BTN_LEFT, BTN_RIGHT and BTN_MIDDLE.
+ * 4) Device is not on "Amiga" bus.
+ */
+
+ bitmap_zero(jd_scratch, EV_CNT);
+ __set_bit(EV_ABS, jd_scratch);
+ __set_bit(EV_KEY, jd_scratch);
+ __set_bit(EV_SYN, jd_scratch);
+ if (!bitmap_equal(jd_scratch, dev->evbit, EV_CNT))
+ return false;
+
+ bitmap_zero(jd_scratch, ABS_CNT);
+ __set_bit(ABS_X, jd_scratch);
+ __set_bit(ABS_Y, jd_scratch);
+ if (!bitmap_equal(dev->absbit, jd_scratch, ABS_CNT))
+ return false;
+
+ bitmap_zero(jd_scratch, KEY_CNT);
+ __set_bit(BTN_LEFT, jd_scratch);
+ __set_bit(BTN_RIGHT, jd_scratch);
+ __set_bit(BTN_MIDDLE, jd_scratch);
+
+ if (!bitmap_equal(dev->keybit, jd_scratch, KEY_CNT))
+ return false;
+
+ /*
+ * Amiga joystick (amijoy) historically uses left/middle/right
+ * button events.
+ */
+ if (dev->id.bustype == BUS_AMIGA)
+ return false;
+
+ return true;
+}
static bool joydev_match(struct input_handler *handler, struct input_dev *dev)
{
if (test_bit(EV_KEY, dev->evbit) && test_bit(BTN_DIGI, dev->keybit))
return false;
+ /* Avoid absolute mice */
+ if (joydev_dev_is_absolute_mouse(dev))
+ return false;
+
return true;
}
Say Y here if you are running under control of VMware hypervisor
(ESXi, Workstation or Fusion). Also make sure that when you enable
this option, you remove the xf86-input-vmmouse user-space driver
- or upgrade it to at least xf86-input-vmmouse 13.0.1, which doesn't
+ or upgrade it to at least xf86-input-vmmouse 13.1.0, which doesn't
load in the presence of an in-kernel vmmouse driver.
If unsure, say N.
case V7_PACKET_ID_TWO:
mt[1].x &= ~0x000F;
mt[1].y |= 0x000F;
+ /* Detect false-postive touches where x & y report max value */
+ if (mt[1].y == 0x7ff && mt[1].x == 0xff0) {
+ mt[1].x = 0;
+ /* y gets set to 0 at the end of this function */
+ }
break;
case V7_PACKET_ID_MULTI:
unsigned int x2, unsigned int y2)
{
elantech_set_slot(dev, 0, num_fingers != 0, x1, y1);
- elantech_set_slot(dev, 1, num_fingers == 2, x2, y2);
+ elantech_set_slot(dev, 1, num_fingers >= 2, x2, y2);
}
/*
STMPE_TSC_CTRL_TSC_EN, STMPE_TSC_CTRL_TSC_EN);
/* start polling for touch_det to detect release */
- schedule_delayed_work(&ts->work, HZ / 50);
+ schedule_delayed_work(&ts->work, msecs_to_jiffies(50));
return IRQ_HANDLED;
}
return -ENOMEM;
input = devm_input_allocate_device(&client->dev);
- if (!sx8654)
+ if (!input)
return -ENOMEM;
input->name = "SX8654 I2C Touchscreen";
static void put_pasid_state_wait(struct pasid_state *pasid_state)
{
+ atomic_dec(&pasid_state->count);
wait_event(pasid_state->wq, !atomic_read(&pasid_state->count));
free_pasid_state(pasid_state);
}
#define RESUME_TERMINATE (1 << 0)
#define TTBCR2_SEP_SHIFT 15
-#define TTBCR2_SEP_MASK 0x7
-
-#define TTBCR2_ADDR_32 0
-#define TTBCR2_ADDR_36 1
-#define TTBCR2_ADDR_40 2
-#define TTBCR2_ADDR_42 3
-#define TTBCR2_ADDR_44 4
-#define TTBCR2_ADDR_48 5
+#define TTBCR2_SEP_UPSTREAM (0x7 << TTBCR2_SEP_SHIFT)
#define TTBRn_HI_ASID_SHIFT 16
writel_relaxed(reg, cb_base + ARM_SMMU_CB_TTBCR);
if (smmu->version > ARM_SMMU_V1) {
reg = pgtbl_cfg->arm_lpae_s1_cfg.tcr >> 32;
- switch (smmu->va_size) {
- case 32:
- reg |= (TTBCR2_ADDR_32 << TTBCR2_SEP_SHIFT);
- break;
- case 36:
- reg |= (TTBCR2_ADDR_36 << TTBCR2_SEP_SHIFT);
- break;
- case 40:
- reg |= (TTBCR2_ADDR_40 << TTBCR2_SEP_SHIFT);
- break;
- case 42:
- reg |= (TTBCR2_ADDR_42 << TTBCR2_SEP_SHIFT);
- break;
- case 44:
- reg |= (TTBCR2_ADDR_44 << TTBCR2_SEP_SHIFT);
- break;
- case 48:
- reg |= (TTBCR2_ADDR_48 << TTBCR2_SEP_SHIFT);
- break;
- }
+ reg |= TTBCR2_SEP_UPSTREAM;
writel_relaxed(reg, cb_base + ARM_SMMU_CB_TTBCR2);
}
} else {
return 0;
}
-#ifdef CONFIG_OF
static const struct of_device_id rk_iommu_dt_ids[] = {
{ .compatible = "rockchip,iommu" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, rk_iommu_dt_ids);
-#endif
static struct platform_driver rk_iommu_driver = {
.probe = rk_iommu_probe,
.remove = rk_iommu_remove,
.driver = {
.name = "rk_iommu",
- .of_match_table = of_match_ptr(rk_iommu_dt_ids),
+ .of_match_table = rk_iommu_dt_ids,
},
};
u64 typer = readq_relaxed(its->base + GITS_TYPER);
u32 ids = GITS_TYPER_DEVBITS(typer);
- order = get_order((1UL << ids) * entry_size);
+ /*
+ * 'order' was initialized earlier to the default page
+ * granule of the the ITS. We can't have an allocation
+ * smaller than that. If the requested allocation
+ * is smaller, round up to the default page granule.
+ */
+ order = max(get_order((1UL << ids) * entry_size),
+ order);
if (order >= MAX_ORDER) {
order = MAX_ORDER - 1;
pr_warn("%s: Device Table too large, reduce its page order to %u\n",
irq_domain_set_hwirq_and_chip(domain, virq + i, hwirq + i,
&tegra_ictlr_chip,
- &info->base[ictlr]);
+ info->base[ictlr]);
}
parent_args = *args;
bool lguest_address_ok(const struct lguest *lg,
unsigned long addr, unsigned long len)
{
- return (addr+len) / PAGE_SIZE < lg->pfn_limit && (addr+len >= addr);
+ return addr+len <= lg->pfn_limit * PAGE_SIZE && (addr+len >= addr);
}
/*
* nr_pending is 0 and In_sync is clear, the entries we return will
* still be in the same position on the list when we re-enter
* list_for_each_entry_continue_rcu.
+ *
+ * Note that if entered with 'rdev == NULL' to start at the
+ * beginning, we temporarily assign 'rdev' to an address which
+ * isn't really an rdev, but which can be used by
+ * list_for_each_entry_continue_rcu() to find the first entry.
*/
rcu_read_lock();
if (rdev == NULL)
/* start at the beginning */
- rdev = list_entry_rcu(&mddev->disks, struct md_rdev, same_set);
+ rdev = list_entry(&mddev->disks, struct md_rdev, same_set);
else {
/* release the previous rdev and start from there. */
rdev_dec_pending(rdev, mddev);
if (!mddev->pers || !mddev->pers->sync_request)
return -EINVAL;
- if (cmd_match(page, "frozen"))
- set_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
- else
- clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
if (cmd_match(page, "idle") || cmd_match(page, "frozen")) {
+ if (cmd_match(page, "frozen"))
+ set_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
+ else
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
flush_workqueue(md_misc_wq);
if (mddev->sync_thread) {
set_bit(MD_RECOVERY_INTR, &mddev->recovery);
test_bit(MD_RECOVERY_NEEDED, &mddev->recovery))
return -EBUSY;
else if (cmd_match(page, "resync"))
- set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
else if (cmd_match(page, "recover")) {
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
set_bit(MD_RECOVERY_RECOVER, &mddev->recovery);
- set_bit(MD_RECOVERY_NEEDED, &mddev->recovery);
} else if (cmd_match(page, "reshape")) {
int err;
if (mddev->pers->start_reshape == NULL)
return -EINVAL;
err = mddev_lock(mddev);
if (!err) {
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
err = mddev->pers->start_reshape(mddev);
mddev_unlock(mddev);
}
set_bit(MD_RECOVERY_CHECK, &mddev->recovery);
else if (!cmd_match(page, "repair"))
return -EINVAL;
+ clear_bit(MD_RECOVERY_FROZEN, &mddev->recovery);
set_bit(MD_RECOVERY_REQUESTED, &mddev->recovery);
set_bit(MD_RECOVERY_SYNC, &mddev->recovery);
}
}
dev[j] = rdev1;
- disk_stack_limits(mddev->gendisk, rdev1->bdev,
- rdev1->data_offset << 9);
+ if (mddev->queue)
+ disk_stack_limits(mddev->gendisk, rdev1->bdev,
+ rdev1->data_offset << 9);
if (rdev1->bdev->bd_disk->queue->merge_bvec_fn)
conf->has_merge_bvec = 1;
? (sector & (chunk_sects-1))
: sector_div(sector, chunk_sects));
+ /* Restore due to sector_div */
+ sector = bio->bi_iter.bi_sector;
+
if (sectors < bio_sectors(bio)) {
split = bio_split(bio, sectors, GFP_NOIO, fs_bio_set);
bio_chain(split, bio);
split = bio;
}
- sector = bio->bi_iter.bi_sector;
zone = find_zone(mddev->private, §or);
tmp_dev = map_sector(mddev, zone, sector, §or);
split->bi_bdev = tmp_dev->bdev;
static bool stripe_can_batch(struct stripe_head *sh)
{
return test_bit(STRIPE_BATCH_READY, &sh->state) &&
+ !test_bit(STRIPE_BITMAP_PENDING, &sh->state) &&
is_full_stripe_write(sh);
}
< IO_THRESHOLD)
md_wakeup_thread(conf->mddev->thread);
+ if (test_and_clear_bit(STRIPE_BIT_DELAY, &sh->state)) {
+ int seq = sh->bm_seq;
+ if (test_bit(STRIPE_BIT_DELAY, &sh->batch_head->state) &&
+ sh->batch_head->bm_seq > seq)
+ seq = sh->batch_head->bm_seq;
+ set_bit(STRIPE_BIT_DELAY, &sh->batch_head->state);
+ sh->batch_head->bm_seq = seq;
+ }
+
atomic_inc(&sh->count);
unlock_out:
unlock_two_stripes(head, sh);
pr_debug("skip op %ld on disc %d for sector %llu\n",
bi->bi_rw, i, (unsigned long long)sh->sector);
clear_bit(R5_LOCKED, &sh->dev[i].flags);
- if (sh->batch_head)
- set_bit(STRIPE_BATCH_ERR,
- &sh->batch_head->state);
set_bit(STRIPE_HANDLE, &sh->state);
}
} else
init_async_submit(&submit, 0, tx, NULL, NULL,
to_addr_conv(sh, percpu, j));
- async_gen_syndrome(blocks, 0, count+2, STRIPE_SIZE, &submit);
+ tx = async_gen_syndrome(blocks, 0, count+2, STRIPE_SIZE, &submit);
if (!last_stripe) {
j++;
sh = list_first_entry(&sh->batch_list, struct stripe_head,
put_cpu();
}
+static struct stripe_head *alloc_stripe(struct kmem_cache *sc, gfp_t gfp)
+{
+ struct stripe_head *sh;
+
+ sh = kmem_cache_zalloc(sc, gfp);
+ if (sh) {
+ spin_lock_init(&sh->stripe_lock);
+ spin_lock_init(&sh->batch_lock);
+ INIT_LIST_HEAD(&sh->batch_list);
+ INIT_LIST_HEAD(&sh->lru);
+ atomic_set(&sh->count, 1);
+ }
+ return sh;
+}
static int grow_one_stripe(struct r5conf *conf, gfp_t gfp)
{
struct stripe_head *sh;
- sh = kmem_cache_zalloc(conf->slab_cache, gfp);
+
+ sh = alloc_stripe(conf->slab_cache, gfp);
if (!sh)
return 0;
sh->raid_conf = conf;
- spin_lock_init(&sh->stripe_lock);
-
if (grow_buffers(sh, gfp)) {
shrink_buffers(sh);
kmem_cache_free(conf->slab_cache, sh);
sh->hash_lock_index =
conf->max_nr_stripes % NR_STRIPE_HASH_LOCKS;
/* we just created an active stripe so... */
- atomic_set(&sh->count, 1);
atomic_inc(&conf->active_stripes);
- INIT_LIST_HEAD(&sh->lru);
- spin_lock_init(&sh->batch_lock);
- INIT_LIST_HEAD(&sh->batch_list);
- sh->batch_head = NULL;
release_stripe(sh);
conf->max_nr_stripes++;
return 1;
return ret;
}
+static int resize_chunks(struct r5conf *conf, int new_disks, int new_sectors)
+{
+ unsigned long cpu;
+ int err = 0;
+
+ mddev_suspend(conf->mddev);
+ get_online_cpus();
+ for_each_present_cpu(cpu) {
+ struct raid5_percpu *percpu;
+ struct flex_array *scribble;
+
+ percpu = per_cpu_ptr(conf->percpu, cpu);
+ scribble = scribble_alloc(new_disks,
+ new_sectors / STRIPE_SECTORS,
+ GFP_NOIO);
+
+ if (scribble) {
+ flex_array_free(percpu->scribble);
+ percpu->scribble = scribble;
+ } else {
+ err = -ENOMEM;
+ break;
+ }
+ }
+ put_online_cpus();
+ mddev_resume(conf->mddev);
+ return err;
+}
+
static int resize_stripes(struct r5conf *conf, int newsize)
{
/* Make all the stripes able to hold 'newsize' devices.
struct stripe_head *osh, *nsh;
LIST_HEAD(newstripes);
struct disk_info *ndisks;
- unsigned long cpu;
int err;
struct kmem_cache *sc;
int i;
return -ENOMEM;
for (i = conf->max_nr_stripes; i; i--) {
- nsh = kmem_cache_zalloc(sc, GFP_KERNEL);
+ nsh = alloc_stripe(sc, GFP_KERNEL);
if (!nsh)
break;
nsh->raid_conf = conf;
- spin_lock_init(&nsh->stripe_lock);
-
list_add(&nsh->lru, &newstripes);
}
if (i) {
lock_device_hash_lock(conf, hash));
osh = get_free_stripe(conf, hash);
unlock_device_hash_lock(conf, hash);
- atomic_set(&nsh->count, 1);
+
for(i=0; i<conf->pool_size; i++) {
nsh->dev[i].page = osh->dev[i].page;
nsh->dev[i].orig_page = osh->dev[i].page;
}
- for( ; i<newsize; i++)
- nsh->dev[i].page = NULL;
nsh->hash_lock_index = hash;
kmem_cache_free(conf->slab_cache, osh);
cnt++;
} else
err = -ENOMEM;
- get_online_cpus();
- for_each_present_cpu(cpu) {
- struct raid5_percpu *percpu;
- struct flex_array *scribble;
-
- percpu = per_cpu_ptr(conf->percpu, cpu);
- scribble = scribble_alloc(newsize, conf->chunk_sectors /
- STRIPE_SECTORS, GFP_NOIO);
-
- if (scribble) {
- flex_array_free(percpu->scribble);
- percpu->scribble = scribble;
- } else {
- err = -ENOMEM;
- break;
- }
- }
- put_online_cpus();
-
/* Step 4, return new stripes to service */
while(!list_empty(&newstripes)) {
nsh = list_entry(newstripes.next, struct stripe_head, lru);
conf->slab_cache = sc;
conf->active_name = 1-conf->active_name;
- conf->pool_size = newsize;
+ if (!err)
+ conf->pool_size = newsize;
return err;
}
}
rdev_dec_pending(rdev, conf->mddev);
- if (sh->batch_head && !uptodate)
+ if (sh->batch_head && !uptodate && !replacement)
set_bit(STRIPE_BATCH_ERR, &sh->batch_head->state);
if (!test_and_clear_bit(R5_DOUBLE_LOCKED, &sh->dev[i].flags))
pr_debug("added bi b#%llu to stripe s#%llu, disk %d.\n",
(unsigned long long)(*bip)->bi_iter.bi_sector,
(unsigned long long)sh->sector, dd_idx);
- spin_unlock_irq(&sh->stripe_lock);
if (conf->mddev->bitmap && firstwrite) {
+ /* Cannot hold spinlock over bitmap_startwrite,
+ * but must ensure this isn't added to a batch until
+ * we have added to the bitmap and set bm_seq.
+ * So set STRIPE_BITMAP_PENDING to prevent
+ * batching.
+ * If multiple add_stripe_bio() calls race here they
+ * much all set STRIPE_BITMAP_PENDING. So only the first one
+ * to complete "bitmap_startwrite" gets to set
+ * STRIPE_BIT_DELAY. This is important as once a stripe
+ * is added to a batch, STRIPE_BIT_DELAY cannot be changed
+ * any more.
+ */
+ set_bit(STRIPE_BITMAP_PENDING, &sh->state);
+ spin_unlock_irq(&sh->stripe_lock);
bitmap_startwrite(conf->mddev->bitmap, sh->sector,
STRIPE_SECTORS, 0);
- sh->bm_seq = conf->seq_flush+1;
- set_bit(STRIPE_BIT_DELAY, &sh->state);
+ spin_lock_irq(&sh->stripe_lock);
+ clear_bit(STRIPE_BITMAP_PENDING, &sh->state);
+ if (!sh->batch_head) {
+ sh->bm_seq = conf->seq_flush+1;
+ set_bit(STRIPE_BIT_DELAY, &sh->state);
+ }
}
+ spin_unlock_irq(&sh->stripe_lock);
if (stripe_can_batch(sh))
stripe_add_to_batch_list(conf, sh);
/* reconstruct-write isn't being forced */
return 0;
for (i = 0; i < s->failed; i++) {
- if (!test_bit(R5_UPTODATE, &fdev[i]->flags) &&
+ if (s->failed_num[i] != sh->pd_idx &&
+ s->failed_num[i] != sh->qd_idx &&
+ !test_bit(R5_UPTODATE, &fdev[i]->flags) &&
!test_bit(R5_OVERWRITE, &fdev[i]->flags))
return 1;
}
*/
BUG_ON(test_bit(R5_Wantcompute, &dev->flags));
BUG_ON(test_bit(R5_Wantread, &dev->flags));
+ BUG_ON(sh->batch_head);
if ((s->uptodate == disks - 1) &&
(s->failed && (disk_idx == s->failed_num[0] ||
disk_idx == s->failed_num[1]))) {
{
int i;
- BUG_ON(sh->batch_head);
/* look for blocks to read/compute, skip this if a compute
* is already in flight, or if the stripe contents are in the
* midst of changing due to a write
set_bit(STRIPE_HANDLE, &sh->state);
}
+static void break_stripe_batch_list(struct stripe_head *head_sh,
+ unsigned long handle_flags);
/* handle_stripe_clean_event
* any written block on an uptodate or failed drive can be returned.
* Note that if we 'wrote' to a failed drive, it will be UPTODATE, but
int discard_pending = 0;
struct stripe_head *head_sh = sh;
bool do_endio = false;
- int wakeup_nr = 0;
for (i = disks; i--; )
if (sh->dev[i].written) {
if (atomic_dec_and_test(&conf->pending_full_writes))
md_wakeup_thread(conf->mddev->thread);
- if (!head_sh->batch_head || !do_endio)
- return;
- for (i = 0; i < head_sh->disks; i++) {
- if (test_and_clear_bit(R5_Overlap, &head_sh->dev[i].flags))
- wakeup_nr++;
- }
- while (!list_empty(&head_sh->batch_list)) {
- int i;
- sh = list_first_entry(&head_sh->batch_list,
- struct stripe_head, batch_list);
- list_del_init(&sh->batch_list);
-
- set_mask_bits(&sh->state, ~STRIPE_EXPAND_SYNC_FLAG,
- head_sh->state & ~((1 << STRIPE_ACTIVE) |
- (1 << STRIPE_PREREAD_ACTIVE) |
- STRIPE_EXPAND_SYNC_FLAG));
- sh->check_state = head_sh->check_state;
- sh->reconstruct_state = head_sh->reconstruct_state;
- for (i = 0; i < sh->disks; i++) {
- if (test_and_clear_bit(R5_Overlap, &sh->dev[i].flags))
- wakeup_nr++;
- sh->dev[i].flags = head_sh->dev[i].flags;
- }
-
- spin_lock_irq(&sh->stripe_lock);
- sh->batch_head = NULL;
- spin_unlock_irq(&sh->stripe_lock);
- if (sh->state & STRIPE_EXPAND_SYNC_FLAG)
- set_bit(STRIPE_HANDLE, &sh->state);
- release_stripe(sh);
- }
-
- spin_lock_irq(&head_sh->stripe_lock);
- head_sh->batch_head = NULL;
- spin_unlock_irq(&head_sh->stripe_lock);
- wake_up_nr(&conf->wait_for_overlap, wakeup_nr);
- if (head_sh->state & STRIPE_EXPAND_SYNC_FLAG)
- set_bit(STRIPE_HANDLE, &head_sh->state);
+ if (head_sh->batch_head && do_endio)
+ break_stripe_batch_list(head_sh, STRIPE_EXPAND_SYNC_FLAGS);
}
static void handle_stripe_dirtying(struct r5conf *conf,
static int clear_batch_ready(struct stripe_head *sh)
{
+ /* Return '1' if this is a member of batch, or
+ * '0' if it is a lone stripe or a head which can now be
+ * handled.
+ */
struct stripe_head *tmp;
if (!test_and_clear_bit(STRIPE_BATCH_READY, &sh->state))
- return 0;
+ return (sh->batch_head && sh->batch_head != sh);
spin_lock(&sh->stripe_lock);
if (!sh->batch_head) {
spin_unlock(&sh->stripe_lock);
return 0;
}
-static void check_break_stripe_batch_list(struct stripe_head *sh)
+static void break_stripe_batch_list(struct stripe_head *head_sh,
+ unsigned long handle_flags)
{
- struct stripe_head *head_sh, *next;
+ struct stripe_head *sh, *next;
int i;
+ int do_wakeup = 0;
- if (!test_and_clear_bit(STRIPE_BATCH_ERR, &sh->state))
- return;
+ list_for_each_entry_safe(sh, next, &head_sh->batch_list, batch_list) {
- head_sh = sh;
- do {
- sh = list_first_entry(&sh->batch_list,
- struct stripe_head, batch_list);
- BUG_ON(sh == head_sh);
- } while (!test_bit(STRIPE_DEGRADED, &sh->state));
-
- while (sh != head_sh) {
- next = list_first_entry(&sh->batch_list,
- struct stripe_head, batch_list);
list_del_init(&sh->batch_list);
- set_mask_bits(&sh->state, ~STRIPE_EXPAND_SYNC_FLAG,
- head_sh->state & ~((1 << STRIPE_ACTIVE) |
- (1 << STRIPE_PREREAD_ACTIVE) |
- (1 << STRIPE_DEGRADED) |
- STRIPE_EXPAND_SYNC_FLAG));
+ WARN_ON_ONCE(sh->state & ((1 << STRIPE_ACTIVE) |
+ (1 << STRIPE_SYNCING) |
+ (1 << STRIPE_REPLACED) |
+ (1 << STRIPE_PREREAD_ACTIVE) |
+ (1 << STRIPE_DELAYED) |
+ (1 << STRIPE_BIT_DELAY) |
+ (1 << STRIPE_FULL_WRITE) |
+ (1 << STRIPE_BIOFILL_RUN) |
+ (1 << STRIPE_COMPUTE_RUN) |
+ (1 << STRIPE_OPS_REQ_PENDING) |
+ (1 << STRIPE_DISCARD) |
+ (1 << STRIPE_BATCH_READY) |
+ (1 << STRIPE_BATCH_ERR) |
+ (1 << STRIPE_BITMAP_PENDING)));
+ WARN_ON_ONCE(head_sh->state & ((1 << STRIPE_DISCARD) |
+ (1 << STRIPE_REPLACED)));
+
+ set_mask_bits(&sh->state, ~(STRIPE_EXPAND_SYNC_FLAGS |
+ (1 << STRIPE_DEGRADED)),
+ head_sh->state & (1 << STRIPE_INSYNC));
+
sh->check_state = head_sh->check_state;
sh->reconstruct_state = head_sh->reconstruct_state;
- for (i = 0; i < sh->disks; i++)
+ for (i = 0; i < sh->disks; i++) {
+ if (test_and_clear_bit(R5_Overlap, &sh->dev[i].flags))
+ do_wakeup = 1;
sh->dev[i].flags = head_sh->dev[i].flags &
(~((1 << R5_WriteError) | (1 << R5_Overlap)));
-
+ }
spin_lock_irq(&sh->stripe_lock);
sh->batch_head = NULL;
spin_unlock_irq(&sh->stripe_lock);
-
- set_bit(STRIPE_HANDLE, &sh->state);
+ if (handle_flags == 0 ||
+ sh->state & handle_flags)
+ set_bit(STRIPE_HANDLE, &sh->state);
release_stripe(sh);
-
- sh = next;
}
+ spin_lock_irq(&head_sh->stripe_lock);
+ head_sh->batch_head = NULL;
+ spin_unlock_irq(&head_sh->stripe_lock);
+ for (i = 0; i < head_sh->disks; i++)
+ if (test_and_clear_bit(R5_Overlap, &head_sh->dev[i].flags))
+ do_wakeup = 1;
+ if (head_sh->state & handle_flags)
+ set_bit(STRIPE_HANDLE, &head_sh->state);
+
+ if (do_wakeup)
+ wake_up(&head_sh->raid_conf->wait_for_overlap);
}
static void handle_stripe(struct stripe_head *sh)
return;
}
- check_break_stripe_batch_list(sh);
+ if (test_and_clear_bit(STRIPE_BATCH_ERR, &sh->state))
+ break_stripe_batch_list(sh, 0);
if (test_bit(STRIPE_SYNC_REQUESTED, &sh->state) && !sh->batch_head) {
spin_lock(&sh->stripe_lock);
if (s.failed > conf->max_degraded) {
sh->check_state = 0;
sh->reconstruct_state = 0;
+ break_stripe_batch_list(sh, 0);
if (s.to_read+s.to_write+s.written)
handle_failed_stripe(conf, sh, &s, disks, &s.return_bi);
if (s.syncing + s.replacing)
percpu->spare_page = alloc_page(GFP_KERNEL);
if (!percpu->scribble)
percpu->scribble = scribble_alloc(max(conf->raid_disks,
- conf->previous_raid_disks), conf->chunk_sectors /
- STRIPE_SECTORS, GFP_KERNEL);
+ conf->previous_raid_disks),
+ max(conf->chunk_sectors,
+ conf->prev_chunk_sectors)
+ / STRIPE_SECTORS,
+ GFP_KERNEL);
if (!percpu->scribble || (conf->level == 6 && !percpu->spare_page)) {
free_scratch_buffer(conf, percpu);
if (!check_stripe_cache(mddev))
return -ENOSPC;
+ if (mddev->new_chunk_sectors > mddev->chunk_sectors ||
+ mddev->delta_disks > 0)
+ if (resize_chunks(conf,
+ conf->previous_raid_disks
+ + max(0, mddev->delta_disks),
+ max(mddev->new_chunk_sectors,
+ mddev->chunk_sectors)
+ ) < 0)
+ return -ENOMEM;
return resize_stripes(conf, (conf->previous_raid_disks
+ mddev->delta_disks));
}
STRIPE_ON_RELEASE_LIST,
STRIPE_BATCH_READY,
STRIPE_BATCH_ERR,
+ STRIPE_BITMAP_PENDING, /* Being added to bitmap, don't add
+ * to batch yet.
+ */
};
-#define STRIPE_EXPAND_SYNC_FLAG \
+#define STRIPE_EXPAND_SYNC_FLAGS \
((1 << STRIPE_EXPAND_SOURCE) |\
(1 << STRIPE_EXPAND_READY) |\
(1 << STRIPE_EXPANDING) |\
EXPORT_SYMBOL_GPL(da9052_adc_read_temp);
static const struct mfd_cell da9052_subdev_info[] = {
+ {
+ .name = "da9052-regulator",
+ .id = 0,
+ },
{
.name = "da9052-regulator",
.id = 1,
.name = "da9052-regulator",
.id = 13,
},
- {
- .name = "da9052-regulator",
- .id = 14,
- },
{
.name = "da9052-onkey",
},
if (ios->clock) {
unsigned int clock_min = ~0U;
- u32 clkdiv;
+ int clkdiv;
spin_lock_bh(&host->lock);
if (!host->mode_reg) {
/* Calculate clock divider */
if (host->caps.has_odd_clk_div) {
clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
- if (clkdiv > 511) {
+ if (clkdiv < 0) {
+ dev_warn(&mmc->class_dev,
+ "clock %u too fast; using %lu\n",
+ clock_min, host->bus_hz / 2);
+ clkdiv = 0;
+ } else if (clkdiv > 511) {
dev_warn(&mmc->class_dev,
"clock %u too slow; using %lu\n",
clock_min, host->bus_hz / (511 + 2));
*/
if (data && data->type)
flash_name = data->type;
- else if (!strcmp(spi->modalias, "nor-jedec"))
+ else if (!strcmp(spi->modalias, "spi-nor"))
flash_name = NULL; /* auto-detect */
else
flash_name = spi->modalias;
* since most of these flash are compatible to some extent, and their
* differences can often be differentiated by the JEDEC read-ID command, we
* encourage new users to add support to the spi-nor library, and simply bind
- * against a generic string here (e.g., "nor-jedec").
+ * against a generic string here (e.g., "jedec,spi-nor").
*
* Many flash names are kept here in this list (as well as in spi-nor.c) to
* keep them available as module aliases for existing platforms.
* Generic support for SPI NOR that can be identified by the JEDEC READ
* ID opcode (0x9F). Use this, if possible.
*/
- {"nor-jedec"},
+ {"spi-nor"},
{ },
};
MODULE_DEVICE_TABLE(spi, m25p_ids);
err = ret;
}
- err = mtdtest_relax();
- if (err)
+ ret = mtdtest_relax();
+ if (ret) {
+ err = ret;
goto out;
+ }
}
if (err)
blk_rq_map_sg(req->q, req, pdu->usgl.sg);
ret = ubiblock_read(pdu);
+ rq_flush_dcache_pages(req);
+
blk_mq_end_request(req, ret);
}
out:
if (ret)
bond_opt_error_interpret(bond, opt, ret, val);
- else
+ else if (bond->dev->reg_state == NETREG_REGISTERED)
call_netdevice_notifiers(NETDEV_CHANGEINFODATA, bond->dev);
return ret;
cf->can_id |= CAN_RTR_FLAG;
}
- if (!(id_xcan & XCAN_IDR_SRR_MASK)) {
- data[0] = priv->read_reg(priv, XCAN_RXFIFO_DW1_OFFSET);
- data[1] = priv->read_reg(priv, XCAN_RXFIFO_DW2_OFFSET);
+ /* DW1/DW2 must always be read to remove message from RXFIFO */
+ data[0] = priv->read_reg(priv, XCAN_RXFIFO_DW1_OFFSET);
+ data[1] = priv->read_reg(priv, XCAN_RXFIFO_DW2_OFFSET);
+ if (!(cf->can_id & CAN_RTR_FLAG)) {
/* Change Xilinx CAN data format to socketCAN data format */
if (cf->can_dlc > 0)
*(__be32 *)(cf->data) = cpu_to_be32(data[0]);
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6171)
unregister_switch_driver(&mv88e6171_switch_driver);
#endif
+#if IS_ENABLED(CONFIG_NET_DSA_MV88E6352)
+ unregister_switch_driver(&mv88e6352_switch_driver);
+#endif
#if IS_ENABLED(CONFIG_NET_DSA_MV88E6123_61_65)
unregister_switch_driver(&mv88e6123_61_65_switch_driver);
#endif
config AMD_XGBE
tristate "AMD 10GbE Ethernet driver"
depends on (OF_NET || ACPI) && HAS_IOMEM && HAS_DMA
+ depends on ARM64 || COMPILE_TEST
select PHYLIB
select AMD_XGBE_PHY
select BITREVERSE
config NET_XGENE
tristate "APM X-Gene SoC Ethernet Driver"
depends on HAS_DMA
+ depends on ARCH_XGENE || COMPILE_TEST
select PHYLIB
help
This is the Ethernet driver for the on-chip ethernet interface on the
{
struct bnx2x *bp = netdev_priv(dev);
+ if (pci_num_vf(bp->pdev)) {
+ DP(BNX2X_MSG_IOV, "VFs are enabled, can not change MTU\n");
+ return -EPERM;
+ }
+
if (bp->recovery_state != BNX2X_RECOVERY_DONE) {
BNX2X_ERR("Can't perform change MTU during parity recovery\n");
return -EAGAIN;
}
bp = netdev_priv(dev);
- if (pci_num_vf(bp->pdev)) {
- DP(BNX2X_MSG_IOV, "VFs are enabled, can not change MTU\n");
- return -EPERM;
- }
-
if (bp->recovery_state != BNX2X_RECOVERY_DONE) {
BNX2X_ERR("Handling parity error recovery. Try again later\n");
return -EAGAIN;
/* Management FW 'remembers' living interfaces. Allow it some time
* to forget previously living interfaces, allowing a proper re-load.
*/
- if (is_kdump_kernel())
- msleep(5000);
+ if (is_kdump_kernel()) {
+ ktime_t now = ktime_get_boottime();
+ ktime_t fw_ready_time = ktime_set(5, 0);
+
+ if (ktime_before(now, fw_ready_time))
+ msleep(ktime_ms_delta(fw_ready_time, now));
+ }
/* An estimated maximum supported CoS number according to the chip
* version.
else
phydev->supported &= PHY_BASIC_FEATURES;
+ if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
+ phydev->supported &= ~SUPPORTED_1000baseT_Half;
+
phydev->advertising = phydev->supported;
bp->link = 0;
struct macb_queue *queue = dev_id;
struct macb *bp = queue->bp;
struct net_device *dev = bp->dev;
- u32 status;
+ u32 status, ctrl;
status = queue_readl(queue, ISR);
* add that if/when we get our hands on a full-blown MII PHY.
*/
+ /* There is a hardware issue under heavy load where DMA can
+ * stop, this causes endless "used buffer descriptor read"
+ * interrupts but it can be cleared by re-enabling RX. See
+ * the at91 manual, section 41.3.1 or the Zynq manual
+ * section 16.7.4 for details.
+ */
+ if (status & MACB_BIT(RXUBR)) {
+ ctrl = macb_readl(bp, NCR);
+ macb_writel(bp, NCR, ctrl & ~MACB_BIT(RE));
+ macb_writel(bp, NCR, ctrl | MACB_BIT(RE));
+
+ if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
+ macb_writel(bp, ISR, MACB_BIT(RXUBR));
+ }
+
if (status & MACB_BIT(ISR_ROVR)) {
/* We missed at least one packet */
if (macb_is_gem(bp))
.init = at91ether_init,
};
+static const struct macb_config zynq_config = {
+ .caps = MACB_CAPS_SG_DISABLED | MACB_CAPS_GIGABIT_MODE_AVAILABLE |
+ MACB_CAPS_NO_GIGABIT_HALF,
+ .dma_burst_length = 16,
+ .clk_init = macb_clk_init,
+ .init = macb_init,
+};
+
static const struct of_device_id macb_dt_ids[] = {
{ .compatible = "cdns,at32ap7000-macb" },
{ .compatible = "cdns,at91sam9260-macb", .data = &at91sam9260_config },
{ .compatible = "atmel,sama5d4-gem", .data = &sama5d4_config },
{ .compatible = "cdns,at91rm9200-emac", .data = &emac_config },
{ .compatible = "cdns,emac", .data = &emac_config },
+ { .compatible = "cdns,zynq-gem", .data = &zynq_config },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, macb_dt_ids);
#define MACB_CAPS_ISR_CLEAR_ON_WRITE 0x00000001
#define MACB_CAPS_USRIO_HAS_CLKEN 0x00000002
#define MACB_CAPS_USRIO_DEFAULT_IS_MII 0x00000004
+#define MACB_CAPS_NO_GIGABIT_HALF 0x00000008
#define MACB_CAPS_FIFO_MODE 0x10000000
#define MACB_CAPS_GIGABIT_MODE_AVAILABLE 0x20000000
#define MACB_CAPS_SG_DISABLED 0x40000000
static int emac_get_regs_len(struct emac_instance *dev)
{
- if (emac_has_feature(dev, EMAC_FTR_EMAC4))
- return sizeof(struct emac_ethtool_regs_subhdr) +
- EMAC4_ETHTOOL_REGS_SIZE(dev);
- else
return sizeof(struct emac_ethtool_regs_subhdr) +
- EMAC_ETHTOOL_REGS_SIZE(dev);
+ sizeof(struct emac_regs);
}
static int emac_ethtool_get_regs_len(struct net_device *ndev)
struct emac_ethtool_regs_subhdr *hdr = buf;
hdr->index = dev->cell_index;
- if (emac_has_feature(dev, EMAC_FTR_EMAC4)) {
+ if (emac_has_feature(dev, EMAC_FTR_EMAC4SYNC)) {
+ hdr->version = EMAC4SYNC_ETHTOOL_REGS_VER;
+ } else if (emac_has_feature(dev, EMAC_FTR_EMAC4)) {
hdr->version = EMAC4_ETHTOOL_REGS_VER;
- memcpy_fromio(hdr + 1, dev->emacp, EMAC4_ETHTOOL_REGS_SIZE(dev));
- return (void *)(hdr + 1) + EMAC4_ETHTOOL_REGS_SIZE(dev);
} else {
hdr->version = EMAC_ETHTOOL_REGS_VER;
- memcpy_fromio(hdr + 1, dev->emacp, EMAC_ETHTOOL_REGS_SIZE(dev));
- return (void *)(hdr + 1) + EMAC_ETHTOOL_REGS_SIZE(dev);
}
+ memcpy_fromio(hdr + 1, dev->emacp, sizeof(struct emac_regs));
+ return (void *)(hdr + 1) + sizeof(struct emac_regs);
}
static void emac_ethtool_get_regs(struct net_device *ndev,
};
#define EMAC_ETHTOOL_REGS_VER 0
-#define EMAC_ETHTOOL_REGS_SIZE(dev) ((dev)->rsrc_regs.end - \
- (dev)->rsrc_regs.start + 1)
-#define EMAC4_ETHTOOL_REGS_VER 1
-#define EMAC4_ETHTOOL_REGS_SIZE(dev) ((dev)->rsrc_regs.end - \
- (dev)->rsrc_regs.start + 1)
+#define EMAC4_ETHTOOL_REGS_VER 1
+#define EMAC4SYNC_ETHTOOL_REGS_VER 2
#endif /* __IBM_NEWEMAC_CORE_H */
#include <linux/ptp_classify.h>
#include <linux/mii.h>
#include <linux/mdio.h>
+#include <linux/pm_qos.h>
#include "hw.h"
struct e1000_info;
unsigned int total_bytes = 0, total_packets = 0;
u16 cleaned_count = fm10k_desc_unused(rx_ring);
- do {
+ while (likely(total_packets < budget)) {
union fm10k_rx_desc *rx_desc;
/* return some buffers to hardware, one at a time is too slow */
/* update budget accounting */
total_packets++;
- } while (likely(total_packets < budget));
+ }
/* place incomplete frames back on ring for completion */
rx_ring->skb = skb;
adapter->tx_ring[q_vector->tx.ring->queue_index] = NULL;
if (q_vector->rx.ring)
- adapter->tx_ring[q_vector->rx.ring->queue_index] = NULL;
+ adapter->rx_ring[q_vector->rx.ring->queue_index] = NULL;
netif_napi_del(&q_vector->napi);
q_vector = adapter->q_vector[v_idx];
if (!q_vector)
q_vector = kzalloc(size, GFP_KERNEL);
+ else
+ memset(q_vector, 0, size);
if (!q_vector)
return -ENOMEM;
u8 *dst_mac = skb_header_pointer(skb, 0, 0, NULL);
if (!dst_mac || is_link_local_ether_addr(dst_mac)) {
- dev_kfree_skb(skb);
+ dev_kfree_skb_any(skb);
return NETDEV_TX_OK;
}
msecs_to_jiffies(timeout))) {
mlx4_warn(dev, "command 0x%x timed out (go bit not cleared)\n",
op);
- err = -EIO;
- goto out_reset;
+ if (op == MLX4_CMD_NOP) {
+ err = -EBUSY;
+ goto out;
+ } else {
+ err = -EIO;
+ goto out_reset;
+ }
}
err = context->result;
int i;
int offset = next - start;
- for (i = 0; i <= num; i++) {
+ for (i = 0; i < num; i++) {
ret += be64_to_cpu(*curr);
curr += offset;
}
{
int err;
int eqn = vhcr->in_modifier;
- int res_id = (slave << 8) | eqn;
+ int res_id = (slave << 10) | eqn;
struct mlx4_eq_context *eqc = inbox->buf;
int mtt_base = eq_get_mtt_addr(eqc) / dev->caps.mtt_entry_sz;
int mtt_size = eq_get_mtt_size(eqc);
struct mlx4_cmd_info *cmd)
{
int eqn = vhcr->in_modifier;
- int res_id = eqn | (slave << 8);
+ int res_id = eqn | (slave << 10);
struct res_eq *eq;
int err;
return 0;
mutex_lock(&priv->mfunc.master.gen_eqe_mutex[slave]);
- res_id = (slave << 8) | event_eq->eqn;
+ res_id = (slave << 10) | event_eq->eqn;
err = get_res(dev, slave, res_id, RES_EQ, &req);
if (err)
goto unlock;
memcpy(mailbox->buf, (u8 *) eqe, 28);
- in_modifier = (slave & 0xff) | ((event_eq->eqn & 0xff) << 16);
+ in_modifier = (slave & 0xff) | ((event_eq->eqn & 0x3ff) << 16);
err = mlx4_cmd(dev, mailbox->dma, in_modifier, 0,
MLX4_CMD_GEN_EQE, MLX4_CMD_TIME_CLASS_B,
struct mlx4_cmd_info *cmd)
{
int eqn = vhcr->in_modifier;
- int res_id = eqn | (slave << 8);
+ int res_id = eqn | (slave << 10);
struct res_eq *eq;
int err;
int cqn = vhcr->in_modifier;
struct mlx4_cq_context *cqc = inbox->buf;
int mtt_base = cq_get_mtt_addr(cqc) / dev->caps.mtt_entry_sz;
- struct res_cq *cq;
+ struct res_cq *cq = NULL;
struct res_mtt *mtt;
err = cq_res_start_move_to(dev, slave, cqn, RES_CQ_HW, &cq);
{
int err;
int cqn = vhcr->in_modifier;
- struct res_cq *cq;
+ struct res_cq *cq = NULL;
err = cq_res_start_move_to(dev, slave, cqn, RES_CQ_ALLOCATED, &cq);
if (err)
int err;
int srqn = vhcr->in_modifier;
struct res_mtt *mtt;
- struct res_srq *srq;
+ struct res_srq *srq = NULL;
struct mlx4_srq_context *srqc = inbox->buf;
int mtt_base = srq_get_mtt_addr(srqc) / dev->caps.mtt_entry_sz;
{
int err;
int srqn = vhcr->in_modifier;
- struct res_srq *srq;
+ struct res_srq *srq = NULL;
err = srq_res_start_move_to(dev, slave, srqn, RES_SRQ_ALLOCATED, &srq);
if (err)
break;
case RES_EQ_HW:
- err = mlx4_cmd(dev, slave, eqn & 0xff,
+ err = mlx4_cmd(dev, slave, eqn & 0x3ff,
1, MLX4_CMD_HW2SW_EQ,
MLX4_CMD_TIME_CLASS_A,
MLX4_CMD_NATIVE);
if (err)
mlx4_dbg(dev, "rem_slave_eqs: failed to move slave %d eqs %d to SW ownership\n",
- slave, eqn);
+ slave, eqn & 0x3ff);
atomic_dec(&eq->mtt->ref_count);
state = RES_EQ_RESERVED;
break;
int done = 0;
struct nx_host_tx_ring *tx_ring = adapter->tx_ring;
- if (!spin_trylock(&adapter->tx_clean_lock))
+ if (!spin_trylock_bh(&adapter->tx_clean_lock))
return 1;
sw_consumer = tx_ring->sw_consumer;
*/
hw_consumer = le32_to_cpu(*(tx_ring->hw_consumer));
done = (sw_consumer == hw_consumer);
- spin_unlock(&adapter->tx_clean_lock);
+ spin_unlock_bh(&adapter->tx_clean_lock);
return done;
}
u8 dw, rows, cols, banks, ranks;
u32 val;
- if (size != sizeof(struct netxen_dimm_cfg)) {
+ if (size < attr->size) {
netdev_err(netdev, "Invalid size\n");
- return -1;
+ return -EINVAL;
}
memset(&dimm, 0, sizeof(struct netxen_dimm_cfg));
static struct bin_attribute bin_attr_dimm = {
.attr = { .name = "dimm", .mode = (S_IRUGO | S_IWUSR) },
- .size = 0,
+ .size = sizeof(struct netxen_dimm_cfg),
.read = netxen_sysfs_read_dimm,
};
qca->spi_dev = spi_device;
qca->legacy_mode = legacy_mode;
+ spi_set_drvdata(spi_device, qcaspi_devs);
+
mac = of_get_mac_address(spi_device->dev.of_node);
if (mac)
return -EFAULT;
}
- spi_set_drvdata(spi_device, qcaspi_devs);
-
qcaspi_init_device_debugfs(qca);
return 0;
rtl8169_start_xmit(nskb, tp->dev);
} while (segs);
- dev_kfree_skb(skb);
+ dev_consume_skb_any(skb);
} else if (skb->ip_summed == CHECKSUM_PARTIAL) {
if (skb_checksum_help(skb) < 0)
goto drop;
drop:
stats = &tp->dev->stats;
stats->tx_dropped++;
- dev_kfree_skb(skb);
+ dev_kfree_skb_any(skb);
}
}
struct neighbour *n = __ipv4_neigh_lookup(dev, (__force u32)ip_addr);
int err = 0;
- if (!n)
+ if (!n) {
n = neigh_create(&arp_tbl, &ip_addr, dev);
- if (!n)
- return -ENOMEM;
+ if (IS_ERR(n))
+ return IS_ERR(n);
+ }
/* If the neigh is already resolved, then go ahead and
* install the entry, otherwise start the ARP process to
else
neigh_event_send(n, NULL);
+ neigh_release(n);
return err;
}
const struct of_device_id *match = NULL;
struct smc_local *lp;
struct net_device *ndev;
- struct resource *res, *ires;
+ struct resource *res;
unsigned int __iomem *addr;
unsigned long irq_flags = SMC_IRQ_FLAGS;
+ unsigned long irq_resflags;
int ret;
ndev = alloc_etherdev(sizeof(struct smc_local));
goto out_free_netdev;
}
- ires = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
- if (!ires) {
+ ndev->irq = platform_get_irq(pdev, 0);
+ if (ndev->irq <= 0) {
ret = -ENODEV;
goto out_release_io;
}
-
- ndev->irq = ires->start;
-
- if (irq_flags == -1 || ires->flags & IRQF_TRIGGER_MASK)
- irq_flags = ires->flags & IRQF_TRIGGER_MASK;
+ /*
+ * If this platform does not specify any special irqflags, or if
+ * the resource supplies a trigger, override the irqflags with
+ * the trigger flags from the resource.
+ */
+ irq_resflags = irqd_get_trigger_type(irq_get_irq_data(ndev->irq));
+ if (irq_flags == -1 || irq_resflags & IRQF_TRIGGER_MASK)
+ irq_flags = irq_resflags & IRQF_TRIGGER_MASK;
ret = smc_request_attrib(pdev, ndev);
if (ret)
struct net_device *dev;
struct smsc911x_data *pdata;
struct smsc911x_platform_config *config = dev_get_platdata(&pdev->dev);
- struct resource *res, *irq_res;
+ struct resource *res;
unsigned int intcfg = 0;
- int res_size, irq_flags;
+ int res_size, irq, irq_flags;
int retval;
res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
}
res_size = resource_size(res);
- irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
- if (!irq_res) {
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
pr_warn("Could not allocate irq resource\n");
retval = -ENODEV;
goto out_0;
SET_NETDEV_DEV(dev, &pdev->dev);
pdata = netdev_priv(dev);
- dev->irq = irq_res->start;
- irq_flags = irq_res->flags & IRQF_TRIGGER_MASK;
+ dev->irq = irq;
+ irq_flags = irq_get_trigger_type(irq);
pdata->ioaddr = ioremap_nocache(res->start, res_size);
pdata->dev = dev;
int use_riwt;
int irq_wake;
spinlock_t ptp_lock;
+
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *dbgfs_dir;
+ struct dentry *dbgfs_rings_status;
+ struct dentry *dbgfs_dma_cap;
+#endif
};
int stmmac_mdio_unregister(struct net_device *ndev);
#ifdef CONFIG_DEBUG_FS
static int stmmac_init_fs(struct net_device *dev);
-static void stmmac_exit_fs(void);
+static void stmmac_exit_fs(struct net_device *dev);
#endif
#define STMMAC_COAL_TIMER(x) (jiffies + usecs_to_jiffies(x))
netif_carrier_off(dev);
#ifdef CONFIG_DEBUG_FS
- stmmac_exit_fs();
+ stmmac_exit_fs(dev);
#endif
stmmac_release_ptp(priv);
#ifdef CONFIG_DEBUG_FS
static struct dentry *stmmac_fs_dir;
-static struct dentry *stmmac_rings_status;
-static struct dentry *stmmac_dma_cap;
static void sysfs_display_ring(void *head, int size, int extend_desc,
struct seq_file *seq)
static int stmmac_init_fs(struct net_device *dev)
{
- /* Create debugfs entries */
- stmmac_fs_dir = debugfs_create_dir(STMMAC_RESOURCE_NAME, NULL);
+ struct stmmac_priv *priv = netdev_priv(dev);
+
+ /* Create per netdev entries */
+ priv->dbgfs_dir = debugfs_create_dir(dev->name, stmmac_fs_dir);
- if (!stmmac_fs_dir || IS_ERR(stmmac_fs_dir)) {
- pr_err("ERROR %s, debugfs create directory failed\n",
- STMMAC_RESOURCE_NAME);
+ if (!priv->dbgfs_dir || IS_ERR(priv->dbgfs_dir)) {
+ pr_err("ERROR %s/%s, debugfs create directory failed\n",
+ STMMAC_RESOURCE_NAME, dev->name);
return -ENOMEM;
}
/* Entry to report DMA RX/TX rings */
- stmmac_rings_status = debugfs_create_file("descriptors_status",
- S_IRUGO, stmmac_fs_dir, dev,
- &stmmac_rings_status_fops);
+ priv->dbgfs_rings_status =
+ debugfs_create_file("descriptors_status", S_IRUGO,
+ priv->dbgfs_dir, dev,
+ &stmmac_rings_status_fops);
- if (!stmmac_rings_status || IS_ERR(stmmac_rings_status)) {
+ if (!priv->dbgfs_rings_status || IS_ERR(priv->dbgfs_rings_status)) {
pr_info("ERROR creating stmmac ring debugfs file\n");
- debugfs_remove(stmmac_fs_dir);
+ debugfs_remove_recursive(priv->dbgfs_dir);
return -ENOMEM;
}
/* Entry to report the DMA HW features */
- stmmac_dma_cap = debugfs_create_file("dma_cap", S_IRUGO, stmmac_fs_dir,
- dev, &stmmac_dma_cap_fops);
+ priv->dbgfs_dma_cap = debugfs_create_file("dma_cap", S_IRUGO,
+ priv->dbgfs_dir,
+ dev, &stmmac_dma_cap_fops);
- if (!stmmac_dma_cap || IS_ERR(stmmac_dma_cap)) {
+ if (!priv->dbgfs_dma_cap || IS_ERR(priv->dbgfs_dma_cap)) {
pr_info("ERROR creating stmmac MMC debugfs file\n");
- debugfs_remove(stmmac_rings_status);
- debugfs_remove(stmmac_fs_dir);
+ debugfs_remove_recursive(priv->dbgfs_dir);
return -ENOMEM;
}
return 0;
}
-static void stmmac_exit_fs(void)
+static void stmmac_exit_fs(struct net_device *dev)
{
- debugfs_remove(stmmac_rings_status);
- debugfs_remove(stmmac_dma_cap);
- debugfs_remove(stmmac_fs_dir);
+ struct stmmac_priv *priv = netdev_priv(dev);
+
+ debugfs_remove_recursive(priv->dbgfs_dir);
}
#endif /* CONFIG_DEBUG_FS */
__setup("stmmaceth=", stmmac_cmdline_opt);
#endif /* MODULE */
+static int __init stmmac_init(void)
+{
+#ifdef CONFIG_DEBUG_FS
+ /* Create debugfs main directory if it doesn't exist yet */
+ if (!stmmac_fs_dir) {
+ stmmac_fs_dir = debugfs_create_dir(STMMAC_RESOURCE_NAME, NULL);
+
+ if (!stmmac_fs_dir || IS_ERR(stmmac_fs_dir)) {
+ pr_err("ERROR %s, debugfs create directory failed\n",
+ STMMAC_RESOURCE_NAME);
+
+ return -ENOMEM;
+ }
+ }
+#endif
+
+ return 0;
+}
+
+static void __exit stmmac_exit(void)
+{
+#ifdef CONFIG_DEBUG_FS
+ debugfs_remove_recursive(stmmac_fs_dir);
+#endif
+}
+
+module_init(stmmac_init)
+module_exit(stmmac_exit)
+
MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet device driver");
MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
MODULE_LICENSE("GPL");
*******************************************************************************/
#include <linux/platform_device.h>
+#include <linux/module.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/of_net.h>
cur_p->app0 |= STS_CTRL_APP0_SOP;
cur_p->len = skb_headlen(skb);
- cur_p->phys = dma_map_single(ndev->dev.parent, skb->data, skb->len,
- DMA_TO_DEVICE);
+ cur_p->phys = dma_map_single(ndev->dev.parent, skb->data,
+ skb_headlen(skb), DMA_TO_DEVICE);
cur_p->app4 = (unsigned long)skb;
for (ii = 0; ii < num_frag; ii++) {
u16 q_idx = packet->q_idx;
u32 pktlen = packet->total_data_buflen, msd_len = 0;
unsigned int section_index = NETVSC_INVALID_INDEX;
- struct sk_buff *skb = NULL;
unsigned long flag;
struct multi_send_data *msdp;
struct hv_netvsc_packet *msd_send = NULL, *cur_send = NULL;
if (cur_send)
ret = netvsc_send_pkt(cur_send, net_device);
- if (ret != 0) {
- if (section_index != NETVSC_INVALID_INDEX)
- netvsc_free_send_slot(net_device, section_index);
- } else if (skb) {
- dev_kfree_skb_any(skb);
- }
+ if (ret != 0 && section_index != NETVSC_INVALID_INDEX)
+ netvsc_free_send_slot(net_device, section_index);
return ret;
}
struct ieee802154_hw *hw;
struct at86rf2xx_chip_data *data;
struct regmap *regmap;
+ int slp_tr;
struct completion state_complete;
struct at86rf230_state_change state;
unsigned long cal_timeout;
s8 max_frame_retries;
bool is_tx;
+ bool is_tx_from_off;
u8 tx_retry;
struct sk_buff *tx_skb;
struct at86rf230_state_change tx;
};
-#define RG_TRX_STATUS (0x01)
-#define SR_TRX_STATUS 0x01, 0x1f, 0
-#define SR_RESERVED_01_3 0x01, 0x20, 5
-#define SR_CCA_STATUS 0x01, 0x40, 6
-#define SR_CCA_DONE 0x01, 0x80, 7
-#define RG_TRX_STATE (0x02)
-#define SR_TRX_CMD 0x02, 0x1f, 0
-#define SR_TRAC_STATUS 0x02, 0xe0, 5
-#define RG_TRX_CTRL_0 (0x03)
-#define SR_CLKM_CTRL 0x03, 0x07, 0
-#define SR_CLKM_SHA_SEL 0x03, 0x08, 3
-#define SR_PAD_IO_CLKM 0x03, 0x30, 4
-#define SR_PAD_IO 0x03, 0xc0, 6
-#define RG_TRX_CTRL_1 (0x04)
-#define SR_IRQ_POLARITY 0x04, 0x01, 0
-#define SR_IRQ_MASK_MODE 0x04, 0x02, 1
-#define SR_SPI_CMD_MODE 0x04, 0x0c, 2
-#define SR_RX_BL_CTRL 0x04, 0x10, 4
-#define SR_TX_AUTO_CRC_ON 0x04, 0x20, 5
-#define SR_IRQ_2_EXT_EN 0x04, 0x40, 6
-#define SR_PA_EXT_EN 0x04, 0x80, 7
-#define RG_PHY_TX_PWR (0x05)
-#define SR_TX_PWR 0x05, 0x0f, 0
-#define SR_PA_LT 0x05, 0x30, 4
-#define SR_PA_BUF_LT 0x05, 0xc0, 6
-#define RG_PHY_RSSI (0x06)
-#define SR_RSSI 0x06, 0x1f, 0
-#define SR_RND_VALUE 0x06, 0x60, 5
-#define SR_RX_CRC_VALID 0x06, 0x80, 7
-#define RG_PHY_ED_LEVEL (0x07)
-#define SR_ED_LEVEL 0x07, 0xff, 0
-#define RG_PHY_CC_CCA (0x08)
-#define SR_CHANNEL 0x08, 0x1f, 0
-#define SR_CCA_MODE 0x08, 0x60, 5
-#define SR_CCA_REQUEST 0x08, 0x80, 7
-#define RG_CCA_THRES (0x09)
-#define SR_CCA_ED_THRES 0x09, 0x0f, 0
-#define SR_RESERVED_09_1 0x09, 0xf0, 4
-#define RG_RX_CTRL (0x0a)
-#define SR_PDT_THRES 0x0a, 0x0f, 0
-#define SR_RESERVED_0a_1 0x0a, 0xf0, 4
-#define RG_SFD_VALUE (0x0b)
-#define SR_SFD_VALUE 0x0b, 0xff, 0
-#define RG_TRX_CTRL_2 (0x0c)
-#define SR_OQPSK_DATA_RATE 0x0c, 0x03, 0
-#define SR_SUB_MODE 0x0c, 0x04, 2
-#define SR_BPSK_QPSK 0x0c, 0x08, 3
-#define SR_OQPSK_SUB1_RC_EN 0x0c, 0x10, 4
-#define SR_RESERVED_0c_5 0x0c, 0x60, 5
-#define SR_RX_SAFE_MODE 0x0c, 0x80, 7
-#define RG_ANT_DIV (0x0d)
-#define SR_ANT_CTRL 0x0d, 0x03, 0
-#define SR_ANT_EXT_SW_EN 0x0d, 0x04, 2
-#define SR_ANT_DIV_EN 0x0d, 0x08, 3
-#define SR_RESERVED_0d_2 0x0d, 0x70, 4
-#define SR_ANT_SEL 0x0d, 0x80, 7
-#define RG_IRQ_MASK (0x0e)
-#define SR_IRQ_MASK 0x0e, 0xff, 0
-#define RG_IRQ_STATUS (0x0f)
-#define SR_IRQ_0_PLL_LOCK 0x0f, 0x01, 0
-#define SR_IRQ_1_PLL_UNLOCK 0x0f, 0x02, 1
-#define SR_IRQ_2_RX_START 0x0f, 0x04, 2
-#define SR_IRQ_3_TRX_END 0x0f, 0x08, 3
-#define SR_IRQ_4_CCA_ED_DONE 0x0f, 0x10, 4
-#define SR_IRQ_5_AMI 0x0f, 0x20, 5
-#define SR_IRQ_6_TRX_UR 0x0f, 0x40, 6
-#define SR_IRQ_7_BAT_LOW 0x0f, 0x80, 7
-#define RG_VREG_CTRL (0x10)
-#define SR_RESERVED_10_6 0x10, 0x03, 0
-#define SR_DVDD_OK 0x10, 0x04, 2
-#define SR_DVREG_EXT 0x10, 0x08, 3
-#define SR_RESERVED_10_3 0x10, 0x30, 4
-#define SR_AVDD_OK 0x10, 0x40, 6
-#define SR_AVREG_EXT 0x10, 0x80, 7
-#define RG_BATMON (0x11)
-#define SR_BATMON_VTH 0x11, 0x0f, 0
-#define SR_BATMON_HR 0x11, 0x10, 4
-#define SR_BATMON_OK 0x11, 0x20, 5
-#define SR_RESERVED_11_1 0x11, 0xc0, 6
-#define RG_XOSC_CTRL (0x12)
-#define SR_XTAL_TRIM 0x12, 0x0f, 0
-#define SR_XTAL_MODE 0x12, 0xf0, 4
-#define RG_RX_SYN (0x15)
-#define SR_RX_PDT_LEVEL 0x15, 0x0f, 0
-#define SR_RESERVED_15_2 0x15, 0x70, 4
-#define SR_RX_PDT_DIS 0x15, 0x80, 7
-#define RG_XAH_CTRL_1 (0x17)
-#define SR_RESERVED_17_8 0x17, 0x01, 0
-#define SR_AACK_PROM_MODE 0x17, 0x02, 1
-#define SR_AACK_ACK_TIME 0x17, 0x04, 2
-#define SR_RESERVED_17_5 0x17, 0x08, 3
-#define SR_AACK_UPLD_RES_FT 0x17, 0x10, 4
-#define SR_AACK_FLTR_RES_FT 0x17, 0x20, 5
-#define SR_CSMA_LBT_MODE 0x17, 0x40, 6
-#define SR_RESERVED_17_1 0x17, 0x80, 7
-#define RG_FTN_CTRL (0x18)
-#define SR_RESERVED_18_2 0x18, 0x7f, 0
-#define SR_FTN_START 0x18, 0x80, 7
-#define RG_PLL_CF (0x1a)
-#define SR_RESERVED_1a_2 0x1a, 0x7f, 0
-#define SR_PLL_CF_START 0x1a, 0x80, 7
-#define RG_PLL_DCU (0x1b)
-#define SR_RESERVED_1b_3 0x1b, 0x3f, 0
-#define SR_RESERVED_1b_2 0x1b, 0x40, 6
-#define SR_PLL_DCU_START 0x1b, 0x80, 7
-#define RG_PART_NUM (0x1c)
-#define SR_PART_NUM 0x1c, 0xff, 0
-#define RG_VERSION_NUM (0x1d)
-#define SR_VERSION_NUM 0x1d, 0xff, 0
-#define RG_MAN_ID_0 (0x1e)
-#define SR_MAN_ID_0 0x1e, 0xff, 0
-#define RG_MAN_ID_1 (0x1f)
-#define SR_MAN_ID_1 0x1f, 0xff, 0
-#define RG_SHORT_ADDR_0 (0x20)
-#define SR_SHORT_ADDR_0 0x20, 0xff, 0
-#define RG_SHORT_ADDR_1 (0x21)
-#define SR_SHORT_ADDR_1 0x21, 0xff, 0
-#define RG_PAN_ID_0 (0x22)
-#define SR_PAN_ID_0 0x22, 0xff, 0
-#define RG_PAN_ID_1 (0x23)
-#define SR_PAN_ID_1 0x23, 0xff, 0
-#define RG_IEEE_ADDR_0 (0x24)
-#define SR_IEEE_ADDR_0 0x24, 0xff, 0
-#define RG_IEEE_ADDR_1 (0x25)
-#define SR_IEEE_ADDR_1 0x25, 0xff, 0
-#define RG_IEEE_ADDR_2 (0x26)
-#define SR_IEEE_ADDR_2 0x26, 0xff, 0
-#define RG_IEEE_ADDR_3 (0x27)
-#define SR_IEEE_ADDR_3 0x27, 0xff, 0
-#define RG_IEEE_ADDR_4 (0x28)
-#define SR_IEEE_ADDR_4 0x28, 0xff, 0
-#define RG_IEEE_ADDR_5 (0x29)
-#define SR_IEEE_ADDR_5 0x29, 0xff, 0
-#define RG_IEEE_ADDR_6 (0x2a)
-#define SR_IEEE_ADDR_6 0x2a, 0xff, 0
-#define RG_IEEE_ADDR_7 (0x2b)
-#define SR_IEEE_ADDR_7 0x2b, 0xff, 0
-#define RG_XAH_CTRL_0 (0x2c)
-#define SR_SLOTTED_OPERATION 0x2c, 0x01, 0
-#define SR_MAX_CSMA_RETRIES 0x2c, 0x0e, 1
-#define SR_MAX_FRAME_RETRIES 0x2c, 0xf0, 4
-#define RG_CSMA_SEED_0 (0x2d)
-#define SR_CSMA_SEED_0 0x2d, 0xff, 0
-#define RG_CSMA_SEED_1 (0x2e)
-#define SR_CSMA_SEED_1 0x2e, 0x07, 0
-#define SR_AACK_I_AM_COORD 0x2e, 0x08, 3
-#define SR_AACK_DIS_ACK 0x2e, 0x10, 4
-#define SR_AACK_SET_PD 0x2e, 0x20, 5
-#define SR_AACK_FVN_MODE 0x2e, 0xc0, 6
-#define RG_CSMA_BE (0x2f)
-#define SR_MIN_BE 0x2f, 0x0f, 0
-#define SR_MAX_BE 0x2f, 0xf0, 4
+#define RG_TRX_STATUS (0x01)
+#define SR_TRX_STATUS 0x01, 0x1f, 0
+#define SR_RESERVED_01_3 0x01, 0x20, 5
+#define SR_CCA_STATUS 0x01, 0x40, 6
+#define SR_CCA_DONE 0x01, 0x80, 7
+#define RG_TRX_STATE (0x02)
+#define SR_TRX_CMD 0x02, 0x1f, 0
+#define SR_TRAC_STATUS 0x02, 0xe0, 5
+#define RG_TRX_CTRL_0 (0x03)
+#define SR_CLKM_CTRL 0x03, 0x07, 0
+#define SR_CLKM_SHA_SEL 0x03, 0x08, 3
+#define SR_PAD_IO_CLKM 0x03, 0x30, 4
+#define SR_PAD_IO 0x03, 0xc0, 6
+#define RG_TRX_CTRL_1 (0x04)
+#define SR_IRQ_POLARITY 0x04, 0x01, 0
+#define SR_IRQ_MASK_MODE 0x04, 0x02, 1
+#define SR_SPI_CMD_MODE 0x04, 0x0c, 2
+#define SR_RX_BL_CTRL 0x04, 0x10, 4
+#define SR_TX_AUTO_CRC_ON 0x04, 0x20, 5
+#define SR_IRQ_2_EXT_EN 0x04, 0x40, 6
+#define SR_PA_EXT_EN 0x04, 0x80, 7
+#define RG_PHY_TX_PWR (0x05)
+#define SR_TX_PWR 0x05, 0x0f, 0
+#define SR_PA_LT 0x05, 0x30, 4
+#define SR_PA_BUF_LT 0x05, 0xc0, 6
+#define RG_PHY_RSSI (0x06)
+#define SR_RSSI 0x06, 0x1f, 0
+#define SR_RND_VALUE 0x06, 0x60, 5
+#define SR_RX_CRC_VALID 0x06, 0x80, 7
+#define RG_PHY_ED_LEVEL (0x07)
+#define SR_ED_LEVEL 0x07, 0xff, 0
+#define RG_PHY_CC_CCA (0x08)
+#define SR_CHANNEL 0x08, 0x1f, 0
+#define SR_CCA_MODE 0x08, 0x60, 5
+#define SR_CCA_REQUEST 0x08, 0x80, 7
+#define RG_CCA_THRES (0x09)
+#define SR_CCA_ED_THRES 0x09, 0x0f, 0
+#define SR_RESERVED_09_1 0x09, 0xf0, 4
+#define RG_RX_CTRL (0x0a)
+#define SR_PDT_THRES 0x0a, 0x0f, 0
+#define SR_RESERVED_0a_1 0x0a, 0xf0, 4
+#define RG_SFD_VALUE (0x0b)
+#define SR_SFD_VALUE 0x0b, 0xff, 0
+#define RG_TRX_CTRL_2 (0x0c)
+#define SR_OQPSK_DATA_RATE 0x0c, 0x03, 0
+#define SR_SUB_MODE 0x0c, 0x04, 2
+#define SR_BPSK_QPSK 0x0c, 0x08, 3
+#define SR_OQPSK_SUB1_RC_EN 0x0c, 0x10, 4
+#define SR_RESERVED_0c_5 0x0c, 0x60, 5
+#define SR_RX_SAFE_MODE 0x0c, 0x80, 7
+#define RG_ANT_DIV (0x0d)
+#define SR_ANT_CTRL 0x0d, 0x03, 0
+#define SR_ANT_EXT_SW_EN 0x0d, 0x04, 2
+#define SR_ANT_DIV_EN 0x0d, 0x08, 3
+#define SR_RESERVED_0d_2 0x0d, 0x70, 4
+#define SR_ANT_SEL 0x0d, 0x80, 7
+#define RG_IRQ_MASK (0x0e)
+#define SR_IRQ_MASK 0x0e, 0xff, 0
+#define RG_IRQ_STATUS (0x0f)
+#define SR_IRQ_0_PLL_LOCK 0x0f, 0x01, 0
+#define SR_IRQ_1_PLL_UNLOCK 0x0f, 0x02, 1
+#define SR_IRQ_2_RX_START 0x0f, 0x04, 2
+#define SR_IRQ_3_TRX_END 0x0f, 0x08, 3
+#define SR_IRQ_4_CCA_ED_DONE 0x0f, 0x10, 4
+#define SR_IRQ_5_AMI 0x0f, 0x20, 5
+#define SR_IRQ_6_TRX_UR 0x0f, 0x40, 6
+#define SR_IRQ_7_BAT_LOW 0x0f, 0x80, 7
+#define RG_VREG_CTRL (0x10)
+#define SR_RESERVED_10_6 0x10, 0x03, 0
+#define SR_DVDD_OK 0x10, 0x04, 2
+#define SR_DVREG_EXT 0x10, 0x08, 3
+#define SR_RESERVED_10_3 0x10, 0x30, 4
+#define SR_AVDD_OK 0x10, 0x40, 6
+#define SR_AVREG_EXT 0x10, 0x80, 7
+#define RG_BATMON (0x11)
+#define SR_BATMON_VTH 0x11, 0x0f, 0
+#define SR_BATMON_HR 0x11, 0x10, 4
+#define SR_BATMON_OK 0x11, 0x20, 5
+#define SR_RESERVED_11_1 0x11, 0xc0, 6
+#define RG_XOSC_CTRL (0x12)
+#define SR_XTAL_TRIM 0x12, 0x0f, 0
+#define SR_XTAL_MODE 0x12, 0xf0, 4
+#define RG_RX_SYN (0x15)
+#define SR_RX_PDT_LEVEL 0x15, 0x0f, 0
+#define SR_RESERVED_15_2 0x15, 0x70, 4
+#define SR_RX_PDT_DIS 0x15, 0x80, 7
+#define RG_XAH_CTRL_1 (0x17)
+#define SR_RESERVED_17_8 0x17, 0x01, 0
+#define SR_AACK_PROM_MODE 0x17, 0x02, 1
+#define SR_AACK_ACK_TIME 0x17, 0x04, 2
+#define SR_RESERVED_17_5 0x17, 0x08, 3
+#define SR_AACK_UPLD_RES_FT 0x17, 0x10, 4
+#define SR_AACK_FLTR_RES_FT 0x17, 0x20, 5
+#define SR_CSMA_LBT_MODE 0x17, 0x40, 6
+#define SR_RESERVED_17_1 0x17, 0x80, 7
+#define RG_FTN_CTRL (0x18)
+#define SR_RESERVED_18_2 0x18, 0x7f, 0
+#define SR_FTN_START 0x18, 0x80, 7
+#define RG_PLL_CF (0x1a)
+#define SR_RESERVED_1a_2 0x1a, 0x7f, 0
+#define SR_PLL_CF_START 0x1a, 0x80, 7
+#define RG_PLL_DCU (0x1b)
+#define SR_RESERVED_1b_3 0x1b, 0x3f, 0
+#define SR_RESERVED_1b_2 0x1b, 0x40, 6
+#define SR_PLL_DCU_START 0x1b, 0x80, 7
+#define RG_PART_NUM (0x1c)
+#define SR_PART_NUM 0x1c, 0xff, 0
+#define RG_VERSION_NUM (0x1d)
+#define SR_VERSION_NUM 0x1d, 0xff, 0
+#define RG_MAN_ID_0 (0x1e)
+#define SR_MAN_ID_0 0x1e, 0xff, 0
+#define RG_MAN_ID_1 (0x1f)
+#define SR_MAN_ID_1 0x1f, 0xff, 0
+#define RG_SHORT_ADDR_0 (0x20)
+#define SR_SHORT_ADDR_0 0x20, 0xff, 0
+#define RG_SHORT_ADDR_1 (0x21)
+#define SR_SHORT_ADDR_1 0x21, 0xff, 0
+#define RG_PAN_ID_0 (0x22)
+#define SR_PAN_ID_0 0x22, 0xff, 0
+#define RG_PAN_ID_1 (0x23)
+#define SR_PAN_ID_1 0x23, 0xff, 0
+#define RG_IEEE_ADDR_0 (0x24)
+#define SR_IEEE_ADDR_0 0x24, 0xff, 0
+#define RG_IEEE_ADDR_1 (0x25)
+#define SR_IEEE_ADDR_1 0x25, 0xff, 0
+#define RG_IEEE_ADDR_2 (0x26)
+#define SR_IEEE_ADDR_2 0x26, 0xff, 0
+#define RG_IEEE_ADDR_3 (0x27)
+#define SR_IEEE_ADDR_3 0x27, 0xff, 0
+#define RG_IEEE_ADDR_4 (0x28)
+#define SR_IEEE_ADDR_4 0x28, 0xff, 0
+#define RG_IEEE_ADDR_5 (0x29)
+#define SR_IEEE_ADDR_5 0x29, 0xff, 0
+#define RG_IEEE_ADDR_6 (0x2a)
+#define SR_IEEE_ADDR_6 0x2a, 0xff, 0
+#define RG_IEEE_ADDR_7 (0x2b)
+#define SR_IEEE_ADDR_7 0x2b, 0xff, 0
+#define RG_XAH_CTRL_0 (0x2c)
+#define SR_SLOTTED_OPERATION 0x2c, 0x01, 0
+#define SR_MAX_CSMA_RETRIES 0x2c, 0x0e, 1
+#define SR_MAX_FRAME_RETRIES 0x2c, 0xf0, 4
+#define RG_CSMA_SEED_0 (0x2d)
+#define SR_CSMA_SEED_0 0x2d, 0xff, 0
+#define RG_CSMA_SEED_1 (0x2e)
+#define SR_CSMA_SEED_1 0x2e, 0x07, 0
+#define SR_AACK_I_AM_COORD 0x2e, 0x08, 3
+#define SR_AACK_DIS_ACK 0x2e, 0x10, 4
+#define SR_AACK_SET_PD 0x2e, 0x20, 5
+#define SR_AACK_FVN_MODE 0x2e, 0xc0, 6
+#define RG_CSMA_BE (0x2f)
+#define SR_MIN_BE 0x2f, 0x0f, 0
+#define SR_MAX_BE 0x2f, 0xf0, 4
#define CMD_REG 0x80
#define CMD_REG_MASK 0x3f
#define STATE_BUSY_RX_AACK_NOCLK 0x1E
#define STATE_TRANSITION_IN_PROGRESS 0x1F
+#define TRX_STATE_MASK (0x1F)
+
#define AT86RF2XX_NUMREGS 0x3F
static void
return regmap_update_bits(lp->regmap, addr, mask, data << shift);
}
+static inline void
+at86rf230_slp_tr_rising_edge(struct at86rf230_local *lp)
+{
+ gpio_set_value(lp->slp_tr, 1);
+ udelay(1);
+ gpio_set_value(lp->slp_tr, 0);
+}
+
static bool
at86rf230_reg_writeable(struct device *dev, unsigned int reg)
{
struct at86rf230_state_change *ctx = context;
struct at86rf230_local *lp = ctx->lp;
const u8 *buf = ctx->buf;
- const u8 trx_state = buf[1] & 0x1f;
+ const u8 trx_state = buf[1] & TRX_STATE_MASK;
/* Assert state change */
if (trx_state != ctx->to_state) {
switch (ctx->to_state) {
case STATE_RX_AACK_ON:
tim = ktime_set(0, c->t_off_to_aack * NSEC_PER_USEC);
+ /* state change from TRX_OFF to RX_AACK_ON to do a
+ * calibration, we need to reset the timeout for the
+ * next one.
+ */
+ lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
goto change;
+ case STATE_TX_ARET_ON:
case STATE_TX_ON:
tim = ktime_set(0, c->t_off_to_tx_on * NSEC_PER_USEC);
- /* state change from TRX_OFF to TX_ON to do a
- * calibration, we need to reset the timeout for the
+ /* state change from TRX_OFF to TX_ON or ARET_ON to do
+ * a calibration, we need to reset the timeout for the
* next one.
*/
lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
struct at86rf230_state_change *ctx = context;
struct at86rf230_local *lp = ctx->lp;
u8 *buf = ctx->buf;
- const u8 trx_state = buf[1] & 0x1f;
+ const u8 trx_state = buf[1] & TRX_STATE_MASK;
int rc;
/* Check for "possible" STATE_TRANSITION_IN_PROGRESS */
at86rf230_tx_complete, true);
}
-static void
-at86rf230_tx_trac_error(void *context)
-{
- struct at86rf230_state_change *ctx = context;
- struct at86rf230_local *lp = ctx->lp;
-
- at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
- at86rf230_tx_on, true);
-}
-
static void
at86rf230_tx_trac_check(void *context)
{
const u8 trac = (buf[1] & 0xe0) >> 5;
/* If trac status is different than zero we need to do a state change
- * to STATE_FORCE_TRX_OFF then STATE_TX_ON to recover the transceiver
- * state to TX_ON.
+ * to STATE_FORCE_TRX_OFF then STATE_RX_AACK_ON to recover the
+ * transceiver.
*/
if (trac)
at86rf230_async_state_change(lp, ctx, STATE_FORCE_TRX_OFF,
- at86rf230_tx_trac_error, true);
+ at86rf230_tx_on, true);
else
at86rf230_tx_on(context);
}
u8 *buf = ctx->buf;
int rc;
- buf[0] = (RG_TRX_STATE & CMD_REG_MASK) | CMD_REG | CMD_WRITE;
- buf[1] = STATE_BUSY_TX;
ctx->trx.len = 2;
- ctx->msg.complete = NULL;
- rc = spi_async(lp->spi, &ctx->msg);
- if (rc)
- at86rf230_async_error(lp, ctx, rc);
+
+ if (gpio_is_valid(lp->slp_tr)) {
+ at86rf230_slp_tr_rising_edge(lp);
+ } else {
+ buf[0] = (RG_TRX_STATE & CMD_REG_MASK) | CMD_REG | CMD_WRITE;
+ buf[1] = STATE_BUSY_TX;
+ ctx->msg.complete = NULL;
+ rc = spi_async(lp->spi, &ctx->msg);
+ if (rc)
+ at86rf230_async_error(lp, ctx, rc);
+ }
}
static void
* are in STATE_TX_ON. The pfad differs here, so we change
* the complete handler.
*/
- if (lp->tx_aret)
- at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
- at86rf230_xmit_tx_on, false);
- else
+ if (lp->tx_aret) {
+ if (lp->is_tx_from_off) {
+ lp->is_tx_from_off = false;
+ at86rf230_async_state_change(lp, ctx, STATE_TX_ARET_ON,
+ at86rf230_xmit_tx_on,
+ false);
+ } else {
+ at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
+ at86rf230_xmit_tx_on,
+ false);
+ }
+ } else {
at86rf230_async_state_change(lp, ctx, STATE_TX_ON,
at86rf230_write_frame, false);
+ }
}
static int
* to TX_ON, the lp->cal_timeout should be reinit by state_delay
* function then to start in the next 5 minutes.
*/
- if (time_is_before_jiffies(lp->cal_timeout))
+ if (time_is_before_jiffies(lp->cal_timeout)) {
+ lp->is_tx_from_off = true;
at86rf230_async_state_change(lp, ctx, STATE_TRX_OFF,
at86rf230_xmit_start, false);
- else
+ } else {
at86rf230_xmit_start(ctx);
+ }
return 0;
}
static int
at86rf230_start(struct ieee802154_hw *hw)
{
- struct at86rf230_local *lp = hw->priv;
-
- lp->cal_timeout = jiffies + AT86RF2XX_CAL_LOOP_TIMEOUT;
return at86rf230_sync_state_change(hw->priv, STATE_RX_AACK_ON);
}
lp = hw->priv;
lp->hw = hw;
lp->spi = spi;
+ lp->slp_tr = slp_tr;
hw->parent = &spi->dev;
hw->vif_data_size = sizeof(*lp);
ieee802154_random_extended_addr(&hw->phy->perm_extended_addr);
goto del_unicast;
}
+ if (dev->flags & IFF_PROMISC) {
+ err = dev_set_promiscuity(lowerdev, 1);
+ if (err < 0)
+ goto clear_multi;
+ }
+
hash_add:
macvlan_hash_add(vlan);
return 0;
+clear_multi:
+ dev_set_allmulti(lowerdev, -1);
del_unicast:
dev_uc_del(lowerdev, dev->dev_addr);
out:
if (dev->flags & IFF_ALLMULTI)
dev_set_allmulti(lowerdev, -1);
+ if (dev->flags & IFF_PROMISC)
+ dev_set_promiscuity(lowerdev, -1);
+
dev_uc_del(lowerdev, dev->dev_addr);
hash_del:
if (dev->flags & IFF_UP) {
if (change & IFF_ALLMULTI)
dev_set_allmulti(lowerdev, dev->flags & IFF_ALLMULTI ? 1 : -1);
+ if (change & IFF_PROMISC)
+ dev_set_promiscuity(lowerdev,
+ dev->flags & IFF_PROMISC ? 1 : -1);
+
}
}
config AMD_XGBE_PHY
tristate "Driver for the AMD 10GbE (amd-xgbe) PHYs"
depends on (OF || ACPI) && HAS_IOMEM
+ depends on ARM64 || COMPILE_TEST
---help---
Currently supports the AMD 10GbE PHY
return ret;
}
+static bool amd_xgbe_phy_use_xgmii_mode(struct phy_device *phydev)
+{
+ if (phydev->autoneg == AUTONEG_ENABLE) {
+ if (phydev->advertising & ADVERTISED_10000baseKR_Full)
+ return true;
+ } else {
+ if (phydev->speed == SPEED_10000)
+ return true;
+ }
+
+ return false;
+}
+
+static bool amd_xgbe_phy_use_gmii_2500_mode(struct phy_device *phydev)
+{
+ if (phydev->autoneg == AUTONEG_ENABLE) {
+ if (phydev->advertising & ADVERTISED_2500baseX_Full)
+ return true;
+ } else {
+ if (phydev->speed == SPEED_2500)
+ return true;
+ }
+
+ return false;
+}
+
+static bool amd_xgbe_phy_use_gmii_mode(struct phy_device *phydev)
+{
+ if (phydev->autoneg == AUTONEG_ENABLE) {
+ if (phydev->advertising & ADVERTISED_1000baseKX_Full)
+ return true;
+ } else {
+ if (phydev->speed == SPEED_1000)
+ return true;
+ }
+
+ return false;
+}
+
static int amd_xgbe_phy_set_an(struct phy_device *phydev, bool enable,
bool restart)
{
/* Set initial mode - call the mode setting routines
* directly to insure we are properly configured
*/
- if (phydev->advertising & SUPPORTED_10000baseKR_Full)
+ if (amd_xgbe_phy_use_xgmii_mode(phydev))
ret = amd_xgbe_phy_xgmii_mode(phydev);
- else if (phydev->advertising & SUPPORTED_1000baseKX_Full)
+ else if (amd_xgbe_phy_use_gmii_mode(phydev))
ret = amd_xgbe_phy_gmii_mode(phydev);
- else if (phydev->advertising & SUPPORTED_2500baseX_Full)
+ else if (amd_xgbe_phy_use_gmii_2500_mode(phydev))
ret = amd_xgbe_phy_gmii_2500_mode(phydev);
else
ret = -EINVAL;
.name = "Broadcom BCM7425",
.features = PHY_GBIT_FEATURES |
SUPPORTED_Pause | SUPPORTED_Asym_Pause,
- .flags = 0,
+ .flags = PHY_IS_INTERNAL,
.config_init = bcm7xxx_config_init,
.config_aneg = genphy_config_aneg,
.read_status = genphy_read_status,
#define PSF_TX 0x1000
#define EXT_EVENT 1
#define CAL_EVENT 7
-#define CAL_TRIGGER 7
+#define CAL_TRIGGER 1
#define DP83640_N_PINS 12
#define MII_DP83640_MICR 0x11
else
evnt |= EVNT_RISE;
}
+ mutex_lock(&clock->extreg_lock);
ext_write(0, phydev, PAGE5, PTP_EVNT, evnt);
+ mutex_unlock(&clock->extreg_lock);
return 0;
case PTP_CLK_REQ_PEROUT:
static void enable_status_frames(struct phy_device *phydev, bool on)
{
+ struct dp83640_private *dp83640 = phydev->priv;
+ struct dp83640_clock *clock = dp83640->clock;
u16 cfg0 = 0, ver;
if (on)
ver = (PSF_PTPVER & VERSIONPTP_MASK) << VERSIONPTP_SHIFT;
+ mutex_lock(&clock->extreg_lock);
+
ext_write(0, phydev, PAGE5, PSF_CFG0, cfg0);
ext_write(0, phydev, PAGE6, PSF_CFG1, ver);
+ mutex_unlock(&clock->extreg_lock);
+
if (!phydev->attached_dev) {
pr_warn("expected to find an attached netdevice\n");
return;
list_del_init(&rxts->list);
phy2rxts(phy_rxts, rxts);
- spin_lock_irqsave(&dp83640->rx_queue.lock, flags);
+ spin_lock(&dp83640->rx_queue.lock);
skb_queue_walk(&dp83640->rx_queue, skb) {
struct dp83640_skb_info *skb_info;
break;
}
}
- spin_unlock_irqrestore(&dp83640->rx_queue.lock, flags);
+ spin_unlock(&dp83640->rx_queue.lock);
if (!shhwtstamps)
list_add_tail(&rxts->list, &dp83640->rxts);
if (clock->chosen && !list_empty(&clock->phylist))
recalibrate(clock);
- else
+ else {
+ mutex_lock(&clock->extreg_lock);
enable_broadcast(phydev, clock->page, 1);
+ mutex_unlock(&clock->extreg_lock);
+ }
enable_status_frames(phydev, true);
+
+ mutex_lock(&clock->extreg_lock);
ext_write(0, phydev, PAGE4, PTP_CTL, PTP_ENABLE);
+ mutex_unlock(&clock->extreg_lock);
+
return 0;
}
if (!new_bus->irq[i])
new_bus->irq[i] = PHY_POLL;
- snprintf(new_bus->id, MII_BUS_ID_SIZE, "gpio-%x", bus_id);
+ if (bus_id != -1)
+ snprintf(new_bus->id, MII_BUS_ID_SIZE, "gpio-%x", bus_id);
+ else
+ strncpy(new_bus->id, "gpio", MII_BUS_ID_SIZE);
if (devm_gpio_request(dev, bitbang->mdc, "mdc"))
goto out_free_bus;
}
clk = devm_clk_get(&phydev->dev, "rmii-ref");
- if (!IS_ERR(clk)) {
+ /* NOTE: clk may be NULL if building without CONFIG_HAVE_CLK */
+ if (!IS_ERR_OR_NULL(clk)) {
unsigned long rate = clk_get_rate(clk);
bool rmii_ref_clk_sel_25_mhz;
*/
void phy_start(struct phy_device *phydev)
{
+ bool do_resume = false;
+ int err = 0;
+
mutex_lock(&phydev->lock);
switch (phydev->state) {
phydev->state = PHY_UP;
break;
case PHY_HALTED:
+ /* make sure interrupts are re-enabled for the PHY */
+ err = phy_enable_interrupts(phydev);
+ if (err < 0)
+ break;
+
phydev->state = PHY_RESUMING;
+ do_resume = true;
+ break;
default:
break;
}
mutex_unlock(&phydev->lock);
+
+ /* if phy was suspended, bring the physical link up again */
+ if (do_resume)
+ phy_resume(phydev);
}
EXPORT_SYMBOL(phy_start);
struct delayed_work *dwork = to_delayed_work(work);
struct phy_device *phydev =
container_of(dwork, struct phy_device, state_queue);
- bool needs_aneg = false, do_suspend = false, do_resume = false;
+ bool needs_aneg = false, do_suspend = false;
int err = 0;
mutex_lock(&phydev->lock);
}
break;
case PHY_RESUMING:
- err = phy_clear_interrupt(phydev);
- if (err)
- break;
-
- err = phy_config_interrupt(phydev, PHY_INTERRUPT_ENABLED);
- if (err)
- break;
-
if (AUTONEG_ENABLE == phydev->autoneg) {
err = phy_aneg_done(phydev);
if (err < 0)
}
phydev->adjust_link(phydev->attached_dev);
}
- do_resume = true;
break;
}
err = phy_start_aneg(phydev);
else if (do_suspend)
phy_suspend(phydev);
- else if (do_resume)
- phy_resume(phydev);
if (err < 0)
phy_error(phydev);
{
/* According to 802.3az,the EEE is supported only in full duplex-mode.
* Also EEE feature is active when core is operating with MII, GMII
- * or RGMII. Internal PHYs are also allowed to proceed and should
- * return an error if they do not support EEE.
+ * or RGMII (all kinds). Internal PHYs are also allowed to proceed and
+ * should return an error if they do not support EEE.
*/
if ((phydev->duplex == DUPLEX_FULL) &&
((phydev->interface == PHY_INTERFACE_MODE_MII) ||
(phydev->interface == PHY_INTERFACE_MODE_GMII) ||
- (phydev->interface == PHY_INTERFACE_MODE_RGMII) ||
+ (phydev->interface >= PHY_INTERFACE_MODE_RGMII &&
+ phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID) ||
phy_is_internal(phydev))) {
int eee_lp, eee_cap, eee_adv;
u32 lp, cap, adv;
struct sock *sk = sk_pppox(po);
lock_sock(sk);
+ if (po->pppoe_dev) {
+ dev_put(po->pppoe_dev);
+ po->pppoe_dev = NULL;
+ }
pppox_unbind_sock(sk);
release_sock(sk);
sock_put(sk);
* payload data instead.
*/
usbnet_set_skb_tx_stats(skb_out, n,
- ctx->tx_curr_frame_payload - skb_out->len);
+ (long)ctx->tx_curr_frame_payload - skb_out->len);
return skb_out;
{REALTEK_USB_DEVICE(VENDOR_ID_REALTEK, 0x8153)},
{REALTEK_USB_DEVICE(VENDOR_ID_SAMSUNG, 0xa101)},
{REALTEK_USB_DEVICE(VENDOR_ID_LENOVO, 0x7205)},
+ {REALTEK_USB_DEVICE(VENDOR_ID_LENOVO, 0x304f)},
{}
};
struct net_device *net)
{
struct usbnet *dev = netdev_priv(net);
- int length;
+ unsigned int length;
struct urb *urb = NULL;
struct skb_data *entry;
struct driver_info *info = dev->driver_info;
}
} else
netif_dbg(dev, tx_queued, dev->net,
- "> tx, len %d, type 0x%x\n", length, skb->protocol);
+ "> tx, len %u, type 0x%x\n", length, skb->protocol);
#ifdef CONFIG_PM
deferred:
#endif
* to the list by the previous loop.
*/
if (!net_eq(dev_net(vxlan->dev), net))
- unregister_netdevice_queue(dev, &list);
+ unregister_netdevice_queue(vxlan->dev, &list);
}
unregister_netdevice_many(&list);
struct sk_buff *skb;
struct ath_frame_info *fi;
struct ieee80211_tx_info *info;
- struct ieee80211_vif *vif;
struct ath_hw *ah = sc->sc_ah;
if (sc->tx99_state || !ah->tpc_enabled)
return MAX_RATE_POWER;
skb = bf->bf_mpdu;
- info = IEEE80211_SKB_CB(skb);
- vif = info->control.vif;
-
- if (!vif) {
- max_power = sc->cur_chan->cur_txpower;
- goto out;
- }
-
- if (vif->bss_conf.txpower_type != NL80211_TX_POWER_LIMITED) {
- max_power = min_t(u8, sc->cur_chan->cur_txpower,
- 2 * vif->bss_conf.txpower);
- goto out;
- }
-
fi = get_frame_info(skb);
+ info = IEEE80211_SKB_CB(skb);
if (!AR_SREV_9300_20_OR_LATER(ah)) {
int txpower = fi->tx_power;
txpower -= 2;
txpower = max(txpower, 0);
- max_power = min_t(u8, ah->tx_power[rateidx],
- 2 * vif->bss_conf.txpower);
- max_power = min_t(u8, max_power, txpower);
+ max_power = min_t(u8, ah->tx_power[rateidx], txpower);
+
+ /* XXX: clamp minimum TX power at 1 for AR9160 since if
+ * max_power is set to 0, frames are transmitted at max
+ * TX power
+ */
+ if (!max_power && !AR_SREV_9280_20_OR_LATER(ah))
+ max_power = 1;
} else if (!bf->bf_state.bfs_paprd) {
if (rateidx < 8 && (info->flags & IEEE80211_TX_CTL_STBC))
max_power = min_t(u8, ah->tx_power_stbc[rateidx],
- 2 * vif->bss_conf.txpower);
+ fi->tx_power);
else
max_power = min_t(u8, ah->tx_power[rateidx],
- 2 * vif->bss_conf.txpower);
- max_power = min(max_power, fi->tx_power);
+ fi->tx_power);
} else {
max_power = ah->paprd_training_power;
}
-out:
- /* XXX: clamp minimum TX power at 1 for AR9160 since if max_power
- * is set to 0, frames are transmitted at max TX power
- */
- return (!max_power && !AR_SREV_9280_20_OR_LATER(ah)) ? 1 : max_power;
+
+ return max_power;
}
static void ath_buf_set_rate(struct ath_softc *sc, struct ath_buf *bf,
struct ath_node *an = NULL;
enum ath9k_key_type keytype;
bool short_preamble = false;
+ u8 txpower;
/*
* We check if Short Preamble is needed for the CTS rate by
if (sta)
an = (struct ath_node *) sta->drv_priv;
+ if (tx_info->control.vif) {
+ struct ieee80211_vif *vif = tx_info->control.vif;
+
+ txpower = 2 * vif->bss_conf.txpower;
+ } else {
+ struct ath_softc *sc = hw->priv;
+
+ txpower = sc->cur_chan->cur_txpower;
+ }
+
memset(fi, 0, sizeof(*fi));
fi->txq = -1;
if (hw_key)
fi->keyix = ATH9K_TXKEYIX_INVALID;
fi->keytype = keytype;
fi->framelen = framelen;
- fi->tx_power = MAX_RATE_POWER;
+ fi->tx_power = txpower;
if (!rate)
return;
Intel 7260 Wi-Fi Adapter
Intel 3160 Wi-Fi Adapter
Intel 7265 Wi-Fi Adapter
+ Intel 3165 Wi-Fi Adapter
This driver uses the kernel's mac80211 subsystem.
/* Highest firmware API version supported */
#define IWL7260_UCODE_API_MAX 13
-#define IWL3160_UCODE_API_MAX 13
/* Oldest version we won't warn about */
#define IWL7260_UCODE_API_OK 12
-#define IWL3160_UCODE_API_OK 12
+#define IWL3165_UCODE_API_OK 13
/* Lowest firmware API version supported */
#define IWL7260_UCODE_API_MIN 10
-#define IWL3160_UCODE_API_MIN 10
+#define IWL3165_UCODE_API_MIN 13
/* NVM versions */
#define IWL7260_NVM_VERSION 0x0a1d
#define IWL3160_FW_PRE "iwlwifi-3160-"
#define IWL3160_MODULE_FIRMWARE(api) IWL3160_FW_PRE __stringify(api) ".ucode"
-#define IWL3165_FW_PRE "iwlwifi-3165-"
-#define IWL3165_MODULE_FIRMWARE(api) IWL3165_FW_PRE __stringify(api) ".ucode"
-
#define IWL7265_FW_PRE "iwlwifi-7265-"
#define IWL7265_MODULE_FIRMWARE(api) IWL7265_FW_PRE __stringify(api) ".ucode"
const struct iwl_cfg iwl3165_2ac_cfg = {
.name = "Intel(R) Dual Band Wireless AC 3165",
- .fw_name_pre = IWL3165_FW_PRE,
+ .fw_name_pre = IWL7265D_FW_PRE,
IWL_DEVICE_7000,
+ /* sparse doens't like the re-assignment but it is safe */
+#ifndef __CHECKER__
+ .ucode_api_ok = IWL3165_UCODE_API_OK,
+ .ucode_api_min = IWL3165_UCODE_API_MIN,
+#endif
.ht_params = &iwl7000_ht_params,
.nvm_ver = IWL3165_NVM_VERSION,
.nvm_calib_ver = IWL3165_TX_POWER_VERSION,
MODULE_FIRMWARE(IWL7260_MODULE_FIRMWARE(IWL7260_UCODE_API_OK));
MODULE_FIRMWARE(IWL3160_MODULE_FIRMWARE(IWL3160_UCODE_API_OK));
-MODULE_FIRMWARE(IWL3165_MODULE_FIRMWARE(IWL3160_UCODE_API_OK));
MODULE_FIRMWARE(IWL7265_MODULE_FIRMWARE(IWL7260_UCODE_API_OK));
MODULE_FIRMWARE(IWL7265D_MODULE_FIRMWARE(IWL7260_UCODE_API_OK));
* GPL LICENSE SUMMARY
*
* Copyright(c) 2008 - 2014 Intel Corporation. All rights reserved.
+ * Copyright(c) 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* BSD LICENSE
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
+ * Copyright(c) 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
return;
}
+ if (data->sku_cap_mimo_disabled)
+ rx_chains = 1;
+
ht_info->ht_supported = true;
ht_info->cap = IEEE80211_HT_CAP_DSSSCCK40;
* GPL LICENSE SUMMARY
*
* Copyright(c) 2008 - 2014 Intel Corporation. All rights reserved.
+ * Copyright(c) 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* BSD LICENSE
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
+ * Copyright(c) 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
bool sku_cap_11ac_enable;
bool sku_cap_amt_enable;
bool sku_cap_ipan_enable;
+ bool sku_cap_mimo_disabled;
u16 radio_cfg_type;
u8 radio_cfg_step;
* longer than the passive one, which is essential for fragmented scan.
* @IWL_UCODE_TLV_API_WIFI_MCC_UPDATE: ucode supports MCC updates with source.
* IWL_UCODE_TLV_API_HDC_PHASE_0: ucode supports finer configuration of LTR
+ * @IWL_UCODE_TLV_API_TX_POWER_DEV: new API for tx power.
* @IWL_UCODE_TLV_API_BASIC_DWELL: use only basic dwell time in scan command,
* regardless of the band or the number of the probes. FW will calculate
* the actual dwell time.
IWL_UCODE_TLV_API_FRAGMENTED_SCAN = BIT(8),
IWL_UCODE_TLV_API_WIFI_MCC_UPDATE = BIT(9),
IWL_UCODE_TLV_API_HDC_PHASE_0 = BIT(10),
+ IWL_UCODE_TLV_API_TX_POWER_DEV = BIT(11),
IWL_UCODE_TLV_API_BASIC_DWELL = BIT(13),
IWL_UCODE_TLV_API_SCD_CFG = BIT(15),
IWL_UCODE_TLV_API_SINGLE_SCAN_EBS = BIT(16),
* GPL LICENSE SUMMARY
*
* Copyright(c) 2008 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* BSD LICENSE
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
/* SKU Capabilities (actual values from NVM definition) */
enum nvm_sku_bits {
- NVM_SKU_CAP_BAND_24GHZ = BIT(0),
- NVM_SKU_CAP_BAND_52GHZ = BIT(1),
- NVM_SKU_CAP_11N_ENABLE = BIT(2),
- NVM_SKU_CAP_11AC_ENABLE = BIT(3),
+ NVM_SKU_CAP_BAND_24GHZ = BIT(0),
+ NVM_SKU_CAP_BAND_52GHZ = BIT(1),
+ NVM_SKU_CAP_11N_ENABLE = BIT(2),
+ NVM_SKU_CAP_11AC_ENABLE = BIT(3),
+ NVM_SKU_CAP_MIMO_DISABLE = BIT(5),
};
/*
if (cfg->ht_params->ldpc)
vht_cap->cap |= IEEE80211_VHT_CAP_RXLDPC;
+ if (data->sku_cap_mimo_disabled) {
+ num_rx_ants = 1;
+ num_tx_ants = 1;
+ }
+
if (num_tx_ants > 1)
vht_cap->cap |= IEEE80211_VHT_CAP_TXSTBC;
else
const u8 *hw_addr;
if (mac_override) {
+ static const u8 reserved_mac[] = {
+ 0x02, 0xcc, 0xaa, 0xff, 0xee, 0x00
+ };
+
hw_addr = (const u8 *)(mac_override +
MAC_ADDRESS_OVERRIDE_FAMILY_8000);
data->hw_addr[4] = hw_addr[5];
data->hw_addr[5] = hw_addr[4];
- if (is_valid_ether_addr(data->hw_addr))
+ /*
+ * Force the use of the OTP MAC address in case of reserved MAC
+ * address in the NVM, or if address is given but invalid.
+ */
+ if (is_valid_ether_addr(data->hw_addr) &&
+ memcmp(reserved_mac, hw_addr, ETH_ALEN) != 0)
return;
IWL_ERR_DEV(dev,
data->sku_cap_11n_enable = false;
data->sku_cap_11ac_enable = data->sku_cap_11n_enable &&
(sku & NVM_SKU_CAP_11AC_ENABLE);
+ data->sku_cap_mimo_disabled = sku & NVM_SKU_CAP_MIMO_DISABLE;
data->n_hw_addrs = iwl_get_n_hw_addrs(cfg, nvm_sw);
* GPL LICENSE SUMMARY
*
* Copyright(c) 2007 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* BSD LICENSE
*
* Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
*
* All the handlers MUST be implemented
*
- * @start_hw: starts the HW- from that point on, the HW can send interrupts
- * May sleep
+ * @start_hw: starts the HW. If low_power is true, the NIC needs to be taken
+ * out of a low power state. From that point on, the HW can send
+ * interrupts. May sleep.
* @op_mode_leave: Turn off the HW RF kill indication if on
* May sleep
* @start_fw: allocates and inits all the resources for the transport
* the SCD base address in SRAM, then provide it here, or 0 otherwise.
* May sleep
* @stop_device: stops the whole device (embedded CPU put to reset) and stops
- * the HW. From that point on, the HW will be in low power but will still
- * issue interrupt if the HW RF kill is triggered. This callback must do
- * the right thing and not crash even if start_hw() was called but not
- * start_fw(). May sleep
+ * the HW. If low_power is true, the NIC will be put in low power state.
+ * From that point on, the HW will be stopped but will still issue an
+ * interrupt if the HW RF kill switch is triggered.
+ * This callback must do the right thing and not crash even if %start_hw()
+ * was called but not &start_fw(). May sleep.
* @d3_suspend: put the device into the correct mode for WoWLAN during
* suspend. This is optional, if not implemented WoWLAN will not be
* supported. This callback may sleep.
*/
struct iwl_trans_ops {
- int (*start_hw)(struct iwl_trans *iwl_trans);
+ int (*start_hw)(struct iwl_trans *iwl_trans, bool low_power);
void (*op_mode_leave)(struct iwl_trans *iwl_trans);
int (*start_fw)(struct iwl_trans *trans, const struct fw_img *fw,
bool run_in_rfkill);
int (*update_sf)(struct iwl_trans *trans,
struct iwl_sf_region *st_fwrd_space);
void (*fw_alive)(struct iwl_trans *trans, u32 scd_addr);
- void (*stop_device)(struct iwl_trans *trans);
+ void (*stop_device)(struct iwl_trans *trans, bool low_power);
void (*d3_suspend)(struct iwl_trans *trans, bool test);
int (*d3_resume)(struct iwl_trans *trans, enum iwl_d3_status *status,
trans->ops->configure(trans, trans_cfg);
}
-static inline int iwl_trans_start_hw(struct iwl_trans *trans)
+static inline int _iwl_trans_start_hw(struct iwl_trans *trans, bool low_power)
{
might_sleep();
- return trans->ops->start_hw(trans);
+ return trans->ops->start_hw(trans, low_power);
+}
+
+static inline int iwl_trans_start_hw(struct iwl_trans *trans)
+{
+ return trans->ops->start_hw(trans, true);
}
static inline void iwl_trans_op_mode_leave(struct iwl_trans *trans)
return 0;
}
-static inline void iwl_trans_stop_device(struct iwl_trans *trans)
+static inline void _iwl_trans_stop_device(struct iwl_trans *trans,
+ bool low_power)
{
might_sleep();
- trans->ops->stop_device(trans);
+ trans->ops->stop_device(trans, low_power);
trans->state = IWL_TRANS_NO_FW;
}
+static inline void iwl_trans_stop_device(struct iwl_trans *trans)
+{
+ _iwl_trans_stop_device(trans, true);
+}
+
static inline void iwl_trans_d3_suspend(struct iwl_trans *trans, bool test)
{
might_sleep();
struct iwl_host_cmd cmd = {
.id = BT_CONFIG,
.len = { sizeof(*bt_cmd), },
- .dataflags = { IWL_HCMD_DFL_NOCOPY, },
+ .dataflags = { IWL_HCMD_DFL_DUP, },
.flags = CMD_ASYNC,
};
struct iwl_mvm_sta *mvmsta;
results->matched_profiles = le32_to_cpu(query->matched_profiles);
memcpy(results->matches, query->matches, sizeof(results->matches));
-#ifdef CPTCFG_IWLWIFI_DEBUGFS
+#ifdef CONFIG_IWLWIFI_DEBUGFS
mvm->last_netdetect_scans = le32_to_cpu(query->n_scans_done);
#endif
int i, j, n_matches, ret;
fw_status = iwl_mvm_get_wakeup_status(mvm, vif);
- if (!IS_ERR_OR_NULL(fw_status))
+ if (!IS_ERR_OR_NULL(fw_status)) {
reasons = le32_to_cpu(fw_status->wakeup_reasons);
+ kfree(fw_status);
+ }
if (reasons & IWL_WOWLAN_WAKEUP_BY_RFKILL_DEASSERTED)
wakeup.rfkill_release = true;
/* get the BSS vif pointer again */
vif = iwl_mvm_get_bss_vif(mvm);
if (IS_ERR_OR_NULL(vif))
- goto out_unlock;
+ goto err;
ret = iwl_trans_d3_resume(mvm->trans, &d3_status, test);
if (ret)
- goto out_unlock;
+ goto err;
if (d3_status != IWL_D3_STATUS_ALIVE) {
IWL_INFO(mvm, "Device was reset during suspend\n");
- goto out_unlock;
+ goto err;
}
/* query SRAM first in case we want event logging */
goto out_iterate;
}
- out_unlock:
+err:
+ iwl_mvm_free_nd(mvm);
mutex_unlock(&mvm->mutex);
out_iterate:
/* return 1 to reconfigure the device */
set_bit(IWL_MVM_STATUS_IN_HW_RESTART, &mvm->status);
set_bit(IWL_MVM_STATUS_D3_RECONFIG, &mvm->status);
+
+ /* We always return 1, which causes mac80211 to do a reconfig
+ * with IEEE80211_RECONFIG_TYPE_RESTART. This type of
+ * reconfig calls iwl_mvm_restart_complete(), where we unref
+ * the IWL_MVM_REF_UCODE_DOWN, so we need to take the
+ * reference here.
+ */
+ iwl_mvm_ref(mvm, IWL_MVM_REF_UCODE_DOWN);
return 1;
}
__iwl_mvm_resume(mvm, true);
rtnl_unlock();
iwl_abort_notification_waits(&mvm->notif_wait);
- iwl_mvm_ref(mvm, IWL_MVM_REF_UCODE_DOWN);
ieee80211_restart_hw(mvm->hw);
/* wait for restart and disconnect all interfaces */
u8 reserved[3];
} __packed;
+/**
+ * struct iwl_reduce_tx_power_cmd - TX power reduction command
+ * REDUCE_TX_POWER_CMD = 0x9f
+ * @flags: (reserved for future implementation)
+ * @mac_context_id: id of the mac ctx for which we are reducing TX power.
+ * @pwr_restriction: TX power restriction in dBms.
+ */
+struct iwl_reduce_tx_power_cmd {
+ u8 flags;
+ u8 mac_context_id;
+ __le16 pwr_restriction;
+} __packed; /* TX_REDUCED_POWER_API_S_VER_1 */
+
+/**
+ * struct iwl_dev_tx_power_cmd - TX power reduction command
+ * REDUCE_TX_POWER_CMD = 0x9f
+ * @set_mode: 0 - MAC tx power, 1 - device tx power
+ * @mac_context_id: id of the mac ctx for which we are reducing TX power.
+ * @pwr_restriction: TX power restriction in 1/8 dBms.
+ * @dev_24: device TX power restriction in 1/8 dBms
+ * @dev_52_low: device TX power restriction upper band - low
+ * @dev_52_high: device TX power restriction upper band - high
+ */
+struct iwl_dev_tx_power_cmd {
+ __le32 set_mode;
+ __le32 mac_context_id;
+ __le16 pwr_restriction;
+ __le16 dev_24;
+ __le16 dev_52_low;
+ __le16 dev_52_high;
+} __packed; /* TX_REDUCED_POWER_API_S_VER_2 */
+
+#define IWL_DEV_MAX_TX_POWER 0x7FFF
+
/**
* struct iwl_beacon_filter_cmd
* REPLY_BEACON_FILTERING_CMD = 0xd2 (command)
SCAN_COMP_STATUS_ERR_ALLOC_TE = 0x0C,
};
-/**
- * struct iwl_scan_results_notif - scan results for one channel
- * ( SCAN_RESULTS_NOTIFICATION = 0x83 )
- * @channel: which channel the results are from
- * @band: 0 for 5.2 GHz, 1 for 2.4 GHz
- * @probe_status: SCAN_PROBE_STATUS_*, indicates success of probe request
- * @num_probe_not_sent: # of request that weren't sent due to not enough time
- * @duration: duration spent in channel, in usecs
- * @statistics: statistics gathered for this channel
- */
-struct iwl_scan_results_notif {
- u8 channel;
- u8 band;
- u8 probe_status;
- u8 num_probe_not_sent;
- __le32 duration;
- __le32 statistics[SCAN_RESULTS_STATISTICS];
-} __packed; /* SCAN_RESULT_NTF_API_S_VER_2 */
-
-/**
- * struct iwl_scan_complete_notif - notifies end of scanning (all channels)
- * ( SCAN_COMPLETE_NOTIFICATION = 0x84 )
- * @scanned_channels: number of channels scanned (and number of valid results)
- * @status: one of SCAN_COMP_STATUS_*
- * @bt_status: BT on/off status
- * @last_channel: last channel that was scanned
- * @tsf_low: TSF timer (lower half) in usecs
- * @tsf_high: TSF timer (higher half) in usecs
- * @results: array of scan results, only "scanned_channels" of them are valid
- */
-struct iwl_scan_complete_notif {
- u8 scanned_channels;
- u8 status;
- u8 bt_status;
- u8 last_channel;
- __le32 tsf_low;
- __le32 tsf_high;
- struct iwl_scan_results_notif results[];
-} __packed; /* SCAN_COMPLETE_NTF_API_S_VER_2 */
-
/* scan offload */
#define IWL_SCAN_MAX_BLACKLIST_LEN 64
#define IWL_SCAN_SHORT_BLACKLIST_LEN 16
} __packed;
/**
- * struct iwl_lmac_scan_results_notif - scan results for one channel -
+ * struct iwl_scan_results_notif - scan results for one channel -
* SCAN_RESULT_NTF_API_S_VER_3
* @channel: which channel the results are from
* @band: 0 for 5.2 GHz, 1 for 2.4 GHz
* @num_probe_not_sent: # of request that weren't sent due to not enough time
* @duration: duration spent in channel, in usecs
*/
-struct iwl_lmac_scan_results_notif {
+struct iwl_scan_results_notif {
u8 channel;
u8 band;
u8 probe_status;
__le32 valid;
} __packed;
-/**
- * struct iwl_reduce_tx_power_cmd - TX power reduction command
- * REDUCE_TX_POWER_CMD = 0x9f
- * @flags: (reserved for future implementation)
- * @mac_context_id: id of the mac ctx for which we are reducing TX power.
- * @pwr_restriction: TX power restriction in dBms.
- */
-struct iwl_reduce_tx_power_cmd {
- u8 flags;
- u8 mac_context_id;
- __le16 pwr_restriction;
-} __packed; /* TX_REDUCED_POWER_API_S_VER_1 */
-
/*
* Calibration control struct.
* Sent as part of the phy configuration command.
* GPL LICENSE SUMMARY
*
* Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
* BSD LICENSE
*
* Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
lockdep_assert_held(&mvm->mutex);
- if (WARN_ON_ONCE(mvm->init_ucode_complete || mvm->calibrating))
+ if (WARN_ON_ONCE(mvm->calibrating))
return 0;
iwl_init_notification_wait(&mvm->notif_wait,
*/
ret = iwl_wait_notification(&mvm->notif_wait, &calib_wait,
MVM_UCODE_CALIB_TIMEOUT);
- if (!ret)
- mvm->init_ucode_complete = true;
if (ret && iwl_mvm_is_radio_killed(mvm)) {
IWL_DEBUG_RF_KILL(mvm, "RFKILL while calibrating.\n");
mvm->fw_dump_desc = desc;
- /* stop recording */
- if (mvm->cfg->device_family == IWL_DEVICE_FAMILY_7000) {
- iwl_set_bits_prph(mvm->trans, MON_BUFF_SAMPLE_CTL, 0x100);
- } else {
- iwl_write_prph(mvm->trans, DBGC_IN_SAMPLE, 0);
- /* wait before we collect the data till the DBGC stop */
- udelay(100);
- }
-
queue_delayed_work(system_wq, &mvm->fw_dump_wk, delay);
return 0;
* module loading, load init ucode now
* (for example, if we were in RFKILL)
*/
- if (!mvm->init_ucode_complete) {
- ret = iwl_run_init_mvm_ucode(mvm, false);
- if (ret && !iwlmvm_mod_params.init_dbg) {
- IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", ret);
- /* this can't happen */
- if (WARN_ON(ret > 0))
- ret = -ERFKILL;
- goto error;
- }
- if (!iwlmvm_mod_params.init_dbg) {
- /*
- * should stop and start HW since that INIT
- * image just loaded
- */
- iwl_trans_stop_device(mvm->trans);
- ret = iwl_trans_start_hw(mvm->trans);
- if (ret)
- return ret;
- }
+ ret = iwl_run_init_mvm_ucode(mvm, false);
+ if (ret && !iwlmvm_mod_params.init_dbg) {
+ IWL_ERR(mvm, "Failed to run INIT ucode: %d\n", ret);
+ /* this can't happen */
+ if (WARN_ON(ret > 0))
+ ret = -ERFKILL;
+ goto error;
+ }
+ if (!iwlmvm_mod_params.init_dbg) {
+ /*
+ * Stop and start the transport without entering low power
+ * mode. This will save the state of other components on the
+ * device that are triggered by the INIT firwmare (MFUART).
+ */
+ _iwl_trans_stop_device(mvm->trans, false);
+ _iwl_trans_start_hw(mvm->trans, false);
+ if (ret)
+ return ret;
}
if (iwlmvm_mod_params.init_dbg)
clear_bit(IWL_MVM_STATUS_IN_HW_RESTART, &mvm->status);
iwl_mvm_d0i3_enable_tx(mvm, NULL);
- ret = iwl_mvm_update_quotas(mvm, false, NULL);
+ ret = iwl_mvm_update_quotas(mvm, true, NULL);
if (ret)
IWL_ERR(mvm, "Failed to update quotas after restart (%d)\n",
ret);
return NULL;
}
-static int iwl_mvm_set_tx_power(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
- s8 tx_power)
+static int iwl_mvm_set_tx_power_old(struct iwl_mvm *mvm,
+ struct ieee80211_vif *vif, s8 tx_power)
{
/* FW is in charge of regulatory enforcement */
struct iwl_reduce_tx_power_cmd reduce_txpwr_cmd = {
&reduce_txpwr_cmd);
}
+static int iwl_mvm_set_tx_power(struct iwl_mvm *mvm, struct ieee80211_vif *vif,
+ s16 tx_power)
+{
+ struct iwl_dev_tx_power_cmd cmd = {
+ .set_mode = 0,
+ .mac_context_id =
+ cpu_to_le32(iwl_mvm_vif_from_mac80211(vif)->id),
+ .pwr_restriction = cpu_to_le16(8 * tx_power),
+ };
+
+ if (!(mvm->fw->ucode_capa.api[0] & IWL_UCODE_TLV_API_TX_POWER_DEV))
+ return iwl_mvm_set_tx_power_old(mvm, vif, tx_power);
+
+ if (tx_power == IWL_DEFAULT_MAX_TX_POWER)
+ cmd.pwr_restriction = cpu_to_le16(IWL_DEV_MAX_TX_POWER);
+
+ return iwl_mvm_send_cmd_pdu(mvm, REDUCE_TX_POWER_CMD, 0,
+ sizeof(cmd), &cmd);
+}
+
static int iwl_mvm_mac_add_interface(struct ieee80211_hw *hw,
struct ieee80211_vif *vif)
{
if (!iwl_fw_dbg_trigger_enabled(mvm->fw, FW_DBG_TRIGGER_MLME))
return;
- if (event->u.mlme.status == MLME_SUCCESS)
- return;
-
trig = iwl_fw_dbg_get_trigger(mvm->fw, FW_DBG_TRIGGER_MLME);
trig_mlme = (void *)trig->data;
if (!iwl_fw_dbg_trigger_check_stop(mvm, vif, trig))
enum iwl_ucode_type cur_ucode;
bool ucode_loaded;
- bool init_ucode_complete;
bool calibrating;
u32 error_event_table;
u32 log_event_table;
return;
mutex_lock(&mvm->mutex);
+
+ /* stop recording */
+ if (mvm->cfg->device_family == IWL_DEVICE_FAMILY_7000) {
+ iwl_set_bits_prph(mvm->trans, MON_BUFF_SAMPLE_CTL, 0x100);
+ } else {
+ iwl_write_prph(mvm->trans, DBGC_IN_SAMPLE, 0);
+ /* wait before we collect the data till the DBGC stop */
+ udelay(100);
+ }
+
iwl_mvm_fw_error_dump(mvm);
/* start recording again if the firmware is not crashed */
ieee80211_iterate_active_interfaces(
mvm->hw, IEEE80211_IFACE_ITER_NORMAL,
iwl_mvm_d0i3_disconnect_iter, mvm);
-
- iwl_free_resp(&get_status_cmd);
out:
iwl_mvm_d0i3_enable_tx(mvm, qos_seq);
+ /* qos_seq might point inside resp_pkt, so free it only now */
+ if (get_status_cmd.resp_pkt)
+ iwl_free_resp(&get_status_cmd);
+
/* the FW might have updated the regdomain */
iwl_mvm_update_changed_regdom(mvm);
if (iwl_mvm_vif_low_latency(mvmvif) && mvmsta->vif->p2p)
return false;
+ if (mvm->nvm_data->sku_cap_mimo_disabled)
+ return false;
+
return true;
}
if (vif->type != NL80211_IFTYPE_STATION)
return;
+ if (sig == 0) {
+ IWL_DEBUG_RX(mvm, "RSSI is 0 - skip signal based decision\n");
+ return;
+ }
+
mvmvif->bf_data.ave_beacon_signal = sig;
/* BT Coex */
struct iwl_device_cmd *cmd)
{
struct iwl_rx_packet *pkt = rxb_addr(rxb);
- struct iwl_scan_complete_notif *notif = (void *)pkt->data;
+ struct iwl_lmac_scan_complete_notif *notif = (void *)pkt->data;
IWL_DEBUG_SCAN(mvm,
"Scan offload iteration complete: status=0x%x scanned channels=%d\n",
*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2007 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2007 - 2015 Intel Corporation. All rights reserved.
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
- * Copyright(c) 2013 - 2014 Intel Mobile Communications GmbH
+ * Copyright(c) 2005 - 2015 Intel Corporation. All rights reserved.
+ * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
static void iwl_pcie_alloc_fw_monitor(struct iwl_trans *trans)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
- struct page *page;
+ struct page *page = NULL;
dma_addr_t phys;
u32 size;
u8 power;
DMA_FROM_DEVICE);
if (dma_mapping_error(trans->dev, phys)) {
__free_pages(page, order);
+ page = NULL;
continue;
}
IWL_INFO(trans,
iwl_pcie_tx_start(trans, scd_addr);
}
-static void iwl_trans_pcie_stop_device(struct iwl_trans *trans)
+static void iwl_trans_pcie_stop_device(struct iwl_trans *trans, bool low_power)
{
struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans);
bool hw_rfkill, was_hw_rfkill;
iwl_pcie_rx_stop(trans);
/* Power-down device's busmaster DMA clocks */
- iwl_write_prph(trans, APMG_CLK_DIS_REG,
- APMG_CLK_VAL_DMA_CLK_RQT);
- udelay(5);
+ if (trans->cfg->device_family != IWL_DEVICE_FAMILY_8000) {
+ iwl_write_prph(trans, APMG_CLK_DIS_REG,
+ APMG_CLK_VAL_DMA_CLK_RQT);
+ udelay(5);
+ }
}
/* Make sure (redundant) we've released our request to stay awake */
void iwl_trans_pcie_rf_kill(struct iwl_trans *trans, bool state)
{
if (iwl_op_mode_hw_rf_kill(trans->op_mode, state))
- iwl_trans_pcie_stop_device(trans);
+ iwl_trans_pcie_stop_device(trans, true);
}
static void iwl_trans_pcie_d3_suspend(struct iwl_trans *trans, bool test)
return 0;
}
-static int iwl_trans_pcie_start_hw(struct iwl_trans *trans)
+static int iwl_trans_pcie_start_hw(struct iwl_trans *trans, bool low_power)
{
bool hw_rfkill;
int err;
do {
status = usb_control_msg(udev, pipe, request, reqtype, value,
- index, pdata, len, 0); /*max. timeout*/
+ index, pdata, len, 1000);
if (status < 0) {
/* firmware download is checksumed, don't retry */
if ((value >= FW_8192C_START_ADDRESS &&
goto err;
}
+ queue->credit_bytes = credit_bytes;
queue->remaining_credit = credit_bytes;
queue->credit_usec = credit_usec;
if (netif_running(info->netdev))
napi_disable(&queue->napi);
+ del_timer_sync(&queue->rx_refill_timer);
netif_napi_del(&queue->napi);
}
static int xennet_remove(struct xenbus_device *dev)
{
struct netfront_info *info = dev_get_drvdata(&dev->dev);
- unsigned int num_queues = info->netdev->real_num_tx_queues;
- struct netfront_queue *queue = NULL;
- unsigned int i = 0;
dev_dbg(&dev->dev, "%s\n", dev->nodename);
unregister_netdev(info->netdev);
- for (i = 0; i < num_queues; ++i) {
- queue = &info->queues[i];
- del_timer_sync(&queue->rx_refill_timer);
- }
-
- if (num_queues) {
- kfree(info->queues);
- info->queues = NULL;
- }
-
+ xennet_destroy_queues(info);
xennet_free_netdev(info->netdev);
return 0;
BUG();
return -1;
}
- printk("superio_fixup_irq(%s) ven 0x%x dev 0x%x from %pf\n",
+ printk(KERN_DEBUG "superio_fixup_irq(%s) ven 0x%x dev 0x%x from %ps\n",
pci_name(pcidev),
pcidev->vendor, pcidev->device,
__builtin_return_address(0));
CYGNUS_PINRANGE(87, 104, 12),
CYGNUS_PINRANGE(99, 102, 2),
CYGNUS_PINRANGE(101, 90, 4),
- CYGNUS_PINRANGE(105, 116, 10),
+ CYGNUS_PINRANGE(105, 116, 6),
+ CYGNUS_PINRANGE(111, 100, 2),
+ CYGNUS_PINRANGE(113, 122, 4),
CYGNUS_PINRANGE(123, 11, 1),
CYGNUS_PINRANGE(124, 38, 4),
CYGNUS_PINRANGE(128, 43, 1),
chv_gpio_irq_mask_unmask(d, false);
}
+static unsigned chv_gpio_irq_startup(struct irq_data *d)
+{
+ /*
+ * Check if the interrupt has been requested with 0 as triggering
+ * type. In that case it is assumed that the current values
+ * programmed to the hardware are used (e.g BIOS configured
+ * defaults).
+ *
+ * In that case ->irq_set_type() will never be called so we need to
+ * read back the values from hardware now, set correct flow handler
+ * and update mappings before the interrupt is being used.
+ */
+ if (irqd_get_trigger_type(d) == IRQ_TYPE_NONE) {
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+ struct chv_pinctrl *pctrl = gpiochip_to_pinctrl(gc);
+ unsigned offset = irqd_to_hwirq(d);
+ int pin = chv_gpio_offset_to_pin(pctrl, offset);
+ irq_flow_handler_t handler;
+ unsigned long flags;
+ u32 intsel, value;
+
+ intsel = readl(chv_padreg(pctrl, pin, CHV_PADCTRL0));
+ intsel &= CHV_PADCTRL0_INTSEL_MASK;
+ intsel >>= CHV_PADCTRL0_INTSEL_SHIFT;
+
+ value = readl(chv_padreg(pctrl, pin, CHV_PADCTRL1));
+ if (value & CHV_PADCTRL1_INTWAKECFG_LEVEL)
+ handler = handle_level_irq;
+ else
+ handler = handle_edge_irq;
+
+ spin_lock_irqsave(&pctrl->lock, flags);
+ if (!pctrl->intr_lines[intsel]) {
+ __irq_set_handler_locked(d->irq, handler);
+ pctrl->intr_lines[intsel] = offset;
+ }
+ spin_unlock_irqrestore(&pctrl->lock, flags);
+ }
+
+ chv_gpio_irq_unmask(d);
+ return 0;
+}
+
static int chv_gpio_irq_type(struct irq_data *d, unsigned type)
{
struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
static struct irq_chip chv_gpio_irqchip = {
.name = "chv-gpio",
+ .irq_startup = chv_gpio_irq_startup,
.irq_ack = chv_gpio_irq_ack,
.irq_mask = chv_gpio_irq_mask,
.irq_unmask = chv_gpio_irq_unmask,
domain->chip.direction_output = meson_gpio_direction_output;
domain->chip.get = meson_gpio_get;
domain->chip.set = meson_gpio_set;
- domain->chip.base = -1;
+ domain->chip.base = domain->data->pin_base;
domain->chip.ngpio = domain->data->num_pins;
domain->chip.can_sleep = false;
domain->chip.of_node = domain->of_node;
.banks = meson8b_banks,
.num_banks = ARRAY_SIZE(meson8b_banks),
.pin_base = 0,
- .num_pins = 83,
+ .num_pins = 130,
},
{
.name = "ao-bank",
.banks = meson8b_ao_banks,
.num_banks = ARRAY_SIZE(meson8b_ao_banks),
- .pin_base = 83,
+ .pin_base = 130,
.num_pins = 16,
},
};
return snprintf(buf, PAGE_SIZE, "%d\n", hotkey_wakeup_reason);
}
-static DEVICE_ATTR_RO(hotkey_wakeup_reason);
+static DEVICE_ATTR(wakeup_reason, S_IRUGO, hotkey_wakeup_reason_show, NULL);
static void hotkey_wakeup_reason_notify_change(void)
{
return snprintf(buf, PAGE_SIZE, "%d\n", hotkey_autosleep_ack);
}
-static DEVICE_ATTR_RO(hotkey_wakeup_hotunplug_complete);
+static DEVICE_ATTR(wakeup_hotunplug_complete, S_IRUGO,
+ hotkey_wakeup_hotunplug_complete_show, NULL);
static void hotkey_wakeup_hotunplug_complete_notify_change(void)
{
&dev_attr_hotkey_enable.attr,
&dev_attr_hotkey_bios_enabled.attr,
&dev_attr_hotkey_bios_mask.attr,
- &dev_attr_hotkey_wakeup_reason.attr,
- &dev_attr_hotkey_wakeup_hotunplug_complete.attr,
+ &dev_attr_wakeup_reason.attr,
+ &dev_attr_wakeup_hotunplug_complete.attr,
&dev_attr_hotkey_mask.attr,
&dev_attr_hotkey_all_mask.attr,
&dev_attr_hotkey_recommended_mask.attr,
attr, buf, count);
}
-static DEVICE_ATTR_RW(wan_enable);
+static DEVICE_ATTR(wwan_enable, S_IWUSR | S_IRUGO,
+ wan_enable_show, wan_enable_store);
/* --------------------------------------------------------------------- */
static struct attribute *wan_attributes[] = {
- &dev_attr_wan_enable.attr,
+ &dev_attr_wwan_enable.attr,
NULL
};
return count;
}
-static DEVICE_ATTR_RW(fan_pwm1_enable);
+static DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
+ fan_pwm1_enable_show, fan_pwm1_enable_store);
/* sysfs fan pwm1 ------------------------------------------------------ */
static ssize_t fan_pwm1_show(struct device *dev,
return (rc) ? rc : count;
}
-static DEVICE_ATTR_RW(fan_pwm1);
+static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, fan_pwm1_show, fan_pwm1_store);
/* sysfs fan fan1_input ------------------------------------------------ */
static ssize_t fan_fan1_input_show(struct device *dev,
return snprintf(buf, PAGE_SIZE, "%u\n", speed);
}
-static DEVICE_ATTR_RO(fan_fan1_input);
+static DEVICE_ATTR(fan1_input, S_IRUGO, fan_fan1_input_show, NULL);
/* sysfs fan fan2_input ------------------------------------------------ */
static ssize_t fan_fan2_input_show(struct device *dev,
return snprintf(buf, PAGE_SIZE, "%u\n", speed);
}
-static DEVICE_ATTR_RO(fan_fan2_input);
+static DEVICE_ATTR(fan2_input, S_IRUGO, fan_fan2_input_show, NULL);
/* sysfs fan fan_watchdog (hwmon driver) ------------------------------- */
static ssize_t fan_fan_watchdog_show(struct device_driver *drv,
/* --------------------------------------------------------------------- */
static struct attribute *fan_attributes[] = {
- &dev_attr_fan_pwm1_enable.attr, &dev_attr_fan_pwm1.attr,
- &dev_attr_fan_fan1_input.attr,
+ &dev_attr_pwm1_enable.attr, &dev_attr_pwm1.attr,
+ &dev_attr_fan1_input.attr,
NULL, /* for fan2_input */
NULL
};
if (tp_features.second_fan) {
/* attach second fan tachometer */
fan_attributes[ARRAY_SIZE(fan_attributes)-2] =
- &dev_attr_fan_fan2_input.attr;
+ &dev_attr_fan2_input.attr;
}
rc = sysfs_create_group(&tpacpi_sensors_pdev->dev.kobj,
&fan_attr_group);
return snprintf(buf, PAGE_SIZE, "%s\n", TPACPI_NAME);
}
-static DEVICE_ATTR_RO(thinkpad_acpi_pdev_name);
+static DEVICE_ATTR(name, S_IRUGO, thinkpad_acpi_pdev_name_show, NULL);
/* --------------------------------------------------------------------- */
hwmon_device_unregister(tpacpi_hwmon);
if (tp_features.sensors_pdev_attrs_registered)
- device_remove_file(&tpacpi_sensors_pdev->dev,
- &dev_attr_thinkpad_acpi_pdev_name);
+ device_remove_file(&tpacpi_sensors_pdev->dev, &dev_attr_name);
if (tpacpi_sensors_pdev)
platform_device_unregister(tpacpi_sensors_pdev);
if (tpacpi_pdev)
thinkpad_acpi_module_exit();
return ret;
}
- ret = device_create_file(&tpacpi_sensors_pdev->dev,
- &dev_attr_thinkpad_acpi_pdev_name);
+ ret = device_create_file(&tpacpi_sensors_pdev->dev, &dev_attr_name);
if (ret) {
pr_err("unable to create sysfs hwmon device attributes\n");
thinkpad_acpi_module_exit();
module_platform_driver(axp288_fuel_gauge_driver);
+MODULE_AUTHOR("Ramakrishna Pallala <ramakrishna.pallala@intel.com>");
MODULE_AUTHOR("Todd Brandt <todd.e.brandt@linux.intel.com>");
MODULE_DESCRIPTION("Xpower AXP288 Fuel Gauge Driver");
MODULE_LICENSE("GPL");
}
module_exit(bq27x00_battery_exit);
+#ifdef CONFIG_BATTERY_BQ27X00_PLATFORM
+MODULE_ALIAS("platform:bq27000-battery");
+#endif
+
+#ifdef CONFIG_BATTERY_BQ27X00_I2C
+MODULE_ALIAS("i2c:bq27000-battery");
+#endif
+
MODULE_AUTHOR("Rodolfo Giometti <giometti@linux.it>");
MODULE_DESCRIPTION("BQ27x00 battery monitor driver");
MODULE_LICENSE("GPL");
goto err_psy_reg_main;
}
- psy_main_cfg.drv_data = &collie_bat_bu;
+ psy_bu_cfg.drv_data = &collie_bat_bu;
collie_bat_bu.psy = power_supply_register(&dev->ucb->dev,
&collie_bat_bu_desc,
&psy_bu_cfg);
config POWER_RESET_BRCMSTB
bool "Broadcom STB reset driver"
depends on ARM || MIPS || COMPILE_TEST
+ depends on MFD_SYSCON
default ARCH_BRCMSTB
help
This driver provides restart support for Broadcom STB boards.
res = platform_get_resource(pdev, IORESOURCE_MEM, idx + 1 );
at91_ramc_base[idx] = devm_ioremap(&pdev->dev, res->start,
resource_size(res));
- if (IS_ERR(at91_ramc_base[idx])) {
+ if (!at91_ramc_base[idx]) {
dev_err(&pdev->dev, "Could not map ram controller address\n");
- return PTR_ERR(at91_ramc_base[idx]);
+ return -ENOMEM;
}
}
static void ltc2952_poweroff_start_wde(struct ltc2952_poweroff *data)
{
- if (hrtimer_start(&data->timer_wde, data->wde_interval,
- HRTIMER_MODE_REL)) {
- /*
- * The device will not toggle the watchdog reset,
- * thus shut down is only safe if the PowerPath controller
- * has a long enough time-off before triggering a hardware
- * power-off.
- *
- * Only sending a warning as the system will power-off anyway
- */
- dev_err(data->dev, "unable to start the timer\n");
- }
+ hrtimer_start(&data->timer_wde, data->wde_interval, HRTIMER_MODE_REL);
}
static enum hrtimer_restart
}
if (gpiod_get_value(data->gpio_trigger)) {
- if (hrtimer_start(&data->timer_trigger, data->trigger_delay,
- HRTIMER_MODE_REL))
- dev_err(data->dev, "unable to start the wait timer\n");
+ hrtimer_start(&data->timer_trigger, data->trigger_delay,
+ HRTIMER_MODE_REL);
} else {
hrtimer_cancel(&data->timer_trigger);
/* omitting return value check, timer should have been valid */
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/pwm.h>
#include <linux/regmap.h>
#define PERIP_PWM_PDM_CONTROL_CH_MASK 0x1
#define PERIP_PWM_PDM_CONTROL_CH_SHIFT(ch) ((ch) * 4)
-#define MAX_TMBASE_STEPS 65536
+/*
+ * PWM period is specified with a timebase register,
+ * in number of step periods. The PWM duty cycle is also
+ * specified in step periods, in the [0, $timebase] range.
+ * In other words, the timebase imposes the duty cycle
+ * resolution. Therefore, let's constraint the timebase to
+ * a minimum value to allow a sane range of duty cycle values.
+ * Imposing a minimum timebase, will impose a maximum PWM frequency.
+ *
+ * The value chosen is completely arbitrary.
+ */
+#define MIN_TMBASE_STEPS 16
+
+struct img_pwm_soc_data {
+ u32 max_timebase;
+};
struct img_pwm_chip {
struct device *dev;
struct clk *sys_clk;
void __iomem *base;
struct regmap *periph_regs;
+ int max_period_ns;
+ int min_period_ns;
+ const struct img_pwm_soc_data *data;
};
static inline struct img_pwm_chip *to_img_pwm_chip(struct pwm_chip *chip)
u32 val, div, duty, timebase;
unsigned long mul, output_clk_hz, input_clk_hz;
struct img_pwm_chip *pwm_chip = to_img_pwm_chip(chip);
+ unsigned int max_timebase = pwm_chip->data->max_timebase;
+
+ if (period_ns < pwm_chip->min_period_ns ||
+ period_ns > pwm_chip->max_period_ns) {
+ dev_err(chip->dev, "configured period not in range\n");
+ return -ERANGE;
+ }
input_clk_hz = clk_get_rate(pwm_chip->pwm_clk);
output_clk_hz = DIV_ROUND_UP(NSEC_PER_SEC, period_ns);
mul = DIV_ROUND_UP(input_clk_hz, output_clk_hz);
- if (mul <= MAX_TMBASE_STEPS) {
+ if (mul <= max_timebase) {
div = PWM_CTRL_CFG_NO_SUB_DIV;
timebase = DIV_ROUND_UP(mul, 1);
- } else if (mul <= MAX_TMBASE_STEPS * 8) {
+ } else if (mul <= max_timebase * 8) {
div = PWM_CTRL_CFG_SUB_DIV0;
timebase = DIV_ROUND_UP(mul, 8);
- } else if (mul <= MAX_TMBASE_STEPS * 64) {
+ } else if (mul <= max_timebase * 64) {
div = PWM_CTRL_CFG_SUB_DIV1;
timebase = DIV_ROUND_UP(mul, 64);
- } else if (mul <= MAX_TMBASE_STEPS * 512) {
+ } else if (mul <= max_timebase * 512) {
div = PWM_CTRL_CFG_SUB_DIV0_DIV1;
timebase = DIV_ROUND_UP(mul, 512);
- } else if (mul > MAX_TMBASE_STEPS * 512) {
+ } else if (mul > max_timebase * 512) {
dev_err(chip->dev,
"failed to configure timebase steps/divider value\n");
return -EINVAL;
.owner = THIS_MODULE,
};
+static const struct img_pwm_soc_data pistachio_pwm = {
+ .max_timebase = 255,
+};
+
+static const struct of_device_id img_pwm_of_match[] = {
+ {
+ .compatible = "img,pistachio-pwm",
+ .data = &pistachio_pwm,
+ },
+ { }
+};
+MODULE_DEVICE_TABLE(of, img_pwm_of_match);
+
static int img_pwm_probe(struct platform_device *pdev)
{
int ret;
+ u64 val;
+ unsigned long clk_rate;
struct resource *res;
struct img_pwm_chip *pwm;
+ const struct of_device_id *of_dev_id;
pwm = devm_kzalloc(&pdev->dev, sizeof(*pwm), GFP_KERNEL);
if (!pwm)
if (IS_ERR(pwm->base))
return PTR_ERR(pwm->base);
+ of_dev_id = of_match_device(img_pwm_of_match, &pdev->dev);
+ if (!of_dev_id)
+ return -ENODEV;
+ pwm->data = of_dev_id->data;
+
pwm->periph_regs = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
"img,cr-periph");
if (IS_ERR(pwm->periph_regs))
goto disable_sysclk;
}
+ clk_rate = clk_get_rate(pwm->pwm_clk);
+
+ /* The maximum input clock divider is 512 */
+ val = (u64)NSEC_PER_SEC * 512 * pwm->data->max_timebase;
+ do_div(val, clk_rate);
+ pwm->max_period_ns = val;
+
+ val = (u64)NSEC_PER_SEC * MIN_TMBASE_STEPS;
+ do_div(val, clk_rate);
+ pwm->min_period_ns = val;
+
pwm->chip.dev = &pdev->dev;
pwm->chip.ops = &img_pwm_ops;
pwm->chip.base = -1;
return pwmchip_remove(&pwm_chip->chip);
}
-static const struct of_device_id img_pwm_of_match[] = {
- { .compatible = "img,pistachio-pwm", },
- { }
-};
-MODULE_DEVICE_TABLE(of, img_pwm_of_match);
-
static struct platform_driver img_pwm_driver = {
.driver = {
.name = "img-pwm",
static int da9052_regulator_probe(struct platform_device *pdev)
{
+ const struct mfd_cell *cell = mfd_get_cell(pdev);
struct regulator_config config = { };
struct da9052_regulator *regulator;
struct da9052 *da9052;
regulator->da9052 = da9052;
regulator->info = find_regulator_info(regulator->da9052->chip_id,
- pdev->id);
+ cell->id);
if (regulator->info == NULL) {
dev_err(&pdev->dev, "invalid regulator ID specified\n");
return -EINVAL;
config.driver_data = regulator;
config.regmap = da9052->regmap;
if (pdata && pdata->regulators) {
- config.init_data = pdata->regulators[pdev->id];
+ config.init_data = pdata->regulators[cell->id];
} else {
#ifdef CONFIG_OF
struct device_node *nproot = da9052->dev->of_node;
static int armada38x_rtc_read_time(struct device *dev, struct rtc_time *tm)
{
struct armada38x_rtc *rtc = dev_get_drvdata(dev);
- unsigned long time, time_check, flags;
+ unsigned long time, time_check;
mutex_lock(&rtc->mutex_time);
time = readl(rtc->regs + RTC_TIME);
poll_timeout = time;
hr_time = ktime_set(0, poll_timeout);
- if (!hrtimer_is_queued(&ap_poll_timer) ||
- !hrtimer_forward(&ap_poll_timer, hrtimer_get_expires(&ap_poll_timer), hr_time)) {
- hrtimer_set_expires(&ap_poll_timer, hr_time);
- hrtimer_start_expires(&ap_poll_timer, HRTIMER_MODE_ABS);
- }
+ spin_lock_bh(&ap_poll_timer_lock);
+ hrtimer_cancel(&ap_poll_timer);
+ hrtimer_set_expires(&ap_poll_timer, hr_time);
+ hrtimer_start_expires(&ap_poll_timer, HRTIMER_MODE_ABS);
+ spin_unlock_bh(&ap_poll_timer_lock);
+
return count;
}
ktime_t hr_time;
spin_lock_bh(&ap_poll_timer_lock);
- if (hrtimer_is_queued(&ap_poll_timer) || ap_suspend_flag)
- goto out;
- if (ktime_to_ns(hrtimer_expires_remaining(&ap_poll_timer)) <= 0) {
+ if (!hrtimer_is_queued(&ap_poll_timer) && !ap_suspend_flag) {
hr_time = ktime_set(0, poll_timeout);
hrtimer_forward_now(&ap_poll_timer, hr_time);
hrtimer_restart(&ap_poll_timer);
}
-out:
spin_unlock_bh(&ap_poll_timer_lock);
}
{
int i;
- if (ap_domain_index != -1)
+ if ((ap_domain_index != -1) && (ap_test_config_domain(ap_domain_index)))
for (i = 0; i < AP_DEVICES; i++)
ap_reset_queue(AP_MKQID(i, ap_domain_index));
}
hrtimer_cancel(&ap_poll_timer);
destroy_workqueue(ap_work_queue);
tasklet_kill(&ap_tasklet);
- root_device_unregister(ap_root_device);
while ((dev = bus_find_device(&ap_bus_type, NULL, NULL,
__ap_match_all)))
{
}
for (i = 0; ap_bus_attrs[i]; i++)
bus_remove_file(&ap_bus_type, ap_bus_attrs[i]);
+ root_device_unregister(ap_root_device);
bus_unregister(&ap_bus_type);
unregister_reset_call(&ap_reset_call);
if (ap_using_interrupts())
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* Public License is included in this distribution in the file called COPYING.
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* Public License is included in this distribution in the file called COPYING.
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* Public License is included in this distribution in the file called COPYING.
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
MODULE_DESCRIPTION(DRV_DESC " " BUILD_STR);
MODULE_VERSION(BUILD_STR);
-MODULE_AUTHOR("Emulex Corporation");
+MODULE_AUTHOR("Avago Technologies");
MODULE_LICENSE("GPL");
module_param(be_iopoll_budget, int, 0);
module_param(enable_msix, int, 0);
static struct scsi_host_template beiscsi_sht = {
.module = THIS_MODULE,
- .name = "Emulex 10Gbe open-iscsi Initiator Driver",
+ .name = "Avago Technologies 10Gbe open-iscsi Initiator Driver",
.proc_name = DRV_NAME,
.queuecommand = iscsi_queuecommand,
.change_queue_depth = scsi_change_queue_depth,
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
#define DRV_NAME "be2iscsi"
#define BUILD_STR "10.4.114.0"
-#define BE_NAME "Emulex OneConnect" \
+#define BE_NAME "Avago Technologies OneConnect" \
"Open-iSCSI Driver version" BUILD_STR
#define DRV_DESC BE_NAME " " "Driver"
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
/**
- * Copyright (C) 2005 - 2014 Emulex
+ * Copyright (C) 2005 - 2015 Avago Technologies
* All rights reserved.
*
* This program is free software; you can redistribute it and/or
* as published by the Free Software Foundation. The full GNU General
* Public License is included in this distribution in the file called COPYING.
*
- * Written by: Jayamohan Kallickal (jayamohan.kallickal@emulex.com)
+ * Written by: Jayamohan Kallickal (jayamohan.kallickal@avagotech.com)
*
* Contact Information:
- * linux-drivers@emulex.com
+ * linux-drivers@avagotech.com
*
- * Emulex
+ * Avago Technologies
* 3333 Susan Street
* Costa Mesa, CA 92626
*/
phba->lpfc_release_scsi_buf(phba, psb);
}
-/**
- * lpfc_fcpcmd_to_iocb - copy the fcp_cmd data into the IOCB
- * @data: A pointer to the immediate command data portion of the IOCB.
- * @fcp_cmnd: The FCP Command that is provided by the SCSI layer.
- *
- * The routine copies the entire FCP command from @fcp_cmnd to @data while
- * byte swapping the data to big endian format for transmission on the wire.
- **/
-static void
-lpfc_fcpcmd_to_iocb(uint8_t *data, struct fcp_cmnd *fcp_cmnd)
-{
- int i, j;
-
- for (i = 0, j = 0; i < sizeof(struct fcp_cmnd);
- i += sizeof(uint32_t), j++) {
- ((uint32_t *)data)[j] = cpu_to_be32(((uint32_t *)fcp_cmnd)[j]);
- }
-}
-
/**
* lpfc_scsi_prep_dma_buf_s3 - DMA mapping for scsi buffer to SLI3 IF spec
* @phba: The Hba for which this call is being executed.
* we need to set word 4 of IOCB here
*/
iocb_cmd->un.fcpi.fcpi_parm = scsi_bufflen(scsi_cmnd);
- lpfc_fcpcmd_to_iocb(iocb_cmd->unsli3.fcp_ext.icd, fcp_cmnd);
return 0;
}
lpfc_release_scsi_buf(phba, lpfc_cmd);
}
+/**
+ * lpfc_fcpcmd_to_iocb - copy the fcp_cmd data into the IOCB
+ * @data: A pointer to the immediate command data portion of the IOCB.
+ * @fcp_cmnd: The FCP Command that is provided by the SCSI layer.
+ *
+ * The routine copies the entire FCP command from @fcp_cmnd to @data while
+ * byte swapping the data to big endian format for transmission on the wire.
+ **/
+static void
+lpfc_fcpcmd_to_iocb(uint8_t *data, struct fcp_cmnd *fcp_cmnd)
+{
+ int i, j;
+ for (i = 0, j = 0; i < sizeof(struct fcp_cmnd);
+ i += sizeof(uint32_t), j++) {
+ ((uint32_t *)data)[j] = cpu_to_be32(((uint32_t *)fcp_cmnd)[j]);
+ }
+}
+
/**
* lpfc_scsi_prep_cmnd - Wrapper func for convert scsi cmnd to FCP info unit
* @vport: The virtual port for which this call is being executed.
fcp_cmnd->fcpCntl3 = 0;
phba->fc4ControlRequests++;
}
+ if (phba->sli_rev == 3 &&
+ !(phba->sli3_options & LPFC_SLI3_BG_ENABLED))
+ lpfc_fcpcmd_to_iocb(iocb_cmd->unsli3.fcp_ext.icd, fcp_cmnd);
/*
* Finish initializing those IOCB fields that are independent
* of the scsi_cmnd request_buffer
{
u64 start_lba = blk_rq_pos(scmd->request);
u64 end_lba = blk_rq_pos(scmd->request) + (scsi_bufflen(scmd) / 512);
+ u64 factor = scmd->device->sector_size / 512;
u64 bad_lba;
int info_valid;
/*
if (scsi_bufflen(scmd) <= scmd->device->sector_size)
return 0;
- if (scmd->device->sector_size < 512) {
- /* only legitimate sector_size here is 256 */
- start_lba <<= 1;
- end_lba <<= 1;
- } else {
- /* be careful ... don't want any overflows */
- unsigned int factor = scmd->device->sector_size / 512;
- do_div(start_lba, factor);
- do_div(end_lba, factor);
- }
+ /* be careful ... don't want any overflows */
+ do_div(start_lba, factor);
+ do_div(end_lba, factor);
/* The bad lba was reported incorrectly, we have no idea where
* the error is.
if (sector_size != 512 &&
sector_size != 1024 &&
sector_size != 2048 &&
- sector_size != 4096 &&
- sector_size != 256) {
+ sector_size != 4096) {
sd_printk(KERN_NOTICE, sdkp, "Unsupported sector size %d.\n",
sector_size);
/*
sdkp->capacity <<= 2;
else if (sector_size == 1024)
sdkp->capacity <<= 1;
- else if (sector_size == 256)
- sdkp->capacity >>= 1;
blk_queue_physical_block_size(sdp->request_queue,
sdkp->physical_block_size);
break;
default:
vm_srb->data_in = UNKNOWN_TYPE;
- vm_srb->win8_extension.srb_flags |= (SRB_FLAGS_DATA_IN |
- SRB_FLAGS_DATA_OUT);
+ vm_srb->win8_extension.srb_flags |= SRB_FLAGS_NO_DATA_TRANSFER;
break;
}
config SPI_BCM2835
tristate "BCM2835 SPI controller"
depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on GPIOLIB
help
This selects a driver for the Broadcom BCM2835 SPI master.
config SPI_FSL_DSPI
tristate "Freescale DSPI controller"
select REGMAP_MMIO
- depends on SOC_VF610 || COMPILE_TEST
+ depends on SOC_VF610 || SOC_LS1021A || COMPILE_TEST
help
This enables support for the Freescale DSPI controller in master
mode. VF610 platform uses the controller.
unsigned long xfer_time_us)
{
struct bcm2835_spi *bs = spi_master_get_devdata(master);
- unsigned long timeout = jiffies +
- max(4 * xfer_time_us * HZ / 1000000, 2uL);
+ /* set timeout to 1 second of maximum polling */
+ unsigned long timeout = jiffies + HZ;
/* enable HW block without interrupts */
bcm2835_wr(bs, BCM2835_SPI_CS, cs | BCM2835_SPI_CS_TA);
- /* set timeout to 4x the expected time, or 2 jiffies */
/* loop until finished the transfer */
while (bs->rx_len) {
/* read from fifo as much as possible */
{
struct spi_bitbang_cs *cs = spi->controller_state;
struct spi_bitbang *bitbang;
- int retval;
unsigned long flags;
bitbang = spi_master_get_devdata(spi->master);
if (!cs->txrx_word)
return -EINVAL;
- retval = bitbang->setup_transfer(spi, NULL);
- if (retval < 0)
- return retval;
+ if (bitbang->setup_transfer) {
+ int retval = bitbang->setup_transfer(spi, NULL);
+ if (retval < 0)
+ return retval;
+ }
dev_dbg(&spi->dev, "%s, %u nsec/bit\n", __func__, 2 * cs->nsecs);
/* init (-1) or override (1) transfer params */
if (do_setup != 0) {
- status = bitbang->setup_transfer(spi, t);
- if (status < 0)
- break;
+ if (bitbang->setup_transfer) {
+ status = bitbang->setup_transfer(spi, t);
+ if (status < 0)
+ break;
+ }
if (do_setup == -1)
do_setup = 0;
}
#include <linux/of_address.h>
#include <linux/spi/spi.h>
#include <linux/types.h>
+#include <linux/platform_device.h>
#include "spi-fsl-cpm.h"
#include "spi-fsl-lib.h"
if (mspi->flags & SPI_CPM2) {
pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
out_be16(spi_base, pram_ofs);
- } else {
- struct spi_pram __iomem *pram = spi_base;
- u16 rpbase = in_be16(&pram->rpbase);
-
- /* Microcode relocation patch applied? */
- if (rpbase) {
- pram_ofs = rpbase;
- } else {
- pram_ofs = cpm_muram_alloc(SPI_PRAM_SIZE, 64);
- out_be16(spi_base, pram_ofs);
- }
}
iounmap(spi_base);
struct device_node *np = dev->of_node;
const u32 *iprop;
int size;
- unsigned long pram_ofs;
unsigned long bds_ofs;
if (!(mspi->flags & SPI_CPM_MODE))
}
}
- pram_ofs = fsl_spi_cpm_get_pram(mspi);
- if (IS_ERR_VALUE(pram_ofs)) {
+ if (mspi->flags & SPI_CPM1) {
+ struct resource *res;
+ void *pram;
+
+ res = platform_get_resource(to_platform_device(dev),
+ IORESOURCE_MEM, 1);
+ pram = devm_ioremap_resource(dev, res);
+ if (IS_ERR(pram))
+ mspi->pram = NULL;
+ else
+ mspi->pram = pram;
+ } else {
+ unsigned long pram_ofs = fsl_spi_cpm_get_pram(mspi);
+
+ if (IS_ERR_VALUE(pram_ofs))
+ mspi->pram = NULL;
+ else
+ mspi->pram = cpm_muram_addr(pram_ofs);
+ }
+ if (mspi->pram == NULL) {
dev_err(dev, "can't allocate spi parameter ram\n");
goto err_pram;
}
goto err_dummy_rx;
}
- mspi->pram = cpm_muram_addr(pram_ofs);
-
mspi->tx_bd = cpm_muram_addr(bds_ofs);
mspi->rx_bd = cpm_muram_addr(bds_ofs + sizeof(*mspi->tx_bd));
err_dummy_tx:
cpm_muram_free(bds_ofs);
err_bds:
- cpm_muram_free(pram_ofs);
+ if (!(mspi->flags & SPI_CPM1))
+ cpm_muram_free(cpm_muram_offset(mspi->pram));
err_pram:
fsl_spi_free_dummy_rx();
return -ENOMEM;
struct fsl_espi_transfer *trans, u8 *rx_buff)
{
struct fsl_espi_transfer *espi_trans = trans;
- unsigned int n_tx = espi_trans->n_tx;
- unsigned int n_rx = espi_trans->n_rx;
+ unsigned int total_len = espi_trans->len;
struct spi_transfer *t;
u8 *local_buf;
u8 *rx_buf = rx_buff;
unsigned int trans_len;
unsigned int addr;
- int i, pos, loop;
+ unsigned int tx_only;
+ unsigned int rx_pos = 0;
+ unsigned int pos;
+ int i, loop;
local_buf = kzalloc(SPCOM_TRANLEN_MAX, GFP_KERNEL);
if (!local_buf) {
return;
}
- for (pos = 0, loop = 0; pos < n_rx; pos += trans_len, loop++) {
- trans_len = n_rx - pos;
- if (trans_len > SPCOM_TRANLEN_MAX - n_tx)
- trans_len = SPCOM_TRANLEN_MAX - n_tx;
+ for (pos = 0, loop = 0; pos < total_len; pos += trans_len, loop++) {
+ trans_len = total_len - pos;
i = 0;
+ tx_only = 0;
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->tx_buf) {
memcpy(local_buf + i, t->tx_buf, t->len);
i += t->len;
+ if (!t->rx_buf)
+ tx_only += t->len;
}
}
+ /* Add additional TX bytes to compensate SPCOM_TRANLEN_MAX */
+ if (loop > 0)
+ trans_len += tx_only;
+
+ if (trans_len > SPCOM_TRANLEN_MAX)
+ trans_len = SPCOM_TRANLEN_MAX;
+
+ /* Update device offset */
if (pos > 0) {
addr = fsl_espi_cmd2addr(local_buf);
- addr += pos;
+ addr += rx_pos;
fsl_espi_addr2cmd(addr, local_buf);
}
- espi_trans->n_tx = n_tx;
- espi_trans->n_rx = trans_len;
- espi_trans->len = trans_len + n_tx;
+ espi_trans->len = trans_len;
espi_trans->tx_buf = local_buf;
espi_trans->rx_buf = local_buf;
fsl_espi_do_trans(m, espi_trans);
- memcpy(rx_buf + pos, espi_trans->rx_buf + n_tx, trans_len);
+ /* If there is at least one RX byte then copy it to rx_buf */
+ if (tx_only < SPCOM_TRANLEN_MAX)
+ memcpy(rx_buf + rx_pos, espi_trans->rx_buf + tx_only,
+ trans_len - tx_only);
+
+ rx_pos += trans_len - tx_only;
if (loop > 0)
- espi_trans->actual_length += espi_trans->len - n_tx;
+ espi_trans->actual_length += espi_trans->len - tx_only;
else
espi_trans->actual_length += espi_trans->len;
}
u8 *rx_buf = NULL;
unsigned int n_tx = 0;
unsigned int n_rx = 0;
+ unsigned int xfer_len = 0;
struct fsl_espi_transfer espi_trans;
list_for_each_entry(t, &m->transfers, transfer_list) {
n_rx += t->len;
rx_buf = t->rx_buf;
}
+ if ((t->tx_buf) || (t->rx_buf))
+ xfer_len += t->len;
}
espi_trans.n_tx = n_tx;
espi_trans.n_rx = n_rx;
- espi_trans.len = n_tx + n_rx;
+ espi_trans.len = xfer_len;
espi_trans.actual_length = 0;
espi_trans.status = 0;
struct omap2_mcspi *mcspi;
struct omap2_mcspi_dma *mcspi_dma;
struct spi_transfer *t;
+ int status;
spi = m->spi;
mcspi = spi_master_get_devdata(master);
tx_buf ? "tx" : "",
rx_buf ? "rx" : "",
t->bits_per_word);
- return -EINVAL;
+ status = -EINVAL;
+ goto out;
}
if (m->is_dma_mapped || len < DMA_MIN_BYTES)
if (dma_mapping_error(mcspi->dev, t->tx_dma)) {
dev_dbg(mcspi->dev, "dma %cX %d bytes error\n",
'T', len);
- return -EINVAL;
+ status = -EINVAL;
+ goto out;
}
}
if (mcspi_dma->dma_rx && rx_buf != NULL) {
if (tx_buf != NULL)
dma_unmap_single(mcspi->dev, t->tx_dma,
len, DMA_TO_DEVICE);
- return -EINVAL;
+ status = -EINVAL;
+ goto out;
}
}
}
omap2_mcspi_work(mcspi, m);
+ /* spi_finalize_current_message() changes the status inside the
+ * spi_message, save the status here. */
+ status = m->status;
+out:
spi_finalize_current_message(master);
- return 0;
+ return status;
}
static int omap2_mcspi_master_setup(struct omap2_mcspi *mcspi)
rx_dev = master->dma_rx->device->dev;
list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+ /*
+ * Restore the original value of tx_buf or rx_buf if they are
+ * NULL.
+ */
+ if (xfer->tx_buf == master->dummy_tx)
+ xfer->tx_buf = NULL;
+ if (xfer->rx_buf == master->dummy_rx)
+ xfer->rx_buf = NULL;
+
if (!master->can_dma(master, msg->spi, xfer))
continue;
/*
* Accessing PCI config without a proper delay after devices reset (not
- * GPIO reset) was causing reboots on WRT300N v1.0.
+ * GPIO reset) was causing reboots on WRT300N v1.0 (BCM4704).
* Tested delay 850 us lowered reboot chance to 50-80%, 1000 us fixed it
* completely. Flushing all writes was also tested but with no luck.
+ * The same problem was reported for WRT350N v1 (BCM4705), so we just
+ * sleep here unconditionally.
*/
- if (pc->dev->bus->chip_id == 0x4704)
- usleep_range(1000, 2000);
+ usleep_range(1000, 2000);
/* Enable PCI bridge BAR0 prefetch and burst */
val = PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
unsigned int start_flag;
unsigned int payload_size;
unsigned short packet_type;
- int dummy_cnt;
+ int total_len;
u32 packet_size_sum = r->offset;
int index;
int ret = TO_HOST_INVALID_PACKET;
break;
}
- dummy_cnt = ALIGN(MUX_HEADER_SIZE + payload_size, 4);
+ total_len = ALIGN(MUX_HEADER_SIZE + payload_size, 4);
if (len - packet_size_sum <
- MUX_HEADER_SIZE + payload_size + dummy_cnt) {
+ total_len) {
pr_err("invalid payload : %d %d %04x\n",
payload_size, len, packet_type);
break;
break;
}
- packet_size_sum += MUX_HEADER_SIZE + payload_size + dummy_cnt;
+ packet_size_sum += total_len;
if (len - packet_size_sum <= MUX_HEADER_SIZE + 2) {
ret = r->callback(NULL,
0,
struct mux_pkt_header *mux_header;
struct mux_tx *t = NULL;
static u32 seq_num = 1;
- int dummy_cnt;
int total_len;
int ret;
unsigned long flags;
spin_lock_irqsave(&mux_dev->write_lock, flags);
- dummy_cnt = ALIGN(MUX_HEADER_SIZE + len, 4);
-
- total_len = len + MUX_HEADER_SIZE + dummy_cnt;
+ total_len = ALIGN(MUX_HEADER_SIZE + len, 4);
t = alloc_mux_tx(total_len);
if (!t) {
mux_header->packet_type = __cpu_to_le16(packet_type[tty_index]);
memcpy(t->buf+MUX_HEADER_SIZE, data, len);
- memset(t->buf+MUX_HEADER_SIZE+len, 0, dummy_cnt);
+ memset(t->buf+MUX_HEADER_SIZE+len, 0, total_len - MUX_HEADER_SIZE -
+ len);
t->len = total_len;
t->callback = cb;
struct mp_ioctl_handler *phandler;
struct mp_ioctl_param *poidparam;
unsigned long BytesRead, BytesWritten, BytesNeeded;
- u8 *pparmbuf = NULL, bset;
+ u8 *pparmbuf, bset;
u16 len;
uint status;
int ret = 0;
- if ((!p->length) || (!p->pointer)) {
- ret = -EINVAL;
- goto _r871x_mp_ioctl_hdl_exit;
- }
+ if ((!p->length) || (!p->pointer))
+ return -EINVAL;
+
bset = (u8)(p->flags & 0xFFFF);
len = p->length;
- pparmbuf = NULL;
pparmbuf = memdup_user(p->pointer, len);
- if (IS_ERR(pparmbuf)) {
- ret = PTR_ERR(pparmbuf);
- goto _r871x_mp_ioctl_hdl_exit;
- }
+ if (IS_ERR(pparmbuf))
+ return PTR_ERR(pparmbuf);
+
poidparam = (struct mp_ioctl_param *)pparmbuf;
if (poidparam->subcode >= MAX_MP_IOCTL_SUBCODE) {
ret = -EINVAL;
return -ENODEV;
}
-static void __exit lynxfb_pci_remove(struct pci_dev *pdev)
+static void lynxfb_pci_remove(struct pci_dev *pdev)
{
struct fb_info *info;
struct lynx_share *share;
* Return Value: none
*/
bool CARDbUpdateTSF(struct vnt_private *pDevice, unsigned char byRxRate,
- u64 qwBSSTimestamp, u64 qwLocalTSF)
+ u64 qwBSSTimestamp)
{
+ u64 local_tsf;
u64 qwTSFOffset = 0;
- if (qwBSSTimestamp != qwLocalTSF) {
- qwTSFOffset = CARDqGetTSFOffset(byRxRate, qwBSSTimestamp, qwLocalTSF);
+ CARDbGetCurrentTSF(pDevice, &local_tsf);
+
+ if (qwBSSTimestamp != local_tsf) {
+ qwTSFOffset = CARDqGetTSFOffset(byRxRate, qwBSSTimestamp,
+ local_tsf);
/* adjust TSF, HW's TSF add TSF Offset reg */
VNSvOutPortD(pDevice->PortOffset + MAC_REG_TSFOFST, (u32)qwTSFOffset);
VNSvOutPortD(pDevice->PortOffset + MAC_REG_TSFOFST + 4, (u32)(qwTSFOffset >> 32));
bool CARDbRadioPowerOn(struct vnt_private *);
bool CARDbSetPhyParameter(struct vnt_private *, u8);
bool CARDbUpdateTSF(struct vnt_private *, unsigned char byRxRate,
- u64 qwBSSTimestamp, u64 qwLocalTSF);
+ u64 qwBSSTimestamp);
bool CARDbSetBeaconPeriod(struct vnt_private *, unsigned short wBeaconInterval);
#endif /* __CARD_H__ */
if (!(tsr1 & TSR1_TERR)) {
info->status.rates[0].idx = idx;
- info->flags |= IEEE80211_TX_STAT_ACK;
+
+ if (info->flags & IEEE80211_TX_CTL_NO_ACK)
+ info->flags |= IEEE80211_TX_STAT_NOACK_TRANSMITTED;
+ else
+ info->flags |= IEEE80211_TX_STAT_ACK;
}
return 0;
/* Only the status of first TD in the chain is correct */
if (pTD->m_td1TD1.byTCR & TCR_STP) {
if ((pTD->pTDInfo->byFlags & TD_FLAGS_NETIF_SKB) != 0) {
-
- vnt_int_report_rate(pDevice, pTD->pTDInfo, byTsr0, byTsr1);
-
if (!(byTsr1 & TSR1_TERR)) {
if (byTsr0 != 0) {
pr_debug(" Tx[%d] OK but has error. tsr1[%02X] tsr0[%02X]\n",
(int)uIdx, byTsr1, byTsr0);
}
}
+
+ vnt_int_report_rate(pDevice, pTD->pTDInfo, byTsr0, byTsr1);
+
device_free_tx_buf(pDevice, pTD);
pDevice->iTDUsed[uIdx]--;
}
skb->len, DMA_TO_DEVICE);
}
- if (pTDInfo->byFlags & TD_FLAGS_NETIF_SKB)
+ if (skb)
ieee80211_tx_status_irqsafe(pDevice->hw, skb);
- else
- dev_kfree_skb_irq(skb);
pTDInfo->skb_dma = 0;
pTDInfo->skb = NULL;
if (dma_idx == TYPE_AC0DMA)
head_td->pTDInfo->byFlags = TD_FLAGS_NETIF_SKB;
- priv->iTDUsed[dma_idx]++;
-
- /* Take ownership */
- wmb();
- head_td->m_td0TD0.f1Owner = OWNED_BY_NIC;
-
- /* get Next */
- wmb();
priv->apCurrTD[dma_idx] = head_td->next;
spin_unlock_irqrestore(&priv->lock, flags);
head_td->buff_addr = cpu_to_le32(head_td->pTDInfo->skb_dma);
+ /* Poll Transmit the adapter */
+ wmb();
+ head_td->m_td0TD0.f1Owner = OWNED_BY_NIC;
+ wmb(); /* second memory barrier */
+
if (head_td->pTDInfo->byFlags & TD_FLAGS_NETIF_SKB)
MACvTransmitAC0(priv->PortOffset);
else
MACvTransmit0(priv->PortOffset);
+ priv->iTDUsed[dma_idx]++;
+
spin_unlock_irqrestore(&priv->lock, flags);
return 0;
priv->current_aid = conf->aid;
- if (changed & BSS_CHANGED_BSSID)
+ if (changed & BSS_CHANGED_BSSID) {
+ unsigned long flags;
+
+ spin_lock_irqsave(&priv->lock, flags);
+
MACvWriteBSSIDAddress(priv->PortOffset, (u8 *)conf->bssid);
+ spin_unlock_irqrestore(&priv->lock, flags);
+ }
+
if (changed & BSS_CHANGED_BASIC_RATES) {
priv->basic_rates = conf->basic_rates;
if (changed & BSS_CHANGED_ASSOC && priv->op_mode != NL80211_IFTYPE_AP) {
if (conf->assoc) {
CARDbUpdateTSF(priv, conf->beacon_rate->hw_value,
- conf->sync_device_ts, conf->sync_tsf);
+ conf->sync_tsf);
CARDbSetBeaconPeriod(priv, conf->beacon_int);
vnt_schedule_command(priv, WLAN_CMD_SETPOWER);
}
- if (current_rate > RATE_11M)
- pkt_type = priv->packet_type;
- else
+ if (current_rate > RATE_11M) {
+ if (info->band == IEEE80211_BAND_5GHZ) {
+ pkt_type = PK_TYPE_11A;
+ } else {
+ if (tx_rate->flags & IEEE80211_TX_RC_USE_CTS_PROTECT)
+ pkt_type = PK_TYPE_11GB;
+ else
+ pkt_type = PK_TYPE_11GA;
+ }
+ } else {
pkt_type = PK_TYPE_11B;
+ }
spin_lock_irqsave(&priv->lock, flags);
.is_valid_shift = 10,
.temp_shift = 0,
.temp_mask = 0x3ff,
- .coef_b = 1169498786UL,
- .coef_m = 2000000UL,
- .coef_div = 4289,
+ .coef_b = 2931108200UL,
+ .coef_m = 5000000UL,
+ .coef_div = 10502,
.inverted = true,
};
}
+struct pkg_cstate_info {
+ bool skip;
+ int msr_index;
+ int cstate_id;
+};
+
+#define PKG_CSTATE_INIT(id) { \
+ .msr_index = MSR_PKG_C##id##_RESIDENCY, \
+ .cstate_id = id \
+ }
+
+static struct pkg_cstate_info pkg_cstates[] = {
+ PKG_CSTATE_INIT(2),
+ PKG_CSTATE_INIT(3),
+ PKG_CSTATE_INIT(6),
+ PKG_CSTATE_INIT(7),
+ PKG_CSTATE_INIT(8),
+ PKG_CSTATE_INIT(9),
+ PKG_CSTATE_INIT(10),
+ {NULL},
+};
+
static bool has_pkg_state_counter(void)
{
- u64 tmp;
- return !rdmsrl_safe(MSR_PKG_C2_RESIDENCY, &tmp) ||
- !rdmsrl_safe(MSR_PKG_C3_RESIDENCY, &tmp) ||
- !rdmsrl_safe(MSR_PKG_C6_RESIDENCY, &tmp) ||
- !rdmsrl_safe(MSR_PKG_C7_RESIDENCY, &tmp);
+ u64 val;
+ struct pkg_cstate_info *info = pkg_cstates;
+
+ /* check if any one of the counter msrs exists */
+ while (info->msr_index) {
+ if (!rdmsrl_safe(info->msr_index, &val))
+ return true;
+ info++;
+ }
+
+ return false;
}
static u64 pkg_state_counter(void)
{
u64 val;
u64 count = 0;
-
- static bool skip_c2;
- static bool skip_c3;
- static bool skip_c6;
- static bool skip_c7;
-
- if (!skip_c2) {
- if (!rdmsrl_safe(MSR_PKG_C2_RESIDENCY, &val))
- count += val;
- else
- skip_c2 = true;
- }
-
- if (!skip_c3) {
- if (!rdmsrl_safe(MSR_PKG_C3_RESIDENCY, &val))
- count += val;
- else
- skip_c3 = true;
- }
-
- if (!skip_c6) {
- if (!rdmsrl_safe(MSR_PKG_C6_RESIDENCY, &val))
- count += val;
- else
- skip_c6 = true;
- }
-
- if (!skip_c7) {
- if (!rdmsrl_safe(MSR_PKG_C7_RESIDENCY, &val))
- count += val;
- else
- skip_c7 = true;
+ struct pkg_cstate_info *info = pkg_cstates;
+
+ while (info->msr_index) {
+ if (!info->skip) {
+ if (!rdmsrl_safe(info->msr_index, &val))
+ count += val;
+ else
+ info->skip = true;
+ }
+ info++;
}
return count;
};
/* runs on Nehalem and later */
-static const struct x86_cpu_id intel_powerclamp_ids[] = {
+static const struct x86_cpu_id intel_powerclamp_ids[] __initconst = {
{ X86_VENDOR_INTEL, 6, 0x1a},
{ X86_VENDOR_INTEL, 6, 0x1c},
{ X86_VENDOR_INTEL, 6, 0x1e},
{ X86_VENDOR_INTEL, 6, 0x46},
{ X86_VENDOR_INTEL, 6, 0x4c},
{ X86_VENDOR_INTEL, 6, 0x4d},
+ { X86_VENDOR_INTEL, 6, 0x4f},
{ X86_VENDOR_INTEL, 6, 0x56},
{}
};
MODULE_DEVICE_TABLE(x86cpu, intel_powerclamp_ids);
-static int powerclamp_probe(void)
+static int __init powerclamp_probe(void)
{
if (!x86_match_cpu(intel_powerclamp_ids)) {
pr_err("Intel powerclamp does not run on family %d model %d\n",
debugfs_remove_recursive(debug_dir);
}
-static int powerclamp_init(void)
+static int __init powerclamp_init(void)
{
int retval;
int bitmap_size;
}
module_init(powerclamp_init);
-static void powerclamp_exit(void)
+static void __exit powerclamp_exit(void)
{
unregister_hotcpu_notifier(&powerclamp_cpu_notifier);
end_power_clamp();
thermal->pclk = devm_clk_get(&pdev->dev, "apb_pclk");
if (IS_ERR(thermal->pclk)) {
- error = PTR_ERR(thermal->clk);
+ error = PTR_ERR(thermal->pclk);
dev_err(&pdev->dev, "failed to get apb_pclk clock: %d\n",
error);
return error;
static inline bool of_thermal_is_trip_valid(struct thermal_zone_device *tz,
int trip)
{
- return 0;
+ return false;
}
static inline const struct thermal_trip *
of_thermal_get_trip_points(struct thermal_zone_device *tz)
TI_BANDGAP_FEATURE_FREEZE_BIT |
TI_BANDGAP_FEATURE_TALERT |
TI_BANDGAP_FEATURE_COUNTER_DELAY |
- TI_BANDGAP_FEATURE_HISTORY_BUFFER,
+ TI_BANDGAP_FEATURE_HISTORY_BUFFER |
+ TI_BANDGAP_FEATURE_ERRATA_814,
.fclock_name = "l3instr_ts_gclk_div",
.div_ck_name = "l3instr_ts_gclk_div",
.conv_table = dra752_adc_to_temp,
TI_BANDGAP_FEATURE_FREEZE_BIT |
TI_BANDGAP_FEATURE_TALERT |
TI_BANDGAP_FEATURE_COUNTER_DELAY |
- TI_BANDGAP_FEATURE_HISTORY_BUFFER,
+ TI_BANDGAP_FEATURE_HISTORY_BUFFER |
+ TI_BANDGAP_FEATURE_ERRATA_813,
.fclock_name = "l3instr_ts_gclk_div",
.div_ck_name = "l3instr_ts_gclk_div",
.conv_table = omap5430_adc_to_temp,
return ret;
}
+/**
+ * ti_errata814_bandgap_read_temp() - helper function to read dra7 sensor temperature
+ * @bgp: pointer to ti_bandgap structure
+ * @reg: desired register (offset) to be read
+ *
+ * Function to read dra7 bandgap sensor temperature. This is done separately
+ * so as to workaround the errata "Bandgap Temperature read Dtemp can be
+ * corrupted" - Errata ID: i814".
+ * Read accesses to registers listed below can be corrupted due to incorrect
+ * resynchronization between clock domains.
+ * Read access to registers below can be corrupted :
+ * CTRL_CORE_DTEMP_MPU/GPU/CORE/DSPEVE/IVA_n (n = 0 to 4)
+ * CTRL_CORE_TEMP_SENSOR_MPU/GPU/CORE/DSPEVE/IVA_n
+ *
+ * Return: the register value.
+ */
+static u32 ti_errata814_bandgap_read_temp(struct ti_bandgap *bgp, u32 reg)
+{
+ u32 val1, val2;
+
+ val1 = ti_bandgap_readl(bgp, reg);
+ val2 = ti_bandgap_readl(bgp, reg);
+
+ /* If both times we read the same value then that is right */
+ if (val1 == val2)
+ return val1;
+
+ /* if val1 and val2 are different read it third time */
+ return ti_bandgap_readl(bgp, reg);
+}
+
/**
* ti_bandgap_read_temp() - helper function to read sensor temperature
* @bgp: pointer to ti_bandgap structure
}
/* read temperature */
- temp = ti_bandgap_readl(bgp, reg);
+ if (TI_BANDGAP_HAS(bgp, ERRATA_814))
+ temp = ti_errata814_bandgap_read_temp(bgp, reg);
+ else
+ temp = ti_bandgap_readl(bgp, reg);
+
temp &= tsr->bgap_dtemp_mask;
if (TI_BANDGAP_HAS(bgp, FREEZE_BIT))
{
struct temp_sensor_data *ts_data = bgp->conf->sensors[id].ts_data;
struct temp_sensor_registers *tsr;
- u32 thresh_val, reg_val, t_hot, t_cold;
+ u32 thresh_val, reg_val, t_hot, t_cold, ctrl;
int err = 0;
tsr = bgp->conf->sensors[id].registers;
~(tsr->threshold_thot_mask | tsr->threshold_tcold_mask);
reg_val |= (t_hot << __ffs(tsr->threshold_thot_mask)) |
(t_cold << __ffs(tsr->threshold_tcold_mask));
+
+ /**
+ * Errata i813:
+ * Spurious Thermal Alert: Talert can happen randomly while the device
+ * remains under the temperature limit defined for this event to trig.
+ * This spurious event is caused by a incorrect re-synchronization
+ * between clock domains. The comparison between configured threshold
+ * and current temperature value can happen while the value is
+ * transitioning (metastable), thus causing inappropriate event
+ * generation. No spurious event occurs as long as the threshold value
+ * stays unchanged. Spurious event can be generated while a thermal
+ * alert threshold is modified in
+ * CONTROL_BANDGAP_THRESHOLD_MPU/GPU/CORE/DSPEVE/IVA_n.
+ */
+
+ if (TI_BANDGAP_HAS(bgp, ERRATA_813)) {
+ /* Mask t_hot and t_cold events at the IP Level */
+ ctrl = ti_bandgap_readl(bgp, tsr->bgap_mask_ctrl);
+
+ if (hot)
+ ctrl &= ~tsr->mask_hot_mask;
+ else
+ ctrl &= ~tsr->mask_cold_mask;
+
+ ti_bandgap_writel(bgp, ctrl, tsr->bgap_mask_ctrl);
+ }
+
+ /* Write the threshold value */
ti_bandgap_writel(bgp, reg_val, tsr->bgap_threshold);
+ if (TI_BANDGAP_HAS(bgp, ERRATA_813)) {
+ /* Unmask t_hot and t_cold events at the IP Level */
+ ctrl = ti_bandgap_readl(bgp, tsr->bgap_mask_ctrl);
+ if (hot)
+ ctrl |= tsr->mask_hot_mask;
+ else
+ ctrl |= tsr->mask_cold_mask;
+
+ ti_bandgap_writel(bgp, ctrl, tsr->bgap_mask_ctrl);
+ }
+
if (err) {
dev_err(bgp->dev, "failed to reprogram thot threshold\n");
err = -EIO;
* TI_BANDGAP_FEATURE_HISTORY_BUFFER - used when the bandgap device features
* a history buffer of temperatures.
*
+ * TI_BANDGAP_FEATURE_ERRATA_814 - used to workaorund when the bandgap device
+ * has Errata 814
+ * TI_BANDGAP_FEATURE_ERRATA_813 - used to workaorund when the bandgap device
+ * has Errata 813
* TI_BANDGAP_HAS(b, f) - macro to check if a bandgap device is capable of a
* specific feature (above) or not. Return non-zero, if yes.
*/
#define TI_BANDGAP_FEATURE_FREEZE_BIT BIT(7)
#define TI_BANDGAP_FEATURE_COUNTER_DELAY BIT(8)
#define TI_BANDGAP_FEATURE_HISTORY_BUFFER BIT(9)
+#define TI_BANDGAP_FEATURE_ERRATA_814 BIT(10)
+#define TI_BANDGAP_FEATURE_ERRATA_813 BIT(11)
#define TI_BANDGAP_HAS(b, f) \
((b)->conf->features & TI_BANDGAP_FEATURE_ ## f)
return -ENOMEM;
}
- info->irq = bind_virq_to_irq(VIRQ_CONSOLE, 0);
+ info->irq = bind_virq_to_irq(VIRQ_CONSOLE, 0, false);
info->vtermno = HVC_COOKIE;
spin_lock(&xencons_lock);
return gsmtty_modem_update(dlci, encode);
}
-static void gsmtty_remove(struct tty_driver *driver, struct tty_struct *tty)
+static void gsmtty_cleanup(struct tty_struct *tty)
{
struct gsm_dlci *dlci = tty->driver_data;
struct gsm_mux *gsm = dlci->gsm;
dlci_put(dlci);
dlci_put(gsm->dlci[0]);
mux_put(gsm);
- driver->ttys[tty->index] = NULL;
}
/* Virtual ttys for the demux */
.tiocmget = gsmtty_tiocmget,
.tiocmset = gsmtty_tiocmset,
.break_ctl = gsmtty_break_ctl,
- .remove = gsmtty_remove,
+ .cleanup = gsmtty_cleanup,
};
add_wait_queue(&tty->read_wait, &wait);
for (;;) {
- if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
+ if (test_bit(TTY_OTHER_DONE, &tty->flags)) {
ret = -EIO;
break;
}
/* set bits for operations that won't block */
if (n_hdlc->rx_buf_list.head)
mask |= POLLIN | POLLRDNORM; /* readable */
- if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
+ if (test_bit(TTY_OTHER_DONE, &tty->flags))
mask |= POLLHUP;
if (tty_hung_up_p(filp))
mask |= POLLHUP;
return ldata->commit_head - ldata->read_tail >= amt;
}
+static inline int check_other_done(struct tty_struct *tty)
+{
+ int done = test_bit(TTY_OTHER_DONE, &tty->flags);
+ if (done) {
+ /* paired with cmpxchg() in check_other_closed(); ensures
+ * read buffer head index is not stale
+ */
+ smp_mb__after_atomic();
+ }
+ return done;
+}
+
/**
* copy_from_read_buf - copy read data directly
* @tty: terminal device
struct n_tty_data *ldata = tty->disc_data;
unsigned char __user *b = buf;
DEFINE_WAIT_FUNC(wait, woken_wake_function);
- int c;
+ int c, done;
int minimum, time;
ssize_t retval = 0;
long timeout;
((minimum - (b - buf)) >= 1))
ldata->minimum_to_wake = (minimum - (b - buf));
+ done = check_other_done(tty);
+
if (!input_available_p(tty, 0)) {
- if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
+ if (done) {
retval = -EIO;
break;
}
poll_wait(file, &tty->read_wait, wait);
poll_wait(file, &tty->write_wait, wait);
+ if (check_other_done(tty))
+ mask |= POLLHUP;
if (input_available_p(tty, 1))
mask |= POLLIN | POLLRDNORM;
if (tty->packet && tty->link->ctrl_status)
mask |= POLLPRI | POLLIN | POLLRDNORM;
- if (test_bit(TTY_OTHER_CLOSED, &tty->flags))
- mask |= POLLHUP;
if (tty_hung_up_p(file))
mask |= POLLHUP;
if (!(mask & (POLLHUP | POLLIN | POLLRDNORM))) {
/* Review - krefs on tty_link ?? */
if (!tty->link)
return;
- tty_flush_to_ldisc(tty->link);
set_bit(TTY_OTHER_CLOSED, &tty->link->flags);
- wake_up_interruptible(&tty->link->read_wait);
+ tty_flip_buffer_push(tty->link->port);
wake_up_interruptible(&tty->link->write_wait);
if (tty->driver->subtype == PTY_TYPE_MASTER) {
set_bit(TTY_OTHER_CLOSED, &tty->flags);
goto out;
clear_bit(TTY_IO_ERROR, &tty->flags);
+ /* TTY_OTHER_CLOSED must be cleared before TTY_OTHER_DONE */
clear_bit(TTY_OTHER_CLOSED, &tty->link->flags);
+ clear_bit(TTY_OTHER_DONE, &tty->link->flags);
set_bit(TTY_THROTTLED, &tty->flags);
return 0;
writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
+ /* Assume that TX IRQ doesn't work until we see one: */
+ uap->tx_irq_seen = 0;
+
spin_lock_irq(&uap->port.lock);
/* restore RTS and DTR */
spin_lock_irq(&uap->port.lock);
uap->im = 0;
writew(uap->im, uap->port.membase + UART011_IMSC);
- writew(0xffff & ~UART011_TXIS, uap->port.membase + UART011_ICR);
+ writew(0xffff, uap->port.membase + UART011_ICR);
spin_unlock_irq(&uap->port.lock);
pl011_dma_shutdown(uap);
return 0;
err = setup_earlycon(buf);
- if (err == -ENOENT) {
- pr_warn("no match for %s\n", buf);
- err = 0;
- } else if (err == -EALREADY) {
- pr_warn("already registered\n");
- err = 0;
- }
+ if (err == -ENOENT || err == -EALREADY)
+ return 0;
return err;
}
early_param("earlycon", param_setup_earlycon);
err_add_port:
pm_runtime_put(&pdev->dev);
pm_runtime_disable(&pdev->dev);
+ pm_qos_remove_request(&up->pm_qos_request);
+ device_init_wakeup(up->dev, false);
err_rs485:
err_port_line:
return ret;
#define TTY_BUFFER_PAGE (((PAGE_SIZE - sizeof(struct tty_buffer)) / 2) & ~0xFF)
+/*
+ * If all tty flip buffers have been processed by flush_to_ldisc() or
+ * dropped by tty_buffer_flush(), check if the linked pty has been closed.
+ * If so, wake the reader/poll to process
+ */
+static inline void check_other_closed(struct tty_struct *tty)
+{
+ unsigned long flags, old;
+
+ /* transition from TTY_OTHER_CLOSED => TTY_OTHER_DONE must be atomic */
+ for (flags = ACCESS_ONCE(tty->flags);
+ test_bit(TTY_OTHER_CLOSED, &flags);
+ ) {
+ old = flags;
+ __set_bit(TTY_OTHER_DONE, &flags);
+ flags = cmpxchg(&tty->flags, old, flags);
+ if (old == flags) {
+ wake_up_interruptible(&tty->read_wait);
+ break;
+ }
+ }
+}
/**
* tty_buffer_lock_exclusive - gain exclusive access to buffer
if (ld && ld->ops->flush_buffer)
ld->ops->flush_buffer(tty);
+ check_other_closed(tty);
+
atomic_dec(&buf->priority);
mutex_unlock(&buf->lock);
}
smp_rmb();
count = head->commit - head->read;
if (!count) {
- if (next == NULL)
+ if (next == NULL) {
+ check_other_closed(tty);
break;
+ }
buf->head = next;
tty_buffer_free(port, head);
continue;
tty_ldisc_deref(disc);
}
-/**
- * tty_flush_to_ldisc
- * @tty: tty to push
- *
- * Push the terminal flip buffers to the line discipline.
- *
- * Must not be called from IRQ context.
- */
-void tty_flush_to_ldisc(struct tty_struct *tty)
-{
- flush_work(&tty->port->buf.work);
-}
-
/**
* tty_flip_buffer_push - terminal
* @port: tty port to push
char buf[32];
int ret;
- if (copy_from_user(buf, ubuf, min_t(size_t, sizeof(buf) - 1, count)))
+ count = min_t(size_t, sizeof(buf) - 1, count);
+ if (copy_from_user(buf, ubuf, count))
return -EFAULT;
+ /* sscanf requires a zero terminated string */
+ buf[count] = '\0';
+
if (sscanf(buf, "%u", &mode) != 1)
return -EINVAL;
{ USB_DEVICE(0x04f3, 0x010c), .driver_info =
USB_QUIRK_DEVICE_QUALIFIER },
+ { USB_DEVICE(0x04f3, 0x0125), .driver_info =
+ USB_QUIRK_DEVICE_QUALIFIER },
+
{ USB_DEVICE(0x04f3, 0x016f), .driver_info =
USB_QUIRK_DEVICE_QUALIFIER },
#define USBOTGSS_IRQENABLE_SET_MISC 0x003c
#define USBOTGSS_IRQENABLE_CLR_MISC 0x0040
#define USBOTGSS_IRQMISC_OFFSET 0x03fc
-#define USBOTGSS_UTMI_OTG_CTRL 0x0080
-#define USBOTGSS_UTMI_OTG_STATUS 0x0084
+#define USBOTGSS_UTMI_OTG_STATUS 0x0080
+#define USBOTGSS_UTMI_OTG_CTRL 0x0084
#define USBOTGSS_UTMI_OTG_OFFSET 0x0480
#define USBOTGSS_TXFIFO_DEPTH 0x0508
#define USBOTGSS_RXFIFO_DEPTH 0x050c
#define USBOTGSS_IRQMISC_DISCHRGVBUS_FALL (1 << 3)
#define USBOTGSS_IRQMISC_IDPULLUP_FALL (1 << 0)
-/* UTMI_OTG_CTRL REGISTER */
-#define USBOTGSS_UTMI_OTG_CTRL_DRVVBUS (1 << 5)
-#define USBOTGSS_UTMI_OTG_CTRL_CHRGVBUS (1 << 4)
-#define USBOTGSS_UTMI_OTG_CTRL_DISCHRGVBUS (1 << 3)
-#define USBOTGSS_UTMI_OTG_CTRL_IDPULLUP (1 << 0)
-
/* UTMI_OTG_STATUS REGISTER */
-#define USBOTGSS_UTMI_OTG_STATUS_SW_MODE (1 << 31)
-#define USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT (1 << 9)
-#define USBOTGSS_UTMI_OTG_STATUS_TXBITSTUFFENABLE (1 << 8)
-#define USBOTGSS_UTMI_OTG_STATUS_IDDIG (1 << 4)
-#define USBOTGSS_UTMI_OTG_STATUS_SESSEND (1 << 3)
-#define USBOTGSS_UTMI_OTG_STATUS_SESSVALID (1 << 2)
-#define USBOTGSS_UTMI_OTG_STATUS_VBUSVALID (1 << 1)
+#define USBOTGSS_UTMI_OTG_STATUS_DRVVBUS (1 << 5)
+#define USBOTGSS_UTMI_OTG_STATUS_CHRGVBUS (1 << 4)
+#define USBOTGSS_UTMI_OTG_STATUS_DISCHRGVBUS (1 << 3)
+#define USBOTGSS_UTMI_OTG_STATUS_IDPULLUP (1 << 0)
+
+/* UTMI_OTG_CTRL REGISTER */
+#define USBOTGSS_UTMI_OTG_CTRL_SW_MODE (1 << 31)
+#define USBOTGSS_UTMI_OTG_CTRL_POWERPRESENT (1 << 9)
+#define USBOTGSS_UTMI_OTG_CTRL_TXBITSTUFFENABLE (1 << 8)
+#define USBOTGSS_UTMI_OTG_CTRL_IDDIG (1 << 4)
+#define USBOTGSS_UTMI_OTG_CTRL_SESSEND (1 << 3)
+#define USBOTGSS_UTMI_OTG_CTRL_SESSVALID (1 << 2)
+#define USBOTGSS_UTMI_OTG_CTRL_VBUSVALID (1 << 1)
struct dwc3_omap {
struct device *dev;
int irq;
void __iomem *base;
- u32 utmi_otg_status;
+ u32 utmi_otg_ctrl;
u32 utmi_otg_offset;
u32 irqmisc_offset;
u32 irq_eoi_offset;
writel(value, base + offset);
}
-static u32 dwc3_omap_read_utmi_status(struct dwc3_omap *omap)
+static u32 dwc3_omap_read_utmi_ctrl(struct dwc3_omap *omap)
{
- return dwc3_omap_readl(omap->base, USBOTGSS_UTMI_OTG_STATUS +
+ return dwc3_omap_readl(omap->base, USBOTGSS_UTMI_OTG_CTRL +
omap->utmi_otg_offset);
}
-static void dwc3_omap_write_utmi_status(struct dwc3_omap *omap, u32 value)
+static void dwc3_omap_write_utmi_ctrl(struct dwc3_omap *omap, u32 value)
{
- dwc3_omap_writel(omap->base, USBOTGSS_UTMI_OTG_STATUS +
+ dwc3_omap_writel(omap->base, USBOTGSS_UTMI_OTG_CTRL +
omap->utmi_otg_offset, value);
}
}
}
- val = dwc3_omap_read_utmi_status(omap);
- val &= ~(USBOTGSS_UTMI_OTG_STATUS_IDDIG
- | USBOTGSS_UTMI_OTG_STATUS_VBUSVALID
- | USBOTGSS_UTMI_OTG_STATUS_SESSEND);
- val |= USBOTGSS_UTMI_OTG_STATUS_SESSVALID
- | USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT;
- dwc3_omap_write_utmi_status(omap, val);
+ val = dwc3_omap_read_utmi_ctrl(omap);
+ val &= ~(USBOTGSS_UTMI_OTG_CTRL_IDDIG
+ | USBOTGSS_UTMI_OTG_CTRL_VBUSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_SESSEND);
+ val |= USBOTGSS_UTMI_OTG_CTRL_SESSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_POWERPRESENT;
+ dwc3_omap_write_utmi_ctrl(omap, val);
break;
case OMAP_DWC3_VBUS_VALID:
dev_dbg(omap->dev, "VBUS Connect\n");
- val = dwc3_omap_read_utmi_status(omap);
- val &= ~USBOTGSS_UTMI_OTG_STATUS_SESSEND;
- val |= USBOTGSS_UTMI_OTG_STATUS_IDDIG
- | USBOTGSS_UTMI_OTG_STATUS_VBUSVALID
- | USBOTGSS_UTMI_OTG_STATUS_SESSVALID
- | USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT;
- dwc3_omap_write_utmi_status(omap, val);
+ val = dwc3_omap_read_utmi_ctrl(omap);
+ val &= ~USBOTGSS_UTMI_OTG_CTRL_SESSEND;
+ val |= USBOTGSS_UTMI_OTG_CTRL_IDDIG
+ | USBOTGSS_UTMI_OTG_CTRL_VBUSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_SESSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_POWERPRESENT;
+ dwc3_omap_write_utmi_ctrl(omap, val);
break;
case OMAP_DWC3_ID_FLOAT:
case OMAP_DWC3_VBUS_OFF:
dev_dbg(omap->dev, "VBUS Disconnect\n");
- val = dwc3_omap_read_utmi_status(omap);
- val &= ~(USBOTGSS_UTMI_OTG_STATUS_SESSVALID
- | USBOTGSS_UTMI_OTG_STATUS_VBUSVALID
- | USBOTGSS_UTMI_OTG_STATUS_POWERPRESENT);
- val |= USBOTGSS_UTMI_OTG_STATUS_SESSEND
- | USBOTGSS_UTMI_OTG_STATUS_IDDIG;
- dwc3_omap_write_utmi_status(omap, val);
+ val = dwc3_omap_read_utmi_ctrl(omap);
+ val &= ~(USBOTGSS_UTMI_OTG_CTRL_SESSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_VBUSVALID
+ | USBOTGSS_UTMI_OTG_CTRL_POWERPRESENT);
+ val |= USBOTGSS_UTMI_OTG_CTRL_SESSEND
+ | USBOTGSS_UTMI_OTG_CTRL_IDDIG;
+ dwc3_omap_write_utmi_ctrl(omap, val);
break;
default:
struct device_node *node = omap->dev->of_node;
int utmi_mode = 0;
- reg = dwc3_omap_read_utmi_status(omap);
+ reg = dwc3_omap_read_utmi_ctrl(omap);
of_property_read_u32(node, "utmi-mode", &utmi_mode);
switch (utmi_mode) {
case DWC3_OMAP_UTMI_MODE_SW:
- reg |= USBOTGSS_UTMI_OTG_STATUS_SW_MODE;
+ reg |= USBOTGSS_UTMI_OTG_CTRL_SW_MODE;
break;
case DWC3_OMAP_UTMI_MODE_HW:
- reg &= ~USBOTGSS_UTMI_OTG_STATUS_SW_MODE;
+ reg &= ~USBOTGSS_UTMI_OTG_CTRL_SW_MODE;
break;
default:
dev_dbg(omap->dev, "UNKNOWN utmi mode %d\n", utmi_mode);
}
- dwc3_omap_write_utmi_status(omap, reg);
+ dwc3_omap_write_utmi_ctrl(omap, reg);
}
static int dwc3_omap_extcon_register(struct dwc3_omap *omap)
{
struct dwc3_omap *omap = dev_get_drvdata(dev);
- omap->utmi_otg_status = dwc3_omap_read_utmi_status(omap);
+ omap->utmi_otg_ctrl = dwc3_omap_read_utmi_ctrl(omap);
dwc3_omap_disable_irqs(omap);
return 0;
{
struct dwc3_omap *omap = dev_get_drvdata(dev);
- dwc3_omap_write_utmi_status(omap, omap->utmi_otg_status);
+ dwc3_omap_write_utmi_ctrl(omap, omap->utmi_otg_ctrl);
dwc3_omap_enable_irqs(omap);
pm_runtime_disable(dev);
}
}
c->next_interface_id = 0;
+ memset(c->interface, 0, sizeof(c->interface));
c->superspeed = 0;
c->highspeed = 0;
c->fullspeed = 0;
| USB_REQ_GET_DESCRIPTOR):
switch (value >> 8) {
case HID_DT_HID:
+ {
+ struct hid_descriptor hidg_desc_copy = hidg_desc;
+
VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: HID\n");
+ hidg_desc_copy.desc[0].bDescriptorType = HID_DT_REPORT;
+ hidg_desc_copy.desc[0].wDescriptorLength =
+ cpu_to_le16(hidg->report_desc_length);
+
length = min_t(unsigned short, length,
- hidg_desc.bLength);
- memcpy(req->buf, &hidg_desc, length);
+ hidg_desc_copy.bLength);
+ memcpy(req->buf, &hidg_desc_copy, length);
goto respond;
break;
+ }
case HID_DT_REPORT:
VDBG(cdev, "USB_REQ_GET_DESCRIPTOR: REPORT\n");
length = min_t(unsigned short, length,
hidg_fs_in_ep_desc.wMaxPacketSize = cpu_to_le16(hidg->report_length);
hidg_hs_out_ep_desc.wMaxPacketSize = cpu_to_le16(hidg->report_length);
hidg_fs_out_ep_desc.wMaxPacketSize = cpu_to_le16(hidg->report_length);
+ /*
+ * We can use hidg_desc struct here but we should not relay
+ * that its content won't change after returning from this function.
+ */
hidg_desc.desc[0].bDescriptorType = HID_DT_REPORT;
hidg_desc.desc[0].wDescriptorLength =
cpu_to_le16(hidg->report_desc_length);
int write_allocated;
struct gs_buf port_write_buf;
wait_queue_head_t drain_wait; /* wait while writes drain */
+ bool write_busy;
/* REVISIT this state ... */
struct usb_cdc_line_coding port_line_coding; /* 8-N-1 etc */
int status = 0;
bool do_tty_wake = false;
- while (!list_empty(pool)) {
+ while (!port->write_busy && !list_empty(pool)) {
struct usb_request *req;
int len;
* NOTE that we may keep sending data for a while after
* the TTY closed (dev->ioport->port_tty is NULL).
*/
+ port->write_busy = true;
spin_unlock(&port->port_lock);
status = usb_ep_queue(in, req, GFP_ATOMIC);
spin_lock(&port->port_lock);
+ port->write_busy = false;
if (status) {
pr_debug("%s: %s %s err %d\n",
/*
* We _always_ have both ACM and mass storage functions.
*/
-static int __init acm_ms_do_config(struct usb_configuration *c)
+static int acm_ms_do_config(struct usb_configuration *c)
{
struct fsg_opts *opts;
int status;
/*-------------------------------------------------------------------------*/
-static int __init acm_ms_bind(struct usb_composite_dev *cdev)
+static int acm_ms_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
struct fsg_opts *opts;
return status;
}
-static int __exit acm_ms_unbind(struct usb_composite_dev *cdev)
+static int acm_ms_unbind(struct usb_composite_dev *cdev)
{
usb_put_function(f_msg);
usb_put_function_instance(fi_msg);
return 0;
}
-static __refdata struct usb_composite_driver acm_ms_driver = {
+static struct usb_composite_driver acm_ms_driver = {
.name = "g_acm_ms",
.dev = &device_desc,
.max_speed = USB_SPEED_SUPER,
.strings = dev_strings,
.bind = acm_ms_bind,
- .unbind = __exit_p(acm_ms_unbind),
+ .unbind = acm_ms_unbind,
};
module_usb_composite_driver(acm_ms_driver);
/*-------------------------------------------------------------------------*/
-static int __init audio_do_config(struct usb_configuration *c)
+static int audio_do_config(struct usb_configuration *c)
{
int status;
/*-------------------------------------------------------------------------*/
-static int __init audio_bind(struct usb_composite_dev *cdev)
+static int audio_bind(struct usb_composite_dev *cdev)
{
#ifndef CONFIG_GADGET_UAC1
struct f_uac2_opts *uac2_opts;
return status;
}
-static int __exit audio_unbind(struct usb_composite_dev *cdev)
+static int audio_unbind(struct usb_composite_dev *cdev)
{
#ifdef CONFIG_GADGET_UAC1
if (!IS_ERR_OR_NULL(f_uac1))
return 0;
}
-static __refdata struct usb_composite_driver audio_driver = {
+static struct usb_composite_driver audio_driver = {
.name = "g_audio",
.dev = &device_desc,
.strings = audio_strings,
.max_speed = USB_SPEED_HIGH,
.bind = audio_bind,
- .unbind = __exit_p(audio_unbind),
+ .unbind = audio_unbind,
};
module_usb_composite_driver(audio_driver);
/*
* We _always_ have both CDC ECM and CDC ACM functions.
*/
-static int __init cdc_do_config(struct usb_configuration *c)
+static int cdc_do_config(struct usb_configuration *c)
{
int status;
/*-------------------------------------------------------------------------*/
-static int __init cdc_bind(struct usb_composite_dev *cdev)
+static int cdc_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
struct f_ecm_opts *ecm_opts;
return status;
}
-static int __exit cdc_unbind(struct usb_composite_dev *cdev)
+static int cdc_unbind(struct usb_composite_dev *cdev)
{
usb_put_function(f_acm);
usb_put_function_instance(fi_serial);
return 0;
}
-static __refdata struct usb_composite_driver cdc_driver = {
+static struct usb_composite_driver cdc_driver = {
.name = "g_cdc",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = cdc_bind,
- .unbind = __exit_p(cdc_unbind),
+ .unbind = cdc_unbind,
};
module_usb_composite_driver(cdc_driver);
return -ENODEV;
}
-static int __init dbgp_bind(struct usb_gadget *gadget,
+static int dbgp_bind(struct usb_gadget *gadget,
struct usb_gadget_driver *driver)
{
int err, stp;
return err;
}
-static __refdata struct usb_gadget_driver dbgp_driver = {
+static struct usb_gadget_driver dbgp_driver = {
.function = "dbgp",
.max_speed = USB_SPEED_HIGH,
.bind = dbgp_bind,
* the first one present. That's to make Microsoft's drivers happy,
* and to follow DOCSIS 1.0 (cable modem standard).
*/
-static int __init rndis_do_config(struct usb_configuration *c)
+static int rndis_do_config(struct usb_configuration *c)
{
int status;
/*
* We _always_ have an ECM, CDC Subset, or EEM configuration.
*/
-static int __init eth_do_config(struct usb_configuration *c)
+static int eth_do_config(struct usb_configuration *c)
{
int status = 0;
/*-------------------------------------------------------------------------*/
-static int __init eth_bind(struct usb_composite_dev *cdev)
+static int eth_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
struct f_eem_opts *eem_opts = NULL;
return status;
}
-static int __exit eth_unbind(struct usb_composite_dev *cdev)
+static int eth_unbind(struct usb_composite_dev *cdev)
{
if (has_rndis()) {
usb_put_function(f_rndis);
return 0;
}
-static __refdata struct usb_composite_driver eth_driver = {
+static struct usb_composite_driver eth_driver = {
.name = "g_ether",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_SUPER,
.bind = eth_bind,
- .unbind = __exit_p(eth_unbind),
+ .unbind = eth_unbind,
};
module_usb_composite_driver(eth_driver);
static int gfs_do_config(struct usb_configuration *c);
-static __refdata struct usb_composite_driver gfs_driver = {
+static struct usb_composite_driver gfs_driver = {
.name = DRIVER_NAME,
.dev = &gfs_dev_desc,
.strings = gfs_dev_strings,
static struct usb_function_instance *fi_midi;
static struct usb_function *f_midi;
-static int __exit midi_unbind(struct usb_composite_dev *dev)
+static int midi_unbind(struct usb_composite_dev *dev)
{
usb_put_function(f_midi);
usb_put_function_instance(fi_midi);
.MaxPower = CONFIG_USB_GADGET_VBUS_DRAW,
};
-static int __init midi_bind_config(struct usb_configuration *c)
+static int midi_bind_config(struct usb_configuration *c)
{
int status;
return 0;
}
-static int __init midi_bind(struct usb_composite_dev *cdev)
+static int midi_bind(struct usb_composite_dev *cdev)
{
struct f_midi_opts *midi_opts;
int status;
return status;
}
-static __refdata struct usb_composite_driver midi_driver = {
+static struct usb_composite_driver midi_driver = {
.name = (char *) longname,
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = midi_bind,
- .unbind = __exit_p(midi_unbind),
+ .unbind = midi_unbind,
};
module_usb_composite_driver(midi_driver);
/****************************** Configurations ******************************/
-static int __init do_config(struct usb_configuration *c)
+static int do_config(struct usb_configuration *c)
{
struct hidg_func_node *e, *n;
int status = 0;
/****************************** Gadget Bind ******************************/
-static int __init hid_bind(struct usb_composite_dev *cdev)
+static int hid_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
struct list_head *tmp;
return status;
}
-static int __exit hid_unbind(struct usb_composite_dev *cdev)
+static int hid_unbind(struct usb_composite_dev *cdev)
{
struct hidg_func_node *n;
return 0;
}
-static int __init hidg_plat_driver_probe(struct platform_device *pdev)
+static int hidg_plat_driver_probe(struct platform_device *pdev)
{
struct hidg_func_descriptor *func = dev_get_platdata(&pdev->dev);
struct hidg_func_node *entry;
/****************************** Some noise ******************************/
-static __refdata struct usb_composite_driver hidg_driver = {
+static struct usb_composite_driver hidg_driver = {
.name = "g_hid",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = hid_bind,
- .unbind = __exit_p(hid_unbind),
+ .unbind = hid_unbind,
};
static struct platform_driver hidg_plat_driver = {
return 0;
}
-static int __init msg_do_config(struct usb_configuration *c)
+static int msg_do_config(struct usb_configuration *c)
{
struct fsg_opts *opts;
int ret;
/****************************** Gadget Bind ******************************/
-static int __init msg_bind(struct usb_composite_dev *cdev)
+static int msg_bind(struct usb_composite_dev *cdev)
{
static const struct fsg_operations ops = {
.thread_exits = msg_thread_exits,
/****************************** Some noise ******************************/
-static __refdata struct usb_composite_driver msg_driver = {
+static struct usb_composite_driver msg_driver = {
.name = "g_mass_storage",
.dev = &msg_device_desc,
.max_speed = USB_SPEED_SUPER,
static struct usb_function *f_rndis;
static struct usb_function *f_msg_rndis;
-static __init int rndis_do_config(struct usb_configuration *c)
+static int rndis_do_config(struct usb_configuration *c)
{
struct fsg_opts *fsg_opts;
int ret;
static struct usb_function *f_ecm;
static struct usb_function *f_msg_multi;
-static __init int cdc_do_config(struct usb_configuration *c)
+static int cdc_do_config(struct usb_configuration *c)
{
struct fsg_opts *fsg_opts;
int ret;
return status;
}
-static int __exit multi_unbind(struct usb_composite_dev *cdev)
+static int multi_unbind(struct usb_composite_dev *cdev)
{
#ifdef CONFIG_USB_G_MULTI_CDC
usb_put_function(f_msg_multi);
/****************************** Some noise ******************************/
-static __refdata struct usb_composite_driver multi_driver = {
+static struct usb_composite_driver multi_driver = {
.name = "g_multi",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = multi_bind,
- .unbind = __exit_p(multi_unbind),
+ .unbind = multi_unbind,
.needs_serial = 1,
};
/*-------------------------------------------------------------------------*/
-static int __init ncm_do_config(struct usb_configuration *c)
+static int ncm_do_config(struct usb_configuration *c)
{
int status;
/*-------------------------------------------------------------------------*/
-static int __init gncm_bind(struct usb_composite_dev *cdev)
+static int gncm_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
struct f_ncm_opts *ncm_opts;
return status;
}
-static int __exit gncm_unbind(struct usb_composite_dev *cdev)
+static int gncm_unbind(struct usb_composite_dev *cdev)
{
if (!IS_ERR_OR_NULL(f_ncm))
usb_put_function(f_ncm);
return 0;
}
-static __refdata struct usb_composite_driver ncm_driver = {
+static struct usb_composite_driver ncm_driver = {
.name = "g_ncm",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = gncm_bind,
- .unbind = __exit_p(gncm_unbind),
+ .unbind = gncm_unbind,
};
module_usb_composite_driver(ncm_driver);
static struct usb_function_instance *fi_obex2;
static struct usb_function_instance *fi_phonet;
-static int __init nokia_bind_config(struct usb_configuration *c)
+static int nokia_bind_config(struct usb_configuration *c)
{
struct usb_function *f_acm;
struct usb_function *f_phonet = NULL;
return status;
}
-static int __init nokia_bind(struct usb_composite_dev *cdev)
+static int nokia_bind(struct usb_composite_dev *cdev)
{
struct usb_gadget *gadget = cdev->gadget;
int status;
return status;
}
-static int __exit nokia_unbind(struct usb_composite_dev *cdev)
+static int nokia_unbind(struct usb_composite_dev *cdev)
{
if (!IS_ERR_OR_NULL(f_obex1_cfg2))
usb_put_function(f_obex1_cfg2);
return 0;
}
-static __refdata struct usb_composite_driver nokia_driver = {
+static struct usb_composite_driver nokia_driver = {
.name = "g_nokia",
.dev = &device_desc,
.strings = dev_strings,
.max_speed = USB_SPEED_HIGH,
.bind = nokia_bind,
- .unbind = __exit_p(nokia_unbind),
+ .unbind = nokia_unbind,
};
module_usb_composite_driver(nokia_driver);
.bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER,
};
-static int __init printer_do_config(struct usb_configuration *c)
+static int printer_do_config(struct usb_configuration *c)
{
struct usb_gadget *gadget = c->cdev->gadget;
int status = 0;
return status;
}
-static int __init printer_bind(struct usb_composite_dev *cdev)
+static int printer_bind(struct usb_composite_dev *cdev)
{
struct f_printer_opts *opts;
int ret, len;
return ret;
}
-static int __exit printer_unbind(struct usb_composite_dev *cdev)
+static int printer_unbind(struct usb_composite_dev *cdev)
{
usb_put_function(f_printer);
usb_put_function_instance(fi_printer);
return 0;
}
-static __refdata struct usb_composite_driver printer_driver = {
+static struct usb_composite_driver printer_driver = {
.name = shortname,
.dev = &device_desc,
.strings = dev_strings,
return ret;
}
-static int __init gs_bind(struct usb_composite_dev *cdev)
+static int gs_bind(struct usb_composite_dev *cdev)
{
int status;
return 0;
}
-static __refdata struct usb_composite_driver gserial_driver = {
+static struct usb_composite_driver gserial_driver = {
.name = "g_serial",
.dev = &device_desc,
.strings = dev_strings,
return 0;
}
-static __refdata struct usb_composite_driver usbg_driver = {
+static struct usb_composite_driver usbg_driver = {
.name = "g_target",
.dev = &usbg_device_desc,
.strings = usbg_strings,
* USB configuration
*/
-static int __init
+static int
webcam_config_bind(struct usb_configuration *c)
{
int status = 0;
.MaxPower = CONFIG_USB_GADGET_VBUS_DRAW,
};
-static int /* __init_or_exit */
+static int
webcam_unbind(struct usb_composite_dev *cdev)
{
if (!IS_ERR_OR_NULL(f_uvc))
return 0;
}
-static int __init
+static int
webcam_bind(struct usb_composite_dev *cdev)
{
struct f_uvc_opts *uvc_opts;
* Driver
*/
-static __refdata struct usb_composite_driver webcam_driver = {
+static struct usb_composite_driver webcam_driver = {
.name = "g_webcam",
.dev = &webcam_device_descriptor,
.strings = webcam_device_strings,
module_param_named(qlen, gzero_options.qlen, uint, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(qlen, "depth of loopback queue");
-static int __init zero_bind(struct usb_composite_dev *cdev)
+static int zero_bind(struct usb_composite_dev *cdev)
{
struct f_ss_opts *ss_opts;
struct f_lb_opts *lb_opts;
return 0;
}
-static __refdata struct usb_composite_driver zero_driver = {
+static struct usb_composite_driver zero_driver = {
.name = "zero",
.dev = &device_desc,
.strings = dev_strings,
return retval;
}
-static int __exit at91udc_remove(struct platform_device *pdev)
+static int at91udc_remove(struct platform_device *pdev)
{
struct at91_udc *udc = platform_get_drvdata(pdev);
unsigned long flags;
#endif
static struct platform_driver at91_udc_driver = {
- .remove = __exit_p(at91udc_remove),
+ .remove = at91udc_remove,
.shutdown = at91udc_shutdown,
.suspend = at91udc_suspend,
.resume = at91udc_resume,
return 0;
}
-static int __exit usba_udc_remove(struct platform_device *pdev)
+static int usba_udc_remove(struct platform_device *pdev)
{
struct usba_udc *udc;
int i;
static SIMPLE_DEV_PM_OPS(usba_udc_pm_ops, usba_udc_suspend, usba_udc_resume);
static struct platform_driver udc_driver = {
- .remove = __exit_p(usba_udc_remove),
+ .remove = usba_udc_remove,
.driver = {
.name = "atmel_usba_udc",
.pm = &usba_udc_pm_ops,
/* Driver removal function
* Free resources and finish pending transactions
*/
-static int __exit fsl_udc_remove(struct platform_device *pdev)
+static int fsl_udc_remove(struct platform_device *pdev)
{
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
struct fsl_usb2_platform_data *pdata = dev_get_platdata(&pdev->dev);
};
MODULE_DEVICE_TABLE(platform, fsl_udc_devtype);
static struct platform_driver udc_driver = {
- .remove = __exit_p(fsl_udc_remove),
+ .remove = fsl_udc_remove,
/* Just for FSL i.mx SoC currently */
.id_table = fsl_udc_devtype,
/* these suspend and resume are not usb suspend and resume */
.udc_stop = fusb300_udc_stop,
};
-static int __exit fusb300_remove(struct platform_device *pdev)
+static int fusb300_remove(struct platform_device *pdev)
{
struct fusb300 *fusb300 = platform_get_drvdata(pdev);
}
static struct platform_driver fusb300_driver = {
- .remove = __exit_p(fusb300_remove),
+ .remove = fusb300_remove,
.driver = {
.name = (char *) udc_name,
},
.pullup = m66592_pullup,
};
-static int __exit m66592_remove(struct platform_device *pdev)
+static int m66592_remove(struct platform_device *pdev)
{
struct m66592 *m66592 = platform_get_drvdata(pdev);
/*-------------------------------------------------------------------------*/
static struct platform_driver m66592_driver = {
- .remove = __exit_p(m66592_remove),
+ .remove = m66592_remove,
.driver = {
.name = (char *) udc_name,
},
.set_selfpowered = r8a66597_set_selfpowered,
};
-static int __exit r8a66597_remove(struct platform_device *pdev)
+static int r8a66597_remove(struct platform_device *pdev)
{
struct r8a66597 *r8a66597 = platform_get_drvdata(pdev);
/*-------------------------------------------------------------------------*/
static struct platform_driver r8a66597_driver = {
- .remove = __exit_p(r8a66597_remove),
+ .remove = r8a66597_remove,
.driver = {
.name = (char *) udc_name,
},
/* Map the registers */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
udc->addr = devm_ioremap_resource(&pdev->dev, res);
- if (!udc->addr)
- return -ENOMEM;
+ if (IS_ERR(udc->addr))
+ return PTR_ERR(udc->addr);
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
break;
case COMP_DEV_ERR:
case COMP_STALL:
+ frame->status = -EPROTO;
+ skip_td = true;
+ break;
case COMP_TX_ERR:
frame->status = -EPROTO;
+ if (event_trb != td->last_trb)
+ return 0;
skip_td = true;
break;
case COMP_STOP:
xhci_halt(xhci);
hw_died:
spin_unlock(&xhci->lock);
- return -ESHUTDOWN;
+ return IRQ_HANDLED;
}
/*
* since the command ring is 64-byte aligned.
* It must also be greater than 16.
*/
-#define TRBS_PER_SEGMENT 64
+#define TRBS_PER_SEGMENT 256
/* Allow two commands + a link TRB, along with any reserved command TRBs */
#define MAX_RSVD_CMD_TRBS (TRBS_PER_SEGMENT - 3)
#define TRB_SEGMENT_SIZE (TRBS_PER_SEGMENT*16)
#if defined(CONFIG_MACH_OMAP_H2) || defined(CONFIG_MACH_OMAP_H3)
-#if defined(CONFIG_TPS65010) || defined(CONFIG_TPS65010_MODULE)
+#if defined(CONFIG_TPS65010) || (defined(CONFIG_TPS65010_MODULE) && defined(MODULE))
#include <linux/i2c/tps65010.h>
{ USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
{ USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
{ USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
+ { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
{ USB_DEVICE(DCU10_VENDOR_ID, DCU10_PRODUCT_ID) },
{ USB_DEVICE(SITECOM_VENDOR_ID, SITECOM_PRODUCT_ID) },
{ USB_DEVICE(ALCATEL_VENDOR_ID, ALCATEL_PRODUCT_ID) },
- { USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_ID) },
{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_SX1),
.driver_info = PL2303_QUIRK_UART_STATE_IDX0 },
{ USB_DEVICE(SIEMENS_VENDOR_ID, SIEMENS_PRODUCT_ID_X65),
#define ALCATEL_VENDOR_ID 0x11f7
#define ALCATEL_PRODUCT_ID 0x02df
-/* Samsung I330 phone cradle */
-#define SAMSUNG_VENDOR_ID 0x04e8
-#define SAMSUNG_PRODUCT_ID 0x8001
-
#define SIEMENS_VENDOR_ID 0x11f5
#define SIEMENS_PRODUCT_ID_SX1 0x0001
#define SIEMENS_PRODUCT_ID_X65 0x0003
.driver_info = (kernel_ulong_t)&palm_os_4_probe },
{ USB_DEVICE(ACER_VENDOR_ID, ACER_S10_ID),
.driver_info = (kernel_ulong_t)&palm_os_4_probe },
- { USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_SCH_I330_ID),
+ { USB_DEVICE_INTERFACE_CLASS(SAMSUNG_VENDOR_ID, SAMSUNG_SCH_I330_ID, 0xff),
.driver_info = (kernel_ulong_t)&palm_os_4_probe },
{ USB_DEVICE(SAMSUNG_VENDOR_ID, SAMSUNG_SPH_I500_ID),
.driver_info = (kernel_ulong_t)&palm_os_4_probe },
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_GO_SLOW ),
+/* Reported by Christian Schaller <cschalle@redhat.com> */
+UNUSUAL_DEV( 0x059f, 0x0651, 0x0000, 0x0000,
+ "LaCie",
+ "External HDD",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_NO_WP_DETECT ),
+
/* Submitted by Joel Bourquard <numlock@freesurf.ch>
* Some versions of this device need the SubClass and Protocol overrides
* while others don't.
pb->pwm = devm_pwm_get(&pdev->dev, NULL);
if (IS_ERR(pb->pwm)) {
+ ret = PTR_ERR(pb->pwm);
+ if (ret == -EPROBE_DEFER)
+ goto err_alloc;
+
dev_err(&pdev->dev, "unable to request PWM, trying legacy API\n");
pb->legacy = true;
pb->pwm = pwm_request(data->pwm_id, "pwm-backlight");
}
EXPORT_SYMBOL_GPL(xen_evtchn_nr_channels);
-int bind_virq_to_irq(unsigned int virq, unsigned int cpu)
+int bind_virq_to_irq(unsigned int virq, unsigned int cpu, bool percpu)
{
struct evtchn_bind_virq bind_virq;
int evtchn, irq, ret;
if (irq < 0)
goto out;
- irq_set_chip_and_handler_name(irq, &xen_percpu_chip,
- handle_percpu_irq, "virq");
+ if (percpu)
+ irq_set_chip_and_handler_name(irq, &xen_percpu_chip,
+ handle_percpu_irq, "virq");
+ else
+ irq_set_chip_and_handler_name(irq, &xen_dynamic_chip,
+ handle_edge_irq, "virq");
bind_virq.virq = virq;
bind_virq.vcpu = cpu;
{
int irq, retval;
- irq = bind_virq_to_irq(virq, cpu);
+ irq = bind_virq_to_irq(virq, cpu, irqflags & IRQF_PERCPU);
if (irq < 0)
return irq;
retval = request_irq(irq, handler, irqflags, devname, dev_id);
* indirect refs to their parent bytenr.
* When roots are found, they're added to the roots list
*
+ * NOTE: This can return values > 0
+ *
* FIXME some caching might speed things up
*/
static int find_parent_nodes(struct btrfs_trans_handle *trans,
return ret;
}
+/**
+ * btrfs_check_shared - tell us whether an extent is shared
+ *
+ * @trans: optional trans handle
+ *
+ * btrfs_check_shared uses the backref walking code but will short
+ * circuit as soon as it finds a root or inode that doesn't match the
+ * one passed in. This provides a significant performance benefit for
+ * callers (such as fiemap) which want to know whether the extent is
+ * shared but do not need a ref count.
+ *
+ * Return: 0 if extent is not shared, 1 if it is shared, < 0 on error.
+ */
int btrfs_check_shared(struct btrfs_trans_handle *trans,
struct btrfs_fs_info *fs_info, u64 root_objectid,
u64 inum, u64 bytenr)
ret = find_parent_nodes(trans, fs_info, bytenr, elem.seq, tmp,
roots, NULL, root_objectid, inum);
if (ret == BACKREF_FOUND_SHARED) {
+ /* this is the only condition under which we return 1 */
ret = 1;
break;
}
if (ret < 0 && ret != -ENOENT)
break;
+ ret = 0;
node = ulist_next(tmp, &uiter);
if (!node)
break;
btrfs_mark_buffer_dirty(leaf);
fail:
btrfs_release_path(path);
- if (ret)
- btrfs_abort_transaction(trans, root, ret);
return ret;
}
ret = 0;
}
}
- if (!ret)
+ if (!ret) {
ret = write_one_cache_group(trans, root, path, cache);
+ /*
+ * Our block group might still be attached to the list
+ * of new block groups in the transaction handle of some
+ * other task (struct btrfs_trans_handle->new_bgs). This
+ * means its block group item isn't yet in the extent
+ * tree. If this happens ignore the error, as we will
+ * try again later in the critical section of the
+ * transaction commit.
+ */
+ if (ret == -ENOENT) {
+ ret = 0;
+ spin_lock(&cur_trans->dirty_bgs_lock);
+ if (list_empty(&cache->dirty_list)) {
+ list_add_tail(&cache->dirty_list,
+ &cur_trans->dirty_bgs);
+ btrfs_get_block_group(cache);
+ }
+ spin_unlock(&cur_trans->dirty_bgs_lock);
+ } else if (ret) {
+ btrfs_abort_transaction(trans, root, ret);
+ }
+ }
/* if its not on the io list, we need to put the block group */
if (should_put)
ret = 0;
}
}
- if (!ret)
+ if (!ret) {
ret = write_one_cache_group(trans, root, path, cache);
+ if (ret)
+ btrfs_abort_transaction(trans, root, ret);
+ }
/* if its not on the io list, we need to put the block group */
if (should_put)
goto again;
}
+ /*
+ * if we are changing raid levels, try to allocate a corresponding
+ * block group with the new raid level.
+ */
+ alloc_flags = update_block_group_flags(root, cache->flags);
+ if (alloc_flags != cache->flags) {
+ ret = do_chunk_alloc(trans, root, alloc_flags,
+ CHUNK_ALLOC_FORCE);
+ /*
+ * ENOSPC is allowed here, we may have enough space
+ * already allocated at the new raid level to
+ * carry on
+ */
+ if (ret == -ENOSPC)
+ ret = 0;
+ if (ret < 0)
+ goto out;
+ }
ret = set_block_group_ro(cache, 0);
if (!ret)
out:
if (cache->flags & BTRFS_BLOCK_GROUP_SYSTEM) {
alloc_flags = update_block_group_flags(root, cache->flags);
+ lock_chunks(root->fs_info->chunk_root);
check_system_chunk(trans, root, alloc_flags);
+ unlock_chunks(root->fs_info->chunk_root);
}
mutex_unlock(&root->fs_info->ro_block_group_mutex);
start >> PAGE_CACHE_SHIFT);
if (eb && atomic_inc_not_zero(&eb->refs)) {
rcu_read_unlock();
+ /*
+ * Lock our eb's refs_lock to avoid races with
+ * free_extent_buffer. When we get our eb it might be flagged
+ * with EXTENT_BUFFER_STALE and another task running
+ * free_extent_buffer might have seen that flag set,
+ * eb->refs == 2, that the buffer isn't under IO (dirty and
+ * writeback flags not set) and it's still in the tree (flag
+ * EXTENT_BUFFER_TREE_REF set), therefore being in the process
+ * of decrementing the extent buffer's reference count twice.
+ * So here we could race and increment the eb's reference count,
+ * clear its stale flag, mark it as dirty and drop our reference
+ * before the other task finishes executing free_extent_buffer,
+ * which would later result in an attempt to free an extent
+ * buffer that is dirty.
+ */
+ if (test_bit(EXTENT_BUFFER_STALE, &eb->bflags)) {
+ spin_lock(&eb->refs_lock);
+ spin_unlock(&eb->refs_lock);
+ }
mark_extent_buffer_accessed(eb, NULL);
return eb;
}
struct btrfs_free_space_ctl *ctl = root->free_ino_ctl;
int ret;
struct btrfs_io_ctl io_ctl;
+ bool release_metadata = true;
if (!btrfs_test_opt(root, INODE_MAP_CACHE))
return 0;
memset(&io_ctl, 0, sizeof(io_ctl));
ret = __btrfs_write_out_cache(root, inode, ctl, NULL, &io_ctl,
trans, path, 0);
- if (!ret)
+ if (!ret) {
+ /*
+ * At this point writepages() didn't error out, so our metadata
+ * reservation is released when the writeback finishes, at
+ * inode.c:btrfs_finish_ordered_io(), regardless of it finishing
+ * with or without an error.
+ */
+ release_metadata = false;
ret = btrfs_wait_cache_io(root, trans, NULL, &io_ctl, path, 0);
+ }
if (ret) {
- btrfs_delalloc_release_metadata(inode, inode->i_size);
+ if (release_metadata)
+ btrfs_delalloc_release_metadata(inode, inode->i_size);
#ifdef DEBUG
btrfs_err(root->fs_info,
"failed to write free ino cache for root %llu",
int btrfs_wait_ordered_range(struct inode *inode, u64 start, u64 len)
{
int ret = 0;
+ int ret_wb = 0;
u64 end;
u64 orig_end;
struct btrfs_ordered_extent *ordered;
if (ret)
return ret;
- ret = filemap_fdatawait_range(inode->i_mapping, start, orig_end);
- if (ret)
- return ret;
+ /*
+ * If we have a writeback error don't return immediately. Wait first
+ * for any ordered extents that haven't completed yet. This is to make
+ * sure no one can dirty the same page ranges and call writepages()
+ * before the ordered extents complete - to avoid failures (-EEXIST)
+ * when adding the new ordered extents to the ordered tree.
+ */
+ ret_wb = filemap_fdatawait_range(inode->i_mapping, start, orig_end);
end = orig_end;
while (1) {
break;
end--;
}
- return ret;
+ return ret_wb ? ret_wb : ret;
}
/*
{
u64 chunk_offset;
+ ASSERT(mutex_is_locked(&extent_root->fs_info->chunk_mutex));
chunk_offset = find_next_chunk(extent_root->fs_info);
return __btrfs_alloc_chunk(trans, extent_root, chunk_offset, type);
}
#include "cifsfs.h"
#include "dns_resolve.h"
#include "cifs_debug.h"
+#include "cifs_unicode.h"
static LIST_HEAD(cifs_dfs_automount_list);
xid = get_xid();
rc = get_dfs_path(xid, ses, full_path + 1, cifs_sb->local_nls,
&num_referrals, &referrals,
- cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR);
+ cifs_remap(cifs_sb));
free_xid(xid);
cifs_put_tlink(tlink);
#include "cifsglob.h"
#include "cifs_debug.h"
-/*
- * cifs_utf16_bytes - how long will a string be after conversion?
- * @utf16 - pointer to input string
- * @maxbytes - don't go past this many bytes of input string
- * @codepage - destination codepage
- *
- * Walk a utf16le string and return the number of bytes that the string will
- * be after being converted to the given charset, not including any null
- * termination required. Don't walk past maxbytes in the source buffer.
- */
-int
-cifs_utf16_bytes(const __le16 *from, int maxbytes,
- const struct nls_table *codepage)
-{
- int i;
- int charlen, outlen = 0;
- int maxwords = maxbytes / 2;
- char tmp[NLS_MAX_CHARSET_SIZE];
- __u16 ftmp;
-
- for (i = 0; i < maxwords; i++) {
- ftmp = get_unaligned_le16(&from[i]);
- if (ftmp == 0)
- break;
-
- charlen = codepage->uni2char(ftmp, tmp, NLS_MAX_CHARSET_SIZE);
- if (charlen > 0)
- outlen += charlen;
- else
- outlen++;
- }
-
- return outlen;
-}
-
int cifs_remap(struct cifs_sb_info *cifs_sb)
{
int map_type;
* enough to hold the result of the conversion (at least NLS_MAX_CHARSET_SIZE).
*/
static int
-cifs_mapchar(char *target, const __u16 src_char, const struct nls_table *cp,
+cifs_mapchar(char *target, const __u16 *from, const struct nls_table *cp,
int maptype)
{
int len = 1;
+ __u16 src_char;
+
+ src_char = *from;
if ((maptype == SFM_MAP_UNI_RSVD) && convert_sfm_char(src_char, target))
return len;
/* if character not one of seven in special remap set */
len = cp->uni2char(src_char, target, NLS_MAX_CHARSET_SIZE);
- if (len <= 0) {
- *target = '?';
- len = 1;
- }
+ if (len <= 0)
+ goto surrogate_pair;
+
+ return len;
+
+surrogate_pair:
+ /* convert SURROGATE_PAIR and IVS */
+ if (strcmp(cp->charset, "utf8"))
+ goto unknown;
+ len = utf16s_to_utf8s(from, 3, UTF16_LITTLE_ENDIAN, target, 6);
+ if (len <= 0)
+ goto unknown;
+ return len;
+
+unknown:
+ *target = '?';
+ len = 1;
return len;
}
int nullsize = nls_nullsize(codepage);
int fromwords = fromlen / 2;
char tmp[NLS_MAX_CHARSET_SIZE];
- __u16 ftmp;
+ __u16 ftmp[3]; /* ftmp[3] = 3array x 2bytes = 6bytes UTF-16 */
/*
* because the chars can be of varying widths, we need to take care
safelen = tolen - (NLS_MAX_CHARSET_SIZE + nullsize);
for (i = 0; i < fromwords; i++) {
- ftmp = get_unaligned_le16(&from[i]);
- if (ftmp == 0)
+ ftmp[0] = get_unaligned_le16(&from[i]);
+ if (ftmp[0] == 0)
break;
+ if (i + 1 < fromwords)
+ ftmp[1] = get_unaligned_le16(&from[i + 1]);
+ else
+ ftmp[1] = 0;
+ if (i + 2 < fromwords)
+ ftmp[2] = get_unaligned_le16(&from[i + 2]);
+ else
+ ftmp[2] = 0;
/*
* check to see if converting this character might make the
/* put converted char into 'to' buffer */
charlen = cifs_mapchar(&to[outlen], ftmp, codepage, map_type);
outlen += charlen;
+
+ /* charlen (=bytes of UTF-8 for 1 character)
+ * 4bytes UTF-8(surrogate pair) is charlen=4
+ * (4bytes UTF-16 code)
+ * 7-8bytes UTF-8(IVS) is charlen=3+4 or 4+4
+ * (2 UTF-8 pairs divided to 2 UTF-16 pairs) */
+ if (charlen == 4)
+ i++;
+ else if (charlen >= 5)
+ /* 5-6bytes UTF-8 */
+ i += 2;
}
/* properly null-terminate string */
return i;
}
+/*
+ * cifs_utf16_bytes - how long will a string be after conversion?
+ * @utf16 - pointer to input string
+ * @maxbytes - don't go past this many bytes of input string
+ * @codepage - destination codepage
+ *
+ * Walk a utf16le string and return the number of bytes that the string will
+ * be after being converted to the given charset, not including any null
+ * termination required. Don't walk past maxbytes in the source buffer.
+ */
+int
+cifs_utf16_bytes(const __le16 *from, int maxbytes,
+ const struct nls_table *codepage)
+{
+ int i;
+ int charlen, outlen = 0;
+ int maxwords = maxbytes / 2;
+ char tmp[NLS_MAX_CHARSET_SIZE];
+ __u16 ftmp[3];
+
+ for (i = 0; i < maxwords; i++) {
+ ftmp[0] = get_unaligned_le16(&from[i]);
+ if (ftmp[0] == 0)
+ break;
+ if (i + 1 < maxwords)
+ ftmp[1] = get_unaligned_le16(&from[i + 1]);
+ else
+ ftmp[1] = 0;
+ if (i + 2 < maxwords)
+ ftmp[2] = get_unaligned_le16(&from[i + 2]);
+ else
+ ftmp[2] = 0;
+
+ charlen = cifs_mapchar(tmp, ftmp, codepage, NO_MAP_UNI_RSVD);
+ outlen += charlen;
+ }
+
+ return outlen;
+}
+
/*
* cifs_strndup_from_utf16 - copy a string from wire format to the local
* codepage
char src_char;
__le16 dst_char;
wchar_t tmp;
+ wchar_t *wchar_to; /* UTF-16 */
+ int ret;
+ unicode_t u;
if (map_chars == NO_MAP_UNI_RSVD)
return cifs_strtoUTF16(target, source, PATH_MAX, cp);
+ wchar_to = kzalloc(6, GFP_KERNEL);
+
for (i = 0; i < srclen; j++) {
src_char = source[i];
charlen = 1;
* if no match, use question mark, which at least in
* some cases serves as wild card
*/
- if (charlen < 1) {
- dst_char = cpu_to_le16(0x003f);
- charlen = 1;
+ if (charlen > 0)
+ goto ctoUTF16;
+
+ /* convert SURROGATE_PAIR */
+ if (strcmp(cp->charset, "utf8") || !wchar_to)
+ goto unknown;
+ if (*(source + i) & 0x80) {
+ charlen = utf8_to_utf32(source + i, 6, &u);
+ if (charlen < 0)
+ goto unknown;
+ } else
+ goto unknown;
+ ret = utf8s_to_utf16s(source + i, charlen,
+ UTF16_LITTLE_ENDIAN,
+ wchar_to, 6);
+ if (ret < 0)
+ goto unknown;
+
+ i += charlen;
+ dst_char = cpu_to_le16(*wchar_to);
+ if (charlen <= 3)
+ /* 1-3bytes UTF-8 to 2bytes UTF-16 */
+ put_unaligned(dst_char, &target[j]);
+ else if (charlen == 4) {
+ /* 4bytes UTF-8(surrogate pair) to 4bytes UTF-16
+ * 7-8bytes UTF-8(IVS) divided to 2 UTF-16
+ * (charlen=3+4 or 4+4) */
+ put_unaligned(dst_char, &target[j]);
+ dst_char = cpu_to_le16(*(wchar_to + 1));
+ j++;
+ put_unaligned(dst_char, &target[j]);
+ } else if (charlen >= 5) {
+ /* 5-6bytes UTF-8 to 6bytes UTF-16 */
+ put_unaligned(dst_char, &target[j]);
+ dst_char = cpu_to_le16(*(wchar_to + 1));
+ j++;
+ put_unaligned(dst_char, &target[j]);
+ dst_char = cpu_to_le16(*(wchar_to + 2));
+ j++;
+ put_unaligned(dst_char, &target[j]);
}
+ continue;
+
+unknown:
+ dst_char = cpu_to_le16(0x003f);
+ charlen = 1;
}
+
+ctoUTF16:
/*
* character may take more than one byte in the source string,
* but will take exactly two bytes in the target string
ctoUTF16_out:
put_unaligned(0, &target[j]); /* Null terminate target unicode string */
+ kfree(wchar_to);
return j;
}
seq_puts(s, ",nouser_xattr");
if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SPECIAL_CHR)
seq_puts(s, ",mapchars");
+ if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_MAP_SFM_CHR)
+ seq_puts(s, ",mapposix");
if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_UNX_EMUL)
seq_puts(s, ",sfu");
if (cifs_sb->mnt_cifs_flags & CIFS_MOUNT_NO_BRL)
extern int CIFSUnixCreateSymLink(const unsigned int xid,
struct cifs_tcon *tcon,
const char *fromName, const char *toName,
- const struct nls_table *nls_codepage);
+ const struct nls_table *nls_codepage, int remap);
extern int CIFSSMBUnixQuerySymLink(const unsigned int xid,
struct cifs_tcon *tcon,
const unsigned char *searchName, char **syminfo,
- const struct nls_table *nls_codepage);
+ const struct nls_table *nls_codepage, int remap);
extern int CIFSSMBQuerySymLink(const unsigned int xid, struct cifs_tcon *tcon,
__u16 fid, char **symlinkinfo,
const struct nls_table *nls_codepage);
int
CIFSUnixCreateSymLink(const unsigned int xid, struct cifs_tcon *tcon,
const char *fromName, const char *toName,
- const struct nls_table *nls_codepage)
+ const struct nls_table *nls_codepage, int remap)
{
TRANSACTION2_SPI_REQ *pSMB = NULL;
TRANSACTION2_SPI_RSP *pSMBr = NULL;
if (pSMB->hdr.Flags2 & SMBFLG2_UNICODE) {
name_len =
- cifs_strtoUTF16((__le16 *) pSMB->FileName, fromName,
- /* find define for this maxpathcomponent */
- PATH_MAX, nls_codepage);
+ cifsConvertToUTF16((__le16 *) pSMB->FileName, fromName,
+ /* find define for this maxpathcomponent */
+ PATH_MAX, nls_codepage, remap);
name_len++; /* trailing null */
name_len *= 2;
data_offset = (char *) (&pSMB->hdr.Protocol) + offset;
if (pSMB->hdr.Flags2 & SMBFLG2_UNICODE) {
name_len_target =
- cifs_strtoUTF16((__le16 *) data_offset, toName, PATH_MAX
- /* find define for this maxpathcomponent */
- , nls_codepage);
+ cifsConvertToUTF16((__le16 *) data_offset, toName,
+ /* find define for this maxpathcomponent */
+ PATH_MAX, nls_codepage, remap);
name_len_target++; /* trailing null */
name_len_target *= 2;
} else { /* BB improve the check for buffer overruns BB */
int
CIFSSMBUnixQuerySymLink(const unsigned int xid, struct cifs_tcon *tcon,
const unsigned char *searchName, char **symlinkinfo,
- const struct nls_table *nls_codepage)
+ const struct nls_table *nls_codepage, int remap)
{
/* SMB_QUERY_FILE_UNIX_LINK */
TRANSACTION2_QPI_REQ *pSMB = NULL;
if (pSMB->hdr.Flags2 & SMBFLG2_UNICODE) {
name_len =
- cifs_strtoUTF16((__le16 *) pSMB->FileName, searchName,
- PATH_MAX, nls_codepage);
+ cifsConvertToUTF16((__le16 *) pSMB->FileName,
+ searchName, PATH_MAX, nls_codepage,
+ remap);
name_len++; /* trailing null */
name_len *= 2;
} else { /* BB improve the check for buffer overruns BB */
strncpy(pSMB->RequestFileName, search_name, name_len);
}
- if (ses->server && ses->server->sign)
+ if (ses->server->sign)
pSMB->hdr.Flags2 |= SMBFLG2_SECURITY_SIGNATURE;
pSMB->hdr.Uid = ses->Suid;
rc = generic_ip_connect(server);
if (rc) {
cifs_dbg(FYI, "reconnect error %d\n", rc);
+ mutex_unlock(&server->srv_mutex);
msleep(3000);
} else {
atomic_inc(&tcpSesReconnectCount);
if (server->tcpStatus != CifsExiting)
server->tcpStatus = CifsNeedNegotiate;
spin_unlock(&GlobalMid_Lock);
+ mutex_unlock(&server->srv_mutex);
}
- mutex_unlock(&server->srv_mutex);
} while (server->tcpStatus == CifsNeedReconnect);
return rc;
}
rc = CIFSSMBUnixSetPathInfo(xid, tcon, full_path, &args,
cifs_sb->local_nls,
- cifs_sb->mnt_cifs_flags &
- CIFS_MOUNT_MAP_SPECIAL_CHR);
+ cifs_remap(cifs_sb));
if (rc)
goto mknod_out;
posix_flags = cifs_posix_convert_flags(f_flags);
rc = CIFSPOSIXCreate(xid, tcon, posix_flags, mode, pnetfid, presp_data,
poplock, full_path, cifs_sb->local_nls,
- cifs_sb->mnt_cifs_flags &
- CIFS_MOUNT_MAP_SPECIAL_CHR);
+ cifs_remap(cifs_sb));
cifs_put_tlink(tlink);
if (rc)
rc = server->ops->mand_unlock_range(cfile, flock, xid);
out:
- if (flock->fl_flags & FL_POSIX)
- posix_lock_file_wait(file, flock);
+ if (flock->fl_flags & FL_POSIX && !rc)
+ rc = posix_lock_file_wait(file, flock);
return rc;
}
/* could have done a find first instead but this returns more info */
rc = CIFSSMBUnixQPathInfo(xid, tcon, full_path, &find_data,
- cifs_sb->local_nls, cifs_sb->mnt_cifs_flags &
- CIFS_MOUNT_MAP_SPECIAL_CHR);
+ cifs_sb->local_nls, cifs_remap(cifs_sb));
cifs_put_tlink(tlink);
if (!rc) {
rc = -ENOMEM;
} else {
/* we already have inode, update it */
+
+ /* if uniqueid is different, return error */
+ if (unlikely(cifs_sb->mnt_cifs_flags & CIFS_MOUNT_SERVER_INUM &&
+ CIFS_I(*pinode)->uniqueid != fattr.cf_uniqueid)) {
+ rc = -ESTALE;
+ goto cgiiu_exit;
+ }
+
+ /* if filetype is different, return error */
+ if (unlikely(((*pinode)->i_mode & S_IFMT) !=
+ (fattr.cf_mode & S_IFMT))) {
+ rc = -ESTALE;
+ goto cgiiu_exit;
+ }
+
cifs_fattr_to_inode(*pinode, &fattr);
}
+cgiiu_exit:
return rc;
}
if (!*inode)
rc = -ENOMEM;
} else {
+ /* we already have inode, update it */
+
+ /* if filetype is different, return error */
+ if (unlikely(((*inode)->i_mode & S_IFMT) !=
+ (fattr.cf_mode & S_IFMT))) {
+ rc = -ESTALE;
+ goto cgii_exit;
+ }
+
cifs_fattr_to_inode(*inode, &fattr);
}
pTcon = tlink_tcon(tlink);
rc = CIFSSMBUnixSetPathInfo(xid, pTcon, full_path, args,
cifs_sb->local_nls,
- cifs_sb->mnt_cifs_flags &
- CIFS_MOUNT_MAP_SPECIAL_CHR);
+ cifs_remap(cifs_sb));
cifs_put_tlink(tlink);
}
rc = create_mf_symlink(xid, pTcon, cifs_sb, full_path, symname);
else if (pTcon->unix_ext)
rc = CIFSUnixCreateSymLink(xid, pTcon, full_path, symname,
- cifs_sb->local_nls);
+ cifs_sb->local_nls,
+ cifs_remap(cifs_sb));
/* else
rc = CIFSCreateReparseSymLink(xid, pTcon, fromName, toName,
cifs_sb_target->local_nls); */
if (dentry) {
inode = d_inode(dentry);
if (inode) {
+ if (d_mountpoint(dentry))
+ goto out;
/*
* If we're generating inode numbers, then we don't
* want to clobber the existing one with the one that
/* Check for unix extensions */
if (cap_unix(tcon->ses)) {
rc = CIFSSMBUnixQuerySymLink(xid, tcon, full_path, target_path,
- cifs_sb->local_nls);
+ cifs_sb->local_nls,
+ cifs_remap(cifs_sb));
if (rc == -EREMOTE)
rc = cifs_unix_dfs_readlink(xid, tcon, full_path,
target_path,
/* GLOBAL_CAP_LARGE_MTU will only be set if dialect > SMB2.02 */
/* See sections 2.2.4 and 3.2.4.1.5 of MS-SMB2 */
- if ((tcon->ses) &&
+ if ((tcon->ses) && (tcon->ses->server) &&
(tcon->ses->server->capabilities & SMB2_GLOBAL_CAP_LARGE_MTU))
hdr->CreditCharge = cpu_to_le16(1);
/* else CreditCharge MBZ */
if (stack_base > STACK_SIZE_MAX)
stack_base = STACK_SIZE_MAX;
+ /* Add space for stack randomization. */
+ stack_base += (STACK_RND_MASK << PAGE_SHIFT);
+
/* Make sure we didn't let the argument array grow too large. */
if (vma->vm_end - vma->vm_start > stack_base)
return -ENOMEM;
struct ext4_map_blocks *map, int flags);
extern int ext4_ext_calc_metadata_amount(struct inode *inode,
ext4_lblk_t lblocks);
-extern int ext4_extent_tree_init(handle_t *, struct inode *);
extern int ext4_ext_calc_credits_for_single_extent(struct inode *inode,
int num,
struct ext4_ext_path *path);
ext4_put_nojournal(handle);
return 0;
}
+
+ if (!handle->h_transaction) {
+ err = jbd2_journal_stop(handle);
+ return handle->h_err ? handle->h_err : err;
+ }
+
sb = handle->h_transaction->t_journal->j_private;
err = handle->h_err;
rc = jbd2_journal_stop(handle);
ext4_lblk_t lblock = le32_to_cpu(ext->ee_block);
ext4_lblk_t last = lblock + len - 1;
- if (lblock > last)
+ if (len == 0 || lblock > last)
return 0;
return ext4_data_block_valid(EXT4_SB(inode->i_sb), block, len);
}
loff_t new_size, ioffset;
int ret;
+ /*
+ * We need to test this early because xfstests assumes that a
+ * collapse range of (0, 1) will return EOPNOTSUPP if the file
+ * system does not support collapse range.
+ */
+ if (!ext4_test_inode_flag(inode, EXT4_INODE_EXTENTS))
+ return -EOPNOTSUPP;
+
/* Collapse range works only on fs block size aligned offsets. */
if (offset & (EXT4_CLUSTER_SIZE(sb) - 1) ||
len & (EXT4_CLUSTER_SIZE(sb) - 1))
int inode_size = EXT4_INODE_SIZE(sb);
oi.orig_ino = orig_ino;
- ino = orig_ino & ~(inodes_per_block - 1);
+ ino = (orig_ino & ~(inodes_per_block - 1)) + 1;
for (i = 0; i < inodes_per_block; i++, ino++, buf += inode_size) {
if (ino == orig_ino)
continue;
struct ext4_super_block *es = EXT4_SB(sb)->s_es;
EXT4_SB(sb)->s_mount_state |= EXT4_ERROR_FS;
+ if (bdev_read_only(sb->s_bdev))
+ return;
es->s_state |= cpu_to_le16(EXT4_ERROR_FS);
es->s_last_error_time = cpu_to_le32(get_seconds());
strncpy(es->s_last_error_func, func, sizeof(es->s_last_error_func));
if (name == NULL)
goto out_put;
- fd = file_create(name, mode & S_IFMT);
+ fd = file_create(name, mode & 0777);
if (fd < 0)
error = fd;
else
{
jbd2_journal_revoke_header_t *header;
int offset, max;
+ int csum_size = 0;
+ __u32 rcount;
int record_len = 4;
header = (jbd2_journal_revoke_header_t *) bh->b_data;
offset = sizeof(jbd2_journal_revoke_header_t);
- max = be32_to_cpu(header->r_count);
+ rcount = be32_to_cpu(header->r_count);
if (!jbd2_revoke_block_csum_verify(journal, header))
return -EINVAL;
+ if (jbd2_journal_has_csum_v2or3(journal))
+ csum_size = sizeof(struct jbd2_journal_revoke_tail);
+ if (rcount > journal->j_blocksize - csum_size)
+ return -EINVAL;
+ max = rcount;
+
if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
record_len = 8;
{
int csum_size = 0;
struct buffer_head *descriptor;
- int offset;
+ int sz, offset;
journal_header_t *header;
/* If we are already aborting, this all becomes a noop. We
if (jbd2_journal_has_csum_v2or3(journal))
csum_size = sizeof(struct jbd2_journal_revoke_tail);
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
+ sz = 8;
+ else
+ sz = 4;
+
/* Make sure we have a descriptor with space left for the record */
if (descriptor) {
- if (offset >= journal->j_blocksize - csum_size) {
+ if (offset + sz > journal->j_blocksize - csum_size) {
flush_descriptor(journal, descriptor, offset, write_op);
descriptor = NULL;
}
*descriptorp = descriptor;
}
- if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT)) {
+ if (JBD2_HAS_INCOMPAT_FEATURE(journal, JBD2_FEATURE_INCOMPAT_64BIT))
* ((__be64 *)(&descriptor->b_data[offset])) =
cpu_to_be64(record->blocknr);
- offset += 8;
-
- } else {
+ else
* ((__be32 *)(&descriptor->b_data[offset])) =
cpu_to_be32(record->blocknr);
- offset += 4;
- }
+ offset += sz;
*offsetp = offset;
}
int result;
int wanted;
- WARN_ON(!transaction);
if (is_handle_aborted(handle))
return -EROFS;
journal = transaction->t_journal;
tid_t tid;
int need_to_start, ret;
- WARN_ON(!transaction);
/* If we've had an abort of any type, don't even think about
* actually doing the restart! */
if (is_handle_aborted(handle))
int need_copy = 0;
unsigned long start_lock, time_lock;
- WARN_ON(!transaction);
if (is_handle_aborted(handle))
return -EROFS;
journal = transaction->t_journal;
int err;
jbd_debug(5, "journal_head %p\n", jh);
- WARN_ON(!transaction);
err = -EROFS;
if (is_handle_aborted(handle))
goto out;
struct journal_head *jh;
int ret = 0;
- WARN_ON(!transaction);
if (is_handle_aborted(handle))
return -EROFS;
journal = transaction->t_journal;
int err = 0;
int was_modified = 0;
- WARN_ON(!transaction);
if (is_handle_aborted(handle))
return -EROFS;
journal = transaction->t_journal;
tid_t tid;
pid_t pid;
- if (!transaction)
- goto free_and_exit;
+ if (!transaction) {
+ /*
+ * Handle is already detached from the transaction so
+ * there is nothing to do other than decrease a refcount,
+ * or free the handle if refcount drops to zero
+ */
+ if (--handle->h_ref > 0) {
+ jbd_debug(4, "h_ref %d -> %d\n", handle->h_ref + 1,
+ handle->h_ref);
+ return err;
+ } else {
+ if (handle->h_rsv_handle)
+ jbd2_free_handle(handle->h_rsv_handle);
+ goto free_and_exit;
+ }
+ }
journal = transaction->t_journal;
J_ASSERT(journal_current_handle() == handle);
transaction_t *transaction = handle->h_transaction;
journal_t *journal;
- WARN_ON(!transaction);
if (is_handle_aborted(handle))
return -EROFS;
journal = transaction->t_journal;
if (!kn)
goto err_out1;
- ret = ida_simple_get(&root->ino_ida, 1, 0, GFP_KERNEL);
+ /*
+ * If the ino of the sysfs entry created for a kmem cache gets
+ * allocated from an ida layer, which is accounted to the memcg that
+ * owns the cache, the memcg will get pinned forever. So do not account
+ * ino ida allocations.
+ */
+ ret = ida_simple_get(&root->ino_ida, 1, 0,
+ GFP_KERNEL | __GFP_NOACCOUNT);
if (ret < 0)
goto err_out2;
kn->ino = ret;
#include <linux/mm.h>
#include <linux/delay.h>
#include <linux/errno.h>
+#include <linux/file.h>
#include <linux/string.h>
#include <linux/ratelimit.h>
#include <linux/printk.h>
p->server = server;
atomic_inc(&lsp->ls_count);
p->ctx = get_nfs_open_context(ctx);
+ get_file(fl->fl_file);
memcpy(&p->fl, fl, sizeof(p->fl));
return p;
out_free_seqid:
nfs_free_seqid(data->arg.lock_seqid);
nfs4_put_lock_state(data->lsp);
put_nfs_open_context(data->ctx);
+ fput(data->fl.fl_file);
kfree(data);
dprintk("%s: done!\n", __func__);
}
trace_nfs_writeback_inode_enter(inode);
ret = filemap_write_and_wait(inode->i_mapping);
- if (!ret) {
- ret = nfs_commit_inode(inode, FLUSH_SYNC);
- if (!ret)
- pnfs_sync_inode(inode, true);
- }
+ if (ret)
+ goto out;
+ ret = nfs_commit_inode(inode, FLUSH_SYNC);
+ if (ret < 0)
+ goto out;
+ pnfs_sync_inode(inode, true);
+ ret = 0;
+out:
trace_nfs_writeback_inode_exit(inode, ret);
return ret;
}
}
const struct nfsd4_layout_ops bl_layout_ops = {
+ /*
+ * Pretend that we send notification to the client. This is a blatant
+ * lie to force recent Linux clients to cache our device IDs.
+ * We rarely ever change the device ID, so the harm of leaking deviceids
+ * for a while isn't too bad. Unfortunately RFC5661 is a complete mess
+ * in this regard, but I filed errata 4119 for this a while ago, and
+ * hopefully the Linux client will eventually start caching deviceids
+ * without this again.
+ */
+ .notify_types =
+ NOTIFY_DEVICEID4_DELETE | NOTIFY_DEVICEID4_CHANGE,
.proc_getdeviceinfo = nfsd4_block_proc_getdeviceinfo,
.encode_getdeviceinfo = nfsd4_block_encode_getdeviceinfo,
.proc_layoutget = nfsd4_block_proc_layoutget,
}
static int decode_cb_op_status(struct xdr_stream *xdr, enum nfs_opnum4 expected,
- enum nfsstat4 *status)
+ int *status)
{
__be32 *p;
u32 op;
op = be32_to_cpup(p++);
if (unlikely(op != expected))
goto out_unexpected;
- *status = be32_to_cpup(p);
+ *status = nfs_cb_stat_to_errno(be32_to_cpup(p));
return 0;
out_overflow:
print_overflow_msg(__func__, xdr);
static int decode_cb_sequence4res(struct xdr_stream *xdr,
struct nfsd4_callback *cb)
{
- enum nfsstat4 nfserr;
int status;
if (cb->cb_minorversion == 0)
return 0;
- status = decode_cb_op_status(xdr, OP_CB_SEQUENCE, &nfserr);
- if (unlikely(status))
- goto out;
- if (unlikely(nfserr != NFS4_OK))
- goto out_default;
- status = decode_cb_sequence4resok(xdr, cb);
-out:
- return status;
-out_default:
- return nfs_cb_stat_to_errno(nfserr);
+ status = decode_cb_op_status(xdr, OP_CB_SEQUENCE, &cb->cb_status);
+ if (unlikely(status || cb->cb_status))
+ return status;
+
+ return decode_cb_sequence4resok(xdr, cb);
}
/*
struct nfsd4_callback *cb)
{
struct nfs4_cb_compound_hdr hdr;
- enum nfsstat4 nfserr;
int status;
status = decode_cb_compound4res(xdr, &hdr);
if (unlikely(status))
- goto out;
+ return status;
if (cb != NULL) {
status = decode_cb_sequence4res(xdr, cb);
- if (unlikely(status))
- goto out;
+ if (unlikely(status || cb->cb_status))
+ return status;
}
- status = decode_cb_op_status(xdr, OP_CB_RECALL, &nfserr);
- if (unlikely(status))
- goto out;
- if (unlikely(nfserr != NFS4_OK))
- status = nfs_cb_stat_to_errno(nfserr);
-out:
- return status;
+ return decode_cb_op_status(xdr, OP_CB_RECALL, &cb->cb_status);
}
#ifdef CONFIG_NFSD_PNFS
struct nfsd4_callback *cb)
{
struct nfs4_cb_compound_hdr hdr;
- enum nfsstat4 nfserr;
int status;
status = decode_cb_compound4res(xdr, &hdr);
if (unlikely(status))
- goto out;
+ return status;
+
if (cb) {
status = decode_cb_sequence4res(xdr, cb);
- if (unlikely(status))
- goto out;
+ if (unlikely(status || cb->cb_status))
+ return status;
}
- status = decode_cb_op_status(xdr, OP_CB_LAYOUTRECALL, &nfserr);
- if (unlikely(status))
- goto out;
- if (unlikely(nfserr != NFS4_OK))
- status = nfs_cb_stat_to_errno(nfserr);
-out:
- return status;
+ return decode_cb_op_status(xdr, OP_CB_LAYOUTRECALL, &cb->cb_status);
}
#endif /* CONFIG_NFSD_PNFS */
if (!nfsd41_cb_get_slot(clp, task))
return;
}
- spin_lock(&clp->cl_lock);
- if (list_empty(&cb->cb_per_client)) {
- /* This is the first call, not a restart */
- cb->cb_done = false;
- list_add(&cb->cb_per_client, &clp->cl_callbacks);
- }
- spin_unlock(&clp->cl_lock);
rpc_call_start(task);
}
if (clp->cl_minorversion) {
/* No need for lock, access serialized in nfsd4_cb_prepare */
- ++clp->cl_cb_session->se_cb_seq_nr;
+ if (!task->tk_status)
+ ++clp->cl_cb_session->se_cb_seq_nr;
clear_bit(0, &clp->cl_cb_slot_busy);
rpc_wake_up_next(&clp->cl_cb_waitq);
dprintk("%s: freed slot, new seqid=%d\n", __func__,
clp->cl_cb_session->se_cb_seq_nr);
}
- if (clp->cl_cb_client != task->tk_client) {
- /* We're shutting down or changing cl_cb_client; leave
- * it to nfsd4_process_cb_update to restart the call if
- * necessary. */
+ /*
+ * If the backchannel connection was shut down while this
+ * task was queued, we need to resubmit it after setting up
+ * a new backchannel connection.
+ *
+ * Note that if we lost our callback connection permanently
+ * the submission code will error out, so we don't need to
+ * handle that case here.
+ */
+ if (task->tk_flags & RPC_TASK_KILLED) {
+ task->tk_status = 0;
+ cb->cb_need_restart = true;
return;
}
- if (cb->cb_done)
- return;
+ if (cb->cb_status) {
+ WARN_ON_ONCE(task->tk_status);
+ task->tk_status = cb->cb_status;
+ }
switch (cb->cb_ops->done(cb, task)) {
case 0:
default:
BUG();
}
- cb->cb_done = true;
}
static void nfsd4_cb_release(void *calldata)
{
struct nfsd4_callback *cb = calldata;
- struct nfs4_client *clp = cb->cb_clp;
-
- if (cb->cb_done) {
- spin_lock(&clp->cl_lock);
- list_del(&cb->cb_per_client);
- spin_unlock(&clp->cl_lock);
+ if (cb->cb_need_restart)
+ nfsd4_run_cb(cb);
+ else
cb->cb_ops->release(cb);
- }
+
}
static const struct rpc_call_ops nfsd4_cb_ops = {
nfsd4_mark_cb_down(clp, err);
return;
}
- /* Yay, the callback channel's back! Restart any callbacks: */
- list_for_each_entry(cb, &clp->cl_callbacks, cb_per_client)
- queue_work(callback_wq, &cb->cb_work);
}
static void
struct nfs4_client *clp = cb->cb_clp;
struct rpc_clnt *clnt;
- if (cb->cb_ops && cb->cb_ops->prepare)
- cb->cb_ops->prepare(cb);
+ if (cb->cb_need_restart) {
+ cb->cb_need_restart = false;
+ } else {
+ if (cb->cb_ops && cb->cb_ops->prepare)
+ cb->cb_ops->prepare(cb);
+ }
if (clp->cl_flags & NFSD4_CLIENT_CB_FLAG_MASK)
nfsd4_process_cb_update(cb);
cb->cb_ops->release(cb);
return;
}
+
+ /*
+ * Don't send probe messages for 4.1 or later.
+ */
+ if (!cb->cb_ops && clp->cl_minorversion) {
+ clp->cl_cb_state = NFSD4_CB_UP;
+ return;
+ }
+
cb->cb_msg.rpc_cred = clp->cl_cb_cred;
rpc_call_async(clnt, &cb->cb_msg, RPC_TASK_SOFT | RPC_TASK_SOFTCONN,
cb->cb_ops ? &nfsd4_cb_ops : &nfsd4_cb_probe_ops, cb);
cb->cb_msg.rpc_resp = cb;
cb->cb_ops = ops;
INIT_WORK(&cb->cb_work, nfsd4_run_cb_work);
- INIT_LIST_HEAD(&cb->cb_per_client);
- cb->cb_done = true;
+ cb->cb_status = 0;
+ cb->cb_need_restart = false;
}
void nfsd4_run_cb(struct nfsd4_callback *cb)
static struct kmem_cache *file_slab;
static struct kmem_cache *stateid_slab;
static struct kmem_cache *deleg_slab;
+static struct kmem_cache *odstate_slab;
static void free_session(struct nfsd4_session *);
if (atomic_dec_and_lock(&fi->fi_ref, &state_lock)) {
hlist_del_rcu(&fi->fi_hash);
spin_unlock(&state_lock);
+ WARN_ON_ONCE(!list_empty(&fi->fi_clnt_odstate));
WARN_ON_ONCE(!list_empty(&fi->fi_delegations));
call_rcu(&fi->fi_rcu, nfsd4_free_file_rcu);
}
__nfs4_file_put_access(fp, O_RDONLY);
}
+/*
+ * Allocate a new open/delegation state counter. This is needed for
+ * pNFS for proper return on close semantics.
+ *
+ * Note that we only allocate it for pNFS-enabled exports, otherwise
+ * all pointers to struct nfs4_clnt_odstate are always NULL.
+ */
+static struct nfs4_clnt_odstate *
+alloc_clnt_odstate(struct nfs4_client *clp)
+{
+ struct nfs4_clnt_odstate *co;
+
+ co = kmem_cache_zalloc(odstate_slab, GFP_KERNEL);
+ if (co) {
+ co->co_client = clp;
+ atomic_set(&co->co_odcount, 1);
+ }
+ return co;
+}
+
+static void
+hash_clnt_odstate_locked(struct nfs4_clnt_odstate *co)
+{
+ struct nfs4_file *fp = co->co_file;
+
+ lockdep_assert_held(&fp->fi_lock);
+ list_add(&co->co_perfile, &fp->fi_clnt_odstate);
+}
+
+static inline void
+get_clnt_odstate(struct nfs4_clnt_odstate *co)
+{
+ if (co)
+ atomic_inc(&co->co_odcount);
+}
+
+static void
+put_clnt_odstate(struct nfs4_clnt_odstate *co)
+{
+ struct nfs4_file *fp;
+
+ if (!co)
+ return;
+
+ fp = co->co_file;
+ if (atomic_dec_and_lock(&co->co_odcount, &fp->fi_lock)) {
+ list_del(&co->co_perfile);
+ spin_unlock(&fp->fi_lock);
+
+ nfsd4_return_all_file_layouts(co->co_client, fp);
+ kmem_cache_free(odstate_slab, co);
+ }
+}
+
+static struct nfs4_clnt_odstate *
+find_or_hash_clnt_odstate(struct nfs4_file *fp, struct nfs4_clnt_odstate *new)
+{
+ struct nfs4_clnt_odstate *co;
+ struct nfs4_client *cl;
+
+ if (!new)
+ return NULL;
+
+ cl = new->co_client;
+
+ spin_lock(&fp->fi_lock);
+ list_for_each_entry(co, &fp->fi_clnt_odstate, co_perfile) {
+ if (co->co_client == cl) {
+ get_clnt_odstate(co);
+ goto out;
+ }
+ }
+ co = new;
+ co->co_file = fp;
+ hash_clnt_odstate_locked(new);
+out:
+ spin_unlock(&fp->fi_lock);
+ return co;
+}
+
struct nfs4_stid *nfs4_alloc_stid(struct nfs4_client *cl,
struct kmem_cache *slab)
{
}
static struct nfs4_delegation *
-alloc_init_deleg(struct nfs4_client *clp, struct svc_fh *current_fh)
+alloc_init_deleg(struct nfs4_client *clp, struct svc_fh *current_fh,
+ struct nfs4_clnt_odstate *odstate)
{
struct nfs4_delegation *dp;
long n;
INIT_LIST_HEAD(&dp->dl_perfile);
INIT_LIST_HEAD(&dp->dl_perclnt);
INIT_LIST_HEAD(&dp->dl_recall_lru);
+ dp->dl_clnt_odstate = odstate;
+ get_clnt_odstate(odstate);
dp->dl_type = NFS4_OPEN_DELEGATE_READ;
dp->dl_retries = 1;
nfsd4_init_cb(&dp->dl_recall, dp->dl_stid.sc_client,
spin_lock(&state_lock);
unhash_delegation_locked(dp);
spin_unlock(&state_lock);
+ put_clnt_odstate(dp->dl_clnt_odstate);
nfs4_put_deleg_lease(dp->dl_stid.sc_file);
nfs4_put_stid(&dp->dl_stid);
}
WARN_ON(!list_empty(&dp->dl_recall_lru));
+ put_clnt_odstate(dp->dl_clnt_odstate);
nfs4_put_deleg_lease(dp->dl_stid.sc_file);
if (clp->cl_minorversion == 0)
{
struct nfs4_ol_stateid *stp = openlockstateid(stid);
+ put_clnt_odstate(stp->st_clnt_odstate);
release_all_access(stp);
if (stp->st_stateowner)
nfs4_put_stateowner(stp->st_stateowner);
INIT_LIST_HEAD(&clp->cl_openowners);
INIT_LIST_HEAD(&clp->cl_delegations);
INIT_LIST_HEAD(&clp->cl_lru);
- INIT_LIST_HEAD(&clp->cl_callbacks);
INIT_LIST_HEAD(&clp->cl_revoked);
#ifdef CONFIG_NFSD_PNFS
INIT_LIST_HEAD(&clp->cl_lo_states);
while (!list_empty(&reaplist)) {
dp = list_entry(reaplist.next, struct nfs4_delegation, dl_recall_lru);
list_del_init(&dp->dl_recall_lru);
+ put_clnt_odstate(dp->dl_clnt_odstate);
nfs4_put_deleg_lease(dp->dl_stid.sc_file);
nfs4_put_stid(&dp->dl_stid);
}
spin_lock_init(&fp->fi_lock);
INIT_LIST_HEAD(&fp->fi_stateids);
INIT_LIST_HEAD(&fp->fi_delegations);
+ INIT_LIST_HEAD(&fp->fi_clnt_odstate);
fh_copy_shallow(&fp->fi_fhandle, fh);
fp->fi_deleg_file = NULL;
fp->fi_had_conflict = false;
void
nfsd4_free_slabs(void)
{
+ kmem_cache_destroy(odstate_slab);
kmem_cache_destroy(openowner_slab);
kmem_cache_destroy(lockowner_slab);
kmem_cache_destroy(file_slab);
sizeof(struct nfs4_delegation), 0, 0, NULL);
if (deleg_slab == NULL)
goto out_free_stateid_slab;
+ odstate_slab = kmem_cache_create("nfsd4_odstate",
+ sizeof(struct nfs4_clnt_odstate), 0, 0, NULL);
+ if (odstate_slab == NULL)
+ goto out_free_deleg_slab;
return 0;
+out_free_deleg_slab:
+ kmem_cache_destroy(deleg_slab);
out_free_stateid_slab:
kmem_cache_destroy(stateid_slab);
out_free_file_slab:
open->op_stp = nfs4_alloc_open_stateid(clp);
if (!open->op_stp)
return nfserr_jukebox;
+
+ if (nfsd4_has_session(cstate) &&
+ (cstate->current_fh.fh_export->ex_flags & NFSEXP_PNFS)) {
+ open->op_odstate = alloc_clnt_odstate(clp);
+ if (!open->op_odstate)
+ return nfserr_jukebox;
+ }
+
return nfs_ok;
}
static struct nfs4_delegation *
nfs4_set_delegation(struct nfs4_client *clp, struct svc_fh *fh,
- struct nfs4_file *fp)
+ struct nfs4_file *fp, struct nfs4_clnt_odstate *odstate)
{
int status;
struct nfs4_delegation *dp;
if (fp->fi_had_conflict)
return ERR_PTR(-EAGAIN);
- dp = alloc_init_deleg(clp, fh);
+ dp = alloc_init_deleg(clp, fh, odstate);
if (!dp)
return ERR_PTR(-ENOMEM);
spin_unlock(&state_lock);
out:
if (status) {
+ put_clnt_odstate(dp->dl_clnt_odstate);
nfs4_put_stid(&dp->dl_stid);
return ERR_PTR(status);
}
default:
goto out_no_deleg;
}
- dp = nfs4_set_delegation(clp, fh, stp->st_stid.sc_file);
+ dp = nfs4_set_delegation(clp, fh, stp->st_stid.sc_file, stp->st_clnt_odstate);
if (IS_ERR(dp))
goto out_no_deleg;
release_open_stateid(stp);
goto out;
}
+
+ stp->st_clnt_odstate = find_or_hash_clnt_odstate(fp,
+ open->op_odstate);
+ if (stp->st_clnt_odstate == open->op_odstate)
+ open->op_odstate = NULL;
}
update_stateid(&stp->st_stid.sc_stateid);
memcpy(&open->op_stateid, &stp->st_stid.sc_stateid, sizeof(stateid_t));
kmem_cache_free(file_slab, open->op_file);
if (open->op_stp)
nfs4_put_stid(&open->op_stp->st_stid);
+ if (open->op_odstate)
+ kmem_cache_free(odstate_slab, open->op_odstate);
}
__be32
return nfserr_old_stateid;
}
+static __be32 nfsd4_check_openowner_confirmed(struct nfs4_ol_stateid *ols)
+{
+ if (ols->st_stateowner->so_is_open_owner &&
+ !(openowner(ols->st_stateowner)->oo_flags & NFS4_OO_CONFIRMED))
+ return nfserr_bad_stateid;
+ return nfs_ok;
+}
+
static __be32 nfsd4_validate_stateid(struct nfs4_client *cl, stateid_t *stateid)
{
struct nfs4_stid *s;
- struct nfs4_ol_stateid *ols;
__be32 status = nfserr_bad_stateid;
if (ZERO_STATEID(stateid) || ONE_STATEID(stateid))
break;
case NFS4_OPEN_STID:
case NFS4_LOCK_STID:
- ols = openlockstateid(s);
- if (ols->st_stateowner->so_is_open_owner
- && !(openowner(ols->st_stateowner)->oo_flags
- & NFS4_OO_CONFIRMED))
- status = nfserr_bad_stateid;
- else
- status = nfs_ok;
+ status = nfsd4_check_openowner_confirmed(openlockstateid(s));
break;
default:
printk("unknown stateid type %x\n", s->sc_type);
status = nfs4_check_fh(current_fh, stp);
if (status)
goto out;
- if (stp->st_stateowner->so_is_open_owner
- && !(openowner(stp->st_stateowner)->oo_flags & NFS4_OO_CONFIRMED))
+ status = nfsd4_check_openowner_confirmed(stp);
+ if (status)
goto out;
status = nfs4_check_openmode(stp, flags);
if (status)
update_stateid(&stp->st_stid.sc_stateid);
memcpy(&close->cl_stateid, &stp->st_stid.sc_stateid, sizeof(stateid_t));
- nfsd4_return_all_file_layouts(stp->st_stateowner->so_client,
- stp->st_stid.sc_file);
-
nfsd4_close_open_stateid(stp);
/* put reference from nfs4_preprocess_seqid_op */
list_for_each_safe(pos, next, &reaplist) {
dp = list_entry (pos, struct nfs4_delegation, dl_recall_lru);
list_del_init(&dp->dl_recall_lru);
+ put_clnt_odstate(dp->dl_clnt_odstate);
nfs4_put_deleg_lease(dp->dl_stid.sc_file);
nfs4_put_stid(&dp->dl_stid);
}
struct nfsd4_callback {
struct nfs4_client *cb_clp;
- struct list_head cb_per_client;
u32 cb_minorversion;
struct rpc_message cb_msg;
struct nfsd4_callback_ops *cb_ops;
struct work_struct cb_work;
- bool cb_done;
+ int cb_status;
+ bool cb_need_restart;
};
struct nfsd4_callback_ops {
struct list_head dl_perfile;
struct list_head dl_perclnt;
struct list_head dl_recall_lru; /* delegation recalled */
+ struct nfs4_clnt_odstate *dl_clnt_odstate;
u32 dl_type;
time_t dl_time;
/* For recall: */
int cl_cb_state;
struct nfsd4_callback cl_cb_null;
struct nfsd4_session *cl_cb_session;
- struct list_head cl_callbacks; /* list of in-progress callbacks */
/* for all client information that callback code might need: */
spinlock_t cl_lock;
return container_of(so, struct nfs4_lockowner, lo_owner);
}
+/*
+ * Per-client state indicating no. of opens and outstanding delegations
+ * on a file from a particular client.'od' stands for 'open & delegation'
+ */
+struct nfs4_clnt_odstate {
+ struct nfs4_client *co_client;
+ struct nfs4_file *co_file;
+ struct list_head co_perfile;
+ atomic_t co_odcount;
+};
+
/*
* nfs4_file: a file opened by some number of (open) nfs4_stateowners.
*
struct list_head fi_delegations;
struct rcu_head fi_rcu;
};
+ struct list_head fi_clnt_odstate;
/* One each for O_RDONLY, O_WRONLY, O_RDWR: */
struct file * fi_fds[3];
/*
struct list_head st_perstateowner;
struct list_head st_locks;
struct nfs4_stateowner * st_stateowner;
+ struct nfs4_clnt_odstate * st_clnt_odstate;
unsigned char st_access_bmap;
unsigned char st_deny_bmap;
struct nfs4_ol_stateid * st_openstp;
struct nfs4_openowner *op_openowner; /* used during processing */
struct nfs4_file *op_file; /* used during processing */
struct nfs4_ol_stateid *op_stp; /* used during processing */
+ struct nfs4_clnt_odstate *op_odstate; /* used during processing */
struct nfs4_acl *op_acl;
struct xdr_netobj op_label;
};
struct cred *override_cred;
char *link = NULL;
+ if (WARN_ON(!workdir))
+ return -EROFS;
+
ovl_path_upper(parent, &parentpath);
upperdir = parentpath.dentry;
struct kstat stat;
int err;
+ if (WARN_ON(!workdir))
+ return ERR_PTR(-EROFS);
+
err = ovl_lock_rename_workdir(workdir, upperdir);
if (err)
goto out;
struct dentry *newdentry;
int err;
+ if (WARN_ON(!workdir))
+ return -EROFS;
+
err = ovl_lock_rename_workdir(workdir, upperdir);
if (err)
goto out;
struct dentry *opaquedir = NULL;
int err;
- if (is_dir && OVL_TYPE_MERGE_OR_LOWER(ovl_path_type(dentry))) {
- opaquedir = ovl_check_empty_and_clear(dentry);
- err = PTR_ERR(opaquedir);
- if (IS_ERR(opaquedir))
- goto out;
+ if (WARN_ON(!workdir))
+ return -EROFS;
+
+ if (is_dir) {
+ if (OVL_TYPE_MERGE_OR_LOWER(ovl_path_type(dentry))) {
+ opaquedir = ovl_check_empty_and_clear(dentry);
+ err = PTR_ERR(opaquedir);
+ if (IS_ERR(opaquedir))
+ goto out;
+ } else {
+ LIST_HEAD(list);
+
+ /*
+ * When removing an empty opaque directory, then it
+ * makes no sense to replace it with an exact replica of
+ * itself. But emptiness still needs to be checked.
+ */
+ err = ovl_check_empty_dir(dentry, &list);
+ ovl_cache_free(&list);
+ if (err)
+ goto out;
+ }
}
err = ovl_lock_rename_workdir(workdir, upperdir);
{
struct ovl_fs *ufs = sb->s_fs_info;
- if (!(*flags & MS_RDONLY) && !ufs->upper_mnt)
+ if (!(*flags & MS_RDONLY) && (!ufs->upper_mnt || !ufs->workdir))
return -EROFS;
return 0;
ufs->workdir = ovl_workdir_create(ufs->upper_mnt, workpath.dentry);
err = PTR_ERR(ufs->workdir);
if (IS_ERR(ufs->workdir)) {
- pr_err("overlayfs: failed to create directory %s/%s\n",
- ufs->config.workdir, OVL_WORKDIR_NAME);
- goto out_put_upper_mnt;
+ pr_warn("overlayfs: failed to create directory %s/%s (errno: %i); mounting read-only\n",
+ ufs->config.workdir, OVL_WORKDIR_NAME, -err);
+ sb->s_flags |= MS_RDONLY;
+ ufs->workdir = NULL;
}
}
kfree(ufs->lower_mnt);
out_put_workdir:
dput(ufs->workdir);
-out_put_upper_mnt:
mntput(ufs->upper_mnt);
out_put_lowerpath:
for (i = 0; i < numlower; i++)
{0x1002, 0x6658, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BONAIRE|RADEON_NEW_MEMMAP}, \
{0x1002, 0x665c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BONAIRE|RADEON_NEW_MEMMAP}, \
{0x1002, 0x665d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BONAIRE|RADEON_NEW_MEMMAP}, \
+ {0x1002, 0x665f, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_BONAIRE|RADEON_NEW_MEMMAP}, \
{0x1002, 0x6660, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_HAINAN|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
{0x1002, 0x6663, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_HAINAN|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
{0x1002, 0x6664, PCI_ANY_ID, PCI_ANY_ID, 0, 0, CHIP_HAINAN|RADEON_IS_MOBILITY|RADEON_NEW_MEMMAP}, \
extern int sg_scsi_ioctl(struct request_queue *, struct gendisk *, fmode_t,
struct scsi_ioctl_command __user *);
-extern void blk_queue_bio(struct request_queue *q, struct bio *bio);
-
/*
* A queue has just exitted congestion. Note this in the global counter of
* congested queues, and wake up anyone who was waiting for requests to be
#define PHY_ID_BCM7250 0xae025280
#define PHY_ID_BCM7364 0xae025260
#define PHY_ID_BCM7366 0x600d8490
-#define PHY_ID_BCM7425 0x03625e60
+#define PHY_ID_BCM7425 0x600d86b0
#define PHY_ID_BCM7429 0x600d8730
#define PHY_ID_BCM7439 0x600d8480
#define PHY_ID_BCM7439_2 0xae025080
#define ___GFP_HARDWALL 0x20000u
#define ___GFP_THISNODE 0x40000u
#define ___GFP_RECLAIMABLE 0x80000u
+#define ___GFP_NOACCOUNT 0x100000u
#define ___GFP_NOTRACK 0x200000u
#define ___GFP_NO_KSWAPD 0x400000u
#define ___GFP_OTHER_NODE 0x800000u
#define __GFP_HARDWALL ((__force gfp_t)___GFP_HARDWALL) /* Enforce hardwall cpuset memory allocs */
#define __GFP_THISNODE ((__force gfp_t)___GFP_THISNODE)/* No fallback, no policies */
#define __GFP_RECLAIMABLE ((__force gfp_t)___GFP_RECLAIMABLE) /* Page is reclaimable */
+#define __GFP_NOACCOUNT ((__force gfp_t)___GFP_NOACCOUNT) /* Don't account to kmemcg */
#define __GFP_NOTRACK ((__force gfp_t)___GFP_NOTRACK) /* Don't track with kmemcheck */
#define __GFP_NO_KSWAPD ((__force gfp_t)___GFP_NO_KSWAPD)
* @usage: Usage id for this hub device instance.
* @start_collection_index: Starting index for a phy type collection
* @end_collection_index: Last index for a phy type collection
- * @mutex: synchronizing mutex.
+ * @mutex_ptr: synchronizing mutex pointer.
* @pending: Holds information of pending sync read request.
*/
struct hid_sensor_hub_device {
u32 usage;
int start_collection_index;
int end_collection_index;
- struct mutex mutex;
+ struct mutex *mutex_ptr;
struct sensor_hub_pending pending;
};
}
#if BITS_PER_LONG < 64
-extern u64 __ktime_divns(const ktime_t kt, s64 div);
-static inline u64 ktime_divns(const ktime_t kt, s64 div)
+extern s64 __ktime_divns(const ktime_t kt, s64 div);
+static inline s64 ktime_divns(const ktime_t kt, s64 div)
{
+ /*
+ * Negative divisors could cause an inf loop,
+ * so bug out here.
+ */
+ BUG_ON(div < 0);
if (__builtin_constant_p(div) && !(div >> 32)) {
- u64 ns = kt.tv64;
- do_div(ns, div);
- return ns;
+ s64 ns = kt.tv64;
+ u64 tmp = ns < 0 ? -ns : ns;
+
+ do_div(tmp, div);
+ return ns < 0 ? -tmp : tmp;
} else {
return __ktime_divns(kt, div);
}
}
#else /* BITS_PER_LONG < 64 */
-# define ktime_divns(kt, div) (u64)((kt).tv64 / (div))
+static inline s64 ktime_divns(const ktime_t kt, s64 div)
+{
+ /*
+ * 32-bit implementation cannot handle negative divisors,
+ * so catch them on 64bit as well.
+ */
+ WARN_ON(div < 0);
+ return kt.tv64 / div;
+}
#endif
static inline s64 ktime_to_us(const ktime_t kt)
ATA_LFLAG_SW_ACTIVITY = (1 << 7), /* keep activity stats */
ATA_LFLAG_NO_LPM = (1 << 8), /* disable LPM on this link */
ATA_LFLAG_RST_ONCE = (1 << 9), /* limit recovery to one reset */
+ ATA_LFLAG_CHANGED = (1 << 10), /* LPM state changed on this link */
/* struct ata_port flags */
ATA_FLAG_SLAVE_POSS = (1 << 0), /* host supports slave dev */
*/
ATA_TMOUT_PMP_SRST_WAIT = 5000,
+ /* When the LPM policy is set to ATA_LPM_MAX_POWER, there might
+ * be a spurious PHY event, so ignore the first PHY event that
+ * occurs within 10s after the policy change.
+ */
+ ATA_TMOUT_SPURIOUS_PHY = 10000,
+
/* ATA bus states */
BUS_UNKNOWN = 0,
BUS_DMA = 1,
struct ata_eh_context eh_context;
struct ata_device device[ATA_MAX_DEVICES];
+
+ unsigned long last_lpm_change; /* when last LPM change happened */
};
#define ATA_LINK_CLEAR_BEGIN offsetof(struct ata_link, active_tag)
#define ATA_LINK_CLEAR_END offsetof(struct ata_link, device[0])
extern int ata_do_set_mode(struct ata_link *link, struct ata_device **r_failed_dev);
extern void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap);
extern void ata_scsi_cmd_error_handler(struct Scsi_Host *host, struct ata_port *ap, struct list_head *eh_q);
+extern bool sata_lpm_ignore_phy_events(struct ata_link *link);
extern int ata_cable_40wire(struct ata_port *ap);
extern int ata_cable_80wire(struct ata_port *ap);
if (!memcg_kmem_enabled())
return true;
+ if (gfp & __GFP_NOACCOUNT)
+ return true;
/*
* __GFP_NOFAIL allocations will move on even if charging is not
* possible. Therefore we don't even try, and have this allocation
{
if (!memcg_kmem_enabled())
return cachep;
+ if (gfp & __GFP_NOACCOUNT)
+ return cachep;
if (gfp & __GFP_NOFAIL)
return cachep;
if (in_interrupt() || (!current->mm) || (current->flags & PF_KTHREAD))
#ifndef _LINUX_NETDEVICE_H
#define _LINUX_NETDEVICE_H
-#include <linux/pm_qos.h>
#include <linux/timer.h>
#include <linux/bug.h>
#include <linux/delay.h>
*
* @qdisc_tx_busylock: XXX: need comments on this one
*
- * @pm_qos_req: Power Management QoS object
- *
* FIXME: cleanup struct net_device such that network protocol info
* moves out.
*/
#ifndef __LINUX_PLATFORM_DATA_SI5351_H__
#define __LINUX_PLATFORM_DATA_SI5351_H__
-struct clk;
-
/**
* enum si5351_pll_src - Si5351 pll clock source
* @SI5351_PLL_SRC_DEFAULT: default, do not change eeprom config
* @clkout: array of clkout configuration
*/
struct si5351_platform_data {
- struct clk *clk_xtal;
- struct clk *clk_clkin;
enum si5351_pll_src pll_src[2];
struct si5351_clkout_config clkout[8];
};
#ifndef _LINUX_RHASHTABLE_H
#define _LINUX_RHASHTABLE_H
+#include <linux/atomic.h>
#include <linux/compiler.h>
#include <linux/errno.h>
#include <linux/jhash.h>
* @key_len: Length of key
* @key_offset: Offset of key in struct to be hashed
* @head_offset: Offset of rhash_head in struct to be hashed
+ * @insecure_max_entries: Maximum number of entries (may be exceeded)
* @max_size: Maximum size while expanding
* @min_size: Minimum size while shrinking
* @nulls_base: Base value to generate nulls marker
size_t key_len;
size_t key_offset;
size_t head_offset;
+ unsigned int insecure_max_entries;
unsigned int max_size;
unsigned int min_size;
u32 nulls_base;
(!ht->p.max_size || tbl->size < ht->p.max_size);
}
+/**
+ * rht_grow_above_max - returns true if table is above maximum
+ * @ht: hash table
+ * @tbl: current table
+ */
+static inline bool rht_grow_above_max(const struct rhashtable *ht,
+ const struct bucket_table *tbl)
+{
+ return ht->p.insecure_max_entries &&
+ atomic_read(&ht->nelems) >= ht->p.insecure_max_entries;
+}
+
/* The bucket lock is selected based on the hash and protects mutations
* on a group of hash buckets.
*
goto out;
}
+ err = -E2BIG;
+ if (unlikely(rht_grow_above_max(ht, tbl)))
+ goto out;
+
if (unlikely(rht_grow_above_100(ht, tbl))) {
slow_path:
spin_unlock_bh(lock);
#ifdef CONFIG_RT_MUTEXES
extern int rt_mutex_getprio(struct task_struct *p);
extern void rt_mutex_setprio(struct task_struct *p, int prio);
-extern int rt_mutex_check_prio(struct task_struct *task, int newprio);
+extern int rt_mutex_get_effective_prio(struct task_struct *task, int newprio);
extern struct task_struct *rt_mutex_get_top_task(struct task_struct *task);
extern void rt_mutex_adjust_pi(struct task_struct *p);
static inline bool tsk_is_pi_blocked(struct task_struct *tsk)
return p->normal_prio;
}
-static inline int rt_mutex_check_prio(struct task_struct *task, int newprio)
+static inline int rt_mutex_get_effective_prio(struct task_struct *task,
+ int newprio)
{
- return 0;
+ return newprio;
}
static inline struct task_struct *rt_mutex_get_top_task(struct task_struct *task)
struct net_device *physindev;
struct net_device *physoutdev;
char neigh_header[8];
+ __be32 ipv4_daddr;
};
#endif
* read the code and the spec side by side (and laugh ...)
* See RFC793 and RFC1122. The RFC writes these in capitals.
*/
+ u64 bytes_received; /* RFC4898 tcpEStatsAppHCThruOctetsReceived
+ * sum(delta(rcv_nxt)), or how many bytes
+ * were acked.
+ */
u32 rcv_nxt; /* What we want to receive next */
u32 copied_seq; /* Head of yet unread data */
u32 rcv_wup; /* rcv_nxt on last window update sent */
u32 snd_nxt; /* Next sequence we send */
+ u64 bytes_acked; /* RFC4898 tcpEStatsAppHCThruOctetsAcked
+ * sum(delta(snd_una)), or how many bytes
+ * were acked.
+ */
+ struct u64_stats_sync syncp; /* protects 64bit vars (cf tcp_get_info()) */
+
u32 snd_una; /* First byte we want an ack for */
u32 snd_sml; /* Last byte of the most recently transmitted small packet */
u32 rcv_tstamp; /* timestamp of last received ACK (for keepalives) */
#define TTY_EXCLUSIVE 3 /* Exclusive open mode */
#define TTY_DEBUG 4 /* Debugging */
#define TTY_DO_WRITE_WAKEUP 5 /* Call write_wakeup after queuing new */
+#define TTY_OTHER_DONE 6 /* Closed pty has completed input processing */
#define TTY_LDISC_OPEN 11 /* Line discipline is open */
#define TTY_PTY_LOCK 16 /* pty private */
#define TTY_NO_WRITE_SPLIT 17 /* Preserve write boundaries to driver */
extern void do_SAK(struct tty_struct *tty);
extern void __do_SAK(struct tty_struct *tty);
extern void no_tty(void);
-extern void tty_flush_to_ldisc(struct tty_struct *tty);
extern void tty_buffer_free_all(struct tty_port *port);
extern void tty_buffer_flush(struct tty_struct *tty, struct tty_ldisc *ld);
extern void tty_buffer_init(struct tty_port *port);
static inline bool uid_valid(kuid_t uid)
{
- return !uid_eq(uid, INVALID_UID);
+ return __kuid_val(uid) != (uid_t) -1;
}
static inline bool gid_valid(kgid_t gid)
{
- return !gid_eq(gid, INVALID_GID);
+ return __kgid_val(gid) != (gid_t) -1;
}
#ifdef CONFIG_USER_NS
struct cfg802154_ops {
struct net_device * (*add_virtual_intf_deprecated)(struct wpan_phy *wpan_phy,
const char *name,
+ unsigned char name_assign_type,
int type);
void (*del_virtual_intf_deprecated)(struct wpan_phy *wpan_phy,
struct net_device *dev);
int (*add_virtual_intf)(struct wpan_phy *wpan_phy,
const char *name,
+ unsigned char name_assign_type,
enum nl802154_iftype type,
__le64 extended_addr);
int (*del_virtual_intf)(struct wpan_phy *wpan_phy,
* struct codel_params - contains codel parameters
* @target: target queue size (in time units)
* @interval: width of moving time window
+ * @mtu: device mtu, or minimal queue backlog in bytes.
* @ecn: is Explicit Congestion Notification enabled
*/
struct codel_params {
codel_time_t target;
codel_time_t interval;
+ u32 mtu;
bool ecn;
};
u32 ecn_mark;
};
-static void codel_params_init(struct codel_params *params)
+static void codel_params_init(struct codel_params *params,
+ const struct Qdisc *sch)
{
params->interval = MS2TIME(100);
params->target = MS2TIME(5);
+ params->mtu = psched_mtu(qdisc_dev(sch));
params->ecn = false;
}
static void codel_stats_init(struct codel_stats *stats)
{
- stats->maxpacket = 256;
+ stats->maxpacket = 0;
}
/*
stats->maxpacket = qdisc_pkt_len(skb);
if (codel_time_before(vars->ldelay, params->target) ||
- sch->qstats.backlog <= stats->maxpacket) {
+ sch->qstats.backlog <= params->mtu) {
/* went below - stay below for at least interval */
vars->first_above_time = 0;
return false;
u32 probe_timestamp;
} icsk_mtup;
- u32 icsk_ca_priv[16];
u32 icsk_user_timeout;
-#define ICSK_CA_PRIV_SIZE (16 * sizeof(u32))
+
+ u64 icsk_ca_priv[64 / sizeof(u64)];
+#define ICSK_CA_PRIV_SIZE (8 * sizeof(u64))
};
#define ICSK_TIME_RETRANS 1 /* Retransmit timer */
* @sta: station table entry, %NULL for per-vif queue
* @tid: the TID for this queue (unused for per-vif queue)
* @ac: the AC for this queue
+ * @drv_priv: data area for driver use, will always be aligned to
+ * sizeof(void *).
*
* The driver can obtain packets from this queue by calling
* ieee80211_tx_dequeue().
__put_unaligned_memmove64(swab64p(le64_src), be64_dst);
}
-/* Basic interface to register ieee802154 device */
+/**
+ * ieee802154_alloc_hw - Allocate a new hardware device
+ *
+ * This must be called once for each hardware device. The returned pointer
+ * must be used to refer to this device when calling other functions.
+ * mac802154 allocates a private data area for the driver pointed to by
+ * @priv in &struct ieee802154_hw, the size of this area is given as
+ * @priv_data_len.
+ *
+ * @priv_data_len: length of private data
+ * @ops: callbacks for this device
+ *
+ * Return: A pointer to the new hardware device, or %NULL on error.
+ */
struct ieee802154_hw *
ieee802154_alloc_hw(size_t priv_data_len, const struct ieee802154_ops *ops);
+
+/**
+ * ieee802154_free_hw - free hardware descriptor
+ *
+ * This function frees everything that was allocated, including the
+ * private data for the driver. You must call ieee802154_unregister_hw()
+ * before calling this function.
+ *
+ * @hw: the hardware to free
+ */
void ieee802154_free_hw(struct ieee802154_hw *hw);
+
+/**
+ * ieee802154_register_hw - Register hardware device
+ *
+ * You must call this function before any other functions in
+ * mac802154. Note that before a hardware can be registered, you
+ * need to fill the contained wpan_phy's information.
+ *
+ * @hw: the device to register as returned by ieee802154_alloc_hw()
+ *
+ * Return: 0 on success. An error code otherwise.
+ */
int ieee802154_register_hw(struct ieee802154_hw *hw);
+
+/**
+ * ieee802154_unregister_hw - Unregister a hardware device
+ *
+ * This function instructs mac802154 to free allocated resources
+ * and unregister netdevices from the networking subsystem.
+ *
+ * @hw: the hardware to unregister
+ */
void ieee802154_unregister_hw(struct ieee802154_hw *hw);
+/**
+ * ieee802154_rx - receive frame
+ *
+ * Use this function to hand received frames to mac802154. The receive
+ * buffer in @skb must start with an IEEE 802.15.4 header. In case of a
+ * paged @skb is used, the driver is recommended to put the ieee802154
+ * header of the frame on the linear part of the @skb to avoid memory
+ * allocation and/or memcpy by the stack.
+ *
+ * This function may not be called in IRQ context. Calls to this function
+ * for a single hardware must be synchronized against each other.
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac802154 after this call
+ */
void ieee802154_rx(struct ieee802154_hw *hw, struct sk_buff *skb);
+
+/**
+ * ieee802154_rx_irqsafe - receive frame
+ *
+ * Like ieee802154_rx() but can be called in IRQ context
+ * (internally defers to a tasklet.)
+ *
+ * @hw: the hardware this frame came in on
+ * @skb: the buffer to receive, owned by mac802154 after this call
+ * @lqi: link quality indicator
+ */
void ieee802154_rx_irqsafe(struct ieee802154_hw *hw, struct sk_buff *skb,
u8 lqi);
-
+/**
+ * ieee802154_wake_queue - wake ieee802154 queue
+ * @hw: pointer as obtained from ieee802154_alloc_hw().
+ *
+ * Drivers should use this function instead of netif_wake_queue.
+ */
void ieee802154_wake_queue(struct ieee802154_hw *hw);
+
+/**
+ * ieee802154_stop_queue - stop ieee802154 queue
+ * @hw: pointer as obtained from ieee802154_alloc_hw().
+ *
+ * Drivers should use this function instead of netif_stop_queue.
+ */
void ieee802154_stop_queue(struct ieee802154_hw *hw);
+
+/**
+ * ieee802154_xmit_complete - frame transmission complete
+ *
+ * @hw: pointer as obtained from ieee802154_alloc_hw().
+ * @skb: buffer for transmission
+ * @ifs_handling: indicate interframe space handling
+ */
void ieee802154_xmit_complete(struct ieee802154_hw *hw, struct sk_buff *skb,
bool ifs_handling);
/* Map v4 address to v4-mapped v6 address */
static inline void sctp_v4_map_v6(union sctp_addr *addr)
{
+ __be16 port;
+
+ port = addr->v4.sin_port;
+ addr->v6.sin6_addr.s6_addr32[3] = addr->v4.sin_addr.s_addr;
+ addr->v6.sin6_port = port;
addr->v6.sin6_family = AF_INET6;
addr->v6.sin6_flowinfo = 0;
addr->v6.sin6_scope_id = 0;
- addr->v6.sin6_port = addr->v4.sin_port;
- addr->v6.sin6_addr.s6_addr32[3] = addr->v4.sin_addr.s_addr;
addr->v6.sin6_addr.s6_addr32[0] = 0;
addr->v6.sin6_addr.s6_addr32[1] = 0;
addr->v6.sin6_addr.s6_addr32[2] = htonl(0x0000ffff);
}
/* tcp.c */
-void tcp_get_info(const struct sock *, struct tcp_info *);
+void tcp_get_info(struct sock *, struct tcp_info *);
/* Read 'sendfile()'-style from a TCP socket */
typedef int (*sk_read_actor_t)(read_descriptor_t *, struct sk_buff *,
/* Requires ECN/ECT set on all packets */
#define TCP_CONG_NEEDS_ECN 0x2
+union tcp_cc_info;
+
struct tcp_congestion_ops {
struct list_head list;
u32 key;
/* hook for packet ack accounting (optional) */
void (*pkts_acked)(struct sock *sk, u32 num_acked, s32 rtt_us);
/* get info for inet_diag (optional) */
- int (*get_info)(struct sock *sk, u32 ext, struct sk_buff *skb);
+ size_t (*get_info)(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info);
char name[TCP_CA_NAME_MAX];
struct module *owner;
__u32 dctcp_ab_tot;
};
+union tcp_cc_info {
+ struct tcpvegas_info vegas;
+ struct tcp_dctcp_info dctcp;
+};
#endif /* _UAPI_INET_DIAG_H_ */
#define MPLS_LS_TTL_MASK 0x000000FF
#define MPLS_LS_TTL_SHIFT 0
+/* Reserved labels */
+#define MPLS_LABEL_IPV4NULL 0 /* RFC3032 */
+#define MPLS_LABEL_RTALERT 1 /* RFC3032 */
+#define MPLS_LABEL_IPV6NULL 2 /* RFC3032 */
+#define MPLS_LABEL_IMPLNULL 3 /* RFC3032 */
+#define MPLS_LABEL_ENTROPY 7 /* RFC6790 */
+#define MPLS_LABEL_GAL 13 /* RFC5586 */
+#define MPLS_LABEL_OAMALERT 14 /* RFC3429 */
+#define MPLS_LABEL_EXTENSION 15 /* RFC7274 */
+
#endif /* _UAPI_MPLS_H */
/* The field td_maxack has been set */
#define IP_CT_TCP_FLAG_MAXACK_SET 0x20
+/* Marks possibility for expected RFC5961 challenge ACK */
+#define IP_CT_EXP_CHALLENGE_ACK 0x40
+
struct nf_ct_tcp_flags {
__u8 flags;
__u8 mask;
#define RTNH_F_DEAD 1 /* Nexthop is dead (used by multipath) */
#define RTNH_F_PERVASIVE 2 /* Do recursive gateway lookup */
#define RTNH_F_ONLINK 4 /* Gateway is forced on link */
-#define RTNH_F_EXTERNAL 8 /* Route installed externally */
+#define RTNH_F_OFFLOAD 8 /* offloaded route */
/* Macros to handle hexthops */
#define TCP_FASTOPEN 23 /* Enable FastOpen on listeners */
#define TCP_TIMESTAMP 24
#define TCP_NOTSENT_LOWAT 25 /* limit number of unsent bytes in write queue */
+#define TCP_CC_INFO 26 /* Get Congestion Control (optional) info */
struct tcp_repair_opt {
__u32 opt_code;
__u64 tcpi_pacing_rate;
__u64 tcpi_max_pacing_rate;
+ __u64 tcpi_bytes_acked; /* RFC4898 tcpEStatsAppHCThruOctetsAcked */
+ __u64 tcpi_bytes_received; /* RFC4898 tcpEStatsAppHCThruOctetsReceived */
};
/* for TCP_MD5SIG socket option */
irq_handler_t handler,
unsigned long irqflags, const char *devname,
void *dev_id);
-int bind_virq_to_irq(unsigned int virq, unsigned int cpu);
+int bind_virq_to_irq(unsigned int virq, unsigned int cpu, bool percpu);
int bind_virq_to_irqhandler(unsigned int virq, unsigned int cpu,
irq_handler_t handler,
unsigned long irqflags, const char *devname,
* Those places that change perf_event::ctx will hold both
* perf_event_ctx::mutex of the 'old' and 'new' ctx value.
*
- * Lock ordering is by mutex address. There is one other site where
- * perf_event_context::mutex nests and that is put_event(). But remember that
- * that is a parent<->child context relation, and migration does not affect
- * children, therefore these two orderings should not interact.
+ * Lock ordering is by mutex address. There are two other sites where
+ * perf_event_context::mutex nests and those are:
+ *
+ * - perf_event_exit_task_context() [ child , 0 ]
+ * __perf_event_exit_task()
+ * sync_child_event()
+ * put_event() [ parent, 1 ]
+ *
+ * - perf_event_init_context() [ parent, 0 ]
+ * inherit_task_group()
+ * inherit_group()
+ * inherit_event()
+ * perf_event_alloc()
+ * perf_init_event()
+ * perf_try_init_event() [ child , 1 ]
+ *
+ * While it appears there is an obvious deadlock here -- the parent and child
+ * nesting levels are inverted between the two. This is in fact safe because
+ * life-time rules separate them. That is an exiting task cannot fork, and a
+ * spawning task cannot (yet) exit.
+ *
+ * But remember that that these are parent<->child context relations, and
+ * migration does not affect children, therefore these two orderings should not
+ * interact.
*
* The change in perf_event::ctx does not affect children (as claimed above)
* because the sys_perf_event_open() case will install a new event and break
}
}
-/*
- * Called when the last reference to the file is gone.
- */
static void put_event(struct perf_event *event)
{
struct perf_event_context *ctx;
}
EXPORT_SYMBOL_GPL(perf_event_release_kernel);
+/*
+ * Called when the last reference to the file is gone.
+ */
static int perf_release(struct inode *inode, struct file *file)
{
put_event(file->private_data);
return -ENODEV;
if (event->group_leader != event) {
- ctx = perf_event_ctx_lock(event->group_leader);
+ /*
+ * This ctx->mutex can nest when we're called through
+ * inheritance. See the perf_event_ctx_lock_nested() comment.
+ */
+ ctx = perf_event_ctx_lock_nested(event->group_leader,
+ SINGLE_DEPTH_NESTING);
BUG_ON(!ctx);
}
}
/*
- * Called by sched_setscheduler() to check whether the priority change
- * is overruled by a possible priority boosting.
+ * Called by sched_setscheduler() to get the priority which will be
+ * effective after the change.
*/
-int rt_mutex_check_prio(struct task_struct *task, int newprio)
+int rt_mutex_get_effective_prio(struct task_struct *task, int newprio)
{
if (!task_has_pi_waiters(task))
- return 0;
+ return newprio;
- return task_top_pi_waiter(task)->task->prio <= newprio;
+ if (task_top_pi_waiter(task)->task->prio <= newprio)
+ return task_top_pi_waiter(task)->task->prio;
+ return newprio;
}
/*
/* Actually do priority change: must hold pi & rq lock. */
static void __setscheduler(struct rq *rq, struct task_struct *p,
- const struct sched_attr *attr)
+ const struct sched_attr *attr, bool keep_boost)
{
__setscheduler_params(p, attr);
/*
- * If we get here, there was no pi waiters boosting the
- * task. It is safe to use the normal prio.
+ * Keep a potential priority boosting if called from
+ * sched_setscheduler().
*/
- p->prio = normal_prio(p);
+ if (keep_boost)
+ p->prio = rt_mutex_get_effective_prio(p, normal_prio(p));
+ else
+ p->prio = normal_prio(p);
if (dl_prio(p->prio))
p->sched_class = &dl_sched_class;
int newprio = dl_policy(attr->sched_policy) ? MAX_DL_PRIO - 1 :
MAX_RT_PRIO - 1 - attr->sched_priority;
int retval, oldprio, oldpolicy = -1, queued, running;
- int policy = attr->sched_policy;
+ int new_effective_prio, policy = attr->sched_policy;
unsigned long flags;
const struct sched_class *prev_class;
struct rq *rq;
oldprio = p->prio;
/*
- * Special case for priority boosted tasks.
- *
- * If the new priority is lower or equal (user space view)
- * than the current (boosted) priority, we just store the new
+ * Take priority boosted tasks into account. If the new
+ * effective priority is unchanged, we just store the new
* normal parameters and do not touch the scheduler class and
* the runqueue. This will be done when the task deboost
* itself.
*/
- if (rt_mutex_check_prio(p, newprio)) {
+ new_effective_prio = rt_mutex_get_effective_prio(p, newprio);
+ if (new_effective_prio == oldprio) {
__setscheduler_params(p, attr);
task_rq_unlock(rq, p, &flags);
return 0;
put_prev_task(rq, p);
prev_class = p->sched_class;
- __setscheduler(rq, p, attr);
+ __setscheduler(rq, p, attr, true);
if (running)
p->sched_class->set_curr_task(rq);
long ret;
current->in_iowait = 1;
- if (old_iowait)
- blk_schedule_flush_plug(current);
- else
- blk_flush_plug(current);
+ blk_schedule_flush_plug(current);
delayacct_blkio_start();
rq = raw_rq();
unsigned long flags;
long cpu = (long)hcpu;
struct dl_bw *dl_b;
+ bool overflow;
+ int cpus;
- switch (action & ~CPU_TASKS_FROZEN) {
+ switch (action) {
case CPU_DOWN_PREPARE:
- /* explicitly allow suspend */
- if (!(action & CPU_TASKS_FROZEN)) {
- bool overflow;
- int cpus;
-
- rcu_read_lock_sched();
- dl_b = dl_bw_of(cpu);
+ rcu_read_lock_sched();
+ dl_b = dl_bw_of(cpu);
- raw_spin_lock_irqsave(&dl_b->lock, flags);
- cpus = dl_bw_cpus(cpu);
- overflow = __dl_overflow(dl_b, cpus, 0, 0);
- raw_spin_unlock_irqrestore(&dl_b->lock, flags);
+ raw_spin_lock_irqsave(&dl_b->lock, flags);
+ cpus = dl_bw_cpus(cpu);
+ overflow = __dl_overflow(dl_b, cpus, 0, 0);
+ raw_spin_unlock_irqrestore(&dl_b->lock, flags);
- rcu_read_unlock_sched();
+ rcu_read_unlock_sched();
- if (overflow)
- return notifier_from_errno(-EBUSY);
- }
+ if (overflow)
+ return notifier_from_errno(-EBUSY);
cpuset_update_active_cpus(false);
break;
case CPU_DOWN_PREPARE_FROZEN:
queued = task_on_rq_queued(p);
if (queued)
dequeue_task(rq, p, 0);
- __setscheduler(rq, p, &attr);
+ __setscheduler(rq, p, &attr, false);
if (queued) {
enqueue_task(rq, p, 0);
resched_curr(rq);
/*
* Divide a ktime value by a nanosecond value
*/
-u64 __ktime_divns(const ktime_t kt, s64 div)
+s64 __ktime_divns(const ktime_t kt, s64 div)
{
- u64 dclc;
int sft = 0;
+ s64 dclc;
+ u64 tmp;
dclc = ktime_to_ns(kt);
+ tmp = dclc < 0 ? -dclc : dclc;
+
/* Make sure the divisor is less than 2^32: */
while (div >> 32) {
sft++;
div >>= 1;
}
- dclc >>= sft;
- do_div(dclc, (unsigned long) div);
-
- return dclc;
+ tmp >>= sft;
+ do_div(tmp, (unsigned long) div);
+ return dclc < 0 ? -tmp : tmp;
}
EXPORT_SYMBOL_GPL(__ktime_divns);
#endif /* BITS_PER_LONG >= 64 */
#define NMI_WATCHDOG_ENABLED (1 << NMI_WATCHDOG_ENABLED_BIT)
#define SOFT_WATCHDOG_ENABLED (1 << SOFT_WATCHDOG_ENABLED_BIT)
+static DEFINE_MUTEX(watchdog_proc_mutex);
+
#ifdef CONFIG_HARDLOCKUP_DETECTOR
static unsigned long __read_mostly watchdog_enabled = SOFT_WATCHDOG_ENABLED|NMI_WATCHDOG_ENABLED;
#else
{
int cpu;
- if (!watchdog_user_enabled)
- return;
+ mutex_lock(&watchdog_proc_mutex);
+
+ if (!(watchdog_enabled & NMI_WATCHDOG_ENABLED))
+ goto unlock;
get_online_cpus();
for_each_online_cpu(cpu)
watchdog_nmi_enable(cpu);
put_online_cpus();
+
+unlock:
+ mutex_unlock(&watchdog_proc_mutex);
}
void watchdog_nmi_disable_all(void)
{
int cpu;
+ mutex_lock(&watchdog_proc_mutex);
+
if (!watchdog_running)
- return;
+ goto unlock;
get_online_cpus();
for_each_online_cpu(cpu)
watchdog_nmi_disable(cpu);
put_online_cpus();
+
+unlock:
+ mutex_unlock(&watchdog_proc_mutex);
}
#else
static int watchdog_nmi_enable(unsigned int cpu) { return 0; }
}
-static DEFINE_MUTEX(watchdog_proc_mutex);
-
/*
* common function for watchdog, nmi_watchdog and soft_watchdog parameter
*
* published by the Free Software Foundation.
*/
+#include <linux/atomic.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/log2.h>
if (key && rhashtable_lookup_fast(ht, key, ht->p))
goto exit;
+ err = -E2BIG;
+ if (unlikely(rht_grow_above_max(ht, tbl)))
+ goto exit;
+
err = -EAGAIN;
if (rhashtable_check_elasticity(ht, tbl, hash) ||
rht_grow_above_100(ht, tbl))
if (params->max_size)
ht->p.max_size = rounddown_pow_of_two(params->max_size);
+ if (params->insecure_max_entries)
+ ht->p.insecure_max_entries =
+ rounddown_pow_of_two(params->insecure_max_entries);
+ else
+ ht->p.insecure_max_entries = ht->p.max_size * 2;
+
ht->p.min_size = max(ht->p.min_size, HASH_MIN_SIZE);
/* The maximum (not average) chain length grows with the
#define BYTES_PER_POINTER sizeof(void *)
/* GFP bitmask for kmemleak internal allocations */
-#define gfp_kmemleak_mask(gfp) (((gfp) & (GFP_KERNEL | GFP_ATOMIC)) | \
+#define gfp_kmemleak_mask(gfp) (((gfp) & (GFP_KERNEL | GFP_ATOMIC | \
+ __GFP_NOACCOUNT)) | \
__GFP_NORETRY | __GFP_NOMEMALLOC | \
__GFP_NOWARN)
if (numabalancing_override)
set_numabalancing_state(numabalancing_override == 1);
- if (nr_node_ids > 1 && !numabalancing_override) {
+ if (num_online_nodes() > 1 && !numabalancing_override) {
pr_info("%s automatic NUMA balancing. "
"Configure with numa_balancing= or the "
"kernel.numa_balancing sysctl",
buddy_idx = __find_buddy_index(page_idx, order);
buddy = page + (buddy_idx - page_idx);
- if (!is_migrate_isolate_page(buddy)) {
+ if (pfn_valid_within(page_to_pfn(buddy)) &&
+ !is_migrate_isolate_page(buddy)) {
__isolate_free_page(page, order);
kernel_map_pages(page, (1 << order), 1);
set_page_refcounted(page);
case NETDEV_UP:
/* Put all VLANs for this dev in the up state too. */
vlan_group_for_each_dev(grp, i, vlandev) {
- flgs = vlandev->flags;
+ flgs = dev_get_flags(vlandev);
if (flgs & IFF_UP)
continue;
{
BT_DBG("%s %p", hdev->name, hdev);
- if (!hci_dev_test_flag(hdev, HCI_UNREGISTER)) {
+ if (!hci_dev_test_flag(hdev, HCI_UNREGISTER) &&
+ test_bit(HCI_UP, &hdev->flags)) {
/* Execute vendor specific shutdown routine */
if (hdev->shutdown)
hdev->shutdown(hdev);
* state. If we were running both LE and BR/EDR inquiry
* simultaneously, and BR/EDR inquiry is already
* finished, stop discovery, otherwise BR/EDR inquiry
- * will stop discovery when finished.
+ * will stop discovery when finished. If we will resolve
+ * remote device name, do not change discovery state.
*/
- if (!test_bit(HCI_INQUIRY, &hdev->flags))
+ if (!test_bit(HCI_INQUIRY, &hdev->flags) &&
+ hdev->discovery.state != DISCOVERY_RESOLVING)
hci_discovery_set_state(hdev,
DISCOVERY_STOPPED);
} else {
err = br_ip6_multicast_add_group(br, port, &grec->grec_mca,
vid);
- if (!err)
+ if (err)
break;
}
#include <net/route.h>
#include <net/netfilter/br_netfilter.h>
-#if IS_ENABLED(CONFIG_NF_CONNTRACK)
-#include <net/netfilter/nf_conntrack.h>
-#endif
-
#include <asm/uaccess.h>
#include "br_private.h"
#ifdef CONFIG_SYSCTL
return 0;
}
-static bool dnat_took_place(const struct sk_buff *skb)
+static bool daddr_was_changed(const struct sk_buff *skb,
+ const struct nf_bridge_info *nf_bridge)
{
-#if IS_ENABLED(CONFIG_NF_CONNTRACK)
- enum ip_conntrack_info ctinfo;
- struct nf_conn *ct;
-
- ct = nf_ct_get(skb, &ctinfo);
- if (!ct || nf_ct_is_untracked(ct))
- return false;
-
- return test_bit(IPS_DST_NAT_BIT, &ct->status);
-#else
- return false;
-#endif
+ return ip_hdr(skb)->daddr != nf_bridge->ipv4_daddr;
}
/* This requires some explaining. If DNAT has taken place,
* we will need to fix up the destination Ethernet address.
+ * This is also true when SNAT takes place (for the reply direction).
*
* There are two cases to consider:
* 1. The packet was DNAT'ed to a device in the same bridge
nf_bridge->pkt_otherhost = false;
}
nf_bridge->mask ^= BRNF_NF_BRIDGE_PREROUTING;
- if (dnat_took_place(skb)) {
+ if (daddr_was_changed(skb, nf_bridge)) {
if ((err = ip_route_input(skb, iph->daddr, iph->saddr, iph->tos, dev))) {
struct in_device *in_dev = __in_dev_get_rcu(dev);
struct sk_buff *skb,
const struct nf_hook_state *state)
{
+ struct nf_bridge_info *nf_bridge;
struct net_bridge_port *p;
struct net_bridge *br;
__u32 len = nf_bridge_encap_header_len(skb);
if (!setup_pre_routing(skb))
return NF_DROP;
+ nf_bridge = nf_bridge_info_get(skb);
+ nf_bridge->ipv4_daddr = ip_hdr(skb)->daddr;
+
skb->protocol = htons(ETH_P_IP);
NF_HOOK(NFPROTO_IPV4, NF_INET_PRE_ROUTING, state->sk, skb,
netif_carrier_on(br->dev);
}
br_log_state(p);
+ rcu_read_lock();
br_ifinfo_notify(RTM_NEWLINK, p);
+ rcu_read_unlock();
spin_unlock(&br->lock);
}
return -ENOMEM;
if (tmp.num_counters >= INT_MAX / sizeof(struct ebt_counter))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
tmp.name[sizeof(tmp.name) - 1] = 0;
return -ENOMEM;
if (tmp.num_counters >= INT_MAX / sizeof(struct ebt_counter))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
memcpy(repl, &tmp, offsetof(struct ebt_replace, hook_entry));
release_sock(sk);
timeo = schedule_timeout(timeo);
lock_sock(sk);
+
+ if (sock_flag(sk, SOCK_DEAD))
+ break;
+
clear_bit(SOCK_ASYNC_WAITDATA, &sk->sk_socket->flags);
}
struct sk_buff *skb;
lock_sock(sk);
+ if (sock_flag(sk, SOCK_DEAD)) {
+ err = -ECONNRESET;
+ goto unlock;
+ }
skb = skb_dequeue(&sk->sk_receive_queue);
caif_check_flow_release(sk);
if (list_empty(&req->r_osd_item))
req->r_osd = NULL;
}
-
- list_del_init(&req->r_req_lru_item); /* can be on notarget */
ceph_osdc_put_request(req);
}
err = __map_request(osdc, req,
force_resend || force_resend_writes);
dout("__map_request returned %d\n", err);
- if (err == 0)
- continue; /* no change and no osd was specified */
if (err < 0)
continue; /* hrm! */
- if (req->r_osd == NULL) {
- dout("tid %llu maps to no valid osd\n", req->r_tid);
- needmap++; /* request a newer map */
- continue;
- }
+ if (req->r_osd == NULL || err > 0) {
+ if (req->r_osd == NULL) {
+ dout("lingering %p tid %llu maps to no osd\n",
+ req, req->r_tid);
+ /*
+ * A homeless lingering request makes
+ * no sense, as it's job is to keep
+ * a particular OSD connection open.
+ * Request a newer map and kick the
+ * request, knowing that it won't be
+ * resent until we actually get a map
+ * that can tell us where to send it.
+ */
+ needmap++;
+ }
- dout("kicking lingering %p tid %llu osd%d\n", req, req->r_tid,
- req->r_osd ? req->r_osd->o_osd : -1);
- __register_request(osdc, req);
- __unregister_linger_request(osdc, req);
+ dout("kicking lingering %p tid %llu osd%d\n", req,
+ req->r_tid, req->r_osd ? req->r_osd->o_osd : -1);
+ __register_request(osdc, req);
+ __unregister_linger_request(osdc, req);
+ }
}
reset_changed_osds(osdc);
mutex_unlock(&osdc->request_mutex);
if (__netdev_find_adj(upper_dev, dev, &upper_dev->all_adj_list.upper))
return -EBUSY;
- if (__netdev_find_adj(dev, upper_dev, &dev->all_adj_list.upper))
+ if (__netdev_find_adj(dev, upper_dev, &dev->adj_list.upper))
return -EEXIST;
if (master && netdev_master_upper_dev_get(dev))
int err;
struct ethtool_cmd cmd;
- err = __ethtool_get_settings(dev, &cmd);
+ if (!dev->ethtool_ops->get_settings)
+ return -EOPNOTSUPP;
+
+ if (copy_from_user(&cmd, useraddr, sizeof(cmd)))
+ return -EFAULT;
+
+ cmd.cmd = ETHTOOL_GSET;
+
+ err = dev->ethtool_ops->get_settings(dev, &cmd);
if (err < 0)
return err;
}
err = rtnl_net_fill(msg, NETLINK_CB(skb).portid, nlh->nlmsg_seq, 0,
- RTM_GETNSID, net, peer, -1);
+ RTM_NEWNSID, net, peer, -1);
if (err < 0)
goto err_out;
{
struct sk_buff *skb;
+ if (dev->reg_state != NETREG_REGISTERED)
+ return;
+
skb = rtmsg_ifinfo_build_skb(type, dev, change, flags);
if (skb)
rtmsg_ifinfo_send(skb, dev, flags);
return;
sock_hold(sk);
- sock_net_set(sk, get_net(&init_net));
sock_release(sk->sk_socket);
+ sock_net_set(sk, get_net(&init_net));
sock_put(sk);
}
EXPORT_SYMBOL(sk_release_kernel);
obj-y += 6lowpan/
ieee802154-y := netlink.o nl-mac.o nl-phy.o nl_policy.o core.o \
- header_ops.o sysfs.o nl802154.o
+ header_ops.o sysfs.o nl802154.o trace.o
ieee802154_socket-y := socket.o
+CFLAGS_trace.o := -I$(src)
+
ccflags-y += -D__CHECK_ENDIAN__
int rc = -ENOBUFS;
struct net_device *dev;
int type = __IEEE802154_DEV_INVALID;
+ unsigned char name_assign_type;
pr_debug("%s\n", __func__);
if (devname[nla_len(info->attrs[IEEE802154_ATTR_DEV_NAME]) - 1]
!= '\0')
return -EINVAL; /* phy name should be null-terminated */
+ name_assign_type = NET_NAME_USER;
} else {
devname = "wpan%d";
+ name_assign_type = NET_NAME_ENUM;
}
if (strlen(devname) >= IFNAMSIZ)
}
dev = rdev_add_virtual_intf_deprecated(wpan_phy_to_rdev(phy), devname,
- type);
+ name_assign_type, type);
if (IS_ERR(dev)) {
rc = PTR_ERR(dev);
goto nla_put_failure;
return rdev_add_virtual_intf(rdev,
nla_data(info->attrs[NL802154_ATTR_IFNAME]),
- type, extended_addr);
+ NET_NAME_USER, type, extended_addr);
}
static int nl802154_del_interface(struct sk_buff *skb, struct genl_info *info)
#include <net/cfg802154.h>
#include "core.h"
+#include "trace.h"
static inline struct net_device *
rdev_add_virtual_intf_deprecated(struct cfg802154_registered_device *rdev,
- const char *name, int type)
+ const char *name,
+ unsigned char name_assign_type,
+ int type)
{
return rdev->ops->add_virtual_intf_deprecated(&rdev->wpan_phy, name,
- type);
+ name_assign_type, type);
}
static inline void
static inline int
rdev_add_virtual_intf(struct cfg802154_registered_device *rdev, char *name,
+ unsigned char name_assign_type,
enum nl802154_iftype type, __le64 extended_addr)
{
- return rdev->ops->add_virtual_intf(&rdev->wpan_phy, name, type,
+ int ret;
+
+ trace_802154_rdev_add_virtual_intf(&rdev->wpan_phy, name, type,
extended_addr);
+ ret = rdev->ops->add_virtual_intf(&rdev->wpan_phy, name,
+ name_assign_type, type,
+ extended_addr);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_del_virtual_intf(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev)
{
- return rdev->ops->del_virtual_intf(&rdev->wpan_phy, wpan_dev);
+ int ret;
+
+ trace_802154_rdev_del_virtual_intf(&rdev->wpan_phy, wpan_dev);
+ ret = rdev->ops->del_virtual_intf(&rdev->wpan_phy, wpan_dev);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_channel(struct cfg802154_registered_device *rdev, u8 page, u8 channel)
{
- return rdev->ops->set_channel(&rdev->wpan_phy, page, channel);
+ int ret;
+
+ trace_802154_rdev_set_channel(&rdev->wpan_phy, page, channel);
+ ret = rdev->ops->set_channel(&rdev->wpan_phy, page, channel);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_cca_mode(struct cfg802154_registered_device *rdev,
const struct wpan_phy_cca *cca)
{
- return rdev->ops->set_cca_mode(&rdev->wpan_phy, cca);
+ int ret;
+
+ trace_802154_rdev_set_cca_mode(&rdev->wpan_phy, cca);
+ ret = rdev->ops->set_cca_mode(&rdev->wpan_phy, cca);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_pan_id(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, __le16 pan_id)
{
- return rdev->ops->set_pan_id(&rdev->wpan_phy, wpan_dev, pan_id);
+ int ret;
+
+ trace_802154_rdev_set_pan_id(&rdev->wpan_phy, wpan_dev, pan_id);
+ ret = rdev->ops->set_pan_id(&rdev->wpan_phy, wpan_dev, pan_id);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_short_addr(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, __le16 short_addr)
{
- return rdev->ops->set_short_addr(&rdev->wpan_phy, wpan_dev, short_addr);
+ int ret;
+
+ trace_802154_rdev_set_short_addr(&rdev->wpan_phy, wpan_dev, short_addr);
+ ret = rdev->ops->set_short_addr(&rdev->wpan_phy, wpan_dev, short_addr);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_backoff_exponent(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, u8 min_be, u8 max_be)
{
- return rdev->ops->set_backoff_exponent(&rdev->wpan_phy, wpan_dev,
+ int ret;
+
+ trace_802154_rdev_set_backoff_exponent(&rdev->wpan_phy, wpan_dev,
min_be, max_be);
+ ret = rdev->ops->set_backoff_exponent(&rdev->wpan_phy, wpan_dev,
+ min_be, max_be);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_max_csma_backoffs(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, u8 max_csma_backoffs)
{
- return rdev->ops->set_max_csma_backoffs(&rdev->wpan_phy, wpan_dev,
- max_csma_backoffs);
+ int ret;
+
+ trace_802154_rdev_set_csma_backoffs(&rdev->wpan_phy, wpan_dev,
+ max_csma_backoffs);
+ ret = rdev->ops->set_max_csma_backoffs(&rdev->wpan_phy, wpan_dev,
+ max_csma_backoffs);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_max_frame_retries(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, s8 max_frame_retries)
{
- return rdev->ops->set_max_frame_retries(&rdev->wpan_phy, wpan_dev,
+ int ret;
+
+ trace_802154_rdev_set_max_frame_retries(&rdev->wpan_phy, wpan_dev,
max_frame_retries);
+ ret = rdev->ops->set_max_frame_retries(&rdev->wpan_phy, wpan_dev,
+ max_frame_retries);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
static inline int
rdev_set_lbt_mode(struct cfg802154_registered_device *rdev,
struct wpan_dev *wpan_dev, bool mode)
{
- return rdev->ops->set_lbt_mode(&rdev->wpan_phy, wpan_dev, mode);
+ int ret;
+
+ trace_802154_rdev_set_lbt_mode(&rdev->wpan_phy, wpan_dev, mode);
+ ret = rdev->ops->set_lbt_mode(&rdev->wpan_phy, wpan_dev, mode);
+ trace_802154_rdev_return_int(&rdev->wpan_phy, ret);
+ return ret;
}
#endif /* __CFG802154_RDEV_OPS */
--- /dev/null
+#include <linux/module.h>
+
+#ifndef __CHECKER__
+#define CREATE_TRACE_POINTS
+#include "trace.h"
+
+#endif
--- /dev/null
+/* Based on net/wireless/tracing.h */
+
+#undef TRACE_SYSTEM
+#define TRACE_SYSTEM cfg802154
+
+#if !defined(__RDEV_CFG802154_OPS_TRACE) || defined(TRACE_HEADER_MULTI_READ)
+#define __RDEV_CFG802154_OPS_TRACE
+
+#include <linux/tracepoint.h>
+
+#include <net/cfg802154.h>
+
+#define MAXNAME 32
+#define WPAN_PHY_ENTRY __array(char, wpan_phy_name, MAXNAME)
+#define WPAN_PHY_ASSIGN strlcpy(__entry->wpan_phy_name, \
+ wpan_phy_name(wpan_phy), \
+ MAXNAME)
+#define WPAN_PHY_PR_FMT "%s"
+#define WPAN_PHY_PR_ARG __entry->wpan_phy_name
+
+#define WPAN_DEV_ENTRY __field(u32, identifier)
+#define WPAN_DEV_ASSIGN (__entry->identifier) = (!IS_ERR_OR_NULL(wpan_dev) \
+ ? wpan_dev->identifier : 0)
+#define WPAN_DEV_PR_FMT "wpan_dev(%u)"
+#define WPAN_DEV_PR_ARG (__entry->identifier)
+
+#define WPAN_CCA_ENTRY __field(enum nl802154_cca_modes, cca_mode) \
+ __field(enum nl802154_cca_opts, cca_opt)
+#define WPAN_CCA_ASSIGN \
+ do { \
+ (__entry->cca_mode) = cca->mode; \
+ (__entry->cca_opt) = cca->opt; \
+ } while (0)
+#define WPAN_CCA_PR_FMT "cca_mode: %d, cca_opt: %d"
+#define WPAN_CCA_PR_ARG __entry->cca_mode, __entry->cca_opt
+
+#define BOOL_TO_STR(bo) (bo) ? "true" : "false"
+
+/*************************************************************
+ * rdev->ops traces *
+ *************************************************************/
+
+TRACE_EVENT(802154_rdev_add_virtual_intf,
+ TP_PROTO(struct wpan_phy *wpan_phy, char *name,
+ enum nl802154_iftype type, __le64 extended_addr),
+ TP_ARGS(wpan_phy, name, type, extended_addr),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ __string(vir_intf_name, name ? name : "<noname>")
+ __field(enum nl802154_iftype, type)
+ __field(__le64, extended_addr)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ __assign_str(vir_intf_name, name ? name : "<noname>");
+ __entry->type = type;
+ __entry->extended_addr = extended_addr;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", virtual intf name: %s, type: %d, ea %llx",
+ WPAN_PHY_PR_ARG, __get_str(vir_intf_name), __entry->type,
+ __le64_to_cpu(__entry->extended_addr))
+);
+
+TRACE_EVENT(802154_rdev_del_virtual_intf,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev),
+ TP_ARGS(wpan_phy, wpan_dev),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT, WPAN_PHY_PR_ARG,
+ WPAN_DEV_PR_ARG)
+);
+
+TRACE_EVENT(802154_rdev_set_channel,
+ TP_PROTO(struct wpan_phy *wpan_phy, u8 page, u8 channel),
+ TP_ARGS(wpan_phy, page, channel),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ __field(u8, page)
+ __field(u8, channel)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ __entry->page = page;
+ __entry->channel = channel;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", page: %d, channel: %d", WPAN_PHY_PR_ARG,
+ __entry->page, __entry->channel)
+);
+
+TRACE_EVENT(802154_rdev_set_cca_mode,
+ TP_PROTO(struct wpan_phy *wpan_phy, const struct wpan_phy_cca *cca),
+ TP_ARGS(wpan_phy, cca),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_CCA_ENTRY
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_CCA_ASSIGN;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_CCA_PR_FMT, WPAN_PHY_PR_ARG,
+ WPAN_CCA_PR_ARG)
+);
+
+DECLARE_EVENT_CLASS(802154_le16_template,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ __le16 le16arg),
+ TP_ARGS(wpan_phy, wpan_dev, le16arg),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ __field(__le16, le16arg)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ __entry->le16arg = le16arg;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT ", pan id: 0x%04x",
+ WPAN_PHY_PR_ARG, WPAN_DEV_PR_ARG,
+ __le16_to_cpu(__entry->le16arg))
+);
+
+DEFINE_EVENT(802154_le16_template, 802154_rdev_set_pan_id,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ __le16 le16arg),
+ TP_ARGS(wpan_phy, wpan_dev, le16arg)
+);
+
+DEFINE_EVENT_PRINT(802154_le16_template, 802154_rdev_set_short_addr,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ __le16 le16arg),
+ TP_ARGS(wpan_phy, wpan_dev, le16arg),
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT ", sa: 0x%04x",
+ WPAN_PHY_PR_ARG, WPAN_DEV_PR_ARG,
+ __le16_to_cpu(__entry->le16arg))
+);
+
+TRACE_EVENT(802154_rdev_set_backoff_exponent,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ u8 min_be, u8 max_be),
+ TP_ARGS(wpan_phy, wpan_dev, min_be, max_be),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ __field(u8, min_be)
+ __field(u8, max_be)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ __entry->min_be = min_be;
+ __entry->max_be = max_be;
+ ),
+
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT
+ ", min be: %d, max_be: %d", WPAN_PHY_PR_ARG,
+ WPAN_DEV_PR_ARG, __entry->min_be, __entry->max_be)
+);
+
+TRACE_EVENT(802154_rdev_set_csma_backoffs,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ u8 max_csma_backoffs),
+ TP_ARGS(wpan_phy, wpan_dev, max_csma_backoffs),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ __field(u8, max_csma_backoffs)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ __entry->max_csma_backoffs = max_csma_backoffs;
+ ),
+
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT
+ ", max csma backoffs: %d", WPAN_PHY_PR_ARG,
+ WPAN_DEV_PR_ARG, __entry->max_csma_backoffs)
+);
+
+TRACE_EVENT(802154_rdev_set_max_frame_retries,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ s8 max_frame_retries),
+ TP_ARGS(wpan_phy, wpan_dev, max_frame_retries),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ __field(s8, max_frame_retries)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ __entry->max_frame_retries = max_frame_retries;
+ ),
+
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT
+ ", max frame retries: %d", WPAN_PHY_PR_ARG,
+ WPAN_DEV_PR_ARG, __entry->max_frame_retries)
+);
+
+TRACE_EVENT(802154_rdev_set_lbt_mode,
+ TP_PROTO(struct wpan_phy *wpan_phy, struct wpan_dev *wpan_dev,
+ bool mode),
+ TP_ARGS(wpan_phy, wpan_dev, mode),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ WPAN_DEV_ENTRY
+ __field(bool, mode)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ WPAN_DEV_ASSIGN;
+ __entry->mode = mode;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", " WPAN_DEV_PR_FMT
+ ", lbt mode: %s", WPAN_PHY_PR_ARG,
+ WPAN_DEV_PR_ARG, BOOL_TO_STR(__entry->mode))
+);
+
+TRACE_EVENT(802154_rdev_return_int,
+ TP_PROTO(struct wpan_phy *wpan_phy, int ret),
+ TP_ARGS(wpan_phy, ret),
+ TP_STRUCT__entry(
+ WPAN_PHY_ENTRY
+ __field(int, ret)
+ ),
+ TP_fast_assign(
+ WPAN_PHY_ASSIGN;
+ __entry->ret = ret;
+ ),
+ TP_printk(WPAN_PHY_PR_FMT ", returned: %d", WPAN_PHY_PR_ARG,
+ __entry->ret)
+);
+
+#endif /* !__RDEV_CFG802154_OPS_TRACE || TRACE_HEADER_MULTI_READ */
+
+#undef TRACE_INCLUDE_PATH
+#define TRACE_INCLUDE_PATH .
+#undef TRACE_INCLUDE_FILE
+#define TRACE_INCLUDE_FILE trace
+#include <trace/define_trace.h>
state = fa->fa_state;
new_fa->fa_state = state & ~FA_S_ACCESSED;
new_fa->fa_slen = fa->fa_slen;
+ new_fa->tb_id = tb->tb_id;
err = netdev_switch_fib_ipv4_add(key, plen, fi,
new_fa->fa_tos,
/* record local slen */
slen = fa->fa_slen;
- if (!fi || !(fi->fib_flags & RTNH_F_EXTERNAL))
+ if (!fi || !(fi->fib_flags & RTNH_F_OFFLOAD))
continue;
netdev_switch_fib_ipv4_del(n->key,
handler->idiag_get_info(sk, r, info);
if (sk->sk_state < TCP_TIME_WAIT) {
- int err = 0;
+ union tcp_cc_info info;
+ size_t sz = 0;
+ int attr;
rcu_read_lock();
ca_ops = READ_ONCE(icsk->icsk_ca_ops);
if (ca_ops && ca_ops->get_info)
- err = ca_ops->get_info(sk, ext, skb);
+ sz = ca_ops->get_info(sk, ext, &attr, &info);
rcu_read_unlock();
- if (err < 0)
+ if (sz && nla_put(skb, attr, sz, &info) < 0)
goto errout;
}
/* overflow check */
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
return -ENOMEM;
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
/* overflow check */
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
return -ENOMEM;
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
bool send;
int code;
+ /* IP on this device is disabled. */
+ if (!in_dev)
+ goto out;
+
net = dev_net(rt->dst.dev);
if (!IN_DEV_FORWARD(in_dev)) {
switch (rt->dst.error) {
#include <linux/types.h>
#include <linux/fcntl.h>
#include <linux/poll.h>
+#include <linux/inet_diag.h>
#include <linux/init.h>
#include <linux/fs.h>
#include <linux/skbuff.h>
tp->snd_ssthresh = TCP_INFINITE_SSTHRESH;
tp->snd_cwnd_clamp = ~0;
tp->mss_cache = TCP_MSS_DEFAULT;
+ u64_stats_init(&tp->syncp);
tp->reordering = sysctl_tcp_reordering;
tcp_enable_early_retrans(tp);
#endif
/* Return information about state of tcp endpoint in API format. */
-void tcp_get_info(const struct sock *sk, struct tcp_info *info)
+void tcp_get_info(struct sock *sk, struct tcp_info *info)
{
const struct tcp_sock *tp = tcp_sk(sk);
const struct inet_connection_sock *icsk = inet_csk(sk);
u32 now = tcp_time_stamp;
+ unsigned int start;
u32 rate;
memset(info, 0, sizeof(*info));
rate = READ_ONCE(sk->sk_max_pacing_rate);
info->tcpi_max_pacing_rate = rate != ~0U ? rate : ~0ULL;
+
+ do {
+ start = u64_stats_fetch_begin_irq(&tp->syncp);
+ info->tcpi_bytes_acked = tp->bytes_acked;
+ info->tcpi_bytes_received = tp->bytes_received;
+ } while (u64_stats_fetch_retry_irq(&tp->syncp, start));
}
EXPORT_SYMBOL_GPL(tcp_get_info);
return -EFAULT;
return 0;
}
+ case TCP_CC_INFO: {
+ const struct tcp_congestion_ops *ca_ops;
+ union tcp_cc_info info;
+ size_t sz = 0;
+ int attr;
+
+ if (get_user(len, optlen))
+ return -EFAULT;
+
+ ca_ops = icsk->icsk_ca_ops;
+ if (ca_ops && ca_ops->get_info)
+ sz = ca_ops->get_info(sk, ~0U, &attr, &info);
+
+ len = min_t(unsigned int, len, sz);
+ if (put_user(len, optlen))
+ return -EFAULT;
+ if (copy_to_user(optval, &info, len))
+ return -EFAULT;
+ return 0;
+ }
case TCP_QUICKACK:
val = !icsk->icsk_ack.pingpong;
break;
}
}
-static int dctcp_get_info(struct sock *sk, u32 ext, struct sk_buff *skb)
+static size_t dctcp_get_info(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info)
{
const struct dctcp *ca = inet_csk_ca(sk);
*/
if (ext & (1 << (INET_DIAG_DCTCPINFO - 1)) ||
ext & (1 << (INET_DIAG_VEGASINFO - 1))) {
- struct tcp_dctcp_info info;
-
- memset(&info, 0, sizeof(info));
+ memset(info, 0, sizeof(struct tcp_dctcp_info));
if (inet_csk(sk)->icsk_ca_ops != &dctcp_reno) {
- info.dctcp_enabled = 1;
- info.dctcp_ce_state = (u16) ca->ce_state;
- info.dctcp_alpha = ca->dctcp_alpha;
- info.dctcp_ab_ecn = ca->acked_bytes_ecn;
- info.dctcp_ab_tot = ca->acked_bytes_total;
+ info->dctcp.dctcp_enabled = 1;
+ info->dctcp.dctcp_ce_state = (u16) ca->ce_state;
+ info->dctcp.dctcp_alpha = ca->dctcp_alpha;
+ info->dctcp.dctcp_ab_ecn = ca->acked_bytes_ecn;
+ info->dctcp.dctcp_ab_tot = ca->acked_bytes_total;
}
- return nla_put(skb, INET_DIAG_DCTCPINFO, sizeof(info), &info);
+ *attr = INET_DIAG_DCTCPINFO;
+ return sizeof(*info);
}
return 0;
}
skb_set_owner_r(skb2, child);
__skb_queue_tail(&child->sk_receive_queue, skb2);
tp->syn_data_acked = 1;
+
+ /* u64_stats_update_begin(&tp->syncp) not needed here,
+ * as we certainly are not changing upper 32bit value (0)
+ */
+ tp->bytes_received = end_seq - TCP_SKB_CB(skb)->seq - 1;
} else {
end_seq = TCP_SKB_CB(skb)->seq + 1;
}
}
/* Extract info for Tcp socket info provided via netlink. */
-static int tcp_illinois_info(struct sock *sk, u32 ext, struct sk_buff *skb)
+static size_t tcp_illinois_info(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info)
{
const struct illinois *ca = inet_csk_ca(sk);
if (ext & (1 << (INET_DIAG_VEGASINFO - 1))) {
- struct tcpvegas_info info = {
- .tcpv_enabled = 1,
- .tcpv_rttcnt = ca->cnt_rtt,
- .tcpv_minrtt = ca->base_rtt,
- };
+ info->vegas.tcpv_enabled = 1;
+ info->vegas.tcpv_rttcnt = ca->cnt_rtt;
+ info->vegas.tcpv_minrtt = ca->base_rtt;
+ info->vegas.tcpv_rtt = 0;
- if (info.tcpv_rttcnt > 0) {
+ if (info->vegas.tcpv_rttcnt > 0) {
u64 t = ca->sum_rtt;
- do_div(t, info.tcpv_rttcnt);
- info.tcpv_rtt = t;
+ do_div(t, info->vegas.tcpv_rttcnt);
+ info->vegas.tcpv_rtt = t;
}
- return nla_put(skb, INET_DIAG_VEGASINFO, sizeof(info), &info);
+ *attr = INET_DIAG_VEGASINFO;
+ return sizeof(struct tcpvegas_info);
}
return 0;
}
for (j = 0; j < used_sacks; j++)
tp->recv_sack_cache[i++] = sp[j];
- tcp_mark_lost_retrans(sk);
-
- tcp_verify_left_out(tp);
-
if ((state.reord < tp->fackets_out) &&
((inet_csk(sk)->icsk_ca_state != TCP_CA_Loss) || tp->undo_marker))
tcp_update_reordering(sk, tp->fackets_out - state.reord, 0);
+ tcp_mark_lost_retrans(sk);
+ tcp_verify_left_out(tp);
out:
#if FASTRETRANS_DEBUG > 0
struct tcp_sock *tp = tcp_sk(sk);
bool recovered = !before(tp->snd_una, tp->high_seq);
+ if ((flag & FLAG_SND_UNA_ADVANCED) &&
+ tcp_try_undo_loss(sk, false))
+ return;
+
if (tp->frto) { /* F-RTO RFC5682 sec 3.1 (sack enhanced version). */
/* Step 3.b. A timeout is spurious if not all data are
* lost, i.e., never-retransmitted data are (s)acked.
*/
- if (tcp_try_undo_loss(sk, flag & FLAG_ORIG_SACK_ACKED))
+ if ((flag & FLAG_ORIG_SACK_ACKED) &&
+ tcp_try_undo_loss(sk, true))
return;
- if (after(tp->snd_nxt, tp->high_seq) &&
- (flag & FLAG_DATA_SACKED || is_dupack)) {
- tp->frto = 0; /* Loss was real: 2nd part of step 3.a */
+ if (after(tp->snd_nxt, tp->high_seq)) {
+ if (flag & FLAG_DATA_SACKED || is_dupack)
+ tp->frto = 0; /* Step 3.a. loss was real */
} else if (flag & FLAG_SND_UNA_ADVANCED && !recovered) {
tp->high_seq = tp->snd_nxt;
__tcp_push_pending_frames(sk, tcp_current_mss(sk),
else if (flag & FLAG_SND_UNA_ADVANCED)
tcp_reset_reno_sack(tp);
}
- if (tcp_try_undo_loss(sk, false))
- return;
tcp_xmit_retransmit_queue(sk);
}
(ack_seq == tp->snd_wl1 && nwin > tp->snd_wnd);
}
+/* If we update tp->snd_una, also update tp->bytes_acked */
+static void tcp_snd_una_update(struct tcp_sock *tp, u32 ack)
+{
+ u32 delta = ack - tp->snd_una;
+
+ u64_stats_update_begin(&tp->syncp);
+ tp->bytes_acked += delta;
+ u64_stats_update_end(&tp->syncp);
+ tp->snd_una = ack;
+}
+
+/* If we update tp->rcv_nxt, also update tp->bytes_received */
+static void tcp_rcv_nxt_update(struct tcp_sock *tp, u32 seq)
+{
+ u32 delta = seq - tp->rcv_nxt;
+
+ u64_stats_update_begin(&tp->syncp);
+ tp->bytes_received += delta;
+ u64_stats_update_end(&tp->syncp);
+ tp->rcv_nxt = seq;
+}
+
/* Update our send window.
*
* Window update algorithm, described in RFC793/RFC1122 (used in linux-2.2
}
}
- tp->snd_una = ack;
+ tcp_snd_una_update(tp, ack);
return flag;
}
* Note, we use the fact that SND.UNA>=SND.WL2.
*/
tcp_update_wl(tp, ack_seq);
- tp->snd_una = ack;
+ tcp_snd_una_update(tp, ack);
flag |= FLAG_WIN_UPDATE;
tcp_in_ack_event(sk, CA_ACK_WIN_UPDATE);
tail = skb_peek_tail(&sk->sk_receive_queue);
eaten = tail && tcp_try_coalesce(sk, tail, skb, &fragstolen);
- tp->rcv_nxt = TCP_SKB_CB(skb)->end_seq;
+ tcp_rcv_nxt_update(tp, TCP_SKB_CB(skb)->end_seq);
if (!eaten)
__skb_queue_tail(&sk->sk_receive_queue, skb);
if (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN)
__skb_pull(skb, hdrlen);
eaten = (tail &&
tcp_try_coalesce(sk, tail, skb, fragstolen)) ? 1 : 0;
- tcp_sk(sk)->rcv_nxt = TCP_SKB_CB(skb)->end_seq;
+ tcp_rcv_nxt_update(tcp_sk(sk), TCP_SKB_CB(skb)->end_seq);
if (!eaten) {
__skb_queue_tail(&sk->sk_receive_queue, skb);
skb_set_owner_r(skb, sk);
eaten = tcp_queue_rcv(sk, skb, 0, &fragstolen);
}
- tp->rcv_nxt = TCP_SKB_CB(skb)->end_seq;
+ tcp_rcv_nxt_update(tp, TCP_SKB_CB(skb)->end_seq);
if (skb->len)
tcp_event_data_recv(sk, skb);
if (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN)
tcp_rcv_rtt_measure_ts(sk, skb);
__skb_pull(skb, tcp_header_len);
- tp->rcv_nxt = TCP_SKB_CB(skb)->end_seq;
+ tcp_rcv_nxt_update(tp, TCP_SKB_CB(skb)->end_seq);
NET_INC_STATS_BH(sock_net(sk), LINUX_MIB_TCPHPHITSTOUSER);
eaten = 1;
}
tw->tw_v6_daddr = sk->sk_v6_daddr;
tw->tw_v6_rcv_saddr = sk->sk_v6_rcv_saddr;
tw->tw_tclass = np->tclass;
- tw->tw_flowlabel = np->flow_label >> 12;
+ tw->tw_flowlabel = be32_to_cpu(np->flow_label & IPV6_FLOWLABEL_MASK);
tw->tw_ipv6only = sk->sk_ipv6only;
}
#endif
}
/* Extract info for Tcp socket info provided via netlink. */
-int tcp_vegas_get_info(struct sock *sk, u32 ext, struct sk_buff *skb)
+size_t tcp_vegas_get_info(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info)
{
const struct vegas *ca = inet_csk_ca(sk);
+
if (ext & (1 << (INET_DIAG_VEGASINFO - 1))) {
- struct tcpvegas_info info = {
- .tcpv_enabled = ca->doing_vegas_now,
- .tcpv_rttcnt = ca->cntRTT,
- .tcpv_rtt = ca->baseRTT,
- .tcpv_minrtt = ca->minRTT,
- };
-
- return nla_put(skb, INET_DIAG_VEGASINFO, sizeof(info), &info);
+ info->vegas.tcpv_enabled = ca->doing_vegas_now,
+ info->vegas.tcpv_rttcnt = ca->cntRTT,
+ info->vegas.tcpv_rtt = ca->baseRTT,
+ info->vegas.tcpv_minrtt = ca->minRTT,
+
+ *attr = INET_DIAG_VEGASINFO;
+ return sizeof(struct tcpvegas_info);
}
return 0;
}
void tcp_vegas_state(struct sock *sk, u8 ca_state);
void tcp_vegas_pkts_acked(struct sock *sk, u32 cnt, s32 rtt_us);
void tcp_vegas_cwnd_event(struct sock *sk, enum tcp_ca_event event);
-int tcp_vegas_get_info(struct sock *sk, u32 ext, struct sk_buff *skb);
+size_t tcp_vegas_get_info(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info);
#endif /* __TCP_VEGAS_H */
}
/* Extract info for Tcp socket info provided via netlink. */
-static int tcp_westwood_info(struct sock *sk, u32 ext, struct sk_buff *skb)
+static size_t tcp_westwood_info(struct sock *sk, u32 ext, int *attr,
+ union tcp_cc_info *info)
{
const struct westwood *ca = inet_csk_ca(sk);
if (ext & (1 << (INET_DIAG_VEGASINFO - 1))) {
- struct tcpvegas_info info = {
- .tcpv_enabled = 1,
- .tcpv_rtt = jiffies_to_usecs(ca->rtt),
- .tcpv_minrtt = jiffies_to_usecs(ca->rtt_min),
- };
+ info->vegas.tcpv_enabled = 1;
+ info->vegas.tcpv_rttcnt = 0;
+ info->vegas.tcpv_rtt = jiffies_to_usecs(ca->rtt),
+ info->vegas.tcpv_minrtt = jiffies_to_usecs(ca->rtt_min),
- return nla_put(skb, INET_DIAG_VEGASINFO, sizeof(info), &info);
+ *attr = INET_DIAG_VEGASINFO;
+ return sizeof(struct tcpvegas_info);
}
return 0;
}
{
struct rt6_info *iter = NULL;
struct rt6_info **ins;
+ struct rt6_info **fallback_ins = NULL;
int replace = (info->nlh &&
(info->nlh->nlmsg_flags & NLM_F_REPLACE));
int add = (!info->nlh ||
(info->nlh->nlmsg_flags & NLM_F_EXCL))
return -EEXIST;
if (replace) {
- found++;
- break;
+ if (rt_can_ecmp == rt6_qualify_for_ecmp(iter)) {
+ found++;
+ break;
+ }
+ if (rt_can_ecmp)
+ fallback_ins = fallback_ins ?: ins;
+ goto next_iter;
}
if (iter->dst.dev == rt->dst.dev &&
if (iter->rt6i_metric > rt->rt6i_metric)
break;
+next_iter:
ins = &iter->dst.rt6_next;
}
+ if (fallback_ins && !found) {
+ /* No ECMP-able route found, replace first non-ECMP one */
+ ins = fallback_ins;
+ iter = *ins;
+ found++;
+ }
+
/* Reset round-robin state, if necessary */
if (ins == &fn->leaf)
fn->rr_ptr = NULL;
}
} else {
+ int nsiblings;
+
if (!found) {
if (add)
goto add;
info->nl_net->ipv6.rt6_stats->fib_route_nodes++;
fn->fn_flags |= RTN_RTINFO;
}
+ nsiblings = iter->rt6i_nsiblings;
fib6_purge_rt(iter, fn, info->nl_net);
rt6_release(iter);
+
+ if (nsiblings) {
+ /* Replacing an ECMP route, remove all siblings */
+ ins = &rt->dst.rt6_next;
+ iter = *ins;
+ while (iter) {
+ if (rt6_qualify_for_ecmp(iter)) {
+ *ins = iter->dst.rt6_next;
+ fib6_purge_rt(iter, fn, info->nl_net);
+ rt6_release(iter);
+ nsiblings--;
+ } else {
+ ins = &iter->dst.rt6_next;
+ }
+ iter = *ins;
+ }
+ WARN_ON(nsiblings != 0);
+ }
}
return 0;
#endif
int err;
- if (!*dst)
- *dst = ip6_route_output(net, sk, fl6);
-
- err = (*dst)->error;
- if (err)
- goto out_err_release;
+ /* The correct way to handle this would be to do
+ * ip6_route_get_saddr, and then ip6_route_output; however,
+ * the route-specific preferred source forces the
+ * ip6_route_output call _before_ ip6_route_get_saddr.
+ *
+ * In source specific routing (no src=any default route),
+ * ip6_route_output will fail given src=any saddr, though, so
+ * that's why we try it again later.
+ */
+ if (ipv6_addr_any(&fl6->saddr) && (!*dst || !(*dst)->error)) {
+ struct rt6_info *rt;
+ bool had_dst = *dst != NULL;
- if (ipv6_addr_any(&fl6->saddr)) {
- struct rt6_info *rt = (struct rt6_info *) *dst;
+ if (!had_dst)
+ *dst = ip6_route_output(net, sk, fl6);
+ rt = (*dst)->error ? NULL : (struct rt6_info *)*dst;
err = ip6_route_get_saddr(net, rt, &fl6->daddr,
sk ? inet6_sk(sk)->srcprefs : 0,
&fl6->saddr);
if (err)
goto out_err_release;
+
+ /* If we had an erroneous initial result, pretend it
+ * never existed and let the SA-enabled version take
+ * over.
+ */
+ if (!had_dst && (*dst)->error) {
+ dst_release(*dst);
+ *dst = NULL;
+ }
}
+ if (!*dst)
+ *dst = ip6_route_output(net, sk, fl6);
+
+ err = (*dst)->error;
+ if (err)
+ goto out_err_release;
+
#ifdef CONFIG_IPV6_OPTIMISTIC_DAD
/*
* Here if the dst entry we've looked up
/* If this is the first and only packet and device
* supports checksum offloading, let's use it.
+ * Use transhdrlen, same as IPv4, because partial
+ * sums only work when transhdrlen is set.
*/
- if (!skb && sk->sk_protocol == IPPROTO_UDP &&
+ if (transhdrlen && sk->sk_protocol == IPPROTO_UDP &&
length + fragheaderlen < mtu &&
rt->dst.dev->features & NETIF_F_V6_CSUM &&
!exthdrlen)
/* overflow check */
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
return -ENOMEM;
if (tmp.num_counters >= INT_MAX / sizeof(struct xt_counters))
return -ENOMEM;
+ if (tmp.num_counters == 0)
+ return -EINVAL;
+
tmp.name[sizeof(tmp.name)-1] = 0;
newinfo = xt_alloc_table_info(tmp.size);
unsigned int prefs,
struct in6_addr *saddr)
{
- struct inet6_dev *idev = ip6_dst_idev((struct dst_entry *)rt);
+ struct inet6_dev *idev =
+ rt ? ip6_dst_idev((struct dst_entry *)rt) : NULL;
int err = 0;
- if (rt->rt6i_prefsrc.plen)
+ if (rt && rt->rt6i_prefsrc.plen)
*saddr = rt->rt6i_prefsrc.addr;
else
err = ipv6_dev_get_saddr(net, idev ? idev->dev : NULL,
int attrlen;
int err = 0, last_err = 0;
+ remaining = cfg->fc_mp_len;
beginning:
rtnh = (struct rtnexthop *)cfg->fc_mp;
- remaining = cfg->fc_mp_len;
/* Parse a Multipath Entry */
while (rtnh_ok(rtnh, remaining)) {
* next hops that have been already added.
*/
add = 0;
+ remaining = cfg->fc_mp_len - remaining;
goto beginning;
}
}
/* Because each route is added like a single route we remove
- * this flag after the first nexthop (if there is a collision,
- * we have already fail to add the first nexthop:
- * fib6_add_rt2node() has reject it).
+ * these flags after the first nexthop: if there is a collision,
+ * we have already failed to add the first nexthop:
+ * fib6_add_rt2node() has rejected it; when replacing, old
+ * nexthops have been replaced by first new, the rest should
+ * be added to it.
*/
- cfg->fc_nlinfo.nlh->nlmsg_flags &= ~NLM_F_EXCL;
+ cfg->fc_nlinfo.nlh->nlmsg_flags &= ~(NLM_F_EXCL |
+ NLM_F_REPLACE);
rtnh = rtnh_next(rtnh, &remaining);
}
tcptw->tw_rcv_wnd >> tw->tw_rcv_wscale,
tcp_time_stamp + tcptw->tw_ts_offset,
tcptw->tw_ts_recent, tw->tw_bound_dev_if, tcp_twsk_md5_key(tcptw),
- tw->tw_tclass, (tw->tw_flowlabel << 12));
+ tw->tw_tclass, cpu_to_be32(tw->tw_flowlabel));
inet_twsk_put(tw);
}
(inet->inet_dport && inet->inet_dport != rmt_port) ||
(!ipv6_addr_any(&sk->sk_v6_daddr) &&
!ipv6_addr_equal(&sk->sk_v6_daddr, rmt_addr)) ||
- (sk->sk_bound_dev_if && sk->sk_bound_dev_if != dif))
+ (sk->sk_bound_dev_if && sk->sk_bound_dev_if != dif) ||
+ (!ipv6_addr_any(&sk->sk_v6_rcv_saddr) &&
+ !ipv6_addr_equal(&sk->sk_v6_rcv_saddr, loc_addr)))
return false;
if (!inet6_mc_check(sk, loc_addr, rmt_addr))
return false;
struct ieee80211_roc_work *new_roc,
struct ieee80211_roc_work *cur_roc)
{
- unsigned long j = jiffies;
- unsigned long cur_roc_end = cur_roc->hw_start_time +
- msecs_to_jiffies(cur_roc->duration);
- struct ieee80211_roc_work *next_roc;
- int new_dur;
+ unsigned long now = jiffies;
+ unsigned long remaining = cur_roc->hw_start_time +
+ msecs_to_jiffies(cur_roc->duration) -
+ now;
if (WARN_ON(!cur_roc->started || !cur_roc->hw_begun))
return false;
- if (time_after(j + IEEE80211_ROC_MIN_LEFT, cur_roc_end))
+ /* if it doesn't fit entirely, schedule a new one */
+ if (new_roc->duration > jiffies_to_msecs(remaining))
return false;
ieee80211_handle_roc_started(new_roc);
- new_dur = new_roc->duration - jiffies_to_msecs(cur_roc_end - j);
-
- /* cur_roc is long enough - add new_roc to the dependents list. */
- if (new_dur <= 0) {
- list_add_tail(&new_roc->list, &cur_roc->dependents);
- return true;
- }
-
- new_roc->duration = new_dur;
-
- /*
- * if cur_roc was already coalesced before, we might
- * want to extend the next roc instead of adding
- * a new one.
- */
- next_roc = list_entry(cur_roc->list.next,
- struct ieee80211_roc_work, list);
- if (&next_roc->list != &local->roc_list &&
- next_roc->chan == new_roc->chan &&
- next_roc->sdata == new_roc->sdata &&
- !WARN_ON(next_roc->started)) {
- list_add_tail(&new_roc->list, &next_roc->dependents);
- next_roc->duration = max(next_roc->duration,
- new_roc->duration);
- next_roc->type = max(next_roc->type, new_roc->type);
- return true;
- }
-
- /* add right after cur_roc */
- list_add(&new_roc->list, &cur_roc->list);
-
+ /* add to dependents so we send the expired event properly */
+ list_add_tail(&new_roc->list, &cur_roc->dependents);
return true;
}
* In the offloaded ROC case, if it hasn't begun, add
* this new one to the dependent list to be handled
* when the master one begins. If it has begun,
- * check that there's still a minimum time left and
- * if so, start this one, transmitting the frame, but
- * add it to the list directly after this one with
- * a reduced time so we'll ask the driver to execute
- * it right after finishing the previous one, in the
- * hope that it'll also be executed right afterwards,
- * effectively extending the old one.
- * If there's no minimum time left, just add it to the
- * normal list.
- * TODO: the ROC type is ignored here, assuming that it
- * is better to immediately use the current ROC.
+ * check if it fits entirely within the existing one,
+ * in which case it will just be dependent as well.
+ * Otherwise, schedule it by itself.
*/
if (!tmp->hw_begun) {
list_add_tail(&roc->list, &tmp->dependents);
* @IEEE80211_RX_CMNTR: received on cooked monitor already
* @IEEE80211_RX_BEACON_REPORTED: This frame was already reported
* to cfg80211_report_obss_beacon().
+ * @IEEE80211_RX_REORDER_TIMER: this frame is released by the
+ * reorder buffer timeout timer, not the normal RX path
*
* These flags are used across handling multiple interfaces
* for a single frame.
enum ieee80211_rx_flags {
IEEE80211_RX_CMNTR = BIT(0),
IEEE80211_RX_BEACON_REPORTED = BIT(1),
+ IEEE80211_RX_REORDER_TIMER = BIT(2),
};
struct ieee80211_rx_data {
u8 flags;
};
-#if HZ/100 == 0
-#define IEEE80211_ROC_MIN_LEFT 1
-#else
-#define IEEE80211_ROC_MIN_LEFT (HZ/100)
-#endif
-
struct ieee80211_roc_work {
struct list_head list;
struct list_head dependents;
memcpy(sdata->vif.hw_queue, master->vif.hw_queue,
sizeof(sdata->vif.hw_queue));
sdata->vif.bss_conf.chandef = master->vif.bss_conf.chandef;
+
+ mutex_lock(&local->key_mtx);
+ sdata->crypto_tx_tailroom_needed_cnt +=
+ master->crypto_tx_tailroom_needed_cnt;
+ mutex_unlock(&local->key_mtx);
+
break;
}
case NL80211_IFTYPE_AP:
* (because if we remove a STA after ops->remove_interface()
* the driver will have removed the vif info already!)
*
- * This is relevant only in WDS mode, in all other modes we've
- * already removed all stations when disconnecting or similar,
- * so warn otherwise.
+ * In WDS mode a station must exist here and be flushed, for
+ * AP_VLANs stations may exist since there's nothing else that
+ * would have removed them, but in other modes there shouldn't
+ * be any stations.
*/
flushed = sta_info_flush(sdata);
- WARN_ON_ONCE((sdata->vif.type != NL80211_IFTYPE_WDS && flushed > 0) ||
- (sdata->vif.type == NL80211_IFTYPE_WDS && flushed != 1));
+ WARN_ON_ONCE(sdata->vif.type != NL80211_IFTYPE_AP_VLAN &&
+ ((sdata->vif.type != NL80211_IFTYPE_WDS && flushed > 0) ||
+ (sdata->vif.type == NL80211_IFTYPE_WDS && flushed != 1)));
/* don't count this interface for promisc/allmulti while it is down */
if (sdata->flags & IEEE80211_SDATA_ALLMULTI)
lockdep_assert_held(&local->key_mtx);
}
+static void
+update_vlan_tailroom_need_count(struct ieee80211_sub_if_data *sdata, int delta)
+{
+ struct ieee80211_sub_if_data *vlan;
+
+ if (sdata->vif.type != NL80211_IFTYPE_AP)
+ return;
+
+ mutex_lock(&sdata->local->mtx);
+
+ list_for_each_entry(vlan, &sdata->u.ap.vlans, u.vlan.list)
+ vlan->crypto_tx_tailroom_needed_cnt += delta;
+
+ mutex_unlock(&sdata->local->mtx);
+}
+
static void increment_tailroom_need_count(struct ieee80211_sub_if_data *sdata)
{
/*
* http://mid.gmane.org/1308590980.4322.19.camel@jlt3.sipsolutions.net
*/
+ update_vlan_tailroom_need_count(sdata, 1);
+
if (!sdata->crypto_tx_tailroom_needed_cnt++) {
/*
* Flush all XMIT packets currently using HW encryption or no
}
}
+static void decrease_tailroom_need_count(struct ieee80211_sub_if_data *sdata,
+ int delta)
+{
+ WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt < delta);
+
+ update_vlan_tailroom_need_count(sdata, -delta);
+ sdata->crypto_tx_tailroom_needed_cnt -= delta;
+}
+
static int ieee80211_key_enable_hw_accel(struct ieee80211_key *key)
{
struct ieee80211_sub_if_data *sdata;
if (!((key->conf.flags & IEEE80211_KEY_FLAG_GENERATE_MMIC) ||
(key->conf.flags & IEEE80211_KEY_FLAG_RESERVE_TAILROOM)))
- sdata->crypto_tx_tailroom_needed_cnt--;
+ decrease_tailroom_need_count(sdata, 1);
WARN_ON((key->conf.flags & IEEE80211_KEY_FLAG_PUT_IV_SPACE) &&
(key->conf.flags & IEEE80211_KEY_FLAG_GENERATE_IV));
schedule_delayed_work(&sdata->dec_tailroom_needed_wk,
HZ/2);
} else {
- sdata->crypto_tx_tailroom_needed_cnt--;
+ decrease_tailroom_need_count(sdata, 1);
}
}
void ieee80211_enable_keys(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_key *key;
+ struct ieee80211_sub_if_data *vlan;
ASSERT_RTNL();
mutex_lock(&sdata->local->key_mtx);
- sdata->crypto_tx_tailroom_needed_cnt = 0;
+ WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
+ sdata->crypto_tx_tailroom_pending_dec);
+
+ if (sdata->vif.type == NL80211_IFTYPE_AP) {
+ list_for_each_entry(vlan, &sdata->u.ap.vlans, u.vlan.list)
+ WARN_ON_ONCE(vlan->crypto_tx_tailroom_needed_cnt ||
+ vlan->crypto_tx_tailroom_pending_dec);
+ }
list_for_each_entry(key, &sdata->key_list, list) {
increment_tailroom_need_count(sdata);
mutex_unlock(&sdata->local->key_mtx);
}
+void ieee80211_reset_crypto_tx_tailroom(struct ieee80211_sub_if_data *sdata)
+{
+ struct ieee80211_sub_if_data *vlan;
+
+ mutex_lock(&sdata->local->key_mtx);
+
+ sdata->crypto_tx_tailroom_needed_cnt = 0;
+
+ if (sdata->vif.type == NL80211_IFTYPE_AP) {
+ list_for_each_entry(vlan, &sdata->u.ap.vlans, u.vlan.list)
+ vlan->crypto_tx_tailroom_needed_cnt = 0;
+ }
+
+ mutex_unlock(&sdata->local->key_mtx);
+}
+
void ieee80211_iter_keys(struct ieee80211_hw *hw,
struct ieee80211_vif *vif,
void (*iter)(struct ieee80211_hw *hw,
{
struct ieee80211_key *key, *tmp;
- sdata->crypto_tx_tailroom_needed_cnt -=
- sdata->crypto_tx_tailroom_pending_dec;
+ decrease_tailroom_need_count(sdata,
+ sdata->crypto_tx_tailroom_pending_dec);
sdata->crypto_tx_tailroom_pending_dec = 0;
ieee80211_debugfs_key_remove_mgmt_default(sdata);
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_sub_if_data *vlan;
+ struct ieee80211_sub_if_data *master;
struct ieee80211_key *key, *tmp;
LIST_HEAD(keys);
list_for_each_entry_safe(key, tmp, &keys, list)
__ieee80211_key_destroy(key, false);
- WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
- sdata->crypto_tx_tailroom_pending_dec);
+ if (sdata->vif.type == NL80211_IFTYPE_AP_VLAN) {
+ if (sdata->bss) {
+ master = container_of(sdata->bss,
+ struct ieee80211_sub_if_data,
+ u.ap);
+
+ WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt !=
+ master->crypto_tx_tailroom_needed_cnt);
+ }
+ } else {
+ WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
+ sdata->crypto_tx_tailroom_pending_dec);
+ }
+
if (sdata->vif.type == NL80211_IFTYPE_AP) {
list_for_each_entry(vlan, &sdata->u.ap.vlans, u.vlan.list)
WARN_ON_ONCE(vlan->crypto_tx_tailroom_needed_cnt ||
*/
mutex_lock(&sdata->local->key_mtx);
- sdata->crypto_tx_tailroom_needed_cnt -=
- sdata->crypto_tx_tailroom_pending_dec;
+ decrease_tailroom_need_count(sdata,
+ sdata->crypto_tx_tailroom_pending_dec);
sdata->crypto_tx_tailroom_pending_dec = 0;
mutex_unlock(&sdata->local->key_mtx);
}
void ieee80211_free_sta_keys(struct ieee80211_local *local,
struct sta_info *sta);
void ieee80211_enable_keys(struct ieee80211_sub_if_data *sdata);
+void ieee80211_reset_crypto_tx_tailroom(struct ieee80211_sub_if_data *sdata);
#define key_mtx_dereference(local, ref) \
rcu_dereference_protected(ref, lockdep_is_held(&((local)->key_mtx)))
/* deliver to local stack */
skb->protocol = eth_type_trans(skb, dev);
memset(skb->cb, 0, sizeof(skb->cb));
- if (rx->local->napi)
+ if (!(rx->flags & IEEE80211_RX_REORDER_TIMER) &&
+ rx->local->napi)
napi_gro_receive(rx->local->napi, skb);
else
netif_receive_skb(skb);
/* This is OK -- must be QoS data frame */
.security_idx = tid,
.seqno_idx = tid,
- .flags = 0,
+ .flags = IEEE80211_RX_REORDER_TIMER,
};
struct tid_ampdu_rx *tid_agg_rx;
static const struct rhashtable_params sta_rht_params = {
.nelem_hint = 3, /* start small */
+ .automatic_shrinking = true,
.head_offset = offsetof(struct sta_info, hash_node),
.key_offset = offsetof(struct sta_info, sta.addr),
.key_len = ETH_ALEN,
const u8 *addr)
{
struct ieee80211_local *local = sdata->local;
+ struct sta_info *sta;
+ struct rhash_head *tmp;
+ const struct bucket_table *tbl;
+
+ rcu_read_lock();
+ tbl = rht_dereference_rcu(local->sta_hash.tbl, &local->sta_hash);
- return rhashtable_lookup_fast(&local->sta_hash, addr, sta_rht_params);
+ for_each_sta_info(local, tbl, addr, sta, tmp) {
+ if (sta->sdata == sdata) {
+ rcu_read_unlock();
+ /* this is safe as the caller must already hold
+ * another rcu read section or the mutex
+ */
+ return sta;
+ }
+ }
+ rcu_read_unlock();
+ return NULL;
}
/*
mutex_unlock(&local->sta_mtx);
/* add back keys */
+ list_for_each_entry(sdata, &local->interfaces, list)
+ ieee80211_reset_crypto_tx_tailroom(sdata);
+
list_for_each_entry(sdata, &local->interfaces, list)
if (ieee80211_sdata_running(sdata))
ieee80211_enable_keys(sdata);
hdr->frame_control |= cpu_to_le16(IEEE80211_FCTL_PROTECTED);
- if (WARN_ON(skb_tailroom(skb) < IEEE80211_WEP_ICV_LEN ||
- skb_headroom(skb) < IEEE80211_WEP_IV_LEN))
+ if (WARN_ON(skb_headroom(skb) < IEEE80211_WEP_IV_LEN))
return NULL;
hdrlen = ieee80211_hdrlen(hdr->frame_control);
size_t len;
u8 rc4key[3 + WLAN_KEY_LEN_WEP104];
+ if (WARN_ON(skb_tailroom(skb) < IEEE80211_WEP_ICV_LEN))
+ return -1;
+
iv = ieee80211_wep_add_iv(local, skb, keylen, keyidx);
if (!iv)
return -1;
static struct net_device *
ieee802154_add_iface_deprecated(struct wpan_phy *wpan_phy,
- const char *name, int type)
+ const char *name,
+ unsigned char name_assign_type, int type)
{
struct ieee802154_local *local = wpan_phy_priv(wpan_phy);
struct net_device *dev;
rtnl_lock();
- dev = ieee802154_if_add(local, name, type,
+ dev = ieee802154_if_add(local, name, name_assign_type, type,
cpu_to_le64(0x0000000000000000ULL));
rtnl_unlock();
static int
ieee802154_add_iface(struct wpan_phy *phy, const char *name,
+ unsigned char name_assign_type,
enum nl802154_iftype type, __le64 extended_addr)
{
struct ieee802154_local *local = wpan_phy_priv(phy);
struct net_device *err;
- err = ieee802154_if_add(local, name, type, extended_addr);
+ err = ieee802154_if_add(local, name, name_assign_type, type,
+ extended_addr);
return PTR_ERR_OR_ZERO(err);
}
void ieee802154_if_remove(struct ieee802154_sub_if_data *sdata);
struct net_device *
ieee802154_if_add(struct ieee802154_local *local, const char *name,
- enum nl802154_iftype type, __le64 extended_addr);
+ unsigned char name_assign_type, enum nl802154_iftype type,
+ __le64 extended_addr);
void ieee802154_remove_interfaces(struct ieee802154_local *local);
#endif /* __IEEE802154_I_H */
struct net_device *
ieee802154_if_add(struct ieee802154_local *local, const char *name,
- enum nl802154_iftype type, __le64 extended_addr)
+ unsigned char name_assign_type, enum nl802154_iftype type,
+ __le64 extended_addr)
{
struct net_device *ndev = NULL;
struct ieee802154_sub_if_data *sdata = NULL;
ASSERT_RTNL();
ndev = alloc_netdev(sizeof(*sdata) + local->hw.vif_data_size, name,
- NET_NAME_UNKNOWN, ieee802154_if_setup);
+ name_assign_type, ieee802154_if_setup);
if (!ndev)
return ERR_PTR(-ENOMEM);
for (i = 0; i < ARRAY_SIZE(key->tfm); i++) {
key->tfm[i] = crypto_alloc_aead("ccm(aes)", 0,
CRYPTO_ALG_ASYNC);
- if (!key->tfm[i])
+ if (IS_ERR(key->tfm[i]))
goto err_tfm;
if (crypto_aead_setkey(key->tfm[i], template->key,
IEEE802154_LLSEC_KEY_SIZE))
}
key->tfm0 = crypto_alloc_blkcipher("ctr(aes)", 0, CRYPTO_ALG_ASYNC);
- if (!key->tfm0)
+ if (IS_ERR(key->tfm0))
goto err_tfm;
if (crypto_blkcipher_setkey(key->tfm0, template->key,
rtnl_lock();
- dev = ieee802154_if_add(local, "wpan%d", NL802154_IFTYPE_NODE,
+ dev = ieee802154_if_add(local, "wpan%d", NET_NAME_ENUM,
+ NL802154_IFTYPE_NODE,
cpu_to_le64(0x0000000000000000ULL));
if (IS_ERR(dev)) {
rtnl_unlock();
rc = PTR_ERR(dev);
- goto out_wq;
+ goto out_phy;
}
rtnl_unlock();
return 0;
+out_phy:
+ wpan_phy_unregister(local->phy);
out_wq:
destroy_workqueue(local->workqueue);
out:
return -EINVAL;
switch (dec.label) {
- case LABEL_IMPLICIT_NULL:
+ case MPLS_LABEL_IMPLNULL:
/* RFC3032: This is a label that an LSR may
* assign and distribute, but which never
* actually appears in the encapsulation.
}
/* In case the predefined labels need to be populated */
- if (limit > LABEL_IPV4_EXPLICIT_NULL) {
+ if (limit > MPLS_LABEL_IPV4NULL) {
struct net_device *lo = net->loopback_dev;
rt0 = mpls_rt_alloc(lo->addr_len);
if (!rt0)
rt0->rt_via_table = NEIGH_LINK_TABLE;
memcpy(rt0->rt_via, lo->dev_addr, lo->addr_len);
}
- if (limit > LABEL_IPV6_EXPLICIT_NULL) {
+ if (limit > MPLS_LABEL_IPV6NULL) {
struct net_device *lo = net->loopback_dev;
rt2 = mpls_rt_alloc(lo->addr_len);
if (!rt2)
memcpy(labels, old, cp_size);
/* If needed set the predefined labels */
- if ((old_limit <= LABEL_IPV6_EXPLICIT_NULL) &&
- (limit > LABEL_IPV6_EXPLICIT_NULL)) {
- RCU_INIT_POINTER(labels[LABEL_IPV6_EXPLICIT_NULL], rt2);
+ if ((old_limit <= MPLS_LABEL_IPV6NULL) &&
+ (limit > MPLS_LABEL_IPV6NULL)) {
+ RCU_INIT_POINTER(labels[MPLS_LABEL_IPV6NULL], rt2);
rt2 = NULL;
}
- if ((old_limit <= LABEL_IPV4_EXPLICIT_NULL) &&
- (limit > LABEL_IPV4_EXPLICIT_NULL)) {
- RCU_INIT_POINTER(labels[LABEL_IPV4_EXPLICIT_NULL], rt0);
+ if ((old_limit <= MPLS_LABEL_IPV4NULL) &&
+ (limit > MPLS_LABEL_IPV4NULL)) {
+ RCU_INIT_POINTER(labels[MPLS_LABEL_IPV4NULL], rt0);
rt0 = NULL;
}
#ifndef MPLS_INTERNAL_H
#define MPLS_INTERNAL_H
-#define LABEL_IPV4_EXPLICIT_NULL 0 /* RFC3032 */
-#define LABEL_ROUTER_ALERT_LABEL 1 /* RFC3032 */
-#define LABEL_IPV6_EXPLICIT_NULL 2 /* RFC3032 */
-#define LABEL_IMPLICIT_NULL 3 /* RFC3032 */
-#define LABEL_ENTROPY_INDICATOR 7 /* RFC6790 */
-#define LABEL_GAL 13 /* RFC5586 */
-#define LABEL_OAM_ALERT 14 /* RFC3429 */
-#define LABEL_EXTENSION 15 /* RFC7274 */
-
-
struct mpls_shim_hdr {
__be32 label_stack_entry;
};
depends on NETFILTER_XTABLES
depends on NETFILTER_ADVANCED
depends on (IPV6 || IPV6=n)
+ depends on (IP6_NF_IPTABLES || IP6_NF_IPTABLES=n)
depends on IP_NF_MANGLE
select NF_DEFRAG_IPV4
select NF_DEFRAG_IPV6 if IP6_NF_IPTABLES
depends on NETFILTER_ADVANCED
depends on !NF_CONNTRACK || NF_CONNTRACK
depends on (IPV6 || IPV6=n)
+ depends on (IP6_NF_IPTABLES || IP6_NF_IPTABLES=n)
select NF_DEFRAG_IPV4
select NF_DEFRAG_IPV6 if IP6_NF_IPTABLES
help
cancel_work_sync(&ipvs->defense_work.work);
unregister_net_sysctl_table(ipvs->sysctl_hdr);
ip_vs_stop_estimator(net, &ipvs->tot_stats);
+
+ if (!net_eq(net, &init_net))
+ kfree(ipvs->sysctl_tbl);
}
#else
* sES -> sES :-)
* sFW -> sCW Normal close request answered by ACK.
* sCW -> sCW
- * sLA -> sTW Last ACK detected.
+ * sLA -> sTW Last ACK detected (RFC5961 challenged)
* sTW -> sTW Retransmitted last ACK. Remain in the same state.
* sCL -> sCL
*/
* sES -> sES :-)
* sFW -> sCW Normal close request answered by ACK.
* sCW -> sCW
- * sLA -> sTW Last ACK detected.
+ * sLA -> sTW Last ACK detected (RFC5961 challenged)
* sTW -> sTW Retransmitted last ACK.
* sCL -> sCL
*/
1 : ct->proto.tcp.last_win;
ct->proto.tcp.seen[ct->proto.tcp.last_dir].td_scale =
ct->proto.tcp.last_wscale;
+ ct->proto.tcp.last_flags &= ~IP_CT_EXP_CHALLENGE_ACK;
ct->proto.tcp.seen[ct->proto.tcp.last_dir].flags =
ct->proto.tcp.last_flags;
memset(&ct->proto.tcp.seen[dir], 0,
* may be in sync but we are not. In that case, we annotate
* the TCP options and let the packet go through. If it is a
* valid SYN packet, the server will reply with a SYN/ACK, and
- * then we'll get in sync. Otherwise, the server ignores it. */
+ * then we'll get in sync. Otherwise, the server potentially
+ * responds with a challenge ACK if implementing RFC5961.
+ */
if (index == TCP_SYN_SET && dir == IP_CT_DIR_ORIGINAL) {
struct ip_ct_tcp_state seen = {};
ct->proto.tcp.last_flags |=
IP_CT_TCP_FLAG_SACK_PERM;
}
+ /* Mark the potential for RFC5961 challenge ACK,
+ * this pose a special problem for LAST_ACK state
+ * as ACK is intrepretated as ACKing last FIN.
+ */
+ if (old_state == TCP_CONNTRACK_LAST_ACK)
+ ct->proto.tcp.last_flags |=
+ IP_CT_EXP_CHALLENGE_ACK;
}
spin_unlock_bh(&ct->lock);
if (LOG_INVALID(net, IPPROTO_TCP))
nf_log_packet(net, pf, 0, skb, NULL, NULL, NULL,
"nf_ct_tcp: invalid state ");
return -NF_ACCEPT;
+ case TCP_CONNTRACK_TIME_WAIT:
+ /* RFC5961 compliance cause stack to send "challenge-ACK"
+ * e.g. in response to spurious SYNs. Conntrack MUST
+ * not believe this ACK is acking last FIN.
+ */
+ if (old_state == TCP_CONNTRACK_LAST_ACK &&
+ index == TCP_ACK_SET &&
+ ct->proto.tcp.last_dir != dir &&
+ ct->proto.tcp.last_index == TCP_SYN_SET &&
+ (ct->proto.tcp.last_flags & IP_CT_EXP_CHALLENGE_ACK)) {
+ /* Detected RFC5961 challenge ACK */
+ ct->proto.tcp.last_flags &= ~IP_CT_EXP_CHALLENGE_ACK;
+ spin_unlock_bh(&ct->lock);
+ if (LOG_INVALID(net, IPPROTO_TCP))
+ nf_log_packet(net, pf, 0, skb, NULL, NULL, NULL,
+ "nf_ct_tcp: challenge-ACK ignored ");
+ return NF_ACCEPT; /* Don't change state */
+ }
+ break;
case TCP_CONNTRACK_CLOSE:
if (index == TCP_RST_SET
&& (ct->proto.tcp.seen[!dir].flags & IP_CT_TCP_FLAG_MAXACK_SET)
*/
void nft_data_uninit(const struct nft_data *data, enum nft_data_types type)
{
- switch (type) {
- case NFT_DATA_VALUE:
+ if (type < NFT_DATA_VERDICT)
return;
+ switch (type) {
case NFT_DATA_VERDICT:
return nft_verdict_uninit(data);
default:
static int __init nfnetlink_log_init(void)
{
- int status = -ENOMEM;
+ int status;
+
+ status = register_pernet_subsys(&nfnl_log_net_ops);
+ if (status < 0) {
+ pr_err("failed to register pernet ops\n");
+ goto out;
+ }
netlink_register_notifier(&nfulnl_rtnl_notifier);
status = nfnetlink_subsys_register(&nfulnl_subsys);
goto cleanup_subsys;
}
- status = register_pernet_subsys(&nfnl_log_net_ops);
- if (status < 0) {
- pr_err("failed to register pernet ops\n");
- goto cleanup_logger;
- }
return status;
-cleanup_logger:
- nf_log_unregister(&nfulnl_logger);
cleanup_subsys:
nfnetlink_subsys_unregister(&nfulnl_subsys);
cleanup_netlink_notifier:
netlink_unregister_notifier(&nfulnl_rtnl_notifier);
+ unregister_pernet_subsys(&nfnl_log_net_ops);
+out:
return status;
}
static void __exit nfnetlink_log_fini(void)
{
- unregister_pernet_subsys(&nfnl_log_net_ops);
nf_log_unregister(&nfulnl_logger);
nfnetlink_subsys_unregister(&nfulnl_subsys);
netlink_unregister_notifier(&nfulnl_rtnl_notifier);
+ unregister_pernet_subsys(&nfnl_log_net_ops);
}
MODULE_DESCRIPTION("netfilter userspace logging");
static int __init nfnetlink_queue_init(void)
{
- int status = -ENOMEM;
+ int status;
+
+ status = register_pernet_subsys(&nfnl_queue_net_ops);
+ if (status < 0) {
+ pr_err("nf_queue: failed to register pernet ops\n");
+ goto out;
+ }
netlink_register_notifier(&nfqnl_rtnl_notifier);
status = nfnetlink_subsys_register(&nfqnl_subsys);
goto cleanup_netlink_notifier;
}
- status = register_pernet_subsys(&nfnl_queue_net_ops);
- if (status < 0) {
- pr_err("nf_queue: failed to register pernet ops\n");
- goto cleanup_subsys;
- }
register_netdevice_notifier(&nfqnl_dev_notifier);
nf_register_queue_handler(&nfqh);
return status;
-cleanup_subsys:
- nfnetlink_subsys_unregister(&nfqnl_subsys);
cleanup_netlink_notifier:
netlink_unregister_notifier(&nfqnl_rtnl_notifier);
+out:
return status;
}
{
nf_unregister_queue_handler();
unregister_netdevice_notifier(&nfqnl_dev_notifier);
- unregister_pernet_subsys(&nfnl_queue_net_ops);
nfnetlink_subsys_unregister(&nfqnl_subsys);
netlink_unregister_notifier(&nfqnl_rtnl_notifier);
+ unregister_pernet_subsys(&nfnl_queue_net_ops);
rcu_barrier(); /* Wait for completion of call_rcu()'s */
}
return nlk_sk(sk)->flags & NETLINK_KERNEL_SOCKET;
}
-struct netlink_table *nl_table;
+struct netlink_table *nl_table __read_mostly;
EXPORT_SYMBOL_GPL(nl_table);
static DECLARE_WAIT_QUEUE_HEAD(nl_table_wait);
if (err) {
if (err == -EEXIST)
err = -EADDRINUSE;
+ nlk_sk(sk)->portid = 0;
sock_put(sk);
}
.key_len = netlink_compare_arg_len,
.obj_hashfn = netlink_hash,
.obj_cmpfn = netlink_compare,
- .max_size = 65536,
.automatic_shrinking = true,
};
tlen = dev->needed_tailroom;
skb = sock_alloc_send_skb(&po->sk,
hlen + tlen + sizeof(struct sockaddr_ll),
- 0, &err);
+ !need_wait, &err);
- if (unlikely(skb == NULL))
+ if (unlikely(skb == NULL)) {
+ /* we assume the socket was initially writeable ... */
+ if (likely(len_sum > 0))
+ err = len_sum;
goto out_status;
-
+ }
tp_len = tpacket_fill_skb(po, skb, ph, dev, size_max, proto,
addr, hlen);
if (tp_len > dev->mtu + dev->hard_header_len) {
struct rds_transport *loop_trans;
unsigned long flags;
int ret;
+ struct rds_transport *otrans = trans;
+ if (!is_outgoing && otrans->t_type == RDS_TRANS_TCP)
+ goto new_conn;
rcu_read_lock();
conn = rds_conn_lookup(head, laddr, faddr, trans);
if (conn && conn->c_loopback && conn->c_trans != &rds_loop_transport &&
if (conn)
goto out;
+new_conn:
conn = kmem_cache_zalloc(rds_conn_slab, gfp);
if (!conn) {
conn = ERR_PTR(-ENOMEM);
/* Creating normal conn */
struct rds_connection *found;
- found = rds_conn_lookup(head, laddr, faddr, trans);
+ if (!is_outgoing && otrans->t_type == RDS_TRANS_TCP)
+ found = NULL;
+ else
+ found = rds_conn_lookup(head, laddr, faddr, trans);
if (found) {
trans->conn_free(conn->c_transport_data);
kmem_cache_free(rds_conn_slab, conn);
conn = found;
} else {
- hlist_add_head_rcu(&conn->c_hash_node, head);
+ if ((is_outgoing && otrans->t_type == RDS_TRANS_TCP) ||
+ (otrans->t_type != RDS_TRANS_TCP)) {
+ /* Only the active side should be added to
+ * reconnect list for TCP.
+ */
+ hlist_add_head_rcu(&conn->c_hash_node, head);
+ }
rds_cong_add_conn(conn);
rds_conn_count++;
}
/* If the peer gave us the last packet it saw, process this as if
* we had received a regular ACK. */
- if (dp && dp->dp_ack_seq)
- rds_send_drop_acked(conn, be64_to_cpu(dp->dp_ack_seq), NULL);
+ if (dp) {
+ /* dp structure start is not guaranteed to be 8 bytes aligned.
+ * Since dp_ack_seq is 64-bit extended load operations can be
+ * used so go through get_unaligned to avoid unaligned errors.
+ */
+ __be64 dp_ack_seq = get_unaligned(&dp->dp_ack_seq);
+
+ if (dp_ack_seq)
+ rds_send_drop_acked(conn, be64_to_cpu(dp_ack_seq),
+ NULL);
+ }
rds_connect_complete(conn);
}
case TCP_ESTABLISHED:
rds_connect_complete(conn);
break;
+ case TCP_CLOSE_WAIT:
case TCP_CLOSE:
rds_conn_drop(conn);
default:
static DECLARE_WORK(rds_tcp_listen_work, rds_tcp_accept_worker);
static struct socket *rds_tcp_listen_sock;
+static int rds_tcp_keepalive(struct socket *sock)
+{
+ /* values below based on xs_udp_default_timeout */
+ int keepidle = 5; /* send a probe 'keepidle' secs after last data */
+ int keepcnt = 5; /* number of unack'ed probes before declaring dead */
+ int keepalive = 1;
+ int ret = 0;
+
+ ret = kernel_setsockopt(sock, SOL_SOCKET, SO_KEEPALIVE,
+ (char *)&keepalive, sizeof(keepalive));
+ if (ret < 0)
+ goto bail;
+
+ ret = kernel_setsockopt(sock, IPPROTO_TCP, TCP_KEEPCNT,
+ (char *)&keepcnt, sizeof(keepcnt));
+ if (ret < 0)
+ goto bail;
+
+ ret = kernel_setsockopt(sock, IPPROTO_TCP, TCP_KEEPIDLE,
+ (char *)&keepidle, sizeof(keepidle));
+ if (ret < 0)
+ goto bail;
+
+ /* KEEPINTVL is the interval between successive probes. We follow
+ * the model in xs_tcp_finish_connecting() and re-use keepidle.
+ */
+ ret = kernel_setsockopt(sock, IPPROTO_TCP, TCP_KEEPINTVL,
+ (char *)&keepidle, sizeof(keepidle));
+bail:
+ return ret;
+}
+
static int rds_tcp_accept_one(struct socket *sock)
{
struct socket *new_sock = NULL;
struct rds_connection *conn;
int ret;
struct inet_sock *inet;
+ struct rds_tcp_connection *rs_tcp;
ret = sock_create_lite(sock->sk->sk_family, sock->sk->sk_type,
sock->sk->sk_protocol, &new_sock);
if (ret < 0)
goto out;
+ ret = rds_tcp_keepalive(new_sock);
+ if (ret < 0)
+ goto out;
+
rds_tcp_tune(new_sock);
inet = inet_sk(new_sock->sk);
ret = PTR_ERR(conn);
goto out;
}
+ /* An incoming SYN request came in, and TCP just accepted it.
+ * We always create a new conn for listen side of TCP, and do not
+ * add it to the c_hash_list.
+ *
+ * If the client reboots, this conn will need to be cleaned up.
+ * rds_tcp_state_change() will do that cleanup
+ */
+ rs_tcp = (struct rds_tcp_connection *)conn->c_transport_data;
+ WARN_ON(!rs_tcp || rs_tcp->t_sock);
/*
* see the comment above rds_queue_delayed_reconnect()
struct tcf_proto_ops *t;
int rc = -ENOENT;
+ /* Wait for outstanding call_rcu()s, if any, from a
+ * tcf_proto_ops's destroy() handler.
+ */
+ rcu_barrier();
+
write_lock(&cls_mod_lock);
list_for_each_entry(t, &tcf_proto_base, head) {
if (t == ops) {
case RTM_DELTFILTER:
err = tp->ops->delete(tp, fh);
if (err == 0) {
- tfilter_notify(net, skb, n, tp, fh, RTM_DELTFILTER);
- if (tcf_destroy(tp, false)) {
- struct tcf_proto *next = rtnl_dereference(tp->next);
+ struct tcf_proto *next = rtnl_dereference(tp->next);
+ tfilter_notify(net, skb, n, tp, fh, RTM_DELTFILTER);
+ if (tcf_destroy(tp, false))
RCU_INIT_POINTER(*back, next);
- }
}
goto errout;
case RTM_GETTFILTER:
if (dev->flags & IFF_UP)
dev_deactivate(dev);
- if (new && new->ops->attach) {
- new->ops->attach(new);
- num_q = 0;
- }
+ if (new && new->ops->attach)
+ goto skip;
for (i = 0; i < num_q; i++) {
struct netdev_queue *dev_queue = dev_ingress_queue(dev);
qdisc_destroy(old);
}
+skip:
if (!ingress) {
notify_and_destroy(net, skb, n, classid,
dev->qdisc, new);
if (new && !new->ops->attach)
atomic_inc(&new->refcnt);
dev->qdisc = new ? : &noop_qdisc;
+
+ if (new && new->ops->attach)
+ new->ops->attach(new);
} else {
notify_and_destroy(net, skb, n, classid, old, new);
}
sch->limit = DEFAULT_CODEL_LIMIT;
- codel_params_init(&q->params);
+ codel_params_init(&q->params, sch);
codel_vars_init(&q->vars);
codel_stats_init(&q->stats);
q->perturbation = prandom_u32();
INIT_LIST_HEAD(&q->new_flows);
INIT_LIST_HEAD(&q->old_flows);
- codel_params_init(&q->cparams);
+ codel_params_init(&q->cparams, sch);
codel_stats_init(&q->cstats);
q->cparams.ecn = true;
break;
}
- if (q->backlog + qdisc_pkt_len(skb) <= q->limit) {
+ if (gred_backlog(t, q, sch) + qdisc_pkt_len(skb) <= q->limit) {
q->backlog += qdisc_pkt_len(skb);
return qdisc_enqueue_tail(skb, sch);
}
opt.limit = q->limit;
opt.DP = q->DP;
- opt.backlog = q->backlog;
+ opt.backlog = gred_backlog(table, q, sch);
opt.prio = q->prio;
opt.qth_min = q->parms.qth_min >> q->parms.Wlog;
opt.qth_max = q->parms.qth_max >> q->parms.Wlog;
{
u32 value_follows;
int err;
+ struct page *scratch;
+
+ scratch = alloc_page(GFP_KERNEL);
+ if (!scratch)
+ return -ENOMEM;
+ xdr_set_scratch_buffer(xdr, page_address(scratch), PAGE_SIZE);
/* res->status */
err = gssx_dec_status(xdr, &res->status);
if (err)
- return err;
+ goto out_free;
/* res->context_handle */
err = gssx_dec_bool(xdr, &value_follows);
if (err)
- return err;
+ goto out_free;
if (value_follows) {
err = gssx_dec_ctx(xdr, res->context_handle);
if (err)
- return err;
+ goto out_free;
} else {
res->context_handle = NULL;
}
/* res->output_token */
err = gssx_dec_bool(xdr, &value_follows);
if (err)
- return err;
+ goto out_free;
if (value_follows) {
err = gssx_dec_buffer(xdr, res->output_token);
if (err)
- return err;
+ goto out_free;
} else {
res->output_token = NULL;
}
/* res->delegated_cred_handle */
err = gssx_dec_bool(xdr, &value_follows);
if (err)
- return err;
+ goto out_free;
if (value_follows) {
/* we do not support upcall servers sending this data. */
- return -EINVAL;
+ err = -EINVAL;
+ goto out_free;
}
/* res->options */
err = gssx_dec_option_array(xdr, &res->options);
+out_free:
+ __free_page(scratch);
return err;
}
fi, tos, type, nlflags,
tb_id);
if (!err)
- fi->fib_flags |= RTNH_F_EXTERNAL;
+ fi->fib_flags |= RTNH_F_OFFLOAD;
}
return err;
const struct swdev_ops *ops;
int err = 0;
- if (!(fi->fib_flags & RTNH_F_EXTERNAL))
+ if (!(fi->fib_flags & RTNH_F_OFFLOAD))
return 0;
dev = netdev_switch_get_dev_by_nhs(fi);
err = ops->swdev_fib_ipv4_del(dev, htonl(dst), dst_len,
fi, tos, type, tb_id);
if (!err)
- fi->fib_flags &= ~RTNH_F_EXTERNAL;
+ fi->fib_flags &= ~RTNH_F_OFFLOAD;
}
return err;
unix_state_unlock(sk);
timeo = freezable_schedule_timeout(timeo);
unix_state_lock(sk);
+
+ if (sock_flag(sk, SOCK_DEAD))
+ break;
+
clear_bit(SOCK_ASYNC_WAITDATA, &sk->sk_socket->flags);
}
struct sk_buff *skb, *last;
unix_state_lock(sk);
+ if (sock_flag(sk, SOCK_DEAD)) {
+ err = -ECONNRESET;
+ goto unlock;
+ }
last = skb = skb_peek(&sk->sk_receive_queue);
again:
if (skb == NULL) {
$(eval $(1) = $(2)))
endef
-# Allow setting CC and AR, or setting CROSS_COMPILE as a prefix.
+# Allow setting CC and AR and LD, or setting CROSS_COMPILE as a prefix.
$(call allow-override,CC,$(CROSS_COMPILE)gcc)
$(call allow-override,AR,$(CROSS_COMPILE)ar)
+$(call allow-override,LD,$(CROSS_COMPILE)ld)
INSTALL = install
#define __init
#define noinline
#define list_add_tail_rcu list_add_tail
+#define list_for_each_entry_rcu list_for_each_entry
+#define barrier()
+#define synchronize_sched()
#ifndef CALLER_ADDR0
#define CALLER_ADDR0 ((unsigned long)__builtin_return_address(0))
assert(ret == 0);
ptr = haystack;
+ memset(pmatch, 0, sizeof(pmatch));
+
while (1) {
ret = regexec(®ex, ptr, 1, pmatch, 0);
if (ret == 0) {
# (To override it, run 'make JOBS=1' and similar.)
#
ifeq ($(JOBS),)
- JOBS := $(shell egrep -c '^processor|^CPU' /proc/cpuinfo 2>/dev/null)
+ JOBS := $(shell (getconf _NPROCESSORS_ONLN || egrep -c '^processor|^CPU[0-9]' /proc/cpuinfo) 2>/dev/null)
ifeq ($(JOBS),0)
JOBS := 1
endif
-.PHONY: all all_32 all_64 check_build32 clean run_tests
+all:
+
+include ../lib.mk
+
+.PHONY: all all_32 all_64 warn_32bit_failure clean
TARGETS_C_BOTHBITS := sigreturn single_step_syscall
CFLAGS := -O2 -g -std=gnu99 -pthread -Wall
-UNAME_P := $(shell uname -p)
+UNAME_M := $(shell uname -m)
+CAN_BUILD_I386 := $(shell ./check_cc.sh $(CC) trivial_32bit_program.c -m32)
+CAN_BUILD_X86_64 := $(shell ./check_cc.sh $(CC) trivial_64bit_program.c)
-# Always build 32-bit tests
+ifeq ($(CAN_BUILD_I386),1)
all: all_32
+TEST_PROGS += $(BINARIES_32)
+endif
-# If we're on a 64-bit host, build 64-bit tests as well
-ifeq ($(shell uname -p),x86_64)
+ifeq ($(CAN_BUILD_X86_64),1)
all: all_64
+TEST_PROGS += $(BINARIES_64)
endif
-all_32: check_build32 $(BINARIES_32)
+all_32: $(BINARIES_32)
all_64: $(BINARIES_64)
clean:
$(RM) $(BINARIES_32) $(BINARIES_64)
-run_tests:
- ./run_x86_tests.sh
-
$(TARGETS_C_BOTHBITS:%=%_32): %_32: %.c
$(CC) -m32 -o $@ $(CFLAGS) $(EXTRA_CFLAGS) $^ -lrt -ldl
$(TARGETS_C_BOTHBITS:%=%_64): %_64: %.c
$(CC) -m64 -o $@ $(CFLAGS) $(EXTRA_CFLAGS) $^ -lrt -ldl
-check_build32:
- @if ! $(CC) -m32 -o /dev/null trivial_32bit_program.c; then \
- echo "Warning: you seem to have a broken 32-bit build" 2>&1; \
- echo "environment. If you are using a Debian-like"; \
- echo " distribution, try:"; \
- echo ""; \
- echo " apt-get install gcc-multilib libc6-i386 libc6-dev-i386"; \
- echo ""; \
- echo "If you are using a Fedora-like distribution, try:"; \
- echo ""; \
- echo " yum install glibc-devel.*i686"; \
- exit 1; \
- fi
+# x86_64 users should be encouraged to install 32-bit libraries
+ifeq ($(CAN_BUILD_I386)$(CAN_BUILD_X86_64),01)
+all: warn_32bit_failure
+
+warn_32bit_failure:
+ @echo "Warning: you seem to have a broken 32-bit build" 2>&1; \
+ echo "environment. This will reduce test coverage of 64-bit" 2>&1; \
+ echo "kernels. If you are using a Debian-like distribution," 2>&1; \
+ echo "try:"; 2>&1; \
+ echo ""; \
+ echo " apt-get install gcc-multilib libc6-i386 libc6-dev-i386"; \
+ echo ""; \
+ echo "If you are using a Fedora-like distribution, try:"; \
+ echo ""; \
+ echo " yum install glibc-devel.*i686"; \
+ exit 0;
+endif
--- /dev/null
+#!/bin/sh
+# check_cc.sh - Helper to test userspace compilation support
+# Copyright (c) 2015 Andrew Lutomirski
+# GPL v2
+
+CC="$1"
+TESTPROG="$2"
+shift 2
+
+if "$CC" -o /dev/null "$TESTPROG" -O0 "$@" 2>/dev/null; then
+ echo 1
+else
+ echo 0
+fi
+
+exit 0
+++ /dev/null
-#!/bin/bash
-
-# This is deliberately minimal. IMO kselftests should provide a standard
-# script here.
-./sigreturn_32 || exit 1
-./single_step_syscall_32 || exit 1
-
-if [[ "$uname -p" -eq "x86_64" ]]; then
- ./sigreturn_64 || exit 1
- ./single_step_syscall_64 || exit 1
-fi
-
-exit 0
* GPL v2
*/
+#ifndef __i386__
+# error wrong architecture
+#endif
+
#include <stdio.h>
int main()
--- /dev/null
+/*
+ * Trivial program to check that we have a valid 32-bit build environment.
+ * Copyright (c) 2015 Andy Lutomirski
+ * GPL v2
+ */
+
+#ifndef __x86_64__
+# error wrong architecture
+#endif
+
+#include <stdio.h>
+
+int main()
+{
+ printf("\n");
+
+ return 0;
+}
INSTALL_PROGRAM=install -m 755 -p
DEL_FILE=rm -f
-INSTALL_CONFIGFILE=install -m 644 -p
-CONFIG_FILE=
-CONFIG_PATH=
-
# Static builds might require -ltinfo, for instance
ifneq ($(findstring -static, $(LDFLAGS)),)
STATIC := --static
install:
- mkdir -p $(INSTALL_ROOT)/$(BINDIR)
- $(INSTALL_PROGRAM) "$(TARGET)" "$(INSTALL_ROOT)/$(BINDIR)/$(TARGET)"
- - mkdir -p $(INSTALL_ROOT)/$(CONFIG_PATH)
- - $(INSTALL_CONFIGFILE) "$(CONFIG_FILE)" "$(INSTALL_ROOT)/$(CONFIG_PATH)"
uninstall:
$(DEL_FILE) "$(INSTALL_ROOT)/$(BINDIR)/$(TARGET)"
- $(CONFIG_FILE) "$(CONFIG_PATH)"
-
clean:
find . -name "*.o" | xargs $(DEL_FILE)
TARGETS=page-types slabinfo page_owner_sort
LIB_DIR = ../lib/api
-LIBS = $(LIB_DIR)/libapikfs.a
+LIBS = $(LIB_DIR)/libapi.a
CC = $(CROSS_COMPILE)gcc
CFLAGS = -Wall -Wextra -I../lib/
projects / linux.git / commitdiff