Jianxin Xiong [Mon, 17 Oct 2016 11:19:41 +0000 (04:19 -0700)]
IB/hfi1: Fix a potential memory leak in hfi1_create_ctxts()
In the function hfi1_create_ctxts the array "dd->rcd" is allocated and
then populated with allocated resources in a loop. Previously, if
error happened during the loop, only resource allocated in the current
iteration would be freed. The array itself would then be freed, leaving
the resources that were allocated in previous iterations and referenced
by the array elements in limbo.
This patch makes sure all allocated resources are freed before freeing
the array "dd->rcd". Also the resource allocation now takes account of
the numa node the device is attached to.
Reviewed-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Tadeusz Struk [Tue, 25 Oct 2016 15:57:55 +0000 (08:57 -0700)]
IB/hfi1: Fix an Oops on pci device force remove
This patch fixes an Oops on device unbind, when the device is used
by a PSM user process. PSM processes access device resources which
are freed on device removal. Similar protection exists in uverbs
in ib_core for Verbs clients, but PSM doesn't use ib_uverbs hence
a separate protection is required for PSM clients.
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: Dean Luick <dean.luick@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
The IRQ affinity entry is not needed after the irq notifier patch has been
added to the hfi1 driver.
The irq affinity settings for SDMA engine should be set using the standard
/proc/irq/<N>/ interface.
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com> Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
IB/rdmavt: rdmavt can handle non aligned page maps
The initial code for rdmavt carried with it a restriction that was a
vestige from the qib driver, that to dma map a page it had to be less
than a page size. This is not the case on modern hardware, both qib and
hfi1 will be just fine with unaligned map requests.
This fixes a 4.8 regression where by an IPoIB transfer of > PAGE_SIZE
will hang because the dma map page call always fails. This was
introduced after commit 5faba5469522 ("IB/ipoib: Report SG feature
regardless of HW UD CSUM capability") added the capability to use SG by
default. Rather than override this, the HW supports it, so allow SG.
Cc: Stable <stable@vger.kernel.org> # 4.8 Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
Linus Torvalds [Sat, 29 Oct 2016 20:42:44 +0000 (13:42 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 bugfix from Thomas Gleixner:
"A single bugfix for the recent changes related to registering the boot
cpu when this has not happened before prefill_possible_map().
The main problem with this change got fixed already, but we missed the
case where the local APIC is not yet mapped, when prefill_possible_map()
is invoked, so the registration of the boot cpu which has the APIC bit
set in CPUID will explode.
I should have seen that issue earlier, but all I can do now is feeling
embarassed"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smpboot: Init apic mapping before usage
Linus Torvalds [Sat, 29 Oct 2016 20:15:24 +0000 (13:15 -0700)]
Merge tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Richard Weinberger:
"This contains fixes for issues in both UBI and UBIFS:
- A regression wrt overlayfs, introduced in -rc2.
- An UBI issue, found by Dan Carpenter's static checker"
* tag 'upstream-4.9-rc3' of git://git.infradead.org/linux-ubifs:
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
Linus Torvalds [Sat, 29 Oct 2016 19:07:29 +0000 (12:07 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We haven't seen a whole lot of fixes for the first two weeks since the
merge window, but here is the batch that we have at the moment.
Nothing sticks out as particularly bad or scary, it's mostly a handful
of smaller fixes to several platforms. The Uniphier reset controller
changes could probably have been delayed to 4.10, but they're not
scary and just plumbing up driver changes that went in during the
merge window.
We're also adding another maintainer to Marvell Berlin platforms, to
help out when Sebastian is too busy. Yay teamwork!"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Updated NAND DT properties for NS2 SVK
arm64: dts: uniphier: change MIO node to SD control node
ARM: dts: uniphier: change MIO node to SD control node
reset: uniphier: rename MIO reset to SD reset for Pro5, PXs2, LD20 SoCs
arm64: uniphier: select ARCH_HAS_RESET_CONTROLLER
ARM: uniphier: select ARCH_HAS_RESET_CONTROLLER
arm64: dts: Add timer erratum property for LS2080A and LS1043A
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
ARM: multi_v7_defconfig: Enable Intel e1000e driver
MAINTAINERS: add myself as Marvell berlin SoC maintainer
bus: qcom-ebi2: depend on ARCH_QCOM or COMPILE_TEST
ARM: dts: fix the SD card on the Snowball
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Linus Torvalds [Sat, 29 Oct 2016 18:19:02 +0000 (11:19 -0700)]
Merge tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small char/misc driver fixes for reported issues.
The "biggest" are two binder fixes for reported issues that have been
shipping in Android phones for a while now, the others are various
fixes for reported problems.
And there's a MAINTAINERS update for good measure.
All have been in linux-next with no reported issues"
* tag 'char-misc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
extcon: qcom-spmi-misc: Sync the extcon state on interrupt
hv: do not lose pending heartbeat vmbus packets
mei: txe: don't clean an unprocessed interrupt cause.
ANDROID: binder: Clear binder and cookie when setting handle in flat binder struct
ANDROID: binder: Add strong ref checks
Olof Johansson [Sat, 29 Oct 2016 18:09:37 +0000 (11:09 -0700)]
Merge tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Olof Johansson [Sat, 29 Oct 2016 18:09:11 +0000 (11:09 -0700)]
Merge tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux into fixes
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Olof Johansson [Sat, 29 Oct 2016 18:08:50 +0000 (11:08 -0700)]
Merge tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec670763dd
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e0c ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Linus Torvalds [Sat, 29 Oct 2016 17:57:40 +0000 (10:57 -0700)]
Merge tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core / kernfs fixes for 4.9-rc3.
One makes the Kconfig entry for DEBUG_TEST_DRIVER_REMOVE a bit more
explicit that this is a crazy thing to enable for a distro kernel
(thanks for trying Fedora!), the other resolves an issue with vim
opening kernfs files (sysfs, configfs, etc.)
Both have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Make Kconfig text for DEBUG_TEST_DRIVER_REMOVE stronger
kernfs: Add noop_fsync to supported kernfs_file_fops
Linus Torvalds [Sat, 29 Oct 2016 17:20:59 +0000 (10:20 -0700)]
Merge tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small staging and iio driver fixes for reported issues
for 4.9-rc3. Nothing major, the "largest" being a lustre fix for a
sysfs file that was obviously wrong, and had never been tested, so it
was moved to debugfs as that is where it belongs. The others are small
bug fixes for reported issues with various staging or iio drivers.
All have been in linux-next for a while with no reported issues"
* tag 'staging-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
greybus: fix a leak on error in gb_module_create()
greybus: es2: fix error return code in ap_probe()
greybus: arche-platform: Add missing of_node_put() in arche_platform_change_state()
staging: android: ion: Fix error handling in ion_query_heaps()
iio: accel: sca3000_core: avoid potentially uninitialized variable
iio:chemical:atlas-ph-sensor: Fix use of 32 bit int to hold 16 bit big endian value
staging/lustre/llite: Move unstable_stats from sysfs to debugfs
Staging: wilc1000: Fix kernel Oops on opening the device
staging: android/ion: testing the wrong variable
Staging: greybus: uart: Use gbphy_dev->dev instead of bundle->dev
Staging: greybus: gpio: Use gbphy_dev->dev instead of bundle->dev
iio: adc: ti-adc081c: Select IIO_TRIGGERED_BUFFER to prevent build errors
iio: maxim_thermocouple: Align 16 bit big endian value of raw reads
Linus Torvalds [Sat, 29 Oct 2016 17:17:52 +0000 (10:17 -0700)]
Merge tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty and serial driver fixes for reported
issues for 4.9-rc3. Nothing major, but they do resolve a bunch of
problems with the tty core changes that are in 4.9-rc1, and finally
the atmel serial driver is back working properly.
All have been in linux-next with no reported issues"
* tag 'tty-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
tty: serial_core: Fix serial console crash on port shutdown
tty/serial: at91: fix hardware handshake on Atmel platforms
vt: clear selection before resizing
sc16is7xx: always write state when configuring GPIO as an output
sh-sci: document R8A7743/5 support
tty: serial: 8250: 8250_core: NXP SC16C2552 workaround
tty: limit terminal size to 4M chars
tty: serial: fsl_lpuart: Fix Tx DMA edge case
serial: 8250_lpss: enable MSI for sure
serial: core: fix console problems on uart_close
serial: 8250_uniphier: fix clearing divisor latch access bit
serial: 8250_uniphier: fix more unterminated string
serial: pch_uart: add terminate entry for dmi_system_id tables
devicetree: bindings: uart: Add new compatible string for ZynqMP
serial: xuartps: Add new compatible string for ZynqMP
serial: SERIAL_STM32 should depend on HAS_DMA
serial: stm32: Fix comparisons with undefined register
tty: vt, fix bogus division in csi_J
Thomas Gleixner [Sat, 29 Oct 2016 11:42:42 +0000 (13:42 +0200)]
x86/smpboot: Init apic mapping before usage
The recent changes, which forced the registration of the boot cpu on UP
systems, which do not have ACPI tables, have been fixed for systems w/o
local APIC, but left a wreckage for systems which have neither ACPI nor
mptables, but the CPU has an APIC, e.g. virtualbox.
The boot process crashes in prefill_possible_map() as it wants to register
the boot cpu, which needs to access the local apic, but the local APIC is
not yet mapped.
There is no reason why init_apic_mapping() can't be invoked before
prefill_possible_map(). So instead of playing another silly early mapping
game, as the ACPI/mptables code does, we just move init_apic_mapping()
before the call to prefill_possible_map().
In hindsight, I should have noticed that combination earlier.
Sorry for the churn (also in stable)!
Fixes: ff8560512b8d ("x86/boot/smp: Don't try to poke disabled/non-existent APIC") Reported-and-debugged-by: Michal Necasek <michal.necasek@oracle.com> Reported-and-tested-by: Wolfgang Bauer <wbauer@tmo.at> Cc: prarit@redhat.com Cc: ville.syrjala@linux.intel.com Cc: michael.thayer@oracle.com Cc: knut.osmundsen@oracle.com Cc: frank.mehnert@oracle.com Cc: Borislav Petkov <bp@alien8.de> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1610282114380.5053@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linus Torvalds [Sat, 29 Oct 2016 01:34:19 +0000 (18:34 -0700)]
Merge tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix recent ACPICA regressions, an older PCI IRQ management
regression, and an incorrect return value of a function in the APEI
code.
Specifics:
- Fix three ACPICA issues related to the interpreter locking and
introduced by recent changes in that area (Lv Zheng).
- Fix a PCI IRQ management regression introduced during the 4.7 cycle
and related to the configuration of shared IRQs on systems with an
ISA bus (Sinan Kaya).
- Fix up a return value of one function in the APEI code (Punit
Agrawal)"
* tag 'acpi-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ACPI / APEI: Fix incorrect return value of ghes_proc()
ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
ACPI/PCI: pci_link: penalize SCI correctly
ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages
Linus Torvalds [Sat, 29 Oct 2016 01:29:13 +0000 (18:29 -0700)]
Merge tag 'pm-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two intel_pstate issues related to the way it works when the
scaling_governor sysfs attribute is set to "performance" and fix up
messages in the system suspend core code.
Specifics:
- Fix a missing KERN_CONT in a system suspend message by converting
the affected code to using pr_info() and pr_cont() instead of the
"raw" printk() (Jon Hunter).
- Make intel_pstate set the CPU P-state from its .set_policy()
callback when the scaling_governor sysfs attribute is set to
"performance" so that it interacts with NOHZ_FULL more predictably
which was the case before 4.7 (Rafael Wysocki).
- Make intel_pstate always request the maximum allowed P-state when
the scaling_governor sysfs attribute is set to "performance" to
prevent it from effectively ingoring that setting is some
situations (Rafael Wysocki)"
* tag 'pm-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Always set max P-state in performance mode
PM / suspend: Fix missing KERN_CONT for suspend message
cpufreq: intel_pstate: Set P-state upfront in performance mode
Linus Torvalds [Sat, 29 Oct 2016 00:02:58 +0000 (17:02 -0700)]
Merge tag 'arc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- support IDU intc for UP builds
- support gz, lzma compressed uImage [Daniel Mentz]
- adjust /proc/cpuinfo for non-continuous cpu ids [Noam Camus]
- syscall for userspace cmpxchg assist for configs lacking hardware atomics
- rework of boot log printing mainly for identifying older arc700 cores
- retiring some old code, build toggles
* tag 'arc-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ARCv2: IOC: use @ioc_enable not @ioc_exist where intended
ARC: syscall for userspace cmpxchg assist
ARC: fix build warning in elf.h
ARC: Adjust cpuinfo for non-continuous cpu ids
ARC: [build] Support gz, lzma compressed uImage
ARCv2: intc: untangle SMP, MCIP and IDU
Merge branches 'acpica-fixes', 'acpi-pci-fixes' and 'acpi-apei-fixes'
* acpica-fixes:
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
* acpi-pci-fixes:
ACPI/PCI: pci_link: Include PIRQ_PENALTY_PCI_USING for ISA IRQs
ACPI/PCI: pci_link: penalize SCI correctly
ACPI/PCI/IRQ: assign ISA IRQ directly during early boot stages
* acpi-apei-fixes:
ACPI / APEI: Fix incorrect return value of ghes_proc()
Lv Zheng [Wed, 26 Oct 2016 07:42:01 +0000 (15:42 +0800)]
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
In the code path of acpi_ev_initialize_region(), there is namespace
modification code unlocked. This patch tunes the code to make sure
such modification are always locked.
Fixes: 74f51b80a0c4 (ACPICA: Namespace: Fix dynamic table loading issues) Tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Wed, 26 Oct 2016 07:40:20 +0000 (15:40 +0800)]
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
There is a lock unbalanced exit path in acpi_ds_initialize_method(),
this patch corrects it.
Fixes: 441ad11d078f (ACPICA: Dispatcher: Fix a mutex issue for method auto serialization) Tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Lv Zheng [Wed, 26 Oct 2016 07:40:12 +0000 (15:40 +0800)]
ACPICA: Dispatcher: Fix order issue of method termination
The last step of the method termination should be the end of the method
serialization. Otherwise, the steps happening after it will face the race
issues that cannot be protected by the method serialization mechanism.
This patch fixes this issue by moving the per-method-object deletion code
prior than the end of the method serialization. Otherwise, the possible
race issues may result in AE_ALREADY_EXISTS error in a parallel
environment.
Fixes: 74f51b80a0c4 (ACPICA: Namespace: Fix dynamic table loading issues) Reported-and-tested-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Fri, 28 Oct 2016 23:52:28 +0000 (16:52 -0700)]
Merge tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Convert cmp to cmpd in idle enter sequence (Segher Boessenkool)
- cxl: Fix leaking pid refs in some error paths (Vaibhav Jain)
- Re-fix race condition between going idle and entering guest (Paul Mackerras)
- Fix race condition in setting lock bit in idle/wakeup code (Paul Mackerras)
- radix: Use tlbiel only if we ever ran on the current cpu (Aneesh Kumar K.V)
- relocation, register save fixes for system reset interrupt (Nicholas Piggin)
Fixes for code merged this cycle:
- Fix CONFIG_ALIVEC typo in restore_tm_state() (Valentin Rothberg)
- KVM: PPC: Book3S HV: Fix build error when SMP=n (Michael Ellerman)"
* tag 'powerpc-4.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: relocation, register save fixes for system reset interrupt
powerpc/mm/radix: Use tlbiel only if we ever ran on the current cpu
powerpc/process: Fix CONFIG_ALIVEC typo in restore_tm_state()
powerpc/64: Fix race condition in setting lock bit in idle/wakeup code
powerpc/64: Re-fix race condition between going idle and entering guest
cxl: Fix leaking pid refs in some error paths
powerpc: Convert cmp to cmpd in idle enter sequence
KVM: PPC: Book3S HV: Fix build error when SMP=n
Linus Torvalds [Fri, 28 Oct 2016 23:27:16 +0000 (16:27 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc kernel fixes: a virtualization environment related fix, an uncore
PMU driver removal handling fix, a PowerPC fix and new events for
Knights Landing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
perf/powerpc: Don't call perf_event_disable() from atomic context
perf/core: Protect PMU device removal with a 'pmu_bus_running' check, to fix CONFIG_DEBUG_TEST_DRIVER_REMOVE=y kernel panic
perf/x86/intel/cstate: Add C-state residency events for Knights Landing
Linus Torvalds [Fri, 28 Oct 2016 18:47:45 +0000 (11:47 -0700)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A build fix, a NULL de-reference found by static analysis, a misuse of
the percpu_ref_exit() (tagged for -stable), and notification of failed
attempts to clear media errors.
These patches have received a build success notification from the
0day- kbuild-robot and appeared in next-20161028"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix percpu_ref_exit ordering
nvdimm: make CONFIG_NVDIMM_DAX 'bool'
pmem: report error on clear poison failure
libnvdimm, namespace: potential NULL deref on allocation error
Linus Torvalds [Fri, 28 Oct 2016 18:31:06 +0000 (11:31 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes for -rc3. They're all pretty straightforward: a
couple of NUMA issues from the Huawei folks and a thinko in
__page_to_voff that seems to be benign, but is certainly better off
fixed.
Summary:
- couple of NUMA fixes
- thinko in __page_to_voff"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: fix __page_to_voff definition
arm64/numa: fix incorrect log for memory-less node
arm64/numa: fix pcpu_cpu_distance() to get correct CPU proximity
Linus Torvalds [Fri, 28 Oct 2016 18:26:01 +0000 (11:26 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Fix four timer locking races: two were noticed by Linus while
reviewing the code while chasing for a corruption bug, and two
from fixing spurious USB timeouts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Prevent base clock corruption when forwarding
timers: Prevent base clock rewind when forwarding clock
timers: Lock base for same bucket optimization
timers: Plug locking race vs. timer migration
Linus Torvalds [Fri, 28 Oct 2016 17:12:27 +0000 (10:12 -0700)]
Merge branches 'core-urgent-for-linus', 'irq-urgent-for-linus' and 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool, irq and scheduler fixes from Ingo Molnar:
"One more objtool fixlet for GCC6 code generation patterns, an irq
DocBook fix and an unused variable warning fix in the scheduler"
Vineet Gupta [Tue, 25 Oct 2016 17:43:20 +0000 (10:43 -0700)]
ARC: module: elide loop to save reference to .eh_frame
The loop was really needed in .debug_frame regime where wanted make it
as SH_ALLOC so that apply_relocate_add() would process it. That's not
needed for .eh_frame, so we check this in apply_relocate_add() which
gets called for each section.
Note that we need to save reference to "section name strings" section in
module_frob_arch_sections() since apply_relocate_add() doesn't get that
Vineet Gupta [Thu, 27 Oct 2016 21:33:19 +0000 (14:33 -0700)]
ARC: boot log: refactor cpu name/release printing
The motivation is to identify ARC750 vs. ARC770 (we currently print
generic "ARC700").
A given ARC700 release could be 750 or 770, with same ARCNUM (or family
identifier which is unfortunate). The existing arc_cpu_tbl[] kept a single
concatenated string for core name and release which thus doesn't work
for 750 vs. 770 identification.
So split this into 2 tables, one with core names and other with release.
And while we are at it, get rid of the range checking for family numbers.
We just document the known to exist cores running Linux and ditch
others.
With this in place, we add detection of ARC750 which is
- cores 0x33 and before
- cores 0x34 and later with MMUv2
Vineet Gupta [Fri, 21 Oct 2016 01:08:10 +0000 (18:08 -0700)]
ARC: boot log: don't assume SWAPE instruction support
This came to light when helping a customer with oldish ARC750 core who
were getting instruction errors because of lack of SWAPE but boot log
was incorrectly printing it as being present
Vineet Gupta [Fri, 21 Oct 2016 00:49:15 +0000 (17:49 -0700)]
ARC: boot log: refactor printing abt features not captured in BCRs
On older arc700 cores, some of the features configured were not present
in Build config registers. To print about them at boot, we just use the
Kconfig option i.e. whether linux is built to use them or not.
So yes this seems bogus, but what else can be done. Moreover if linux is
booting with these enabled, then the Kconfig info is a good indicator
anyways.
Over time these "hacks" accumulated in read_arc_build_cfg_regs() as well
as arc_cpu_mumbojumbo(). so refactor and move all of those in a single
place: read_arc_build_cfg_regs(). This causes some code redcution too:
Linus Torvalds [Fri, 28 Oct 2016 17:07:35 +0000 (10:07 -0700)]
Merge branch 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"My patch fixes the btrfs list_head abuse that we tracked down during
Dave Jones' memory corruption investigation. With both Jens and my
patches in place, I'm no longer able to trigger problems.
Filipe is fixing a difficult old bug between snapshots, balance and
send. Dave is cooking a few more for the next rc, but these are tested
and ready"
* 'for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: fix races on root_log_ctx lists
btrfs: fix incremental send failure caused by balance
Linus Torvalds [Fri, 28 Oct 2016 17:00:44 +0000 (10:00 -0700)]
Merge tag 'sound-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains the usual stuff -- the fixups and quirks for HD-audio
and USB-audio, in addition to a bad regression fix in ALSA sequencer
timer since 4.8, and a trivial fix for asihpi PCI driver"
* tag 'sound-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Add quirk for Syntek STK1160
ALSA: seq: Fix time account regression
ALSA: hda - Fix surround output pins for ASRock B150M mobo
ALSA: hda - Fix headset mic detection problem for two Dell laptops
ALSA: asihpi: fix kernel memory disclosure
ALSA: hda - Adding a new group of pin cfg into ALC295 pin quirk table
ALSA: hda - allow 40 bit DMA mask for NVidia devices
Linus Torvalds [Fri, 28 Oct 2016 16:36:07 +0000 (09:36 -0700)]
Merge tag 'drm-x86-pat-regression-fix' of git://people.freedesktop.org/~airlied/linux
Pull drm x86/pat regression fixes from Dave Airlie:
"This is a standalone pull request for the fix for a regression
introduced in -rc1 by a change to vm_insert_mixed to start using the
PAT range tracking to validate page protections. With this fix in
place, all the VRAM mappings for GPU drivers ended up at UC instead of
WC.
There are probably better ways to fix this long term, but nothing I'd
considered for -fixes that wouldn't need more settling in time. So
I've just created a new arch API that the drivers can reserve all
their VRAM aperture ranges as WC"
* tag 'drm-x86-pat-regression-fix' of git://people.freedesktop.org/~airlied/linux:
drm/drivers: add support for using the arch wc mapping API.
x86/io: add interface to reserve io memtype for a resource range. (v1.1)
Linus Torvalds [Fri, 28 Oct 2016 16:27:58 +0000 (09:27 -0700)]
Merge tag 'dm-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a couple DM raid and DM mirror fixes
- a couple .request_fn request-based DM NULL pointer fixes
- a fix for a DM target reference count leak, on target load error,
that prevented associated DM target kernel module(s) from being
removed
* tag 'dm-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: fix missing dm_put_target_type() in dm_table_add_target()
dm rq: clear kworker_task if kthread_run() returned an error
dm: free io_barrier after blk_cleanup_queue call
dm raid: fix activation of existing raid4/10 devices
dm mirror: use all available legs on multiple failures
dm mirror: fix read error on recovery after default leg failure
dm raid: fix compat_features validation
Linus Torvalds [Fri, 28 Oct 2016 16:23:59 +0000 (09:23 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull key fixes from James Morris:
- fix a buffer overflow when displaying /proc/keys [CVE-2016-7042].
- fix broken initialisation in the big_key implementation that can
result in an oops.
- make big_key depend on having a random number generator available in
Kconfig.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security/keys: make BIG_KEYS dependent on stdrng.
KEYS: Sort out big_key initialisation
KEYS: Fix short sprintf buffer in /proc/keys show function
Commit c83ed4c9dbb35 ("ubifs: Abort readdir upon error") broke
overlayfs support because the fix exposed an internal error
code to VFS.
Reported-by: Peter Rosin <peda@axentia.se> Tested-by: Peter Rosin <peda@axentia.se> Reported-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Tested-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Fixes: c83ed4c9dbb35 ("ubifs: Abort readdir upon error") Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at>
Boris Brezillon [Fri, 28 Oct 2016 09:08:44 +0000 (11:08 +0200)]
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
Commit e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already
exists") introduced a bug by changing the possible error codes returned
by add_vol():
- this function no longer returns NULL in case of allocation failure
but return ERR_PTR(-ENOMEM)
- when a duplicate entry in the volume RB tree is found it returns
ERR_PTR(-EEXIST) instead of ERR_PTR(-EINVAL)
Fix the tests done on add_vol() return val to match this new behavior.
Fixes: e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already exists") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at>
Jorgen Hansen [Thu, 6 Oct 2016 11:43:08 +0000 (04:43 -0700)]
VMCI: Doorbell create and destroy fixes
This change consists of two changes:
1) If vmci_doorbell_create is called when neither guest nor
host personality as been initialized, vmci_get_context_id
will return VMCI_INVALID_ID. In that case, we should fail
the create call.
2) In doorbell destroy, we assume that vmci_guest_code_active()
has the same return value on create and destroy. That may not
be the case, so we may end up with the wrong refcount.
Instead, destroy should check explicitly whether the doorbell
is in the index table as an indicator of whether the guest
code was active at create time.
Gerald Schaefer [Wed, 19 Oct 2016 10:29:41 +0000 (12:29 +0200)]
GenWQE: Fix bad page access during abort of resource allocation
When interrupting an application which was allocating DMAable
memory, it was possible, that the DMA memory was deallocated
twice, leading to the error symptoms below.
Thanks to Gerald, who analyzed the problem and provided this
patch.
I agree with his analysis of the problem: ddcb_cmd_fixups() ->
genwqe_alloc_sync_sgl() (fails in f/lpage, but sgl->sgl != NULL
and f/lpage maybe also != NULL) -> ddcb_cmd_cleanup() ->
genwqe_free_sync_sgl() (double free, because sgl->sgl != NULL and
f/lpage maybe also != NULL)
In this scenario we would have exactly the kind of double free that
would explain the WARNING / Bad page state, and as expected it is
caused by broken error handling (cleanup).
Using the Ubuntu git source, tag Ubuntu-4.4.0-33.52, he was able to reproduce
the "Bad page state" issue, and with the patch on top he could not reproduce
it any more.
Rob Herring [Fri, 28 Oct 2016 12:07:48 +0000 (07:07 -0500)]
tty: serial_core: fix NULL struct tty pointer access in uart_write_wakeup
Since commit 761ed4a94582ab29 ("tty: serial_core: convert uart_close to
use tty_port_close"), the serial console is broken on various systems
and typing "reboot" splats the following on the serial console:
The problem is for console ports, the serial port is not shutdown and
interrupts may fire after the struct tty is gone. Simply calling the
tty_port helper tty_port_tty_wakeup instead of tty_wakeup directly will
ensure there is a valid struct tty.
Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Borislav Petkov <bp@alien8.de> Reported-by: Mike Galbraith <mgalbraith@suse.de> Cc: Jiri Slaby <jslaby@suse.cz> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-serial@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: serial_core: Fix serial console crash on port shutdown
The port->console flag is always false, as uart_console() is called
before the serial console has been registered.
Hence for a serial port used as the console, uart_tty_port_shutdown()
will still be called when userspace closes the port, powering it down.
This may lead to a system lock up when the serial console driver writes
to the serial port's registers.
To fix this, move the setting of port->console after the call to
uart_configure_port(), which registers the serial console.
Fixes: 761ed4a94582ab29 ("tty: serial_core: convert uart_close to use tty_port_close") Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Rob Herring <robh@kernel.org> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[robh: rebased on tty-linus] Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Genoud [Thu, 27 Oct 2016 16:04:06 +0000 (18:04 +0200)]
tty/serial: at91: fix hardware handshake on Atmel platforms
After commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), the hardware handshake wasn't
functional anymore on Atmel platforms (beside SAMA5D2).
To understand why, one has to understand the flag ATMEL_US_USMODE_HWHS
first:
Before commit 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management
when hardware handshake is enabled"), this flag was never set.
Thus, the CTS/RTS where only handled by serial_core (and everything
worked just fine).
This commit introduced the use of the ATMEL_US_USMODE_HWHS flag,
enabling it for all boards when the user space enables flow control.
When the ATMEL_US_USMODE_HWHS is set, the Atmel USART controller
handles a part of the flow control job:
- disable the transmitter when the CTS pin gets high.
- drive the RTS pin high when the DMA buffer transfer is completed or
PDC RX buffer full or RX FIFO is beyond threshold. (depending on the
controller version).
NB: This feature is *not* mandatory for the flow control to work.
(Nevertheless, it's very useful if low latencies are needed.)
Now, the specifics of the ATMEL_US_USMODE_HWHS flag:
- For platforms with DMAC and no FIFOs (sam9x25, sam9x35, sama5D3,
sama5D4, sam9g15, sam9g25, sam9g35)* this feature simply doesn't work.
( source: https://lkml.org/lkml/2016/9/7/598 )
Tested it on sam9g35, the RTS pins always stays up, even when RXEN=1
or a new DMA transfer descriptor is set.
=> ATMEL_US_USMODE_HWHS must not be used for those platforms
- For platforms with a PDC (sam926{0,1,3}, sam9g10, sam9g20, sam9g45,
sam9g46)*, there's another kind of problem. Once the flag
ATMEL_US_USMODE_HWHS is set, the RTS pin can't be driven anymore via
RTSEN/RTSDIS in USART Control Register. The RTS pin can only be driven
by enabling/disabling the receiver or setting RCR=RNCR=0 in the PDC
(Receive (Next) Counter Register).
=> Doing this is beyond the scope of this patch and could add other
bugs, so the original (and working) behaviour should be set for those
platforms (meaning ATMEL_US_USMODE_HWHS flag should be unset).
- For platforms with a FIFO (sama5d2)*, the RTS pin is driven according
to the RX FIFO thresholds, and can be also driven by RTSEN/RTSDIS in
USART Control Register. No problem here.
(This was the use case of commit 1cf6e8fc8341 ("tty/serial: at91: fix
RTS line management when hardware handshake is enabled"))
NB: If the CTS pin declared as a GPIO in the DTS, (for instance
cts-gpios = <&pioA PIN_PB31 GPIO_ACTIVE_LOW>), the transmitter will be
disabled.
=> ATMEL_US_USMODE_HWHS flag can be set for this platform ONLY IF the
CTS pin is not a GPIO.
So, the only case when ATMEL_US_USMODE_HWHS can be enabled is when
(atmel_use_fifo(port) &&
!mctrl_gpio_to_gpiod(atmel_port->gpios, UART_GPIO_CTS))
Tested on all Atmel USART controller flavours:
AT91SAM9G35-CM (DMAC flavour), AT91SAM9G20-EK (PDC flavour),
SAMA5D2xplained (FIFO flavour).
* the list may not be exhaustive
Cc: <stable@vger.kernel.org> #4.4+ (beware, missing atmel_port variable) Fixes: 1cf6e8fc8341 ("tty/serial: at91: fix RTS line management when hardware handshake is enabled") Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Imre Palik [Fri, 21 Oct 2016 08:18:59 +0000 (01:18 -0700)]
perf/x86/intel: Honour the CPUID for number of fixed counters in hypervisors
perf doesn't seem to honour the number of fixed counters specified by CPUID
leaf 0xa. It always assumes that Intel CPUs have at least 3 fixed counters.
So if some of the fixed counters are masked out by the hypervisor, it still
tries to check/set them.
This patch makes perf behave nicer when the kernel is running under a
hypervisor that doesn't expose all the counters.
This patch contains some ideas from Matt Wilson.
Signed-off-by: Imre Palik <imrep@amazon.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Alexander Kozyrev <alexander.kozyrev@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Artyom Kuanbekov <artyom.kuanbekov@intel.com> Cc: David Carrillo-Cisneros <davidcc@google.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Wilson <msw@amazon.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1477037939-15605-1-git-send-email-imrep.amz@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
While it looks like the first WARN() is probably valid, the other one is
triggered by disabling event via perf_event_disable() from atomic context.
The event is disabled here in case we were not able to emulate
the instruction that hit the breakpoint. By disabling the event
we unschedule the event and make sure it's not scheduled back.
But we can't call perf_event_disable() from atomic context, instead
we need to use the event's pending_disable irq_work method to disable it.
Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Huang Ying <ying.huang@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Neuling <mikey@neuling.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20161026094824.GA21397@krava Signed-off-by: Ingo Molnar <mingo@kernel.org>
The reason for the crash is that perf_pmu_unregister() tries to remove
a PMU device which is not added at this point. We add PMU devices
only after pmu_bus is registered, which happens in the
perf_event_sysfs_init() call and sets the 'pmu_bus_running' flag.
The fix is to get the 'pmu_bus_running' flag state at the point
the PMU is taken out of the PMU list and remove the device
later only if it's set.
Reported-by: CAI Qian <caiqian@redhat.com> Tested-by: CAI Qian <caiqian@redhat.com> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rob Herring <robh@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20161020111011.GA13361@krava Signed-off-by: Ingo Molnar <mingo@kernel.org>
Borislav Petkov [Thu, 27 Oct 2016 12:36:23 +0000 (14:36 +0200)]
x86/microcode/AMD: Fix more fallout from CONFIG_RANDOMIZE_MEMORY=y
We needed the physical address of the container in order to compute the
offset within the relocated ramdisk. And we did this by doing __pa() on
the virtual address.
However, __pa() does checks whether the physical address is within
PAGE_OFFSET and __START_KERNEL_map - see __phys_addr() - which fail
if we have CONFIG_RANDOMIZE_MEMORY enabled: we feed a virtual address
which *doesn't* have the randomization offset into a function which uses
PAGE_OFFSET which *does* have that offset.
Linus Torvalds [Fri, 28 Oct 2016 02:58:39 +0000 (19:58 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"20 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/misc/sgi-gru/grumain.c: remove bogus 0x prefix from printk
cris/arch-v32: cryptocop: print a hex number after a 0x prefix
ipack: print a hex number after a 0x prefix
block: DAC960: print a hex number after a 0x prefix
fs: exofs: print a hex number after a 0x prefix
lib/genalloc.c: start search from start of chunk
mm: memcontrol: do not recurse in direct reclaim
CREDITS: update credit information for Martin Kepplinger
proc: fix NULL dereference when reading /proc/<pid>/auxv
mm: kmemleak: ensure that the task stack is not freed during scanning
lib/stackdepot.c: bump stackdepot capacity from 16MB to 128MB
latent_entropy: raise CONFIG_FRAME_WARN by default
kconfig.h: remove config_enabled() macro
ipc: account for kmem usage on mqueue and msg
mm/slab: improve performance of gathering slabinfo stats
mm: page_alloc: use KERN_CONT where appropriate
mm/list_lru.c: avoid error-path NULL pointer deref
h8300: fix syscall restarting
kcov: properly check if we are in an interrupt
mm/slab: fix kmemcg cache creation delayed issue
Daniel Mentz [Fri, 28 Oct 2016 00:46:59 +0000 (17:46 -0700)]
lib/genalloc.c: start search from start of chunk
gen_pool_alloc_algo() iterates over the chunks of a pool trying to find
a contiguous block of memory that satisfies the allocation request.
The shortcut
if (size > atomic_read(&chunk->avail))
continue;
makes the loop skip over chunks that do not have enough bytes left to
fulfill the request. There are two situations, though, where an
allocation might still fail:
(1) The available memory is not contiguous, i.e. the request cannot
be fulfilled due to external fragmentation.
(2) A race condition. Another thread runs the same code concurrently
and is quicker to grab the available memory.
In those situations, the loop calls pool->algo() to search the entire
chunk, and pool->algo() returns some value that is >= end_bit to
indicate that the search failed. This return value is then assigned to
start_bit. The variables start_bit and end_bit describe the range that
should be searched, and this range should be reset for every chunk that
is searched. Today, the code fails to reset start_bit to 0. As a
result, prefixes of subsequent chunks are ignored. Memory allocations
might fail even though there is plenty of room left in these prefixes of
those other chunks.
Fixes: 7f184275aa30 ("lib, Make gen_pool memory allocator lockless") Link: http://lkml.kernel.org/r/1477420604-28918-1-git-send-email-danielmentz@google.com Signed-off-by: Daniel Mentz <danielmentz@google.com> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 28 Oct 2016 00:46:56 +0000 (17:46 -0700)]
mm: memcontrol: do not recurse in direct reclaim
On 4.0, we saw a stack corruption from a page fault entering direct
memory cgroup reclaim, calling into btrfs_releasepage(), which then
tried to allocate an extent and recursed back into a kmem charge ad
nauseam:
On later kernels, kmem charging is opt-in rather than opt-out, and that
particular kmem allocation in btrfs_releasepage() is no longer being
charged and won't recurse and overrun the stack anymore.
But it's not impossible for an accounted allocation to happen from the
memcg direct reclaim context, and we needed to reproduce this crash many
times before we even got a useful stack trace out of it.
Like other direct reclaimers, mark tasks in memcg reclaim PF_MEMALLOC to
avoid recursing into any other form of direct reclaim. Then let
recursive charges from PF_MEMALLOC contexts bypass the cgroup limit.
Link: http://lkml.kernel.org/r/20161025141050.GA13019@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Tejun Heo <tj@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leon Yu [Fri, 28 Oct 2016 00:46:50 +0000 (17:46 -0700)]
proc: fix NULL dereference when reading /proc/<pid>/auxv
Reading auxv of any kernel thread results in NULL pointer dereferencing
in auxv_read() where mm can be NULL. Fix that by checking for NULL mm
and bailing out early. This is also the original behavior changed by
recent commit c5317167854e ("proc: switch auxv to use of __mem_open()").
# cat /proc/2/auxv
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
CPU: 3 PID: 113 Comm: cat Not tainted 4.9.0-rc1-ARCH+ #1
Hardware name: BCM2709
task: ea3b0b00 task.stack: e99b2000
PC is at auxv_read+0x24/0x4c
LR is at do_readv_writev+0x2fc/0x37c
Process cat (pid: 113, stack limit = 0xe99b2210)
Call chain:
auxv_read
do_readv_writev
vfs_readv
default_file_splice_read
splice_direct_to_actor
do_splice_direct
do_sendfile
SyS_sendfile64
ret_fast_syscall
Fixes: c5317167854e ("proc: switch auxv to use of __mem_open()") Link: http://lkml.kernel.org/r/1476966200-14457-1-git-send-email-chianglungyu@gmail.com Signed-off-by: Leon Yu <chianglungyu@gmail.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Kees Cook <keescook@chromium.org> Cc: John Stultz <john.stultz@linaro.org> Cc: Mateusz Guzik <mguzik@redhat.com> Cc: Janis Danisevskis <jdanis@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Catalin Marinas [Fri, 28 Oct 2016 00:46:47 +0000 (17:46 -0700)]
mm: kmemleak: ensure that the task stack is not freed during scanning
Commit 68f24b08ee89 ("sched/core: Free the stack early if
CONFIG_THREAD_INFO_IN_TASK") may cause the task->stack to be freed
during kmemleak_scan() execution, leading to either a NULL pointer fault
(if task->stack is NULL) or kmemleak accessing already freed memory.
This patch uses the new try_get_task_stack() API to ensure that the task
stack is not freed during kmemleak stack scanning.
Dmitry Vyukov [Fri, 28 Oct 2016 00:46:44 +0000 (17:46 -0700)]
lib/stackdepot.c: bump stackdepot capacity from 16MB to 128MB
KASAN uses stackdepot to memorize stacks for all kmalloc/kfree calls.
Current stackdepot capacity is 16MB (1024 top level entries x 4 pages on
second level). Size of each stack is (num_frames + 3) * sizeof(long).
Which gives us ~84K stacks. This capacity was chosen empirically and it
is enough to run kernel normally.
However, when lots of configs are enabled and a fuzzer tries to maximize
code coverage, it easily hits the limit within tens of minutes. I've
tested for long a time with number of top level entries bumped 4x
(4096). And I think I've seen overflow only once. But I don't have all
configs enabled and code coverage has not reached maximum yet. So bump
it 8x to 8192.
Since we have two-level table, memory cost of this is very moderate --
currently the top-level table is 8KB, with this patch it is 64KB, which
is negligible under KASAN.
Here is some approx math.
128MB allows us to memorize ~670K stacks (assuming stack is ~200b).
I've grepped kernel for kmalloc|kfree|kmem_cache_alloc|kmem_cache_free|
kzalloc|kstrdup|kstrndup|kmemdup and it gives ~60K matches. Most of
alloc/free call sites are reachable with only one stack. But some
utility functions can have large fanout. Assuming average fanout is 5x,
total number of alloc/free stacks is ~300K.
Link: http://lkml.kernel.org/r/1476458416-122131-1-git-send-email-dvyukov@google.com Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Baozeng Ding <sploving1@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kees Cook [Fri, 28 Oct 2016 00:46:41 +0000 (17:46 -0700)]
latent_entropy: raise CONFIG_FRAME_WARN by default
When building with the latent_entropy plugin, set the default
CONFIG_FRAME_WARN to 2048, since some __init functions have many basic
blocks that, when instrumented by the latent_entropy plugin, grow beyond
1024 byte stack size on 32-bit builds.
Link: http://lkml.kernel.org/r/20161018211216.GA39687@beast Signed-off-by: Kees Cook <keescook@chromium.org> Reported-by: kbuild test robot <fengguang.wu@intel.com> Cc: Emese Revfy <re.emese@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Michal Marek <mmarek@suse.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Tejun Heo <tj@kernel.org> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Masahiro Yamada [Fri, 28 Oct 2016 00:46:38 +0000 (17:46 -0700)]
kconfig.h: remove config_enabled() macro
The use of config_enabled() is ambiguous. For config options,
IS_ENABLED(), IS_REACHABLE(), etc. will make intention clearer.
Sometimes config_enabled() has been used for non-config options because
it is useful to check whether the given symbol is defined or not.
I have been tackling on deprecating config_enabled(), and now is the
time to finish this work.
Some new users have appeared for v4.9-rc1, but it is trivial to replace
them:
- arch/x86/mm/kaslr.c
replace config_enabled() with IS_ENABLED() because
CONFIG_X86_ESPFIX64 and CONFIG_EFI are boolean.
- include/asm-generic/export.h
replace config_enabled() with __is_defined().
Then, config_enabled() can be removed now.
Going forward, please use IS_ENABLED(), IS_REACHABLE(), etc. for config
options, and __is_defined() for non-config symbols.
Link: http://lkml.kernel.org/r/1476616078-32252-1-git-send-email-yamada.masahiro@socionext.com Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Kees Cook <keescook@chromium.org> Cc: Michal Marek <mmarek@suse.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Thomas Garnier <thgarnie@google.com> Cc: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aristeu Rozanski [Fri, 28 Oct 2016 00:46:35 +0000 (17:46 -0700)]
ipc: account for kmem usage on mqueue and msg
When kmem accounting switched from account by default to only account if
flagged by __GFP_ACCOUNT, IPC mqueue and messages was left out.
The production use case at hand is that mqueues should be customizable
via sysctls in Docker containers in a Kubernetes cluster. This can only
be safely allowed to the users of the cluster (without the risk that
they can cause resource shortage on a node, influencing other users'
containers) if all resources they control are bounded, i.e. accounted
for.
Link: http://lkml.kernel.org/r/1476806075-1210-1-git-send-email-arozansk@redhat.com Signed-off-by: Aristeu Rozanski <arozansk@redhat.com> Reported-by: Stefan Schimanski <sttts@redhat.com> Acked-by: Davidlohr Bueso <dave@stgolabs.net> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Stefan Schimanski <sttts@redhat.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm/slab: improve performance of gathering slabinfo stats
On large systems, when some slab caches grow to millions of objects (and
many gigabytes), running 'cat /proc/slabinfo' can take up to 1-2
seconds. During this time, interrupts are disabled while walking the
slab lists (slabs_full, slabs_partial, and slabs_free) for each node,
and this sometimes causes timeouts in other drivers (for instance,
Infiniband).
This patch optimizes 'cat /proc/slabinfo' by maintaining a counter for
total number of allocated slabs per node, per cache. This counter is
updated when a slab is created or destroyed. This enables us to skip
traversing the slabs_full list while gathering slabinfo statistics, and
since slabs_full tends to be the biggest list when the cache is large,
it results in a dramatic performance improvement. Getting slabinfo
statistics now only requires walking the slabs_free and slabs_partial
lists, and those lists are usually much smaller than slabs_full.
We tested this after growing the dentry cache to 70GB, and the
performance improved from 2s to 5ms.
Link: http://lkml.kernel.org/r/1472517876-26814-1-git-send-email-aruna.ramakrishna@oracle.com Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com> Acked-by: David Rientjes <rientjes@google.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As described in https://bugzilla.kernel.org/show_bug.cgi?id=177821:
After some analysis it seems to be that the problem is in alloc_super().
In case list_lru_init_memcg() fails it goes into destroy_super(), which
calls list_lru_destroy().
And in list_lru_init() we see that in case memcg_init_list_lru() fails,
lru->node is freed, but not set NULL, which then leads list_lru_destroy()
to believe it is initialized and call memcg_destroy_list_lru().
memcg_destroy_list_lru() in turn can access lru->node[i].memcg_lrus,
which is NULL.
[akpm@linux-foundation.org: add comment] Signed-off-by: Alexander Polakov <apolyakov@beget.ru> Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Rutland [Fri, 28 Oct 2016 00:46:24 +0000 (17:46 -0700)]
h8300: fix syscall restarting
Back in commit f56141e3e2d9 ("all arches, signal: move restart_block to
struct task_struct"), all architectures and core code were changed to
use task_struct::restart_block. However, when h8300 support was
subsequently restored in v4.2, it was not updated to account for this,
and maintains thread_info::restart_block, which is not kept in sync.
This patch drops the redundant restart_block from thread_info, and moves
h8300 to the common one in task_struct, ensuring that syscall restarting
always works as expected.
Fixes: f56141e3e2d9 ("all arches, signal: move restart_block to struct task_struct") Link: http://lkml.kernel.org/r/1476714934-11635-1-git-send-email-mark.rutland@arm.com Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: uclinux-h8-devel@lists.sourceforge.jp Cc: <stable@vger.kernel.org> [4.2+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrey Konovalov [Fri, 28 Oct 2016 00:46:21 +0000 (17:46 -0700)]
kcov: properly check if we are in an interrupt
in_interrupt() returns a nonzero value when we are either in an
interrupt or have bh disabled via local_bh_disable(). Since we are
interested in only ignoring coverage from actual interrupts, do a proper
check instead of just calling in_interrupt().
As a result of this change, kcov will start to collect coverage from
within local_bh_disable()/local_bh_enable() sections.
This issue is caused by kmemcg feature that try to create new set of
kmem_caches for each memcg. Recently, kmem_cache creation is slowed by
synchronize_sched() and futher kmem_cache creation is also delayed since
kmem_cache creation is synchronized by a global slab_mutex lock. So,
the number of kworker that try to create kmem_cache increases quietly.
synchronize_sched() is for lockless access to node's shared array but
it's not needed when a new kmem_cache is created. So, this patch rules
out that case.
Fixes: 801faf0db894 ("mm/slab: lockless decision to grow cache") Link: http://lkml.kernel.org/r/1475734855-4837-1-git-send-email-iamjoonsoo.kim@lge.com Reported-by: Doug Smythies <dsmythies@telus.net> Tested-by: Doug Smythies <dsmythies@telus.net> Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Williams [Fri, 28 Oct 2016 00:04:05 +0000 (17:04 -0700)]
device-dax: fix percpu_ref_exit ordering
We need to wait until the percpu_ref is released before exit. Otherwise,
we sometimes lose the race and trigger this new warning that was added
in v4.9 (commit a67823c1ed10 "percpu-refcount: init ->confirm_switch
member properly"):
Cc: <stable@vger.kernel.org> Fixes: ab68f2622136 ("/dev/dax, pmem: direct access to persistent memory") Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Thu, 27 Oct 2016 23:23:01 +0000 (16:23 -0700)]
Allow KASAN and HOTPLUG_MEMORY to co-exist when doing build testing
No, KASAN may not be able to co-exist with HOTPLUG_MEMORY at runtime,
but for build testing there is no reason not to allow them together.
This hopefully means better build coverage and fewer embarrasing silly
problems like the one fixed by commit 9db4f36e82c2 ("mm: remove unused
variable in memory hotplug") in the future.
Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Tue, 25 Oct 2016 15:52:04 +0000 (17:52 +0200)]
nvdimm: make CONFIG_NVDIMM_DAX 'bool'
A bugfix just tried to address a randconfig build problem and introduced
a variant of the same problem: with CONFIG_LIBNVDIMM=y and
CONFIG_NVDIMM_DAX=m, the nvdimm module now fails to link:
drivers/nvdimm/built-in.o: In function `to_nd_device_type':
bus.c:(.text+0x1b5d): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nd_region_notify_driver_action.constprop.2':
region_devs.c:(.text+0x6b6c): undefined reference to `is_nd_dax'
region_devs.c:(.text+0x6b8c): undefined reference to `to_nd_dax'
drivers/nvdimm/built-in.o: In function `nd_region_probe':
region.c:(.text+0x70f3): undefined reference to `nd_dax_create'
drivers/nvdimm/built-in.o: In function `mode_show':
namespace_devs.c:(.text+0xa196): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nvdimm_namespace_common_probe':
(.text+0xa55f): undefined reference to `is_nd_dax'
drivers/nvdimm/built-in.o: In function `nvdimm_namespace_common_probe':
(.text+0xa56e): undefined reference to `to_nd_dax'
This reverts the earlier fix, making NVDIMM_DAX a 'bool' option again
as it should be (it gets linked into the libnvdimm module). To fix
the original problem, I'm adding a dependency on LIBNVDIMM to
DEV_DAX_PMEM, which ensures we can't have that one built-in if the
rest is a module.
Fixes: 4e65e9381c7a ("/dev/dax: fix Kconfig dependency build breakage") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Thu, 27 Oct 2016 22:49:12 +0000 (15:49 -0700)]
mm: remove unused variable in memory hotplug
When I removed the per-zone bitlock hashed waitqueues in commit 9dcb8b685fc3 ("mm: remove per-zone hashtable of bitlock waitqueues"), I
removed all the magic hotplug memory initialization of said waitqueues
too.
But when I actually _tested_ the resulting build, I stupidly assumed
that "allmodconfig" would enable memory hotplug. And it doesn't,
because it enables KASAN instead, which then disables hotplug memory
support.
As a result, my build test of the per-zone waitqueues was totally
broken, and I didn't notice that the compiler warns about the now unused
iterator variable 'i'.
I guess I should be happy that that seems to be the worst breakage from
my clearly horribly failed test coverage.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 27 Oct 2016 22:06:29 +0000 (15:06 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has some driver bugfixes, module autoload fixes, and driver
enablement on some architectures"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: defer probe if bus recovery GPIOs are not ready
i2c: designware: Avoid aborted transfers with fast reacting I2C slaves
i2c: i801: Fix I2C Block Read on 8-Series/C220 and later
i2c: xgene: Avoid dma_buffer overrun
i2c: digicolor: Fix module autoload
i2c: xlr: Fix module autoload for OF registration
i2c: xlp9xx: Fix module autoload
i2c: jz4780: Fix module autoload
i2c: allow configuration of imx driver for ColdFire architecture
i2c: mark device nodes only in case of successful instantiation
i2c: rk3x: Give the tuning value 0 during rk3x_i2c_v0_calc_timings
i2c: hix5hd2: allow build with ARCH_HISI
Linus Torvalds [Thu, 27 Oct 2016 21:33:08 +0000 (14:33 -0700)]
Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
"The latest Thermal Management updates for v4.9-rc3:
- Fix a regression introduced by commit b721ca0d19(thermal/powerclamp: remove cpu whitelist), that
powerclamp driver checks cpu support in a wrong way. From: Eric
Ernst.
- Fix a problem that intel_pch_thermal driver misses passive trip
point when the PCH thermal device has an ACPI companion device
associated. From: Srinivas Pandruvada.
- Add missing support for Haswell PCH thermal sensor. From: Srinivas
Pandruvada"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/powerclamp: correct cpu support check
thermal: intel_pch_thermal: Enable Haswell PCH
thermal: intel_pch_thermal: Add an ACPI passive trip
Linus Torvalds [Thu, 27 Oct 2016 21:16:30 +0000 (14:16 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A few more s390 patches for 4.9:
- a fix for an overflow in the dasd driver reported by UBSAN
- fix a regression and add hotplug memory to the zone movable again
- add ignore defines for the pkey system calls
- fix the ouput of the merged stack tracer
- replace printk with pr_cont in arch/s390 where appropriate
- remove the arch specific return_address function again
- ignore reserved channel paths at boot time
- add a missing hugetlb_bad_size call to the arch backend"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: fix zone calculation in arch_add_memory()
s390/dumpstack: use pr_cont within show_stack and die
s390/dumpstack: get rid of return_address again
s390/disassambler: use pr_cont where appropriate
s390/dumpstack: use pr_cont where appropriate
s390/dumpstack: restore reliable indicator for call traces
s390/mm: use hugetlb_bad_size()
s390/cio: don't register chpids in reserved state
s390: ignore pkey system calls
s390/dasd: avoid undefined behaviour
Linus Torvalds [Thu, 27 Oct 2016 21:12:04 +0000 (14:12 -0700)]
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module maintainership updates from Rusty Russell:
"(Quoting from the MAINTAINERS commit:)
Being a Linux kernel maintainer has been my proudest professional
accomplishment, spanning the last 19 years. But now we have a surfeit
of excellent hackers, and I can hand this over without regret.
I'll still be around as co-maintainer for another cycle, but Jessica
is now the one to convince if you want your patches applied. She
rocks, and is far more timely than me too!"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MAINTAINERS: Begin module maintainer transition
Linus Torvalds [Thu, 27 Oct 2016 19:52:46 +0000 (12:52 -0700)]
Merge tag 'for-linus-4.9-rc2-ofs-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull oreangefs updates from Mike Marshall:
"A couple of orangefs cleanups sent in by other developers:
- use d_fsdata instead of d_time (Miklos Szeredi)
- use file_inode(file) instead of file->f_path.dentry->d_inode (Amir
Goldstein)"
* tag 'for-linus-4.9-rc2-ofs-1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: don't use d_time
orangefs: user file_inode() where it is due
Linus Torvalds [Thu, 27 Oct 2016 19:34:50 +0000 (12:34 -0700)]
Merge tag 'xfs-fixes-for-linus-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This update contains fixes for most of the outstanding regressions
introduced with the 4.9-rc1 XFS merge. There is also a fix for an
iomap bug, too.
This is a quite a bit larger than I'd prefer for a -rc3, but most of
the change comes from cleaning up the new reflink copy on write code;
it's much simpler and easier to understand now. These changes fixed
several bugs in the new code, and it wasn't clear that there was an
easier/simpler way to fix them. The rest of the fixes are the usual
size you'd expect at this stage.
I've left the commits to soak in linux-next for a some extra time
because of the size before asking you to pull, no new problems with
them have been reported so I think it's all OK.
Summary:
- iomap page offset masking fix for page faults
- add IOMAP_REPORT to distinguish between read and fiemap map
requests
- cleanups to new shared data extent code
- fix mount active status on failed log recovery
- fix broken dquots in a buffer calculation
- fix locking order issues and merge xfs_reflink_remap_range and
xfs_file_share_range
- rework unmapping of CoW extents and remove now unused functions
- clean state when CoW is done"
* tag 'xfs-fixes-for-linus-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (25 commits)
xfs: clear cowblocks tag when cow fork is emptied
xfs: fix up inode cowblocks tracking tracepoints
fs: Do to trim high file position bits in iomap_page_mkwrite_actor
xfs: remove xfs_bunmapi_cow
xfs: optimize xfs_reflink_end_cow
xfs: optimize xfs_reflink_cancel_cow_blocks
xfs: refactor xfs_bunmapi_cow
xfs: optimize writes to reflink files
xfs: don't bother looking at the refcount tree for reads
xfs: handle "raw" delayed extents xfs_reflink_trim_around_shared
xfs: add xfs_trim_extent
iomap: add IOMAP_REPORT
xfs: merge xfs_reflink_remap_range and xfs_file_share_range
xfs: remove xfs_file_wait_for_io
xfs: move inode locking from xfs_reflink_remap_range to xfs_file_share_range
xfs: fix the same_inode check in xfs_file_share_range
xfs: remove the same fs check from xfs_file_share_range
libxfs: v3 inodes are only valid on crc-enabled filesystems
libxfs: clean up _calc_dquots_per_chunk
xfs: unset MS_ACTIVE if mount fails
...
Chris Mason [Thu, 27 Oct 2016 17:42:20 +0000 (10:42 -0700)]
btrfs: fix races on root_log_ctx lists
btrfs_remove_all_log_ctxs takes a shortcut where it avoids walking the
list because it knows all of the waiters are patiently waiting for the
commit to finish.
But, there's a small race where btrfs_sync_log can remove itself from
the list if it finds a log commit is already done. Also, it uses
list_del_init() to remove itself from the list, but there's no way to
know if btrfs_remove_all_log_ctxs has already run, so we don't know for
sure if it is safe to call list_del_init().
This gets rid of all the shortcuts for btrfs_remove_all_log_ctxs(), and
just calls it with the proper locking.
This is part two of the corruption fixed by cbd60aa7cd1. I should have
done this in the first place, but convinced myself the optimizations were
safe. A 12 hour run of dbench 2048 will eventually trigger a list debug
WARN_ON for the list_del_init() in btrfs_sync_log().
Fixes: d1433debe7f4346cf9fc0dafc71c3137d2a97bc4 Reported-by: Dave Jones <davej@codemonkey.org.uk>
cc: stable@vger.kernel.org # 3.15+ Signed-off-by: Chris Mason <clm@fb.com>
Linus Torvalds [Thu, 27 Oct 2016 17:08:58 +0000 (10:08 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one is a fatal section mismatch (reference to init
after it's discarded) and the other two are iscsi locking fixes"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: NCR5380: no longer mark irq probing as __init
scsi: be2iscsi: Replace _bh with _irqsave/irqrestore
scsi: libiscsi: Fix locking in __iscsi_conn_send_pdu
Linus Torvalds [Thu, 27 Oct 2016 17:07:13 +0000 (10:07 -0700)]
Merge branch 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"The AHCI MSI handling change in rc1 was a bit broken and caused disk
probing failures on some machines. These three patches should fix the
issues"
David Howells comments:
"My test machine fell foul of this using a PCIe M.2-attached SSD card.
The patches fix it for me"
* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix the single MSI-X case in ahci_init_one
ahci: fix nvec check
ahci: only try to use multi-MSI mode if there is more than 1 port
Linus Torvalds [Thu, 27 Oct 2016 17:05:31 +0000 (10:05 -0700)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of fixes for this series, most notably the fix for the blk-mq
software queue regression in from this merge window.
Apart from that, a fix for an unlikely hang if a queue is flooded with
FUA requests from Ming, and a few small fixes for nbd and badblocks.
Lastly, a rename update for the proc softirq output, since the block
polling code was made generic"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: update hardware and software queues for sleeping alloc
block: flush: fix IO hang in case of flood fua req
nbd: fix incorrect unlock of nbd->sock_lock in sock_shutdown
badblocks: badblocks_set/clear update unacked_exist
softirq: Display IRQ_POLL for irq-poll statistics
Linus Torvalds [Wed, 26 Oct 2016 17:15:30 +0000 (10:15 -0700)]
mm: remove per-zone hashtable of bitlock waitqueues
The per-zone waitqueues exist because of a scalability issue with the
page waitqueues on some NUMA machines, but it turns out that they hurt
normal loads, and now with the vmalloced stacks they also end up
breaking gfs2 that uses a bit_wait on a stack object:
where 'gh' can be a reference to the local variable 'mount_gh' on the
stack of fill_super().
The reason the per-zone hash table breaks for this case is that there is
no "zone" for virtual allocations, and trying to look up the physical
page to get at it will fail (with a BUG_ON()).
It turns out that I actually complained to the mm people about the
per-zone hash table for another reason just a month ago: the zone lookup
also hurts the regular use of "unlock_page()" a lot, because the zone
lookup ends up forcing several unnecessary cache misses and generates
horrible code.
As part of that earlier discussion, we had a much better solution for
the NUMA scalability issue - by just making the page lock have a
separate contention bit, the waitqueue doesn't even have to be looked at
for the normal case.
Peter Zijlstra already has a patch for that, but let's see if anybody
even notices. In the meantime, let's fix the actual gfs2 breakage by
simplifying the bitlock waitqueues and removing the per-zone issue.
Reported-by: Andreas Gruenbacher <agruenba@redhat.com> Tested-by: Bob Peterson <rpeterso@redhat.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Steven Whitehouse <swhiteho@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>