Arnd Bergmann [Thu, 20 Dec 2018 15:34:06 +0000 (16:34 +0100)]
Merge tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add interconnect target module dts data for omaps for v4.21
This big set of changes adds SoC specific l4 interconnect target module
device tree data for am335x, am437x, omap5 and dra7 SoCs. We also move
existing devices to the right location in the l4 interconnect hierarcy.
This is similar to what we've already done for omap4 l4 interconnects
earlier, and follows what is documented in the ti-sysc driver dts binding
in Documentation/devicetree/bindings/bus/ti-sysc.txt.
These changes will essentially replace the struct ti_sysc and clock
entries in the arch/arm/mach-omap2/omap_hwmod_*_data.c files. Then a few
merge windows later, we can start dropping the built-in platform data
from the omap_hwmod_*_data.c files in favor of the device tree data only.
For now, we verify the device tree data module data against the built-in
data and warn about changes to prevent regressions.
With the device tree data, we are also probing devices with the ti-sysc
interconnect target module instead of omap_device. This fixes up the
handling for multiple device instances in a single interconnect target
module that has caused trouble earlier. A custom wrapper driver has been
needed earlier for such cases.
And as the device tree data is organized by the l4 interconnect instances,
we will be able to use genpd later on. This is because each interconnect
instance is also often also a single power domain.
This series of changes has been brewing for several months now. I did not
want to send a pull request earlier as people were still seeing device
specific issues until recently though. However, it turned out that all the
issues were quite trivial to fix. I had missed adding device tree ranges
for the l3 data port used on some devices, and I had missed converting the
device addresses for a few devices. And some devices like needed fixes for
deferred probe handling such as the EHCI PHY for built-in case on omap5.
Anyways, in case of trouble, we can easily just revert changes for a
single device if needed.
* tag 'omap-for-v4.21/dt-ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Cosmetic fix for omap5 USB node names
ARM: dts: Fix wrong address for omap5 sata phy
ARM: dts: Add missing ranges for dra7 mcasp l3 ports
ARM: dts: Fix ranges for am335x epwmss
ARM: dts: Fix hsi gdd range for omap4
ARM: dts: Add am335x mcasp with l3 data port ranges
ARM: dts: Add missing ranges for am437x mcasp l3 ports
ARM: dts: dra7: Move the ti,no-idle quirk on proper gmac node
ARM: dts: Revert am335x mcasp ti-sysc changes
ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: Use dra7 mcasp compatible for mcasp instances
ARM: dts: dra7: Move l4 child devices to probe them with ti-sysc
ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am335x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am335x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: am437x: Move l4 child devices to probe them with ti-sysc
ARM: dts: am437x: Add l4 interconnect hierarchy and ti-sysc data
ARM: dts: dra7: convert to use new clkctrl layout
ARM: dts: am43xx: convert to use new clkctrl layout
ARM: dts: am33xx: convert to use new clkctrl layout
Vignesh R [Wed, 12 Dec 2018 05:18:06 +0000 (10:48 +0530)]
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
Populate power-domain property for UART nodes, this is required for
Linux to enable UART clocks via PM calls. Without this UART instances
not initialized by bootloader (like main_uart1) fails to work in Linux.
Also, drop current-speed property from main_uart1 and main_uart2 nodes
as these UARTs are not initialized before Linux boots up and current
speed is unknown.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com>
Rob Herring [Wed, 12 Dec 2018 08:50:11 +0000 (09:50 +0100)]
dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema
Convert Rockchip SoC bindings to DT schema format using json-schema.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-rockchip@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org>
[move to per-board entries after confirming with Rob
and added recently added boards] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Wed, 12 Dec 2018 22:01:03 +0000 (14:01 -0800)]
Merge tag 'gemini-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Gemini DTS updates for v4.21:
- Fix the erroneous partition table on D-Link DIR-685
- Multiplex flash usage with other usage using pin control
handling (merged to the MTD tree)
- Use the RedBoot partition parser on SQ201
- Add the USB blocks (DT bindings merged in the last merge
window)
- Bump the debounce times a bit to avoid bouncing
* tag 'gemini-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Bump Gemini platforms to use 100ms debounce
ARM: dts: Add the FOTG210 USB host to Gemini boards
ARM: dts: Fix up SQ201 flash access
ARM: dts: Enable Gemini flash access
ARM: dts: Fix up the D-Link DIR-685 MTD partition info
Olof Johansson [Wed, 12 Dec 2018 21:07:51 +0000 (13:07 -0800)]
Merge tag 'v4.21-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Support for the onboard LEDs of the 2 96boards (ficus, rock960),
hdmi output for rockpro64, vpu node on rk3399 and adding the
always on 32kHz clock on rk3399-Gru to get a more complete clock
tree.
* tag 'v4.21-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add on-board LED support on rk3399-rock960
arm64: dts: rockchip: Add on-board LED support on rk3399-ficus
arm64: dts: rockchip: enable hdmi output on rk3399-rockpro64
arm64: dts: rockchip: add VPU device node for RK3399
arm64: dts: rockchip: Add 32k clk on rk3399-gru
Olof Johansson [Wed, 12 Dec 2018 21:06:47 +0000 (13:06 -0800)]
Merge tag 'v4.21-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
RV1108 improvements (uart-dma, clocks, interrupt numbers, gmac support
timer and emmc pins) from its first real-world user.
RK3188 improvements (OPPv2, cpu node updates) to prepare for a new
devicetree, the BQ Edison 2 Quad-Core.
VPU device node for rk3288, right now only the jpeg encoder part
will be in the kernel but hopefully other codecs will follow.
* tag 'v4.21-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add internal timer support for rv1108
ARM: dts: rockchip: add BQ Edison 2 QC devicetree
ARM: dts: rockchip: add VPU device node for RK3288
ARM: dts: rockchip: update cpu supplies on rk3188
ARM: dts: rockchip: add phandles to secondary cpu cores
ARM: dts: rockchip: add cpu-core resets for rk3188
ARM: dts: rockchip: convert rk3188 to opp-v2
ARM: dts: rockchip: add #sound-dai-cells to Cortex-A9 i2s
ARM: dts: rockchip: Add UART DMA support for rv1108
ARM: dts: rockchip: Assign the proper GPIO clocks for rv1108
ARM: dts: rockchip: Fix the PMU interrupt number for rv1108
ARM: dts: rockchip: Pass the 'arm,cpu-registers-not-fw-configured' property on rv1108
ARM: dts: rockchip: Pass the 'clock-latency' property on rv1108
ARM: dts: rockchip: Add rv1108 GMAC support
ARM: dts: rockchip: add rv1108 eMMC pin settings
Olof Johansson [Wed, 12 Dec 2018 21:04:41 +0000 (13:04 -0800)]
Merge tag 'at91-4.21-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/dt
AT91 DT for 4.21
- Switch most platforms to the new clock binding
- Small improvement for Axentia nattis
* tag 'at91-4.21-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: nattis: initialize the BLON pin as output-low early
ARM: dts: at91: at91sam9rl: switch to new clock bindings
ARM: dts: at91: at91sam9x5: switch to new clock bindings
ARM: dts: at91: at91sam9263: switch to new clock bindings
ARM: dts: at91: at91sam9261: switch to new clock bindings
ARM: dts: at91: at91sam9260: switch to new clock bindings
ARM: dts: at91: sama5d2: switch to new clock binding
ARM: dts: at91: sama5d4: switch to new clock bindings
ARM: dts: at91: sama5d2: use the divided clock for SMC
Olof Johansson [Wed, 12 Dec 2018 21:02:51 +0000 (13:02 -0800)]
Merge tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
ARM: dts: Amlogic updates for v4.21, round 2
Highlights
- add CPU OPP tables
- timers: add global timer and TWD
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson: meson8b: add the CPU OPP tables
ARM: dts: meson: meson8: add the CPU OPP table
ARM: dts: meson8b: add the Cortex-A5 global timer
ARM: dts: meson8b: add the ARM TWD timer
ARM: dts: meson8: add the Cortex-A9 global timer
ARM: dts: meson8: add the ARM TWD timer
ARM: dts: meson: group the Cortex-A5 / Cortex-A9 peripherals
dt-bindings: clock: meson8b: export the CPU post dividers
Olof Johansson [Wed, 12 Dec 2018 21:01:24 +0000 (13:01 -0800)]
Merge tag 'uniphier-dt-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.21
- Add bindings for all SoCs/boards of UniPhier platform
- Move binding docs to socionext directory
- Add all CPUs in cooling maps
- Add MIO DMAC nodes
* tag 'uniphier-dt-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add MIO DMAC nodes
arm64: dts: uniphier: Add all CPUs in cooling maps
ARM: dts: uniphier: Add all CPUs in cooling maps
dt-bindings: uniphier: move cache-uniphier.txt to vendor directory
dt-bindings: uniphier: add bindings for UniPhier SoC family
Olof Johansson [Wed, 12 Dec 2018 20:59:14 +0000 (12:59 -0800)]
Merge tag 'imx-dt64-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Freescale arm64 device tree update for 4.21:
- Add device tree for LS1028A SoC and NXP FRWY & QDS boards support
based on this SoC.
- Add device tree for LX2160A SoC and NXP QDS & RDB boards support
based on this SoC.
- Add qdma devices for LS1043A and LS1046A SoC.
- Disable PCIe device by default in SoC device tree and let board level
device tree to enable as needed.
- Drop compatible string "snps,dw-pcie" from LayerScape PCIe devices to
avoid incorrect matching.
- Move fsl-mc device as a child node of soc node, and add missing
dma-ranges property for LS1088A SoC.
- Update LayerScape SoCs' cooling maps to include all devices affected
by individual trip points.
* tag 'imx-dt64-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls1046a: add qdma device tree nodes
arm64: dts: ls1043a: add qdma device tree nodes
arm64: dts: ls1088a: Add missing dma-ranges property
arm64: dts: ls1088a: Move fsl-mc node
arm64: dts: fsl: Add all CPUs in cooling maps
arm64: dts: Add support for NXP LS1028A SoC
arm64: dts: layerscape: removed compatible string "snps,dw-pcie"
arm64: dts: fsl: Add the status property disable PCIe
arm64: dts: ls1012a: Add FRWY-LS1012A board support
arm64: dts: add LX2160AQDS board support
arm64: dts: add LX2160ARDB board support
arm64: dts: add QorIQ LX2160A SoC support
Olof Johansson [Wed, 12 Dec 2018 20:55:34 +0000 (12:55 -0800)]
Merge tag 'imx7d-pico-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX7D PICO boards update for 4.21:
- It contains a series from Otavio Salvador that improves i.MX7D PICO
SoM, and then adds Hobbit baseboard support on top of the improvement.
* tag 'imx7d-pico-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-pico: Add the imx7d-pico-hobbit variant
ARM: dts: imx7d-pico-pi: Extend peripherals support
ARM: dts: imx7d-pico: Extend peripherals support
ARM: dts: imx7d-pico: Improve WiFi regulator name
ARM: dts: imx7d-pico: Pass the Ethernet PHY reset GPIO
ARM: dts: imx7d-pico: Pass the USBOTG1_PWR pinctrl
ARM: dts: imx7d-pico-pi: Move SoM related part to imx7d-pico.dtsi
ARM: dts: imx7d-pico: Switch to SPDX identifier
ARM: dts: imx7d-pico: Do not harcode the memory size
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
Olof Johansson [Wed, 12 Dec 2018 20:54:48 +0000 (12:54 -0800)]
Merge tag 'imx-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.21:
- New boards support: emtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
and vf610 based Liebherr's BK4 device, ZII SCU4 AIB board.
- Add flexcan support for i.MX6UL SoC, turn on stop mode wakeup feature
for flexcan, and enable devices on a few i.MX6 NXP boards.
- Enable AUO G101EVN010 lcd panel and Goodix touch support for
imx6ul-ccimx6ulsbcpro board.
- Enable sensors support for imx6qdl-sabresd board: egalax touch, light,
magnetometer and accelerometer sensor.
- Switch more boards to use SPDX identifier.
- Fix memory node duplication in i.MX device tree sources.
- Correct GIC PPI interrupts mask for i.MX6UL and i.MX7 SoCs.
- Drop 'snps,dw-pcie' compatible from LS1021A PCIe device to avoid
incorrect device matching.
- Add the gpu nodes for the adreno 200 GPU on iMX51 and iMX53, which
are now supported by the freedreno driver.
- Add DCP device support for i.MX6ULL, which requires explicit clock
enabling.
- Add '#thermal-sensor-cells' for thermal device and '#cooling-cells'
for cooling devices.
- Add missing clock information for EPIT on i.MX25 SoC.
- Add PWM and qdma devices for LS1021A SoC.
- Update cooling maps of LS1021A SoC to include all devices affected by
individual trip points.
- Random device addition and cleanup on various boards.
* tag 'imx-dt-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (82 commits)
ARM: dts: imx51-zii-rdu1: Do not specify "power-gpio" for hpa1
ARM: dts: imx6ul: Remove extra space between node name and brace
ARM: dts: imx6qdl-sabresd: Use GPIO_ACTIVE_HIGH for regulators
ARM: dts: imx6ul: add flexcan support
ARM: dts: imx5: add gpu nodes
ARM: dts: imx6qdl-sabresd: add accelerometer sensor support
ARM: dts: imx6qdl-sabresd: add magnetometer sensor support
ARM: dts: imx6qdl-sabresd: add light sensor support
ARM: dts: imx6qdl-sabresd: Move regulators outside of "simple-bus"
ARM: dts: imx6qdl: Fix memory node duplication
ARM: dts: imx6dl-mamoj: Add a memory node
ARM: dts: imx53-voipac-dmm-668: Fix memory node duplication
ARM: dts: vf610-zii-scu4-aib: Add HI8435 support
ARM: dts: imx6qdl-sabresd: add egalax touch screen support on i2c2 bus
ARM: dts: imx7s: Add flexcan stop mode wakeup support
ARM: dts: imx6ul: Add flexcan stop mode wakeup support
ARM: dts: imx6qdl: Add flexcan stop mode wakeup support
ARM: dts: imx6sx: Add flexcan stop mode wakeup support
ARM: dts: imx6ul-pico: Add the imx6ul-pico-pi variant
ARM: dts: imx6ul-pico-hobbit: Extend peripherals support
...
Olof Johansson [Wed, 12 Dec 2018 20:53:05 +0000 (12:53 -0800)]
Merge tag 'samsung-dt64-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM64 changes for v4.21
1. Update DWC3 hardware modules to Exynos5433 specific variant.
2. Update cooling maps to include all CPU devices in multiple DTS files.
* tag 'samsung-dt64-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add all CPUs in cooling maps
arm64: dts: exynos: Update DWC3 modules on Exynos5433 SoCs
Olof Johansson [Wed, 12 Dec 2018 20:52:20 +0000 (12:52 -0800)]
Merge tag 'samsung-dt-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.21
1. Add missing properties and nodes for PMIC clocks in multiple DTS
files.
2. Add UHS-I bus speed support to Odroid XU3/XU4/HC SD card and bump the
maximum clock frequency to 200 MHz for SD and eMMC.
3. Update cooling maps to include all CPU devices in multiple DTS files.
4. Enable quirks for Exynos3250 DWC.
5. Add JPEG CODEC node to S5Pv210.
6. Add opp-suspend to devfreq OPPs on Exynos4 boards to fix resuming
from suspend to RAM.
7. Remove eDP from Arndale board as it does not work and breaks also
DSI.
* tag 'samsung-dt-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Olof Johansson [Wed, 12 Dec 2018 20:51:46 +0000 (12:51 -0800)]
Merge tag 'mvebu-dt64-4.21-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.21 (part 1)
- complete the description of the clearfog-gt-8k board (Armada 8040
based board)
- declare eMMC on espressobin (Armada 3720 based board) which still
need to be enable by the bootloader as it is not present on all the
board.
- add a new version of the Macchiatobin (Armada 8040 based board): the
Single Shot (without the 10G 3310 PHYs).
* tag 'mvebu-dt64-4.21-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: describe mini-PCIe CON2 USB
arm64: dts: add support for Macchiatobin Single Shot board
arm64: dts: marvell: armada-37xx: Enable emmc on espressobin
arm64: dts: marvell: armada37xx: Add emmc/sdio pinctrl definition
arm64: dts: clearfog-gt-8k: enable mini-PCIe CON2 USB
arm64: dts: clearfog-gt-8k: 1G eth PHY reset signal
arm64: dts: clearfog-gt-8k: fix USB regulator gpio polarity
Olof Johansson [Wed, 12 Dec 2018 20:50:46 +0000 (12:50 -0800)]
Merge tag 'qcom-arm64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm ARM64 Updates for v4.21 Part 2
* Switch to use dwc3-qcom glue driver on MSM8996
* Fix issue with xo clk name on MSM8998
* Add cooling maps on MSM8916
* Add UART nodes on SDM845
* Add camera subsystem support on MSM8996 and MSM8916
* tag 'qcom-arm64-for-4.21-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: msm8996: Use dwc3-qcom glue driver for USB
arm64: dts: qcom: msm8998: Fixup clock to use xo_board
arm64: dts: qcom: sdm845: Add UART nodes
arm64: dts: qcom: msm8996: Add CAMSS support
arm64: dts: qcom: msm8996: Add VFE SMMU node
arm64: dts: qcom: Add pinctrls for camera sensors
arm64: dts: qcom: Add Camera Control Interface pinctrls
arm64: dts: qcom: msm8916: Add CAMSS support
arm64: dts: qcom: msm8916: Add IOMMU sub-node for VFE context bank
arm64: dts: msm8916: Add all CPUs in cooling maps
Olof Johansson [Wed, 12 Dec 2018 20:50:00 +0000 (12:50 -0800)]
Merge tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.21
Our usual set of arm64 DT changes, with the biggest additions being:
- Support for the video decoding engine in the A64
- Support for the audio codec in the A64
- USB Support in the H6
- HDMI Support in the H6
- EMAC Support in the H6
- New board: Orange Pi Lite2
* tag 'sunxi-dt64-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (27 commits)
arm64: dts: allwinner: a64: Fix up RTC device node and clock references
arm64: dts: allwinner: a64: Add Video Engine node
arm64: dts: allwinner: a64: Add support for the SRAM C1 section
arm64: dts: allwinner: a64: pinebook: enable power supplies
arm64: dts: allwinner: a64: sopine-baseboard: enable power supplies
arm64: dts: allwinner: axp803: add AC and battery power supplies
arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec
arm64: dts: allwinner: a64: enable sound on Pinebook
arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine
arm64: dts: allwinner: a64: add nodes necessary for analog sound support
arm64: dts: allwinner: h6: orangepi: Add device nodes for LEDs
arm64: dts: allwinner: h6: orangepi: Enable USB 2.0 host and OTG ports
arm64: dts: allwinner: h6: orangepi: Add board-wide 5V regulator
arm64: dts: allwinner: h6: fix EMAC compatible string sequence
arm64: dts: allwinner: a64: Add device node for Mali-400 GPU
dt-bindings: gpu: mali-utgard: Add compatible for A64 Mali
arm64: dts: allwinner: h6: enable USB2 on Pine H64
arm64: dts: allwinner: h6: add USB Vbus regulator for Pine H64
arm64: dts: allwinner: h6: add USB2-related device nodes
arm64: dts: allwinner: h6: Enable HDMI output on Pine H64 board
...
Olof Johansson [Wed, 12 Dec 2018 20:48:57 +0000 (12:48 -0800)]
Merge tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT changes for 4.21
This is a quite big pull request this time, with a huge number of changes
(and patches) due to us fixing the vast majority of the DTC warnings our DT
had.
We also have a bunch of other good, more meaningful, changes:
- Support for the new Allwinner T3 (rebranded R40) and f1c100s (armv5)
SoCs
- AXP803 PMIC AC Power supply support
- Rework of the oscillators tree
- Two new boards: the t3-cqa3t-bv3 and Lichee Pi Nano
Plus a few enhancements here and there.
* tag 'sunxi-dt-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (84 commits)
ARM: dts: sunxi: Fix PMU compatible strings
ARM: dts: sun8i: r40: Add RTC device node
ARM: dts: sunxi: h3/h5: Fix up RTC device node and clock references
ARM: dts: sun8i: a23/a33: Fix up RTC device node
ARM: dts: sun8i: r40: Add clock accuracy for external oscillators
ARM: dts: sunxi: h3/h5: Add clock accuracy for external oscillators
ARM: dts: sun8i: a33: Drop audio codec oversampling rate to 128 fs
ARM: dts: sun8i: h3: Remove unnecessary reserved memory node
ARM: dts: sun8i: a33: Remove unnecessary reserved memory node
ARM: dts: suniv: Add device tree for Lichee Pi Nano
ARM: dts: suniv: add initial DTSI file for F1C100s
ARM: dts: axp81x: add AC power supply subnode
ARM: dts: sun8i: v3s: Remove skeleton and memory to avoid warnings
ARM: dts: sun8i: v3s: Provide default muxing for relevant controllers
ARM: dts: sun8i: v3s: Change pinctrl nodes to avoid warning
ARM: dts: sun8i: v3s: Change LRADC node names to avoid warnings
ARM: dts: sun8i: h3: Remove leading zeros from unit-addresses
ARM: dts: sun8i: BPI-M2M: Remove i2c nodes
ARM: dts: sun8i: a23/a33: Provide default muxing for relevant controllers
ARM: dts: sunxi: reference: Move the muxing back to the common DTSI
...
Olof Johansson [Tue, 11 Dec 2018 16:10:09 +0000 (08:10 -0800)]
Merge tag 'tegra-for-4.21-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
arm64: tegra: Device tree change for v4.21-rc1
These changes add a bunch of features for Tegra194 and Tegra186, such as
wake events, on-die RTC, temperature sensors, HDA for audio over HDMI
and fan support on Jetson Xavier to allow cooling of the device.
* tag 'tegra-for-4.21-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (29 commits)
arm64: tegra: Set reg property for display-hub on Tegra194
arm64: tegra: Set reg property for display-hub on Tegra186
arm64: dts: tegra186: Enable IOMMU for SDHCI
arm64: tegra: Enable HDA controller on Jetson TX1
arm64: tegra: Add CEC controller on Tegra194
arm64: tegra: Enable HDA on Jetson Xavier
arm64: tegra: Add HDA controller on Tegra194
arm64: tegra: Add CEC controller on Tegra186
arm64: tegra: Enable HDA on Jetson TX2
arm64: tegra: Add HDA controller on Tegra186
arm64: tegra: Add temperature sensor on P2888
arm64: tegra: Add gpio-keys on Jetson Xavier
arm64: tegra: Add AON GPIO controller on Tegra194
arm64: tegra: p2888: Enable on-die RTC
arm64: tegra: Add RTC support on Tegra194
arm64: tegra: Enable PMC wake events on Tegra194
arm64: tegra: p3310: Enable on-die RTC
arm64: tegra: Add RTC support on Tegra186
arm64: tegra: Enable PMC wake events on Tegra186
arm64: tegra: Fix power key interrupt type on Jetson TX2
...
Olof Johansson [Tue, 11 Dec 2018 16:05:01 +0000 (08:05 -0800)]
Merge tag 'renesas-dt-bindings-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Bindings Updates for v4.21
* Move 'renesas,prr' binding to its own document
- Prepration for converting board-level bindings to json-schema
* Document iW-RainboW-G20D-Qseven-RZG1N board and iWave RZ/G1N SOM
* tag 'renesas-dt-bindings-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: arm: renesas: Move 'renesas,prr' binding to its own doc
dt-bindings: arm: renesas: Document iW-RainboW-G20D-Qseven-RZG1N board
dt-bindings: arm: renesas: Document iWave RZ/G1N SOM
Olof Johansson [Tue, 11 Dec 2018 15:43:46 +0000 (07:43 -0800)]
Merge tag 'pxa-dt-4.21' of https://github.com/rjarzmik/linux into next/dt
This device-tree pxa update brings :
- various fixes from Daniel (W=12 issues mainly)
- support for the first pxa3xx devicetree pxa board
* tag 'pxa-dt-4.21' of https://github.com/rjarzmik/linux:
ARM: dts: pxa3xx: Add Raumfeld DTS files
ARM: dts: pxa: clean up USB controller nodes
ARM: dts: pxa3xx: clean up pxa3xx clock controller node name
ARM: dts: pxa3xx: order timer and gcu nodes under /pxabus
ARM: dts: pxa2xx: fix hwuart memory range
ARM: dts: pxa3xx: drop #address-cells and #size-cells from pinctrl node
ARM: dts: pxa2xx: drop #address-cells and #size-cells from /cpus
ARM: dts: pxa3xx: add gcu node
Tony Lindgren [Sat, 8 Dec 2018 00:52:46 +0000 (16:52 -0800)]
ARM: dts: Add missing ranges for dra7 mcasp l3 ports
We need to add mcasp l3 port ranges for mcasp to use a correct l3
data port address for dma. And we're also missing the optional clocks
that we have tagged with HWMOD_OPT_CLKS_NEEDED in omap_hwmod_7xx_data.c.
Note that for reading the module revision register HWMOD_OPT_CLKS_NEEDED
do not seem to be needed. So they could be probably directly managed
only by the mcasp driver, and then we could leave them out for the
interconnect target module.
Fixes: 4ed0dfe3cf39 ("ARM: dts: dra7: Move l4 child devices to probe
them with ti-sysc") Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Mon, 10 Dec 2018 21:43:11 +0000 (13:43 -0800)]
ARM: dts: Fix ranges for am335x epwmss
Looks like I missed the ranges for am335x epwmss. Let's set it up the
same way as for am437x and dra7.
Fixes: 87fc89ced3a7 ("ARM: dts: am335x: Move l4 child devices to probe
them with ti-sysc") Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Viresh Kumar [Fri, 16 Nov 2018 10:04:33 +0000 (15:34 +0530)]
arm64: dts: uniphier: Add all CPUs in cooling maps
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Tony Lindgren [Wed, 5 Dec 2018 22:48:51 +0000 (14:48 -0800)]
ARM: dts: Fix hsi gdd range for omap4
While reviewing the missing mcasp ranges I noticed omap4 hsi range
for gdd is wrong so let's fix it.
I'm not aware of any omap4 devices in mainline kernel though that use
hsi though.
Fixes: 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
A.s. Dong [Sat, 10 Nov 2018 15:13:12 +0000 (15:13 +0000)]
ARM: dts: imx: add imx7ulp evk support
The NXP i.MX 7ULP Evaluation Kit (EVK) provides a platform for rapid
evaluation of the i.MX 7ULP, which features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and
2D Graphics Processing Units (GPUs).
The EVK enables HDMI output for simple out-of-the-box to bring up but
allows reconfiguration for MIPI displays. The EVK is designed as a
System-On-Module(SOM) board that connects to an associated baseboard.
The SOM provides 1 GB LPDDR3, 8 MB Quad SPI flash, Micro SD 3.0 card
socket, WiFi/ Bluetooth capability, USB 2.0 OTG with Type C connector
and an NXP PF1550 power management IC (PMIC). The baseboard provides
additional capabilities including a full SD/MMC 3.0 card socket, audio
codec, multiple sensors, an HDMI connector, and an alternate MIPI display
connector. Additionally, the EVK facilitates software development with the
ultimate goal of faster time to market through the support of both
Linux OS and AndroidTM rich operating systems, as well as FreeRTOS.
This patch aims to support the preliminary booting up features
as follows:
GPIO
LPUART
FEC
SD/MMC
See more board details:
https://www.nxp.com/products/processors-and-microcontrollers/
arm-based-processors-and-mcus/i.mx-applications-processors/
i.mx-7-processors/evaluation-kit-for-the-i.mx-7ulp-applications
-processor:MCIMX7ULP-EVK
A.s. Dong [Sat, 10 Nov 2018 15:13:08 +0000 (15:13 +0000)]
ARM: dts: imx: add common imx7ulp dtsi support
The i.MX 7ULP family of processors features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
Graphics Processing Units (GPUs).
This patch aims to add the initial support including:
1) CLK
2) GPIO PTC, PTD, PTE, PTF
3) uSDHC 1/2
4) LPUART 4/5/6/7
5) LPI2C 6/7
Otavio Salvador [Thu, 6 Dec 2018 10:09:02 +0000 (08:09 -0200)]
ARM: dts: imx7d-pico: Improve WiFi regulator name
There are different models of WiFi being used in the SoM and the
handle name was too restrictive. This reworks it to a more generic and
meaningful name.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Thu, 6 Dec 2018 10:08:57 +0000 (08:08 -0200)]
ARM: dts: imx7d-pico: Do not harcode the memory size
Currently the memory size described in dts is 2GB, which is incorrect.
There are 512MB and 1GB versions of imx7d-pico boards, so remove
the hardcoded memory size and let the bootloader pass the correct
value to the kernel.
Shawn Guo [Mon, 10 Dec 2018 02:32:51 +0000 (10:32 +0800)]
Merge tag 'imx-fixes-4.20-3' into imx7d/pico
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
Andrey Smirnov [Thu, 6 Dec 2018 23:41:17 +0000 (21:41 -0200)]
ARM: dts: imx51-zii-rdu1: Do not specify "power-gpio" for hpa1
TPA6130A2 SD pin on RDU1 is not really controlled by SoC and instead
is only meant to notify the system that audio was "muted" by external
actors. To accommodate that, drop "power-gpio" property of hpa1 node as
well as specify a name for that GPIO so that userspace can access it.
Anson Huang [Thu, 6 Dec 2018 01:42:34 +0000 (01:42 +0000)]
ARM: dts: imx6qdl-sabresd: add light sensor support
Add isl29023 light sensor support on i2c3 bus, the light
sensor's power is controlled by a fixed regulator, since
the isl29023 driver and most of other sensors on same
board like mag3110 and mma8451 do NOT support regulator
operation currently, they are all controlled by this
regulator, so this patch also adds the fixed regulator
support and make it always on.
imx53-voipac-dmm-668 has two memory nodes, but the correct representation
would be to use a single one with two reg entries - one for each RAM chip
select, so fix it accordingly.
Reported-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Aisheng Dong [Wed, 28 Nov 2018 11:03:52 +0000 (11:03 +0000)]
ARM: dts: imx6sx-sabreauto: add flexcan support
The CAN transceiver on MX6SX Sabreauto board seems in sleep mode by default
after power up the board. User has to press the wakeup key on ARD baseboard
before using the transceiver, or it may not work properly when power up the
board at the first time(warm reset does not have such issue).
This patch operates the wake pin too besides stby/en pins by chaining them
together in regulator mode.