Currently, kmemdup is applied to the firmware data, and it invokes
kmalloc under the hood. The firmware size and patch_length are big (more
than PAGE_SIZE), and on some low-end systems (like ASUS E202SA) kmalloc
may fail to allocate a contiguous chunk under high memory usage and
fragmentation:
Rocky Liao [Thu, 16 Jan 2020 03:22:54 +0000 (11:22 +0800)]
Bluetooth: hci_qca: Enable power off/on support during hci down/up for QCA Rome
This patch registers hdev->shutdown() callback and also sets
HCI_QUIRK_NON_PERSISTENT_SETUP for QCA Rome. It will power-off the BT chip
during hci down and power-on/initialize the chip again during hci up. As
wcn399x already enabled this, this patch also removed the callback register
and QUIRK setting in qca_setup() for wcn399x and uniformly do this in the
probe() routine.
Rocky Liao [Wed, 15 Jan 2020 08:55:51 +0000 (16:55 +0800)]
Bluetooth: hci_qca: Retry btsoc initialize when it fails
This patch adds the retry of btsoc initialization when it fails. There are
reports that the btsoc initialization may fail on some platforms but the
repro ratio is very low. The symptoms is the firmware downloading failed
due to the UART write timed out. The failure may be caused by UART,
platform HW or the btsoc itself but it's very difficlut to root cause,
given the repro ratio is very low. Add a retry for the btsoc initialization
can work around most of the failures and make Bluetooth finally works.
Rocky Liao [Wed, 15 Jan 2020 08:55:50 +0000 (16:55 +0800)]
Bluetooth: hci_qca: Add QCA Rome power off support to the qca_power_shutdown()
Current qca_power_shutdown() only supports wcn399x, this patch adds Rome
power off support to it. For Rome it just needs to pull down the bt_en
GPIO to power off it. This patch also replaces all the power off operation
in qca_close() with the unified qca_power_shutdown() call.
Bluetooth: hci_bcm: enable IRQ capability from devicetree
Add support for getting IRQ directly from DT instead of relying on
converting a GPIO to IRQ. This is needed for platforms with GPIO
controllers that that do not support gpiod_to_irq().
Reviewed-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Alain Michaud [Tue, 7 Jan 2020 00:43:17 +0000 (00:43 +0000)]
Bluetooth: Implementation of MGMT_OP_SET_BLOCKED_KEYS.
MGMT command is added to receive the list of blocked keys from
user-space.
The list is used to:
1) Block keys from being distributed by the device during
the ke distribution phase of SMP.
2) Filter out any keys that were previously saved so
they are no longer used.
Rocky Liao [Mon, 13 Jan 2020 04:30:20 +0000 (12:30 +0800)]
Bluetooth: hci_qca: Add qca_power_on() API to support both wcn399x and Rome power up
This patch adds a unified API qca_power_on() to support both wcn399x and
Rome power on. For wcn399x it calls the qca_wcn3990_init() to init the
regulators, and for Rome it pulls up the bt_en GPIO to power up the btsoc.
It also moves all the power up operation from hdev->open() to
hdev->setup().
YueHaibing [Wed, 8 Jan 2020 01:54:31 +0000 (01:54 +0000)]
Bluetooth: hci_qca: Remove set but not used variable 'opcode'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/bluetooth/hci_qca.c: In function 'qca_controller_memdump':
drivers/bluetooth/hci_qca.c:980:6: warning:
variable 'opcode' set but not used [-Wunused-but-set-variable]
It is never used since commit d841502c79e3 ("Bluetooth: hci_qca: Collect
controller memory dump during SSR"), so remove it.
Colin Ian King [Tue, 7 Jan 2020 18:00:13 +0000 (18:00 +0000)]
Bluetooth: remove redundant assignment to variable icid
Variable icid is being rc is assigned with a value that is never
read. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This enables the code to set the input MTU using the underline link
packet types when set to 0, previously this would likely be rejected by
the remote peer since it would be bellow the minimal of 48 for BR/EDR
or 23 for LE, that way it shall be safe to use 0 without causing any
side effects.
This is convenient for the likes of A2DP transport, see:
https://habr.com/en/post/456182/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: hci_qca: Collect controller memory dump during SSR
We will collect the ramdump of BT controller when hardware error event
received before rebooting the HCI layer. Before restarting a subsystem
or a process running on a subsystem, it is often required to request
either a subsystem or a process to perform proper cache dump and
software failure reason into a memory buffer which application
processor can retrieve afterwards. SW developers can often provide
initial investigation by looking into that debugging information.
Stefan Wahren [Wed, 1 Jan 2020 14:01:34 +0000 (15:01 +0100)]
Bluetooth: hci_bcm: Drive RTS only for BCM43438
The commit 3347a80965b3 ("Bluetooth: hci_bcm: Fix RTS handling during
startup") is causing at least a regression for AP6256 on Orange Pi 3.
So do the RTS line handing during startup only on the necessary platform.
Dmitry Osipenko [Sun, 15 Dec 2019 18:52:52 +0000 (21:52 +0300)]
Bluetooth: hci_bcm: Add device-tree compatible for BCM4329
Driver supports BCM4329, but there is no device-tree compatible for
that chip. Let's add it in order to allow boards to specify Bluetooth
in theirs device-trees, in particular this is useful for NVIDIA Tegra20
boards.
yu kuai [Fri, 3 Jan 2020 12:04:37 +0000 (20:04 +0800)]
bna: remove set but not used variable 'pgoff'
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function
‘bfa_ioc_fwver_clear’:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1127:13: warning: variable
‘pgoff’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver only exists on a non NUMA aware machine.
With 44768decb7c0 ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Xu Wang [Fri, 3 Jan 2020 09:28:16 +0000 (09:28 +0000)]
l2tp: Remove redundant BUG_ON() check in l2tp_pernet
Passing NULL to l2tp_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Xu Wang [Fri, 3 Jan 2020 09:20:40 +0000 (09:20 +0000)]
net: Remove redundant BUG_ON() check in phonet_pernet
Passing NULL to phonet_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
Li RongQing [Fri, 3 Jan 2020 03:51:00 +0000 (11:51 +0800)]
net: remove the check argument from __skb_gro_checksum_convert
The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Fri, 3 Jan 2020 03:48:56 +0000 (03:48 +0000)]
ethtool: remove set but not used variable 'lsettings'
Fixes gcc '-Wunused-but-set-variable' warning:
net/ethtool/linkmodes.c: In function 'ethnl_set_linkmodes':
net/ethtool/linkmodes.c:326:32: warning:
variable 'lsettings' set but not used [-Wunused-but-set-variable]
struct ethtool_link_settings *lsettings;
^
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Po Liu [Thu, 2 Jan 2020 04:59:24 +0000 (04:59 +0000)]
enetc: add support time specific departure base on the qos etf
ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Wed, 1 Jan 2020 07:43:31 +0000 (08:43 +0100)]
ptp: ptp_clockmatrix: constify copied structure
The idtcm_caps structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
tcp: Add support for L3 domains to MD5 auth
With VRF, the scope of network addresses is limited to the L3 domain
the device is associated. MD5 keys are based on addresses, so proper
VRF support requires an L3 domain to be considered for the lookups.
Leverage the new TCP_MD5SIG_EXT option to add support for a device index
to MD5 keys. The __tcpm_pad entry in tcp_md5sig is renamed to tcpm_ifindex
and a new flag, TCP_MD5SIG_FLAG_IFINDEX, in tcpm_flags determines if the
entry is examined. This follows what was done for MD5 and prefixes with
commits 8917a777be3b ("tcp: md5: add TCP_MD5SIG_EXT socket option to set a key address prefix") 6797318e623d ("tcp: md5: add an address prefix for key lookup")
Handling both a device AND L3 domain is much more complicated for the
response paths. This set focuses only on L3 support - requiring the
device index to be an l3mdev (ie, VRF). Support for slave devices can
be added later if desired, much like the progression of support for
sockets bound to a VRF and then bound to a device in a VRF. Kernel
code is setup to explicitly call out that current lookup is for an L3
index, while the uapi just references a device index allowing its
meaning to include other devices in the future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:31 +0000 (14:14 -0800)]
nettest: Add support for TCP_MD5 extensions
Update nettest to implement TCP_MD5SIG_EXT for a prefix and a device.
Add a new option, -m, to specify a prefix and length to use with MD5
auth. The device option comes from the existing -d option. If either
are set and MD5 auth is requested, TCP_MD5SIG_EXT is used instead of
TCP_MD5SIG.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:30 +0000 (14:14 -0800)]
nettest: Return 1 on MD5 failure for server mode
On failure to set MD5 password, do_server should return 1 so that the
program exits with 1 rather than 255. This used for negative testing
when adding MD5 with device option.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:29 +0000 (14:14 -0800)]
net: Add device index to tcp_md5sig
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:28 +0000 (14:14 -0800)]
tcp: Add l3index to tcp_md5sig_key and md5 functions
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:27 +0000 (14:14 -0800)]
ipv4/tcp: Pass dif and sdif to tcp_v4_inbound_md5_hash
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v4_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Mon, 30 Dec 2019 22:14:26 +0000 (14:14 -0800)]
ipv6/tcp: Pass dif and sdif to tcp_v6_inbound_md5_hash
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
mlxsw: Allow setting default port priority
Petr says:
When LLDP APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
This patchset extends the use of the abovementioned APP entry to also set
default port priority (in patches #1 and #2) and then (in patch #3) adds a
selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:29 +0000 (13:48 +0200)]
selftests: mlxsw: Add a self-test for port-default priority
Send non-IP traffic to a port and observe that it gets prioritized
according to the lldptool app=$prio,1,0 rules.
Signed-off-by: Petr Machata <petrm@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:28 +0000 (13:48 +0200)]
mlxsw: spectrum_dcb: Allow setting default port priority
When APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
Extend the use of the abovementioned APP entry to also set default port
priority.
Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Sun, 29 Dec 2019 11:48:27 +0000 (13:48 +0200)]
mlxsw: reg: Add QoS Port DSCP to Priority Mapping Register
Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 2 Jan 2020 23:37:53 +0000 (15:37 -0800)]
Merge branch 'page_pool-NUMA-node-handling-fixes'
Jesper Dangaard Brouer says:
====================
page_pool: NUMA node handling fixes
The recently added NUMA changes (merged for v5.5) to page_pool, it both
contains a bug in handling NUMA_NO_NODE condition, and added code to
the fast-path.
This patchset fixes the bug and moves code out of fast-path. The first
patch contains a fix that should be considered for 5.5. The second
patch reduce code size and overhead in case CONFIG_NUMA is disabled.
Currently the NUMA_NO_NODE setting bug only affects driver 'ti_cpsw'
(drivers/net/ethernet/ti/), but after this patchset, we plan to move
other drivers (netsec and mvneta) to use NUMA_NO_NODE setting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
page_pool: help compiler remove code in case CONFIG_NUMA=n
When kernel is compiled without NUMA support, then page_pool NUMA
config setting (pool->p.nid) doesn't make any practical sense. The
compiler cannot see that it can remove the code paths.
This patch avoids reading pool->p.nid setting in case of !CONFIG_NUMA,
in allocation and numa check code, which helps compiler to see the
optimisation potential. It leaves update code intact to keep API the
same.
page_pool: handle page recycle for NUMA_NO_NODE condition
The check in pool_page_reusable (page_to_nid(page) == pool->p.nid) is
not valid if page_pool was configured with pool->p.nid = NUMA_NO_NODE.
The goal of the NUMA changes in commit d5394610b1ba ("page_pool: Don't
recycle non-reusable pages"), were to have RX-pages that belongs to the
same NUMA node as the CPU processing RX-packet during softirq/NAPI. As
illustrated by the performance measurements.
This patch moves the NAPI checks out of fast-path, and at the same time
solves the NUMA_NO_NODE issue.
First realize that alloc_pages_node() with pool->p.nid = NUMA_NO_NODE
will lookup current CPU nid (Numa ID) via numa_mem_id(), which is used
as the the preferred nid. It is only in rare situations, where
e.g. NUMA zone runs dry, that page gets doesn't get allocated from
preferred nid. The page_pool API allows drivers to control the nid
themselves via controlling pool->p.nid.
This patch moves the NAPI check to when alloc cache is refilled, via
dequeuing/consuming pages from the ptr_ring. Thus, we can allow placing
pages from remote NUMA into the ptr_ring, as the dequeue/consume step
will check the NUMA node. All current drivers using page_pool will
alloc/refill RX-ring from same CPU running softirq/NAPI process.
Drivers that control the nid explicitly, also use page_pool_update_nid
when changing nid runtime. To speed up transision to new nid the alloc
cache is now flushed on nid changes. This force pages to come from
ptr_ring, which does the appropate nid check.
For the NUMA_NO_NODE case, when a NIC IRQ is moved to another NUMA
node, we accept that transitioning the alloc cache doesn't happen
immediately. The preferred nid change runtime via consulting
numa_mem_id() based on the CPU processing RX-packets.
Notice, to avoid stressing the page buddy allocator and avoid doing too
much work under softirq with preempt disabled, the NUMA check at
ptr_ring dequeue will break the refill cycle, when detecting a NUMA
mismatch. This will cause a slower transition, but its done on purpose.
Fixes: d5394610b1ba ("page_pool: Don't recycle non-reusable pages") Reported-by: Li RongQing <lirongqing@baidu.com> Reported-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 Jan 2020 05:43:31 +0000 (21:43 -0800)]
Merge branch '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-12-31
This series contains updates to e1000e, igb and igc only.
Robert Beckett provide an igb change to assist in keeping packets from
being dropped due to receive descriptor ring being full when receive
flow control is enabled. Create a separate function to setup SRRCTL to
ease in reuse and ensure that setting of the drop enable bit only if
receive flow control is not enabled.
Sasha adds support for scatter gather support in igc. Improve the
direct memory address mapping flow by optimizing/simplifying and more
clear. Update igc to use pci_release_mem_regions() instead of
pci_release_selected_regions(). Clean up function header comments to
align with the actual code. Adds support for 64 bit DMA access, to help
handle socket buffer fragments in high memory. Adds legacy power
management support in igc by implementing suspend, resume,
runtime_suspend/resume, and runtime_idle callbacks. Clean up references
to Serdes interface in igc since that interface is not supported for
i225 devices.
Alex replaces the pr_info calls with netdev_info in all cases related to
netdev link state, as suggested by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Thu, 31 Oct 2019 16:58:51 +0000 (09:58 -0700)]
e1000e: Use netdev_info instead of pr_info for link messages
Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.
As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Suggested-by: Joe Perches <joe@perches.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Robert Beckett [Tue, 22 Oct 2019 15:31:41 +0000 (16:31 +0100)]
igb: dont drop packets if rx flow control is enabled
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
Linus Torvalds [Tue, 31 Dec 2019 18:51:27 +0000 (10:51 -0800)]
Merge tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1
Pull tomoyo fixes from Tetsuo Handa:
"Two bug fixes:
- Suppress RCU warning at list_for_each_entry_rcu()
- Don't use fancy names on sockets"
* tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1:
tomoyo: Suppress RCU warning at list_for_each_entry_rcu().
tomoyo: Don't use nifty names on sockets.
Taehee Yoo [Sat, 28 Dec 2019 16:28:09 +0000 (16:28 +0000)]
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
hsr slave interfaces don't have debugfs directory.
So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name
is changed.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1
ip link set dummy0 name ap
Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com Fixes: 4c2d5e33dcd3 ("hsr: rename debugfs file when interface name is changed") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Sat, 28 Dec 2019 15:36:58 +0000 (16:36 +0100)]
net/sched: add delete_empty() to filters and use it in cls_flower
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa194b ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()") Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty") Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vijay Khemka [Fri, 27 Dec 2019 22:43:49 +0000 (14:43 -0800)]
net/ncsi: Fix gma flag setting after response
gma_flag was set at the time of GMA command request but it should
only be set after getting successful response. Movinng this flag
setting in GMA response handler.
This flag is used mainly for not repeating GMA command once
received MAC address.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Kou [Fri, 27 Dec 2019 13:11:16 +0000 (13:11 +0000)]
sctp: add enabled check for path tracepoint loop.
sctp_outq_sack is the main function handles SACK, it is called very
frequently. As the commit "move trace_sctp_probe_path into sctp_outq_sack"
added below code to this function, sctp tracepoint is disabled most of time,
but the loop of transport list will be always called even though the
tracepoint is disabled, this is unnecessary.
+ /* SCTP path tracepoint for congestion control debugging. */
+ list_for_each_entry(transport, transport_list, transports) {
+ trace_sctp_probe_path(transport, asoc);
+ }
This patch is to add tracepoint enabled check at outside of the loop of
transport list, and avoid traversing the loop when trace is disabled,
it is a small optimization.
Signed-off-by: Kevin Kou <qdkevin.kou@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
Improvements to SJA1105 DSA RX timestamping
This series makes the sja1105 DSA driver use a dedicated kernel thread
for RX timestamping, a process which is time-sensitive and otherwise a
bit fragile. This allows users to customize their system (probabil an
embedded PTP switch) fully and allocate the CPU bandwidth for the driver
to expedite the RX timestamps as quickly as possible.
While doing this conversion, add a function to the PTP core for
cancelling this kernel thread (function which I found rather strange to
be missing).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 13:02:30 +0000 (15:02 +0200)]
net: dsa: sja1105: Empty the RX timestamping queue on PTP settings change
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 13:02:28 +0000 (15:02 +0200)]
ptp: introduce ptp_cancel_worker_sync
In order to effectively use the PTP kernel thread for tasks such as
timestamping packets, allow the user control over stopping it, which is
needed e.g. when the timestamping queues must be drained.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cambda Zhu [Fri, 27 Dec 2019 08:52:37 +0000 (16:52 +0800)]
tcp: Fix highest_sack and highest_sack_seq
>From commit 50895b9de1d3 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1d3 ("tcp: highest_sack fix") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladis Dronov [Fri, 27 Dec 2019 02:26:27 +0000 (03:26 +0100)]
ptp: fix the race between the release of ptp_clock and cdev
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u Analyzed-by: Stephen Johnston <sjohnsto@redhat.com> Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:11:13 +0000 (03:11 +0200)]
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:08:07 +0000 (03:08 +0200)]
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
Since commit 86db36a347b4 ("net: dsa: sja1105: Implement state machine
for TAS with PTP clock source"), this paragraph is no longer true. So
remove it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:03:54 +0000 (03:03 +0200)]
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347b4 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 01:01:50 +0000 (03:01 +0200)]
net: dsa: sja1105: Really make the PTP command read-write
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b362 ("net: dsa: sja1105: Make the PTP command read-write") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Dec 2019 00:59:54 +0000 (02:59 +0200)]
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97f5 ("net: dsa: sja1105: Add logic for TX timestamping") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 30 Dec 2019 14:06:19 +0000 (06:06 -0800)]
tcp_cubic: refactor code to perform a divide only when needed
Neal Cardwell suggested to not change ca->delay_min
and apply the ack delay cushion only when Hystart ACK train
is still under consideration. This should avoid a 64bit
divide unless needed.
Tested:
40Gbit(mlx4) testbed (with sch_fq as packet scheduler)
Rahul Lakkireddy [Mon, 30 Dec 2019 12:44:08 +0000 (18:14 +0530)]
cxgb4/cxgb4vf: fix flow control display for auto negotiation
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove #ifdef pollution around nf_ingress(), from Lukas Wunner.
2) Document ingress hook in netdevice, also from Lukas.
3) Remove htons() in tunnel metadata port netlink attributes,
from Xin Long.
4) Missing erspan netlink attribute validation also from Xin Long.
5) Missing erspan version in tunnel, from Xin Long.
6) Missing attribute nest in NFTA_TUNNEL_KEY_OPTS_{VXLAN,ERSPAN}
Patch from Xin Long.
7) Missing nla_nest_cancel() in tunnel netlink dump path,
from Xin Long.
8) Remove two exported conntrack symbols with no clients,
from Florian Westphal.
9) Add nft_meta_get_eval_time() helper to nft_meta, from Florian.
10) Add nft_meta_pkttype helper for loopback, also from Florian.
11) Add nft_meta_socket uid helper, from Florian Westphal.
12) Add nft_meta_cgroup helper, from Florian.
13) Add nft_meta_ifkind helper, from Florian.
14) Group all interface related meta selector, from Florian.
15) Add nft_prandom_u32() helper, from Florian.
16) Add nft_meta_rtclassid helper, from Florian.
17) Add support for matching on the slave device index,
from Florian.
This batch, among other things, contains updates for the netfilter
tunnel netlink interface: This extension is still incomplete and lacking
proper userspace support which is actually my fault, I did not find the
time to go back and finish this. This update is breaking tunnel UAPI in
some aspects to fix it but do it better sooner than never.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 29 Dec 2019 20:29:14 +0000 (12:29 -0800)]
Merge branch 'mlxsw-fixes'
Ido Schimmel says:
====================
mlxsw: Couple of fixes
This patch set contains two fixes for mlxsw. Please consider both for
stable.
Patch #1 from Amit fixes a wrong check during MAC validation when
creating router interfaces (RIFs). Given a particular order of
configuration this can result in the driver refusing to create new RIFs.
Patch #2 fixes a wrong trap configuration in which VRRP packets and
routing exceptions were policed by the same policer towards the CPU. In
certain situations this can prevent VRRP packets from reaching the CPU.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 29 Dec 2019 11:40:23 +0000 (13:40 +0200)]
mlxsw: spectrum: Use dedicated policer for VRRP packets
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Sun, 29 Dec 2019 11:40:22 +0000 (13:40 +0200)]
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>