Kailang Yang [Thu, 21 Feb 2019 08:10:22 +0000 (16:10 +0800)]
ALSA: hda/realtek - Fixed Headset Mic JD not stable
It will be lose Mic JD state when Chrome OS boot and headset was plugged.
Implement of reset combo jack JD. It will show normally.
Fixes: e854747d7593 ("ALSA: hda/realtek - Enable headset button support for new codec") Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jian-Hong Pan [Wed, 13 Mar 2019 09:33:24 +0000 (17:33 +0800)]
ALSA: hda/realtek: Enable headset MIC of Acer TravelMate X514-51T with ALC255
The Acer TravelMate X514-51T with ALC255 cannot detect the headset MIC
until ALC255_FIXUP_ACER_HEADSET_MIC quirk applied. Although, the
internal DMIC uses another module - snd_soc_skl as the driver. We still
need the NID 0x1a in the quirk to enable the headset MIC.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Arnd Bergmann [Mon, 4 Mar 2019 20:33:25 +0000 (21:33 +0100)]
ALSA: hda/tegra: avoid build error without CONFIG_PM
The #ifdef protection around the PM functions is wrong, leading to
a failed reference in some configurations:
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_runtime_suspend':
sound/pci/hda/hda_tegra.c:273:2: error: implicit declaration of function 'hda_tegra_disable_clocks'; did you mean 'hda_tegra_enable_clocks'? [-Werror=implicit-function-declaration]
Better remove the #ifdefs entirely and rely on the compiler silently
dropping unused functions marked __maybe_unused.
usb_alloc_urb() can fail due to kmalloc failure and push the error
upstream. Further this can cause a NULL pointer dereference in
init_pipe_urbs(). This patch avoids such a scenario.
Mariusz Ceier [Mon, 11 Mar 2019 20:53:57 +0000 (21:53 +0100)]
ALSA: hda: Avoid NULL pointer dereference at snd_hdac_stream_start()
For ca0132 codec, azx_dev->stream is NULL during firmware loading.
Calling snd_hdac_get_stream_stripe_ctl unconditionally causes NULL
pointer dereference in that function.
Fixes: 9b6f7e7a296e ("ALSA: hda: program stripe bits for controller") Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Manuel Reinhardt [Thu, 28 Feb 2019 19:34:04 +0000 (20:34 +0100)]
ALSA: usb-audio: Add quirk for MOTU MicroBook II
Add an entry to the quirks-table to for usb-audio to recognize the
Microbook II (although it only exposes vendor interfaces). A simple boot
quirk is also implemented to set up the sample rate and make sure that
no audio urbs are sent before the device is ready.
This patch only provides audio playback and capture at 96kHz sample
rate. Notice the following shortcomings:
- The sample rate is currently hardcoded to 96k although the device also
supports 48k and 44.1k.
- The various mixer controls of the MicroBook are not made available.
- The keep-iface control should be on by default because the device
shuts down whenever the altsetting is reset which is usually unwanted.
(I don't know the best way to do this)
- The communication format used by the MicroBook for sample rate setting
and also other setup has been reverse engineered by looking at the
usbmon output while running the windows driver through virtualbox. In
this patch the first byte of every message is set to \0 while in the
observed communications the first byte acts as a "message-counter"
increasing its value with every message sent. Leaving it at \0 does
not seem to affect the device.
Signed-off-by: Manuel Reinhardt <manuel.rhdt@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Thu, 28 Feb 2019 12:30:55 +0000 (13:30 +0100)]
Merge tag 'asoc-v5.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More changes for v5.1
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
Olivier Moysan [Tue, 26 Feb 2019 13:51:04 +0000 (14:51 +0100)]
ASoC: stm32: i2s: fix IRQ clearing
Because of regmap cache, interrupts may not be cleared
as expected.
Declare IFCR register as write only and make writings
to IFCR register unconditional.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jenny TC [Mon, 25 Feb 2019 16:47:31 +0000 (22:17 +0530)]
ASoC: Intel: Boards: Add Maxim98373 support
This patch enables the reuse of kbl_da7219_max98927 machine driver to
support max98373. The same machine driver is modified for cases where one
amplifier is swapped out with another. Most of the changes are about
renaming the codec and codec_dai names, with minor differences due to
support for 24 bits in one case and 16 in the other.
Signed-off-by: Jenny TC <jenny.tc@intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Jiada Wang [Mon, 25 Feb 2019 11:14:20 +0000 (12:14 +0100)]
ASoC: rsnd: gen: fix SSI9 4/5/6/7 busif related register address
Currently each SSI unit 's busif mode/adinr/dalign address is
registered by: (in busif4 case)
RSND_GEN_M_REG(SSI_BUSIF4_MODE, 0x500, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_ADINR,0x504, 0x80)
RSND_GEN_M_REG(SSI_BUSIF4_DALIGN, 0x508, 0x80)
But according to user manual 41.1.4 Register Configuration
ssi9 4/5/6/7 busif mode/adinr/dalign register address
( SSI9-[4/5/6/7]_BUSIF_[MODE/ADINR/DALIGN] )
are out of this rule.
This patch registers ssi9 4/5/6/7 mode/adinr/dalign register
as single register, and access these registers in case of
SSI9 BUSIF 4/5/6/7.
Fixes: commit 8c9d75033340 ("ASoC: rsnd: ssiu: Support BUSIF other than BUSIF0") Signed-off-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Timo Wischer <twischer@de.adit-jv.com> Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Takashi Sakamoto [Tue, 26 Feb 2019 04:38:37 +0000 (13:38 +0900)]
ALSA: firewire-motu: fix construction of PCM frame for capture direction
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
Takashi Sakamoto [Tue, 26 Feb 2019 04:38:16 +0000 (13:38 +0900)]
ALSA: bebob: use more identical mod_alias for Saffire Pro 10 I/O against Liquid Saffire 56
ALSA bebob driver has an entry for Focusrite Saffire Pro 10 I/O. The
entry matches vendor_id in root directory and model_id in unit
directory of configuration ROM for IEEE 1394 bus.
On the other hand, configuration ROM of Focusrite Liquid Saffire 56
has the same vendor_id and model_id. This device is an application of
TCAT Dice (TCD2220 a.k.a Dice Jr.) however ALSA bebob driver can be
bound to it randomly instead of ALSA dice driver. At present, drivers
in ALSA firewire stack can not handle this situation appropriately.
This commit uses more identical mod_alias for Focusrite Saffire Pro 10
I/O in ALSA bebob driver.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 042a829d bus_info_length 4, crc_length 42, crc 33437
404 31333934 bus_name "1394"
408 f0649222 irmc 1, cmc 1, isc 1, bmc 1, pmc 0, cyc_clk_acc 100,
max_rec 9 (1024), max_rom 2, gen 2, spd 2 (S400)
40c 00130e01 company_id 00130e |
410 000606e0 device_id 01000606e0 | EUI-64 00130e01000606e0
root directory
-----------------------------------------------------------------
414 0009d31c directory_length 9, crc 54044
418 04000014 hardware version
41c 0c0083c0 node capabilities per IEEE 1394
420 0300130e vendor
424 81000012 --> descriptor leaf at 46c
428 17000006 model
42c 81000016 --> descriptor leaf at 484
430 130120c2 version
434 d1000002 --> unit directory at 43c
438 d4000006 --> dependent info directory at 450
unit directory at 43c
-----------------------------------------------------------------
43c 0004707c directory_length 4, crc 28796
440 1200a02d specifier id: 1394 TA
444 13010001 version: AV/C
448 17000006 model
44c 81000013 --> descriptor leaf at 498
dependent info directory at 450
-----------------------------------------------------------------
450 000637c7 directory_length 6, crc 14279
454 120007f5 specifier id
458 13000001 version
45c 3affffc7 (immediate value)
460 3b100000 (immediate value)
464 3cffffc7 (immediate value)
468 3d600000 (immediate value)
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 040442e4 bus_info_length 4, crc_length 4, crc 17124
404 31333934 bus_name "1394"
408 e0ff8112 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c 00130e04 company_id 00130e |
410 018001e9 device_id 04018001e9 | EUI-64 00130e04018001e9
root directory
-----------------------------------------------------------------
414 00065612 directory_length 6, crc 22034
418 0300130e vendor
41c 8100000a --> descriptor leaf at 444
420 17000006 model
424 8100000e --> descriptor leaf at 45c
428 0c0087c0 node capabilities per IEEE 1394
42c d1000001 --> unit directory at 430
unit directory at 430
-----------------------------------------------------------------
430 000418a0 directory_length 4, crc 6304
434 1200130e specifier id
438 13000001 version
43c 17000006 model
440 8100000f --> descriptor leaf at 47c
Takashi Iwai [Mon, 25 Feb 2019 15:49:27 +0000 (16:49 +0100)]
ALSA: hda: Extend i915 component bind timeout
I set 10 seconds for the timeout of the i915 audio component binding
with a hope that recent machines are fast enough to handle all probe
tasks in that period, but I was too optimistic. The binding may take
longer than that, and this caused a problem on the machine with both
audio and graphics driver modules loaded in parallel, as Paul Menzel
experienced. This problem haven't hit so often just because the KMS
driver is loaded in initrd on most machines.
As a simple workaround, extend the timeout to 60 seconds.
Linus Torvalds [Sun, 24 Feb 2019 17:47:07 +0000 (09:47 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
kvm: x86: Return LA57 feature based on hardware capability
x86/kvm/mmu: fix switch between root and guest MMUs
s390: vsie: Use effective CRYCBD.31 to check CRYCBD validity
Pull networking fixes from David Miller:
"Hopefully the last pull request for this release. Fingers crossed:
1) Only refcount ESP stats on full sockets, from Martin Willi.
2) Missing barriers in AF_UNIX, from Al Viro.
3) RCU protection fixes in ipv6 route code, from Paolo Abeni.
4) Avoid false positives in untrusted GSO validation, from Willem de
Bruijn.
5) Forwarded mesh packets in mac80211 need more tailroom allocated,
from Felix Fietkau.
6) Use operstate consistently for linkup in team driver, from George
Wilkie.
7) ThunderX bug fixes from Vadim Lomovtsev. Mostly races between VF
and PF code paths.
8) Purge ipv6 exceptions during netdevice removal, from Paolo Abeni.
9) nfp eBPF code gen fixes from Jiong Wang.
10) bnxt_en firmware timeout fix from Michael Chan.
11) Use after free in udp/udpv6 error handlers, from Paolo Abeni.
12) Fix a race in x25_bind triggerable by syzbot, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
net: phy: realtek: Dummy IRQ calls for RTL8366RB
tcp: repaired skbs must init their tso_segs
net/x25: fix a race in x25_bind()
net: dsa: Remove documentation for port_fdb_prepare
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
selftests: fib_tests: sleep after changing carrier. again.
net: set static variable an initial value in atl2_probe()
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
bpf, doc: add bpf list as secondary entry to maintainers file
udp: fix possible user after free in error handler
udpv6: fix possible user after free in error handler
fou6: fix proto error handler argument type
udpv6: add the required annotation to mib type
mdio_bus: Fix use-after-free on device_register fails
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
bnxt_en: Wait longer for the firmware message response to complete.
bnxt_en: Fix typo in firmware message timeout logic.
nfp: bpf: fix ALU32 high bits clearance bug
nfp: bpf: fix code-gen bug on BPF_ALU | BPF_XOR | BPF_K
Documentation: networking: switchdev: Update port parent ID section
...
Linus Walleij [Sun, 24 Feb 2019 00:11:15 +0000 (01:11 +0100)]
net: phy: realtek: Dummy IRQ calls for RTL8366RB
This fixes a regression introduced by
commit 0d2e778e38e0ddffab4bb2b0e9ed2ad5165c4bf7
"net: phy: replace PHY_HAS_INTERRUPT with a check for
config_intr and ack_interrupt".
This assumes that a PHY cannot trigger interrupt unless
it has .config_intr() or .ack_interrupt() implemented.
A later patch makes the code assume both need to be
implemented for interrupts to be present.
But this PHY (which is inside a DSA) will happily
fire interrupts without either callback.
Implement dummy callbacks for .config_intr() and
.ack_interrupt() in the phy header to fix this.
Tested on the RTL8366RB on D-Link DIR-685.
Fixes: 0d2e778e38e0 ("net: phy: replace PHY_HAS_INTERRUPT with a check for config_intr and ack_interrupt") Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 23 Feb 2019 21:24:59 +0000 (13:24 -0800)]
net/x25: fix a race in x25_bind()
syzbot was able to trigger another soft lockup [1]
I first thought it was the O(N^2) issue I mentioned in my
prior fix (f657d22ee1f "net/x25: do not hold the cpu
too long in x25_new_lci()"), but I eventually found
that x25_bind() was not checking SOCK_ZAPPED state under
socket lock protection.
This means that multiple threads can end up calling
x25_insert_socket() for the same socket, and corrupt x25_list
Fixes: 90c27297a9bf ("X.25 remove bkl in bind") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Hangbin Liu [Fri, 22 Feb 2019 13:22:32 +0000 (21:22 +0800)]
Revert "bridge: do not add port to router list when receives query with source 0.0.0.0"
This reverts commit 5a2de63fd1a5 ("bridge: do not add port to router list
when receives query with source 0.0.0.0") and commit 0fe5119e267f ("net:
bridge: remove ipv6 zero address check in mcast queries")
The reason is RFC 4541 is not a standard but suggestive. Currently we
will elect 0.0.0.0 as Querier if there is no ip address configured on
bridge. If we do not add the port which recives query with source
0.0.0.0 to router list, the IGMP reports will not be about to forward
to Querier, IGMP data will also not be able to forward to dest.
As Nikolay suggested, revert this change first and add a boolopt api
to disable none-zero election in future if needed.
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Reported-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0") Fixes: 0fe5119e267f ("net: bridge: remove ipv6 zero address check in mcast queries") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
selftests: fib_tests: sleep after changing carrier. again.
Just like commit e2ba732a1681 ("selftests: fib_tests: sleep after
changing carrier"), wait one second to allow linkwatch to propagate the
carrier change to the stack.
There are two sets of carrier tests. The first slept after the carrier
was set to off, and when the second set ran, it was likely that the
linkwatch would be able to run again without much delay, reducing the
likelihood of a race. However, if you run 'fib_tests.sh -t carrier' on a
loop, you will quickly notice the failures.
Sleeping on the second set of tests make the failures go away.
Cc: David Ahern <dsahern@gmail.com> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Mao Wenan [Fri, 22 Feb 2019 06:57:23 +0000 (14:57 +0800)]
net: set static variable an initial value in atl2_probe()
cards_found is a static variable, but when it enters atl2_probe(),
cards_found is set to zero, the value is not consistent with last probe,
so next behavior is not our expect.
Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell10g: Fix Multi-G advertisement to only advertise 10G
Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff3f ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reported-by: Russell King <linux@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 17:48:01 +0000 (09:48 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a bug in BPF's LPM deletion logic to match correct prefix
length, from Alban.
2) Fix AF_XDP teardown by not destroying umem prematurely as it
is still needed till all outstanding skbs are freed, from Björn.
3) Fix unkillable BPF_PROG_TEST_RUN under preempt kernel by checking
signal_pending() outside need_resched() condition which is never
triggered there, from Stanislav.
4) Fix two nfp JIT bugs, one in code emission for K-based xor, and
another one to explicitly clear upper bits in alu32, from Jiong.
5) Add bpf list address to maintainers file, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 23 Feb 2019 01:46:30 +0000 (17:46 -0800)]
Merge tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix a regression in the PM-runtime framework introduced by the
recent switch-over of it to using hrtimers and a use-after-free
introduced by one of the recent changes in the scmi-cpufreq driver.
Specifics:
- Use hrtimer_try_to_cancel() instead of hrtimer_cancel() in the
PM-runtime framework to avoid a possible timer-related deadlock
introduced recently (Vincent Guittot).
- Reorder the scmi-cpufreq driver code to avoid accessing memory that
has just been freed (Yangtao Li)"
* tag 'pm-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM-runtime: Fix deadlock when canceling hrtimer
cpufreq: scmi: Fix use-after-free in scmi_cpufreq_exit()
Linus Torvalds [Sat, 23 Feb 2019 00:31:26 +0000 (16:31 -0800)]
Merge tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Fixes for ARC for 5.0, bunch of those are stable fodder anyways so
sooner the better.
- Fix memcpy to prevent prefetchw beyond end of buffer [Eugeniy]
- Enable unaligned access early to prevent exceptions given newer gcc
code gen [Eugeniy]
- Tighten up uboot arg checking to prevent false negatives and also
allow both jtag and bootloading to coexist w/o config option as
needed by kernelCi folks [Eugeniy]
- Set slab alignment to 8 for ARC to avoid the atomic64_t unalign
[Alexey]
- Disable regfile auto save on interrupts on HSDK platform due to a
silicon issue [Vineet]
- Avoid HS38x boot printing crash by not reading HS48x only reg
[Vineet]"
* tag 'arc-5.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARCv2: don't assume core 0x54 has dual issue
ARC: define ARCH_SLAB_MINALIGN = 8
ARC: enable uboot support unconditionally
ARC: U-boot: check arguments paranoidly
ARCv2: support manual regfile save on interrupts
ARC: uacces: remove lp_start, lp_end from clobber list
ARC: fix actionpoints configuration detection
ARCv2: lib: memcpy: fix doing prefetchw outside of buffer
ARCv2: Enable unaligned access in early ASM code
Daniel Borkmann [Fri, 22 Feb 2019 23:03:44 +0000 (00:03 +0100)]
bpf, doc: add bpf list as secondary entry to maintainers file
We recently created a bpf@vger.kernel.org list (https://lore.kernel.org/bpf/)
for BPF related discussions, originally in context of BPF track at LSF/MM
for topic discussions. It's *optional* but *desirable* to keep it in Cc for
BPF related kernel/loader/llvm/tooling threads, meaning also infrastructure
like llvm that sits on top of kernel but is crucial to BPF. In any case,
netdev with it's bpf delegate is *as-is* today primary list for patches, so
nothing changes in the workflow. Main purpose is to have some more awareness
for the bpf@vger.kernel.org list that folks can Cc for BPF specific topics.
Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Sat, 23 Feb 2019 00:12:01 +0000 (16:12 -0800)]
Merge branch 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"Fix ptrace syscall number modification which has been broken since
kernel v4.5 and provide alternative email addresses for the remaining
users of the retired parisc-linux.org email domain"
* 'parisc-5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
CREDITS/MAINTAINERS: Retire parisc-linux.org email domain
parisc: Fix ptrace syscall number modification
Linus Torvalds [Sat, 23 Feb 2019 00:09:55 +0000 (16:09 -0800)]
Merge tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild fixes from Masahiro Yamada:
- fix scripts/kallsyms.c to correctly check too long symbol names
- fix sh build error for the combination of CONFIG_OF_EARLY_FLATTREE=y
and CONFIG_USE_BUILTIN_DTB=n
* tag 'kbuild-fixes-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
sh: fix build error for invisible CONFIG_BUILTIN_DTB_SOURCE
kallsyms: Handle too long symbols in kallsyms.c
David S. Miller [Sat, 23 Feb 2019 00:05:12 +0000 (16:05 -0800)]
Merge branch 'udp-a-few-fixes'
Paolo Abeni says:
====================
udp: a few fixes
This series includes some UDP-related fixlet. All this stuff has been
pointed out by the sparse tool. The first two patches are just annotation
related, while the last 2 cover some very unlikely races.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:44:00 +0000 (17:44 +0100)]
udp: fix possible user after free in error handler
Similar to the previous commit, this addresses the same issue for
ipv4: use a single fetch operation and use the correct rcu
annotation.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:59 +0000 (17:43 +0100)]
udpv6: fix possible user after free in error handler
Before derefencing the encap pointer, commit e7cc082455cb ("udp: Support
for error handlers of tunnels with arbitrary destination port") checks
for a NULL value, but the two fetch operation can race with removal.
Fix the above using a single access.
Also fix a couple of type annotations, to make sparse happy.
Fixes: e7cc082455cb ("udp: Support for error handlers of tunnels with arbitrary destination port") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:58 +0000 (17:43 +0100)]
fou6: fix proto error handler argument type
Last argument of gue6_err_proto_handler() has a wrong type annotation,
fix it and make sparse happy again.
Fixes: b8a51b38e4d4 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Thu, 21 Feb 2019 16:43:57 +0000 (17:43 +0100)]
udpv6: add the required annotation to mib type
In commit 029a37434880 ("udp6: cleanup stats accounting in recvmsg()")
I forgot to add the percpu annotation for the mib pointer. Add it, and
make sparse happy.
Fixes: 029a37434880 ("udp6: cleanup stats accounting in recvmsg()") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 21 Feb 2019 14:42:01 +0000 (22:42 +0800)]
mdio_bus: Fix use-after-free on device_register fails
KASAN has found use-after-free in fixed_mdio_bus_init,
commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call
put_device on device_register() failure") call put_device()
while device_register() fails,give up the last reference
to the device and allow mdiobus_release to be executed
,kfreeing the bus. However in most drives, mdiobus_free
be called to free the bus while mdiobus_register fails.
use-after-free occurs when access bus again, this patch
revert it to let mdiobus_free free the bus.
KASAN report details as below:
BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482
Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524
Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Kalash Nainwal [Thu, 21 Feb 2019 00:23:04 +0000 (16:23 -0800)]
net: Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255
Set rtm_table to RT_TABLE_COMPAT for ipv6 for tables > 255 to
keep legacy software happy. This is similar to what was done for
ipv4 in commit 709772e6e065 ("net: Fix routing tables with
id > 255 for legacy software").
Signed-off-by: Kalash Nainwal <kalash@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
We were seeing some intermittent firmware message timeouts in our lab and
these 2 small patches fix them. Please apply to stable as well. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:32 +0000 (19:07 -0500)]
bnxt_en: Wait longer for the firmware message response to complete.
The code waits up to 20 usec for the firmware response to complete
once we've seen the valid response header in the buffer. It turns
out that in some scenarios, this wait time is not long enough.
Extend it to 150 usec and use usleep_range() instead of udelay().
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 21 Feb 2019 00:07:31 +0000 (19:07 -0500)]
bnxt_en: Fix typo in firmware message timeout logic.
The logic that polls for the firmware message response uses a shorter
sleep interval for the first few passes. But there was a typo so it
was using the wrong counter (larger counter) for these short sleep
passes. The result is a slightly shorter timeout period for these
firmware messages than intended. Fix it by using the proper counter.
Fixes: 9751e8e71487 ("bnxt_en: reduce timeout on initial HWRM calls") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiong Wang [Fri, 22 Feb 2019 22:36:04 +0000 (22:36 +0000)]
nfp: bpf: fix ALU32 high bits clearance bug
NFP BPF JIT compiler is doing a couple of small optimizations when jitting
ALU imm instructions, some of these optimizations could save code-gen, for
example:
A & -1 = A
A | 0 = A
A ^ 0 = A
However, for ALU32, high 32-bit of the 64-bit register should still be
cleared according to ISA semantics.
Fixes: cd7df56ed3e6 ("nfp: add BPF to NFP code translator") Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Jiong Wang <jiong.wang@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
David S. Miller [Fri, 22 Feb 2019 20:51:21 +0000 (12:51 -0800)]
Merge tag 'mac80211-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Three more fixes:
* mac80211 mesh code wasn't allocating SKB tailroom properly
in some cases
* tx_sk_pacing_shift should be 7 for better performance
* mac80211_hwsim wasn't propagating genlmsg_reply() errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Wed, 20 Feb 2019 22:58:50 +0000 (14:58 -0800)]
Documentation: networking: switchdev: Update port parent ID section
Update the section about switchdev drivers having to implement a
switchdev_port_attr_get() function to return
SWITCHDEV_ATTR_ID_PORT_PARENT_ID since that is no longer valid after
commit bccb30254a4a ("net: Get rid of
SWITCHDEV_ATTR_ID_PORT_PARENT_ID").
Fixes: bccb30254a4a ("net: Get rid of SWITCHDEV_ATTR_ID_PORT_PARENT_ID") Reviewed-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jann Horn [Wed, 20 Feb 2019 21:34:54 +0000 (22:34 +0100)]
net: socket: add check for negative optlen in compat setsockopt
__sys_setsockopt() already checks for `optlen < 0`. Add an equivalent check
to the compat path for robustness. This has to be `> INT_MAX` instead of
`< 0` because the signedness of `optlen` is different here.
Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 20 Feb 2019 17:18:12 +0000 (18:18 +0100)]
ipv6: route: purge exception on removal
When a netdevice is unregistered, we flush the relevant exception
via rt6_sync_down_dev() -> fib6_ifdown() -> fib6_del() -> fib6_del_route().
Finally, we end-up calling rt6_remove_exception(), where we release
the relevant dst, while we keep the references to the related fib6_info and
dev. Such references should be released later when the dst will be
destroyed.
There are a number of caches that can keep the exception around for an
unlimited amount of time - namely dst_cache, possibly even socket cache.
As a result device registration may hang, as demonstrated by this script:
ip netns add cl
ip netns add rt
ip netns add srv
ip netns exec rt sysctl -w net.ipv6.conf.all.forwarding=1
ip link add name cl_veth type veth peer name cl_rt_veth
ip link set dev cl_veth netns cl
ip -n cl link set dev cl_veth up
ip -n cl addr add dev cl_veth 2001::2/64
ip -n cl route add default via 2001::1
ip -n cl link add tunv6 type ip6tnl mode ip6ip6 local 2001::2 remote 2002::1 hoplimit 64 dev cl_veth
ip -n cl link set tunv6 up
ip -n cl addr add 2013::2/64 dev tunv6
ip link set dev cl_rt_veth netns rt
ip -n rt link set dev cl_rt_veth up
ip -n rt addr add dev cl_rt_veth 2001::1/64
ip link add name rt_srv_veth type veth peer name srv_veth
ip link set dev srv_veth netns srv
ip -n srv link set dev srv_veth up
ip -n srv addr add dev srv_veth 2002::1/64
ip -n srv route add default via 2002::2
ip -n srv link add tunv6 type ip6tnl mode ip6ip6 local 2002::1 remote 2001::2 hoplimit 64 dev srv_veth
ip -n srv link set tunv6 up
ip -n srv addr add 2013::1/64 dev tunv6
ip link set dev rt_srv_veth netns rt
ip -n rt link set dev rt_srv_veth up
ip -n rt addr add dev rt_srv_veth 2002::2/64
ip netns exec srv netserver & sleep 0.1
ip netns exec cl ping6 -c 4 2013::1
ip netns exec cl netperf -H 2013::1 -t TCP_STREAM -l 3 & sleep 1
ip -n rt link set dev rt_srv_veth mtu 1400
wait %2
ip -n cl link del cl_veth
This commit addresses the issue purging all the references held by the
exception at time, as we currently do for e.g. ipv6 pcpu dst entries.
v1 -> v2:
- re-order the code to avoid accessing dst and net after dst_dev_put()
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nic: thunderx: fix communication races between VF & PF
The ThunderX CN88XX NIC Virtual Function driver uses mailbox interface
to communicate to physical function driver. Each of VF has it's own pair
of mailbox registers to read from and write to. The mailbox registers
has no protection from possible races, so it has to be implemented
at software side.
After long term testing by loop of 'ip link set <ifname> up/down'
command it was found that there are two possible scenarios when
race condition appears:
1. VF receives link change message from PF and VF send RX mode
configuration message to PF in the same time from separate thread.
2. PF receives RX mode configuration from VF and in the same time,
in separate thread PF detects link status change and sends appropriate
message to particular VF.
Both cases leads to mailbox data to be rewritten, NIC VF messaging control
data to be updated incorrectly and communication sequence gets broken.
This patch series is to address race condition with VF & PF communication.
Changes:
v1 -> v2
- 0000: correct typo in cover letter subject: 'betwen' -> 'between';
- move link state polling request task from pf to vf
instead of cheking status of mailbox irq;
v2 -> v3
- 0003: change return type of nicvf_send_cfg_done() function
from int to void;
- 0007: update subject and remove unused variable 'netdev'
from nicvf_link_status_check_task() function;
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: remove link change polling code and info from nicpf
Since link change polling routine was moved to nicvf side,
we don't need anymore polling function at nicpf side along
with link status info for all enabled Vfs as at VF side
this info is already tracked.
This commit is to remove unnecessary code & fields from
nicpf structure.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:45 +0000 (11:02 +0000)]
net: thunderx: move link state polling function to VF
Move the link change polling task to VF side in order to
prevent races between VF and PF while sending link change
message(s). This commit is to implement link change request
to be initiated by VF.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:44 +0000 (11:02 +0000)]
net: thunderx: add mutex to protect mailbox from concurrent calls for same VF
In some cases it could happen that nicvf_send_msg_to_pf() could be called
concurrently for the same NIC VF, and thus re-writing mailbox contents and
breaking messaging sequence with PF by re-writing NICVF data.
This commit is to implement mutex for NICVF to protect mailbox registers
and NICVF messaging control data from concurrent access.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:44 +0000 (11:02 +0000)]
net: thunderx: add nicvf_send_msg_to_pf result check for set_rx_mode_task
The rx_set_mode invokes number of messages to be send to PF for receive
mode configuration. In case if there any issues we need to stop sending
messages and release allocated memory.
This commit is to implement check of nicvf_msg_send_to_pf() result.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:43 +0000 (11:02 +0000)]
net: thunderx: make CFG_DONE message to run through generic send-ack sequence
At the end of NIC VF initialization VF sends CFG_DONE message to PF without
using nicvf_msg_send_to_pf routine. This potentially could re-write data in
mailbox. This commit is to implement common way of sending CFG_DONE message
by the same way with other configuration messages by using
nicvf_send_msg_to_pf() routine.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vadim Lomovtsev [Wed, 20 Feb 2019 11:02:43 +0000 (11:02 +0000)]
net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.
Having one work queue for receive mode configuration ndo_set_rx_mode()
call for all VFs results in making each of them wait till the
set_rx_mode() call completes for another VF if any of close, set
receive mode and change flags calls being already invoked. Potentially
this could cause device state change before appropriate call of receive
mode configuration completes, so the call itself became meaningless,
corrupt data or break configuration sequence.
We don't need any delays in NIC VF configuration sequence so having delayed
work call with 0 delay has no sense.
This commit is to implement one work queue for each NIC VF for set_rx_mode
task and to let them work independently and replacing delayed_work
with work_struct.
Signed-off-by: Vadim Lomovtsev <vlomovtsev@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 4974d5f678ab ("net: ip6_gre: initialize erspan_ver just for erspan tunnels") Reported-and-tested-by: syzbot+30191cf1057abd3064af@syzkaller.appspotmail.com Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Reviewed-by: Greg Rose <gvrose8192@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
George Wilkie [Wed, 20 Feb 2019 08:19:11 +0000 (08:19 +0000)]
team: use operstate consistently for linkup
When a port is added to a team, its initial state is derived
from netif_carrier_ok rather than netif_oper_up.
If it is carrier up but operationally down at the time of being
added, the port state.linkup will be set prematurely.
port state.linkup should be set consistently using
netif_oper_up rather than netif_carrier_ok.
Fixes: f1d22a1e0595 ("team: account for oper state") Signed-off-by: George Wilkie <gwilkie@vyatta.att-mail.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Chen [Wed, 20 Feb 2019 05:47:19 +0000 (13:47 +0800)]
r8152: Fix an error on RTL8153-BD MAC Address Passthrough support
RTL8153-BD is used in Dell DA300 type-C dongle.
Added RTL8153-BD support to activate MAC address pass through on DA300.
Apply correction on previously submitted patch in net.git tree.
Signed-off-by: David Chen <david.chen7@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 19 Feb 2019 23:15:30 +0000 (00:15 +0100)]
ipvlan: disallow userns cap_net_admin to change global mode/flags
When running Docker with userns isolation e.g. --userns-remap="default"
and spawning up some containers with CAP_NET_ADMIN under this realm, I
noticed that link changes on ipvlan slave device inside that container
can affect all devices from this ipvlan group which are in other net
namespaces where the container should have no permission to make changes
to, such as the init netns, for example.
This effectively allows to undo ipvlan private mode and switch globally to
bridge mode where slaves can communicate directly without going through
hostns, or it allows to switch between global operation mode (l2/l3/l3s)
for everyone bound to the given ipvlan master device. libnetwork plugin
here is creating an ipvlan master and ipvlan slave in hostns and a slave
each that is moved into the container's netns upon creation event.
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l3 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
# docker exec -ti client ip link change link cilium0 name cilium0 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns (mode switched to l2):
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
Same l3 -> l2 switch would also happen by creating another slave inside
the container's network namespace when specifying the existing cilium0
link to derive the actual (bond0) master:
# docker exec -ti client ip link add link cilium0 name cilium1 type ipvlan mode l2
# docker exec -ti client ip -d a
[...]
2: cilium1@if4: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
10: cilium0@if4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.197.43/32 brd 10.41.197.43 scope global cilium0
valid_lft forever preferred_lft forever
* In hostns:
# ip -d a
[...]
8: cilium_host@bond0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/ether 0c:c4:7a:e1:3d:cc brd ff:ff:ff:ff:ff:ff promiscuity 0 minmtu 68 maxmtu 65535
ipvlan mode l2 bridge numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
inet 10.41.0.1/32 scope link cilium_host
valid_lft forever preferred_lft forever
[...]
One way to mitigate it is to check CAP_NET_ADMIN permissions of
the ipvlan master device's ns, and only then allow to change
mode or flags for all devices bound to it. Above two cases are
then disallowed after the patch.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Mahesh Bandewar <maheshb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Kwiecien [Fri, 22 Feb 2019 08:45:26 +0000 (09:45 +0100)]
sctp: don't compare hb_timer expire date before starting it
hb_timer might not start at all for a particular transport because its
start is conditional. In a result a node is not sending heartbeats.
Function sctp_transport_reset_hb_timer has two roles:
- initial start of hb_timer for a given transport,
- update expire date of hb_timer for a given transport.
The function is optimized to update timer's expire only if it is before
a new calculated one but this comparison is invalid for a timer which
has not yet started. Such a timer has expire == 0 and if a new expire
value is bigger than (MAX_JIFFIES / 2 + 2) then "time_before" macro will
fail and timer will not start resulting in no heartbeat packets send by
the node.
This was found when association was initialized within first 5 mins
after system boot due to jiffies init value which is near to MAX_JIFFIES.
Test kernel version: 4.9.154 (ARCH=arm)
hb_timer.expire = 0; //initialized, not started timer
new_expire = MAX_JIFFIES / 2 + 2; //or more
time_before(hb_timer.expire, new_expire) == false
Fixes: ba6f5e33bdbb ("sctp: avoid refreshing heartbeat timer too often") Reported-by: Marcin Stojek <marcin.stojek@nokia.com> Tested-by: Marcin Stojek <marcin.stojek@nokia.com> Signed-off-by: Maciej Kwiecien <maciej.kwiecien@nokia.com> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 22 Feb 2019 18:35:06 +0000 (10:35 -0800)]
Merge tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This contains a single i915 tiled display fix, and a set of
amdgpu/radeon fixes.
i915:
- tiled display fix
amdgpu/radeon:
- runtime PM fix
- bulk moves disable (fix is too large for 5.0)
- a set of display fixes that are all cc'ed stable so we didn't want
to leave them until -next"
* tag 'drm-fixes-2019-02-22' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: disable bulk moves for now
drm/amd/display: set clocks to 0 on suspend on dce80
drm/amd/display: fix optimize_bandwidth func pointer for dce80
drm/amd/display: Fix negative cursor pos programming
drm/i915/fbdev: Actually configure untiled displays
drm/amd/display: Raise dispclk value for dce11
drm/amd/display: Fix MST reboot/poweroff sequence
drm/amdgpu: Update sdma golden setting for vega20
drm/amdgpu: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
gpu: drm: radeon: Set DPM_FLAG_NEVER_SKIP when enabling PM-runtime
Linus Torvalds [Fri, 22 Feb 2019 18:32:26 +0000 (10:32 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Small set of three regression fixing patches, things are looking
pretty good here.
- Fix cxgb4 to work again with non-4k page sizes
- NULL pointer oops in SRP during sg_reset"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
iw_cxgb4: cq/qp mask depends on bar2 pages in a host page
cxgb4: Export sge_host_page_size to ulds
RDMA/srp: Rework SCSI device reset handling
Yu Zhang [Thu, 31 Jan 2019 16:09:23 +0000 (00:09 +0800)]
KVM: MMU: record maximum physical address width in kvm_mmu_extended_role
Previously, commit 7dcd57552008 ("x86/kvm/mmu: check if tdp/shadow
MMU reconfiguration is needed") offered some optimization to avoid
the unnecessary reconfiguration. Yet one scenario is broken - when
cpuid changes VM's maximum physical address width, reconfiguration
is needed to reset the reserved bits. Also, the TDP may need to
reset its shadow_root_level when this value is changed.
To fix this, a new field, maxphyaddr, is introduced in the extended
role structure to keep track of the configured guest physical address
width.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yu Zhang [Thu, 31 Jan 2019 16:09:43 +0000 (00:09 +0800)]
kvm: x86: Return LA57 feature based on hardware capability
Previously, 'commit 372fddf70904 ("x86/mm: Introduce the 'no5lvl' kernel
parameter")' cleared X86_FEATURE_LA57 in boot_cpu_data, if Linux chooses
to not run in 5-level paging mode. Yet boot_cpu_data is queried by
do_cpuid_ent() as the host capability later when creating vcpus, and Qemu
will not be able to detect this feature and create VMs with LA57 feature.
As discussed earlier, VMs can still benefit from extended linear address
width, e.g. to enhance features like ASLR. So we would like to fix this,
by return the true hardware capability when Qemu queries.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Vitaly Kuznetsov [Fri, 22 Feb 2019 16:45:01 +0000 (17:45 +0100)]
x86/kvm/mmu: fix switch between root and guest MMUs
Commit 14c07ad89f4d ("x86/kvm/mmu: introduce guest_mmu") brought one subtle
change: previously, when switching back from L2 to L1, we were resetting
MMU hooks (like mmu->get_cr3()) in kvm_init_mmu() called from
nested_vmx_load_cr3() and now we do that in nested_ept_uninit_mmu_context()
when we re-target vcpu->arch.mmu pointer.
The change itself looks logical: if nested_ept_init_mmu_context() changes
something than nested_ept_uninit_mmu_context() restores it back. There is,
however, one thing: the following call chain:
now happens with MMU hooks pointing to the new MMU (root MMU in our case)
while previously it was happening with the old one. cached_root_available()
tries to stash current root but it is incorrect to read current CR3 with
mmu->get_cr3(), we need to use old_mmu->get_cr3() which in case we're
switching from L2 to L1 is guest_mmu. (BTW, in shadow page tables case this
is a non-issue because we don't switch MMU).
While we could've tried to guess that we're switching between MMUs and call
the right ->get_cr3() from cached_root_available() this seems to be overly
complicated. Instead, just stash the corresponding CR3 when setting
root_hpa and make cached_root_available() use the stashed value.
syzbot hit the 'BUG_ON(index_key->desc_len == 0);' in __key_link_begin()
called from construct_alloc_key() during sys_request_key(), because the
length of the key description was never calculated.
The problem is that we rely on ->desc_len being initialized by
search_process_keyrings(), specifically by search_nested_keyrings().
But, if the process isn't subscribed to any keyrings that never happens.
Fix it by always initializing keyring_index_key::desc_len as soon as the
description is set, like we already do in some places.
The following program reproduces the BUG_ON() when it's run as root and
no session keyring has been installed. If it doesn't work, try removing
pam_keyinit.so from /etc/pam.d/login and rebooting.
Reported-by: syzbot+ec24e95ea483de0a24da@syzkaller.appspotmail.com Fixes: b2a4df200d57 ("KEYS: Expand the capacity of a keyring") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David Howells <dhowells@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: James Morris <james.morris@microsoft.com>
Eric Biggers [Wed, 20 Feb 2019 13:32:11 +0000 (13:32 +0000)]
KEYS: user: Align the payload buffer
Align the payload of "user" and "logon" keys so that users of the
keyrings service can access it as a struct that requires more than
2-byte alignment. fscrypt currently does this which results in the read
of fscrypt_key::size being misaligned as it needs 4-byte alignment.
Align to __alignof__(u64) rather than __alignof__(long) since in the
future it's conceivable that people would use structs beginning with
u64, which on some platforms would require more than 'long' alignment.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Fixes: 2aa349f6e37c ("[PATCH] Keys: Export user-defined keyring operations") Fixes: 88bd6ccdcdd6 ("ext4 crypto: add encryption key management facilities") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: James Morris <james.morris@microsoft.com>
Charles Keepax [Fri, 22 Feb 2019 10:04:21 +0000 (10:04 +0000)]
ASoC: wm_adsp: Improve logging messages
As the compressed stream implementation has acquired support for
multiple DAI links and compressed streams it has become harder to
interpret messages in the kernel log. Add additional macros to include
the compressed DAI name in the log messages, allowing different streams
to be easily disambiguated.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Stuart Henderson [Fri, 22 Feb 2019 10:04:20 +0000 (10:04 +0000)]
ASoC: wm_adsp: Add support for multiple compressed buffers
Currently, only a single compressed stream is supported per firmware.
Add support for multiple compressed streams on a single firmware, this
allows additional features like completely independent trigger words or
separate debug capture streams to be implemented.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Dan Carpenter [Fri, 22 Feb 2019 06:31:51 +0000 (09:31 +0300)]
ASoC: cs35l36: Fix an IS_ERR() vs NULL checking bug
The irq_get_irq_data() function doesn't return error pointers, it
returns NULL.
Fixes: 6ba9dd6c893b ("ASoC: cs35l36: Add support for Cirrus CS35L36 Amplifier") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
Arnd Bergmann [Fri, 22 Feb 2019 13:57:27 +0000 (14:57 +0100)]
Merge tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu into arm/fixes
mvebu fixes for 5.0 (part 2)
Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release
* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
Arnd Bergmann [Fri, 22 Feb 2019 13:53:48 +0000 (14:53 +0100)]
Merge tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Two am335x ethernet phy mode fixes for v5.0-rc cycle
Recent changes with commit cd28d1d6e52e: ("net: phy: at803x: Disable phy
delay for RGMII mode") broke Ethernet on am335x-evmsk, and turns out some
device driver fixes are needed.
Even without the driver fixes, am335x needs to run in rgmii-id mode instead
rgmii-txid mode. Things have been working based on luck as the broken driver
has been configuring rgmii-id mode. Let's fix that as that way things work
as they're supposed to work from hardware wiring point of view.
* tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
Felix Fietkau [Fri, 22 Feb 2019 12:21:15 +0000 (13:21 +0100)]
mac80211: allocate tailroom for forwarded mesh packets
Forwarded packets enter the tx path through ieee80211_add_pending_skb,
which skips the ieee80211_skb_resize call.
Fixes WARN_ON in ccmp_encrypt_skb and resulting packet loss.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we did the original tests for the optimal value of sk_pacing_shift, we
came up with 6 ms of buffering as the default. Sadly, 6 is not a power of
two, so when picking the shift value I erred on the size of less buffering
and picked 4 ms instead of 8. This was probably wrong; those 2 ms of extra
buffering makes a larger difference than I thought.
So, change the default pacing shift to 7, which corresponds to 8 ms of
buffering. The point of diminishing returns really kicks in after 8 ms, and
so having this as a default should cut down on the need for extensive
per-device testing and overrides needed in the drivers.
Cc: stable@vger.kernel.org Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sameer Pujar [Wed, 20 Feb 2019 15:13:24 +0000 (20:43 +0530)]
ALSA: hda/tegra: sound card name from device tree
A platform can have multiple sound cards for different audio paths.
Following is the print seen duirng device boot for jetson-xavier,
ALSA device list:
#0: nvidia,p2972-0000 at 0x3518000 irq 17
By looking at above, it is not very clear if the sound card is for
HDA. It becomes confusing when platform has registered multiple cards,
and platform model name is used for card.
This patch uses "nvidia,model" property mentioned in hda device tree
to get the card name. Since property is optional, legacy boards will
continue to use "tegra-hda". Custom name can be passed wherever needed.
This naming convention is conistent with the way sound cards are named
in general.
Sameer Pujar [Wed, 20 Feb 2019 15:13:23 +0000 (20:43 +0530)]
arm64: tegra: custom name for hda sound card
"nvidia,model" property is added to pass custom name for hda sound card.
This is parsed in hda driver and used for card name. This aligns with the
way with which sound cards are named in general.
This patch populates above for jetson-tx1, jetson-tx2 and jetson-xavier.
Sameer Pujar [Wed, 20 Feb 2019 15:13:22 +0000 (20:43 +0530)]
ALSA: hda/tegra: property for card name
An optional property "nvidia,model" is introduced for hda to pass custom
name for the sound card. The suffix "-hda" in the name passed is useful
to distinguish between multiple cards available for a platform.
When the property is not specified, default name("tegra-hda") mentioned
in hda driver is used. This property can be added in platform specific
file of the board and card name can relate to the board in use.