Lucas Stach [Mon, 11 Dec 2017 16:58:34 +0000 (16:58 +0000)]
ARM: dts: imx6*-hummingboard2: rework regulators
Name the regulators according to the voltage rails they are feeding in
the schematic. The USB 2-4 regulators are fixed regulators and are always
on, as they are not a VBUS supply for a single USB host port on the i.MX6,
but supply VBUS to ports behind a USB hub and there is currently no way
to model this in mainline.
Signed-off-by: Lucas Stach <dev@lynxeye.de> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Stefan Agner [Tue, 19 Dec 2017 18:10:38 +0000 (19:10 +0100)]
ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support
Add support for the Computer on Module Colibri iMX7D 1GB along
with the Colibri Evaluation Board device trees. Follow the usual
hierarchic include model, maintaining shared configuration in
imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Stefan Agner [Tue, 19 Dec 2017 18:10:37 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: add MCP2515 CAN controller
The Colibri Evaluation Carrier Board provides a MCP2515 CAN
controller connected via SPI. Note that the i.MX 7 provides
an internal CAN controller which is much better suited for CAN
operations. Using the MCP2515 with a Colibri iMX7 module is
mainly useful to test the SPI interface.
Stefan Agner [Tue, 19 Dec 2017 18:10:35 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: specify usdhc1 supplies
The usdhc1 controller instance is used to provide the default
SD/MMC capabilities of the Colibri standard. The IO pins are
supplied to the SoC on the module whereas the SD-card is powered
by the Carrier Board supply.
Stefan Agner [Tue, 19 Dec 2017 18:10:30 +0000 (19:10 +0100)]
ARM: dts: imx7-colibri: move and rename USB Host power regulator
The Colibri default which enables USB Host power is not necessarily
tied to the OTG2 controller, some carrier board use the pin to
control USB power for both controllers. Hence name the pinctrl
group more generic.
Also move the regulator to the generic eval-v3 device tree since
the regulator is always on the carrier board. In the Colibri iMX7S
case the regulator is just not used. This allows to reuse the
regulator in a upcoming SKU Colibri iMX7D 1GB with eMMC.
Stefan Agner [Wed, 6 Dec 2017 10:29:29 +0000 (11:29 +0100)]
ARM: dts: colibri/apalis: use correct compatible for RTC
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared
to a st,m41t00 this RTC has also an oscillator fail bit which allows
to detect when the RTC lost track of time.
Fabio Estevam [Mon, 4 Dec 2017 12:20:15 +0000 (10:20 -0200)]
ARM: dts: imx6qdl-nitrogen6_max: Remove unneeded unit address
Remove the unneeded unit address for the i2cmux nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-nitrogen6_max.dtb: Warning (unit_address_vs_reg): Node /i2cmux@3 has a unit name, but no reg property
While at it, rename the i2cmux nodes and subnodes to make it clearer to which
i2c controller the mux belongs to.
Fabio Estevam [Mon, 4 Dec 2017 12:20:14 +0000 (10:20 -0200)]
ARM: dts: imx6q-h100: Remove unneeded unit address
Remove the unneeded unit address for the port nodes in order to fix
the following build warnings with W=1:
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a0000/tc358743@f/port@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6q-h100.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@0 has a unit name, but no reg property
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx6q-apalis-eval.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/i2c@21a4000/stmpe811@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:10 +0000 (10:20 -0200)]
ARM: dts: imx6qdl-aristainetos: Move regulators out of simple-bus
It is not recommended to place regulator nodes inside simple-bus, so
move them out in order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-aristainetos_4.dtb: Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit name, but no reg property
Fabio Estevam [Mon, 4 Dec 2017 12:20:07 +0000 (10:20 -0200)]
ARM: dts: imx53-m53: Remove unneeded reg property
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt
there is no 'reg' property under stmpe_touchscreen, so remove it
to fix the following build warning with W=1:
arch/arm/boot/dts/imx53-m53evk.dtb: Warning (unit_address_vs_reg): Node /soc/aips@60000000/i2c@63fc4000/stmpe610@41/stmpe_touchscreen has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:06 +0000 (10:20 -0200)]
ARM: dts: imx51-zii-rdu1: Add the unit addresses in sysled
As described at Documentation/devicetree/bindings/mfd/mc13xxx.txt the
reg property is mandatory, so add the corresponding unit address in
order to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled0 has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled1 has a reg or ranges property, but no unit name
Fabio Estevam [Mon, 4 Dec 2017 12:20:05 +0000 (10:20 -0200)]
ARM: dts: imx51-ts4800: Fix syscon and touschscreen nodes
The syscon node has an incorrect notation for its unit address and the
wdt node has an unneeded unit address.
Fix them so that the following build warnings with W=1 are gone:
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000/wdt@e has a unit name, but no reg property
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (unit_address_vs_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/syscon@b0010000 simple-bus unit address format error, expected "10000"
arch/arm/boot/dts/imx51-ts4800.dtb: Warning (simple_bus_reg): Node /soc/aips@80000000/weim@83fda000/fpga@0/touchscreen simple-bus unit address format error, expected "12000"
Neil Armstrong [Mon, 4 Dec 2017 09:21:09 +0000 (10:21 +0100)]
ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6
SoM Carrier-Board.
This Carrier-Board has the following :
- LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display
- HDMI Connector
- USB Host + USB OTG Connector
- 10/100/1000 Mbps Ethernet
- miniPCI-Express slot
- SD Card connector
- Audio Headphone/Line In jack connectors
- On-board DMIC
- CAN bus header
- SPI header
- Camera Interfaces header
- 4xButtons, 2xLeds
- OnBoard RTC with Coin Backup battery socket
- RS232 Header + USB-Serial debug port
The board support is done with all on-board and header interfaces enabled.
7" LVDS Touchscreen is enabled by default along HDMI output.
Audio interface is supported with the "simple-card" bindings.
PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet.
Vanessa Maegima [Thu, 30 Nov 2017 17:55:17 +0000 (15:55 -0200)]
ARM: dts: imx7d-pico-pi: Separate into cpu and baseboard dts
Separate the old imx7d-pico into cpu (imx7d-pico.dtsi) and baseboard
(imx7d-pico-pi.dts) dts so the same cpu dtsi can be used in different
baseboards variants.
Fabio Estevam [Wed, 29 Nov 2017 18:54:38 +0000 (16:54 -0200)]
ARM: dts: imx6dl: Remove unneeded label and unit address
Remove unneeded label and unit address in order to fix the following
build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi0_mux@34 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2000000/iomuxc-gpr@20e0000/ipu1_csi1_mux@34 has a unit name, but no
Fabio Estevam [Wed, 29 Nov 2017 18:54:37 +0000 (16:54 -0200)]
ARM: dts: imx6dl: Pass the reg properties for mipi nodes
Pass the reg properties for mipi nodes in order to fix the
following build warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@1/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@2/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@3/endpoint@1 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@0 has a unit name, but no reg property
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unit_address_vs_reg): Node /soc/aips-bus@2100000/mipi@21dc000/port@4/endpoint@1 has a unit name, but no reg property
Fabio Estevam [Wed, 29 Nov 2017 18:54:34 +0000 (16:54 -0200)]
ARM: dts: imx53: Move nodes which have no reg property out of bus
Move pmu, usbphy0 and usbphy1 nodes from soc node to root node.
The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.
This fixes the following build warnings with W=1:
arch/arm/boot/dts/imx53-ard.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-0 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-1 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property
Based on a patch from Simon Horman for r8a7795.dtsi.
Yangbo Lu [Wed, 29 Nov 2017 06:54:58 +0000 (14:54 +0800)]
ARM: dts: ls1021a: fix the value of TMR_FIPER1
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Tue, 28 Nov 2017 15:02:25 +0000 (15:02 +0000)]
ARM: dts: imx6qdl-sr-som: split out Broadcom Wi-Fi support
There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi. The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Tue, 28 Nov 2017 15:02:10 +0000 (15:02 +0000)]
ARM: dts: imx6qdl-microsom: rename to imx6qdl-sr-som
Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom. Change the name to the shorter "imx6qdl-sr-som".
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Tue, 28 Nov 2017 15:02:05 +0000 (15:02 +0000)]
ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom
As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file. Move the
AR8035 support into the main imx6qdl-microsom file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM: dts: imx6qdl-udoo: add support for powering off
UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.
This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).
Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).
To power the SoC up again press the power button (SW2, the one with a long
shaft).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 21 Nov 2017 22:49:59 +0000 (20:49 -0200)]
ARM: dts: imx6sx-sdb: Rearrange the regulators node
It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.
ARM: dts: imx6qdl-udoo: disable AC'97 input pins pad drivers
AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.
This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rasmus Villemoes [Thu, 16 Nov 2017 12:15:26 +0000 (13:15 +0100)]
ARM: dts: ls1021a: add "fsl,ls1021a-esdhc" compatible string to esdhc node
Commit a22950c888e3 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Rob Herring [Thu, 9 Nov 2017 22:26:10 +0000 (16:26 -0600)]
ARM: dts: imx: Add missing #phy-cells to usb-nop-xceiv
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in i.MX dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...