Ville Syrjälä [Wed, 6 Feb 2019 20:49:08 +0000 (22:49 +0200)]
drm/i915: Add pipe enable/disable tracepoints
Add tracepoints for pipe enable/disable. We'll include the
frame/scanline counters for all pipes in these tracepoints to
help in diagnosing underruns and whatnot when enabling/disabling
pipes in parallel with plane updates/flips on another pipe.
Ville Syrjälä [Wed, 6 Feb 2019 20:49:07 +0000 (22:49 +0200)]
drm/i915: Add pipe crc tracepoint
Add a tracepoint for pipe crc. Makes life much simpler when staring at
traces when hunting for fifo underruns and other issues which cause
corrupted frames. We'll add the tracepoint before filtering out any
potentially bogus crcs during modeset (should actually verify if that
filtering is even correct anymore...)
v2: s/crcs[5]/*crcs/ in the function argument because something
in the macros wants to do sizeof(crcs) and gcc likes to
warn us it's not an actual array so the size may not be
as expected. The silly bugger even does that for 'crcs[]'
causing us to lose any helpful syntactic hint that we
are in fact dealing with an array (kbuild test robot)
Chris Wilson [Wed, 13 Feb 2019 18:27:37 +0000 (18:27 +0000)]
drm/i915: Defer application of request banning to submission
As we currently do not check on submission whether the context is banned
in a timely manner it is possible for some requests to escape
cancellation after their parent context is banned. By moving the ban
into the request submission under the engine->timeline.lock, we
serialise it with the reset and setting of the context ban.
Chris Wilson [Wed, 13 Feb 2019 22:48:05 +0000 (22:48 +0000)]
drm/i915/selftests: Always use an active engine while resetting
Currently, we only try to reset a live engine for checking the whitelist
retention across a per-engine reset. For safety, it appears we need to
prime the system with a hanging spinner before performing a full-device
reset. (Figuring out the root cause behind the instability with handling
a reset during a no-op request is a challenge for another test, the
whitelist test has its own purpose.)
Chris Wilson [Wed, 13 Feb 2019 23:20:47 +0000 (23:20 +0000)]
drm/i915: Only try to park engines after a failed reset
Currently we try to stop the engine by programming the ring registers to
be disabled before we perform the reset. Sometimes, we see the context
image also have invalid ring registers, which one presumes may be
actually caused by us doing so. Lets risk not doing programming the
ring to zero on the first attempt to avoid preserving that corruption
into the context image, leaving the w/a in place for subsequent
reset attempts.
Chris Wilson [Wed, 13 Feb 2019 15:21:09 +0000 (15:21 +0000)]
snd/hda, drm/i915: Track the display_power_status using a cookie
drm/i915 is tracking all wakeref owners with a cookie in order to
identify leaks. To that end, each rpm acquisition ops->get_power is
assigned a cookie which should be passed to ops->put_power to signify
its release (and removal from the list of wakeref owners). As snd/hda is
already using a bool to track current status of display_power extending
that to an unsigned long to hold the boolean cookie is a trivial
extension, and will quell all doubt that snd/hda is the cause of the
device runtime pm leaks.
v2: Keep using the power abstraction for local wakeref tracking.
v3: BUILD_BUG_ON impedance mismatch
Ville Syrjälä [Wed, 13 Feb 2019 16:54:24 +0000 (18:54 +0200)]
drm/i915: Implement new w/a for underruns with wm1+ disabled
The new workaround from the hw team involves leaving WM1
still disabled but programming the blocks value
identically to WM0, and we also need to set the "ignore
lines watermark" bit for WM1.
Ville Syrjälä [Thu, 29 Nov 2018 17:55:04 +0000 (19:55 +0200)]
drm/i915: Assert that VED and ISP are power gated
As there are no upstream drivers for VED or ISP let's just
assert that they are power gated. Otherwise they would
prevent s0ix entry.
For ISP this is only relevant when it is not exposed as a
PCI device and instead is a subordinate of the gunit. When
exposed as a PCI device it will be handled by the
atomisp2_pm driver.
On my VLV FFRD8 board the firmware power gates both of these
by default. Let's assume that is always the case and just
WARN if we ever encounter something different.
Chris Wilson [Wed, 13 Feb 2019 09:25:04 +0000 (09:25 +0000)]
drm/i915: Apply rps waitboosting for dma_fence_wait_timeout()
As time goes by, usage of generic ioctls such as drm_syncobj and
sync_file are on the increase bypassing i915-specific ioctls like
GEM_WAIT. Currently, we only apply waitboosting to our driver ioctls as
we track the file/client and account the waitboosting to them. However,
since commit 7b92c1bd0540 ("drm/i915: Avoid keeping waitboost active for
signaling threads"), we no longer have been applying the client
ratelimiting on waitboosts and so that information has only been used
for debug tracking.
Push the application of waitboosting down to the common
i915_request_wait, and apply it to all foreign fence waits as well.
Uma Shankar [Mon, 11 Feb 2019 13:50:24 +0000 (19:20 +0530)]
drm/i915/icl: Enable pipe output csc
GEN11+ onwards an output csc hardware block has been added.
This is after the pipe gamma block and is in addition to the
legacy pipe CSC block. Primary use case for this block is to
convert RGB to YUV in case sink supports YUV.
This patch adds supports for the same.
v2: This is added after splitting the existing ICL pipe CSC
handling. As per Matt's suggestion, made this to co-exist
with existing pipe CSC, wherein both can be enabled if a
certain usecase arises.
v3: Fixed an issue with co-existence of output csc and normal
pipe csc, spotted by Matt. Put the csc mode flag enabling to
color_check to align with atomic.
v4: Fixed macro alignment and checkpatch complaints wrt line over
100 characters limit.
Uma Shankar [Mon, 11 Feb 2019 13:50:21 +0000 (19:20 +0530)]
drm/i915/glk: Fix degamma lut programming
Fixed the glk degamma lut programming which currently
was hard coding a linear lut all the time, making degamma
block of glk basically a pass through.
Currently degamma lut for glk is assigned as 0 in platform
configuration. Updated the same to 33 as per the hardware
capability. IGT tests for degamma were getting skipped due to
this, spotted by Swati.
ToDo: The current gamma/degamm lut ABI has just 16bit for each
color component. This is not enough for GLK+, since input
precision is increased to 3.16 which will need 19bit entries.
Chris Wilson [Tue, 12 Feb 2019 13:08:30 +0000 (13:08 +0000)]
drm/i915: Recursive i915_reset_trylock() verboten
We cannot nest i915_reset_trylock() as the inner may wait for the
I915_RESET_BACKOFF which in turn is waiting upon sync_srcu who is
waiting for our outermost lock. As we take the reset srcu around the
fence update, we have to defer taking it in i915_gem_fault() until after
we acquire the pin on the fence to avoid nesting. This is a little ugly,
but still works. If a reset occurs between i915_vma_pin_fence() and the
second reset lock, the reset will restore the fence register back to the
pinned value before the reset lock allows us to proceed (our mmap won't
be revoked as we haven't yet marked it as being a userfault as that
requires us to hold the reset lock), so the pagefault is still
serialised with the revocation in reset.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109605 Fixes: 2caffbf11762 ("drm/i915: Revoke mmaps and prevent access to fence registers across reset") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190212130831.14425-1-chris@chris-wilson.co.uk
Ville Syrjälä [Fri, 8 Feb 2019 20:05:27 +0000 (22:05 +0200)]
drm/i915: Dump skl+ watermark changes
Currently we're only dumping out the ddb allocation changes, let's do
the same for the watermarks. This should help with debugging underruns
and whatnot.
First I tried one line per plane per wm level, but that resulted in
an obnoxious amount of lines printed. So as a compromise I settled
on a four line format, each line containing a single watermark related
value (enable,lines,blocks,min_ddb_alloc) for all 8 levels (+trans wm).
It still produces quite a lot of output but I can't really see a way
around that because we simply have a lot of data to dump.
Let's also pimp the ddb debug to print the size of the allocations
too, not just their bounds. Makes it a bit easier to compare against
the watermarks.
Chris Wilson [Mon, 11 Feb 2019 20:46:47 +0000 (20:46 +0000)]
drm/i915: Reacquire priolist cache after dropping the engine lock
If we drop the engine lock, we may run execlists_dequeue which may free
the priolist. Therefore if we ever drop the execution lock on the
engine, we have to discard our cache and refetch the priolist to ensure
we do not use a stale pointer.
Chris Wilson [Mon, 11 Feb 2019 13:10:04 +0000 (13:10 +0000)]
drm/i915: Include the current timeline seqno for debugging execlists
While this is mainly only useful for ELSP[0], it is definitely useful to
know the current timeline seqno wrt to the queued set of requests for
that port, as this carries additional information above and beyond the
near-defunct global_seqno and global HWSP.
Chris Wilson [Mon, 11 Feb 2019 13:50:40 +0000 (13:50 +0000)]
drm/i915: Use synchronize_srcu_expedited() for resets
We impose upon ourselves a strict timeout for resets (to ensure forward
progress by use of a failsafe). Prefer to use the expedited
synchronisation function in this case to reduce the likelihood of a
spurious delay being treated as a deadlock.
Chris Wilson [Mon, 11 Feb 2019 13:50:39 +0000 (13:50 +0000)]
drm/i915: Pull sync_scru for device reset outside of wedge_mutex
We need to flush our srcu protecting resources about to be clobbered
by the reset, inside of our timer failsafe but outside of the
error->wedge_mutex, so that the failsafe can run in case the
synchronize_srcu() takes too long (hits a shrinker deadlock?).
Fixes: 72eb16df010a ("drm/i915: Serialise resets with wedging")
References: https://bugs.freedesktop.org/show_bug.cgi?id=109605 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190211135040.1234-1-chris@chris-wilson.co.uk Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Jani Nikula [Fri, 8 Feb 2019 18:42:53 +0000 (20:42 +0200)]
drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
Starting from opregion version 2.1 (roughly corresponding to ICL+) the
RVDA field is relative from the beginning of opregion, not absolute
address.
Fix the error path while at it.
v2: Make relative vs. absolute conditional on the opregion version,
bumped for the purpose. Turned out there are machines relying on
absolute RVDA in the wild.
v3: Fix the version checks
Fixes: 04ebaadb9f2d ("drm/i915/opregion: handle VBT sizes bigger than 6 KB") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Imre Deak <imre.deak@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190208184254.24123-2-jani.nikula@intel.com
Chris Wilson [Fri, 8 Feb 2019 13:47:04 +0000 (13:47 +0000)]
drm/i915: Protect i915_active iterators from the shrinker
If we allocate while iterating the rbtree of active nodes, we may hit
the shrinker and so retire the i915_active, reaping the rbtree. Modifying
the rbtree as we iterate is not good behaviour, so acquire the
i915_active first to keep the tree intact whenever we allocate.
Fixes: a42375af0a30 ("drm/i915: Release the active tracker tree upon idling") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190208134704.23039-1-chris@chris-wilson.co.uk Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Chris Wilson [Fri, 8 Feb 2019 23:51:08 +0000 (23:51 +0000)]
drm/i915/execlists: Refactor out can_merge_rq()
In the next patch, we add another user that wants to check whether
requests can be merge into a single HW execution, and in the future we
want to add more conditions under which requests from the same context
cannot be merge. In preparation, extract out can_merge_rq().
v2: Reorder tests to decide if we can continue filling ELSP and bonus
comments.
Chris Wilson [Fri, 8 Feb 2019 15:37:08 +0000 (15:37 +0000)]
drm/i915: Don't claim an unstarted request was guilty
If we haven't even begun executing the payload of the stalled request,
then we should not claim that its userspace context was guilty of
submitting a hanging batch.
v2: Check for context corruption before trying to restart.
v3: Preserve semaphores on skipping requests (need to keep the timelines
intact).
Chris Wilson [Fri, 8 Feb 2019 15:37:06 +0000 (15:37 +0000)]
drm/i915: Wait for old resets before applying debugfs/i915_wedged
Since we use the debugfs to recover the device after modifying the
i915.reset parameter, we need to be sure that we apply the reset and not
piggy-back onto a concurrent one in order for the parameter to take
effect.
Chris Wilson [Fri, 8 Feb 2019 15:37:05 +0000 (15:37 +0000)]
drm/i915: Uninterruptibly drain the timelines on unwedging
On wedging, we mark all executing requests as complete and all pending
requests completed as soon as they are ready. Before unwedging though we
wish to flush those pending requests prior to restoring default
execution, and so we must wait. Do so uninterruptibly as we do not provide
the EINTR gracefully back to userspace in this case but persists in
keeping the permanently wedged state without restarting the syscall.
Chris Wilson [Fri, 8 Feb 2019 15:37:04 +0000 (15:37 +0000)]
drm/i915: Force the GPU reset upon wedging
When declaring the GPU wedged, we do need to hit the GPU with the reset
hammer so that its state matches our presumed state during cleanup. If
the reset fails, it fails, and we may be unhappy but wedged. However, if
we are testing our wedge/unwedged handling, the desync carries over into
the next test and promptly explodes.
Chris Wilson [Fri, 8 Feb 2019 15:37:03 +0000 (15:37 +0000)]
drm/i915: Revoke mmaps and prevent access to fence registers across reset
Previously, we were able to rely on the recursive properties of
struct_mutex to allow us to serialise revoking mmaps and reacquiring the
FENCE registers with them being clobbered over a global device reset.
I then proceeded to throw out the baby with the bath water in order to
pursue a struct_mutex-less reset.
Perusing LWN for alternative strategies, the dilemma on how to serialise
access to a global resource on one side was answered by
https://lwn.net/Articles/202847/ -- Sleepable RCU:
No more worrying about stop_machine, just an uber-complex mutex,
optimised for reads, with the overhead pushed to the rare reset path.
However, we do run the risk of a deadlock as we allocate underneath the
SRCU read lock, and the allocation may require a GPU reset, causing a
dependency cycle via the in-flight requests. We resolve that by declaring
the driver wedged and cancelling all in-flight rendering.
v2: Use expedited rcu barriers to match our earlier timing
characteristics.
v3: Try to annotate locking contexts for sparse
v4: Reduce selftest lock duration to avoid a reset deadlock with fences
v5: s/srcu/reset_backoff_srcu/
v6: Remove more stale comments
Chris Wilson [Fri, 8 Feb 2019 15:37:02 +0000 (15:37 +0000)]
drm/i915: Defer removing fence register tracking to rpm wakeup
Currently, we may simultaneously release the fence register from both
fence_update() and i915_gem_restore_fences(). This is dangerous, so
defer the bookkeeping entirely to i915_gem_restore_fences() when the
device is asleep.
Ville Syrjälä [Thu, 7 Feb 2019 20:21:46 +0000 (22:21 +0200)]
drm/i915: Update DSPCNTR gamma/csc bits during crtc_enable()
On g4x+ we depend on the primary plane DSPCNTR gamma/csc enable
bits for the pipe bottom color. To guarantee that those are
correct already when enabling the crtc let's do an explicit
->disable_plane() call before enabling the pipe.
On skl+ this will be handled by the explicit PIPE_BOTTOM_COLOR
register which is already part of the normal color commit we
do durign crtc enable.
Ville Syrjälä [Thu, 7 Feb 2019 20:21:45 +0000 (22:21 +0200)]
drm/i915: Disable pipe gamma when C8 pixel format is used
Planes scanning out C8 will want to use the legacy lut as
their palette. That means the LUT content are unlikely to
be useful for gamma correction on other planes. Thus we
should disable pipe gamma for all the other planes. And
we should reject any non legacy LUT configurations when
C8 planes are present.
Fixes the appearance of the hw cursor when running
X -depth 8.
Note that CHV with it's independent CGM degamma/gamma LUTs
could probably use the CGM for gamma correction even when
the legacy LUT is used for C8. But that would require a
new uapi for configuring the legacy LUT and CGM LUTs at
the same time. Totally not worth it.
Ville Syrjälä [Thu, 7 Feb 2019 20:21:44 +0000 (22:21 +0200)]
drm/i915: Turn off pipe CSC when it's not needed
As with pipe gamma we can avoid the potential precision loss from
the pipe csc unit when there is no need to use it. And again
we need the same logic for updating the planes.
Ville Syrjälä [Thu, 7 Feb 2019 20:21:43 +0000 (22:21 +0200)]
drm/i915: Turn off pipe gamma when it's not needed
The pipe internal precision is higher than what we currently program to
the degamma/gamma LUTs. We can get a higher quality image by bypassing
the LUTs when they're not needed. Let's do that.
Each plane has its own control bit for this, so we have to update
all active planes. The way we've done this we don't actually have
to run through the whole .check_plane() thing. And we actually
do the .color_check() after .check_plane() so we couldn't even do
that without shuffling the code around.
Additionally on pre-skl we have to update the primary plane regardless
of whether it's active or not on account of the primary plane gamma
enable bit also affecting the pipe bottom color.
v2: Drop the '.' from patch title (Uma)
Fix 'primayr' typo (Uma,Matt)
Rebase
Ville Syrjälä [Thu, 7 Feb 2019 20:21:42 +0000 (22:21 +0200)]
drm/i915: Track pipe csc enable in crtc state
Just like we did for pipe gamma, let's also track the pipe csc
state. The hardware only exists on ILK+, and currently we always
enable it on hsw+ and never on any other platforms. Just like
with pipe gamma, the primary plane control register is used
for the readout on pre-SKL, and the pipe bottom color register
on SKL+.
v2: Rebase
v3: Allow fastboot with csc_enable changes (Maarten)
Deal with HAS_GMCH
Ville Syrjälä [Thu, 7 Feb 2019 20:39:13 +0000 (22:39 +0200)]
drm/i915: Track pipe gamma enable/disable in crtc state
Track whether pipe gamma is enabled or disabled. For now we
stick to the current behaviour of always enabling gamma. But
we do get working state readout for this now. On SKL+ we use
the pipe bottom color as our hardware state. On pre-SKL we
read the state back from the primary plane control register.
That only really correct for g4x+, as older platforms never
gamma correct pipe bottom color. But doing the readout the
same way on all platforms is fine, and there is no other way
to do it really.
v2: Initialize val at declaration (Uma)
Drop the bogus skl scaler comment change (Uma)
Rebase
v3: Allow fastboot with gamma_enable changes (Maarten)
v4: Drop the PIPE_BOTTOM_COLOR write from
intel_update_pipe_config() again. It snuck back in
during the rebase
Ville Syrjälä [Thu, 7 Feb 2019 20:21:40 +0000 (22:21 +0200)]
drm/i915: Populate gamma_mode for all platforms
On pre-HSW gamma mode is configured via PIPECONF. The bits are
the same except shifted up, so we can reuse just store them in
crtc_state->gamma_mode in the HSW+ way, allowing us to share
some code later.
v2: Allow fastboot with gamma_mode changes (Maarten)
Add space around the '<<' in the reg macro
Deal with HAS_GMCH
drm/i915/psr: Execute the default PSR code path when setting i915_edp_psr_debug
Changing the i915_edp_psr_debug was enabling, disabling or switching
PSR version by directly calling intel_psr_disable_locked() and
intel_psr_enable_locked(), what is not the default PSR path that will
be executed by real users.
So lets force a fastset in the PSR CRTC to trigger a pipe update and
stress the default code path.
Recently a bug was found when switching from PSR2 to PSR1 while
enable_psr kernel parameter was set to the default parameter, this
changes fix it and also fixes the bug linked bellow were DRRS was
left enabled together with PSR when enabling PSR from debugfs.
v2: Handling missing case: disabled to PSR1
v3: Not duplicating the whole atomic state(Maarten)
v4: Adding back the missing call to intel_psr_irq_control(Dhinakaran)
Ramalingam C [Mon, 4 Feb 2019 15:44:40 +0000 (21:14 +0530)]
drm/i915: HDCP state handling in ddi_update_pipe
The downgrade of the fullmodeset into fastset
intel_encoder->update_pipe, in possible scenario, skips the En/Dis-able
DDI. Hence breaks the HDCP state change handling.
We also don't have any hdcp tests in CI, because the shard runs don't
have hdcp capable outputs :-/
So this change fixs it by handling the HDCP state change request at
intel_encoder->update_pipe too along with enable and disable of the DDI.
Fixes: d19f958db23c ("drm/i915: Enable fastset for non-boot modesets.")
v2:
Added commit id that broke the HDCP [Daniel]
Ville Syrjälä [Tue, 5 Feb 2019 16:08:41 +0000 (18:08 +0200)]
drm/i915: Move LUT programming to happen after vblank waits
The LUTs are single buffered so we should program them after
the double buffered pipe updates have been latched by the
hardware.
We'll also fix up the IPS vs. split gamma w/a to do the IPS
disable like everyone else. Note that this is currently dead
code as we don't use the split gamma mode on HSW, but that
will be fixed up shortly.
Ville Syrjälä [Tue, 5 Feb 2019 16:08:40 +0000 (18:08 +0200)]
drm/i915: Split color mgmt based on single vs. double buffered registers
Split the color management hooks along the single vs. double
buffered registers line. Of the currently programmed registers
GAMMA_MODE and the ilk+ pipe CSC are double buffered, the
LUTS and CHV CGM block are single buffered.
The double buffered register will be programmed during the
normal pipe update with evasion, and also during pipe enable
so that the settings will already be correct when the pipe
starts up before the planes are enabled.
The single buffered registers are currently programmed before
the vblank evade. Which is totally wrong, but we'll correct
that later.
v2: Add some docs to explain the two vfuncs (Matt,Uma)
Rebase
Ville Syrjälä [Tue, 5 Feb 2019 16:08:39 +0000 (18:08 +0200)]
drm/i915: Pull GAMMA_MODE write out from haswell_load_luts()
For bdw+ let's move the GAMMA_MODE write for the legacy LUT
mode into the .load_luts() funciton directly, rather than
relying on haswell_load_luts(). We'll be getting rid of
haswell_load_luts() entirely soon, and it's anyway cleaner
to have the GAMMA_MODE write in a single place.
Ville Syrjälä [Tue, 5 Feb 2019 16:08:36 +0000 (18:08 +0200)]
drm/i915: Split the gamma/csc enable bits from the plane_ctl() function
On g4x+ the pipe gamma enable bit for the primary plane affects
the pipe bottom color as well. The same for the pipe csc enable
bit on ilk+. Thus we must configure those bits correctly even
when the primary plane is disabled.
To make the feasible let's split those settings from the
plane_ctl() function into a seprate funciton that we can
call from the ->disable_plane() hook as well.
For consistency we'll do that on all the plane types. While
that has no real benefits at this time, it'll become useful
when we start to control the pipe gamma/csc enable bits
dynamically when we overhaul the color management code.
On pre-g4x there doesn't appear to be any way to gamma
correct the pipe bottom color, but sticking to the same
pattern doesn't hurt. And it'll still help us to do
crtc state readout correctly for the pipe gamma enable
bit for the color management overhaul.
An alternative apporach would be to still precompute these
bits into plane_state->ctl, but that would require that we
run through the plane check even when the plane isn't logically
enabled on any crtc. Currently that condition causes us to
short circuit the entire thing and not call ->check_plane().
There would also be some chicken and egg problems with
->check_plane() vs. crtc color state check that would
requite splitting certain things into multiple steps.
So all in all this seems like the easier route.
Ville Syrjälä [Wed, 6 Feb 2019 18:54:33 +0000 (20:54 +0200)]
drm/i915: Don't set update_wm_post on g4x+
update_wm_post is meant for pre-g4x only. Don't ever set
it on g4x+.
The only effect of a bogus update_wm_post on g4x+ could
be that we clear the legacy_cursor_update flag in
intel_atomic_commit(). Since legacy_cursor_update is
only set for legacy cursor updates (as the name suggests)
and we only set update_wm_post for a modeset the two
cases should never occur at the same time. But let's
be consistent in setting update_wm_post so we don't
end up confusing so many people.
Chris Wilson [Thu, 7 Feb 2019 07:18:22 +0000 (07:18 +0000)]
drm/i915: Hack and slash, throttle execbuffer hogs
Apply backpressure to hogs that emit requests faster than the GPU can
process them by waiting for their ring to be less than half-full before
proceeding with taking the struct_mutex.
This is a gross hack to apply throttling backpressure, the long term
goal is to remove the struct_mutex contention so that each client
naturally waits, preferably in an asynchronous, nonblocking fashion
(pipelined operations for the win), for their own resources and never
blocks another client within the driver at least. (Realtime priority
goals would extend to ensuring that resource contention favours high
priority clients as well.)
This patch only limits excessive request production and does not attempt
to throttle clients that block waiting for eviction (either global GTT or
system memory) or any other global resources, see above for the long term
goal.
No microbenchmarks are harmed (to the best of my knowledge).
Testcase: igt/gem_exec_schedule/pi-ringfull-* Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190207071829.5574-1-chris@chris-wilson.co.uk
Lyude Paul [Tue, 29 Jan 2019 19:10:01 +0000 (14:10 -0500)]
drm/i915: Don't send hotplug in intel_dp_check_mst_status()
This hotplug also isn't needed: drm_dp_mst_topology_mgr_set_mst()
already sends a hotplug on its own from drm_dp_destroy_connector_work()
after destroying connectors in the MST topology.
Lyude Paul [Tue, 29 Jan 2019 19:10:00 +0000 (14:10 -0500)]
drm/i915: Don't send MST hotplugs during resume
We have a bad habit of calling drm_fb_helper_hotplug_event() far more
then we actually need to. MST appears to be one of these cases, where we
call drm_fb_helper_hotplug_event() if we fail to resume a connected MST
topology in intel_dp_mst_resume(). We don't actually need to do this at
all though since hotplug events are already sent from
drm_dp_connector_destroy_work() every time connectors are unregistered
from userspace's PoV. Additionally, extra calls to
drm_fb_helper_hotplug_event() also just mean more of a chance of doing a
connector probe somewhere we shouldn't.
So, don't send any hotplug events during resume if the MST topology
fails to come up. Just rely on the DP MST helpers to send them for us.
Lyude Paul [Tue, 29 Jan 2019 19:09:59 +0000 (14:09 -0500)]
drm/i915: Block fbdev HPD processing during suspend
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: 0e32b39ceed6 ("drm/i915: add DP 1.2 MST support (v0.7)") Cc: Todd Previte <tprevite@gmail.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v3.17+ Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-2-lyude@redhat.com
Ville Syrjälä [Tue, 5 Feb 2019 20:50:55 +0000 (22:50 +0200)]
drm/i915: Bump skl+ wm blocks to 11 bits
On icl the plane watermark blocks field is 11 bits. Bump our define to
match so that readout won't ignore the extra bit. We can safely do this
for older platforms too since the unused bits are hardwired to zero.
Tvrtko Ursulin [Tue, 5 Feb 2019 13:03:53 +0000 (13:03 +0000)]
drm/i915/pmu: Fix enable count array size and bounds checking
Enable count array is supposed to have one counter for each possible
engine sampler. As such, array sizing and bounds checking is not correct
and would blow up the asserts if more samplers were added.
No ill-effect in the current code base but lets fix it for correctness.
At the same time tidy the assert for readability and robustness.
Ville Syrjälä [Mon, 4 Feb 2019 20:22:32 +0000 (22:22 +0200)]
drm/i915: W/A for underruns with WM1+ disabled on icl
Disabling WM1+ on ICL causes tons of underruns with
linear/X-tiled framebuffers. We can avoid this by flipping
on a chicken bit affecting the way the hw fill the FIFO.
This may not be the final solution but should hopefully
avoid some underruns in the meantime.
Ville Syrjälä [Tue, 5 Feb 2019 15:50:53 +0000 (17:50 +0200)]
drm/i915: Fix wm latency==0 disable on skl+
When adding the early latency==0 check back I neglected to
realize that we no longer have a way to return a failure
from the wm computation like we had in the past (since we
now calculate wms before ddb allocations). Also plane_en
being false doesn't actually indicate that the level is
invalid as it wil also happen when the plane is not
enabled.
skl_allocate_pipe_ddb() starts scanning from the maximum
watermark level and it stops as soon as it finds a level
that is deemed viable. The assumption being that if level
n+1 is valid then level n is valid as well. Thus if we
now disable any watermark level by zeroing its latency
the code will think that level to be actually valid
and won't confirm whether the actually enabled lower
watermark level(s) actually fit into the allotted ddb
space. This results in hilarious watermark values that
exceed the ddb allocation of the plane.
The way we must now indicate a failure is to assign an
unreasoanbly big value to min_ddb_alloc which will then
make skl_allocate_pipe_ddb() reject the entire level.
v2: Also do the same for the lines>31 case (Matt)
v3: Make 'blocks' u32 (Matt)
Chris Wilson [Tue, 5 Feb 2019 09:27:59 +0000 (09:27 +0000)]
drm/i915: Push clear_intel_crtc_state() onto the heap
clear_intel_crtc_state() uses the stack for saving a temporary copy of
certain bits of the inherited crtc_state before clearing the unwanted
bits. This pushes it over the stack limit for my little 32b Pineview,
so move the temporary allocation to the heap instead. As we now use a
zeroed struct, we can copy the whole extended state back to both
preserve what bits need to be preserved and zero the rest.
Ville Syrjälä [Mon, 4 Feb 2019 21:16:44 +0000 (23:16 +0200)]
drm/i915: Include register polling in reg_rw traces
We generally omit register polling from the i915_reg_rw tracepoint.
Understandable since polling could generate a lot of noise in the
trace. The downside is that the trace is incomplete. As a compromise
let's trace the final register value observed while polling. That
should be generally sufficient to observe what the code should be
doing next.
I suppose in some cases it might make sense to also trace the initial
register value, and maybe the number of times we polled. But that
would require a separate tracepoint so let's leave it for the future.
The other users of _NOTRACE() are i915_pmu and i2c bitbanging,
which I decided to leave alone.
Next we should do something to claw back the tracepoints for
planes and whatnot which were switched to _FW() a while back.
I guess just new macros for raw_rw+trace. The question is
what to call it?
drm/i915: do not return invalid pointers as a *dentry
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Rodrigo Vivi [Mon, 4 Feb 2019 22:25:38 +0000 (14:25 -0800)]
drm/i915: Rename HAS_GMCH
First of all GMCH can be considered a feature by itself
since it is a chip present in some platforms that connects
the IA processor to memory and other components in PC.
Also with the introduction of display block at device info,
we got a redundant definition:
.display.has_gmch_display = 1,
So, let's clean up things a bit and use the standardized
way of has_feature on displays side.
No functional change and no manual interaction to generate
this patch.
It is only:
sed -si -e 's/has_gmch_display/has_gmch/g' \
-e 's/HAS_GMCH_DISPLAY/HAS_GMCH/g' drivers/gpu/drm/i915/*{c,h}
Chris Wilson [Tue, 5 Feb 2019 13:00:05 +0000 (13:00 +0000)]
drm/i915: Pull i915_gem_active into the i915_active family
Looking forward, we need to break the struct_mutex dependency on
i915_gem_active. In the meantime, external use of i915_gem_active is
quite beguiling, little do new users suspect that it implies a barrier
as each request it tracks must be ordered wrt the previous one. As one
of many, it can be used to track activity across multiple timelines, a
shared fence, which fits our unordered request submission much better. We
need to steer external users away from the singular, exclusive fence
imposed by i915_gem_active to i915_active instead. As part of that
process, we move i915_gem_active out of i915_request.c into
i915_active.c to start separating the two concepts, and rename it to
i915_active_request (both to tie it to the concept of tracking just one
request, and to give it a longer, less appealing name).
Chris Wilson [Tue, 5 Feb 2019 13:00:03 +0000 (13:00 +0000)]
drm/i915: Release the active tracker tree upon idling
As soon as we detect that the active tracker is idle and we prepare to
call the retire callback, release the storage for our tree of
per-timeline nodes. We expect these to be infrequently used and quick
to allocate, so there is little benefit in keeping the tree cached and
we would prefer to return the pages back to the system in a timely
fashion.
This also means that when we finalize the struct as a whole, we know as
the activity tracker must be idle, the tree has already been released.
Indeed we can reduce i915_active_fini() just to the assertions that there
is nothing to do.
Chris Wilson [Tue, 5 Feb 2019 13:00:02 +0000 (13:00 +0000)]
drm/i915: Generalise GPU activity tracking
We currently track GPU memory usage inside VMA, such that we never
release memory used by the GPU until after it has finished accessing it.
However, we may want to track other resources aside from VMA, or we may
want to split a VMA into multiple independent regions and track each
separately. For this purpose, generalise our request tracking (akin to
struct reservation_object) so that we can embed it into other objects.
Tvrtko Ursulin [Tue, 5 Feb 2019 09:50:31 +0000 (09:50 +0000)]
drm/i915: Expose RPCS (SSEU) configuration to userspace (Gen11 only)
We want to allow userspace to reconfigure the subslice configuration on a
per context basis.
This is required for the functional requirement of shutting down non-VME
enabled sub-slices on Gen11 parts.
To do so, we expose a context parameter to allow adjustment of the RPCS
register stored within the context image (and currently not accessible via
LRI).
If the context is adjusted before first use or whilst idle, the adjustment
is for "free"; otherwise if the context is active we queue a request to do
so (using the kernel context), following all other activity by that
context, which is also marked as barrier for all following submission
against the same context.
Since the overhead of device re-configuration during context switching can
be significant, especially in multi-context workloads, we limit this new
uAPI to only support the Gen11 VME use case. In this use case either the
device is fully enabled, and exactly one slice and half of the subslices
are enabled.
/* Set VME configuration on a 1x6x8 part. */
sseu.slice_mask = 0x1;
sseu.subslice_mask = 0xe0;
gem_context_set_param(fd, &arg);
v2: Fix offset of CTX_R_PWR_CLK_STATE in intel_lr_context_set_sseu()
(Lionel)
v3: Add ability to program this per engine (Chris)
v4: Move most get_sseu() into i915_gem_context.c (Lionel)
v5: Validate sseu configuration against the device's capabilities (Lionel)
v6: Change context powergating settings through MI_SDM on kernel context
(Chris)
v7: Synchronize the requests following a powergating setting change using
a global dependency (Chris)
Iterate timelines through dev_priv.gt.active_rings (Tvrtko)
Disable RPCS configuration setting for non capable users
(Lionel/Tvrtko)
v8: s/union intel_sseu/struct intel_sseu/ (Lionel)
s/dev_priv/i915/ (Tvrtko)
Change uapi class/instance fields to u16 (Tvrtko)
Bump mask fields to 64bits (Lionel)
Don't return EPERM when dynamic sseu is disabled (Tvrtko)
v9: Import context image into kernel context's ppgtt only when
reconfiguring powergated slice/subslices (Chris)
Use aliasing ppgtt when needed (Michel)
Tvrtko Ursulin:
v10:
* Update for upstream changes.
* Request submit needs a RPM reference.
* Reject on !FULL_PPGTT for simplicity.
* Pull out get/set param to helpers for readability and less indent.
* Use i915_request_await_dma_fence in add_global_barrier to skip waits
on the same timeline and avoid GEM_BUG_ON.
* No need to explicitly assign a NULL pointer to engine in legacy mode.
* No need to move gen8_make_rpcs up.
* Factored out global barrier as prep patch.
* Allow to only CAP_SYS_ADMIN if !Gen11.
v11:
* Remove engine vfunc in favour of local helper. (Chris Wilson)
* Stop retiring requests before updates since it is not needed
(Chris Wilson)
* Implement direct CPU update path for idle contexts. (Chris Wilson)
* Left side dependency needs only be on the same context timeline.
(Chris Wilson)
* It is sufficient to order the timeline. (Chris Wilson)
* Reject !RCS configuration attempts with -ENODEV for now.
v12:
* Rebase for make_rpcs.
v13:
* Centralize SSEU normalization to make_rpcs.
* Type width checking (uAPI <-> implementation).
* Gen11 restrictions uAPI checks.
* Gen11 subslice count differences handling.
Chris Wilson:
* args->size handling fixes.
* Update context image from GGTT.
* Postpone context image update to pinning.
* Use i915_gem_active_raw instead of last_request_on_engine.
v14:
* Add activity tracker on intel_context to fix the lifetime issues
and simplify the code. (Chris Wilson)
v15:
* Fix context pin leak if no space in ring by simplifying the
context pinning sequence.
v16:
* Rebase for context get/set param locking changes.
* Just -ENODEV on !Gen11. (Joonas)
v17:
* Fix one Gen11 subslice enablement rule.
* Handle error from i915_sw_fence_await_sw_fence_gfp. (Chris Wilson)
v18:
* Update commit message. (Joonas)
* Restrict uAPI to VME use case. (Joonas)
v19:
* Rebase.
v20:
* Rebase for ce->active_tracker.
v21:
* Rebase for IS_GEN changes.
v22:
* Reserve uAPI for flags straight away. (Chris Wilson)
v23:
* Rebase for RUNTIME_INFO.
v24:
* Added some headline docs for the uapi usage. (Joonas/Chris)
v25:
* Renamed class/instance to engine_class/engine_instance to avoid clash
with C++ keyword. (Tony Ye)
v26:
* Rebased for runtime pm api changes.
v27:
* Rebased for intel_context_init.
* Wrap commit msg to 75.
v28:
(Chris Wilson)
* Use i915_gem_ggtt.
* Use i915_request_await_dma_fence to show a better example.
v29:
* i915_timeline_set_barrier can now fail. (Chris Wilson)
v30:
* Capture some acks.
v31:
* Drop the WARN_ON from use controllable paths. (Chris Wilson)
* Use overflows_type for all checks.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100899
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107634
Issue: https://github.com/intel/media-driver/issues/267 Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Zhipeng Gong <zhipeng.gong@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Tony Ye <tony.ye@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Acked-by: Timo Aaltonen <timo.aaltonen@canonical.com> Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Stéphane Marchesin <marcheu@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190205095032.22673-4-tvrtko.ursulin@linux.intel.com
Tvrtko Ursulin [Tue, 5 Feb 2019 09:50:30 +0000 (09:50 +0000)]
drm/i915: Add timeline barrier support
Timeline barrier allows serialization between different timelines.
After calling i915_timeline_set_barrier with a request, all following
submissions on this timeline will be set up as depending on this request,
or barrier. Once the barrier has been completed it automatically gets
cleared and things continue as normal.
This facility will be used by the upcoming context SSEU code.
v2:
* Assert barrier has been retired on timeline_fini. (Chris Wilson)
* Fix mock_timeline.
v3:
* Improved comment language. (Chris Wilson)
v4:
* Maintain ordering with previous barriers set on the timeline.
drm/i915/perf: lock powergating configuration to default when active
If some of the contexts submitting workloads to the GPU have been
configured to shutdown slices/subslices, we might loose the NOA
configurations written in the NOA muxes.
One possible solution to this problem is to reprogram the NOA muxes
when we switch to a new context. We initially tried this in the
workaround batchbuffer but some concerns where raised about the cost
of reprogramming at every context switch. This solution is also not
without consequences from the userspace point of view. Reprogramming
of the muxes can only happen once the powergating configuration has
changed (which happens after context switch). This means for a window
of time during the recording, counters recorded by the OA unit might
be invalid. This requires userspace dealing with OA reports to discard
the invalid values.
Minimizing the reprogramming could be implemented by tracking of the
last programmed configuration somewhere in GGTT and use MI_PREDICATE
to discard some of the programming commands, but the command streamer
would still have to parse all the MI_LRI instructions in the
workaround batchbuffer.
Another solution, which this change implements, is to simply disregard
the user requested configuration for the period of time when i915/perf
is active.
On most platforms there are no issues with this apart from a performance
penality for some media workloads that benefit from running on a partially
powergated GPU. We already prevent RC6 from affecting the programming so
it doesn't sound completely unreasonable to hold on powergating for the
same reason.
On Icelake however there would a functional problem if the slices not-
containing the VME block were left enabled with a running media workload
which explicitly disabled them. To avoid a GPU hang in this case, on
Icelake we lock the enablement to only slices which contain VME blocks.
Downside is that it means degraded GPU performance when OA is active but
there is no known alternative solution for this.
v2: Leave RPCS programming in intel_lrc.c (Lionel)
v3: Update for s/union intel_sseu/struct intel_sseu/ (Lionel)
More to_intel_context() (Tvrtko)
s/dev_priv/i915/ (Tvrtko)
Tvrtko Ursulin:
v4:
* Rebase for make_rpcs changes.
v5:
* Apply OA restriction from make_rpcs directly.
v6:
* Rebase for context image setup changes.
v7:
* Move stream assignment before metric enable.
drm/i915: Record the sseu configuration per-context & engine
We want to expose the ability to reconfigure the slices, subslice and
eu per context and per engine. To facilitate that, store the current
configuration on the context for each engine, which is initially set
to the device default upon creation.
v2: record sseu configuration per context & engine (Chris)
v3: introduce the i915_gem_context_sseu to store powergating
programming, sseu_dev_info has grown quite a bit (Lionel)
v4: rename i915_gem_sseu into intel_sseu (Chris)
use to_intel_context() (Chris)
v5: More to_intel_context() (Tvrtko)
Switch intel_sseu from union to struct (Tvrtko)
Move context default sseu in existing loop (Chris)
Chris Wilson [Mon, 4 Feb 2019 15:01:01 +0000 (15:01 +0000)]
drm/i915: Trim NEWCLIENT boosting
Limit the NEWCLIENT boost to only give its small priority boost to fresh
clients only that have no dependencies.
The idea for using NEWCLIENT boosting, commit b16c765122f9 ("drm/i915:
Priority boost for new clients"), is that short-lived streams are often
interactive and require lower latency -- and that by executing those
ahead of the long running hogs, the short-lived clients do little to
interfere with the system throughput by virtue of their short-lived
nature. However, we were only considering the client's own timeline for
determining whether or not it was a fresh stream. This allowed for
compositors to wake up before their vblank and bump all of its client
streams. However, in testing with media-bench this results in chaining
all cooperating contexts together preventing us from being able to
reorder contexts to reduce bubbles (pipeline stalls), overall increasing
latency, and reducing system throughput. The exact opposite of our
intent. The compromise of applying the NEWCLIENT boost to strictly fresh
clients (that do not wait upon anything else) should maintain the
"real-time response under load" characteristics of FQ_CODEL, without
locking together the long chains of dependencies across the system.
Chris Wilson [Mon, 4 Feb 2019 08:41:05 +0000 (08:41 +0000)]
drm/i915: Allow normal clients to always preempt idle priority clients
When first enabling preemption, we hesitated from making it a free-for-all
where every higher priority client would force a preempt-to-idle cycle
and take over from all lower priority clients. We hesitated because we
were uncertain just how well preemption would work in practice, whether
the preemption latency itself would detract from the latency gains for
higher priority tasks and whether it would work at all. Since
introducing preemption, we have been enabling it for more common tasks,
even giving normal clients a small preemptive boost when they first
start (to aide fairness and improve interactivity). Now lets take one
step further and give permission for all normal (priority:0) clients to
preempt any idle (priority:<0) task so that users running long compute
jobs do not overly impact other jobs (i.e. their desktop) and the system
remains responsive under such idle loads.
References: f6322eddaff7 ("drm/i915/preemption: Allow preemption between submission ports")
References: b16c765122f9 ("drm/i915: Priority boost for new clients") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: Michał Winiarski <michal.winiarski@intel.com> Cc: "Bloomfield, Jon" <jon.bloomfield@intel.com> Cc: "Stead, Alan" <alan.stead@intel.com> Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190204084116.3013-1-chris@chris-wilson.co.uk
Hans de Goede [Tue, 29 Jan 2019 14:22:37 +0000 (15:22 +0100)]
drm/i915: Enable fastboot by default on VLV and CHV
We really want to have fastboot enabled by default to avoid an ugly
modeset during boot.
Currently we are enabling fastboot by default on gen9+ (Skylake and newer).
The intention is to enable it on older generations after it has seen more
testing on gen9+.
VLV and CHV devices are still being sold in stores today, as such it is
desirable to also enable fastboot by default on these now.
I've extensively tested fastboot=1 support on over 50 different
Bay- and Cherry-Trail devices. Testing DSI and eDP panels as well as
HDMI output (and even DP over Type-C on one device).
All 50 devices work fine with fastboot=1. On 2 devices their DSI panel
turns black as soon as the i915 driver loads when fastboot=0, so having
fastboot enabled is required for these 2 to work properly (for lack of
a better fix).
This restores the workaround that was reverted in c358514ba8da
("Revert "drm/i915/icl: WaEnableFloatBlendOptimization"").
The revert was due to the register write seemingly not sticking,
but the HW team has confirmed that this is because the
register is WO and that the workaround is indeed required.
Here the wa is added with a mask of 0 since the register is WO.
References: https://hsdes.intel.com/resource/1408134172
References: https://bugs.freedesktop.org/show_bug.cgi?id=107338 Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: Talha Nassar <talha.nassar@intel.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/1548983324-15344-4-git-send-email-talha.nassar@intel.com
Tvrtko Ursulin [Fri, 1 Feb 2019 01:08:42 +0000 (17:08 -0800)]
drm/i915: Move workaround infrastructure code up
Top comment in intel_workarounds.c says common code should come first so
lets respect that. Also, by moving the common code together opportunities
to reduce duplication will become more obvious.
Imre Deak [Mon, 28 Jan 2019 11:42:42 +0000 (13:42 +0200)]
drm/i915/icl: Add TypeC ports only if VBT is present
We can't safely probe Type C ports, whether they are a legacy or a
USB/Thunderbolt DP Alternate Type C port. This would require performing
the TypeC connect sequence - as described by the specification - but
that may have unwanted side-effects. These side-effects include at least
- without completeness - timeouts during AUX power well enabling and
subsequent PLL enabling errors.
To safely identify these ports we really need VBT, which has the proper
flag for this (ddi_vbt_port_info::supports_typec_usb, supports_tbt).
Based on the above disable Type C ports if we can't load VBT for some
reason.
v2:
- Notice that we disable TypeC ports completely and simplify accordingly
(Jose).
- Add code comment explaining why we disabled the ports. (Jani)
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> Cc: Jose Roberto de Souza <jose.souza@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190128114242.28666-1-imre.deak@intel.com
Ville Syrjälä [Wed, 30 Jan 2019 18:13:59 +0000 (20:13 +0200)]
drm/i915: Pick the first unused PLL once again
commit 5b0bd14dcc6b ("drm/i915/icl: keep track of unused pll while
looping") inadvertently (I presume) changed the code to pick the
last unused dpll rather than the first unused one like we did before.
While there should most likely be no harm in changing the order
let's change back just to avoid a change in the behaviour. At
least it might reduce the confusion when staring at logs (took
me a while to figure out why DPLL1 being picked over DPLL0
when the latter was most definitely available).
Matt Roper [Wed, 30 Jan 2019 18:10:22 +0000 (10:10 -0800)]
drm/i915: Apply LUT validation checks to platforms more accurately (v3)
Use of the new DRM_COLOR_LUT_NON_DECREASING test was a bit over-zealous;
it doesn't actually need to be applied to the degamma on "bdw-style"
platforms. Likewise, we overlooked the fact that CHV should have that
test applied to the gamma LUT as well as the degamma LUT.
Rather than adding more complicated platform checking to
intel_color_check(), let's just store the appropriate set of LUT
validation flags for each platform in the intel_device_info structure.
v2:
- Shuffle around LUT size tests so that the hardware-specific tests
won't be applied to legacy gamma tables. (Ville)
- Add a debug message so that it will be easier to understand why an
atomic transaction involving incorrectly-sized LUT's got rejected
by the driver.
v3:
- Switch size_t's to int's. (Ville)
Fixes: 85e2d61e4976 ("drm/i915: Validate userspace-provided color management LUT's (v4)")
References: https://lists.freedesktop.org/archives/intel-gfx/2019-January/187634.html Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190130181022.4291-1-matthew.d.roper@intel.com
Matt Roper [Wed, 30 Jan 2019 18:51:20 +0000 (10:51 -0800)]
drm/i915: Force background color to black for gen9+ (v2)
We don't yet allow userspace to control the CRTC background color, but
we should manually program the color to black to ensure the BIOS didn't
leave us with some other color. We should also set the pipe gamma and
pipe CSC bits so that the background color goes through the same color
management transformations that a plane with black pixels would.
v2: Rename register to SKL_BOTTOM_COLOR to more closely follow
bspec naming. (Ville)