Rafał Miłecki [Thu, 11 Oct 2018 07:40:22 +0000 (09:40 +0200)]
spi: bcm-qspi: fix calculation of address length
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
Boris Brezillon [Thu, 20 Sep 2018 07:31:10 +0000 (09:31 +0200)]
spi: spi-mem: Add missing description for data.nbytes field
Add a description for spi_mem_op.data.nbytes to the kerneldoc header.
Fixes: c36ff266dc82 ("spi: Extend the core to ease integration of SPI memory controllers") Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
spi: rspi: Fix invalid SPI use during system suspend
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
spi: sh-msiof: Fix invalid SPI use during system suspend
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b901ff672 ("spi: spi-gpio: Rewrite to use GPIO descriptors") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:
WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
couldn't get idr
Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.
Fixes: 1a4327fbf4554d5b ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Kirill Kapranov [Mon, 13 Aug 2018 16:48:10 +0000 (19:48 +0300)]
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
On systems where some controllers get a dynamic ID assigned and some have
a fixed number (e.g. from ACPI tables), the current implementation might
run into an IDR collision: in case of a fixed bus number is gotten by a
driver (but not marked busy in IDR tree) and a driver with dynamic bus
number gets the same ID and predictably fails.
Fix this by means of checking-in fixed IDsin IDR as far as dynamic ones
at the moment of the controller registration.
Fixes: 9b61e302210e (spi: Pick spi bus number from Linux idr or spi alias) Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
Boris Brezillon [Fri, 3 Aug 2018 09:50:39 +0000 (11:50 +0200)]
spi: spi-mem: Constify spi_mem->name
There is no reason to make spi_mem->name modifiable. Moreover,
spi_mem_ops->get_name() returns a const char *, which generates a gcc
warning when assigning the value returned by spi_mem_ops->get_name()
to spi_mem->name.
Fixes: 5d27a9c8ea9e ("spi: spi-mem: Extend the SPI mem interface to set a custom memory name") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
mtd: m25p80: Call spi_mem_get_name() to let controller set a custom name
By calling spi_mem_get_name(), the driver of the (Q)SPI controller can
set a custom name for the memory device if necessary.
This is useful to keep mtdparts compatible when controller drivers are
ported from the MTD to the SPI layer.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-mem: Extend the SPI mem interface to set a custom memory name
When porting (Q)SPI controller drivers from the MTD layer to the SPI
layer, the naming scheme for the memory devices changes. To be able
to keep compatibility with the old drivers naming scheme, a name
field is added to struct spi_mem and a hook is added to let controller
drivers set a custom name for the memory device.
Example for the FSL QSPI driver:
Name with the old driver: 21e0000.qspi,
or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ...
Name with the new driver without spi_mem_get_name: spi4.0
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de> Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-mem: Fix a typo in the documentation of struct spi_mem
Fix a typo in the @drvpriv description.
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Lorenzo Bianconi [Sat, 28 Jul 2018 08:19:14 +0000 (10:19 +0200)]
spi: spi-gpio: add SPI_3WIRE support
Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Lorenzo Bianconi [Sat, 28 Jul 2018 08:19:13 +0000 (10:19 +0200)]
spi: add flags parameter to txrx_word function pointers
Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Mark Brown <broonie@kernel.org>
The integration of the Designware SPI controller on Microsemi SoCs requires
an extra register set to be able to give the IP control of the SPI
interface.
Cc: Rob Herring <robh+dt@kernel.org> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: img-spfi: Set device select bits for SPFI port state
Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Mark Brown <broonie@kernel.org>
Colin Ian King [Mon, 30 Jul 2018 14:45:46 +0000 (15:45 +0100)]
spi: omap2-mcspi: remove several redundant variables
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Because the SPI controller deasserts the chip select when the TX fifo is
empty (which may happen in the middle of a transfer), the CS should be
handled by linux. Unfortunately, some or all of the first four chip
selects are not muxable as GPIOs, depending on the SoC.
There is a way to bitbang those pins by using the SPI boot controller so
use it to set the chip selects.
At init time, it is also necessary to give control of the SPI interface to
the Designware IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: imx: Use the longuest possible burst size when in dynamic_burst
Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.
This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.
With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).
The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.
With this method, the read_u32 field is no longer necessary, and is
removed.
This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.
This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.
This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: imx: Use dynamic bursts only when bits_per_word is 8, 16 or 32
The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.
This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.
With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org>
David Lechner [Tue, 17 Jul 2018 03:20:49 +0000 (22:20 -0500)]
spi: spi-bitbang: change flags from u8 to u16
This changes the data type of the flags field in struct spi_bitbang from
u8 to u16. This matches the size of the mode field of struct spi_device
where these flags are also used.
This is done in preparation of adding a new SPI mode flag that will be
used with this field that would otherwise not fit in 8 bits.
Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-fsl-dspi: Fill actual_length when doing DMA transfer
Upper layer users of SPI device drivers may rely on 'actual_length',
so it is important that information is correctly reported. One such
example is spi_mem_exec_op() function that will fail if
'actual_length' of the data transferred is not what was requested. Add
necessary code to populate 'actual_length.
Cc: Mark Brown <broonie@kernel.org> Cc: Sanchayan Maity <maitysanchayan@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: cphealy@gmail.com Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
spi: spi-fsl-dspi: Fix imprecise abort on VF500 during probe
Registers of DSPI should not be accessed before enabling its clock. On
Toradex Colibri VF50 on Iris carrier board this could be seen during
bootup as imprecise abort:
Unhandled fault: imprecise external abort (0x1c06) at 0x00000000
Internal error: : 1c06 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.39-dirty #97
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
[<804166a8>] (regmap_write) from [<80466b5c>] (dspi_probe+0x1f0/0x8dc)
[<8046696c>] (dspi_probe) from [<8040107c>] (platform_drv_probe+0x54/0xb8)
[<80401028>] (platform_drv_probe) from [<803ff53c>] (driver_probe_device+0x280/0x2f8)
[<803ff2bc>] (driver_probe_device) from [<803ff674>] (__driver_attach+0xc0/0xc4)
[<803ff5b4>] (__driver_attach) from [<803fd818>] (bus_for_each_dev+0x70/0xa4)
[<803fd7a8>] (bus_for_each_dev) from [<803fee74>] (driver_attach+0x24/0x28)
[<803fee50>] (driver_attach) from [<803fe980>] (bus_add_driver+0x1a0/0x218)
[<803fe7e0>] (bus_add_driver) from [<803fffe8>] (driver_register+0x80/0x100)
[<803fff68>] (driver_register) from [<80400fdc>] (__platform_driver_register+0x48/0x50)
[<80400f94>] (__platform_driver_register) from [<8091cf7c>] (fsl_dspi_driver_init+0x1c/0x20)
[<8091cf60>] (fsl_dspi_driver_init) from [<8010195c>] (do_one_initcall+0x4c/0x174)
[<80101910>] (do_one_initcall) from [<80900e8c>] (kernel_init_freeable+0x144/0x1d8)
[<80900d48>] (kernel_init_freeable) from [<805ff6a8>] (kernel_init+0x10/0x114)
[<805ff698>] (kernel_init) from [<80107be8>] (ret_from_fork+0x14/0x2c)
Cc: <stable@vger.kernel.org> Fixes: 5ee67b587a2b ("spi: dspi: clear SPI_SR before enable interrupt") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org>
Mika Westerberg [Thu, 28 Jun 2018 10:52:23 +0000 (13:52 +0300)]
spi: pxa2xx: Add support for Intel Ice Lake
Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org
spi: spi-fsl-dspi: Fix copy-paste error in dspi_probe
It seems that the proper structure field to use in this particular
case is *regmap_pushr* instead of regmap.
Addresses-Coverity-ID: 1470126 ("Copy-paste error") Fixes: 58ba07ec79e6 ("spi: spi-fsl-dspi: Add support for XSPI mode registers") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Esben Haabendal <eha@deif.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Esben Haabendal [Wed, 20 Jun 2018 07:34:42 +0000 (09:34 +0200)]
spi: spi-fsl-dspi: Enable extended SPI mode
Set the XSPI bit for devices configured for XSPI mode (currently LS1021A),
and thereby switch to extended SPI mode, allowing for SPI transfers using
from 4 to 32 bits per word instead of 4 to 16 bits per word.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Esben Haabendal [Wed, 20 Jun 2018 07:34:40 +0000 (09:34 +0200)]
spi: spi-fsl-dspi: XSPI FIFO handling (in TCFQ mode)
This implements handling of split CMD and TX FIFO queues for XSPI when
running in TCFQ mode.
It should be simple to add it to EOQ mode also. Currently, EOQ mode is
only used with coldfire. So if coldfire DSPI supports XSPI, XSPI FIFO
handling should be added to EOQ mode also.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Esben Haabendal [Wed, 20 Jun 2018 07:34:38 +0000 (09:34 +0200)]
spi: spi-fsl-dspi: Add support for XSPI mode registers
This prepares for adding support for extended SPI mode (XSPI), by extending
the regmap with the extra SREX and CTAREx registers.
An additional register map is made for allowing 16 bit access to CMD and TX
FIFO of the PUSHR register separately, which is also needed for XSPI mode
support.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Esben Haabendal [Wed, 20 Jun 2018 07:34:37 +0000 (09:34 +0200)]
spi: spi-fsl-dspi: Fix MCR register handling
The MCR register is not changed, so initialize it in dspi_init().
The exception is the CLR_TXF and CLR_RXF bits, which should be written to
before each transfer to make sure we start with empty FIFOs. With MCR
register now configured as volatile, the regmap_update_bits will do a real
read-modify-write cycle.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Esben Haabendal [Wed, 20 Jun 2018 07:34:35 +0000 (09:34 +0200)]
spi: spi-fsl-dspi: Support 4 to 16 bits per word transfers
This extends the driver with support for all SPI framesizes from 4 to 16
bits, and adds support for per transfer specific bits_per_word, while at
the same time reducing code size and complexity.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
This change brings handling of cs_change in line with the specification in
spi.h, implementing handling of transfer->cs_change for all transfers.
The value for CMD FIFO is precalculated with transfer->cs_change field
taken into account, allowing for CS de-activate between transfers and
keeping CS activated after last transfer.
Signed-off-by: Esben Haabendal <eha@deif.com> Acked-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jan Kundrát [Mon, 4 Jun 2018 14:34:25 +0000 (16:34 +0200)]
spi: orion: fix CS GPIO handling again
The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.
The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.
With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).
I tried to fix this in 544248623b95 already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz> Signed-off-by: Mark Brown <broonie@kernel.org>
Janek Kotas [Mon, 4 Jun 2018 11:24:44 +0000 (11:24 +0000)]
spi: cadence: Change usleep_range() to udelay(), for atomic context
The path "spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()" added a usleep_range() function call,
which cannot be used in atomic context.
However the cdns_spi_fill_tx_fifo() function can be called during
an interrupt which may result in a kernel panic:
spi: sh-msiof: Make sure all DMA operations have completed
In case of a bi-directional transfer, receive DMA may complete in the
rcar-dmac driver before transmit DMA, due to scheduling latencies.
As the MSIOF driver waits for completion of the receive DMA only, it may
submit the next transmit DMA request before the previous one has
completed.
Make the driver more robust by waiting for the completion of both
receive and transmit DMA, when applicable.
Based on a patch in the BSP by Ryo Kataoka.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sat, 16 Jun 2018 20:37:55 +0000 (05:37 +0900)]
Merge tag 'for-linus-20180616' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into -rc1. This contains:
- bsg_open vs bsg_unregister race fix (Anatoliy)
- NVMe pull request from Christoph, with fixes for regressions in
this window, FC connect/reconnect path code unification, and a
trace point addition.
- timeout fix (Christoph)
- remove a few unused functions (Christoph)
- blk-mq tag_set reinit fix (Roman)"
* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
bsg: fix race of bsg_open and bsg_unregister
block: remov blk_queue_invalidate_tags
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
blk-mq: don't time out requests again that are in the timeout handler
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
blk-mq: reinit q->tag_set_list entry only after grace period
Linus Torvalds [Sat, 16 Jun 2018 20:25:18 +0000 (05:25 +0900)]
Merge tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...
Linus Torvalds [Sat, 16 Jun 2018 20:06:18 +0000 (05:06 +0900)]
Merge tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify updates from Jan Kara:
"fsnotify cleanups unifying handling of different watch types.
This is the shortened fsnotify series from Amir with the last five
patches pulled out. Amir has modified those patches to not change
struct inode but obviously it's too late for those to go into this
merge window"
* tag 'fsnotify_for_v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fsnotify: add fsnotify_add_inode_mark() wrappers
fanotify: generalize fanotify_should_send_event()
fsnotify: generalize send_to_group()
fsnotify: generalize iteration of marks by object type
fsnotify: introduce marks iteration helpers
fsnotify: remove redundant arguments to handle_event()
fsnotify: use type id to identify connector object type
Linus Torvalds [Sat, 16 Jun 2018 07:32:04 +0000 (16:32 +0900)]
Merge branch 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull AFS updates from Al Viro:
"Assorted AFS stuff - ended up in vfs.git since most of that consists
of David's AFS-related followups to Christoph's procfs series"
* 'afs-proc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Optimise callback breaking by not repeating volume lookup
afs: Display manually added cells in dynamic root mount
afs: Enable IPv6 DNS lookups
afs: Show all of a server's addresses in /proc/fs/afs/servers
afs: Handle CONFIG_PROC_FS=n
proc: Make inline name size calculation automatic
afs: Implement network namespacing
afs: Mark afs_net::ws_cell as __rcu and set using rcu functions
afs: Fix a Sparse warning in xdr_decode_AFSFetchStatus()
proc: Add a way to make network proc files writable
afs: Rearrange fs/afs/proc.c to remove remaining predeclarations.
afs: Rearrange fs/afs/proc.c to move the show routines up
afs: Rearrange fs/afs/proc.c by moving fops and open functions down
afs: Move /proc management functions to the end of the file
Linus Torvalds [Sat, 16 Jun 2018 07:21:50 +0000 (16:21 +0900)]
Merge branch 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull compat updates from Al Viro:
"Some biarch patches - getting rid of assorted (mis)uses of
compat_alloc_user_space().
Not much in that area this cycle..."
* 'work.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
orangefs: simplify compat ioctl handling
signalfd: lift sigmask copyin and size checks to callers of do_signalfd4()
vmsplice(): lift importing iovec into vmsplice(2) and compat counterpart
Linus Torvalds [Sat, 16 Jun 2018 07:11:40 +0000 (16:11 +0900)]
Merge branch 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull aio fixes from Al Viro:
"Assorted AIO followups and fixes"
* 'work.aio' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
eventpoll: switch to ->poll_mask
aio: only return events requested in poll_mask() for IOCB_CMD_POLL
eventfd: only return events requested in poll_mask()
aio: mark __aio_sigset::sigmask const
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
Linus Torvalds [Fri, 15 Jun 2018 22:36:39 +0000 (07:36 +0900)]
Merge tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Minor code cleanup and also allow sig_enforce param to be shown in
sysfs with CONFIG_MODULE_SIG_FORCE"
* tag 'modules-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Allow to always show the status of modsign
module: Do not access sig_enforce directly
Linus Torvalds [Fri, 15 Jun 2018 21:42:43 +0000 (06:42 +0900)]
Merge tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V updates from Palmer Dabbelt:
"This contains some small RISC-V updates I'd like to target for 4.18.
They are all fairly small this time. Here's a short summary, there's
more info in the commits/merges:
- a fix to __clear_user to respect the passed arguments.
- enough support for the perf subsystem to work with RISC-V's ISA
defined performance counters.
- support for sparse and cleanups suggested by it.
- support for R_RISCV_32 (a relocation, not the 32-bit ISA).
- some MAINTAINERS cleanups.
- the addition of CONFIG_HVC_RISCV_SBI to our defconfig, as it's
always present.
I've given these a simple build+boot test"
* tag 'riscv-for-linus-4.18-merge_window' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Add CONFIG_HVC_RISCV_SBI=y to defconfig
RISC-V: Handle R_RISCV_32 in modules
riscv/ftrace: Export _mcount when DYNAMIC_FTRACE isn't set
riscv: add riscv-specific predefines to CHECKFLAGS
riscv: split the declaration of __copy_user
riscv: no __user for probe_kernel_address()
riscv: use NULL instead of a plain 0
perf: riscv: Add Document for Future Porting Guide
perf: riscv: preliminary RISC-V support
MAINTAINERS: Update Albert's email, he's back at Berkeley
MAINTAINERS: Add myself as a maintainer for SiFive's drivers
riscv: Fix the bug in memory access fixup code
Linus Torvalds [Fri, 15 Jun 2018 21:37:04 +0000 (06:37 +0900)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more kvm updates from Paolo Bonzini:
"Mostly the PPC part of the release, but also switching to Arnd's fix
for the hyperv config issue and a typo fix.
Main PPC changes:
- reimplement the MMIO instruction emulation
- transactional memory support for PR KVM
- improve radix page table handling"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (63 commits)
KVM: x86: VMX: redo fix for link error without CONFIG_HYPERV
KVM: x86: fix typo at kvm_arch_hardware_setup comment
KVM: PPC: Book3S PR: Fix failure status setting in tabort. emulation
KVM: PPC: Book3S PR: Enable use on POWER9 bare-metal hosts in HPT mode
KVM: PPC: Book3S PR: Don't let PAPR guest set MSR hypervisor bit
KVM: PPC: Book3S PR: Fix failure status setting in treclaim. emulation
KVM: PPC: Book3S PR: Fix MSR setting when delivering interrupts
KVM: PPC: Book3S PR: Handle additional interrupt types
KVM: PPC: Book3S PR: Enable kvmppc_get/set_one_reg_pr() for HTM registers
KVM: PPC: Book3S: Remove load/put vcpu for KVM_GET_REGS/KVM_SET_REGS
KVM: PPC: Remove load/put vcpu for KVM_GET/SET_ONE_REG ioctl
KVM: PPC: Move vcpu_load/vcpu_put down to each ioctl case in kvm_arch_vcpu_ioctl
KVM: PPC: Book3S PR: Enable HTM for PR KVM for KVM_CHECK_EXTENSION ioctl
KVM: PPC: Book3S PR: Support TAR handling for PR KVM HTM
KVM: PPC: Book3S PR: Add guard code to prevent returning to guest with PR=0 and Transactional state
KVM: PPC: Book3S PR: Add emulation for tabort. in privileged state
KVM: PPC: Book3S PR: Add emulation for trechkpt.
KVM: PPC: Book3S PR: Add emulation for treclaim.
KVM: PPC: Book3S PR: Restore NV regs after emulating mfspr from TM SPRs
KVM: PPC: Book3S PR: Always fail transactions in guest privileged state
...
Linus Torvalds [Fri, 15 Jun 2018 21:35:02 +0000 (06:35 +0900)]
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio, vhost: features, fixes
- PCI virtual function support for virtio
- DMA barriers for virtio strong barriers
- bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: update the comments for transport features
virtio_pci: support enabling VFs
vhost: fix info leak due to uninitialized memory
virtio_ring: switch to dma_XX barriers for rpmsg
The specified locations are not right. Fix the wildcard logic
to point to the correct directories.
Without that, get-maintainer won't get things right:
$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
After the patch, it will properly point to NPCM arch maintainers:
$ ./scripts/get_maintainer.pl --no-git-fallback --no-r --no-n --no-l -f Documentation/devicetree/bindings/arm/cpu-enable-method/nuvoton,npcm750-smp
avifishman70@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
tmaimon77@gmail.com (supporter:ARM/NUVOTON NPCM ARCHITECTURE)
robh+dt@kernel.org (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
mark.rutland@arm.com (maintainer:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS)
Cc: Avi Fishman <avifishman70@gmail.com> Cc: Tomer Maimon <tmaimon77@gmail.com> Cc: Patrick Venture <venture@google.com> Cc: Nancy Yuen <yuenn@google.com> Cc: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Jonathan Corbet <corbet@lwn.net>
kernel-parameters.txt: fix pointers to sound parameters
The alsa parameters file was renamed to alsa-configuration.rst.
With regards to OSS, it got retired as a hole by at changeset 727dede0ba8a ("sound: Retire OSS"). So, it doesn't make sense
to keep mentioning it at kernel-parameters.txt.
Some files, like tools/memory-model/README has references to
a Documentation file that is locale to it. Handle references
that are relative to them too.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Acked-by: Jonathan Corbet <corbet@lwn.net>
Roopa Prabhu [Wed, 13 Jun 2018 04:26:10 +0000 (21:26 -0700)]
neighbour: skip NTF_EXT_LEARNED entries during forced gc
Commit 9ce33e46531d ("neighbour: support for NTF_EXT_LEARNED flag")
added support for NTF_EXT_LEARNED for neighbour entries.
NTF_EXT_LEARNED entries are neigh entries managed by control
plane (eg: Ethernet VPN implementation in FRR routing suite).
Periodic gc already excludes these entries. This patch extends
it to forced gc which the earlier patch missed.
Fixes: 9ce33e46531d ("neighbour: support for NTF_EXT_LEARNED flag") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 15 Jun 2018 16:14:31 +0000 (09:14 -0700)]
Merge branch 'tls-fixes'
Daniel Borkmann says:
====================
Two tls fixes
First one is syzkaller trigered uaf and second one noticed
while writing test code with tls ulp. For details please see
individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 15 Jun 2018 01:07:46 +0000 (03:07 +0200)]
tls: fix waitall behavior in tls_sw_recvmsg
Current behavior in tls_sw_recvmsg() is to wait for incoming tls
messages and copy up to exactly len bytes of data that the user
provided. This is problematic in the sense that i) if no packet
is currently queued in strparser we keep waiting until one has been
processed and pushed into tls receive layer for tls_wait_data() to
wake up and push the decrypted bits to user space. Given after
tls decryption, we're back at streaming data, use sock_rcvlowat()
hint from tcp socket instead. Retain current behavior with MSG_WAITALL
flag and otherwise use the hint target for breaking the loop and
returning to application. This is done if currently no ctx->recv_pkt
is ready, otherwise continue to process it from our strparser
backlog.
Fixes: c46234ebb4d1 ("tls: RX path for ktls") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Dave Watson <davejwatson@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>