# Makefile for the linux kernel, U8500 machine.
#
-obj-y := cpu.o pm.o
-obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
+obj-y := pm.o
obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o
obj-$(CONFIG_MACH_MOP500) += board-mop500-audio.o
obj-$(CONFIG_SMP) += platsmp.o
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#include <asm/outercache.h>
-#include <asm/hardware/cache-l2x0.h>
-
-#include "db8500-regs.h"
-
-static int __init ux500_l2x0_unlock(void)
-{
- int i;
- struct device_node *np;
- void __iomem *l2x0_base;
-
- np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
- l2x0_base = of_iomap(np, 0);
- of_node_put(np);
- if (!l2x0_base)
- return -ENODEV;
-
- /*
- * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
- * apparently locks both caches before jumping to the kernel. The
- * l2x0 core will not touch the unlock registers if the l2x0 is
- * already enabled, so we do it right here instead. The PL310 has
- * 8 sets of registers, one per possible CPU.
- */
- for (i = 0; i < 8; i++) {
- writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
- i * L2X0_LOCKDOWN_STRIDE);
- writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
- i * L2X0_LOCKDOWN_STRIDE);
- }
- iounmap(l2x0_base);
- return 0;
-}
-
-static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
-{
- /*
- * We can't write to secure registers as we are in non-secure
- * mode, until we have some SMI service available.
- */
-}
-
-void __init ux500_l2x0_init(void)
-{
- /* Unlock before init */
- ux500_l2x0_unlock();
- outer_cache.write_sec = ux500_l2c310_write_sec;
-
- return 0;
-}
#include <linux/init.h>
#include <linux/device.h>
#include <linux/amba/bus.h>
+#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/arm-gic.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/arm-ux500-pm.h>
#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/of.h>
+#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/perf/arm_pmu.h>
#include <linux/regulator/machine.h>
+#include <asm/outercache.h>
+#include <asm/hardware/cache-l2x0.h>
#include <asm/mach/map.h>
+#include <asm/mach/arch.h>
#include "setup.h"
#include "board-mop500.h"
#include "db8500-regs.h"
+static int __init ux500_l2x0_unlock(void)
+{
+ int i;
+ struct device_node *np;
+ void __iomem *l2x0_base;
+
+ np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+ l2x0_base = of_iomap(np, 0);
+ of_node_put(np);
+ if (!l2x0_base)
+ return -ENODEV;
+
+ /*
+ * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
+ * apparently locks both caches before jumping to the kernel. The
+ * l2x0 core will not touch the unlock registers if the l2x0 is
+ * already enabled, so we do it right here instead. The PL310 has
+ * 8 sets of registers, one per possible CPU.
+ */
+ for (i = 0; i < 8; i++) {
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+ i * L2X0_LOCKDOWN_STRIDE);
+ }
+ iounmap(l2x0_base);
+ return 0;
+}
+
+static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
+{
+ /*
+ * We can't write to secure registers as we are in non-secure
+ * mode, until we have some SMI service available.
+ */
+}
+
+/*
+ * FIXME: Should we set up the GPIO domain here?
+ *
+ * The problem is that we cannot put the interrupt resources into the platform
+ * device until the irqdomain has been added. Right now, we set the GIC interrupt
+ * domain from init_irq(), then load the gpio driver from
+ * core_initcall(nmk_gpio_init) and add the platform devices from
+ * arch_initcall(customize_machine).
+ *
+ * This feels fragile because it depends on the gpio device getting probed
+ * _before_ any device uses the gpio interrupts.
+*/
+static void __init ux500_init_irq(void)
+{
+ struct device_node *np;
+ struct resource r;
+
+ irqchip_init();
+ np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
+ of_address_to_resource(np, 0, &r);
+ of_node_put(np);
+ if (!r.start) {
+ pr_err("could not find PRCMU base resource\n");
+ return;
+ }
+ prcmu_early_init(r.start, r.end-r.start);
+ ux500_pm_init(r.start, r.end-r.start);
+
+ /* Unlock before init */
+ ux500_l2x0_unlock();
+ outer_cache.write_sec = ux500_l2c310_write_sec;
+}
+
+static void ux500_restart(enum reboot_mode mode, const char *cmd)
+{
+ local_irq_disable();
+ local_fiq_disable();
+
+ prcmu_system_reset(0);
+}
+
/*
* The PMU IRQ lines of two cores are wired together into a single interrupt.
* Bounce the interrupt to the other core if it's not ours.
+++ /dev/null
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * Author: Lee Jones <lee.jones@linaro.org> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/mfd/dbx500-prcmu.h>
-#include <linux/sys_soc.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/stat.h>
-#include <linux/of.h>
-#include <linux/of_irq.h>
-#include <linux/of_address.h>
-#include <linux/irq.h>
-#include <linux/irqchip.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/arm-ux500-pm.h>
-
-#include <asm/mach/map.h>
-
-#include "setup.h"
-
-#include "board-mop500.h"
-#include "db8500-regs.h"
-
-void ux500_restart(enum reboot_mode mode, const char *cmd)
-{
- local_irq_disable();
- local_fiq_disable();
-
- prcmu_system_reset(0);
-}
-
-/*
- * FIXME: Should we set up the GPIO domain here?
- *
- * The problem is that we cannot put the interrupt resources into the platform
- * device until the irqdomain has been added. Right now, we set the GIC interrupt
- * domain from init_irq(), then load the gpio driver from
- * core_initcall(nmk_gpio_init) and add the platform devices from
- * arch_initcall(customize_machine).
- *
- * This feels fragile because it depends on the gpio device getting probed
- * _before_ any device uses the gpio interrupts.
-*/
-void __init ux500_init_irq(void)
-{
- struct device_node *np;
- struct resource r;
-
- irqchip_init();
- np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
- of_address_to_resource(np, 0, &r);
- of_node_put(np);
- if (!r.start) {
- pr_err("could not find PRCMU base resource\n");
- return;
- }
- prcmu_early_init(r.start, r.end-r.start);
- ux500_pm_init(r.start, r.end-r.start);
- ux500_l2x0_init();
-}
#ifndef __ASM_ARCH_SETUP_H
#define __ASM_ARCH_SETUP_H
-#include <asm/mach/arch.h>
-#include <linux/init.h>
-
-
-void ux500_l2x0_init(void);
-
-void ux500_restart(enum reboot_mode mode, const char *cmd);
-
-extern void __init ux500_init_irq(void);
-
extern void ux500_cpu_die(unsigned int cpu);
#endif /* __ASM_ARCH_SETUP_H */
projects / linux.git / commitdiff