From: Maxime Ripard Date: Thu, 1 Sep 2016 16:27:21 +0000 (+0200) Subject: ARM: gr8: Add CHIP Pro support X-Git-Tag: v4.10-rc1~82^2~14^2~28 X-Git-Url: https://asedeno.scripts.mit.edu/gitweb/?a=commitdiff_plain;h=e63604933ec72b268444a59ca357b4e96449480b;p=linux.git ARM: gr8: Add CHIP Pro support The CHIP Pro is a small embeddable board. It features a GR8, an AXP209 PMIC, a 512MB SLC NAND and a WiFi/BT chip. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai --- diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index c558ba75cbcc..8b4dc8123a66 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -760,6 +760,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a13-olinuxino-micro.dtb \ sun5i-a13-q8-tablet.dtb \ sun5i-a13-utoo-p66.dtb \ + sun5i-gr8-chip-pro.dtb \ sun5i-gr8-evb.dtb \ sun5i-r8-chip.dtb dtb-$(CONFIG_MACH_SUN6I) += \ diff --git a/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts b/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts new file mode 100644 index 000000000000..92a2dc6250a5 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-gr8-chip-pro.dts @@ -0,0 +1,266 @@ +/* + * Copyright 2016 Free Electrons + * Copyright 2016 NextThing Co + * + * Maxime Ripard + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun5i-gr8.dtsi" +#include "sunxi-common-regulators.dtsi" + +#include +#include +#include + +/ { + model = "NextThing C.H.I.P. Pro"; + compatible = "nextthing,chip-pro", "nextthing,gr8"; + + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + leds { + compatible = "gpio-leds"; + + status { + label = "chip-pro:white:status"; + gpios = <&axp_gpio 2 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + mmc0_pwrseq: mmc0_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_reg_on_pin_chip_pro>; + reset-gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */ + }; +}; + +&codec { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + + /* + * The interrupt is routed through the "External Fast + * Interrupt Request" pin (ball G13 of the module) + * directly to the main interrupt controller, without + * any other controller interfering. + */ + interrupts = <0>; + }; +}; + +#include "axp209.dtsi" + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "disabled"; +}; + +&i2s0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_mclk_pins_a>, <&i2s0_data_pins_a>; + status = "disabled"; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>; + vmmc-supply = <®_vcc3v3>; + mmc-pwrseq = <&mmc0_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&nand_pins_a &nand_cs0_pins_a &nand_rb0_pins_a>; + status = "okay"; + + nand@0 { + #address-cells = <2>; + #size-cells = <2>; + reg = <0>; + allwinner,rb = <0>; + nand-ecc-mode = "hw"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&otg_sram { + status = "okay"; +}; + +&pio { + usb0_id_pin_chip_pro: usb0-id-pin@0 { + allwinner,pins = "PG2"; + allwinner,function = "gpio_in"; + allwinner,drive = ; + allwinner,pull = ; + }; + + wifi_reg_on_pin_chip_pro: wifi-reg-on-pin@0 { + allwinner,pins = "PB10"; + allwinner,function = "gpio_out"; + allwinner,drive = ; + allwinner,pull = ; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins_a>, <&pwm1_pins>; + status = "disabled"; +}; + +®_dcdc2 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-cpu"; + regulator-always-on; +}; + +®_dcdc3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-sys"; + regulator-always-on; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; + regulator-always-on; +}; + +/* + * Both LDO3 and LDO4 are used in parallel to power up the + * WiFi/BT chip. + */ +®_ldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-1"; + regulator-always-on; +}; + +®_ldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-2"; + regulator-always-on; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_a>, <&uart1_cts_rts_pins_a>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins_a>, <&uart2_cts_rts_pins_a>; + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins_a>, <&uart3_cts_rts_pins_a>; + status = "okay"; +}; + +&usb_otg { + /* + * The CHIP Pro doesn't have a controllable VBUS, nor does it + * have any 5v rail on the board itself. + * + * If one wants to use it as a true OTG port, it should be + * done in the baseboard, and its DT / overlay will add it. + */ + dr_mode = "otg"; + status = "okay"; +}; + +&usb_power_supply { + status = "okay"; +}; + +&usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_pin_chip_pro>; + usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb1_vbus-supply = <®_vcc5v0>; + status = "okay"; +};