From: Fabio Estevam Date: Fri, 8 Nov 2013 01:28:43 +0000 (-0200) Subject: mtd: gpmi-lib: Make checkpatch happy X-Git-Tag: v3.14-rc1~65^2~145 X-Git-Url: https://asedeno.scripts.mit.edu/gitweb/?a=commitdiff_plain;h=76c930be3d4831b52d04aadc2522cfeeb7a6c789;p=linux.git mtd: gpmi-lib: Make checkpatch happy Fix the following checkpatch warnings: WARNING: line over 80 characters #268: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:268: + * consecutive reboots. The latter case has not been seen on the MX23 yet, WARNING: space prohibited before semicolon #356: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:356: + (target.tRHOH_in_ns >= 0) ; WARNING: space prohibited before semicolon #1006: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:1006: + BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ; Signed-off-by: Fabio Estevam Acked-by: Huang Shijie Signed-off-by: Brian Norris --- diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c index aaced29727fb..c7a578c954fb 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -265,8 +265,8 @@ int bch_set_geometry(struct gpmi_nand_data *this) * chip, otherwise it will lock up. So we skip resetting BCH on the MX23. * On the other hand, the MX28 needs the reset, because one case has been * seen where the BCH produced ECC errors constantly after 10000 - * consecutive reboots. The latter case has not been seen on the MX23 yet, - * still we don't know if it could happen there as well. + * consecutive reboots. The latter case has not been seen on the MX23 + * yet, still we don't know if it could happen there as well. */ ret = gpmi_reset_block(r->bch_regs, GPMI_IS_MX23(this)); if (ret) @@ -353,7 +353,7 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, improved_timing_is_available = (target.tREA_in_ns >= 0) && (target.tRLOH_in_ns >= 0) && - (target.tRHOH_in_ns >= 0) ; + (target.tRHOH_in_ns >= 0); /* Inspect the clock. */ nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]); @@ -1003,7 +1003,7 @@ void gpmi_begin(struct gpmi_nand_data *this) /* [1] Set HW_GPMI_TIMING0 */ reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) | BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles) | - BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ; + BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles); writel(reg, gpmi_regs + HW_GPMI_TIMING0);