From: Miquel Raynal Date: Fri, 8 Nov 2019 14:07:40 +0000 (+0100) Subject: spi: zynq-qspi: Keep the bitfields naming consistent X-Git-Tag: v5.5-rc3~39^2~36 X-Git-Url: https://asedeno.scripts.mit.edu/gitweb/?a=commitdiff_plain;h=941be723735113028361c4664cd10134d3d27006;p=linux.git spi: zynq-qspi: Keep the bitfields naming consistent Most of the bits/bitfields #define'd in this driver are composed with: 1/ the driver prefix 2/ the name of the register they apply to Keep the naming consistent by applying this rule to the CONFIG register internals. These definitions will be used in a following change set. Signed-off-by: Miquel Raynal Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com Signed-off-by: Mark Brown --- diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c index 9f53ea08adf7..530533b6c974 100644 --- a/drivers/spi/spi-zynq-qspi.c +++ b/drivers/spi/spi-zynq-qspi.c @@ -60,9 +60,9 @@ * These are the values used in the calculation of baud rate divisor and * setting the slave select. */ -#define ZYNQ_QSPI_BAUD_DIV_MAX GENMASK(2, 0) /* Baud rate maximum */ -#define ZYNQ_QSPI_BAUD_DIV_SHIFT 3 /* Baud rate divisor shift in CR */ -#define ZYNQ_QSPI_SS_SHIFT 10 /* Slave Select field shift in CR */ +#define ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX GENMASK(2, 0) /* Baud rate maximum */ +#define ZYNQ_QSPI_CONFIG_BAUD_DIV_SHIFT 3 /* Baud rate divisor shift */ +#define ZYNQ_QSPI_CONFIG_PCS 10 /* Peripheral Chip Select */ /* * QSPI Interrupt Registers bit Masks @@ -292,7 +292,7 @@ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert) /* Select the slave */ config_reg &= ~ZYNQ_QSPI_CONFIG_SSCTRL_MASK; config_reg |= (((~(BIT(spi->chip_select))) << - ZYNQ_QSPI_SS_SHIFT) & + ZYNQ_QSPI_CONFIG_PCS) & ZYNQ_QSPI_CONFIG_SSCTRL_MASK); } else { config_reg |= ZYNQ_QSPI_CONFIG_SSCTRL_MASK; @@ -331,7 +331,7 @@ static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi) * ---------------- * 111 - divide by 256 */ - while ((baud_rate_val < ZYNQ_QSPI_BAUD_DIV_MAX) && + while ((baud_rate_val < ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX) && (clk_get_rate(xqspi->refclk) / (2 << baud_rate_val)) > spi->max_speed_hz) baud_rate_val++; @@ -347,7 +347,7 @@ static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi) config_reg |= ZYNQ_QSPI_CONFIG_CPOL_MASK; config_reg &= ~ZYNQ_QSPI_CONFIG_BDRATE_MASK; - config_reg |= (baud_rate_val << ZYNQ_QSPI_BAUD_DIV_SHIFT); + config_reg |= (baud_rate_val << ZYNQ_QSPI_CONFIG_BAUD_DIV_SHIFT); zynq_qspi_write(xqspi, ZYNQ_QSPI_CONFIG_OFFSET, config_reg); return 0;