Sawan Chandak [Wed, 23 Aug 2017 22:05:24 +0000 (15:05 -0700)]
scsi: qla2xxx: Do not call abort handler function during chip reset
If there are IO's running and host reset or chip reset is triggered,
IO's can fail due to rport time out. During chip reset recovery process,
driver notifies the transport layer that remote port no longer exist, by
calling fc_remote_port_delete(). When this function is called, it
actually delays deletion by "blocking" it. It sets the remote port state
to "FC_PORTSTATE_BLOCKED" and sets FC_RPORT_DEVLOSS_PENDING. When
driver tries to abort the command by calling its abort handler function,
abort handler will wait until remote port state is blocked state or wait
for dev_loss_tmo time. Due to this blocking, rport times out and results
in an IO failure. This patch adds a check for any active reset process
before calling abort handler function.
[mkp: typo]
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:22 +0000 (15:05 -0700)]
scsi: qla2xxx: Skip zero queue count entry during FW dump capture
If queue count is zero while reading FW dump template, for entry
T263/T274, skip capturing those entries during FW dump capture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ql2xmaxqdepth is the module parameter that seeds the per target
queue depth in the Scsi midlayer (sdev->queue_depth). Performance
testing revealed that increasing this value would improve IOPS
numbers under certain workloads.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Wed, 23 Aug 2017 22:05:18 +0000 (15:05 -0700)]
scsi: qla2xxx: Cleanup NPIV host in target mode during config teardown
When we tear down the NPIV host configuration in target mode, the
qla_tgt struct was left dangling on the global list. This patch cleans
up link list and frees memory.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:17 +0000 (15:05 -0700)]
scsi: qla2xxx: Add LR distance support from nvram bit
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:15 +0000 (15:05 -0700)]
scsi: qla2xxx: Remove potential macro parameter side-effect in ql_dump_regs()
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:14 +0000 (15:05 -0700)]
scsi: qla2xxx: Print correct mailbox registers in failed summary
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:12 +0000 (15:05 -0700)]
scsi: qla2xxx: Allow SNS fabric login to be retried
If SNS fabric login fails, set loop resync flag to retry via dpc.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:11 +0000 (15:05 -0700)]
scsi: qla2xxx: Add timeout ability to wait_for_sess_deletion().
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:10 +0000 (15:05 -0700)]
scsi: qla2xxx: Move logging default mask to execute once only.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Joe Carnuccio [Wed, 23 Aug 2017 22:05:09 +0000 (15:05 -0700)]
scsi: qla2xxx: Use sp->free instead of hard coded call.
Calling sp->free() ensures the context-correct free routine is called.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Wed, 23 Aug 2017 22:05:07 +0000 (15:05 -0700)]
scsi: qla2xxx: Add ability to autodetect SFP type
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Quinn Tran [Wed, 23 Aug 2017 22:05:05 +0000 (15:05 -0700)]
scsi: qla2xxx: Change ha->wq max_active value to default
Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sawan Chandak [Wed, 23 Aug 2017 22:05:00 +0000 (15:05 -0700)]
scsi: qla2xxx: Handle PCIe error for driver
Driver will perform following
- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
PCI error interface.
- When device is offline, return correct error type from PCIe error
path.
- If there is board disable thread active during shutdown and PCIe
device count is zero then cancel scheduling board disable thread
during shutdown and return.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Darren Trap [Wed, 23 Aug 2017 22:04:59 +0000 (15:04 -0700)]
scsi: qla2xxx: Fix WWPN/WWNN in debug message
Signed-off-by: Darren Trap <darren.trap@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:08 +0000 (04:47 -0700)]
scsi: megaraid_sas: driver version upgrade
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:07 +0000 (04:47 -0700)]
scsi: megaraid_sas: call megasas_dump_frame with correct IO frame size
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:06 +0000 (04:47 -0700)]
scsi: megaraid_sas: modified few prints in OCR and IOC INIT path
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:05 +0000 (04:47 -0700)]
scsi: megaraid_sas: replace internal FALSE/TRUE definitions with false/true
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:04 +0000 (04:47 -0700)]
scsi: megaraid_sas: Return pended IOCTLs with cmd_status MFI_STAT_WRONG_STATE in case adapter is dead
After a kill adapter, since the cmd_status is not set, the IOCTLs will
be hung in driver resulting in application hang. Set cmd_status
MFI_STAT_WRONG_STATE when completing pended IOCTLs.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:03 +0000 (04:47 -0700)]
scsi: megaraid_sas: use vmalloc for crash dump buffers and driver's local RAID map
Driver's local RAID map is accessed frequently. We will first try to get
memory from __get_free_pages. If this fails, fall back to using vmalloc.
For crash dump buffers always prefer vmalloc.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:02 +0000 (04:47 -0700)]
scsi: megaraid_sas: Use SMID for Task abort case only
In TM code, smid_task is valid only in case of task aborts.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:01 +0000 (04:47 -0700)]
scsi: megaraid_sas: Check valid aen class range to avoid kernel panic
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:47:00 +0000 (04:47 -0700)]
scsi: megaraid_sas: Fix endianness issues in DCMD handling
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:46:59 +0000 (04:46 -0700)]
scsi: megaraid_sas: Do not re-fire shutdown DCMD after OCR
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:46:58 +0000 (04:46 -0700)]
scsi: megaraid_sas: Call megasas_complete_cmd_dpc_fusion every 1 second while there are pending commands
megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds. If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:46:57 +0000 (04:46 -0700)]
scsi: megaraid_sas: Use synchronize_irq in target reset case
Similar to task abort case, use synchronize_irq API in target reset
case. Also, remove redundant call to megasas_complete_cmd_dpc_fusion
after calling megasas_sync_irqs in task abort case.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:46:56 +0000 (04:46 -0700)]
scsi: megaraid_sas: set minimum value of resetwaittime to be 1 secs
Setting resetwaittime to 0 during a FW fault will result in driver not
calling the OCR.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S [Wed, 23 Aug 2017 11:46:55 +0000 (04:46 -0700)]
scsi: megaraid_sas: mismatch of allocated MFI frame size and length exposed in MFI MPT pass through command
Driver allocated 256 byte MFI frames bytes but while sending MFI frame
(embedded inside chain frame of MPT frame) to firmware, driver sets the
length as 4k. This results in DMA read error messages during boot.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com> Cc: stable@vger.kernel.org Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: lpfc: remove useless code in lpfc_sli4_bsg_link_diag_test
Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.
Addresses-Coverity-ID: 1226935 Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Todd Poynor [Wed, 16 Aug 2017 05:41:08 +0000 (22:41 -0700)]
scsi: sg: protect against races between mmap() and SG_SET_RESERVED_SIZE
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Todd Poynor [Wed, 16 Aug 2017 04:48:43 +0000 (21:48 -0700)]
scsi: sg: recheck MMAP_IO request length with lock held
Commit 1bc0eb044615 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Thu, 17 Aug 2017 14:44:44 +0000 (17:44 +0300)]
scsi: hpsa: fix the device_id in hpsa_update_device_info()
The parentheses are in the wrong place so we specify the length as
"sizeof(this_device->device_id) < 0" which is zero.
Fixes: 988b87edd231 ("scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arvind Yadav [Wed, 16 Aug 2017 04:59:24 +0000 (10:29 +0530)]
scsi: aha1542: constify pnp_device_id
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-EINVAL will be returned even though the "adapter" argument is perfectly
valid.
Change this so that we only return -EINVAL if the provided string is
invalid. If the host does not implement a ->host_reset function we'll
return -EOPNOTSUPP.
[mkp: tweaked patch description]
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Arvind Yadav [Wed, 16 Aug 2017 04:58:40 +0000 (10:28 +0530)]
scsi: ncr5380: constify pnp_device_id
pnp_device_id are not supposed to change at runtime. All functions
working with pnp_device_id provided by <linux/pnp.h> work with const
pnp_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Acked-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Tue, 15 Aug 2017 17:08:20 +0000 (10:08 -0700)]
scsi: qedf: Fix up modinfo parameter name for 'debug' in modinfo output.
Because we were passing 'qedf_debug' instead of 'debug' to the
MODULE_PARM_DESC() macro, modinfo listed the parameter name as 'qedf_debug'
instead of it's proper name 'debug'. Correct the parameter name.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Tue, 15 Aug 2017 17:08:18 +0000 (10:08 -0700)]
scsi: qedf: Corrent VLAN tag insertion in fallback VLAN case.
Currently in the driver the qedf_ctx attribute vlan_hw_insert is used to
which whether to insert a VLAN tag in FIP frames (except for FIP VLAN
request which is explicitly sent out untagged at least from the driver's
point of view).
When we receive a FIP VLAN response, we set qedf->vlan_hw_insert to 0 which
makes the qedf_fip_send function insert the VLAN. However when we exhaust
our FIP VLAN retries, we do not set qedf->vlan_hw_insert to 0 which means
that the driver will not tag the FIP frame with the correct VLAN ID. The
result that was observed on the wire is that some entity either in the LL2
or L2 firmware is adding a NULL VLAN tag which can cause FIP solicitation
to fail.
The offload FCoE frame function, qedf_xmit, does not use the vlan_hw_insert
attribute to decide whether to tag frames with the FIP/FCoE VLAN. Instead
it unilaterially tags the offload frames with the VLAN ID stored in
qedf->vlan_id. This is the correct behavior so the driver can guarantee
that non-offload FIP frames go out with the correct VLAN ID.
Also use the Linux network layer helpers instead of doing the VLAN insert
manually.
Also fix setting the fallback VLAN so that it used the module parameter and
is not hardcoded to 1002 (though 1002 is the default).
[mkp: fixed typo]
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Tue, 15 Aug 2017 17:08:17 +0000 (10:08 -0700)]
scsi: qedf: Use granted MAC from the FCF for the FCoE source address if it is available.
Currently in the driver we've been using the fc_fcoe_set_mac() function to
set the source MAC for FCoE traffic. This works well in most cases as it
uses the spec. default FCF-MAC. However, if the administrator changes the
FCF-MAC switch, then any FCoE traffic we send will be dropped by the
switch.
Instead we should check the granted MAC from the FLOGI payload and use that
address if it is present. Otherwise, fall back to using the the default
FCF-MAC and the fabric ID of the port as the FCoE MAC address.
Once this address is known we need to set it when doing non-offload
traffic, offload traffic and setting the data_src_address libfcoe uses for
FIP keep alive messages.
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Chad Dupuis [Tue, 15 Aug 2017 17:08:16 +0000 (10:08 -0700)]
scsi: qedf: Set WWNN and WWPN based on values from qed.
If dev_info.wwpn and dev_info.wwnn are set by qed use these values to set
the WWNs of the port. Otherwise fall back to the old method using
fcoe_wwn_from_mac().
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Colin Ian King [Tue, 15 Aug 2017 13:51:45 +0000 (14:51 +0100)]
scsi: mpt3sas: fix pr_info message continuation
An optional discovery status should be printed with a pr_cont and needs
a leading space to make it more readable. The final new line should also
be a pr_cont and the indentation is out by one, so fix that too.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Tue, 15 Aug 2017 06:58:08 +0000 (08:58 +0200)]
scsi: cciss: Drop obsolete driver
The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.
Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Tue, 15 Aug 2017 06:58:07 +0000 (08:58 +0200)]
scsi: hpsa: do not print errors for unsupported report luns format
Legacy boards might not support the 'extended' report luns format,
but as this is to be expected we don't need to print out an error here.
Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Tue, 15 Aug 2017 06:58:06 +0000 (08:58 +0200)]
scsi: hpsa: Ignore errors for unsupported LV_DEVICE_ID VPD page
Legacy boards might not support the LV_DEVICE_ID VPD page, so
we shouldn't print out an error message here.
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Tue, 15 Aug 2017 06:58:05 +0000 (08:58 +0200)]
scsi: hpsa: disable volume status check for legacy boards
Legacy boards might not support volume status, so assume
the volume is online here.
Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Tue, 15 Aug 2017 06:58:04 +0000 (08:58 +0200)]
scsi: hpsa: add support for legacy boards
Add support for legacy boards, ensuring to enable the driver for
those boards only when 'hpsa_allow_any' is set.
The attribute 'legacy_board' is set to '1' if the device is
a legacy board, and '0' otherwise.
Signed-off-by: Hannes Reinecke <hare@suse.com> Acked-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: cxlflash: Fix an error handling path in 'cxlflash_disk_attach()'
'rc' is known to be 0 at this point. If 'create_context()' fails,
returns -ENOMEM instead of 0 which means success.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Helge Deller [Thu, 10 Aug 2017 19:08:49 +0000 (21:08 +0200)]
scsi: sym53c8xx: Avoid undefined behaviour
On parisc I see this UBSAN warning with a sym53c896:
UBSAN: Undefined behaviour in ./drivers/scsi/sym53c8xx_2/sym_hipd.c:762:24
index -1903078336 is out of range for type 'u32 [7]'
Avoid this warning by switching to div64_ul().
[mkp: fix typo]
Signed-off-by: Helge Deller <deller@gmx.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hannes Reinecke [Fri, 11 Aug 2017 06:53:47 +0000 (08:53 +0200)]
scsi: make 'state' device attribute pollable
While the 'state' attribute can (and will) change occasionally,
calling 'poll()' or 'select()' on it fails as sysfs is never
notified that the state has changed.
With this patch calling 'poll()' or 'select()' will work
properly.
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework scsi_internal_device_unblock_nowait() into using a switch
statement. No functional changes.
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with const
pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Acked-by: Bradley Grove <bgrove@attotech.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: virtio: virtio_scsi: Set can_queue to the length of the virtqueue.
Since switching to blk-mq as the default in commit 5c279bd9e406
("scsi: default to scsi-mq"), virtio-scsi LUNs consume about 10x as
much kernel memory.
qemu currently allocates a fixed 128 entry virtqueue. can_queue
currently is set to 1024. But with indirect descriptors, each command
in the queue takes 1 virtqueue entry, so the number of commands which
can be queued is equal to the length of the virtqueue.
Note I intend to send a patch to qemu to allow the virtqueue size to be
configured from the qemu command line.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: virtio: Reduce BUG if total_sg > virtqueue size to WARN.
If using indirect descriptors, you can make the total_sg as large as you
want. If not, BUG is too serious because the function later returns
-ENOSPC.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Manish Rangankar [Thu, 10 Aug 2017 13:32:17 +0000 (06:32 -0700)]
scsi: qedi: Limit number for CQ queues.
[qed_sp_iscsi_func_start:189(host_7-0)]Cannot satisfy CQ amount. Queues
requested 8, CQs available 4. Aborting function start
Above condition will resolve as management firmware is capable of
telling us the number of CQs available for a given PF, qed will
communicate the same number to qedi, So that qedi will know how much CQs
are allowed.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry [Thu, 10 Aug 2017 16:09:43 +0000 (00:09 +0800)]
scsi: hisi_sas: replace kfree with scsi_host_put
Instances of kfree(shost) should be replaced with scsi_host_put().
In addition, a missing scsi_host_put() is added for error path in
hisi_sas_shost_alloc_pci() and v3 driver removal.
Signed-off-by: Pan Bian <bianpan2016@163.com> # For main.c changes Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Thu, 10 Aug 2017 16:09:41 +0000 (00:09 +0800)]
scsi: hisi_sas: add phy_set_linkrate_v3_hw()
Add function to set linkrate for v3 hw.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Thu, 10 Aug 2017 16:09:39 +0000 (00:09 +0800)]
scsi: hisi_sas: update some v3 register init settings
This patch updates some register setting according to recommendation
from HW designer and experiment.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Thu, 10 Aug 2017 16:09:40 +0000 (00:09 +0800)]
scsi: hisi_sas: add reset handler for v3 hw
Use ACPI "_RST" method to reset the controller, since FLR is not
supported.
Function hisi_sas_stop_phys() is introduced to remove some code
duplication.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: qedf: Fix a potential NULL pointer dereference
At the beginning of 'qedf_srr_compl()' and of 'qedf_rec_compl()', we
check if 'orig_io_req' is NULL. If this happens, a NULL pointer
dereference will occur in the error handling path.
Fix it by adding an additional label in the error handling path in order
to avoid this NULL pointer dereference.
[mkp: typo]
Fixes: 61d8658b4a43 ("scsi: qedf: Add QLogic FastLinQ offload FCoE driver framework.") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Chad Dupuis <chad.dupuis@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Dan Carpenter [Thu, 17 Aug 2017 07:09:54 +0000 (10:09 +0300)]
scsi: sg: off by one in sg_ioctl()
If "val" is SG_MAX_QUEUE then we are one element beyond the end of the
"rinfo" array so the > should be >=.
Fixes: 109bade9c625 ("scsi: sg: use standard lists for sg_requests") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Defaulting to scsi-mq in 4.13-rc has shown various regressions
on setups that we didn't previously consider. Fixes for them are
in progress, but too invasive to make it in this cycle. So for
now revert the commit that defaults to blk-mq for SCSI. For 4.14
we'll plan to try again with these fixes.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Damien Le Moal [Wed, 9 Aug 2017 03:00:22 +0000 (12:00 +0900)]
scsi: sd_zbc: Write unlock zone from sd_uninit_cmnd()
Releasing a zone write lock only when the write commnand that acquired
the lock completes can cause deadlocks due to potential command
reordering if the lock owning request is requeued and not executed. This
problem exists only with the scsi-mq path as, unlike the legacy path,
requests are moved out of the dispatch queue before being prepared and
so before locking a zone for a write command.
Since sd_uninit_cmnd() is now always called when a request is requeued,
call sd_zbc_write_unlock_zone() from that function for write requests
that acquired a zone lock instead of from sd_done(). Acquisition of a zone
lock by a write command is indicated using the new command
flag SCMD_ZONE_WRITE_LOCK.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Bart Van Assche <Bart.VanAssche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi: aacraid: Fix out of bounds in aac_get_name_resp
We terminate the aac_get_name_resp on a byte that is outside the bounds
of the structure. Extend the return response by one byte to remove the
out of bounds reference.
Fixes: b836439faf04 ("aacraid: 4KB sector support") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David Carroll <david.carroll@microsemi.com> Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
weiping zhang [Mon, 7 Aug 2017 17:26:57 +0000 (01:26 +0800)]
scsi: megaraid_sas: fix error handle in megasas_probe_one
megasas_mgmt_info.max_index has increased by 1 before megasas_io_attach,
if megasas_io_attach return error, then goto fail_io_attach,
megasas_mgmt_info.instance has a wrong index here. So first reduce
max_index and then set that instance to NULL.
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Thu, 10 Aug 2017 16:09:38 +0000 (00:09 +0800)]
scsi: hisi_sas: kill tasklet when destroying irq in v3 hw
This patch adds calls to kill CQ takslets v3 hw during probe failure.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The channel interrupt is to process all the interrupts except PHY
UP/DOWN and broadcast interrupt. So we need to clear all the interrupts
except those 3 interrupts after processing channel interrupts.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Modify STP link timer from 10ms to 500ms. Also add the register address.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiang Chen [Thu, 10 Aug 2017 16:09:35 +0000 (00:09 +0800)]
scsi: hisi_sas: add status and command buffer for internal abort
For v3 hw, internal abort function required status and command buffer to
be set, so add necessary code for this.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Xiaofei Tan [Thu, 10 Aug 2017 16:09:34 +0000 (00:09 +0800)]
scsi: hisi_sas: support zone management commands
Add two ATA commands, ATA_CMD_ZAC_MGMT_IN and ATA_CMD_ZAC_MGMT_OUT in
hisi_sas_get_ata_protocol(), to support SATA SMR disk.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
projects / linux.git / log