Tariq Toukan [Tue, 12 Dec 2017 13:46:49 +0000 (15:46 +0200)]
net/mlx5e: Refactor RQ XDP_TX indication
Make the xdp_xmit indication available for Striding RQ
by taking it out of the type-specific union.
This refactor is a preparation for a downstream patch that
adds XDP support over Striding RQ.
In addition, use a bitmap instead of a boolean for possible
future flags.
Tariq Toukan [Wed, 7 Feb 2018 12:41:25 +0000 (14:41 +0200)]
net/mlx5e: Use linear SKB in Striding RQ
Current Striding RQ HW feature utilizes the RX buffers so that
there is no wasted room between the strides. This maximises
the memory utilization.
This prevents the use of build_skb() (which requires headroom
and tailroom), and demands to memcpy the packets headers into
the skb linear part.
In this patch, whenever a set of conditions holds, we apply
an RQ configuration that allows combining the use of linear SKB
on top of a Striding RQ.
To use build_skb() with Striding RQ, the following must hold:
1. packet does not cross a page boundary.
2. there is enough headroom and tailroom surrounding the packet.
We can satisfy 1 and 2 by configuring:
stride size = MTU + headroom + tailoom.
This is possible only when:
a. (MTU - headroom - tailoom) does not exceed PAGE_SIZE.
b. HW LRO is turned off.
Using linear SKB has many advantages:
- Saves a memcpy of the headers.
- No page-boundary checks in datapath.
- No filler CQEs.
- Significantly smaller CQ.
- SKB data continuously resides in linear part, and not split to
small amount (linear part) and large amount (fragment).
This saves datapath cycles in driver and improves utilization
of SKB fragments in GRO.
- The fragments of a resulting GRO SKB follow the IP forwarding
assumption of equal-size fragments.
Some implementation details:
HW writes the packets to the beginning of a stride,
i.e. does not keep headroom. To overcome this we make sure we can
extend backwards and use the last bytes of stride i-1.
Extra care is needed for stride 0 as it has no preceding stride.
We make sure headroom bytes are available by shifting the buffer
pointer passed to HW by headroom bytes.
This configuration now becomes default, whenever capable.
Of course, this implies turning LRO off.
Performance testing:
ConnectX-5, single core, single RX ring, default MTU.
Tariq Toukan [Sun, 7 Jan 2018 12:15:02 +0000 (14:15 +0200)]
net/mlx5e: Do not busy-wait for UMR completion in Striding RQ
Do not busy-wait a pending UMR completion. Under high HW load,
busy-waiting a delayed completion would fully utilize the CPU core
and mistakenly indicate a SW bottleneck.
Tariq Toukan [Sun, 11 Feb 2018 13:21:33 +0000 (15:21 +0200)]
net/mlx5e: Derive Striding RQ size from MTU
In Striding RQ, each WQE serves multiple packets
(hence called Multi-Packet WQE, MPWQE).
The size of a MPWQE is constant (currently 256KB).
Upon a ringparam set operation, we calculate the number of
MPWQEs per RQ. For this, first it is needed to determine the
number of packets that can reside within a single MPWQE.
In this patch we use the actual MTU size instead of ETH_DATA_LEN
for this calculation.
This implies that a change in MTU might require a change
in Striding RQ ring size.
In addition, this obsoletes some WQEs-to-packets translation
functions and helps delete ~60 LOC.
Tariq Toukan [Mon, 12 Mar 2018 12:24:41 +0000 (14:24 +0200)]
net/mlx5e: Save MTU in channels params
Knowing the MTU is required for RQ creation flow.
By our design, channels creation flow is totally isolated
from priv/netdev, and can be completed with access to
channels params and mdev.
Adding the MTU to the channels params helps preserving that.
In addition, we save it in RQ to make its access faster in
datapath checks.
Saeed Mahameed [Wed, 14 Feb 2018 01:07:02 +0000 (17:07 -0800)]
net/mlx5: Eliminate query xsrq dead code
1. This function is not used anywhere in mlx5 driver
2. It has a memcpy statement that makes no sense and produces build
warning with gcc8
drivers/net/ethernet/mellanox/mlx5/core/transobj.c: In function 'mlx5_core_query_xsrq':
drivers/net/ethernet/mellanox/mlx5/core/transobj.c:347:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
Fixes: 01949d0109ee ("net/mlx5_core: Enable XRCs and SRQs when using ISSI > 0") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Lucas Bates [Thu, 29 Mar 2018 19:58:10 +0000 (15:58 -0400)]
tc-testing: Add newline when writing test case files
When using the -i feature to generate random ID numbers for test
cases in tdc, the function that writes the JSON to file doesn't
add a newline character to the end of the file, so we have to
add our own.
Signed-off-by: Lucas Bates <lucasb@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Thu, 29 Mar 2018 18:13:22 +0000 (11:13 -0700)]
liquidio: prevent rx queues from getting stalled
This commit has fix for RX traffic issues when we stress test the driver
with continuous ifconfig up/down under very high traffic conditions.
Reason for the issue is that, in existing liquidio_stop function NAPI is
disabled even before actual FW/HW interface is brought down via
send_rx_ctrl_cmd(lio, 0). Between time frame of NAPI disable and actual
interface down in firmware, firmware continuously enqueues rx traffic to
host. When interrupt happens for new packets, host irq handler fails in
scheduling NAPI as the NAPI is already disabled.
After "ifconfig <iface> up", Host re-enables NAPI but cannot schedule it
until it receives another Rx interrupt. Host never receives Rx interrupt as
it never cleared the Rx interrupt it received during interface down
operation. NIC Rx interrupt gets cleared only when Host processes queue and
clears the queue counts. Above anomaly leads to other issues like packet
overflow in FW/HW queues, backpressure.
Fix:
This commit fixes this issue by disabling NAPI only after informing
firmware to stop queueing packets to host via send_rx_ctrl_cmd(lio, 0).
send_rx_ctrl_cmd is not visible in the patch as it is already there in the
code. The DOWN command also waits for any pending packets to be processed
by NAPI so that the deadlock will not occur.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com> Acked-by: Derek Chickles <derek.chickles@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin fixed a unused variable in the new mcr20a driver.
Harry fixed an unitialised data read in the debugfs interface of the
ca8210 driver.
If there are any issues or you think these are to late for -rc1 (both can also
go into -rc2 as they are simple fixes) let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Biju Das [Thu, 29 Mar 2018 10:02:55 +0000 (11:02 +0100)]
dt-bindings: net: renesas-ravb: Add support for r8a77470 SoC
Add a new compatible string for the RZ/G1C (R8A77470) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Mar 2018 16:32:00 +0000 (12:32 -0400)]
Merge branch 'stmmac-DWMAC5'
Jose Abreu says:
====================
Fix TX Timeout and implement Safety Features
Fix the TX Timeout handler to correctly reconfigure the whole system and
start implementing features for DWMAC5 cores, specifically the Safety
Features.
Changes since v1:
- Display error stats in ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 29 Mar 2018 09:40:19 +0000 (10:40 +0100)]
net: stmmac: Add support for DWMAC5 and implement Safety Features
This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.
The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.
In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Thu, 29 Mar 2018 09:40:18 +0000 (10:40 +0100)]
net: stmmac: Rework and fix TX Timeout code
Currently TX Timeout handler does not behaves as expected and leads to
an unrecoverable state. Rework current implementation of TX Timeout
handling to actually perform a complete reset of the driver state and IP.
We use deferred work to init a task which will be responsible for
resetting the system.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Joao Pinto <jpinto@synopsys.com> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
do not allow adding routes if disable_ipv6 is enabled
Do not allow userspace to add static ipv6 routes if disable_ipv6 is enabled.
Update disable_ipv6 documentation according to that change
Changes since v1:
- added an extack message telling the user that IPv6 is disabled on the nexthop
device
- rebased on-top of net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Clarify that when disable_ipv6 is enabled even the ipv6 routes
are deleted for the selected interface and from now it will not
be possible to add addresses/routes to that interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. This batch comes with more input sanitization for xtables to
address bug reports from fuzzers, preparation works to the flowtable
infrastructure and assorted updates. In no particular order, they are:
1) Make sure userspace provides a valid standard target verdict, from
Florian Westphal.
2) Sanitize error target size, also from Florian.
3) Validate that last rule in basechain matches underflow/policy since
userspace assumes this when decoding the ruleset blob that comes
from the kernel, from Florian.
4) Consolidate hook entry checks through xt_check_table_hooks(),
patch from Florian.
5) Cap ruleset allocations at 512 mbytes, 134217728 rules and reject
very large compat offset arrays, so we have a reasonable upper limit
and fuzzers don't exercise the oom-killer. Patches from Florian.
6) Several WARN_ON checks on xtables mutex helper, from Florian.
7) xt_rateest now has a hashtable per net, from Cong Wang.
8) Consolidate counter allocation in xt_counters_alloc(), from Florian.
9) Earlier xt_table_unlock() call in {ip,ip6,arp,eb}tables, patch
from Xin Long.
10) Set FLOW_OFFLOAD_DIR_* to IP_CT_DIR_* definitions, patch from
Felix Fietkau.
11) Consolidate code through flow_offload_fill_dir(), also from Felix.
12) Inline ip6_dst_mtu_forward() just like ip_dst_mtu_maybe_forward()
to remove a dependency with flowtable and ipv6.ko, from Felix.
13) Cache mtu size in flow_offload_tuple object, this is safe for
forwarding as f87c10a8aa1e describes, from Felix.
14) Rename nf_flow_table.c to nf_flow_table_core.o, to simplify too
modular infrastructure, from Felix.
15) Add rt0, rt2 and rt4 IPv6 routing extension support, patch from
Ahmed Abdelsalam.
16) Remove unused parameter in nf_conncount_count(), from Yi-Hung Wei.
17) Support for counting only to nf_conncount infrastructure, patch
from Yi-Hung Wei.
18) Add strict NFT_CT_{SRC_IP,DST_IP,SRC_IP6,DST_IP6} key datatypes
to nft_ct.
19) Use boolean as return value from ipt_ah and from IPVS too, patch
from Gustavo A. R. Silva.
20) Remove useless parameters in nfnl_acct_overquota() and
nf_conntrack_broadcast_help(), from Taehee Yoo.
21) Use ipv6_addr_is_multicast() from xt_cluster, also from Taehee Yoo.
22) Statify nf_tables_obj_lookup_byhandle, patch from Fengguang Wu.
23) Fix typo in xt_limit, from Geert Uytterhoeven.
24) Do no use VLAs in Netfilter code, again from Gustavo.
25) Use ADD_COUNTER from ebtables, from Taehee Yoo.
26) Bitshift support for CONNMARK and MARK targets, from Jack Ma.
27) Use pr_*() and add pr_fmt(), from Arushi Singhal.
28) Add synproxy support to ctnetlink.
29) ICMP type and IGMP matching support for ebtables, patches from
Matthias Schiffer.
30) Support for the revision infrastructure to ebtables, from
Bernie Harris.
31) String match support for ebtables, also from Bernie.
32) Documentation for the new flowtable infrastructure.
33) Use generic comparison functions in ebt_stp, from Joe Perches.
34) Demodularize filter chains in nftables.
35) Register conntrack hooks in case nftables NAT chain is added.
36) Merge assignments with return in a couple of spots in the
Netfilter codebase, also from Arushi.
37) Document that xtables percpu counters are stored in the same
memory area, from Ben Hutchings.
38) Revert mark_source_chains() sanity checks that break existing
rulesets, from Florian Westphal.
39) Use is_zero_ether_addr() in the ipset codebase, from Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Close race between {un, }register_netdevice_notifier and pernet_operations
the problem is {,un}register_netdevice_notifier() do not take
pernet_ops_rwsem, and they don't see network namespaces, being
initialized in setup_net() and cleanup_net(), since at this
time net is not hashed to net_namespace_list.
This may lead to imbalance, when a notifier is called at time of
setup_net()/net is alive, but it's not called at time of cleanup_net(),
for the devices, hashed to the net, and vise versa. See (3/3) for
the scheme of imbalance.
This patchset fixes the problem by acquiring pernet_ops_rwsem
at the time of {,un}register_netdevice_notifier() (3/3).
(1-2/3) are preparations in xfrm and netfilter subsystems.
The problem was introduced a long ago, but backporting won't be easy,
since every previous kernel version may have changes in netdevice
notifiers, and they all need review and testing. Otherwise, there
may be more pernet_operations, which register or unregister
netdevice notifiers, and that leads to deadlock (which is was fixed
in 1-2/3). This patchset is for net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 14:03:45 +0000 (17:03 +0300)]
net: Close race between {un, }register_netdevice_notifier() and setup_net()/cleanup_net()
{un,}register_netdevice_notifier() iterate over all net namespaces
hashed to net_namespace_list. But pernet_operations register and
unregister netdevices in unhashed net namespace, and they are not
seen for netdevice notifiers. This results in asymmetry:
1)Race with register_netdevice_notifier()
pernet_operations::init(net) ...
register_netdevice() ...
call_netdevice_notifiers() ...
... nb is not called ...
... register_netdevice_notifier(nb) -> net skipped
... ...
list_add_tail(&net->list, ..) ...
Then, userspace stops using net, and it's destructed:
pernet_operations::exit(net)
unregister_netdevice()
call_netdevice_notifiers()
... nb is called ...
This always happens with net::loopback_dev, but it may be not the only device.
2)Race with unregister_netdevice_notifier()
pernet_operations::init(net)
register_netdevice()
call_netdevice_notifiers()
... nb is called ...
Then, userspace stops using net, and it's destructed:
list_del_rcu(&net->list) ...
pernet_operations::exit(net) unregister_netdevice_notifier(nb) -> net skipped
dev_change_net_namespace() ...
call_netdevice_notifiers()
... nb is not called ...
unregister_netdevice()
call_netdevice_notifiers()
... nb is not called ...
This race is more danger, since dev_change_net_namespace() moves real
network devices, which use not trivial netdevice notifiers, and if this
will happen, the system will be left in unpredictable state.
The patch closes the race. During the testing I found two places,
where register_netdevice_notifier() is called from pernet init/exit
methods (which led to deadlock) and fixed them (see previous patches).
The review moved me to one more unusual registration place:
raw_init() (can driver). It may be a reason of problems,
if someone creates in-kernel CAN_RAW sockets, since they
will be destroyed in exit method and raw_release()
will call unregister_netdevice_notifier(). But grep over
kernel tree does not show, someone creates such sockets
from kernel space.
Theoretically, there can be more places like this, and which are
hidden from review, but we found them on the first bumping there
(since there is no a race, it will be 100% reproducible).
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 14:03:35 +0000 (17:03 +0300)]
netfilter: Rework xt_TEE netdevice notifier
Register netdevice notifier for every iptable entry
is not good, since this breaks modularity, and
the hidden synchronization is based on rtnl_lock().
This patch reworks the synchronization via new lock,
while the rest of logic remains as it was before.
This is required for the next patch.
Tested via:
while :; do
unshare -n iptables -t mangle -A OUTPUT -j TEE --gateway 1.1.1.2 --oif lo;
done
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 14:03:25 +0000 (17:03 +0300)]
xfrm: Register xfrm_dev_notifier in appropriate place
Currently, driver registers it from pernet_operations::init method,
and this breaks modularity, because initialization of net namespace
and netdevice notifiers are orthogonal actions. We don't have
per-namespace netdevice notifiers; all of them are global for all
devices in all namespaces.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Posted this as a small set now, with an (optional) second patch that shows
how the changes work and what I've used to test the code on a Topic Miami board.
I've taken the liberty to add appropriate "Acked" and "Review" tags.
v4: Replaced "6" with ETH_ALEN
v3: Add patch that implements mac in nvmem for the Cadence MACB controller
Remove the integrated of_get_mac_address call
v2: Use of_nvmem_cell_get to avoid needing the assiciated device
Use void* instead of char*
Add devicetree binding doc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Looijmans [Thu, 29 Mar 2018 05:29:49 +0000 (07:29 +0200)]
net: macb: Try to retrieve MAC addess from nvmem provider
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mike Looijmans [Thu, 29 Mar 2018 05:29:48 +0000 (07:29 +0200)]
of_net: Implement of_get_nvmem_mac_address helper
It's common practice to store MAC addresses for network interfaces into
nvmem devices. However the code to actually do this in the kernel lacks,
so this patch adds of_get_nvmem_mac_address() for drivers to obtain the
address from an nvmem cell provider.
This is particulary useful on devices where the ethernet interface cannot
be configured by the bootloader, for example because it's in an FPGA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Mar 2018 14:18:55 +0000 (10:18 -0400)]
Merge branch 'nfp-flower-handle-MTU-changes'
Jakub Kicinski says:
====================
nfp: flower: handle MTU changes
This set improves MTU handling for flower offload. The max MTU is
correctly capped and physical port MTU is communicated to the FW
(and indirectly HW).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 29 Mar 2018 01:50:07 +0000 (18:50 -0700)]
nfp: flower: offload phys port MTU change
Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.
Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.
Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.
Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Thu, 29 Mar 2018 01:50:06 +0000 (18:50 -0700)]
nfp: modify app MTU setting callbacks
Rename the 'change_mtu' app callback to 'check_mtu'. This is called
whenever an MTU change is requested on a netdev. It can reject the
change but is not responsible for implementing it.
Introduce a new 'repr_change_mtu' app callback that is hit when the MTU
of a repr is to be changed. This is responsible for performing the MTU
change and verifying it.
Signed-off-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Mar 2018 14:11:07 +0000 (10:11 -0400)]
Merge branch 'phylink-API-changes'
Florian Fainelli says:
====================
phylink: API changes
This patch series contains two API changes to PHYLINK which will later be used
by DSA to migrate to PHYLINK. Because these are API changes that impact other
outstanding work (e.g: MVPP2) I would rather get them included sooner to minimize
conflicts.
Thank you!
Changes in v2:
- added missing documentation to mac_link_{up,down} that the interface
must be configured in mac_config()
- added Russell's, Andrew's and my tags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 28 Mar 2018 22:44:16 +0000 (15:44 -0700)]
sfp/phylink: move module EEPROM ethtool access into netdev core ethtool
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Mar 2018 22:44:15 +0000 (15:44 -0700)]
net: phy: phylink: Provide PHY interface to mac_link_{up, down}
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ronak Doshi [Wed, 28 Mar 2018 22:38:19 +0000 (15:38 -0700)]
MAINTAINERS: update vmxnet3 driver maintainer
Shrikrishna Khare would no longer maintain the vmxnet3 driver. Taking
over the role of vmxnet3 maintainer.
Signed-off-by: Ronak Doshi <doshir@vmware.com> Signed-off-by: Shrikrishna Khare <skhare@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Following Tal's review of the adaptive RX/TX coalescing feature added to the
SYSTEMPORT and GENET driver a number of things showed up:
- adaptive TX coalescing is not actually a good idea with the current way
the estimator will program the ring, this results in a higher CPU load, NAPI
on TX already does a reasonably good job at maintaining the interrupt count low
- both SYSTEMPORT and GENET would suffer from the same issues while configuring
coalescing parameters where the values would just not be applied correctly
based on user settings, so we fix that too
Tal, thanks again for your feedback, I would appreciate if you could review that
the new behavior appears to be implemented correctly.
Thanks!
Changes in v2:
- added Tal's reviewed-by to the first patch
- split DIM initialization from coalescing parameters initialization
- avoid duplicating the same code in bcmgenet_set_coalesce() when configuring RX rings
- fixed the condition where default DIM parameters would be applied when
adaptive RX coalescing would be enabled, do this only if it was disabled before
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Mar 2018 22:15:38 +0000 (15:15 -0700)]
net: bcmgenet: Fix coalescing settings handling
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827a2 ("net: bcmgenet: Add support for adaptive RX coalescing") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Mar 2018 22:15:37 +0000 (15:15 -0700)]
net: systemport: Fix coalescing settings handling
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e875421e ("net: systemport: Implement adaptive interrupt coalescing") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 28 Mar 2018 22:15:36 +0000 (15:15 -0700)]
net: systemport: Remove adaptive TX coalescing
Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: Tal Gilboa <talgi@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Wed, 28 Mar 2018 14:46:54 +0000 (17:46 +0300)]
net: Call add/kill vid ndo on vlan filter feature toggling
NETIF_F_HW_VLAN_[CS]TAG_FILTER features require more than just a bit
flip in dev->features in order to keep the driver in a consistent state.
These features notify the driver of each added/removed vlan, but toggling
of vlan-filter does not notify the driver accordingly for each of the
existing vlans.
This patch implements a similar solution to NETIF_F_RX_UDP_TUNNEL_PORT
behavior (which notifies the driver about UDP ports in the same manner
that vids are reported).
Each toggling of the features propagates to the 8021q module, which
iterates over the vlans and call add/kill ndo accordingly.
Signed-off-by: Gal Pressman <galp@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 28 Mar 2018 12:51:09 +0000 (12:51 +0000)]
cxgb4: fix error return code in adap_init0()
Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.
Fixes: 5c31254e35a8 ("cxgb4: initialize hash-filter configuration") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Valdis Kletnieks reported that xtables is broken in linux-next since 0d7df906a0e78 ("netfilter: x_tables: ensure last rule in base chain
matches underflow/policy"), as kernel rejects the (well-formed) ruleset:
[ 64.402790] ip6_tables: last base chain position 1136 doesn't match underflow 1344 (hook 1)
mark_source_chains is not the correct place for such a check, as it
terminates evaluation of a chain once it sees an unconditional verdict
(following rules are known to be unreachable). It seems preferrable to
fix libiptc instead, so remove this check again.
Fixes: 0d7df906a0e78 ("netfilter: x_tables: ensure last rule in base chain matches underflow/policy") Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ben Hutchings [Thu, 29 Mar 2018 14:12:41 +0000 (15:12 +0100)]
netfilter: x_tables: Add note about how to free percpu counters
Due to the way percpu counters are allocated and freed in blocks,
it is not safe to free counters individually. Currently all callers
do the right thing, but let's note this restriction.
Fixes: ae0ac0ed6fcf ("netfilter: x_tables: pack percpu counter allocations") Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: enable conntrack if NAT chain is registered
Register conntrack hooks if the user adds NAT chains. Users get confused
with the existing behaviour since they will see no packets hitting this
chain until they add the first rule that refers to conntrack.
This patch adds new ->init() and ->free() indirections to chain types
that can be used by NAT chains to invoke the conntrack dependency.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
One module per supported filter chain family type takes too much memory
for very little code - too much modularization - place all chain filter
definitions in one single file.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use WARN_ON() instead since it should not happen that neither family
goes over NFPROTO_NUMPROTO nor there is already a chain of this type
already registered.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use nft_ prefix. By when I added chain types, I forgot to use the
nftables prefix. Rename enum nft_chain_type to enum nft_chain_types too,
otherwise there is an overlap.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bernie Harris [Wed, 21 Mar 2018 02:42:16 +0000 (15:42 +1300)]
netfilter: ebtables: Add string filter
This patch is part of a proposal to add a string filter to
ebtables, which would be similar to the string filter in
iptables. Like iptables, the ebtables filter uses the xt_string
module.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bernie Harris [Wed, 21 Mar 2018 02:42:15 +0000 (15:42 +1300)]
netfilter: ebtables: Add support for specifying match revision
Currently ebtables assumes that the revision number of all match
modules is 0, which is an issue when trying to use existing
xtables matches with ebtables. The solution is to modify ebtables
to allow extensions to specify a revision number, similar to
iptables. This gets passed down to the kernel, which is then able
to find the match module correctly.
To main binary backwards compatibility, the size of the ebt_entry
structures is not changed, only the size of the name field is
decreased by 1 byte to make room for the revision field.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller [Thu, 29 Mar 2018 20:23:26 +0000 (16:23 -0400)]
Merge tag 'mac80211-next-for-davem-2018-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Mar 2018 19:04:22 +0000 (15:04 -0400)]
Merge branch 'dsa-Add-ATU-VTU-statistics'
Andrew Lunn says:
====================
Add ATU/VTU statistics
Previous patches have added basic support for Address Translation Unit
and VLAN translation Unit violation interrupts. Add statistics
counters for when these occur, which can be accessed using
ethtool. Downgrade one of the particularly spammy warnings from VTU
violations to debug only, now that we have a counter for it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 28 Mar 2018 21:50:29 +0000 (23:50 +0200)]
net: dsa: mv88e6xxx: Make VTU miss violations less spammy
VTU miss violations can happen under normal conditions. Don't spam the
kernel log, downgrade the output to debug level only. The statistics
counter will indicate it is happening, if anybody not debugging is
interested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reported-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 28 Mar 2018 14:14:56 +0000 (16:14 +0200)]
sctp: fix unused lable warning
The proc file cleanup left a label possibly unused:
net/sctp/protocol.c: In function 'sctp_defaults_init':
net/sctp/protocol.c:1304:1: error: label 'err_init_proc' defined but not used [-Werror=unused-label]
This adds an #ifdef around it to match the respective 'goto'.
Fixes: d47d08c8ca05 ("sctp: use proc_remove_subtree()") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Yongjun [Wed, 28 Mar 2018 12:51:19 +0000 (12:51 +0000)]
net: bcmgenet: return NULL instead of plain integer
Fixes the following sparse warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1351:16: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 28 Mar 2018 11:48:36 +0000 (14:48 +0300)]
test_bpf: Fix NULL vs IS_ERR() check in test_skb_segment()
The skb_segment() function returns error pointers on error. It never
returns NULL.
Fixes: 76db8087c4c9 ("net: bpf: add a test for skb_segment in test_bpf module") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Yonghong Song <yhs@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Wed, 28 Mar 2018 10:18:25 +0000 (11:18 +0100)]
sfp: allow cotsworks modules
Cotsworks modules fail the checksums - it appears that Cotsworks
reprograms the EEPROM at the end of production with the final product
information (serial, date code, and exact part number for module
options) and fails to update the checksum.
Work around this by detecting the Cotsworks name in the manufacturer
field, and reducing the checksum failures to warnings rather than a
hard error.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ethtool callback implementation for flash update.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Fix PTT entry leak in the selftest error flow.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for populating the flash image attributes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com> Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Acked-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha [Wed, 28 Mar 2018 02:25:18 +0000 (19:25 -0700)]
liquidio: Prioritize control messages
During heavy tx traffic, control messages (sent by liquidio driver to NIC
firmware) sometimes do not get processed in a timely manner. Reason is:
the low-level metadata of control messages and that of egress network
packets indicate that they have the same priority.
Fix it by setting a higher priority for control messages through the new
ctrl_qpg field in the oct_txpciq struct. It is the NIC firmware that does
the actual setting of priority by writing to the new ctrl_qpg field; the
host driver treats that value as opaque and just assigns it to pki_ih3->qpg
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com> Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: Allow FIB notifiers to fail add and replace
I wanted to revisit how resource overload is handled for hardware offload
of FIB entries and rules. At the moment, the in-kernel fib notifier can
tell a driver about a route or rule add, replace, and delete, but the
notifier can not affect the action. Specifically, in the case of mlxsw
if a route or rule add is going to overflow the ASIC resources the only
recourse is to abort hardware offload. Aborting offload is akin to taking
down the switch as the path from data plane to the control plane simply
can not support the traffic bandwidth of the front panel ports. Further,
the current state of FIB notifiers is inconsistent with other resources
where a driver can affect a user request - e.g., enslavement of a port
into a bridge or a VRF.
As a result of the work done over the past 3+ years, I believe we are
at a point where we can bring consistency to the stack and offloads,
and reliably allow the FIB notifiers to fail a request, pushing an error
along with a suitable error message back to the user. Rather than
aborting offload when the switch is out of resources, userspace is simply
prevented from adding more routes and has a clear indication of why.
This set does not resolve the corner case where rules or routes not
supported by the device are installed prior to the driver getting loaded
and registering for FIB notifications. In that case, hardware offload has
not been established and it can refuse to offload anything, sending
errors back to userspace via extack. Since conceptually the driver owns
the netdevices associated with its asic, this corner case mainly applies
to unsupported rules and any races during the bringup phase.
Patch 1 fixes call_fib_notifiers to extract the errno from the encoded
response from handlers.
Patches 2-5 allow the call to call_fib_notifiers to fail the add or
replace of a route or rule.
Patch 6 adds a simple resource controller to netdevsim to illustrate
how a FIB resource controller can limit the number of route entries.
Changes since RFC
- correct return code for call_fib_notifier
- dropped patch 6 exporting devlink symbols
- limited example resource controller to init_net only
- updated Kconfig for netdevsim to use MAY_USE_DEVLINK
- updated cover letter regarding startup case noted by Ido
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:22:00 +0000 (18:22 -0700)]
netdevsim: Add simple FIB resource controller via devlink
Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.
The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
/IPv4
/IPv4/fib
/IPv4/fib-rules
/IPv6
/IPv6/fib
/IPv6/fib-rules
The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
$ devlink dev reload netdevsim/netdevsim0
such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
$ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
Error: netdevsim: Exceeded number of supported fib entries.
$ devlink resource show netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
resources:
name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
...
With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.
Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:21:59 +0000 (18:21 -0700)]
net/ipv6: Move call_fib6_entry_notifiers up for route adds
Move call to call_fib6_entry_notifiers for new IPv6 routes to right
before the insertion into the FIB. At this point notifier handlers can
decide the fate of the new route with a clean path to delete the
potential new entry if the notifier returns non-0.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:21:58 +0000 (18:21 -0700)]
net/ipv4: Allow notifier to fail route replace
Add checking to call to call_fib_entry_notifiers for IPv4 route replace.
Allows a notifier handler to fail the replace.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:21:57 +0000 (18:21 -0700)]
net/ipv4: Move call_fib_entry_notifiers up for new routes
Move call to call_fib_entry_notifiers for new IPv4 routes to right
before the call to fib_insert_alias. At this point the only remaining
failure path is memory allocations in fib_insert_node. Handle that
very unlikely failure with a call to call_fib_entry_notifiers to
tell drivers about it.
At this point notifier handlers can decide the fate of the new route
with a clean path to delete the potential new entry if the notifier
returns non-0.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:21:56 +0000 (18:21 -0700)]
net: Move call_fib_rule_notifiers up in fib_nl_newrule
Move call_fib_rule_notifiers up in fib_nl_newrule to the point right
before the rule is inserted into the list. At this point there are no
more failure paths within the core rule code, so if the notifier
does not fail then the rule will be inserted into the list.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 28 Mar 2018 01:21:55 +0000 (18:21 -0700)]
net: Fix fib notifer to return errno
Notifier handlers use notifier_from_errno to convert any potential error
to an encoded format. As a consequence the other side, call_fib_notifier{s}
in this case, needs to use notifier_to_errno to return the error from
the handler back to its caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Introduce net_rwsem to protect net_namespace_list
The series introduces fine grained rw_semaphore, which will be used
instead of rtnl_lock() to protect net_namespace_list.
This improves scalability and allows to do non-exclusive sleepable
iteration for_each_net(), which is enough for most cases.
scripts/get_maintainer.pl gives enormous list of people, and I add
all to CC.
Note, that this patch is independent of "Close race between
{un, }register_netdevice_notifier and pernet_operations":
https://patchwork.ozlabs.org/project/netdev/list/?series=36495
Kirill Tkhai [Thu, 29 Mar 2018 16:21:09 +0000 (19:21 +0300)]
ovs: Remove rtnl_lock() from ovs_exit_net()
Here we iterate for_each_net() and removes
vport from alive net to the exiting net.
ovs_net::dps are protected by ovs_mutex(),
and the others, who change it (ovs_dp_cmd_new(),
__dp_destroy()) also take it.
The same with datapath::ports list.
So, we remove rtnl_lock() here.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 16:20:56 +0000 (19:20 +0300)]
security: Remove rtnl_lock() in selinux_xfrm_notify_policyload()
rt_genid_bump_all() consists of ipv4 and ipv6 part.
ipv4 part is incrementing of net::ipv4::rt_genid,
and I see many places, where it's read without rtnl_lock().
ipv6 part calls __fib6_clean_all(), and it's also
called without rtnl_lock() in other places.
So, rtnl_lock() here was used to iterate net_namespace_list only,
and we can remove it.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 16:20:44 +0000 (19:20 +0300)]
net: Don't take rtnl_lock() in wireless_nlevent_flush()
This function iterates over net_namespace_list and flushes
the queue for every of them. What does this rtnl_lock()
protects?! Since we may add skbs to net::wext_nlevents
without rtnl_lock(), it does not protects us about queuers.
It guarantees, two threads can't flush the queue in parallel,
that can change the order, but since skb can be queued
in any order, it doesn't matter, how many threads do this
in parallel. In case of several threads, this will be even
faster.
So, we can remove rtnl_lock() here, as it was used for
iteration over net_namespace_list only.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kirill Tkhai [Thu, 29 Mar 2018 16:20:32 +0000 (19:20 +0300)]
net: Introduce net_rwsem to protect net_namespace_list
rtnl_lock() is used everywhere, and contention is very high.
When someone wants to iterate over alive net namespaces,
he/she has no a possibility to do that without exclusive lock.
But the exclusive rtnl_lock() in such places is overkill,
and it just increases the contention. Yes, there is already
for_each_net_rcu() in kernel, but it requires rcu_read_lock(),
and this can't be sleepable. Also, sometimes it may be need
really prevent net_namespace_list growth, so for_each_net_rcu()
is not fit there.
This patch introduces new rw_semaphore, which will be used
instead of rtnl_mutex to protect net_namespace_list. It is
sleepable and allows not-exclusive iterations over net
namespaces list. It allows to stop using rtnl_lock()
in several places (what is made in next patches) and makes
less the time, we keep rtnl_mutex. Here we just add new lock,
while the explanation of we can remove rtnl_lock() there are
in next patches.
Fine grained locks generally are better, then one big lock,
so let's do that with net_namespace_list, while the situation
allows that.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: bgmac: Couple of small bgmac changes
This patch series addresses two minor issues with the bgmac driver:
- provides the interface name through /proc/interrupts rather than "bgmac"
- makes sure the interrupts are masked during probe, in case the block was
not properly reset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 27 Mar 2018 23:20:02 +0000 (16:20 -0700)]
net: bgmac: Mask interrupts during probe
We can have interrupts left enabled form e.g: the bootloader which used
the network device for network boot. Make sure we have those disabled as
early as possible to avoid spurious interrupts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 27 Mar 2018 23:20:01 +0000 (16:20 -0700)]
net: bgmac: Use interface name to request interrupt
When the system contains several BGMAC adapters, it is nice to be able
to tell which one is which by looking at /proc/interrupts. Use the
network device name as a name to request_irq() with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Mar 2018 16:02:08 +0000 (12:02 -0400)]
Merge tag 'rxrpc-next-20180327' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Tracing updates
Here are some patches that update tracing in AF_RXRPC and AFS:
(1) Add a tracepoint for tracking resend events.
(2) Use debug_ids in traces rather than pointers (as pointers are now hashed)
and allow use of the same debug_id in AFS calls as in the corresponding
AF_RXRPC calls. This makes filtering the trace output much easier.
(3) Add a tracepoint for tracking call completion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Harry Morris [Wed, 28 Mar 2018 10:54:27 +0000 (11:54 +0100)]
ieee802154: ca8210: fix uninitialised data read
In ca8210_test_int_user_write() a user can request the transfer of a
frame with a length field (command.length) that is longer than the
actual buffer provided (len). In this scenario the driver will copy
the buffer contents into the uninitialised command[] buffer, then
transfer <data.length> bytes over the SPI even though only <len> bytes
had been populated, potentially leaking sensitive kernel memory.
Also the first 6 bytes of the command buffer must be initialised in case
a malformed, short packet is written and the uninitialised bytes are
read in ca8210_test_check_upstream.
Reported-by: Domen Puncer Kugler <domen.puncer@samsung.com> Signed-off-by: Harry Morris <h.morris@cascoda.com> Tested-by: Harry Morris <h.morris@cascoda.com> Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
projects / linux.git / log