Takashi Iwai [Wed, 10 Jan 2018 09:53:18 +0000 (10:53 +0100)]
ALSA: hda - Apply the existing quirk to iMac 14,1
iMac 14,1 requires the same quirk as iMac 12,2, using GPIO 2 and 3 for
headphone and speaker output amps. Add the codec SSID quirk entry
(106b:0600) accordingly.
Takashi Iwai [Wed, 10 Jan 2018 07:34:28 +0000 (08:34 +0100)]
ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant
There is another Dell XPS 13 variant (SSID 1028:082a) that requires
the existing fixup for reducing the headphone noise.
This patch adds the quirk entry for that.
Takashi Iwai [Mon, 8 Jan 2018 13:03:53 +0000 (14:03 +0100)]
ALSA: pcm: Allow aborting mutex lock at OSS read/write loops
PCM OSS read/write loops keep taking the mutex lock for the whole
read/write, and this might take very long when the exceptionally high
amount of data is given. Also, since it invokes with mutex_lock(),
the concurrent read/write becomes unbreakable.
This patch tries to address these issues by replacing mutex_lock()
with mutex_lock_interruptible(), and also splits / re-takes the lock
at each read/write period chunk, so that it can switch the context
more finely if requested.
Takashi Iwai [Mon, 8 Jan 2018 12:58:31 +0000 (13:58 +0100)]
ALSA: pcm: Abort properly at pending signal in OSS read/write loops
The loops for read and write in PCM OSS emulation have no proper check
of pending signals, and they keep processing even after user tries to
break. This results in a very long delay, often seen as RCU stall
when a huge unprocessed bytes remain queued. The bug could be easily
triggered by syzkaller.
As a simple workaround, this patch adds the proper check of pending
signals and aborts the loop appropriately.
Takashi Iwai [Thu, 4 Jan 2018 16:38:54 +0000 (17:38 +0100)]
ALSA: aloop: Fix racy hw constraints adjustment
The aloop driver tries to update the hw constraints of the connected
target on the cable of the opened PCM substream. This is done by
adding the extra hw constraints rules referring to the substream
runtime->hw fields, while the other substream may update the runtime
hw of another side on the fly.
This is, however, racy and may result in the inconsistent values when
both PCM streams perform the prepare concurrently. One of the reason
is that it overwrites the other's runtime->hw field; which is not only
racy but also broken when it's called before the open of another side
finishes. And, since the reference to runtime->hw isn't protected,
the concurrent write may give the partial value update and become
inconsistent.
This patch is an attempt to fix and clean up:
- The prepare doesn't change the runtime->hw of other side any longer,
but only update the cable->hw that is referred commonly.
- The extra rules refer to the loopback_pcm object instead of the
runtime->hw. The actual hw is deduced from cable->hw.
- The extra rules take the cable_lock to protect against the race.
Takashi Iwai [Fri, 5 Jan 2018 15:15:33 +0000 (16:15 +0100)]
ALSA: aloop: Fix inconsistent format due to incomplete rule
The extra hw constraint rule for the formats the aloop driver
introduced has a slight flaw, where it doesn't return a positive value
when the mask got changed. It came from the fact that it's basically
a copy&paste from snd_hw_constraint_mask64(). The original code is
supposed to be a single-shot and it modifies the mask bits only once
and never after, while what we need for aloop is the dynamic hw rule
that limits the mask bits.
This difference results in the inconsistent state, as the hw_refine
doesn't apply the dependencies fully. The worse and surprisingly
result is that it causes a crash in OSS emulation when multiple
full-duplex reads/writes are performed concurrently (I leave why it
triggers Oops to readers as a homework).
For fixing this, replace a few open-codes with the standard
snd_mask_*() macros.
Takashi Iwai [Fri, 5 Jan 2018 15:09:47 +0000 (16:09 +0100)]
ALSA: aloop: Release cable upon open error path
The aloop runtime object and its assignment in the cable are left even
when opening a substream fails. This doesn't mean any memory leak,
but it still keeps the invalid pointer that may be referred by the
another side of the cable spontaneously, which is a potential Oops
cause.
Clean up the cable assignment and the empty cable upon the error path
properly.
Fixes: 597603d615d2 ("ALSA: introduce the snd-aloop module for the PCM loopback") Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 3 Jan 2018 14:16:30 +0000 (15:16 +0100)]
ALSA: pcm: Workaround for weird PulseAudio behavior on rewind error
The commit 9027c4639ef1 ("ALSA: pcm: Call ack() whenever appl_ptr is
updated") introduced the possible error code returned from the PCM
rewind ioctl. Basically the change was for handling the indirect PCM
more correctly, but ironically, it caused rather a side-effect:
PulseAudio gets pissed off when receiving an error from rewind, throws
everything away and stops processing further, resulting in the
silence.
It's clearly a failure in the application side, so the best would be
to fix that bug in PA. OTOH, PA is mostly the only user of the rewind
feature, so it's not good to slap the sole customer.
This patch tries to mitigate the situation: instead of returning an
error, now the rewind ioctl returns zero when the driver can't rewind.
It indicates that no rewind was performed, so the behavior is
consistent, at least.
In the OSS emulation plugin builder where the frame size is parsed in
the plugin chain, some places miss the possible errors returned from
the plugin src_ or dst_frames callback.
Takashi Iwai [Mon, 1 Jan 2018 08:50:50 +0000 (09:50 +0100)]
ALSA: pcm: Remove incorrect snd_BUG_ON() usages
syzkaller triggered kernel warnings through PCM OSS emulation at
closing a stream:
WARNING: CPU: 0 PID: 3502 at sound/core/pcm_lib.c:1635
snd_pcm_hw_param_first+0x289/0x690 sound/core/pcm_lib.c:1635
Call Trace:
....
snd_pcm_hw_param_near.constprop.27+0x78d/0x9a0 sound/core/oss/pcm_oss.c:457
snd_pcm_oss_change_params+0x17d3/0x3720 sound/core/oss/pcm_oss.c:969
snd_pcm_oss_make_ready+0xaa/0x130 sound/core/oss/pcm_oss.c:1128
snd_pcm_oss_sync+0x257/0x830 sound/core/oss/pcm_oss.c:1638
snd_pcm_oss_release+0x20b/0x280 sound/core/oss/pcm_oss.c:2431
__fput+0x327/0x7e0 fs/file_table.c:210
....
This happens while it tries to open and set up the aloop device
concurrently. The warning above (invoked from snd_BUG_ON() macro) is
to detect the unexpected logical error where snd_pcm_hw_refine() call
shouldn't fail. The theory is true for the case where the hw_params
config rules are static. But for an aloop device, the hw_params rule
condition does vary dynamically depending on the connected target;
when another device is opened and changes the parameters, the device
connected in another side is also affected, and it caused the error
from snd_pcm_hw_refine().
That is, the simplest "solution" for this is to remove the incorrect
assumption of static rules, and treat such an error as a normal error
path. As there are a couple of other places using snd_BUG_ON()
incorrectly, this patch removes these spurious snd_BUG_ON() calls.
Takashi Iwai [Wed, 27 Dec 2017 07:53:59 +0000 (08:53 +0100)]
ALSA: hda - Fix missing COEF init for ALC225/295/299
There was a long-standing problem on HP Spectre X360 with Kabylake
where it lacks of the front speaker output in some situations. Also
there are other products showing the similar behavior. The culprit
seems to be the missing COEF setup on ALC codecs, ALC225/295/299,
which are all compatible.
This patch adds the proper COEF setup (to initialize idx 0x67 / bits
0x3000) for addressing the issue.
Takashi Iwai [Fri, 22 Dec 2017 09:45:07 +0000 (10:45 +0100)]
ALSA: hda: Drop useless WARN_ON()
Since the commit 97cc2ed27e5a ("ALSA: hda - Fix yet another i915
pointer leftover in error path") cleared hdac_acomp pointer, the
WARN_ON() non-NULL check in snd_hdac_i915_register_notifier() may give
a false-positive warning, as the function gets called no matter
whether the component is registered or not. For fixing it, let's get
rid of the spurious WARN_ON().
Hui Wang [Fri, 22 Dec 2017 03:17:46 +0000 (11:17 +0800)]
ALSA: hda - change the location for one mic on a Lenovo machine
There are two front mics on this machine, and current driver assign
the same name Mic to both of them, but pulseaudio can't handle them.
As a workaround, we change the location for one of them, then the
driver will assign "Front Mic" and "Mic" for them.
Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hui Wang [Fri, 22 Dec 2017 03:17:44 +0000 (11:17 +0800)]
ALSA: hda - Add MIC_NO_PRESENCE fixup for 2 HP machines
There is a headset jack on the front panel, when we plug a headset
into it, the headset mic can't trigger unsol events, and
read_pin_sense() can't detect its presence too. So add this fixup
to fix this issue.
Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 20 Dec 2017 16:36:04 +0000 (17:36 +0100)]
Merge tag 'asoc-fix-v4.15-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.15
This is a fairly large set of fixes, they've been delayed partly as more
and more keep coming in. Most of them are very small driver specific
fixes, the biggest individual thing is the revert of the rcar IOMMU
support - it was causing problems and there wasn't the confidence that
it could be resolved sensibly. There's also a relatively large change
in the Freescale SSI controller which resolves some issues with the
AC'97 mode, these aren't that large in the grand scheme of things and
reflect some fairly thorough review and testing.
Brian Norris [Sat, 16 Dec 2017 04:07:23 +0000 (20:07 -0800)]
ASoC: rt5514-spi: only enable wakeup when fully initialized
If an rt5514-spi device is probed but the platform hasn't linked it in,
we might never fully request the SPI IRQ, nor configure the rt5514 DSP,
but we still might try to enable the SPI IRQ (enable_irq_wake()). This
is bad, and among other things, can cause the interrupt to trigger every
time we try to suspend the system (e.g., because the interrupt trigger
setting was never set properly).
Instead of setting our wakeup capabilities in the SPI driver probe
routine, let's wait until we've actually requested the IRQ.
Fixes issues seen on the "kevin" Chromebook (Samsung Chromebook Plus).
Fixes: 58f1c07d23cd ("ASoC: rt5514: Voice wakeup support.") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Abhijeet Kumar [Mon, 11 Dec 2017 19:10:25 +0000 (00:40 +0530)]
ASoC: nau8825: fix issue that pop noise when start capture
In skylake platform, we hear a loud pop noise(0 dB) at start of
audio capture power up sequence. This patch removes the pop noise
from the recording by adding a delay before enabling ADC.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Takashi Iwai [Mon, 18 Dec 2017 22:36:57 +0000 (23:36 +0100)]
ALSA: usb-audio: Fix the missing ctl name suffix at parsing SU
The commit 89b89d121ffc ("ALSA: usb-audio: Add check return value for
usb_string()") added the check of the return value from
snd_usb_copy_string_desc(), which is correct per se, but it introduced
a regression. In the original code, either the "Clock Source",
"Playback Source" or "Capture Source" suffix is added after the
terminal string, while the commit changed it to add the suffix only
when get_term_name() is failing. It ended up with an incorrect ctl
name like "PCM" instead of "PCM Capture Source".
Also, even the original code has a similar bug: when the ctl name is
generated from snd_usb_copy_string_desc() for the given iSelector, it
also doesn't put the suffix.
This patch addresses these issues: the suffix is added always when no
static mapping is found. Also the patch tries to put more comments
and cleans up the if/else block for better readability in order to
avoid the same pitfall again.
Fixes: 89b89d121ffc ("ALSA: usb-audio: Add check return value for usb_string()") Reported-and-tested-by: Mauro Santos <registo.mailling@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kailang Yang [Thu, 14 Dec 2017 07:28:58 +0000 (15:28 +0800)]
ALSA: hda/realtek - Fix Dell AIO LineOut issue
Dell AIO had LineOut jack.
Add LineOut verb into this patch.
[ Additional notes:
the ALC274 codec seems requiring the fixed pin / DAC connections for
HP / line-out pins for enabling EQ for speakers; i.e. the HP / LO
pins expect to be connected with NID 0x03 while keeping the speaker
with NID 0x02. However, by adding a new line-out pin, the
auto-parser assigns the NID 0x02 for HP/LO pins as primary outputs.
As an easy workaround, we provide the preferred_pairs[] to map
forcibly for these pins. -- tiwai ]
Fixes: 75ee94b20b46 ("ALSA: hda - fix headset mic problem for Dell machines with alc274") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
SELinux runs with secureexec for all non-"noatsecure" domain transitions,
which means lots of processes end up hitting the stack hard-limit change
that was introduced in order to fix a race with prlimit(). That race fix
will need to be redesigned.
Reported-by: Laura Abbott <labbott@redhat.com> Reported-by: Tomáš Trnka <trnka@scm.com> Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Dec 2017 21:57:08 +0000 (13:57 -0800)]
Merge branch 'WIP.x86-pti.base-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull Page Table Isolation (PTI) v4.14 backporting base tree from Ingo Molnar:
"This tree contains the v4.14 PTI backport preparatory tree, which
consists of four merges of upstream trees and 7 cherry-picked commits,
which the upcoming PTI work depends on"
NOTE! The resulting tree is exactly the same as the original base tree
(ie the diff between this commit and its immediate first parent is
empty).
The only reason for this merge is literally to have a common point for
the actual PTI changes so that the commits can be shared in both the
4.15 and 4.14 trees.
* 'WIP.x86-pti.base-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
locking/barriers: Convert users of lockless_dereference() to READ_ONCE()
locking/barriers: Add implicit smp_read_barrier_depends() to READ_ONCE()
bpf: fix build issues on um due to mising bpf_perf_event.h
perf/x86: Enable free running PEBS for REGS_USER/INTR
x86: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
x86/cpufeature: Add User-Mode Instruction Prevention definitions
Linus Torvalds [Sun, 17 Dec 2017 21:54:31 +0000 (13:54 -0800)]
Merge branch 'WIP.x86-pti.base.prep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull Page Table Isolation (PTI) preparatory tree from Ingo Molnar:
"This does a rename to free up linux/pti.h to be used by the upcoming
page table isolation feature"
* 'WIP.x86-pti.base.prep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
drivers/misc/intel/pti: Rename the header file to free up the namespace
Arnd Bergmann [Fri, 10 Nov 2017 14:57:21 +0000 (15:57 +0100)]
cramfs: fix MTD dependency
With CONFIG_MTD=m and CONFIG_CRAMFS=y, we now get a link failure:
fs/cramfs/inode.o: In function `cramfs_mount': inode.c:(.text+0x220): undefined reference to `mount_mtd'
fs/cramfs/inode.o: In function `cramfs_mtd_fill_super':
inode.c:(.text+0x6d8): undefined reference to `mtd_point'
inode.c:(.text+0xae4): undefined reference to `mtd_unpoint'
This adds a more specific Kconfig dependency to avoid the broken
configuration.
Alternatively we could make CRAMFS itself depend on "MTD || !MTD" with a
similar result.
Fixes: 99c18ce580c6 ("cramfs: direct memory access support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Dec 2017 20:18:35 +0000 (12:18 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"The alloc_super() one is a regression in this merge window, lazytime
thing is older..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
VFS: Handle lazytime in do_mount()
alloc_super(): do ->s_umount initialization earlier
Linus Torvalds [Sun, 17 Dec 2017 20:14:33 +0000 (12:14 -0800)]
Merge tag 'ext4_for_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix a regression which caused us to fail to interpret symlinks in very
ancient ext3 file system images.
Also fix two xfstests failures, one of which could cause an OOPS, plus
an additional bug fix caught by fuzz testing"
* tag 'ext4_for_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix crash when a directory's i_size is too small
ext4: add missing error check in __ext4_new_inode()
ext4: fix fdatasync(2) after fallocate(2) operation
ext4: support fast symlinks from ext3 file systems
Andrey Ryabinin [Thu, 16 Nov 2017 01:36:35 +0000 (17:36 -0800)]
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
[ Note, this is a Git cherry-pick of the following commit:
d17a1d97dc20: ("x86/mm/kasan: don't use vmemmap_populate() to initialize shadow")
... for easier x86 PTI code testing and back-porting. ]
The KASAN shadow is currently mapped using vmemmap_populate() since that
provides a semi-convenient way to map pages into init_top_pgt. However,
since that no longer zeroes the mapped pages, it is not suitable for
KASAN, which requires zeroed shadow memory.
Add kasan_populate_shadow() interface and use it instead of
vmemmap_populate(). Besides, this allows us to take advantage of
gigantic pages and use them to populate the shadow, which should save us
some memory wasted on page tables and reduce TLB pressure.
Link: http://lkml.kernel.org/r/20171103185147.2688-2-pasha.tatashin@oracle.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Steven Sistare <steven.sistare@oracle.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Bob Picco <bob.picco@oracle.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Alexander Potapenko <glider@google.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: David S. Miller <davem@davemloft.net> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michal Hocko <mhocko@kernel.org> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Will Deacon [Tue, 24 Oct 2017 10:22:47 +0000 (11:22 +0100)]
locking/barriers: Add implicit smp_read_barrier_depends() to READ_ONCE()
[ Note, this is a Git cherry-pick of the following commit:
76ebbe78f739 ("locking/barriers: Add implicit smp_read_barrier_depends() to READ_ONCE()")
... for easier x86 PTI code testing and back-porting. ]
In preparation for the removal of lockless_dereference(), which is the
same as READ_ONCE() on all architectures other than Alpha, add an
implicit smp_read_barrier_depends() to READ_ONCE() so that it can be
used to head dependency chains on all architectures.
Signed-off-by: Will Deacon <will.deacon@arm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1508840570-22169-3-git-send-email-will.deacon@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Daniel Borkmann [Tue, 12 Dec 2017 01:25:31 +0000 (02:25 +0100)]
bpf: fix build issues on um due to mising bpf_perf_event.h
[ Note, this is a Git cherry-pick of the following commit:
a23f06f06dbe ("bpf: fix build issues on um due to mising bpf_perf_event.h")
... for easier x86 PTI code testing and back-porting. ]
Since c895f6f703ad ("bpf: correct broken uapi for
BPF_PROG_TYPE_PERF_EVENT program type") um (uml) won't build
on i386 or x86_64:
[...]
CC init/main.o
In file included from ../include/linux/perf_event.h:18:0,
from ../include/linux/trace_events.h:10,
from ../include/trace/syscall.h:7,
from ../include/linux/syscalls.h:82,
from ../init/main.c:20:
../include/uapi/linux/bpf_perf_event.h:11:32: fatal error:
asm/bpf_perf_event.h: No such file or directory #include
<asm/bpf_perf_event.h>
[...]
Lets add missing bpf_perf_event.h also to um arch. This seems
to be the only one still missing.
Fixes: c895f6f703ad ("bpf: correct broken uapi for BPF_PROG_TYPE_PERF_EVENT program type") Reported-by: Randy Dunlap <rdunlap@infradead.org> Suggested-by: Richard Weinberger <richard@sigma-star.at> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Randy Dunlap <rdunlap@infradead.org> Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com> Cc: Richard Weinberger <richard@sigma-star.at> Acked-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andi Kleen [Thu, 31 Aug 2017 21:46:30 +0000 (14:46 -0700)]
perf/x86: Enable free running PEBS for REGS_USER/INTR
[ Note, this is a Git cherry-pick of the following commit:
a47ba4d77e12 ("perf/x86: Enable free running PEBS for REGS_USER/INTR")
... for easier x86 PTI code testing and back-porting. ]
Currently free running PEBS is disabled when user or interrupt
registers are requested. Most of the registers are actually
available in the PEBS record and can be supported.
So we just need to check for the supported registers and then
allow it: it is all except for the segment register.
For user registers this only works when the counter is limited
to ring 3 only, so this also needs to be checked.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170831214630.21892-1-andi@firstfloor.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rudolf Marek [Tue, 28 Nov 2017 21:01:06 +0000 (22:01 +0100)]
x86: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD
[ Note, this is a Git cherry-pick of the following commit:
2b67799bdf25 ("x86: Make X86_BUG_FXSAVE_LEAK detectable in CPUID on AMD")
... for easier x86 PTI code testing and back-porting. ]
The latest AMD AMD64 Architecture Programmer's Manual
adds a CPUID feature XSaveErPtr (CPUID_Fn80000008_EBX[2]).
If this feature is set, the FXSAVE, XSAVE, FXSAVEOPT, XSAVEC, XSAVES
/ FXRSTOR, XRSTOR, XRSTORS always save/restore error pointers,
thus making the X86_BUG_FXSAVE_LEAK workaround obsolete on such CPUs.
Signed-Off-By: Rudolf Marek <r.marek@assembler.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Borislav Petkov <bp@suse.de> Tested-by: Borislav Petkov <bp@suse.de> Cc: Andy Lutomirski <luto@amacapital.net> Link: https://lkml.kernel.org/r/bdcebe90-62c5-1f05-083c-eba7f08b2540@assembler.cz Signed-off-by: Ingo Molnar <mingo@kernel.org>
... for easier x86 PTI code testing and back-porting. ]
User-Mode Instruction Prevention is a security feature present in new
Intel processors that, when set, prevents the execution of a subset of
instructions if such instructions are executed in user mode (CPL > 0).
Attempting to execute such instructions causes a general protection
exception.
The subset of instructions comprises:
* SGDT - Store Global Descriptor Table
* SIDT - Store Interrupt Descriptor Table
* SLDT - Store Local Descriptor Table
* SMSW - Store Machine Status Word
* STR - Store Task Register
This feature is also added to the list of disabled-features to allow
a cleaner handling of build-time configuration.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Chen Yucong <slaoub@gmail.com> Cc: Chris Metcalf <cmetcalf@mellanox.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Huang Rui <ray.huang@amd.com> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi V. Shankar <ravi.v.shankar@intel.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Tony Luck <tony.luck@intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: ricardo.neri@intel.com Link: http://lkml.kernel.org/r/1509935277-22138-7-git-send-email-ricardo.neri-calderon@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ingo Molnar [Tue, 5 Dec 2017 13:14:47 +0000 (14:14 +0100)]
drivers/misc/intel/pti: Rename the header file to free up the namespace
We'd like to use the 'PTI' acronym for 'Page Table Isolation' - free up the
namespace by renaming the <linux/pti.h> driver header to <linux/intel-pti.h>.
(Also standardize the header guard name while at it.)
Linus Torvalds [Sat, 16 Dec 2017 21:43:08 +0000 (13:43 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"More fixes from testing done on the rc kernel, including more SELinux
testing. Looking forward, lockdep found regression today in ipoib
which is still being fixed.
Summary:
- Fix for SELinux on the umad SMI path. Some old hardware does not
fill the PKey properly exposing another bug in the newer SELinux
code.
- Check the input port as we can exceed array bounds from this user
supplied value
- Users are unable to use the hash field support as they want due to
incorrect checks on the field restrictions, correct that so the
feature works as intended
- User triggerable oops in the NETLINK_RDMA handler
- cxgb4 driver fix for a bad interaction with CQ flushing in iser
caused by patches in this merge window, and bad CQ flushing during
normal close.
- Unbalanced memalloc_noio in ipoib in an error path"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/ipoib: Restore MM behavior in case of tx_ring allocation failure
iw_cxgb4: only insert drain cqes if wq is flushed
iw_cxgb4: only clear the ARMED bit if a notification is needed
RDMA/netlink: Fix general protection fault
IB/mlx4: Fix RSS hash fields restrictions
IB/core: Don't enforce PKey security on SMI MADs
IB/core: Bound check alternate path port number
Linus Torvalds [Sat, 16 Dec 2017 21:12:53 +0000 (13:12 -0800)]
Merge tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs
Pull NFS client fixes from Anna Schumaker:
"This has two stable bugfixes, one to fix a BUG_ON() when
nfs_commit_inode() is called with no outstanding commit requests and
another to fix a race in the SUNRPC receive codepath.
Additionally, there are also fixes for an NFS client deadlock and an
xprtrdma performance regression.
Summary:
Stable bugfixes:
- NFS: Avoid a BUG_ON() in nfs_commit_inode() by not waiting for a
commit in the case that there were no commit requests.
- SUNRPC: Fix a race in the receive code path
Other fixes:
- NFS: Fix a deadlock in nfs client initialization
- xprtrdma: Fix a performance regression for small IOs"
* tag 'nfs-for-4.15-3' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Fix a race in the receive code path
nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
xprtrdma: Spread reply processing over more CPUs
nfs: fix a deadlock in nfs client initialization
We'll probably need to revisit this, but basically we should not
complicate the get_user_pages_fast() case, and checking the actual page
table protection key bits will require more care anyway, since the
protection keys depend on the exact state of the VM in question.
Particularly when doing a "remote" page lookup (ie in somebody elses VM,
not your own), you need to be much more careful than this was. Dave
Hansen says:
"So, the underlying bug here is that we now a get_user_pages_remote()
and then go ahead and do the p*_access_permitted() checks against the
current PKRU. This was introduced recently with the addition of the
new p??_access_permitted() calls.
We have checks in the VMA path for the "remote" gups and we avoid
consulting PKRU for them. This got missed in the pkeys selftests
because I did a ptrace read, but not a *write*. I also didn't
explicitly test it against something where a COW needed to be done"
It's also not entirely clear that it makes sense to check the protection
key bits at this level at all. But one possible eventual solution is to
make the get_user_pages_fast() case just abort if it sees protection key
bits set, which makes us fall back to the regular get_user_pages() case,
which then has a vma and can do the check there if we want to.
We'll see.
Somewhat related to this all: what we _do_ want to do some day is to
check the PAGE_USER bit - it should obviously always be set for user
pages, but it would be a good check to have back. Because we have no
generic way to test for it, we lost it as part of moving over from the
architecture-specific x86 GUP implementation to the generic one in
commit e585513b76f7 ("x86/mm/gup: Switch GUP to the generic
get_user_page_fast() implementation").
Cc: Peter Zijlstra <peterz@infradead.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: "Jérôme Glisse" <jglisse@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
Linus Torvalds [Fri, 15 Dec 2017 21:03:25 +0000 (13:03 -0800)]
Merge tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 4.15-rc4.
There is the usual handful gadget/dwc2/dwc3 fixes as always, for
reported issues. But the most important things in here is the core fix
from Alan Stern to resolve a nasty security bug (my first attempt is
reverted, Alan's was much cleaner), as well as a number of usbip fixes
from Shuah Khan to resolve those reported security issues.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: core: prevent malicious bNumInterfaces overflow
Revert "USB: core: only clean up what we allocated"
USB: core: only clean up what we allocated
Revert "usb: gadget: allow to enable legacy drivers without USB_ETH"
usb: gadget: webcam: fix V4L2 Kconfig dependency
usb: dwc2: Fix TxFIFOn sizes and total TxFIFO size issues
usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
usb: dwc3: of-simple: set dev_pm_ops
usb: dwc3: of-simple: fix missing clk_disable_unprepare
usb: dwc3: gadget: Wait longer for controller to end command processing
usb: xhci: fix TDS for MTK xHCI1.1
xhci: Don't add a virt_dev to the devs array before it's fully allocated
usbip: fix stub_send_ret_submit() vulnerability to null transfer_buffer
usbip: prevent vhci_hcd driver from leaking a socket pointer address
usbip: fix stub_rx: harden CMD_SUBMIT path to handle malicious input
usbip: fix stub_rx: get_pipe() to validate endpoint number
tools/usbip: fixes potential (minor) "buffer overflow" (detected on recent gcc with -Werror)
USB: uas and storage: Add US_FL_BROKEN_FUA for another JMicron JMS567 ID
usb: musb: da8xx: fix babble condition handling
Linus Torvalds [Fri, 15 Dec 2017 20:59:48 +0000 (12:59 -0800)]
Merge tag 'staging-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.15-rc4.
One patch for the ccree driver to prevent an unitialized value from
being returned to a caller, and the other fixes a logic error in the
pi433 driver"
* tag 'staging-4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: pi433: Fixes issue with bit shift in rf69_get_modulation
staging: ccree: Uninitialized return in ssi_ahash_import()
Linus Torvalds [Fri, 15 Dec 2017 20:56:23 +0000 (12:56 -0800)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio regression fixes from Michael Tsirkin:
"Fixes two issues in the latest kernel"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_mmio: fix devm cleanup
ptr_ring: fix up after recent ptr_ring changes
Linus Torvalds [Fri, 15 Dec 2017 20:53:37 +0000 (12:53 -0800)]
Merge tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- fix a particularly nasty DM core bug in a 4.15 refcount_t conversion.
- fix various targets to dm_register_target after module __init
resources created; otherwise racing lvm2 commands could result in a
NULL pointer during initialization of associated DM kernel module.
- fix regression in bio-based DM multipath queue_if_no_path handling.
- fix DM bufio's shrinker to reclaim more than one buffer per scan.
* tag 'for-4.15/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm bufio: fix shrinker scans when (nr_to_scan < retain_target)
dm mpath: fix bio-based multipath queue_if_no_path handling
dm: fix various targets to dm_register_target after module __init resources created
dm table: fix regression from improper dm_dev_internal.count refcount_t conversion
Linus Torvalds [Fri, 15 Dec 2017 20:51:42 +0000 (12:51 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"The most important one is the bfa fix because it's easy to oops the
kernel with this driver (this includes the commit that corrects the
compiler warning in the original), a regression in the new timespec
conversion in aacraid and a regression in the Fibre Channel ELS
handling patch.
The other three are a theoretical problem with termination in the
vendor/host matching code and a use after free in lpfc.
The additional patches are a fix for an I/O hang in the mq code under
certain circumstances and a rare oops in some debugging code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Fix a scsi_show_rq() NULL pointer dereference
scsi: MAINTAINERS: change FCoE list to linux-scsi
scsi: libsas: fix length error in sas_smp_handler()
scsi: bfa: fix type conversion warning
scsi: core: run queue if SCSI device queue isn't ready and queue is idle
scsi: scsi_devinfo: cleanly zero-pad devinfo strings
scsi: scsi_devinfo: handle non-terminated strings
scsi: bfa: fix access to bfad_im_port_s
scsi: aacraid: address UBSAN warning regression
scsi: libfc: fix ELS request handling
scsi: lpfc: Use after free in lpfc_rq_buf_free()
Linus Torvalds [Fri, 15 Dec 2017 20:49:54 +0000 (12:49 -0800)]
Merge tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"A couple of MMC fixes:
- fix use of uninitialized drv_typ variable
- apply NO_CMD23 quirk to some specific SD cards to make them work"
* tag 'mmc-v4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: apply NO_CMD23 quirk to some specific cards
mmc: core: properly init drv_type
Linus Torvalds [Fri, 15 Dec 2017 20:46:48 +0000 (12:46 -0800)]
Merge branch 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
- fix incomplete syncing of filesystem
- fix regression in readdir on ovl over 9p
- only follow redirects when needed
- misc fixes and cleanups
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix overlay: warning prefix
ovl: Use PTR_ERR_OR_ZERO()
ovl: Sync upper dirty data when syncing overlayfs
ovl: update ctx->pos on impure dir iteration
ovl: Pass ovl_get_nlink() parameters in right order
ovl: don't follow redirects if redirect_dir=off
Hemanth Puranik [Fri, 15 Dec 2017 14:35:58 +0000 (20:05 +0530)]
net: qcom/emac: Reduce timeout for mdio read/write
Currently mdio read/write takes around ~115us as the timeout
between status check is set to 100us.
By reducing the timeout to 1us mdio read/write takes ~15us to
complete. This improves the link up event response.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org> Acked-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 15 Dec 2017 20:44:49 +0000 (12:44 -0800)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"There are some significant fixes in here for FP state corruption,
hardware access/dirty PTE corruption and an erratum workaround for the
Falkor CPU.
I'm hoping that things finally settle down now, but never say never...
Summary:
- Fix FPSIMD context switch regression introduced in -rc2
- Fix ABI break with SVE CPUID register reporting
- Fix use of uninitialised variable
- Fixes to hardware access/dirty management and sanity checking
- CPU erratum workaround for Falkor CPUs
- Fix reporting of writeable+executable mappings
- Fix signal reporting for RAS errors"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fpsimd: Fix copying of FP state from signal frame into task struct
arm64/sve: Report SVE to userspace via CPUID only if supported
arm64: fix CONFIG_DEBUG_WX address reporting
arm64: fault: avoid send SIGBUS two times
arm64: hw_breakpoint: Use linux/uaccess.h instead of asm/uaccess.h
arm64: Add software workaround for Falkor erratum 1041
arm64: Define cputype macros for Falkor CPU
arm64: mm: Fix false positives in set_pte_at access/dirty race detection
arm64: mm: Fix pte_mkclean, pte_mkdirty semantics
arm64: Initialise high_memory global variable earlier
Jiri Pirko [Fri, 15 Dec 2017 11:40:13 +0000 (12:40 +0100)]
net: sched: fix static key imbalance in case of ingress/clsact_init error
Move static key increments to the beginning of the init function
so they pair 1:1 with decrements in ingress/clsact_destroy,
which is called in case ingress/clsact_init fails.
Fixes: 6529eaba33f0 ("net: sched: introduce tcf block infractructure") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 15 Dec 2017 11:40:12 +0000 (12:40 +0100)]
net: sched: fix clsact init error path
Since in qdisc_create, the destroy op is called when init fails, we
don't do cleanup in init and leave it up to destroy.
This fixes use-after-free when trying to put already freed block.
Fixes: 6e40cf2d4dee ("net: sched: use extended variants of block_get/put in ingress and clsact qdiscs") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 15 Dec 2017 20:14:33 +0000 (12:14 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- fix the s2ram regression related to confusion around segment
register restoration, plus related cleanups that make the code more
robust
- a guess-unwinder Kconfig dependency fix
- an isoimage build target fix for certain tool chain combinations
- instruction decoder opcode map fixes+updates, and the syncing of
the kernel decoder headers to the objtool headers
- a kmmio tracing fix
- two 5-level paging related fixes
- a topology enumeration fix on certain SMP systems"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Resync objtool's instruction decoder source code copy with the kernel's latest version
x86/decoder: Fix and update the opcodes map
x86/power: Make restore_processor_context() sane
x86/power/32: Move SYSENTER MSR restoration to fix_processor_context()
x86/power/64: Use struct desc_ptr for the IDT in struct saved_context
x86/unwinder/guess: Prevent using CONFIG_UNWINDER_GUESS=y with CONFIG_STACKDEPOT=y
x86/build: Don't verify mtools configuration file for isoimage
x86/mm/kmmio: Fix mmiotrace for page unaligned addresses
x86/boot/compressed/64: Print error if 5-level paging is not supported
x86/boot/compressed/64: Detect and handle 5-level paging at boot-time
x86/smpboot: Do not use smp_num_siblings in __max_logical_packages calculation
Linus Torvalds [Fri, 15 Dec 2017 19:44:59 +0000 (11:44 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Misc fixes:
- Fix a S390 boot hang that was caused by the lock-break logic.
Remove lock-break to begin with, as review suggested it was
unreasonably fragile and our confidence in its continued good
health is lower than our confidence in its removal.
- Remove the lockdep cross-release checking code for now, because of
unresolved false positive warnings. This should make lockdep work
well everywhere again.
- Get rid of the final (and single) ACCESS_ONCE() straggler and
remove the API from v4.15.
- Fix a liblockdep build warning"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/lib/lockdep: Add missing declaration of 'pr_cont()'
checkpatch: Remove ACCESS_ONCE() warning
compiler.h: Remove ACCESS_ONCE()
tools/include: Remove ACCESS_ONCE()
tools/perf: Convert ACCESS_ONCE() to READ_ONCE()
locking/lockdep: Remove the cross-release locking checks
locking/core: Remove break_lock field when CONFIG_GENERIC_LOCKBREAK=y
locking/core: Fix deadlock during boot on systems with GENERIC_LOCKBREAK
Linus Torvalds [Fri, 15 Dec 2017 19:40:24 +0000 (11:40 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Two fixes: a crash fix for an ARM SoC platform, and kernel-doc
warnings fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt: Do not pull from current CPU if only one CPU to pull
sched/core: Fix kernel-doc warnings after code movement
Linus Torvalds [Fri, 15 Dec 2017 19:32:09 +0000 (11:32 -0800)]
Merge tag 'for-linus-4.15-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two minor fixes for running as Xen dom0:
- when built as 32 bit kernel on large machines the Xen LAPIC
emulation should report a rather modern LAPIC in order to support
enough APIC-Ids
- The Xen LAPIC emulation is needed for dom0 only, so build it only
for kernels supporting to run as Xen dom0"
* tag 'for-linus-4.15-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: XEN_ACPI_PROCESSOR is Dom0-only
x86/Xen: don't report ancient LAPIC version
Scott Mayhew [Fri, 8 Dec 2017 21:00:12 +0000 (16:00 -0500)]
nfs: don't wait on commit in nfs_commit_inode() if there were no commit requests
If there were no commit requests, then nfs_commit_inode() should not
wait on the commit or mark the inode dirty, otherwise the following
BUG_ON can be triggered:
Chuck Lever [Mon, 4 Dec 2017 19:04:04 +0000 (14:04 -0500)]
xprtrdma: Spread reply processing over more CPUs
Commit d8f532d20ee4 ("xprtrdma: Invoke rpcrdma_reply_handler
directly from RECV completion") introduced a performance regression
for NFS I/O small enough to not need memory registration. In multi-
threaded benchmarks that generate primarily small I/O requests,
IOPS throughput is reduced by nearly a third. This patch restores
the previous level of throughput.
Because workqueues are typically BOUND (in particular ib_comp_wq,
nfsiod_workqueue, and rpciod_workqueue), NFS/RDMA workloads tend
to aggregate on the CPU that is handling Receive completions.
The usual approach to addressing this problem is to create a QP
and CQ for each CPU, and then schedule transactions on the QP
for the CPU where you want the transaction to complete. The
transaction then does not require an extra context switch during
completion to end up on the same CPU where the transaction was
started.
This approach doesn't work for the Linux NFS/RDMA client because
currently the Linux NFS client does not support multiple connections
per client-server pair, and the RDMA core API does not make it
straightforward for ULPs to determine which CPU is responsible for
handling Receive completions for a CQ.
So for the moment, record the CPU number in the rpcrdma_req before
the transport sends each RPC Call. Then during Receive completion,
queue the RPC completion on that same CPU.
Additionally, move all RPC completion processing to the deferred
handler so that even RPCs with simple small replies complete on
the CPU that sent the corresponding RPC Call.
Fixes: d8f532d20ee4 ("xprtrdma: Invoke rpcrdma_reply_handler ...") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Scott Mayhew [Tue, 5 Dec 2017 18:55:44 +0000 (13:55 -0500)]
nfs: fix a deadlock in nfs client initialization
The following deadlock can occur between a process waiting for a client
to initialize in while walking the client list during nfsv4 server trunking
detection and another process waiting for the nfs_clid_init_mutex so it
can initialize that client:
Process 1 Process 2
--------- ---------
spin_lock(&nn->nfs_client_lock);
list_add_tail(&CLIENTA->cl_share_link,
&nn->nfs_client_list);
spin_unlock(&nn->nfs_client_lock);
spin_lock(&nn->nfs_client_lock);
list_add_tail(&CLIENTB->cl_share_link,
&nn->nfs_client_list);
spin_unlock(&nn->nfs_client_lock);
mutex_lock(&nfs_clid_init_mutex);
nfs41_walk_client_list(clp, result, cred);
nfs_wait_client_init_complete(CLIENTA);
(waiting for nfs_clid_init_mutex)
Make sure nfs_match_client() only evaluates clients that have completed
initialization in order to prevent that deadlock.
This patch also fixes v4.0 trunking behavior by not marking the client
NFS_CS_READY until the clientid has been confirmed.
Signed-off-by: Scott Mayhew <smayhew@redhat.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Haishuang Yan [Fri, 15 Dec 2017 02:46:16 +0000 (10:46 +0800)]
ip_gre: fix wrong return value of erspan_rcv
If pskb_may_pull return failed, return PACKET_REJECT instead of -ENOMEM.
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: sched: Make qdisc offload uapi uniform
Several qdiscs can already be offloaded to hardware, but there's an
inconsistecy in regard to the uapi through which they indicate such
an offload is taking place - indication is passed to the user via
TCA_OPTIONS where each qdisc retains private logic for setting it.
The recent addition of offloading to RED in 602f3baf2218 ("net_sch: red: Add offload ability to RED qdisc") caused
the addition of yet another uapi field for this purpose -
TC_RED_OFFLOADED.
For clarity and prevention of bloat in the uapi we want to eliminate
said added uapi, replacing it with a common mechanism that can be used
to reflect offload status of the various qdiscs.
The first patch introduces TCA_HW_OFFLOAD as the generic message meant
for this purpose. The second changes the current RED implementation into
setting the internal bits necessary for passing it, and the third removes
TC_RED_OFFLOADED as its no longer needed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 14 Dec 2017 13:54:31 +0000 (15:54 +0200)]
pkt_sched: Remove TC_RED_OFFLOADED from uapi
Following the previous patch, RED is now using the new uniform uapi
for indicating it's offloaded. As a result, TC_RED_OFFLOADED is no
longer utilized by kernel and can be removed [as it's still not
part of any stable release].
Fixes: 602f3baf2218 ("net_sch: red: Add offload ability to RED qdisc") Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 14 Dec 2017 13:54:30 +0000 (15:54 +0200)]
net: sched: Move to new offload indication in RED
Let RED utilize the new internal flag, TCQ_F_OFFLOADED,
to mark a given qdisc as offloaded instead of using a dedicated
indication.
Also, change internal logic into looking at said flag when possible.
Fixes: 602f3baf2218 ("net_sch: red: Add offload ability to RED qdisc") Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Thu, 14 Dec 2017 13:54:29 +0000 (15:54 +0200)]
net: sched: Add TCA_HW_OFFLOAD
Qdiscs can be offloaded to HW, but current implementation isn't uniform.
Instead, qdiscs either pass information about offload status via their
TCA_OPTIONS or omit it altogether.
Introduce a new attribute - TCA_HW_OFFLOAD that would form a uniform
uAPI for the offloading status of qdiscs.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The patchset contains important hardware fix for machines with large MRRS
and couple of improvement in stats and capabilities reporting
patch v3:
- Fixed patch #7 after Andrew's finding. NIC level stats actually
have to be cleaned only on hw struct creation (and this is done
in kzalloc). On each hwinit we only have to reset link state
to make sure hw stats update will not increment nic stats during init.
patch v2:
- split into more detailed commits
Comment from David on wrong defines case will be submitted separately later
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Thu, 14 Dec 2017 09:34:46 +0000 (12:34 +0300)]
net: aquantia: Update hw counters on hw init
On very first start we should read out current HW counter values
to make diff based calculations later.
This also should be done each time NIC gets down/up or wakes up
after sleep state. We reset link state explicitly to prevent diffs
from being summed this first time.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Thu, 14 Dec 2017 09:34:43 +0000 (12:34 +0300)]
net: aquantia: Fill ndev stat couters from hardware
Originally they were filled from ring sw counters.
These sometimes incorrectly calculate byte and packet amounts
when using LRO/LSO and jumboframes. Filling ndev counters from
hardware makes them precise.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Thu, 14 Dec 2017 09:34:42 +0000 (12:34 +0300)]
net: aquantia: Extend stat counters to 64bit values
Device hardware provides only 32bit counters. Using these directly
causes byte counters to overflow soon. A separate nic level structure
with 64 bit counters is now used to collect incrementally all the stats
and report these counters to ethtool stats and ndev stats.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Thu, 14 Dec 2017 09:34:41 +0000 (12:34 +0300)]
net: aquantia: Fix hardware DMA stream overload on large MRRS
Systems with large MRRS on device (2K, 4K) with high data rates and/or
large MTU, atlantic observes DMA packet buffer overflow. On some systems
that causes PCIe transaction errors, hardware NMIs or datapath freeze.
This patch
1) Limits MRRS from device side to 2K (thats maximum our hardware supports)
2) Limit maximum size of outstanding TX DMA data read requests. This makes
hardware buffers running fine.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Thu, 14 Dec 2017 09:34:40 +0000 (12:34 +0300)]
net: aquantia: Fix actual speed capabilities reporting
Different hardware device Ids correspond to different maximum speed
available. Extra checks were added for devices D108 and D109 to
remove unsupported speeds from these device capabilities list.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Wed, 13 Dec 2017 19:41:06 +0000 (14:41 -0500)]
sock: free skb in skb_complete_tx_timestamp on error
skb_complete_tx_timestamp must ingest the skb it is passed. Call
kfree_skb if the skb cannot be enqueued.
Fixes: b245be1f4db1 ("net-timestamp: no-payload only sysctl") Fixes: 9ac25fc06375 ("net: fix socket refcounting in skb_complete_tx_timestamp()") Reported-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Dec 2017 16:29:44 +0000 (11:29 -0500)]
Merge branch 's390-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2017-12-13
some more patches for 4.15, that fix multiple issues with IP Takeover
configuration in qeth.
Please queue them up for stable kernels as well (4.9 and newer).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 13 Dec 2017 17:56:32 +0000 (18:56 +0100)]
s390/qeth: update takeover IPs after configuration change
Any modification to the takeover IP-ranges requires that we re-evaluate
which IP addresses are takeover-eligible. Otherwise we might do takeover
for some addresses when we no longer should, or vice-versa.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 13 Dec 2017 17:56:31 +0000 (18:56 +0100)]
s390/qeth: lock IP table while applying takeover changes
Modifying the flags of an IP addr object needs to be protected against
eg. concurrent removal of the same object from the IP table.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback") Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 13 Dec 2017 17:56:30 +0000 (18:56 +0100)]
s390/qeth: don't apply takeover changes to RXIP
When takeover is switched off, current code clears the 'TAKEOVER' flag on
all IPs. But the flag is also used for RXIP addresses, and those should
not be affected by the takeover mode.
Fix the behaviour by consistenly applying takover logic to NORMAL
addresses only.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 13 Dec 2017 17:56:29 +0000 (18:56 +0100)]
s390/qeth: apply takeover changes when mode is toggled
Just as for an explicit enable/disable, toggling the takeover mode also
requires that the IP addresses get updated. Otherwise all IPs that were
added to the table before the mode-toggle, get registered with the old
settings.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Will Deacon [Fri, 15 Dec 2017 16:07:22 +0000 (16:07 +0000)]
arm64: fpsimd: Fix copying of FP state from signal frame into task struct
Commit 9de52a755cfb6da5 ("arm64: fpsimd: Fix failure to restore FPSIMD
state after signals") fixed an issue reported in our FPSIMD signal
restore code but inadvertently introduced another issue which tends to
manifest as random SEGVs in userspace.
The problem is that when we copy the struct fpsimd_state from the kernel
stack (populated from the signal frame) into the struct held in the
current thread_struct, we blindly copy uninitialised stack into the
"cpu" field, which means that context-switching of the FP registers is
no longer reliable.
This patch fixes the problem by copying only the user_fpsimd member of
struct fpsimd_state. We should really rework the function prototypes
to take struct user_fpsimd_state * instead, but let's just get this
fixed for now.
Cc: Dave Martin <Dave.Martin@arm.com> Fixes: 9de52a755cfb6da5 ("arm64: fpsimd: Fix failure to restore FPSIMD state after signals") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Will Deacon <will.deacon@arm.com>
Yuval Mintz [Fri, 15 Dec 2017 07:44:21 +0000 (08:44 +0100)]
mlxsw: spectrum: Disable MAC learning for ovs port
Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.
Fixes: 2b94e58df58c ("mlxsw: spectrum: Allow ports to work under OVS master") Signed-off-by: Yuval Mintz <yuvalm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>