From: Chen-Yu Tsai <wens@csie.org>
Date: Tue, 10 Mar 2015 11:59:24 +0000 (+0800)
Subject: ARM: dts: sun6i: hummingbird: Enable the onboard WiFi module
X-Git-Tag: v4.2-rc1~99^2~48^2~24
X-Git-Url: https://asedeno.scripts.mit.edu/gitweb/?a=commitdiff_plain;h=b5c26d66a4bba25b3a7f1c6ff599975f448e54bd;p=linux.git

ARM: dts: sun6i: hummingbird: Enable the onboard WiFi module

The Hummingbird A31 has an AMPAK AP6210 WiFi+Bluetooth module. The
WiFi part is a BCM43362 IC connected to MMC1 in the A31 SoC via SDIO.
The IC also takes a power enable signal via GPIO. This is supported
with the new power sequencing bindings.

The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not enabled yet.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---

diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts
index d13c88c6509a..25a3ef49bb71 100644
--- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts
+++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts
@@ -61,6 +61,11 @@ / {
 	chosen {
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */
+	};
 };
 
 &ehci0 {
@@ -127,6 +132,16 @@ &mmc0_pins_a {
 	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
 
+&mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_hummingbird>;
+	vmmc-supply = <&vcc_wifi>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
 &ohci0 {
 	status = "okay";
 };
@@ -138,6 +153,13 @@ mmc0_cd_pin_hummingbird: mmc0_cd_pin@0 {
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
+
+	wifi_reset_pin_hummingbird: wifi_reset_pin@0 {
+		allwinner,pins = "PG10";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
 };
 
 &p2wi {