Quan Nguyen [Tue, 5 Sep 2017 18:16:31 +0000 (11:16 -0700)]
drivers: net: xgene: Configure tx/rx delay for ACPI
This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com> Signed-off-by: Quan Nguyen <qnguyen@apm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.
The change was done using the following coccinelle script:
rds: Fix non-atomic operation on shared flag variable
The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com> Reviewed-by: Knut Omang <knut.omang@oracle.com> Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Try to preallocate the memory with idr_prealloc(GFP_KERNEL)
(as suggested by Eric Dumazet), and change the allocation
flags under spin lock.
Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 5 Sep 2017 01:22:05 +0000 (09:22 +0800)]
vhost_net: correctly check tx avail during rx busy polling
We check tx avail through vhost_enable_notify() in the past which is
wrong since it only checks whether or not guest has filled more
available buffer since last avail idx synchronization which was just
done by vhost_vq_avail_empty() before. What we really want is checking
pending buffers in the avail ring. Fix this by calling
vhost_vq_avail_empty() instead.
This issue could be noticed by doing netperf TCP_RR benchmark as
client from guest (but not host). With this fix, TCP_RR from guest to
localhost restores from 1375.91 trans per sec to 55235.28 trans per
sec on my laptop (Intel(R) Core(TM) i7-5600U CPU @ 2.60GHz).
Fixes: 030881372460 ("vhost_net: basic polling support") Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Mon, 4 Sep 2017 14:28:28 +0000 (15:28 +0100)]
rxrpc: Make service connection lookup always check for retry
When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.
Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful. This makes sure we always pick up on a write-lock
event.
On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: stmmac: Delete dead code for MDIO registration
This code is no longer used, the logging function was changed by commit fbca164776e4 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776e4 ("net: stmmac: Use the right logging function in stmmac_mdio_register") Signed-off-by: Romain Perier <romain.perier@collabora.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3ccd9e34f28e6ec677b812a860eb8eb ("gianfar: Implement PAUSE frame generation support") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_TX_INT_CAUSE[Bubble] is a normal condition for T6, hence
ignore this interrupt for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_STAT_CTL[CountPauseStatTx] and MPS_STAT_CTL[CountPauseStatRx]
only control whether or not Pause Frames will be counted as part
of the 64-Byte Tx/Rx Frame counters. These bits do not control
whether Pause Frames are counted in the Total Tx/Rx Frames/Bytes
counters.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by: Casey Leedom <leedom@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Mon, 4 Sep 2017 03:36:08 +0000 (11:36 +0800)]
tun: reserve extra headroom only when XDP is set
We reserve headroom unconditionally which could cause unnecessary
stress on socket memory accounting because of increased trusesize. Fix
this by only reserve extra headroom when XDP is set.
Cc: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 5 Sep 2017 18:53:34 +0000 (11:53 -0700)]
Merge branch 'dsa-tx-queues'
Florian Fainelli says:
====================
net: dsa: Allow switch drivers to indicate number of TX queues
This patch series extracts the parts of the patch set that are likely not to be
controversial and actually bringing multi-queue support to DSA-created network
devices.
With these patches, we can now use sch_multiq as documented under
Documentation/networking/multique.txt and let applications dedice the switch
port output queue they want to use. Currently only Broadcom tags utilize that
information.
Resending based on David's feedback regarding the patches not in patchwork.
Changes in v2:
- use a proper define for the number of TX queues in bcm_sf2.c (Andrew)
Changes from RFC:
- dropped the ability to configure RX queues since we don't do anything with
those just yet
- dropped the patches that dealt with binding the DSA slave network devices
queues with their master network devices queues this will be worked on
separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: bcm_sf2: Advertise number of egress queues
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: tag_brcm: Set output queue from skb queue mapping
We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: Allow switch drivers to indicate number of TX queues
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: switchdev: Use an helper to clear forward mark
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Tested-by: Yotam Gigi <yotamg@mellanox.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Meyer [Sun, 3 Sep 2017 12:19:31 +0000 (14:19 +0200)]
net/mlx4_core: Use ARRAY_SIZE macro
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set fixes some basic issues with __skb_flow_dissect function.
Items addressed:
- Cleanup control flow in the function; in particular eliminate a
bunch of goto's and implement a simplified control flow model
- Add limits for number of encapsulations and headers that can be
dissected
v2:
- Simplify the logic for limits on flow dissection. Just set the
limit based on the number of headers the flow dissector can
processes. The accounted headers includes encapsulation headers,
extension headers, or other shim headers.
Tested:
Ran normal traffic, GUE, and VXLAN traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 1 Sep 2017 21:04:12 +0000 (14:04 -0700)]
flow_dissector: Add limit for number of headers to dissect
In flow dissector there are no limits to the number of nested
encapsulations or headers that might be dissected which makes for a
nice DOS attack. This patch sets a limit of the number of headers
that flow dissector will parse.
Headers includes network layer headers, transport layer headers, shim
headers for encapsulation, IPv6 extension headers, etc. The limit for
maximum number of headers to parse has be set to fifteen to account for
a reasonable number of encapsulations, extension headers, VLAN,
in a packet. Note that this limit does not supercede the STOP_AT_*
flags which may stop processing before the headers limit is reached.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert [Fri, 1 Sep 2017 21:04:11 +0000 (14:04 -0700)]
flow_dissector: Cleanup control flow
__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.
Reported-by: Alexander Popov <alex.popov@linux.com> Signed-off-by: Tom Herbert <tom@quantonium.net> Signed-off-by: David S. Miller <davem@davemloft.net>
A header file cleanup apparently caused a build regression
with one driver using the knav infrastructure:
In file included from drivers/net/ethernet/ti/netcp_core.c:30:0:
include/linux/soc/ti/knav_dma.h:129:30: error: field 'direction' has incomplete type
enum dma_transfer_direction direction;
^~~~~~~~~
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_txpipe_open':
drivers/net/ethernet/ti/netcp_core.c:1349:21: error: 'DMA_MEM_TO_DEV' undeclared (first use in this function); did you mean 'DMA_MEMORY_MAP'?
config.direction = DMA_MEM_TO_DEV;
^~~~~~~~~~~~~~
DMA_MEMORY_MAP
drivers/net/ethernet/ti/netcp_core.c:1349:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_setup_navigator_resources':
drivers/net/ethernet/ti/netcp_core.c:1659:22: error: 'DMA_DEV_TO_MEM' undeclared (first use in this function); did you mean 'DMA_DESC_HOST'?
config.direction = DMA_DEV_TO_MEM;
As the header is no longer included implicitly through netdevice.h,
we should include it in the header that references the enum.
Fixes: 0dd5759dbb1c ("net: remove dmaengine.h inclusion from netdevice.h") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Related to that, we get another error when CONFIG_NET_NCSI is disabled:
drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?
This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.
Fixes: 51564585d8c6 ("ftgmac100: Support NCSI VLAN filtering when available") Fixes: 21acf63013ed ("net/ncsi: Configure VLAN tag filter") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 96eabe7a40aa ("bpf: Allow selecting numa node during map creation") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Alexei Starovoitov <ast@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for next-net (part 2)
The following patchset contains Netfilter updates for net-next. This
patchset includes updates for nf_tables, removal of
CONFIG_NETFILTER_DEBUG and a new mode for xt_hashlimit. More
specifically, they:
1) Add new rate match mode for hashlimit, this introduces a new revision
for this match. The idea is to stop matching packets until ratelimit
criteria stands true. Patch from Vishwanath Pai.
2) Add ->select_ops indirection to nf_tables named objects, so we can
choose between different flavours of the same object type, patch from
Pablo M. Bermudo.
3) Shorter function names in nft_limit, basically:
s/nft_limit_pkt_bytes/nft_limit_bytes, also from Pablo M. Bermudo.
4) Add new stateful limit named object type, this allows us to create
limit policies that you can identify via name, also from Pablo.
5) Remove unused hooknum parameter in conntrack ->packet indirection.
From Florian Westphal.
6) Patches to remove CONFIG_NETFILTER_DEBUG and macros such as
IP_NF_ASSERT and IP_NF_ASSERT. From Varsha Rao.
7) Add nf_tables_updchain() helper function and use it from
nf_tables_newchain() to make it more maintainable. Similarly,
add nf_tables_addchain() and use it too.
8) Add new netlink NLM_F_NONREC flag, this flag should only be used for
deletion requests, specifically, to support non-recursive deletion.
Based on what we discussed during NFWS'17 in Faro.
9) Use NLM_F_NONREC from table and sets in nf_tables.
10) Support for recursive chain deletion. Table and set deletion
commands come with an implicit content flush on deletion, while
chains do not. This patch addresses this inconsistency by adding
the code to perform recursive chain deletions. This also comes with
the bits to deal with the new NLM_F_NONREC netlink flag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_tables: support for recursive chain deletion
This patch sorts out an asymmetry in deletions. Currently, table and set
deletion commands come with an implicit content flush on deletion.
However, chain deletion results in -EBUSY if there is content in this
chain, so no implicit flush happens. So you have to send a flush command
in first place to delete chains, this is inconsistent and it can be
annoying in terms of user experience.
This patch uses the new NLM_F_NONREC flag to request non-recursive chain
deletion, ie. if the chain to be removed contains rules, then this
returns EBUSY. This problem was discussed during the NFWS'17 in Faro,
Portugal. In iptables, you hit -EBUSY if you try to delete a chain that
contains rules, so you have to flush first before you can remove
anything. Since iptables-compat uses the nf_tables netlink interface, it
has to use the NLM_F_NONREC flag from userspace to retain the original
iptables semantics, ie. bail out on removing chains that contain rules.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: use NLM_F_NONREC for deletion requests
Bail out if user requests non-recursive deletion for tables and sets.
This new flags tells nf_tables netlink interface to reject deletions if
tables and sets have content.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netlink: add NLM_F_NONREC flag for deletion requests
In the last NFWS in Faro, Portugal, we discussed that netlink is lacking
the semantics to request non recursive deletions, ie. do not delete an
object iff it has child objects that hang from this parent object that
the user requests to be deleted.
We need this new flag to solve a problem for the iptables-compat
backward compatibility utility, that runs iptables commands using the
existing nf_tables netlink interface. Specifically, custom chains in
iptables cannot be deleted if there are rules in it, however, nf_tables
allows to remove any chain that is populated with content. To sort out
this asymmetry, iptables-compat userspace sets this new NLM_F_NONREC
flag to obtain the same semantics that iptables provides.
This new flag should only be used for deletion requests. Note this new
flag value overlaps with the existing:
* NLM_F_ROOT for get requests.
* NLM_F_REPLACE for new requests.
However, those flags should not ever be used in deletion requests.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Vishwanath Pai [Fri, 18 Aug 2017 18:58:59 +0000 (20:58 +0200)]
netfilter: xt_hashlimit: add rate match mode
This patch adds a new feature to hashlimit that allows matching on the
current packet/byte rate without rate limiting. This can be enabled
with a new flag --hashlimit-rate-match. The match returns true if the
current rate of packets is above/below the user specified value.
The main difference between the existing algorithm and the new one is
that the existing algorithm rate-limits the flow whereas the new
algorithm does not. Instead it *classifies* the flow based on whether
it is above or below a certain rate. I will demonstrate this with an
example below. Let us assume this rule:
iptables -A INPUT -m hashlimit --hashlimit-above 10/s -j new_chain
If the packet rate is 15/s, the existing algorithm would ACCEPT 10
packets every second and send 5 packets to "new_chain".
But with the new algorithm, as long as the rate of 15/s is sustained,
all packets will continue to match and every packet is sent to new_chain.
This new functionality will let us classify different flows based on
their current rate, so that further decisions can be made on them based on
what the current rate is.
This is how the new algorithm works:
We divide time into intervals of 1 (sec/min/hour) as specified by
the user. We keep track of the number of packets/bytes processed in the
current interval. After each interval we reset the counter to 0.
When we receive a packet for match, we look at the packet rate
during the current interval and the previous interval to make a
decision:
if [ prev_rate < user and cur_rate < user ]
return Below
else
return Above
Where cur_rate is the number of packets/bytes seen in the current
interval, prev is the number of packets/bytes seen in the previous
interval and 'user' is the rate specified by the user.
We also provide flexibility to the user for choosing the time
interval using the option --hashilmit-interval. For example the user can
keep a low rate like x/hour but still keep the interval as small as 1
second.
To preserve backwards compatibility we have to add this feature in a new
revision, so I've created revision 3 for hashlimit. The two new options
we add are:
--hashlimit-rate-match
--hashlimit-rate-interval
I have updated the help text to add these new options. Also added a few
tests for the new options.
Suggested-by: Igor Lubashev <ilubashe@akamai.com> Reviewed-by: Josh Hunt <johunt@akamai.com> Signed-off-by: Vishwanath Pai <vpai@akamai.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
====================
net: qualcomm: rmnet: Fix comments on initial patchset
This series fixes the comments from Dan on the first patch series.
Fixes a memory corruption which could occur if mux_id was higher than 32.
Remove the RMNET_LOCAL_LOGICAL_ENDPOINT which is no longer used.
Make a log message more useful.
Combine __rmnet_set_endpoint_config() with rmnet_set_endpoint_config().
Set the mux_id in rmnet_vnd_newlink().
Set the ingress and egress data format directly in newlink.
Implement ndo_get_iflink to find the real_dev.
Rename the real_dev_info to port to make it similar to other drivers.
The conversion of rmnet_devices to a list and hash lookup will be sent
as part of a seperate patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Rename real_dev_info to port
Make it similar to drivers like ipvlan / macvlan so it is easier to read.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Refactor the new rmnet dev creation
Data format can be directly set from rmnet_newlink() since the
rmnet real dev info is already available.
Since __rmnet_get_real_dev_info() is no longer used in rmnet_config.c
after removal of those functions, move content to
rmnet_get_real_dev_info().
__rmnet_set_endpoint_config() is collapsed into
rmnet_set_endpoint_config() since only mux_id was being set additionally
within it. Remove an unnecessary mux_id check.
Set the mux_id for the rmnet_dev within rmnet_vnd_newlink() itself.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Remove the unused endpoint -1
This was used only in the original patch series where the IOCTLs were
present and is no longer in use.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: qualcomm: rmnet: Fix memory corruption if mux_id is greater than 32
rmnet_rtnl_validate() was checking for upto mux_id 254, however the
rmnet_devices devices could hold upto 32 entries only. Fix this by
increasing the size of the rmnet_devices.
Fixes: ceed73a2cf4a ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org> Cc: Dan Williams <dcbw@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
nfp: refactor app init, and minor flower fixes
This series is a part 2 to what went into net as a simpler fix.
In net we simply moved when existing callbacks are invoked to
ensure flower app does not still use representors when lower
netdev has already been destroyed. In this series we add a
callback to notify apps when vNIC netdevs are fully initialized
and they are about to be destroyed. This allows flower to spawn
representors at the right time, while keeping the start/stop
callbacks for what they are intended to be used - FW initialization
over control channel.
Patch 4 improves drop monitor interaction and patch 5 changes
the default Kconfig selection of flower offload. Patch 6 fixes
locking around representor updates which got lost in net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:05 +0000 (18:26 -0700)]
nfp: flower: restore RTNL locking around representor updates
When we moved to updating representors from a workqueue grabbing
the RTNL somehow got lost in the process. Restore it, and make
sure RCU lock is not held while we are grabbing the RTNL. RCU
protects the representor table, so since we will be under RTNL
we can drop RCU lock as soon as we find the netdev pointer.
RTNL is needed for the dev_set_mtu() call.
Fixes: 2dff19622421 ("nfp: process MTU updates from firmware flower app") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:04 +0000 (18:26 -0700)]
nfp: build the flower offload by default
It's reasonable to assume that if user selects to build the NFP
driver all offload capabilities will be enabled by default.
Change the CONFIG_NFP_APP_FLOWER to default to enabled.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:03 +0000 (18:26 -0700)]
nfp: be drop monitor friendly
Use dev_consume_skb_any() in place of dev_kfree_skb_any()
when control frame has been successfully processed in flower
and on the driver's main TX completion path.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:02 +0000 (18:26 -0700)]
nfp: move the start/stop app callbacks back
Since representors are now created with a separate callback
start/stop app callbacks can be moved again to their original
location. They are intended to app-specific init/clean up
over the control channel.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:01 +0000 (18:26 -0700)]
nfp: flower: base lifetime of representors on existence of lower vNIC
Create representors after lower vNIC is registered and destroy
them before it is destroyed. Move the code out of start/stop
callbacks directly into vnic_init/clean callbacks. Make sure
SR-IOV callbacks don't try to create representors when lower
device does not exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sun, 3 Sep 2017 01:26:00 +0000 (18:26 -0700)]
nfp: separate app vNIC init/clean from alloc/free
We currently only have one app callback for vNIC creation
and destruction. This is insufficient, because some actions
have to be taken before netdev is registered, after it's
registered and after it's unregistered. Old callbacks
were really corresponding to alloc/free actions. Rename
them and add proper init/clean. Apps using representors
will be able to use new callbacks to manage lifetime of
upper devices.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 Sep 2017 04:17:07 +0000 (21:17 -0700)]
Merge tag 'mlx5-updates-2017-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-09-03
This series from Tariq includes micro data path optimization for mlx5e
netdevice driver.
Mainly Tariq introduces the following changes to NAPI and RX handling
path of the driver:
- RX ring structure reorganizing
- Trivial code refactoring and optimization
- NAPI busy-poll for when fast UMR is in progress
- Non-atomic state operations in NAPI context
- Remove unnecessary fields from fast path structures
- page-cache micro optimization
- Rely on NAPI to avoid missing an IRQ for RX/TX shared NAPI contexts
- Stop NAPI when irq changes affinity
- Distribute RSS table among all RX rings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 4 Sep 2017 03:23:26 +0000 (20:23 -0700)]
Merge branch 'mlxsw-Offloading-GRE-tunnels'
Jiri Pirko says:
====================
mlxsw: Offloading GRE tunnels
Petr says:
This patch series introduces to mlxsw driver support for offloading
IP-in-IP tunnels in general, and for (subset of) GRE in particular.
This patchset supports two ways of configuring GRE:
- So called "hierarchical configuration", where the GRE device has a bound
dummy device, which is in a different VRF. The VRF with host traffic is
called "overlay", the one with encapsulated traffic is called "underlay".
- So called "flat configuration", where the GRE device doesn't have a bound
device, and overlay and underlay are both in the same VRF (possibly the
default one).
Two routes are then interesting: a route that directs traffic to a GRE
device (which would typically be in overlay VRF, but could be in another
one), and a local route for the tunnel's local address (in underlay).
Handling of these two route types is then introduced as patches to support,
respectively, IPv4 and IPv6 encapsulation and IPv4 decapsulation.
The encap and decap routes then reference a loopback device, a new type of
RIF introduced by this patchset for the specific use of offloading tunnels.
The encap and decap code is abstract with respect to the particulars of
individual L3 tunnel types. This patchset introduces support for GRE
tunnels in particular.
Limitations:
- Each tunnel needs to have a different local address (within a given VRF).
When two tunnels are used that are in conflict, FIB abort is triggered
and the driver ceases offloading FIBs. Full handling of such
configurations needs special setup in the hardware, such that the tunnels
that share an address are dispatched correctly according to their key (or
lack thereof). That's currently not implemented, and to keep things
deterministic, the driver triggers FIB abort.
- A next hop that uses an incompletely-specified tunnel (e.g. such that are
used for LWT) is not offloaded, but doesn't trigger FIB abort like the
above. If such routes end up being in a de facto conflict with other
tunnels, then if there already is an offload for that address, the
traffic for the conflicting tunnel will end up mismatching the
configuration of the offloaded tunnel, and thus gets to slow path through
an error trap.
- GRE checksumming and sequence numbers are not supported and TTL and TOS
need to be set to inherit. Tunnels with a different configuration are not
offloaded and their traffic is trapping to slow path.
Note in particular that TOS of inherit is not the default configuration
and needs to be explicitly specified when the tunnel is created.
- The only feature that is not graciously handled is that if a change is
made to the tunnel, e.g. through "ip tunnel change", such changes are not
reflected in the driver. There is currently no notification mechanism for
these changes. Introduction of this mechanism and its leverage in the
driver will be subject of follow-up work. For now this limitation can be
worked around by removing and re-adding the encap route.
---
v1->v2:
-fix order of patch 5
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:29 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Support GRE tunnels
This patch introduces callbacks and tunnel type to offload GRE tunnels.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:28 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Add loopback accessors
struct mlxsw_sp_rif is a router-private structure, and therefore
everything related to it is as well: parameters, and derived RIF types
including loopbacks. IPIP module needs access to some details of
loopback interfaces, but exporting all the RIF shebang would create too
large an interface.
So instead export just the bare minimum necessary: accessors for RIF
index and underlay VRF ID.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:27 +0000 (23:49 +0200)]
mlxsw: spectrum: Register for IPIP_DECAP_ERROR trap
These traps are generated for packets that fail checks for source IP,
encapsulation type, or GRE key. Trap these packets to CPU for follow-up
handling by the kernel, which will send ICMP destination unreachable
responses.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:26 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Use existing decap route
The local route that points at IPIP's underlay device (decap route) can
be present long before the GRE device. Thus when an encap route is
added, it's necessary to look inside the underlay FIB if the decap route
is already present. If so, the current trap offload needs to be
withdrawn and replaced with a decap offload.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:25 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Support IPv4 underlay decap
Unlike encapsulation, which is represented by a next hop forwarding to
an IPIP tunnel, decapsulation is a type of local route. It is created
for local routes whose prefix corresponds to the local address of one of
offloaded IPIP tunnels. When the tunnel is removed (i.e. all the encap
next hops are removed), the decap offload is migrated back to a trap for
resolution in slow path.
This patch assumes that decap route is already present when encap route
is added. A follow-up patch will fix this issue.
Note that this patch only supports IPv4 underlay. Support for IPv6
underlay will be subject to follow-up work apart from this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:24 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Support IPv6 overlay encap
Add the missing bits to recognize IPv6 next hops as IPIP ones to enable
offloading of IPv6 overlay encapsulation.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:23 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Support IPv4 overlay encap
This introduces some common code for tracking of offloaded IP-in-IP
tunnels, and support for offloading IPv4 overlay encapsulating routes in
particular. A follow-up patch will introduce IPv6 overlay as well.
Offloaded tunnels are kept in a linked list of mlxsw_sp_ipip_entry
objects hooked up in mlxsw_sp_router. A network device that represents
the tunnel is used as a key to look up the corresponding IPIP entry.
Note that in the future, more general keying mechanism will be needed,
because parts of the tunnel information can be provided by the route.
IPIP entries are reference counted, because several next hops may end up
using the same tunnel, and we only want to offload it once.
Encapsulation path hooks into next hop handling. Routes that forward to
a tunnel are now considered gateway routes, thus giving them the same
treatment that other remote routes get. An IPIP next hop type is
introduced.
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. If a tunnel type doesn't match any of the
known tunnel types, the next-hop is not considered an IPIP next hop.
The list of IPIP tunnel types is currently empty, follow-up patches will
add support for GRE. Traffic to IPIP tunnel types that are not
explicitly recognized by the driver traps and is handled in slow path.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:22 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Make nexthops typed
In the router, some next hops may reference an encapsulating netdevice,
such as GRE or IPIP. To properly offload these next hops, mlxsw needs to
keep track of whether a given next hop is a regular Ethernet entry, or
an IP-in-IP tunneling entry.
To facilitate this book-keeping, add a type field to struct
mlxsw_sp_nexthop. There is, as of this patch, only one next hop type:
MLXSW_SP_NEXTHOP_TYPE_ETH. Follow-up patches will introduce the IP-in-IP
variant.
There are several places where next hops are initialized in the IPv4
path. Instead of replicating the logic at every one of them, factor it
out to a function mlxsw_sp_nexthop4_type_init(). The corresponding fini
is actually protocol-neutral, so put it to mlxsw_sp_nexthop_type_fini(),
but create a corresponding protocoled _fini function that dispatches to
the protocol-neutral one.
The IPv6 path is simpler, but for symmetry with IPv4, create the same
suite of functions with corresponding logic.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 counterpart of the previous patch: introduce a function to
determine whether a given route is a gateway route.
The new function takes a mlxsw_sp argument which follow-up patches will
use. Thus mlxsw_sp_fib6_entry_type_set() got that argument as well.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For IPv4 IP-in-IP offload, routes that direct traffic to IP-in-IP
devices need to be considered gateway routes as well. That involves a
bit more logic, so extract the current test to a separate function,
where the logic can be later added.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:19 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Introduce loopback RIFs
When offloading L3 tunnels, an adjacency entry is created that loops the
packet back into the underlay router. Loopback interfaces then hold the
corresponding information and are created for IP-in-IP netdevices.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:18 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Support FID-less RIFs
Loopback RIFs, which will be introduced in a follow-up patch, differ
from other RIFs in that they do not have a FID associated with them.
To support this, demote FID allocation from mlxsw_sp_rif_create to
configure op of the existing RIF types, and likewise the FID release
from mlxsw_sp_rif_destroy to deconfigure op.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:17 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Add mlxsw_sp_ipip_ops
Details of individual tunnel types are kept in an array of
mlxsw_sp_ipip_ops objects. Follow-up patches will use the list to
determine whether a constructed RIF should be a loopback, and to decide
whether a next hop references a tunnel.
The list is currently empty, follow-up patches will add support for GRE.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:16 +0000 (23:49 +0200)]
mlxsw: spectrum_router: Publish mlxsw_sp_l3proto
The spectrum_ipip module that will be introduced in the follow-up
patches needs to know the data type.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:15 +0000 (23:49 +0200)]
mlxsw: reg: Give mlxsw_reg_ratr_pack a type parameter
To support IPIP, the driver needs to be able to construct an IPIP
adjacency. Change mlxsw_reg_ratr_pack to take an adjacency type as an
argument. Adjust the one existing caller.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:14 +0000 (23:49 +0200)]
mlxsw: reg: Extract mlxsw_reg_ritr_mac_pack()
Unlike other interface types, loopback RIFs do not have MAC address. So
drop the corresponding argument from mlxsw_reg_ritr_pack() and move it
to a new function. Call that from callers of mlxsw_reg_ritr_pack.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The RTDP register is used for configuring the tunnel decap properties of
NVE and IPinIP.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To implement IP-in-IP decapsulation, Spectrum uses LPM entries of type
IP2ME with tunnel validity bit and tunnel pointer set. The necessary
register fields are already available, so add a function to pack the
RALUE as appropriate.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:11 +0000 (23:49 +0200)]
mlxsw: reg: Move enum mlxsw_reg_ratr_trap_id
This enum is used with reg_ratr_trap_id, so move it next to the register
definition.
While at it, drop the enumerator initializers.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:10 +0000 (23:49 +0200)]
mlxsw: reg: Update RATR to support IP-in-IP tunnels
So far, adjacencies have always been of type Ethernet (with value of 0),
and thus there was no need to explicitly support RATR type. However to
support IP-in-IP adjacencies, this type and a suite of IP-in-IP-specific
attributes need to be added.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sat, 2 Sep 2017 21:49:09 +0000 (23:49 +0200)]
mlxsw: reg: Update RITR to support loopback device
Update the register so that loopback RIFs can be created and loopback
properties specified.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: dsa: loop: Do not unregister invalid fixed PHY
During error injection it was possible to crash in dsa_loop_exit() because of
an attempt to unregister an invalid PHY. We actually want to the driver probing
in dsa_loop_init() even though fixed_phy_register() may return an error to
exercise how DSA deals with such cases, but we should not be crashing during
driver removal.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: mvpp2: improve the mac address retrieval logic
This series aims at fixing the logic behind the MAC address retrieval in the
PPv2 driver. A possible issue is also fixed in patch 3/3 to introduce fallbacks
when the address given in the device tree isn't valid.
Thanks!
Antoine
Since v2:
- Patch 1/4 from v2 was applied on net (and net was merged in net-next).
- Rebased on net-next.
Since v1:
- Rebased onto net (was on net-next).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Sat, 2 Sep 2017 09:06:49 +0000 (11:06 +0200)]
net: mvpp2: fallback using h/w and random mac if the dt one isn't valid
When using a mac address described in the device tree, a check is made
to see if it is valid. When it's not, no fallback is defined. This
patches tries to get the mac address from h/w (or use a random one if
the h/w one isn't valid) when the dt mac address isn't valid.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Sat, 2 Sep 2017 09:06:48 +0000 (11:06 +0200)]
net: mvpp2: fix use of the random mac address for PPv2.2
The MAC retrieval logic is using a variable to store an h/w stored mac
address and checks this mac against invalid ones before using it. But
the mac address is only read from h/w when using PPv2.1. So when using
PPv2.2 it defaults to its init state.
This patches fixes the logic to only check if the h/w mac is valid when
actually retrieving a mac from h/w.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Sat, 2 Sep 2017 09:06:47 +0000 (11:06 +0200)]
net: mvpp2: move the mac retrieval/copy logic into its own function
The MAC retrieval has a quite complicated logic (which is broken). Moves
it to its own function to prepare for patches fixing its logic, so that
reviews are easier.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 3 Sep 2017 18:04:21 +0000 (11:04 -0700)]
Merge branch 'l2tp-session-creation-fixes'
Guillaume Nault says:
====================
l2tp: session creation fixes
The session creation process has a few issues wrt. concurrent tunnel
deletion.
Patch #1 avoids creating sessions in tunnels that are getting removed.
This prevents races where sessions could try to take tunnel resources
that were already released.
Patch #2 removes some racy l2tp_tunnel_find() calls in session creation
callbacks. Together with path #1 it ensures that sessions can only
access tunnel resources that are guaranteed to remain valid during the
session creation process.
There are other problems with how sessions are created: pseudo-wire
specific data are set after the session is added to the tunnel. So
the session can be used, or deleted, before it has been completely
initialised. Separating session allocation from session registration
would be necessary, but we'd still have circular dependencies
preventing race-free registration. I'll consider this issue in future
series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Using l2tp_tunnel_find() in pppol2tp_session_create() and
l2tp_eth_create() is racy, because no reference is held on the
returned session. These functions are only used to implement the
->session_create callback which is run by l2tp_nl_cmd_session_create().
Therefore searching for the parent tunnel isn't necessary because
l2tp_nl_cmd_session_create() already has a pointer to it and holds a
reference.
This patch modifies ->session_create()'s prototype to directly pass the
the parent tunnel as parameter, thus avoiding searching for it in
pppol2tp_session_create() and l2tp_eth_create().
Since we have to touch the ->session_create() call in
l2tp_nl_cmd_session_create(), let's also remove the useless conditional:
we know that ->session_create isn't NULL at this point because it's
already been checked earlier in this same function.
Finally, one might be tempted to think that the removed
l2tp_tunnel_find() calls were harmless because they would return the
same tunnel as the one held by l2tp_nl_cmd_session_create() anyway.
But that tunnel might be removed and a new one created with same tunnel
Id before the l2tp_tunnel_find() call. In this case l2tp_tunnel_find()
would return the new tunnel which wouldn't be protected by the
reference held by l2tp_nl_cmd_session_create().
Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Fixes: d9e31d17ceba ("l2tp: Add L2TP ethernet pseudowire support") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp: prevent creation of sessions on terminated tunnels
l2tp_tunnel_destruct() sets tunnel->sock to NULL, then removes the
tunnel from the pernet list and finally closes all its sessions.
Therefore, it's possible to add a session to a tunnel that is still
reachable, but for which tunnel->sock has already been reset. This can
make l2tp_session_create() dereference a NULL pointer when calling
sock_hold(tunnel->sock).
This patch adds the .acpt_newsess field to struct l2tp_tunnel, which is
used by l2tp_tunnel_closeall() to prevent addition of new sessions to
tunnels. Resetting tunnel->sock is done after l2tp_tunnel_closeall()
returned, so that l2tp_session_add_to_tunnel() can safely take a
reference on it when .acpt_newsess is true.
The .acpt_newsess field is modified in l2tp_tunnel_closeall(), rather
than in l2tp_tunnel_destruct(), so that it benefits all tunnel removal
mechanisms. E.g. on UDP tunnels, a session could be added to a tunnel
after l2tp_udp_encap_destroy() proceeded. This would prevent the tunnel
from being removed because of the references held by this new session
on the tunnel and its socket. Even though the session could be removed
manually later on, this defeats the purpose of
commit 9980d001cec8 ("l2tp: add udp encap socket destroy handler").
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
net: revert lib/percpu_counter API for fragmentation mem accounting
There is a bug in fragmentation codes use of the percpu_counter API,
that can cause issues on systems with many CPUs, above 24 CPUs.
After much consideration and different attempts at solving the API
usage. The conclusion is to revert to the simple atomic_t API instead.
The ratio between batch size and threshold size make it a bad use-case
for the lib/percpu_counter API. As using the correct API calls will
unfortunately cause systems with many CPUs to always execute an
expensive sum across all CPUs. Plus the added complexity is not worth it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After reverting commit 6d7b857d541e ("net: use lib/percpu_counter API
for fragmentation mem accounting") then here is no need for this
fix-up patch. As percpu_counter is no longer used, it cannot
memory leak it any-longer.
Fixes: 6d7b857d541e ("net: use lib/percpu_counter API for fragmentation mem accounting") Fixes: 1d6119baf061 ("net: fix percpu memory leaks") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug in fragmentation codes use of the percpu_counter API,
that can cause issues on systems with many CPUs.
The frag_mem_limit() just reads the global counter (fbc->count),
without considering other CPUs can have upto batch size (130K) that
haven't been subtracted yet. Due to the 3MBytes lower thresh limit,
this become dangerous at >=24 CPUs (3*1024*1024/130000=24).
The correct API usage would be to use __percpu_counter_compare() which
does the right thing, and takes into account the number of (online)
CPUs and batch size, to account for this and call __percpu_counter_sum()
when needed.
We choose to revert the use of the lib/percpu_counter API for frag
memory accounting for several reasons:
1) On systems with CPUs > 24, the heavier fully locked
__percpu_counter_sum() is always invoked, which will be more
expensive than the atomic_t that is reverted to.
Given systems with more than 24 CPUs are becoming common this doesn't
seem like a good option. To mitigate this, the batch size could be
decreased and thresh be increased.
2) The add_frag_mem_limit+sub_frag_mem_limit pairs happen on the RX
CPU, before SKBs are pushed into sockets on remote CPUs. Given
NICs can only hash on L2 part of the IP-header, the NIC-RXq's will
likely be limited. Thus, a fair chance that atomic add+dec happen
on the same CPU.
Revert note that commit 1d6119baf061 ("net: fix percpu memory leaks")
removed init_frag_mem_limit() and instead use inet_frags_init_net().
After this revert, inet_frags_uninit_net() becomes empty.
Fixes: 6d7b857d541e ("net: use lib/percpu_counter API for fragmentation mem accounting") Fixes: 1d6119baf061 ("net: fix percpu memory leaks") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 31 Aug 2017 17:07:24 +0000 (18:07 +0100)]
net/mlx4_core: fix incorrect size allocation for dev->caps.spec_qps
The current allocation for dev->caps.spec_qps is for the size of the
pointer and not the size of the actual mlx4_spec_qps structure. Fix
this by using the correct size. Also splint allocation over a few
lines to make it cppcheck clean on overly wide lines.
Detected by CoverityScan, CID#1455222 ("Wrong sizeof argument")
Fixes: c73c8b1e47ca ("net/mlx4_core: Dynamically allocate structs at mlx4_slave_cap") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Thu, 31 Aug 2017 16:30:53 +0000 (17:30 +0100)]
net/mlx4_core: fix memory leaks on error exit path
The structures hca_param and func_cap are not being kfree'd on an error
exit path causing two memory leaks. Fix this by jumping to the existing
free memory error exit path.
Detected by CoverityScan, CID#1455219, CID#1455224 ("Resource Leak")
Fixes: c73c8b1e47ca ("net/mlx4_core: Dynamically allocate structs at mlx4_slave_cap") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Brivio [Thu, 31 Aug 2017 16:11:41 +0000 (18:11 +0200)]
ipv4: Don't override return code from ip_route_input_noref()
After ip_route_input() calls ip_route_input_noref(), another
check on skb_dst() is done, but if this fails, we shouldn't
override the return code from ip_route_input_noref(), as it
could have been more specific (i.e. -EHOSTUNREACH).
This also saves one call to skb_dst_force_safe() and one to
skb_dst() in case the ip_route_input_noref() check fails.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com> Fixes: 9df16efadd2a ("ipv4: call dst_hold_safe() properly") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Acked-by: Wei Wang <weiwan@google.com> Acked-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Wed, 7 Jun 2017 10:55:34 +0000 (13:55 +0300)]
net/mlx5e: Distribute RSS table among all RX rings
In default, uniformly distribute the RSS indirection table entries
among all RX rings, rather than restricting this only to the rings
on the close NUMA node. irqbalancer would anyway dynamically override
the default affinities set to the RX rings.
This gives better multi-stream performance and CPU util.
net/mlx5e: Stop NAPI when irq balancer changes affinity
NAPI context keeps rescheduling on same CPU as long as it's busy.
This doesn't give the oppurtunity for changes in irq affinities
to take effect.
Fix that by calling napi_complete_done() upon a change in affinity.
This would stop the NAPI and reschedule it on the new CPU.
net/mlx5e: Use kernel's mechanism to avoid missing NAPIs
We used a channel state bit MLX5E_CHANNEL_NAPI_SCHED to make
sure no NAPI is missed when a channel's napi_schedule() is called
for completion events of the different channel's resources/rings
while NAPI is currently running.
Now, as similar mechanism is implemented in kernel,
("39e6c8208d7b net: solve a NAPI race"),
we obsolete our own implementation and rely on the return value
of napi_complete_done().
This patch removes a redundant overhead of atomic bit operations.