Chen-Yu Tsai [Sun, 15 Dec 2019 16:59:14 +0000 (17:59 +0100)]
media: sun4i-csi: Fix [HV]sync polarity handling
The Allwinner camera sensor interface has a different definition of
[HV]sync. While the timing diagram uses the names HSYNC and VSYNC,
the note following the diagram and register names use HREF and VREF.
Combined they imply the hardware uses either [HV]REF or inverted
[HV]SYNC. There are also registers to set horizontal skip lengths
in pixels and vertical skip lengths in lines, also known as back
porches.
Fix the polarity handling by using the opposite polarity flag for
the checks. Also rename `[hv]sync_pol` to `[hv]ref_pol` to better
match the hardware register description.
Chen-Yu Tsai [Sun, 15 Dec 2019 16:59:13 +0000 (17:59 +0100)]
media: sun4i-csi: Fix data sampling polarity handling
The CLK_POL field specifies whether data is sampled on the falling or
rising edge of PCLK, not whether the data lines are active high or low.
Evidence of this can be found in the timing diagram labeled "horizontal
size setting and pixel clock timing".
Fix the setting by checking the correct flag, V4L2_MBUS_PCLK_SAMPLE_RISING.
While at it, reorder the three polarity flag checks so HSYNC and VSYNC
are grouped together.
Chen-Yu Tsai [Sun, 15 Dec 2019 16:59:12 +0000 (17:59 +0100)]
media: dt-bindings: media: sun4i-csi: Add compatible for CSI0 on R40
The CSI0 block in the Allwinner R40 SoC looks to be the same as the one
in the A20. The register maps line up, and they support the same
features. The R40 appears to support BT.1120 based on the feature
overview, but it is not mentioned anywhere else. Also like the A20, the
ISP is not mentioned, but the CSI special clock needs to be enabled for
the hardware to function. The manual does state that the CSI special
clock is the TOP clock for all CSI hardware, but currently no hardware
exists for us to test if CSI1 also depends on it or not.
Add a compatible string for the CSI0 block in the R40, with the A20
compatible string as a fallback.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <mripard@kernel.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Chen-Yu Tsai [Sun, 15 Dec 2019 16:59:11 +0000 (17:59 +0100)]
media: dt-bindings: media: sun4i-csi: Add compatible for CSI1 on A10/A20
The CSI1 block has the same structure and layout as the CSI0 block.
Differences include:
- Only one channel in BT.656 instead of four in CSI0
- 10-bit raw data input vs 8-bit in CSI0
- 24-bit RGB888/YUV444 input vs 16-bit RGB565/YUV422 in CSI0
- No ISP hardware
The hardware found in the A20 is the same as in the A10.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bingbu Cao [Mon, 30 Dec 2019 09:26:25 +0000 (10:26 +0100)]
media: staging/intel-ipu3: make imgu use fixed running mode
Currently, the imgu running mode need user to set by v4l2 ctrl.
However, imgu only support 2 pipes and 2 operation modes - video and
still. This patch make the first imgu subdev running as video and second
one running as still, it will make the user understand easily, it can
also cover current camera use cases requirement. The running mode is set
during subdev registering, no race-condition after change, so it is safe
to change the mode data type to integer.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bingbu Cao [Mon, 30 Dec 2019 03:09:04 +0000 (04:09 +0100)]
media: staging/intel-ipu3: set the main output as mandatory
From firmware perspective, the main output for each pipe is mandatory
and must be enabled. This patch set the link between imgu subdev and
main output as IMMUTABLE by default.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Thu, 21 Nov 2019 07:55:24 +0000 (08:55 +0100)]
media: i2c: mt9v032: fix enum mbus codes and frame sizes
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adam Ford [Tue, 29 Oct 2019 12:42:11 +0000 (13:42 +0100)]
media: ov5640: Fix check for PLL1 exceeding max allowed rate
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481cad ("media: ov5640: Adjust the clock based on the expected rate") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Adam Ford [Fri, 25 Oct 2019 19:07:23 +0000 (21:07 +0200)]
media: ov5640: Put max framerate into table and simplify check
Currently the various modes are placed into a table, but when
ov5640_find_mode is called, it has to double check whether
or not the requested framerate is tolerated by the mode.
The determination is based on checking hact, vact, and frame rate.
Only 640x480 is allowed at 60fps and QSXGA is limited to 15fps, but
as the number of permitted frame rates change, this will begin to
add more and more complexity to the check.
This patch simplifies the check by adding the max framerate
allowed for each mode into the table of modes. It then compares
the requested framerate to the max permitted in the mode's table.
This reduces the number of comparisions to one down from three
at run-time.
Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Fri, 18 Oct 2019 14:50:05 +0000 (16:50 +0200)]
media: omap3isp: Don't restart CCDC if we're about to stop
The omap3isp driver set the new buffer and enabled the CCDC in a situation
a new buffer was available but streaming was about to be stopped on the
CCDC. This lead to frequent system crashes in case there were buffers
queued when streming was being stopped.
Fix this by first checking whether there's an intent to stop streaming and
if there isn't, then set the new buffer and re-enable CCDC.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sakari Ailus [Thu, 17 Oct 2019 11:01:37 +0000 (13:01 +0200)]
media: omap3isp: Ignore failure of stopping streaming on external subdev
The isp was marked to have failed to stop if stopping streaming on an
external subdev failed. The return value from the external subdev should
be ignored instead as it is not part of the ISP and thus the ISP does not
need to be reset for that reason.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
media: dvb: add support for TerraTec TC2 Stick (193534)
Seems to be a clone of Logilink VG0022A. Supports DVB-C, DVB-T and
DVB-T2. Only terrestrial reception was tested on Polish and Czech
multiplexes.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
These messages happen at random and do not prevent the receiver from
working. Also I cannot change the features of the IC, therefore they are not
useful. Probably they are not useful at all.
However they fill the console, they accumulate and fill the dmesg log, by
doing this, they prevent me from seeing important message.
Signed-off-by: Bodo Eggert <7eggert@gmx.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
James Hogan [Thu, 19 Dec 2019 14:52:57 +0000 (15:52 +0100)]
media: MAINTAINERS: Orphan img-ir driver
I haven't been active for 18 months, and don't have the hardware set up
to test the img-ir driver, so mark it as orphaned and remove myself as
maintainer.
I used to test this driver using a Minimorph board with Meta based
TZ1090 SoC, but the Meta arch port is long gone from the kernel. The
only remaining platform in-tree using this driver is the Imagination
Pistachio SoC, and the only Pistachio based board with DTS in-tree (MIPS
Creator Ci40) doesn't bring the IR out.
However I presume the IP persists under the guardianship of Sondrel, and
its possible current & future SoCs/boards may continue to use this IP.
Signed-off-by: James Hogan <jhogan@kernel.org> Cc: James Hartley <james.hartley@sondrel.com> Cc: Paul Burton <paulburton@kernel.org> Cc: linux-mips@vger.kernel.org Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
David J. Fiddes [Tue, 12 Nov 2019 12:40:59 +0000 (13:40 +0100)]
media: rtl28xxu: Add support for PROlectrix DV107669 DVB-T dongle
This adds support for the PROlectrix DV107669 DVT-T dongle which
uses an RTL2832 and FC0012 tuner.
Tests:
- Verified correct operation of DVB-T reception with VLC across
several UK multiplexes
Signed-off-by: David J. Fiddes <D.J@fiddes.net> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
media: dvb_dummy_fe: Add blank line after declaration
Fix checkpatch.pl error by adding a blank line
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
media: dvb_dummy_fe: place EXPORT_SYMBOL below corresponding function
dvb_dummy_fe.c had all its EXPORT_SYMBOL macros located at the end of the
file. Now these are located directly below the symbol they are exporting
for increased readability.
Suggested-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: stable@vger.kernel.org Tested-by: Nick French <nickfrench@gmail.com> Reported-by: Nick French <nickfrench@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sean Young [Mon, 11 Nov 2019 11:40:52 +0000 (12:40 +0100)]
media: cxusb: use dev_dbg() rather than hand-rolled debug
This solves the following compiler warnings:
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_gpio_tuner’:
drivers/media/usb/dvb-usb/cxusb.c:128:35: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
128 | deb_info("gpio_write failed.\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_bluebird_gpio_rw’:
drivers/media/usb/dvb-usb/cxusb.c:145:44: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
145 | deb_info("bluebird_gpio_write failed.\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c: In function ‘cxusb_i2c_xfer’:
drivers/media/usb/dvb-usb/cxusb.c:251:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
251 | deb_i2c("i2c read may have failed\n");
| ^
drivers/media/usb/dvb-usb/cxusb.c:274:43: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
274 | deb_i2c("i2c write may have failed\n");
| ^
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Arnd Bergmann [Mon, 16 Dec 2019 14:15:06 +0000 (15:15 +0100)]
media: v4l2-core: fix compat v4l2_buffer handling for time64 ABI
Add support for the four new variants of ioctl commands for 64-bit time_t
in v4l2_buffer.
The existing v4l2_buffer32 structure for the traditional format gets
changed to match the new v4l2_buffer format, and the old layout is
now called v4l2_buffer32_time32. Neither of these matches the native
64-bit architecture format of v4l2_buffer, so both require special
handling in compat code.
Duplicating the existing handlers for the new types is a safe conversion
for now, but unfortunately this may turn into a maintenance burden
later. A larger-scale rework of the compat code might be a better
alternative, but is out of scope of the y2038 work.
Note: x32 support for v4l2_buffer32 has always been broken and remains
so after this change, fixing it would have required even more duplication,
and apparently nobody has cared so far.
Arnd Bergmann [Mon, 16 Dec 2019 14:15:05 +0000 (15:15 +0100)]
media: v4l2-core: fix compat VIDIOC_DQEVENT for time64 ABI
The native code supports the variant of struct v4l2_event for 64-bit
time_t, so add the compat version as well.
Here, a new incompatibility arises: while almost all 32-bit architectures
now use the same layout as 64-bit architectures and the commands can
simply be passed through, on x86 the internal alignment of v4l2_event
is different because of the 64-bit member in v4l2_event_ctrl.
To handle all architectures, this now requires defining four different
versions of the structure to cover all possible combinations. The compat
handling for VIDIOC_DQEVENT32 and VIDIOC_DQEVENT32_TIME32 is now inside
of an #ifdef so it does not get used on architectures other than x86.
Arnd Bergmann [Mon, 16 Dec 2019 14:15:04 +0000 (15:15 +0100)]
media: v4l2-core: fix v4l2_buffer handling for time64 ABI
The v4l2_buffer structure contains a 'struct timeval' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
As in v4l2_event, handle this with a special case in video_put_user()
and video_get_user() to replace the memcpy there.
Since the structure also contains a pointer, there are now two
native versions (on 32-bit systems) as well as two compat versions
(on 64-bit systems), which unfortunately complicates the compat
handler quite a bit.
Duplicating the existing handlers for the new types is a safe
conversion for now, but unfortunately this may turn into a
maintenance burden later. A larger-scale rework of the
compat code might be a better alternative, but is out of scope
of the y2038 work.
Sparc64 needs a special case because of their special suseconds_t
definition.
Arnd Bergmann [Mon, 16 Dec 2019 14:15:03 +0000 (15:15 +0100)]
media: v4l2-core: fix VIDIOC_DQEVENT for time64 ABI
The v4l2_event structure contains a 'struct timespec' member that is
defined by the user space C library, creating an ABI incompatibility
when that gets updated to a 64-bit time_t.
While passing a 32-bit time_t here would be sufficient for CLOCK_MONOTONIC
timestamps, simply redefining the structure to use the kernel's
__kernel_old_timespec would not work for any library that uses a copy
of the linux/videodev2.h header file rather than including the copy from
the latest kernel headers.
This means the kernel has to be changed to handle both versions of the
structure layout on a 32-bit architecture. The easiest way to do this
is during the copy from/to user space.
The do_video_ioctl() compat handler converts the compat command
codes into the native ones before processing further, but this
causes problems for 32-bit user applications that pass a command
code that matches a 64-bit native number, which will then be
handled the same way.
Specifically, this breaks VIDIOC_DQEVENT_TIME from user space
applications with 64-bit time_t, as the structure layout is
the same as the native 64-bit layout on many architectures
(x86 being the notable exception).
Change the handler to use the converted command code only for
passing into the native ioctl handler, not for deciding on the
conversion, in order to make the compat behavior match the
native behavior.
Actual support for the 64-bit time_t version of VIDIOC_DQEVENT_TIME
and other commands still needs to be added in a separate patch.
Arnd Bergmann [Mon, 16 Dec 2019 14:15:00 +0000 (15:15 +0100)]
media: v4l2: abstract timeval handling in v4l2_buffer
As a preparation for adding 64-bit time_t support in the uapi,
change the drivers to no longer care about the format of the
timestamp field in struct v4l2_buffer.
The v4l2_timeval_to_ns() function is no longer needed in the
kernel after this, but there is userspace code relying on
it to be part of the uapi header.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: replace spaces by tabs] Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Sun, 15 Dec 2019 11:09:32 +0000 (12:09 +0100)]
media: vivid: support multiplanar touch devices
The v4l2-compliance tests failed with the touch device when multiplanar was
enabled in vivid. Since it is perfectly fine to support the multiplanar API
for touch, add support for this in vivid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Wed, 11 Dec 2019 16:22:27 +0000 (17:22 +0100)]
media: pulse8-cec: move the transmit to a workqueue
Instead of adap_transmit waiting until the full message
is transmitted (and thus hoarding the adap->lock mutex), have it
kick off a transmit workqueue. This prevents adap->lock from
being locked for a very long time.
Also skip FAILED_ACK reports for broadcast messages: this makes
no sense, and it seems a spurious message coming from the
Pulse-Eight, since some time later I see the SUCCEEDED message.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans Verkuil [Wed, 11 Dec 2019 16:22:24 +0000 (17:22 +0100)]
media: pulse8-cec: locking improvements
Drop the write_lock, rename config_lock to plain lock since this
now locks access to the adapter. Use 'lock' when transmitting
a message, ensuring that nothing interferes with the transmit.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
media: v4l2-device.h: Explicitly compare grp{id,mask} to zero in v4l2_device macros
When building with Clang + -Wtautological-constant-compare, several of
the ivtv and cx18 drivers warn along the lines of:
drivers/media/pci/cx18/cx18-driver.c:1005:21: warning: converting the
result of '<<' to a boolean always evaluates to true
[-Wtautological-constant-compare]
cx18_call_hw(cx, CX18_HW_GPIO_RESET_CTRL,
^
drivers/media/pci/cx18/cx18-cards.h:18:37: note: expanded from macro
'CX18_HW_GPIO_RESET_CTRL'
#define CX18_HW_GPIO_RESET_CTRL (1 << 6)
^
1 warning generated.
This warning happens because the shift operation is implicitly converted
to a boolean in v4l2_device_mask_call_all before being negated. This can
be solved by just comparing the mask result to 0 explicitly so that
there is no boolean conversion. The ultimate goal is to enable
-Wtautological-compare globally because there are several subwarnings
that would be helpful to have.
For visual consistency and avoidance of these warnings in the future,
all of the implicitly boolean conversions in the v4l2_device macros
are converted to explicit ones as well.
Ezequiel Garcia [Thu, 5 Dec 2019 14:24:40 +0000 (15:24 +0100)]
media: vidioc-enum-fmt.rst: clarify format preference
It has been decided to use the ENUM_FMT index value
as a hint for driver preference. This is defined purposedly
in a very liberal way, letting drivers define what "preference"
means.
For instance, the Hantro VPU driver indicates additional
processing to output a given format, and thus implicates
more CPU usage, which is enumerated after native (non-processed)
formats.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dragos Bogdan [Fri, 18 Oct 2019 11:29:55 +0000 (13:29 +0200)]
media: adv7604: extend deep color mode to ADV7611
The AD7611 chip supports the same Deep Color Mode settings as the AD7604.
This change extends support for this feature to the AD7611 by adding a
wrapper function for the `read_hdmi_pixelclock` hook and adding the same
frequency adjustment logic.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for the sink pad of scaler subdevice to respond
VIDIOC_G_SELECTION and VIDIOC_S_SELECTION ioctls with the following
targets: V4L2_SEL_TGT_COMPOSE_BOUNDS and V4L2_SEL_TGT_CROP.
* Add new const struct crop_rect_default to initialize subdev scaler
properly.
* Make changes in sink pad format reflect to the crop rectangle. E.g.
changing the frame format to a smaller size one can make the former
crop rectangle selects a non existing frame area. To solve this
situation the crop rectangle is clamped to the frame boundaries.
* Clamp crop rectangle respecting the sink bounds during set_selection
ioctl.
Hans Verkuil [Tue, 19 Nov 2019 10:51:16 +0000 (11:51 +0100)]
media: pixfmt-tch-td16/tu16.rst: document that this is little endian
Testing with the rmi_f54 driver on the Lenovo X1 Carbon 6th gen
laptop showed that the data is in little endian format. Update
the documentation accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rui Miguel Silva [Thu, 12 Dec 2019 19:17:14 +0000 (20:17 +0100)]
media: imx7-mipi-csis: remove subdev_notifier
It was defined a notifier in the csi_state structure that is never
allocated. And besides that it's unregister in the remove, even though
it is a no-op, just remove both.
Fixes: 7807063b862b ("media: staging/imx7: add MIPI CSI-2 receiver subdev for i.MX7") Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Suggested-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org> Reviewed-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hirokazu Honda [Thu, 7 Nov 2019 03:30:57 +0000 (04:30 +0100)]
media: mtk-vcodec: Remove extra area allocation in an input buffer on encoding
MediaTek encoder allocates non pixel data area for an input buffer every
plane. As the input buffer should be read-only, the driver should not write
anything in the buffer. Therefore, the extra data should be unnecessary.
Signed-off-by: Hirokazu Honda <hiroh@chromium.org> Reviewed-by: Tomasz Figa <tfiga@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Fri, 29 Nov 2019 14:10:43 +0000 (15:10 +0100)]
media: atmel: atmel-isi: initialize the try_crop for the pads in try_fmt
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISI was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISI width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Fri, 29 Nov 2019 14:10:38 +0000 (15:10 +0100)]
media: atmel: atmel-isi: add support for mono sensors, GRAY and Y16
This adds support for GREY and Y16 formats, based on Y10 mbus codes.
Y16 needs to go through preview path in the ISI, with 2 pixels per word,
and it fits the Y16 format. The ISI data lines need to be MSB aligned with
the sensor data lines.
GREY format in 8 bits per pixel is done by dropping the 2 LSB bits
from the Y10 format, and packed as 4 pixels per word.
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com> Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Mon, 25 Nov 2019 08:32:54 +0000 (09:32 +0100)]
media: atmel: atmel-isc-base: initialize the try_crop for the pads in try_fmt
When requesting format from sensor, some sensors call the
subdev_get_try_crop which for ISC was not properly initialized, and this
causes errors in determining proper image resolutions.
To accommodate for this, when trying a format (in try_fmt), first attempt
to obtain the framesize for this format from sensor.
In case this fails, use the maximum ISC width/height as try_crop, otherwise
provide the first size height/width from the sensor.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Mon, 25 Nov 2019 08:32:53 +0000 (09:32 +0100)]
media: atmel: atmel-isc-base: fix enum calls default format
With some sensors, the mbus code must match the one that sensor supports.
In this case we should initialize the mbus_code of the fse/fie before
calling the subdev, and not after.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In try_fmt, properly initialize the pad_cfg variable to zeros.
This can be used by various calls from the subdev, so it's better
to have it initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
[hverkuil-cisco@xs4all.nl: changed {0} to {}] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Mon, 25 Nov 2019 08:32:49 +0000 (09:32 +0100)]
media: atmel: atmel-isc-base: add support for Y10 format
The ISC can receive input from sensors using Y10 format directly
(10 bits greyscale). In this case, the ISC must dump the data directly,
either as GREY (8bit) or Y10 (10bit).
Y16 is not supported because we cannot align the MSB 10 bits to the MSB
inside the 16bit container.
For this format, the ISC internal pipeline cannot work (only works with
BAYER), so we must dump the data directly as 8bit/10bit.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Mon, 25 Nov 2019 08:32:48 +0000 (09:32 +0100)]
media: atmel: atmel-isc-base: allow 8 bit direct dump
In case the format that the sensor sends is 8 bit only (like GREY for
example) we need to be able to bypass ISC pipeline and directly dump
8 bits.
That's why the hardcoded value of 16 bpp is not correct in all cases.
This change allows the output format to decide what is the correct bpp
(bits per pixel) such that the result is in the proper format.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Maxime Jourdan [Thu, 5 Dec 2019 15:34:07 +0000 (16:34 +0100)]
media: meson: vdec: add g12a platform
Add support for the G12A platform by:
- adding the G12A codec support, here MPEG1 & MPEG2
- getting the new hevcf clock for the upcoming HEVC/VP9 decoding support
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Philipp Zabel [Thu, 12 Dec 2019 14:23:27 +0000 (15:23 +0100)]
media: coda: avoid hardware lockups with more than 13 capture buffers
When decoding using the CODA internal rotator (for example NV12
capture), currently the value vb2_buf.index + CODA_MAX_FRAMEBUFFERS (19)
is written into the DEC_PIC_ROT_INDEX register. At least with firmware
version 3.1.1 this causes CODA hangups as soon as the register value
reaches 32. Instead, always write CODA_MAX_FRAMEBUFFERS.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Philipp Zabel [Thu, 12 Dec 2019 14:02:55 +0000 (15:02 +0100)]
media: coda: jpeg: add CODA960 JPEG encoder support
This patch adds JPEG encoding support for CODA960, handling the JPEG
hardware directly. A separate JPEG encoder video device is created due
to the separate hardware unit and different supported pixel formats.
While the hardware can not change subsampling on the fly, it can encode
4:2:2 subsampled images into JPEGs of the same subsampling.
There are two additional tracepoints added to the coda driver that can
be used together with the v4l2:v4l2_qbuf and v4l2:v4l2_dqbuf tracepoints
to to follow video frames through the mem2mem device when encoding or
decoding with the CODA960 JPEG codec:
coda:coda_jpeg_run
coda:coda_jpeg_done
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Richard Leitner <richard.leitner@skidata.com>
[hverkuil-cisco@xs4all.nl: removed unused k and q_data_dst variables] Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Philipp Zabel [Thu, 12 Dec 2019 14:02:54 +0000 (15:02 +0100)]
media: coda: jpeg: add JPEG register definitions for CODA960
The CODA960 JPEG codec is controlled directly from the host, there is no
support in the BIT processor firmware. This patch adds the necessary
register definitions.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Philipp Zabel [Thu, 12 Dec 2019 14:02:53 +0000 (15:02 +0100)]
media: coda: jpeg: merge Huffman table bits and values
The Huffman bits tables are always 16 bytes long, and they are always
followed directly by the values tables, both in hardware and in JPEG
files. Just merge the two tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Philipp Zabel [Thu, 12 Dec 2019 14:02:52 +0000 (15:02 +0100)]
media: coda: do not skip finish_run if aborting
Always call finish_run when the hardware signals completion. This
will allow JPEG contexts to clean up even if job_abort was called
during the device_run.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Takashi Iwai [Tue, 10 Dec 2019 13:58:45 +0000 (14:58 +0100)]
media: tm6000: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Also, snd_tm6000_capture_free() is dropped since the check of
stream_started flag makes no sense; hw_free callback is guaranteed to
be called after the stream gets stopped.
Takashi Iwai [Tue, 10 Dec 2019 13:58:44 +0000 (14:58 +0100)]
media: go7007: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Takashi Iwai [Tue, 10 Dec 2019 13:58:43 +0000 (14:58 +0100)]
media: em28xx: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Also, snd_em28xx_hw_capture_free() is dropped since the check of
stream_started flag makes no sense; hw_free callback is guaranteed to
be called after the stream gets stopped.
Takashi Iwai [Tue, 10 Dec 2019 13:58:42 +0000 (14:58 +0100)]
media: cs231xx: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Also, snd_cx231xx_hw_capture_free() is dropped since the check of
stream_started flag makes no sense; hw_free callback is guaranteed to
be called after the stream gets stopped.
Takashi Iwai [Tue, 10 Dec 2019 13:58:41 +0000 (14:58 +0100)]
media: ivtv: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Cc: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Takashi Iwai [Tue, 10 Dec 2019 13:58:40 +0000 (14:58 +0100)]
media: cx18: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Cc: Andy Walls <awalls@md.metrocast.net> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Takashi Iwai [Tue, 10 Dec 2019 13:58:39 +0000 (14:58 +0100)]
media: cobalt: Clean up ALSA PCM API usages
With the recent change in ALSA PCM core, the whole open-coded vmalloc
buffer handling in this driver can be dropped by replacing with the
managed buffer allocation.
Benoit Parrot [Fri, 6 Dec 2019 19:51:32 +0000 (20:51 +0100)]
media: ti-vpe: csc: fix single vs multiplanar format handling
In csc_set_coeff() we were previously checking if the format type was
V4L2_BUF_TYPE_VIDEO_OUTPUT or V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE as a
mean to figure out if the format was multiplanar or not. This was not
entirely accurate as the format type could also be a CAPTURE type
instead.
Fix this by removing the 'switch' construct and replacing them with
"if (V4L2_TYPE_IS_MULTIPLANAR(type))" instead.
Colin Ian King [Wed, 4 Dec 2019 14:11:59 +0000 (15:11 +0100)]
media: meson: add missing allocation failure check on new_buf
Currently if the allocation of new_buf fails then a null pointer
dereference occurs when assiging new_buf->vb. Avoid this by returning
early on a memory allocation failure as there is not much more can
be done at this point.
Addresses-Coverity: ("Dereference null return")
Fixes: 3e7f51bd9607 ("media: meson: add v4l2 m2m video decoder driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
projects / linux.git / log