====================
net: systemport: Fix padding vs. TSB insertion
This patch series fixes how we pad the packets submitted to the SYSTEMPORT
adapter, and how the transmit status block (prepended 8 bytes) fits in the
picture. The first patch is not technically a bug fix, but is required for the
second path to be applied and to greatly simplify the skb length calculation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Inserting the TSB means adding an extra 8 bytes in front the of packet
that is going to be used as metadata information by the TDMA engine, but
stripped off, so it does not really help with the packet padding.
For some odd packet sizes that fall below the 60 bytes payload (e.g: ARP)
we can end-up padding them after the TSB insertion, thus making them 64
bytes, but with the TDMA stripping off the first 8 bytes, they could
still be smaller than 64 bytes which is required to ingress the switch.
Fix this by swapping the padding and TSB insertion, guaranteeing that
the packets have the right sizes.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Since we need to pad our packets, utilize skb_put_padto() which
increases skb->len by how much we need to pad, allowing us to eliminate
the test on skb->len right below.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Pitre [Tue, 3 Jan 2017 18:57:00 +0000 (13:57 -0500)]
LiquidIO VF: s/select/imply/ for PTP_1588_CLOCK
Fix a minor fallout from the merge of the timers and the networking
trees. The following error may result if the PTP_1588_CLOCK
prerequisites are not available:
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0a5): undefined reference to `pps_unregister_source'
drivers/built-in.o: In function `ptp_clock_unregister':
(.text+0x40e0cc): undefined reference to `posix_clock_unregister'
drivers/built-in.o: In function `ptp_clock_event':
(.text+0x40e249): undefined reference to `pps_event'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e5e1): undefined reference to `pps_register_source'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e62c): undefined reference to `posix_clock_register'
drivers/built-in.o: In function `ptp_clock_register':
(.text+0x40e68d): undefined reference to `pps_unregister_source'
Signed-off-by: Nicolas Pitre <nico@linaro.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Chen [Tue, 3 Jan 2017 09:22:20 +0000 (17:22 +0800)]
net: usb: asix_devices: add .reset_resume for USB PM
The USB core may call reset_resume when it fails to resume asix device.
And USB core can recovery this abnormal resume at low level driver,
the same .resume at asix driver can work too. Add .reset_resume can
avoid disconnecting after backing from system resume, and NFS can
still be mounted after this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 3 Jan 2017 17:37:55 +0000 (09:37 -0800)]
net: vrf: Add missing Rx counters
The move from rx-handler to L3 receive handler inadvertantly dropped the
rx counters. Restore them.
Fixes: 74b20582ac38 ("net: l3mdev: Add hook in ip and ipv6") Reported-by: Dinesh Dutt <ddutt@cumulusnetworks.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Reiter Wolfgang [Tue, 3 Jan 2017 00:39:10 +0000 (01:39 +0100)]
drop_monitor: consider inserted data in genlmsg_end
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Tue, 3 Jan 2017 15:26:04 +0000 (16:26 +0100)]
benet: stricter vxlan offloading check in be_features_check
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dceed ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Mon, 2 Jan 2017 21:32:54 +0000 (13:32 -0800)]
ipv4: Do not allow MAIN to be alias for new LOCAL w/ custom rules
In the case of custom rules being present we need to handle the case of the
LOCAL table being intialized after the new rule has been added. To address
that I am adding a new check so that we can make certain we don't use an
alias of MAIN for LOCAL when allocating a new table.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse") Reported-by: Oliver Brunel <jjk@jjacky.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Folta [Mon, 2 Jan 2017 12:41:50 +0000 (12:41 +0000)]
net: macb: Updated resource allocation function calls to new version of API.
Changed function calls of resource allocation to new API. Changed way
of setting DMA mask. Removed unnecessary sanity check.
This patch is sent in regard to recently applied patch
Commit 83a77e9ec4150ee4acc635638f7dedd9da523a26
net: macb: Added PCI wrapper for Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 3 Jan 2017 14:33:00 +0000 (09:33 -0500)]
Merge branch 'dwmac-oxnas-leaks'
Johan Hovold says:
====================
net: stmmac: dwmac-oxnas: fix leaks and simplify pm
These patches fixes of-node and fixed-phydev leaks in the recently added
dwmac-oxnas driver, and ultimately switches over to using the generic pm
implementation as the required callbacks are now in place.
Note that this series has only been compile tested.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by calling the new glue
helper function.
For driver unbind, use the generic stmmac-platform remove implementation
and add an exit callback to disable the clock.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hovold [Mon, 2 Jan 2017 11:56:02 +0000 (12:56 +0100)]
net: stmmac: dwmac-oxnas: fix of-node leak
Use the syscon lookup-by-phandle helper so that the reference taken by
of_parse_phandle() is released when done with the node.
Fixes: 5ed7414062e7 ("net: stmmac: Add OXNAS Glue Driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Tesar [Mon, 2 Jan 2017 13:38:36 +0000 (14:38 +0100)]
igmp: Make igmp group member RFC 3376 compliant
5.2. Action on Reception of a Query
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Kumlien [Mon, 2 Jan 2017 08:18:35 +0000 (09:18 +0100)]
flow_dissector: Update pptp handling to avoid null pointer deref.
__skb_flow_dissect can be called with a skb or a data packet, either
can be NULL. All calls seems to have been moved to __skb_header_pointer
except the pptp handling which is still calling skb_header_pointer.
Fixes: ab10dccb1160 ("rps: Inspect PPTP encapsulated by GRE to get flow hash") Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 2 Jan 2017 10:19:29 +0000 (11:19 +0100)]
mac80211: initialize fast-xmit 'info' later
In ieee80211_xmit_fast(), 'info' is initialized to point to the skb
that's passed in, but that skb may later be replaced by a clone (if
it was shared), leading to an invalid pointer.
This can lead to use-after-free and also later crashes since the
real SKB's info->hw_queue doesn't get initialized properly.
Fix this by assigning info only later, when it's needed, after the
skb replacement (may have) happened.
Cc: stable@vger.kernel.org Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Mon, 2 Jan 2017 03:07:25 +0000 (22:07 -0500)]
Merge branch 'l2tp-socket-lookup-fixes'
Guillaume Nault says:
====================
l2tp: socket lookup fixes for l2tp_ip and l2tp_ip6
There are still some cases that aren't correctly handled in the socket
lookup functions of l2tp_ip and l2tp_ip6. This series fixes lookups for
connected sockets and for sockets bound to the IPv6 unspecified
address.
bind() and connect() should now work as expected on IPPROTO_L2TP
sockets. Extra features, like SO_REUSEADDR, remain unsupported.
The matching conditions in __l2tp_ip6_bind_lookup() and
__l2tp_ip_bind_lookup() are getting hard to read. I've kept the single
test approach to make the intend of the patches clear. I'll split the
conditionals once these fixes reach net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 30 Dec 2016 18:48:20 +0000 (19:48 +0100)]
l2tp: take remote address into account in l2tp_ip and l2tp_ip6 socket lookups
For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the
remote IP when looking for a matching socket. Otherwise a connected
socket can receive traffic not originating from its peer.
Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of
updating their prototype, as these functions aren't used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 30 Dec 2016 18:48:19 +0000 (19:48 +0100)]
l2tp: consider '::' as wildcard address in l2tp_ip6 socket lookup
An L2TP socket bound to the unspecified address should match with any
address. If not, it can't receive any packet and __l2tp_ip6_bind_lookup()
can't prevent another socket from binding on the same device/tunnel ID.
While there, rename the 'addr' variable to 'sk_laddr' (local addr), to
make following patch clearer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Reiter Wolfgang [Sat, 31 Dec 2016 20:11:57 +0000 (21:11 +0100)]
drop_monitor: add missing call to genlmsg_end
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biggers [Fri, 30 Dec 2016 23:42:32 +0000 (17:42 -0600)]
net: socket: don't set sk_uid to garbage value in ->setattr()
->setattr() was recently implemented for socket files to sync the socket
inode's uid to the new 'sk_uid' member of struct sock. It does this by
copying over the ia_uid member of struct iattr. However, ia_uid is
actually only valid when ATTR_UID is set in ia_valid, indicating that
the uid is being changed, e.g. by chown. Other metadata operations such
as chmod or utimes leave ia_uid uninitialized. Therefore, sk_uid could
be set to a "garbage" value from the stack.
Fix this by only copying the uid over when ATTR_UID is set.
Fixes: 86741ec25462 ("net: core: Add a UID field to struct sock.") Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Lorenzo Colitti <lorenzo@google.com> Acked-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 29 Dec 2016 23:29:03 +0000 (15:29 -0800)]
net: ipv4: dst for local input routes should use l3mdev if relevant
IPv4 output routes already use l3mdev device instead of loopback for dst's
if it is applicable. Change local input routes to do the same.
This fixes icmp responses for unreachable UDP ports which are directed
to the wrong table after commit 9d1a6c4ea43e4 because local_input
routes use the loopback device. Moving from ingress device to loopback
loses the L3 domain causing responses based on the dst to get to lost.
Fixes: 9d1a6c4ea43e4 ("net: icmp_route_lookup should use rt dev to
determine L3 domain") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov [Thu, 29 Dec 2016 21:07:38 +0000 (00:07 +0300)]
sh_eth: fix branch prediction in sh_eth_interrupt()
IIUC, likely()/unlikely() should apply to the whole *if* statement's
expression, not a part of it -- fix such expression in sh_eth_interrupt()
accordingly...
Fixes: 283e38db65e7 ("sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers") Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 29 Dec 2016 16:37:13 +0000 (18:37 +0200)]
net/mlx4_core: Fix raw qp flow steering rules under SRIOV
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes: 48564135cba8 ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Slava Shwartsman [Thu, 29 Dec 2016 16:37:12 +0000 (18:37 +0200)]
net/mlx4_en: Fix type mismatch for 32-bit systems
is_power_of_2 expects unsigned long and we pass u64 max_val_cycles,
this will be truncated on 32 bit systems, and the result is not what we
were expecting.
div_u64 expects u32 as a second argument and we pass
max_val_cycles_rounded which is u64 hence it will always be truncated.
Fix was tested on both 64 and 32 bit systems and got same results for
max_val_cycles and max_val_cycles_rounded.
Fixes: 4850cf458157 ("net/mlx4_en: Resolve dividing by zero in 32-bit system") Signed-off-by: Slava Shwartsman <slavash@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Leon Romanovsky [Thu, 29 Dec 2016 16:37:11 +0000 (18:37 +0200)]
net/mlx4: Remove BUG_ON from ICM allocation routine
This patch removes BUG_ON() macro from mlx4_alloc_icm_coherent()
by checking DMA address alignment in advance and performing proper
folding in case of error.
Fixes: 5b0bf5e25efe ("mlx4_core: Support ICM tables in coherent memory") Reported-by: Ozgur Karatas <okaratas@member.fsf.org> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Single send WQE in RX buffer should be stamped with software
ownership in order to prevent the flow of QP in error in FW
once UPDATE_QP is called.
Fixes: 9f519f68cfff ('mlx4_en: Not using Shared Receive Queues') Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Thu, 29 Dec 2016 16:37:09 +0000 (18:37 +0200)]
net/mlx4_core: Use-after-free causes a resource leak in flow-steering detach
mlx4_QP_FLOW_STEERING_DETACH_wrapper first removes the steering
rule (which results in freeing the rule structure), and then
references a field in this struct (the qp number) when releasing the
busy-status on the rule's qp.
Since this memory was freed, it could reallocated and changed.
Therefore, the qp number in the struct may be incorrect,
so that we are releasing the incorrect qp. This leaves the rule's qp
in the busy state (and could possibly release an incorrect qp as well).
Fix this by saving the qp number in a local variable, for use after
removing the steering rule.
Fixes: 2c473ae7e582 ("net/mlx4_core: Disallow releasing VF QPs which have steering rules") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Zhang [Thu, 29 Dec 2016 08:45:04 +0000 (16:45 +0800)]
net: fix incorrect original ingress device index in PKTINFO
When we send a packet for our own local address on a non-loopback
interface (e.g. eth0), due to the change had been introduced from
commit 0b922b7a829c ("net: original ingress device index in PKTINFO"), the
original ingress device index would be set as the loopback interface.
However, the packet should be considered as if it is being arrived via the
sending interface (eth0), otherwise it would break the expectation of the
userspace application (e.g. the DHCPRELEASE message from dhcp_release
binary would be ignored by the dnsmasq daemon, since it come from lo which
is not the interface dnsmasq bind to)
Fixes: 0b922b7a829c ("net: original ingress device index in PKTINFO") Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: Wei Zhang <asuka.com@163.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We miss to check if the netlink message is actually big enough to contain
a struct if_stats_msg.
Add a check to prevent userland from sending us short messages that would
make us access memory beyond the end of the message.
Fixes: 10c9ead9f3c6 ("rtnetlink: add new RTM_GETSTATS message to dump...") Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Dec 2016 23:44:41 +0000 (15:44 -0800)]
net: stmmac: Fix error path after register_netdev move
Commit 5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and
stmmac_open") re-ordered how the MDIO bus registration and the network
device are registered, but missed to unwind the MDIO bus registration in
case we fail to register the network device.
Fixes: 5701659004d6 ("net: stmmac: Fix race between stmmac_drv_probe and stmmac_open") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Zheng Li [Wed, 28 Dec 2016 15:23:46 +0000 (23:23 +0800)]
ipv6: Should use consistent conditional judgement for ip6 fragment between __ip6_append_data and ip6_finish_output
There is an inconsistent conditional judgement between __ip6_append_data
and ip6_finish_output functions, the variable length in __ip6_append_data
just include the length of application's payload and udp6 header, don't
include the length of ipv6 header, but in ip6_finish_output use
(skb->len > ip6_skb_dst_mtu(skb)) as judgement, and skb->len include the
length of ipv6 header.
That causes some particular application's udp6 payloads whose length are
between (MTU - IPv6 Header) and MTU were fragmented by ip6_fragment even
though the rst->dev support UFO feature.
Add the length of ipv6 header to length in __ip6_append_data to keep
consistent conditional judgement as ip6_finish_output for ip6 fragment.
Signed-off-by: Zheng Li <james.z.li@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: atm: Fix warnings in net/atm/lec.c when !CONFIG_PROC_FS
This patch fixes the following warnings when CONFIG_PROC_FS is not set:
linux/net/atm/lec.c: In function ‘lane_module_cleanup’:
linux/net/atm/lec.c:1062:27: error: ‘atm_proc_root’ undeclared (first
use in this function)
remove_proc_entry("lec", atm_proc_root);
^
linux/net/atm/lec.c:1062:27: note: each undeclared identifier is
reported only once for each function it appears in
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
for -stable:
net/mlx5: Check FW limitations on log_max_qp before setting it
net/mlx5: Cancel recovery work in remove flow
net/mlx5: Avoid shadowing numa_node
net/mlx5: Mask destination mac value in ethtool steering rules
net/mlx5: Prevent setting multicast macs for VFs
net/mlx5e: Don't sync netdev state when not registered
net/mlx5e: Disable netdev after close
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:42 +0000 (14:58 +0200)]
net/mlx5e: Disable netdev after close
Disable netdev should come after it was closed, although no harm of doing it
before -hence the MLX5E_STATE_DESTROYING bit- but it is more natural this way.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed [Wed, 28 Dec 2016 12:58:41 +0000 (14:58 +0200)]
net/mlx5e: Don't sync netdev state when not registered
Skip setting netdev vxlan ports and netdev rx_mode on driver load
when netdev is not yet registered.
Synchronizing with netdev state is needed only on reset flow where the
netdev remains registered for the whole reset period.
This also fixes an access before initialization of net_device.addr_list_lock
- which for some reason initialized on register_netdev - where we queued
set_rx_mode work on driver load before netdev registration.
Fixes: 26e59d8077a3 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com> Reviewed-by: Mohamad Haj Yahia <mohamad@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Wed, 28 Dec 2016 12:58:40 +0000 (14:58 +0200)]
net/mlx5e: Check ets capability before initializing ets settings
During the initial setup, the ets command is sent to firmware
without checking if the HCA supports ets. This causes the invalid
command error. Add the ets capiblity check before sending firmware
command to initialize ets settings.
Fixes: e207b7e99176 ("net/mlx5e: ConnectX-4 firmware support for DCBX") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Wed, 28 Dec 2016 12:58:38 +0000 (14:58 +0200)]
Revert "net/mlx5e: Expose PCIe statistics to ethtool"
This reverts commit 9c7262399ba12825f3ca4b00a76d8d5e77c720f5.
PCIe counters were introduced in a new firmware version, as a result users
with old firmware encountered a syndrome every 200ms due to update stats
work. This feature will be re-introduced later with appropriate capabilities
infrastructure.
Fixes: 9c7262399ba1 ("net/mlx5e: Expose PCIe statistics to ethtool") Signed-off-by: Gal Pressman <galp@mellanox.com> Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:36 +0000 (14:58 +0200)]
net/mlx5: Release FTE lock in error flow
Release the FTE lock when adding rule to the FTE has failed.
Fixes: 0fd758d6112f ('net/mlx5: Don't unlock fte while still using it') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maor Gottlieb [Wed, 28 Dec 2016 12:58:35 +0000 (14:58 +0200)]
net/mlx5: Mask destination mac value in ethtool steering rules
We need to mask the destination mac value with the destination mac
mask when adding steering rule via ethtool.
Fixes: 1174fce8d1410 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Wed, 28 Dec 2016 12:58:34 +0000 (14:58 +0200)]
net/mlx5: Avoid shadowing numa_node
Avoid using a local variable named numa_node to avoid shadowing a public
one.
Fixes: db058a186f98 ('net/mlx5_core: Set irq affinity hints') Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Jurgens [Wed, 28 Dec 2016 12:58:33 +0000 (14:58 +0200)]
net/mlx5: Cancel recovery work in remove flow
If there is pending delayed work for health recovery it must be canceled
if the device is being unloaded.
Fixes: 05ac2c0b7438 ("net/mlx5: Fix race between PCI error handlers and health work") Signed-off-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Noa Osherovich [Wed, 28 Dec 2016 12:58:32 +0000 (14:58 +0200)]
net/mlx5: Check FW limitations on log_max_qp before setting it
When setting HCA capabilities, set log_max_qp to be the minimum
between the selected profile's value and the HCA limitation.
Fixes: 938fe83c8dcb ('net/mlx5_core: New device capabilities...') Signed-off-by: Noa Osherovich <noaos@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 28 Dec 2016 12:58:31 +0000 (14:58 +0200)]
net/mlx5: Disable RoCE on the e-switch management port under switchdev mode
Under the switchdev/offloads mode, packets that don't match any
e-switch steering rule are sent towards the e-switch management
port. We use a NIC HW steering rule set per vport (uplink and VFs)
to make them be received into the host OS through the respective
vport representor netdevice.
Currnetly such missed RoCE packets will not get to this NIC steering
rule, and hence VF RoCE will not work over the slow path of the offloads
mode. This is b/c these packets will be matched by a steering rule added
by the firmware that serves RoCE traffic set on the PF NIC vport which
is also the e-switch management port under SRIOV.
Disabling RoCE on the e-switch management vport when we are in the offloads
mode, will signal to the firmware to remove their RoCE rule, and then the
missed RoCE packets will be matched by the representor NIC steering rule
as any other missed packets.
To achieve that, we disable RoCE on the PF vport. We do that by removing
(hot-unplugging) the IB device instance associated with the PF. This is
also required by our current model where the PF serves as the uplink
representor and hence only SW switching (TC, bridge, OVS) applications
and slow path vport mlx5e net-device should be running over that vport.
Fixes: c930a3ad7453 ('net/mlx5e: Add devlink based SRIOV mode changes') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey [Wed, 28 Dec 2016 12:54:47 +0000 (14:54 +0200)]
net/sched: cls_flower: Fix missing addr_type in classify
Since we now use a non zero mask on addr_type, we are matching on its
value (IPV4/IPV6). So before this fix, matching on enc_src_ip/enc_dst_ip
failed in SW/classify path since its value was zero.
This patch sets the proper value of addr_type for encapsulated packets.
Fixes: 970bfcd09791 ('net/sched: cls_flower: Use mask for addr_type') Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Dec 2016 02:23:06 +0000 (18:23 -0800)]
net: stmmac: Fix race between stmmac_drv_probe and stmmac_open
There is currently a small window during which the network device registered by
stmmac can be made visible, yet all resources, including and clock and MDIO bus
have not had a chance to be set up, this can lead to the following error to
occur:
[ 473.919358] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
stmmac_dvr_probe: warning: cannot get CSR clock
[ 473.919382] stmmaceth 0000:01:00.0: no reset control found
[ 473.919412] stmmac - user ID: 0x10, Synopsys ID: 0x42
[ 473.919429] stmmaceth 0000:01:00.0: DMA HW capability register supported
[ 473.919436] stmmaceth 0000:01:00.0: RX Checksum Offload Engine supported
[ 473.919443] stmmaceth 0000:01:00.0: TX Checksum insertion supported
[ 473.919451] stmmaceth 0000:01:00.0 (unnamed net_device) (uninitialized):
Enable RX Mitigation via HW Watchdog Timer
[ 473.921395] libphy: PHY stmmac-1:00 not found
[ 473.921417] stmmaceth 0000:01:00.0 eth0: Could not attach to PHY
[ 473.921427] stmmaceth 0000:01:00.0 eth0: stmmac_open: Cannot attach to
PHY (error: -19)
[ 473.959710] libphy: stmmac: probed
[ 473.959724] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 0 IRQ POLL
(stmmac-1:00) active
[ 473.959728] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 1 IRQ POLL
(stmmac-1:01)
[ 473.959731] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 2 IRQ POLL
(stmmac-1:02)
[ 473.959734] stmmaceth 0000:01:00.0 eth0: PHY ID 01410cc2 at 3 IRQ POLL
(stmmac-1:03)
Fix this by making sure that register_netdev() is the last thing being done,
which guarantees that the clock and the MDIO bus are available.
Fixes: 4bfcbd7abce2 ("stmmac: Move the mdio_register/_unregister in probe/remove") Reported-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Acked-By: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 26 Dec 2016 16:31:27 +0000 (08:31 -0800)]
openvswitch: upcall: Fix vlan handling.
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes: 5108bbaddc ("openvswitch: add processing of L3 packets"). CC: Jarno Rajahalme <jarno@ovn.org> CC: Jiri Benc <jbenc@redhat.com> Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 25 Dec 2016 06:33:16 +0000 (14:33 +0800)]
ipv4: Namespaceify tcp_tw_reuse knob
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Sat, 24 Dec 2016 03:56:56 +0000 (19:56 -0800)]
net: korina: Fix NAPI versus resources freeing
Commit beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb77e ("korina: disable napi on close and restart") Reported-by: Alexandros C. Couloumbis <alex@ozo.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 21 Dec 2016 17:04:11 +0000 (18:04 +0100)]
net, sched: fix soft lockup in tc_classify
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes: 12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup") Reported-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Eric Dumazet <edumazet@google.com> Tested-by: Shahar Klein <shahark@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger [Fri, 23 Dec 2016 03:06:53 +0000 (21:06 -0600)]
powerpc: Fix build warning on 32-bit PPC
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit 989cea5c14be ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit 9994a33865f4 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes: 9994a33865f4 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 Dec 2016 22:56:58 +0000 (14:56 -0800)]
avoid spurious "may be used uninitialized" warning
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Linus Torvalds [Sun, 25 Dec 2016 22:30:04 +0000 (14:30 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Linus Torvalds [Sun, 25 Dec 2016 22:05:56 +0000 (14:05 -0800)]
Merge branch 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
Linus Torvalds [Sun, 25 Dec 2016 22:01:28 +0000 (14:01 -0800)]
Merge branch 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
Nicholas Piggin [Sun, 25 Dec 2016 03:00:30 +0000 (13:00 +1000)]
mm: add PageWaiters indicating tasks are waiting for a page bit
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sun, 25 Dec 2016 11:30:41 +0000 (12:30 +0100)]
ktime: Cleanup ktime_set() usage
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
Thomas Gleixner [Sun, 25 Dec 2016 10:38:40 +0000 (11:38 +0100)]
ktime: Get rid of the union
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org>
Thomas Gleixner [Wed, 21 Dec 2016 19:19:57 +0000 (20:19 +0100)]
irqchip/armada-xp: Consolidate hotplug state space
The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Wed, 21 Dec 2016 19:19:56 +0000 (20:19 +0100)]
irqchip/gic: Consolidate hotplug state space
Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.
So having seperate hotplug states for them is pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Wed, 21 Dec 2016 19:19:54 +0000 (20:19 +0100)]
cpu/hotplug: Cleanup state names
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove also the now pointless cpu notifier error injection mechanism. The
states can be executed step by step and error rollback is the same as cpu
down, so any state transition can be tested w/o requiring the notifier
error injection.
Some CPU hotplug states are kept as they are (ab)used for hotplug state
tracking.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: rt@linutronix.de Link: http://lkml.kernel.org/r/20161221192112.005642358@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Wed, 21 Dec 2016 19:19:49 +0000 (20:19 +0100)]
cpu/hotplug: Prevent overwriting of callbacks
Developers manage to overwrite states blindly without thought. That's fatal
and hard to debug. Add sanity checks to make it fail.
This requries to restructure the code so that the dynamic state allocation
happens in the same lock protected section as the actual store. Otherwise
the previous assignment of 'Reserved' to the name field would trigger the
overwrite check.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Link: http://lkml.kernel.org/r/20161221192111.675234535@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Thu, 22 Dec 2016 09:32:38 +0000 (10:32 +0100)]
x86/msr: Remove bogus cleanup from the error path
The error cleanup which is invoked when the hotplug state setup failed
tries to remove the failed state, which is broken.
Fixes: 8fba38c937cd ("x86/msr: Convert to hotplug state machine") Reported-by: kernel test robot <fengguang.wu@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Sebastian Siewior <bigeasy@linutronix.de>
Thomas Gleixner [Thu, 22 Dec 2016 10:14:06 +0000 (11:14 +0100)]
bus: arm-ccn: Prevent hotplug callback leak
In case the driver registration fails, the hotplug callback is leaked.
Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.
Fixes: fdc15a36d84e ("bus/arm-ccn: Convert to hotplug statemachine") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Will Deacon <will.deacon@arm.com>
If the pmu registration fails the registered hotplug callbacks are not
removed. Wrong in any case, but fatal in case of a modular driver.
Replace the nonsensical state names with proper ones while at it.
Fixes: 77c34ef1c319 ("perf/x86/intel/cstate: Convert Intel CSTATE to hotplug state machine") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org
Thomas Gleixner [Wed, 21 Dec 2016 19:19:48 +0000 (20:19 +0100)]
ARM/imx/mmcd: Fix broken cpu hotplug handling
The cpu hotplug support of this perf driver is broken in several ways:
1) It adds a instance before setting up the state.
2) The state for the instance is different from the state of the
callback. It's just a randomly chosen state.
3) The instance registration is not error checked so nobody noticed that
the call can never succeed.
4) The state for the multi install callbacks is chosen randomly and
overwrites existing state. This is now prevented by the core code so the
call is guaranteed to fail.
5) The error exit path in the init function leaves the instance registered
and then frees the memory which contains the enqueued hlist node.
6) The remove function is removing the state and not the instance.
Fix it by:
- Setting up the state before adding instances. Use a dynamically allocated
state for it.
- Installing instances after the state has been set up
- Removing the instance in the error path before freeing memory
- Removing the instance not the state in the driver remove callback
While at is use raw_cpu_processor_id(), because cpu_processor_id() cannot
be used in preemptible context, and set the driver data after successful
registration of the pmu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Shawn Guo <shawnguo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Frank Li <frank.li@nxp.com> Cc: Zhengyu Shen <zhengyu.shen@nxp.com> Link: http://lkml.kernel.org/r/20161221192111.596204211@linutronix.de Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Sat, 24 Dec 2016 11:34:02 +0000 (12:34 +0100)]
scsi: qedi: Convert to hotplug state machine
The CPU hotplug code is a trainwreck. It leaks a notifier in case of driver
registration error and the per cpu loop is racy against cpu hotplug. Aside
of that the driver should have been written and merged with the new state
machine interfaces in the first place.
Mop up the mess and Convert it to the hotplug state machine.
Signed-off-by: Thomas Grumpy Gleixner <tglx@linutronix.de> Cc: Nilesh Javali <nilesh.javali@cavium.com> Cc: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com> Cc: Chad Dupuis <chad.dupuis@cavium.com> Cc: Saurav Kashyap <saurav.kashyap@cavium.com> Cc: Arun Easi <arun.easi@cavium.com> Cc: Manish Rangankar <manish.rangankar@cavium.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Hannes Reinecke <hare@suse.de> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Linus Torvalds [Sat, 24 Dec 2016 19:37:18 +0000 (11:37 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"This ncludes various cifs/smb3 bug fixes, mostly for stable as well.
In the next week I expect that Germano will have some reconnection
fixes, and also I expect to have the remaining pieces of the snapshot
enablement and SMB3 ACLs, but wanted to get this set of bug fixes in"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs_get_root shouldn't use path with tree name
Fix default behaviour for empty domains and add domainauto option
cifs: use %16phN for formatting md5 sum
cifs: Fix smbencrypt() to stop pointing a scatterlist at the stack
CIFS: Fix a possible double locking of mutex during reconnect
CIFS: Fix a possible memory corruption during reconnect
CIFS: Fix a possible memory corruption in push locks
CIFS: Fix missing nls unload in smb2_reconnect()
CIFS: Decrease verbosity of ioctl call
SMB3: parsing for new snapshot timestamp mount parm
Linus Torvalds [Sat, 24 Dec 2016 19:27:45 +0000 (11:27 -0800)]
Merge tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull watchdog updates from Wim Van Sebroeck and Guenter Roeck:
- new driver for Add Loongson1 SoC
- minor cleanup and fixes in various drivers
* tag 'watchdog-for-linus-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
watchdog: it87_wdt: add IT8620E ID
watchdog: mpc8xxx: Remove unneeded linux/miscdevice.h include
watchdog: octeon: Remove unneeded linux/miscdevice.h include
watchdog: bcm2835_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: loongson1: Add Loongson1 SoC watchdog driver
watchdog: cpwd: remove memory allocate failure message
watchdog: da9062/61: watchdog driver
intel-mid_wdt: Error code is just an integer
intel-mid_wdt: make sure watchdog is not running at startup
watchdog: mei_wdt: request stop on reboot to prevent false positive event
watchdog: hpwdt: changed maintainer information
watchdog: jz4740: Fix modular build
watchdog: qcom: fix kernel panic due to external abort on non-linefetch
watchdog: davinci: add support for deferred probing
watchdog: meson: Remove unneeded platform MODULE_ALIAS
watchdog: Standardize leading tabs and spaces in Kconfig file
watchdog: max77620_wdt: fix module autoload
watchdog: bcm7038_wdt: fix module autoload
Linus Torvalds [Sat, 24 Dec 2016 19:23:24 +0000 (11:23 -0800)]
Merge tag 'ntb-4.10' of git://github.com/jonmason/ntb
Pull NTB update from Jon Mason:
- NTB bug fixes for removing an unnecessary call to ntb_peer_spad_read,
and correcting a free_irq inconsistency
- add Intel SKX support
- change the AMD NTB maintainer, and fix some bugs present there
* tag 'ntb-4.10' of git://github.com/jonmason/ntb:
ntb_transport: Remove unnecessary call to ntb_peer_spad_read
NTB: Fix 'request_irq()' and 'free_irq()' inconsistancy
ntb: fix SKX NTB config space size register offsets
NTB: correct ntb_peer_spad_read for case when callback is not supplied.
MAINTAINERS: Change in maintainer for AMD NTB
ntb_transport: Limit memory windows based on available, scratchpads
NTB: Register and offset values fix for memory window
NTB: add support for hotplug feature
ntb: Adding Skylake Xeon NTB support
Linus Torvalds [Sat, 24 Dec 2016 00:54:46 +0000 (16:54 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"There's a number of fixes:
- a round of fixes for CPUID-less legacy CPUs
- a number of microcode loader fixes
- i8042 detection robustization fixes
- stack dump/unwinder fixes
- x86 SoC platform driver fixes
- a GCC 7 warning fix
- virtualization related fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
Revert "x86/unwind: Detect bad stack return address"
x86/paravirt: Mark unused patch_default label
x86/microcode/AMD: Reload proper initrd start address
x86/platform/intel/quark: Add printf attribute to imr_self_test_result()
x86/platform/intel-mid: Switch MPU3050 driver to IIO
x86/alternatives: Do not use sync_core() to serialize I$
x86/topology: Document cpu_llc_id
x86/hyperv: Handle unknown NMIs on one CPU when unknown_nmi_panic
x86/asm: Rewrite sync_core() to use IRET-to-self
x86/microcode/intel: Replace sync_core() with native_cpuid()
Revert "x86/boot: Fail the boot if !M486 and CPUID is missing"
x86/asm/32: Make sync_core() handle missing CPUID on all 32-bit kernels
x86/cpu: Probe CPUID leaf 6 even when cpuid_level == 6
x86/tools: Fix gcc-7 warning in relocs.c
x86/unwind: Dump stack data on warnings
x86/unwind: Adjust last frame check for aligned function stacks
x86/init: Fix a couple of comment typos
x86/init: Remove i8042_detect() from platform ops
Input: i8042 - Trust firmware a bit more when probing on X86
x86/init: Add i8042 state to the platform data
...
projects / linux.git / log