samples/bpf: program demonstrating access to xdp_rxq_info
This sample program can be used for monitoring and reporting how many
packets per sec (pps) are received per NIC RX queue index and which
CPU processed the packet. In itself it is a useful tool for quickly
identifying RSS imbalance issues, see below.
The default XDP action is XDP_PASS in-order to provide a monitor
mode. For benchmarking purposes it is possible to specify other XDP
actions on the cmdline --action.
Output below shows an imbalance RSS case where most RXQ's deliver to
CPU-0 while CPU-2 only get packets from a single RXQ. Looking at
things from a CPU level the two CPUs are processing approx the same
amount, BUT looking at the rx_queue_index levels it is clear that
RXQ-2 receive much better service, than other RXQs which all share CPU-0.
Running XDP on dev:i40e1 (ifindex:3) action:XDP_PASS
XDP stats CPU pps issue-pps
XDP-RX CPU 0 900,473 0
XDP-RX CPU 2 906,921 0
XDP-RX CPU total 1,807,395
bpf: finally expose xdp_rxq_info to XDP bpf-programs
Now all XDP driver have been updated to setup xdp_rxq_info and assign
this to xdp_buff->rxq. Thus, it is now safe to enable access to some
of the xdp_rxq_info struct members.
This patch extend xdp_md and expose UAPI to userspace for
ingress_ifindex and rx_queue_index. Access happens via bpf
instruction rewrite, that load data directly from struct xdp_rxq_info.
* ingress_ifindex map to xdp_rxq_info->dev->ifindex
* rx_queue_index map to xdp_rxq_info->queue_index
The net_device have some members (num_rx_queues + real_num_rx_queues)
and data-area (dev->_rx with struct netdev_rx_queue's) that were
primarily used for exporting information about RPS (CONFIG_RPS) queues
to sysfs (CONFIG_SYSFS).
For generic XDP extend struct netdev_rx_queue with the xdp_rxq_info,
and remove some of the CONFIG_SYSFS ifdefs.
The virtio_net driver doesn't dynamically change the RX-ring queue
layout and backing pages, but instead reject XDP setup if all the
conditions for XDP is not meet. Thus, the xdp_rxq_info also remains
fairly static. This allow us to simply add the reg/unreg to
net_device open/close functions.
V3:
- bugfix, also setup xdp.rxq in receive_mergeable()
- Tested bpf-sample prog inside guest on a virtio_net device
Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: virtualization@lists.linux-foundation.org Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
I've done some manual testing of this tun driver, but I would
appriciate good review and someone else running their use-case tests,
as I'm not 100% sure I understand the tfile->detached semantics.
V2: Removed the skb_array_cleanup() call from V1 by request from Jason Wang.
Cc: Jason Wang <jasowang@redhat.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Reviewed-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This driver uses a bool scheme for "enable"/"disable" when setting up
different resources. Thus, the hook points for xdp_rxq_info is done
in the same function call nicvf_rcv_queue_config(). This is activated
through enable/disable via nicvf_config_data_transfer(), which is tied
into nicvf_stop()/nicvf_open().
Extending driver packet handler call-path nicvf_rcv_pkt_handler() with
a pointer to the given struct rcv_queue, in-order to access the
xdp_rxq_info data area (in nicvf_xdp_rx()).
V2: Driver have no proper error path for failed XDP RX-queue info reg,
as nicvf_rcv_queue_config is a void function.
xdp/qede: setup xdp_rxq_info and intro xdp_rxq_info_is_reg
The driver code qede_free_fp_array() depend on kfree() can be called
with a NULL pointer. This stems from the qede_alloc_fp_array()
function which either (kz)alloc memory for fp->txq or fp->rxq.
This also simplifies error handling code in case of memory allocation
failures, but xdp_rxq_info_unreg need to know the difference.
Introduce xdp_rxq_info_is_reg() to handle if a memory allocation fails
and detect this is the failure path by seeing that xdp_rxq_info was
not registred yet, which first happens after successful alloaction in
qede_init_fp().
The i40e driver has a special "FDIR" RX-ring (I40E_VSI_FDIR) which is
a sideband channel for configuring/updating the flow director tables.
This (i40e_vsi_)type does not invoke XDP-ebpf code.
As suggested by Björn (V2): Instead of marking this I40E_VSI_FDIR RX-ring
a special case, reverse the logic and only select RX-rings of type
I40E_VSI_MAIN to register xdp_rxq_info's for.
The mlx5 driver have a special drop-RQ queue (one per interface) that
simply drops all incoming traffic. It helps driver keep other HW
objects (flow steering) alive upon down/up operations. It is
temporarily pointed by flow steering objects during the interface
setup, and when interface is down. It lacks many fields that are set
in a regular RQ (for example its state is never switched to
MLX5_RQC_STATE_RDY). (Thanks to Tariq Toukan for explanation).
The XDP RX-queue info for this drop-RQ marked as unused, which
allow us to use the same takedown/free code path as other RX-queues.
This patch only introduce the core data structures and API functions.
All XDP enabled drivers must use the API before this info can used.
There is a need for XDP to know more about the RX-queue a given XDP
frames have arrived on. For both the XDP bpf-prog and kernel side.
Instead of extending xdp_buff each time new info is needed, the patch
creates a separate read-mostly struct xdp_rxq_info, that contains this
info. We stress this data/cache-line is for read-only info. This is
NOT for dynamic per packet info, use the data_meta for such use-cases.
The performance advantage is this info can be setup at RX-ring init
time, instead of updating N-members in xdp_buff. A possible (driver
level) micro optimization is that xdp_buff->rxq assignment could be
done once per XDP/NAPI loop. The extra pointer deref only happens for
program needing access to this info (thus, no slowdown to existing
use-cases).
Daniel Borkmann [Thu, 4 Jan 2018 11:28:47 +0000 (12:28 +0100)]
Merge branch 'bpf-bpftool-misc-fixes'
Jakub Kicinski says:
====================
This series addresses small issues that snuck through the review
of cgroup code. "list" and "show" are now made aliases to satisfy
all users. Small fix to errors printed is needed, errors can't
contain new line characters, otherwise JSON will break.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Tue, 2 Jan 2018 22:48:37 +0000 (14:48 -0800)]
tools: bpftool: remove new lines from errors
It's a little bit unusual for kernel style, but we add the new line
character to error strings inside the p_err() function. We do this
because new lines at the end of error strings will break JSON output.
Fix a few p_err("..\n") which snuck in recently.
Fixes: 5ccda64d38cc ("bpftool: implement cgroup bpf operations") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Tue, 2 Jan 2018 22:48:35 +0000 (14:48 -0800)]
tools: bpftool: rename cgroup list -> show in the code
So far we have used "show" as a keyword for listing
programs and maps. Use the word "show" in the code
for cgroups too, next commit will alias show and list.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann [Sun, 31 Dec 2017 15:12:24 +0000 (16:12 +0100)]
Merge branch 'bpf-offload-report-dev'
Jakub Kicinski says:
====================
This series is a redo of reporting offload device information to
user space after the first attempt did not take into account name
spaces. As requested by Kirill offloads are now protected by an
r/w sem. This allows us to remove the workqueue and free the
offload state fully when device is removed (suggested by Alexei).
Net namespace is reported with a device/inode pair.
The accompanying bpftool support is placed in common code because
maps will have very similar info. Note that the UAPI information
can't be nicely encapsulated into a struct, because in case we
need to grow the device information the new fields will have to
be added at the end of struct bpf_prog_info, we can't grow
structures in the middle of bpf_prog_info.
v3:
- use dev_get_by_index();
- redo ns code (new patch 6).
v2:
- rework the locking in patch 1 (use RCU instead of locking
dependencies);
- grab RTNL for a short time in patch 6;
- minor update to the test in patch 8.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:11 +0000 (18:39 -0800)]
selftests/bpf: test device info reporting for bound progs
Check if bound programs report correct device info. Test
in local namespace, in remote one, back to the local ns,
remove the device and check that information is cleared.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:09 +0000 (18:39 -0800)]
bpf: offload: report device information for offloaded programs
Report to the user ifindex and namespace information of offloaded
programs. If device has disappeared return -ENODEV. Specify the
namespace using dev/inode combination.
CC: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:08 +0000 (18:39 -0800)]
nsfs: generalize ns_get_path() for path resolution with a task
ns_get_path() takes struct task_struct and proc_ns_ops as its
parameters. For path resolution directly from a namespace,
e.g. based on a networking device's net name space, we need
more flexibility. Add a ns_get_path_cb() helper which will
allow callers to use any method of obtaining the name space
reference. Convert ns_get_path() to use ns_get_path_cb().
Following patches will bring a networking user.
CC: Eric W. Biederman <ebiederm@xmission.com> Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:07 +0000 (18:39 -0800)]
bpf: offload: free program id when device disappears
Bound programs are quite useless after their device disappears.
They are simply waiting for reference count to go to zero,
don't list them in BPF_PROG_GET_NEXT_ID by freeing their ID
early.
Note that orphaned offload programs will return -ENODEV on
BPF_OBJ_GET_INFO_BY_FD so user will never see ID 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:05 +0000 (18:39 -0800)]
bpf: offload: allow netdev to disappear while verifier is running
To allow verifier instruction callbacks without any extra locking
NETDEV_UNREGISTER notification would wait on a waitqueue for verifier
to finish. This design decision was made when rtnl lock was providing
all the locking. Use the read/write lock instead and remove the
workqueue.
Verifier will now call into the offload code, so dev_ops are moved
to offload structure. Since verifier calls are all under
bpf_prog_is_dev_bound() we no longer need static inline implementations
to please builds with CONFIG_NET=n.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:04 +0000 (18:39 -0800)]
bpf: offload: don't use prog->aux->offload as boolean
We currently use aux->offload to indicate that program is bound
to a specific device. This forces us to keep the offload structure
around even after the device is gone. Add a bool member to
struct bpf_prog_aux to indicate if offload was requested.
Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jakub Kicinski [Thu, 28 Dec 2017 02:39:03 +0000 (18:39 -0800)]
bpf: offload: don't require rtnl for dev list manipulation
We don't need the RTNL lock for all operations on offload state.
We only need to hold it around ndo calls. The device offload
initialization doesn't require it. The soon-to-come querying
of the offload info will only need it partially. We will also
be able to remove the waitqueue in following patches.
Use struct rw_semaphore because map offload will require sleeping
with the semaphore held for read.
Suggested-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Roman Gushchin [Wed, 27 Dec 2017 19:16:29 +0000 (19:16 +0000)]
tools/bpftool: fix bpftool build with bintutils >= 2.9
Bpftool build is broken with binutils version 2.29 and later.
The cause is commit 003ca0fd2286 ("Refactor disassembler selection")
in the binutils repo, which changed the disassembler() function
signature.
Fix this by adding a new "feature" to the tools/build/features
infrastructure and make it responsible for decision which
disassembler() function signature to use.
Signed-off-by: Roman Gushchin <guro@fb.com> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Roman Gushchin [Wed, 27 Dec 2017 19:16:28 +0000 (19:16 +0000)]
tools/bpftool: use version from the kernel source tree
Bpftool determines it's own version based on the kernel
version, which is picked from the linux/version.h header.
It's strange to use the version of the installed kernel
headers, and makes much more sense to use the version
of the actual source tree, where bpftool sources are.
Fix this by building kernelversion target and use
the resulting string as bpftool version.
Example:
before:
$ bpftool version
bpftool v4.14.6
after:
$ bpftool version
bpftool v4.15.0-rc3
$bpftool version --json
{"version":"4.15.0-rc3"}
Signed-off-by: Roman Gushchin <guro@fb.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
1) IPv6 gre tunnels end up with different default features enabled
depending upon whether netlink or ioctls are used to bring them up.
Fix from Alexey Kodanev.
2) Fix read past end of user control message in RDS< from Avinash
Repaka.
3) Missing RCU barrier in mini qdisc code, from Cong Wang.
4) Missing policy put when reusing per-cpu route entries, from Florian
Westphal.
5) Handle nested PCI errors properly in bnx2x driver, from Guilherme G.
Piccoli.
6) Run nested transport mode IPSEC packets via tasklet, from Herbert
Xu.
7) Fix handling poll() for stream sockets in tipc, from Parthasarathy
Bhuvaragan.
8) Fix two stack-out-of-bounds issues in IPSEC, from Steffen Klassert.
9) Another zerocopy ubuf handling fix, from Willem de Bruijn.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
strparser: Call sock_owned_by_user_nocheck
sock: Add sock_owned_by_user_nocheck
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
tipc: fix hanging poll() for stream sockets
sctp: Replace use of sockets_allocated with specified macro.
bnx2x: Improve reliability in case of nested PCI errors
tg3: Enable PHY reset in MTU change path for 5720
tg3: Add workaround to restrict 5762 MRRS to 2048
tg3: Update copyright
net: fec: unmap the xmit buffer that are not transferred by DMA
tipc: fix tipc_mon_delete() oops in tipc_enable_bearer() error path
tipc: error path leak fixes in tipc_enable_bearer()
RDS: Check cmsg_len before dereferencing CMSG_DATA
tcp: Avoid preprocessor directives in tracepoint macro args
tipc: fix memory leak of group member when peer node is lost
net: sched: fix possible null pointer deref in tcf_block_put
tipc: base group replicast ack counter on number of actual receivers
net_sched: fix a missing rcu barrier in mini_qdisc_pair_swap()
net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaround
ip6_gre: fix device features for ioctl setup
...
Linus Torvalds [Fri, 29 Dec 2017 07:16:24 +0000 (23:16 -0800)]
Merge tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"nouveau and i915 regression fixes"
* tag 'drm-fixes-for-v4.15-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: fix race when adding delayed work items
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
Linus Torvalds [Fri, 29 Dec 2017 07:14:47 +0000 (23:14 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One more fix for the runtime PM clk patches. We're calling a runtime
PM API that may schedule from somewhere that we can't do that. We
change to the async version of pm_runtime_put() to fix it"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: use atomic runtime pm api in clk_core_is_enabled
Linus Torvalds [Fri, 29 Dec 2017 07:09:45 +0000 (23:09 -0800)]
Merge tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fix from Jacek Anaszewski:
"A single LED fix for brightness setting when delay_off is 0"
* tag 'led_fixes_for_4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
led: core: Fix brightness setting when setting delay_off=0
Linus Torvalds [Fri, 29 Dec 2017 07:06:01 +0000 (23:06 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"This is the next batch of for-rc patches from RDMA. It includes the
fix for the ipoib regression I mentioned last time, and the result of
a fairly major debugging effort to get iser working reliably on cxgb4
hardware - it turns out the cxgb4 driver was not handling QP error
flushing properly causing iser to fail.
- cxgb4 fix for an iser testing failure as debugged by Steve and
Sagi. The problem was a driver bug in the handling of shutting down
a QP.
- Various vmw_pvrdma fixes for bogus WARN_ON, missed resource free on
error unwind and a use after free bug
- Improper congestion counter values on mlx5 when link aggregation is
enabled
- ipoib lockdep regression introduced in this merge window
- hfi1 regression supporting the device in a VM introduced in a
recent patch
- Typo that breaks future uAPI compatibility in the verbs core
- More SELinux related oops fixing
- Fix an oops during error unwind in mlx5"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
IB/core: Verify that QP is security enabled in create and destroy
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
IB/mlx5: Serialize access to the VMA list
IB/hfi: Only read capability registers if the capability exists
IB/ipoib: Fix lockdep issue found on ipoib_ib_dev_heavy_flush
IB/mlx5: Fix congestion counters in LAG mode
RDMA/vmw_pvrdma: Avoid use after free due to QP/CQ/SRQ destroy
RDMA/vmw_pvrdma: Use refcount_dec_and_test to avoid warning
RDMA/vmw_pvrdma: Call ib_umem_release on destroy QP path
iw_cxgb4: when flushing, complete all wrs in a chain
iw_cxgb4: reflect the original WR opcode in drain cqes
iw_cxgb4: Only validate the MSN for successful completions
This series includes updates for mlx5 E-Switch infrastructures,
to be merged into net-next and rdma-next trees.
Mark's patches provide E-Switch refactoring that generalize the mlx5
E-Switch vf representors interfaces and data structures. The serious is
mainly focused on moving ethernet (netdev) specific representors logic out
of E-Switch (eswitch.c) into mlx5e representor module (en_rep.c), which
provides better separation and allows future support for other types of vf
representors (e.g. RDMA).
Gal's patches at the end of this serious, provide a simple syntax fix and
two other patches that handles vport ingress/egress ACL steering name
spaces to be aligned with the Firmware/Hardware specs.
V1->V2:
- Addressed coding style comments in patches #1 and #7
- The series is still based on rc4, as now I see net-next is also @rc4.
V2->V3:
- Fixed compilation warning, reported by Dave.
Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Tue, 28 Nov 2017 09:58:51 +0000 (11:58 +0200)]
net/mlx5: Separate ingress/egress namespaces for each vport
Each vport has its own root flow table for the ACL flow tables and root
flow table is per namespace, therefore we should create a namespace for
each vport.
Mark Bloch [Thu, 7 Dec 2017 21:25:57 +0000 (21:25 +0000)]
net/mlx5: E-Switch, Create generic header struct to be used by representors
Now that we don't store type dependent data in struct mlx5_eswitch_rep
we can create a generic interface, and representor type.
struct mlx5_eswitch_rep will store an array of interfaces, each
interface is used by a different representor type.
Once we moved to a more generic interface, rdma driver representors can
be added and utilize the same mechanism as the Ethernet driver
representors use.
Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Thu, 28 Dec 2017 19:28:23 +0000 (14:28 -0500)]
Merge branch 'strparser-Fix-lockdep-issue'
Tom Herbert says:
====================
strparser: Fix lockdep issue
When sock_owned_by_user returns true in strparser. Fix is to add and
call sock_owned_by_user_nocheck since the check for owned by user is
not an error condition in this case.
====================
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Thu, 28 Dec 2017 19:00:44 +0000 (11:00 -0800)]
strparser: Call sock_owned_by_user_nocheck
strparser wants to check socket ownership without producing any
warnings. As indicated by the comment in the code, it is permissible
for owned_by_user to return true.
Fixes: 43a0c6751a322847 ("strparser: Stream parser for messages") Reported-by: syzbot <syzkaller@googlegroups.com> Reported-and-tested-by: <syzbot+c91c53af67f9ebe599a337d2e70950366153b295@syzkaller.appspotmail.com> Signed-off-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Thu, 28 Dec 2017 17:38:13 +0000 (12:38 -0500)]
skbuff: in skb_copy_ubufs unclone before releasing zerocopy
skb_copy_ubufs must unclone before it is safe to modify its
skb_shared_info with skb_zcopy_clear.
Commit b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even
without user frags") ensures that all skbs release their zerocopy
state, even those without frags.
But I forgot an edge case where such an skb arrives that is cloned.
The stack does not build such packets. Vhost/tun skbs have their
frags orphaned before cloning. TCP skbs only attach zerocopy state
when a frag is added.
But if TCP packets can be trimmed or linearized, this might occur.
Tracing the code I found no instance so far (e.g., skb_linearize
ends up calling skb_zcopy_clear if !skb->data_len).
Still, it is non-obvious that no path exists. And it is fragile to
rely on this.
Fixes: b90ddd568792 ("skbuff: skb_copy_ubufs must release uarg even without user frags") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Dec 2017 17:24:06 +0000 (12:24 -0500)]
Merge branch 'mlx4-misc-for-4.16'
Tariq Toukan says:
====================
mlx4 misc for 4.16
This patchset contains misc cleanups and improvements
to the mlx4 Core and Eth drivers.
In patches 1 and 2 I reduce and reorder the branches in the RX csum flow.
In patch 3 I align the FMR unmapping flow with the device spec, to allow
a remapping afterwards.
Patch 4 by Moni changes the default QoS settings so that a pause
frame stops all traffic regardless of its prio.
Series generated against net-next commit: 836df24a7062 net: hns3: hns3_get_channels() can be static
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These new settings cause that a pause frame for any prio stops
traffic for all prios.
Fixes: 564c274c3df0 ("net/mlx4_en: DCB QoS support") Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 28 Dec 2017 14:26:10 +0000 (16:26 +0200)]
net/mlx4_core: Cleanup FMR unmapping flow
Remove redundant and not essential operations in fmr unmap/free.
According to device spec, in FMR unmap it is sufficient to set
ownership bit to SW. This allows remapping afterwards.
Fixes: 8ad11fb6b073 ("IB/mlx4: Implement FMRs") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 28 Dec 2017 14:26:08 +0000 (16:26 +0200)]
net/mlx4_en: RX csum, remove redundant branches and checks
Do not check IPv6 bit in cqe status if CONFIG_IPV6 is not enabled.
Function check_csum() is reached only with IPv4 or IPv6 set (if enabled),
if IPv6 is not set (or is not enabled) it is redundant to test the
IPv4 bit.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 28 Dec 2017 15:52:10 +0000 (16:52 +0100)]
net: sched: don't set extack message in case the qdisc will be created
If the qdisc is not found here, it is going to be created. Therefore,
this is not an error path. Remove the extack message set and don't
confuse user with error message in case the qdisc was created
successfully.
Fixes: 09215598119e ("net: sched: sch_api: handle generic qdisc errors") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 42b531de17d2f6 ("tipc: Fix missing connection request
handling"), we replaced unconditional wakeup() with condtional
wakeup for clients with flags POLLIN | POLLRDNORM | POLLRDBAND.
This breaks the applications which do a connect followed by poll
with POLLOUT flag. These applications are not woken when the
connection is ESTABLISHED and hence sleep forever.
In this commit, we fix it by including the POLLOUT event for
sockets in TIPC_CONNECTING state.
Fixes: 42b531de17d2f6 ("tipc: Fix missing connection request handling") Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY patch included in v1 has already separated in:
http://www.spinics.net/lists/netdev/msg454595.html
Changes since v8:
- move operators at the beginning of the line to the end of the previous line
- dt-bindings: add blank lines before mdio and phy subnodes
Changes since v7:
- dt-bindings: fix mdio subnode description
Changes since v6:
- sort the order of local variables from longest to shortest line
- fix ave_probe() which calls register_netdev() at the end of initialization
- dt-bindings: remove phy node descriptions in mdio node
Changes since v5:
- replace license boilerplate with SPDX Identifier
- remove inline directives and an unused function
Changes since v4:
- fix larger integer warning on AVE_PFMBYTE_MASK0
Changes since v3:
- remove checking dma address and use dma_set_mask() to restirct address
- replace ave_mdio_busywait() with read_poll_timeout()
- replace functions to access to registers with readl/writel() directly
- replace a function to access to macaddr with ave_hw_write_macaddr()
- change return value of ave_dma_map() to error value
- move mdiobus_unregister() from ave_remove() to ave_uninit()
- eliminate else block at the end of ave_dma_map()
- add mask definitions for packet filter
- sort bitmap definitions in descending order
- add error check to some functions
- rename and sort functions to clear sub-categories
- fix error value consistency
- remove unneeded initializers
- change type of constant arrays
Changes since v2:
- replace clk_get() with devm_clk_get()
- replace reset_control_get() with devm_reset_control_get_optional_shared()
- add error return when the error occurs on the above *_get functions
- sort soc data and compatible strings
- remove clearly obvious comments
- modify dt-bindings document consistent with these modifications
Changes since v1:
- add/remove devicetree properties and sub-node
- remove "internal-phy-interrupt" and "desc-bits" property
- add SoC data structures based on compatible strings
- add node operation to apply "mdio" sub-node
- add support for features
- add support for {get,set}_pauseparam and pause frame operations
- add support for ndo_get_stats64 instead of ndo_get_stats
- replace with desiable functions
- replace check for valid phy_mode with phy_interface{_mode}_is_rgmii()
- replace phy attach message with phy_attached_info()
- replace 32bit operation with {upper,lower}_32_bits() on ave_wdesc_addr()
- replace nway_reset and get_link with generic functions
- move operations to proper functions
- move phy_start_aneg() to ndo_open,
and remove unnecessary PHY interrupt operations
See http://www.spinics.net/lists/netdev/msg454590.html
- move irq initialization and descriptor memory allocation to ndo_open
- move initialization of reset and clock and mdiobus to ndo_init
- fix skbuffer operations
- fix skb alignment operations and add Rx buffer adjustment for descriptor
See http://www.spinics.net/lists/netdev/msg456014.html
- add error returns when dma_map_single() failed
- clean up code structures
- clean up wait-loop and wake-queue conditions
- add ave_wdesc_addr() and offset definitions
- add ave_macaddr_init() to clean up mac-address operation
- fix checking whether Tx entry is not enough
- fix supported features of phydev
- add necessary free/disable operations
- add phydev check on ave_{get,set}_wol()
- remove netif_carrier functions, phydev initializer, and Tx budget check
- change obsolate codes
- replace ndev->{base_addr,irq} with the members of ave_private
- rename goto labels and mask definitions, and remove unused codes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kunihiko Hayashi [Thu, 28 Dec 2017 06:58:12 +0000 (15:58 +0900)]
net: ethernet: socionext: add AVE ethernet driver
The UniPhier platform from Socionext provides the AVE ethernet
controller that includes MAC and MDIO bus supporting RGMII/RMII
modes. The controller is named AVE.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 28 Dec 2017 06:37:15 +0000 (12:07 +0530)]
cxgb4/cxgb4vf: support for XLAUI Port Type
Add support for new Backplane XLAUI port type.
Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ganesh Goudar [Thu, 28 Dec 2017 05:59:52 +0000 (11:29 +0530)]
cxgb4: display VNI correctly
Fix incorrect VNI display in mps_tcam
Signed-off-by: Santosh Rastapur <santosh@chelsio.com> Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Bloch [Thu, 7 Dec 2017 20:55:10 +0000 (20:55 +0000)]
net/mlx5e: Move ethernet representors data into separate struct
Ethernet representors have a need to store data which is applicable
only for them. Create a priv void pointer in struct mlx5_eswitch_rep
and move mlx5e to store the relevant data there. As part of this change
we also initialize rep_if in mlx5e_rep_register_vf_vports() as otherwise the
E-Switch code will copy a priv value which is garbage.
We also rename mlx5_eswitch_get_uplink_netdev() to
mlx5_eswitch_get_uplink_priv() and make it return void *.
This way E-Switch code doesn't need to deal with net devices and
we leave the task of getting it to mlx5e.
Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mark Bloch [Thu, 7 Dec 2017 15:36:59 +0000 (15:36 +0000)]
net/mlx5: E-Switch, Create a dedicated send to vport rule deletion function
In order for representors to send packets directly to VFs we use an
E-Switch function which insert special rules into the HW. For symmetry
create an E-Switch function that deletes these rules as well.
Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Mark Bloch [Thu, 7 Dec 2017 15:31:50 +0000 (15:31 +0000)]
net/mlx5: E-Switch, Move mlx5e only logic outside E-Switch
In our pursuit to cleanup e-switch sub-module from mlx5e specific code,
we move the functions that insert/remove the flow steering rules that
allow mlx5e representors to send packets directly to VFs into the EN
driver code.
Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the init stage of vport representors registration.
vport number and hw id can be assigned by the E-Switch driver and not by
the netdevice driver. While here, make the error path of mlx5_eswitch_init()
a reverse order of the good path, also use kcalloc to allocate an array
instead of kzalloc.
Signed-off-by: Mark Bloch <markb@mellanox.com> Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fixes: 482d2e9c1cc7 ("net: hns3: add support to query tqps number") Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Fix incorrect state pruning related to recognition of zero initialized
stack slots, where stacksafe exploration would mistakenly return a
positive pruning verdict too early ignoring other slots, from Gianluca.
2) Various BPF to BPF calls related follow-up fixes. Fix an off-by-one
in maximum call depth check, and rework maximum stack depth tracking
logic to fix a bypass of the total stack size check reported by Jann.
Also fix a bug in arm64 JIT where prog->jited_len was uninitialized.
Addition of various test cases to BPF selftests, from Alexei.
3) Addition of a BPF selftest to test_verifier that is related to BPF to
BPF calls which demonstrates a late caller stack size increase and
thus out of bounds access. Fixed above in 2). Test case from Jann.
4) Addition of correlating BPF helper calls, BPF to BPF calls as well
as BPF maps to bpftool xlated dump in order to allow for better
BPF program introspection and debugging, from Daniel.
5) Fixing several bugs in BPF to BPF calls kallsyms handling in order
to get it actually to work for subprogs, from Daniel.
6) Extending sparc64 JIT support for BPF to BPF calls and fix a couple
of build errors for libbpf on sparc64, from David.
7) Allow narrower context access for BPF dev cgroup typed programs in
order to adapt to LLVM code generation. Also adjust memlock rlimit
in the test_dev_cgroup BPF selftest, from Yonghong.
8) Add netdevsim Kconfig entry to BPF selftests since test_offload.py
relies on netdevsim device being available, from Jakub.
9) Reduce scope of xdp_do_generic_redirect_map() to being static,
from Xiongwei.
10) Minor cleanups and spelling fixes in BPF verifier, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 27 Dec 2017 23:36:49 +0000 (15:36 -0800)]
nfp: bpf: allocate vNIC priv for keeping track of the offloaded program
After TC offloads were converted to callbacks we have no choice
but keep track of the offloaded filter in the driver.
Since this change came a little late in the release cycle
there were a number of conflicts and allocation of vNIC priv
structure seems to have slipped away in linux-next.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two small fixes for bpftool. Fix otherwise broken output if any of
the system calls failed when listing maps in json format and instead
of bailing out, skip maps or progs that disappeared between fetching
next id and getting an fd for that id, both from Jakub.
2) Small fix in BPF selftests to respect LLC passed from command line
when testing for -mcpu=probe presence, from Quentin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nitzan Carmi [Tue, 26 Dec 2017 09:20:20 +0000 (11:20 +0200)]
IB/mlx5: Fix mlx5_ib_alloc_mr error flow
ibmr.device is being set only after ib_alloc_mr() is
(successfully) complete. Therefore, in case mlx5_core_create_mkey()
return with error, the error flow calls mlx5_free_priv_descs()
which uses ibmr.device (which doesn't exist yet), causing
a NULL dereference oops.
To fix this, the IB device should be set in the mr struct earlier
stage (e.g. prior to calling mlx5_core_create_mkey()).
Fixes: 8a187ee52b04 ("IB/mlx5: Support the new memory registration API") Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Nitzan Carmi <nitzanc@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Moni Shoua [Sun, 24 Dec 2017 11:54:58 +0000 (13:54 +0200)]
IB/core: Verify that QP is security enabled in create and destroy
The XRC target QP create flow sets up qp_sec only if there is an IB link with
LSM security enabled. However, several other related uAPI entry points blindly
follow the qp_sec NULL pointer, resulting in a possible oops.
Check for NULL before using qp_sec.
Cc: <stable@vger.kernel.org> # v4.12 Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs") Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Moni Shoua [Sun, 24 Dec 2017 11:54:57 +0000 (13:54 +0200)]
IB/uverbs: Fix command checking as part of ib_uverbs_ex_modify_qp()
If the input command length is larger than the kernel supports an error should
be returned in case the unsupported bytes are not cleared, instead of the
other way aroudn. This matches what all other callers of ib_is_udata_cleared
do and will avoid user ABI problems in the future.
Cc: <stable@vger.kernel.org> # v4.10 Fixes: 189aba99e700 ("IB/uverbs: Extend modify_qp and support packet pacing") Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Majd Dibbiny [Sun, 24 Dec 2017 11:54:56 +0000 (13:54 +0200)]
IB/mlx5: Serialize access to the VMA list
User-space applications can do mmap and munmap directly at
any time.
Since the VMA list is not protected with a mutex, concurrent
accesses to the VMA list from the mmap and munmap can cause
data corruption. Add a mutex around the list.
Cc: <stable@vger.kernel.org> # v4.7 Fixes: 7c2344c3bbf9 ("IB/mlx5: Implements disassociate_ucontext API") Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Yafang Shao [Sun, 24 Dec 2017 15:10:39 +0000 (23:10 +0800)]
net/trace: fix printk format in inet_sock_set_state
There's a space character missed in the printk messages.
Put the message into one line could simplify searching for
the messages in the kernel source.
Fixes: 563e0bb0dc74("net: tracepoint: replace tcp_set_state tracepoint with inet_sock_set_state tracepoint") Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Dec 2017 21:44:14 +0000 (16:44 -0500)]
Merge branch 'net-zerocopy-refine'
Willem de Bruijn says:
====================
zerocopy refinements
1/4 is a small optimization follow-up to the earlier fix to skb_segment:
check skb state once per skb, instead of once per frag.
2/4 makes behavior more consistent between standard and zerocopy send:
set the PSH bit when hitting MAX_SKB_FRAGS. This helps GRO.
3/4 resolves a surprising inconsistency in notification:
because small packets were not stored in frags, they would not set
the copied error code over loopback. This change also optimizes
the path by removing copying and making tso_fragment cheaper.
4/4 follows-up to 3/4 by no longer allocated now unused memory.
this was actually already in RFC patches, but dropped as I pared
down the patch set during revisions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 23 Dec 2017 00:00:19 +0000 (19:00 -0500)]
tcp: place all zerocopy payload in frags
This avoids an unnecessary copy of 1-2KB and improves tso_fragment,
which has to fall back to tcp_fragment if skb->len != skb_data_len.
It also avoids a surprising inconsistency in notifications:
Zerocopy packets sent over loopback have their frags copied, so set
SO_EE_CODE_ZEROCOPY_COPIED in the notification. But this currently
does not happen for small packets, because when all data fits in the
linear fragment, data is not copied in skb_orphan_frags_rx.
Reported-by: Tom Deseyn <tom.deseyn@gmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 23 Dec 2017 00:00:18 +0000 (19:00 -0500)]
tcp: push full zerocopy packets
Skbs that reach MAX_SKB_FRAGS cannot be extended further. Do the
same for zerocopy frags as non-zerocopy frags and set the PSH bit.
This improves GRO assembly.
Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Sat, 23 Dec 2017 00:00:17 +0000 (19:00 -0500)]
skbuff: in skb_segment, call zerocopy functions once per nskb
This is a net-next follow-up to commit 268b79067942 ("skbuff: orphan
frags before zerocopy clone"), which fixed a bug in net, but added a
call to skb_zerocopy_clone at each frag to do so.
When segmenting skbs with user frags, either the user frags must be
replaced with private copies and uarg released, or the uarg must have
its refcount increased for each new skb.
skb_orphan_frags does the first, except for cases that can handle
reference counting. skb_zerocopy_clone then does the second.
Call these once per nskb, instead of once per frag.
That is, in the common case. With a frag list, also refresh when the
origin skb (frag_skb) changes.
Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 27 Dec 2017 21:06:57 +0000 (13:06 -0800)]
Merge tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"While doing tests on tracing over the network, I found that the
packets were getting corrupted.
In the process I found three bugs.
One was the culprit, but the other two scared me. After deeper
investigation, they were not as major as I thought they were, due to a
signed compared to an unsigned that prevented a negative number from
doing actual harm.
The two bigger bugs:
- Mask the ring buffer data page length. There are data flags at the
high bits of the length field. These were not cleared via the
length function, and the length could return a negative number.
(Although the number returned was unsigned, but was assigned to a
signed number) Luckily, this value was compared to PAGE_SIZE which
is unsigned and kept it from entering the path that could have
caused damage.
- Check the page usage before reusing the ring buffer reader page.
TCP increments the page ref when passing the page off to the
network. The page is passed back to the ring buffer for use on
free. But the page could still be in use by the TCP stack.
Minor bugs:
- Related to the first bug. No need to clear out the unused ring
buffer data before sending to user space. It is now done by the
ring buffer code itself.
- Reset pointers after free on error path. There were some cases in
the error path that pointers were freed but not set to NULL, and
could have them freed again, having a pointer freed twice"
* tag 'trace-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix possible double free on failure of allocating trace buffer
tracing: Fix crash when it fails to alloc ring buffer
ring-buffer: Do no reuse reader page if still in use
tracing: Remove extra zeroing out of the ring buffer page
ring-buffer: Mask out the info bits when returning buffer page length
Linus Torvalds [Wed, 27 Dec 2017 20:59:27 +0000 (12:59 -0800)]
Merge tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"It seems that Santa overslept with a bunch of gifts; the majority of
changes here are various device-specific ASoC fixes, most notably the
revert of rcar IOMMU support and fsl_ssi AC97 fixes, but also lots of
small fixes for codecs. Besides that, the usual HD-audio quirks and
fixes are included, too"
* tag 'sound-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (31 commits)
ALSA: hda - Fix missing COEF init for ALC225/295/299
ALSA: hda: Drop useless WARN_ON()
ALSA: hda - change the location for one mic on a Lenovo machine
ALSA: hda - fix headset mic detection issue on a Dell machine
ALSA: hda - Add MIC_NO_PRESENCE fixup for 2 HP machines
ASoC: rsnd: fixup ADG register mask
ASoC: rt5514-spi: only enable wakeup when fully initialized
ASoC: nau8825: fix issue that pop noise when start capture
ASoC: rt5663: Fix the wrong result of the first jack detection
ASoC: rsnd: ssi: fix race condition in rsnd_ssi_pointer_update
ASoC: Intel: Change kern log level to avoid unwanted messages
ASoC: atmel-classd: select correct Kconfig symbol
ASoC: wm_adsp: Fix validation of firmware and coeff lengths
ASoC: Intel: Skylake: Do not check dev_type for dmic link type
ASoC: rockchip: disable clock on error
ASoC: tlv320aic31xx: Fix GPIO1 register definition
ASoC: codecs: msm8916-wcd: Fix supported formats
ASoC: fsl_asrc: Fix typo in a field define
ASoC: rsnd: ssiu: clear SSI_MODE for non TDM Extended modes
ASoC: da7218: Correct IRQ level in DT binding example
...
Matthieu CASTET [Tue, 12 Dec 2017 10:10:44 +0000 (11:10 +0100)]
led: core: Fix brightness setting when setting delay_off=0
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag
echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep
To fix that, when we delete the timer, we should clear LED_BLINK_SW.
Cc: linux-leds@vger.kernel.org Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com> Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
tracing: Fix possible double free on failure of allocating trace buffer
Jing Xia and Chunyan Zhang reported that on failing to allocate part of the
tracing buffer, memory is freed, but the pointers that point to them are not
initialized back to NULL, and later paths may try to free the freed memory
again. Jing and Chunyan fixed one of the locations that does this, but
missed a spot.
Jing Xia [Tue, 26 Dec 2017 07:12:53 +0000 (15:12 +0800)]
tracing: Fix crash when it fails to alloc ring buffer
Double free of the ring buffer happens when it fails to alloc new
ring buffer instance for max_buffer if TRACER_MAX_TRACE is configured.
The root cause is that the pointer is not set to NULL after the buffer
is freed in allocate_trace_buffers(), and the freeing of the ring
buffer is invoked again later if the pointer is not equal to Null,
as:
//if trace_buffer is not null, free again
|-ring_buffer_free(buf->buffer)
|-rb_free_cpu_buffer(buffer->buffers[cpu])
// ring_buffer_per_cpu is null, and
// crash in ring_buffer_per_cpu->pages
ring-buffer: Do no reuse reader page if still in use
To free the reader page that is allocated with ring_buffer_alloc_read_page(),
ring_buffer_free_read_page() must be called. For faster performance, this
page can be reused by the ring buffer to avoid having to free and allocate
new pages.
The issue arises when the page is used with a splice pipe into the
networking code. The networking code may up the page counter for the page,
and keep it active while sending it is queued to go to the network. The
incrementing of the page ref does not prevent it from being reused in the
ring buffer, and this can cause the page that is being sent out to the
network to be modified before it is sent by reading new data.
Add a check to the page ref counter, and only reuse the page if it is not
being used anywhere else.
Cc: stable@vger.kernel.org Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
tracing: Remove extra zeroing out of the ring buffer page
The ring_buffer_read_page() takes care of zeroing out any extra data in the
page that it returns. There's no need to zero it out again from the
consumer. It was removed from one consumer of this function, but
read_buffers_splice_read() did not remove it, and worse, it contained a
nasty bug because of it.
Cc: stable@vger.kernel.org Fixes: 2711ca237a084 ("ring-buffer: Move zeroing out excess in page to ring buffer code") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Dave Airlie [Wed, 27 Dec 2017 19:20:07 +0000 (05:20 +1000)]
Merge tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
GLK pipe C related fix, and a gvt fix.
* tag 'drm-intel-fixes-2017-12-22-1' of git://anongit.freedesktop.org/drm/drm-intel:
i915: Reject CCS modifiers for pipe C on Geminilake
drm/i915/gvt: Fix pipe A enable as default for vgpu
ring-buffer: Mask out the info bits when returning buffer page length
Two info bits were added to the "commit" part of the ring buffer data page
when returned to be consumed. This was to inform the user space readers that
events have been missed, and that the count may be stored at the end of the
page.
What wasn't handled, was the splice code that actually called a function to
return the length of the data in order to zero out the rest of the page
before sending it up to user space. These data bits were returned with the
length making the value negative, and that negative value was not checked.
It was compared to PAGE_SIZE, and only used if the size was less than
PAGE_SIZE. Luckily PAGE_SIZE is unsigned long which made the compare an
unsigned compare, meaning the negative size value did not end up causing a
large portion of memory to be randomly zeroed out.
Cc: stable@vger.kernel.org Fixes: 66a8cb95ed040 ("ring-buffer: Add place holder recording of dropped events") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Tonghao Zhang [Fri, 22 Dec 2017 18:15:20 +0000 (10:15 -0800)]
sctp: Replace use of sockets_allocated with specified macro.
The patch(180d8cd942ce) replaces all uses of struct sock fields'
memory_pressure, memory_allocated, sockets_allocated, and sysctl_mem
to accessor macros. But the sockets_allocated field of sctp sock is
not replaced at all. Then replace it now for unifying the code.
Fixes: 180d8cd942ce ("foundations of per-cgroup memory pressure controlling.") Cc: Glauber Costa <glommer@parallels.com> Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Dec 2017 18:37:28 +0000 (13:37 -0500)]
Merge branch 'rds-bug-fixes'
Sowmini Varadhan says:
====================
rds bug fixes
Ran into pre-existing bugs when working on the fix for
https://www.spinics.net/lists/netdev/msg472849.html
The bugs fixed in this patchset are unrelated to the syzbot
failure (which I'm still testing and trying to reproduce) but
meanwhile, let's get these fixes out of the way.
V2: target net-next (rds:tcp patches have a dependancy on
changes that are in net-next, but not yet in net)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Fri, 22 Dec 2017 17:39:01 +0000 (09:39 -0800)]
rds: tcp: cleanup if kmem_cache_alloc fails in rds_tcp_conn_alloc()
If kmem_cache_alloc() fails in the middle of the for() loop,
cleanup anything that might have been allocated so far.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Fri, 22 Dec 2017 17:39:00 +0000 (09:39 -0800)]
rds: tcp: initialize t_tcp_detached to false
Commit f10b4cff98c6 ("rds: tcp: atomically purge entries from
rds_tcp_conn_list during netns delete") adds the field t_tcp_detached,
but this needs to be initialized explicitly to false.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Fri, 22 Dec 2017 17:38:59 +0000 (09:38 -0800)]
rds; Reset rs->rs_bound_addr in rds_add_bound() failure path
If the rds_sock is not added to the bind_hash_table, we must
reset rs_bound_addr so that rds_remove_bound will not trip on
this rds_sock.
rds_add_bound() does a rds_sock_put() in this failure path, so
failing to reset rs_bound_addr will result in a socket refcount
bug, and will trigger a WARN_ON with the stack shown below when
the application subsequently tries to close the PF_RDS socket.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sudip Mukherjee [Fri, 22 Dec 2017 15:52:05 +0000 (15:52 +0000)]
net: sch: api: fix tcf_block_get
The build of mips bcm47xx_defconfig is failing with the error:
net/sched/sch_fq_codel.c: In function 'fq_codel_init':
net/sched/sch_fq_codel.c:487:8: error:
too many arguments to function 'tcf_block_get'
While adding the extack support, the commit missed adding it in the
headers when CONFIG_NET_CLS is not defined.
Fixes: 8d1a77f974ca ("net: sch: api: add extack support in tcf_block_get") Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 27 Dec 2017 17:36:23 +0000 (18:36 +0100)]
Merge branch 'bpf-stack-depth-tracking-fixes'
Alexei Starovoitov says:
====================
Jann reported an issue with stack depth tracking. Fix it and add tests.
Also fix off-by-one error in MAX_CALL_FRAMES check. This set is on top
of Jann's "selftest for late caller stack size increase" test.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Instead of computing max stack depth for current call chain
during the main verifier pass track stack depth of each
function independently and after do_check() is done do
another pass over all instructions analyzing depth
of all possible call stacks.
Fixes: f4d7e40a5b71 ("bpf: introduce function calls (verification)") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jann Horn [Fri, 22 Dec 2017 18:12:35 +0000 (19:12 +0100)]
bpf: selftest for late caller stack size increase
This checks that it is not possible to bypass the total stack size check in
update_stack_depth() by calling a function that uses a large amount of
stack memory *before* using a large amount of stack memory in the caller.
Currently, the first added testcase causes a rejection as expected, but
the second testcase is (AFAICS incorrectly) accepted:
[...]
#483/p calls: stack overflow using two frames (post-call access) FAIL
Unexpected success to load!
0: (85) call pc+2
caller:
R10=fp0,call_-1
callee:
frame1: R1=ctx(id=0,off=0,imm=0) R10=fp0,call_0
3: (72) *(u8 *)(r10 -300) = 0
4: (b7) r0 = 0
5: (95) exit
returning from callee:
frame1: R0_w=inv0 R1=ctx(id=0,off=0,imm=0) R10=fp0,call_0
to caller at 1:
R0_w=inv0 R10=fp0,call_-1