media: imx-csi: Double crop height for alternate fields at sink
If the incoming sink field type is alternate, the reset crop height
and crop height bounds must be set to twice the incoming height,
because in alternate field mode, upstream will report only the
lines for a single field, and the CSI captures the whole frame.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
IDMAC interlaced scan, a.k.a. interweave, should be enabled in the
IDMAC output channels only if the IDMAC output pad field type is
'seq-bt' or 'seq-tb', and field type at the capture interface is
'interlaced*'.
V4L2_FIELD_HAS_BOTH() macro should not be used on the input to determine
enabling interlaced/interweave scan. That macro includes the 'interlaced'
field types, and in those cases the data is already interweaved with
top/bottom field lines.
The CSI will capture whole frames when the source specifies alternate
field mode. So the CSI also enables interweave for alternate input
field type and the field type at capture interface is interlaced.
Fix the logic for setting field type in try_fmt in CSI entity.
The behavior should be:
- No restrictions on field type at sink pad.
- At the output pads, allow sequential fields in TB order, if the sink pad
field type is sequential or alternate. Otherwise passthrough the field
type from sink to source pad.
Move this logic to new function csi_try_field().
These changes result in the following allowed field transformations
from CSI sink -> source pads (all other field types at sink are passed
through to source):
This will require supporting interweave with top/bottom line swapping.
Until then seq-bt is not allowed at the CSI source pad because there is
no way to swap top/bottom lines when interweaving to INTERLACED_BT --
note that despite the name, INTERLACED_BT is top-bottom order in memory.
The BT in this case refers to field dominance: the bottom lines are
older in time than the top lines.
The capture interface device allows selecting IDMAC interweave by
choosing INTERLACED_TB if the CSI/PRPENCVF source pad is seq-tb and
INTERLACED_BT if the source pad is seq-bt (for future support of seq-bt).
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: gpu: ipu-v3: Add planar support to interlaced scan
To support interlaced scan with planar formats, cpmem SLUV must
be programmed with the correct chroma line stride. For full and
partial planar 4:2:2 (YUV422P, NV16), chroma line stride must
be doubled. For full and partial planar 4:2:0 (YUV420, YVU420, NV12),
chroma line stride must _not_ be doubled, since a single chroma line
is shared by two luma lines.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: gpu: ipu-csi: Swap fields according to input/output field types
The function ipu_csi_init_interface() was inverting the F-bit for
NTSC case, in the CCIR_CODE_1/2 registers. The result being that
for NTSC bottom-top field order, the CSI would swap fields and
capture in top-bottom order.
Instead, base field swap on the field order of the input to the CSI,
and the field order of the requested output. If the input/output
fields are sequential but different, swap fields, otherwise do
not swap. This requires passing both the input and output mbus
frame formats to ipu_csi_init_interface().
Move this code to a new private function ipu_csi_set_bt_interlaced_codes()
that programs the CCIR_CODE_1/2 registers for interlaced BT.656 (and
possibly interlaced BT.1120 in the future).
When detecting input video standard from the input frame width/height,
make sure to double height if input field type is alternate, since
in that case input height only includes lines for one field.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
V4L2_FIELD_IS_SEQUENTIAL: returns true if the given field type is
'sequential', that is a full frame is transmitted, or exists in
memory, as all top field lines followed by all bottom field lines,
or vice-versa.
V4L2_FIELD_IS_INTERLACED: returns true if the given field type is
'interlaced', that is a full frame is transmitted, or exists in
memory, as top field lines interlaced with bottom field lines.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Steve Longerbeam [Tue, 15 Jan 2019 01:10:19 +0000 (20:10 -0500)]
media: rcar-vin: Allow independent VIN link enablement
There is a block of code in rvin_group_link_notify() that prevents
enabling a link to a VIN node if any entity in the media graph is
in use. This prevents enabling a VIN link even if there is an in-use
entity somewhere in the graph that is independent of the link's
pipeline.
For example, the code block will prevent enabling a link from
the first rcar-csi2 receiver to a VIN node even if there is an
enabled link somewhere far upstream on the second independent
rcar-csi2 receiver pipeline.
If this code block is meant to prevent modifying a link if any entity
in the graph is actively involved in streaming (because modifying
the CHSEL register fields can disrupt any/all running streams), then
the entities stream counts should be checked rather than the use counts.
(There is already such a check in __media_entity_setup_link() that verifies
the stream_count of the link's source and sink entities are both zero,
but that is insufficient, since there should be no running streams in
the entire graph).
Modify the code block to check the entity stream_count instead of the
use_count (and elaborate on the comment). VIN node links can now be
enabled even if there are other independent in-use entities that are
not streaming.
Fixes: c0cc5aef31 ("media: rcar-vin: add link notify for Gen3") Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Thu, 10 Jan 2019 16:56:10 +0000 (11:56 -0500)]
media: v4l2-ctrl: Add control for h.264 chroma qp offset
Allow to add fixed quantization parameter offset between luma and
chroma quantization parameters. This control directly corresponds
to the chroma_qp_index_offset field of the h.264 picture parameter
set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Thu, 10 Jan 2019 16:56:09 +0000 (11:56 -0500)]
media: v4l2-ctrl: Add control to enable h.264 constrained intra prediction
Allow to enable h.264 constrained intra prediction (macroblocks using
intra prediction modes are not allowed to use residual data and decoded
samples of neighboring macroblocks coded using inter prediction modes).
This control directly corresponds to the constrained_intra_pred_flag
field in the h.264 picture parameter set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The COM3 register at address 0x0c already defaults to 0x10, the two bits
COM3[7:6] are set according to V4L2 controls by sethvflip later.
There is no need to set it multiple times during bridge initialization.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 14 Dec 2018 16:40:29 +0000 (11:40 -0500)]
media: gspca: ov534-ov722x: remove mode specific video data registers from bridge_init
The video format, payload size, and frame size setup is video format
and frame size specific. Those registers are overwritten during
bridge_start anyway.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 14 Dec 2018 16:40:27 +0000 (11:40 -0500)]
media: gspca: ov543-ov772x: move video format specific registers into bridge_start
In preparation for adding SGBRG8 as a second video format besides YUYV,
move video format specific register settings from the bridge_init array
into the bridge_start arrays.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 14 Dec 2018 16:40:26 +0000 (11:40 -0500)]
media: gspca: support multiple pixel formats in TRY_FMT
If a driver supports multiple pixel formats with the same frame size,
TRY_FMT will currently always return the first pixel format.
Fix this by adding pixelformat support to wxh_to_nearest_mode().
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 14 Dec 2018 16:40:25 +0000 (11:40 -0500)]
media: gspca: support multiple pixel formats in ENUM_FRAMEINTERVALS
If a driver supports multiple pixel formats with the same frame size,
ENUM_FRAMEINTERVALS will currently only work for the first pixel format.
Fix this by adding pixelformat support to wxh_to_mode().
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Fri, 11 Jan 2019 11:37:03 +0000 (06:37 -0500)]
media: vivid: do not implement VIDIOC_S_PARM for output streams
v4l2_compliance gave a warning for the S_PARM test for output streams:
warn: v4l2-test-formats.cpp(1235): S_PARM is supported for buftype 2, but not for ENUM_FRAMEINTERVALS
The reason is that vivid mapped s_parm for output streams to g_parm. But if
S_PARM doesn't actually change anything, then it shouldn't be enabled at all.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Mon, 14 Jan 2019 16:23:52 +0000 (11:23 -0500)]
media: vivid: take data_offset into account for video output
The video output sizeimage calculation did not take data_offset into account.
This can cause problems with video loopback or exporting output buffers for
use as dmabuf import buffers since the output buffer size is now too small.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Mon, 14 Jan 2019 14:01:54 +0000 (09:01 -0500)]
media: v4l: uAPI: V4L2_BUF_TYPE_META_OUTPUT is an output buffer type
V4L2_BUF_TYPE_META_OUTPUT was added by commit 72148d1a57e7
("media: v4l: Add support for V4L2_BUF_TYPE_META_OUTPUT") but the patch
missed adding the type to the macro telling whether a given type is an
output type or not. Do that now. Getting this wrong leads to handling the
buffer as a capture buffer in a lot of places.
Fixes: 72148d1a57e7 ("media: v4l: Add support for V4L2_BUF_TYPE_META_OUTPUT") Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Chen-Yu Tsai [Fri, 30 Nov 2018 07:58:45 +0000 (02:58 -0500)]
media: sun6i: Add H3 compatible
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Add a compatible string entry for the H3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Chen-Yu Tsai [Fri, 30 Nov 2018 07:58:44 +0000 (02:58 -0500)]
media: dt-bindings: media: sun6i: Separate H3 compatible from A31
The CSI controller found on the H3 (and H5) is a reduced version of the
one found on the A31. It only has 1 channel, instead of 4 channels for
time-multiplexed BT.656. Since the H3 is a reduced version, it cannot
"fallback" to a compatible that implements more features than it
supports.
Split out the H3 compatible as a separate entry, with no fallback.
Fixes: b7eadaa3a02a ("media: dt-bindings: media: sun6i: Add A31 and H3 compatibles") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Petr Cvek [Thu, 13 Dec 2018 15:39:19 +0000 (10:39 -0500)]
media: i2c: ov9640: fix missing error handling in probe
Control handlers registration lacked error path with
v4l2_ctrl_handler_free() call. Fix it by using goto to alread existing
v4l2_ctrl_handler_free() call.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Petr Cvek [Thu, 13 Dec 2018 15:39:13 +0000 (10:39 -0500)]
media: i2c: ov9640: drop soc_camera code and switch to v4l2_async
This patch removes the dependency on an obsoleted soc_camera from ov9640
driver and changes the code to be a standalone v4l2 async subdevice.
It also adds GPIO allocations for power and reset signals (as they are not
handled by soc_camera now).
The values for waiting on GPIOs (reset and power) settling down were taken
from the datasheet (> 1 ms after HW/SW reset). The upper limit was chosen
as an arbitrary value. Also one occurrence of mdelay() was changed to
msleep(). The delays were successfully tested on a real hardware.
The patch makes ov9640 sensor again compatible with the pxa_camera driver.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Petr Cvek [Thu, 13 Dec 2018 15:39:12 +0000 (10:39 -0500)]
media: soc_camera: ov9640: move ov9640 out of soc_camera
Initial part of ov9640 transition from soc_camera subsystem to a standalone
v4l2 subdevice. The soc_camera version seems to be used only in Palm Zire72
and in (the future) HTC Magician. On these two devices the support is
broken as pxa_camera driver doesn't use soc_camera anymore. The other
mentions from git grep are "TODOs" (in board-osk.c) or chip names for
unsupported sensors on HW which doesn't use soc_camera at all (irelevant).
Copy the driver files from soc_camera and mark the original ones in the
Kconfig description as obsoleted.
Add config option VIDEO_OV9640 to the build files in drivers/media/i2c.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The following commits:
commit f6dd927f34d6 ("[media] media: ov7670: calculate framerate properly for ov7675")
commit 04ee6d92047e ("[media] media: ov7670: add possibility to bypass pll for ov7675")
introduced the ability to bypass PLL multiplier and use input clock (xvclk)
as pixel clock output frequency for ov7675 sensor.
PLL is bypassed using register DBLV[7:6], according to ov7670 and ov7675
sensor manuals. Macros used to set DBLV register seem wrong in the
driver, as their values do not match what reported in the datasheet.
Fix by changing DBLV_* macros to use bits [7:6] and set bits [3:0] to
default 0x0a reserved value (according to datasheets).
While at there, remove a write to DBLV register in
"ov7675_set_framerate()" that over-writes the previous one to the same
register that takes "info->pll_bypass" flag into account instead of setting PLL
multiplier to 4x unconditionally.
And, while at there, since "info->pll_bypass" is only used in
set/get_framerate() functions used by ov7675 only, it is not necessary
to check for the device id at probe time to make sure that when using
ov7670 "info->pll_bypass" is set to false.
media: dt-bindings: media: i2c: Fix external clock frequency for OV5645
Commit "4adb0a0432f4 media: ov5645: Supported external clock is 24MHz"
modified the external clock frequency to be 24MHz instead of the
23.88MHz in driver. Hence, modify the frequency value in binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus [Fri, 30 Nov 2018 22:30:48 +0000 (17:30 -0500)]
media: ipu3-cio2: Allow probe to succeed if there are no sensors connected
The device won't be powered off on systems that have no sensors connected
unless it has a driver bound to it. Allow that to happen even if there are
no sensors connected to cio2.
Pawe? Chmiel [Wed, 9 Jan 2019 18:00:41 +0000 (13:00 -0500)]
media: s5p-jpeg: Correct step and max values for V4L2_CID_JPEG_RESTART_INTERVAL
This commit corrects max and step values for v4l2 control for
V4L2_CID_JPEG_RESTART_INTERVAL. Max should be 0xffff and step should be 1.
It was found by using v4l2-compliance tool and checking result of
VIDIOC_QUERY_EXT_CTRL/QUERYMENU test.
Previously it was complaining that step was bigger than difference
between max and min.
Niklas Söderlund [Thu, 29 Nov 2018 02:01:47 +0000 (21:01 -0500)]
media: i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter
The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
operate using 1-, 2- and 4-lanes. Update the driver to support all
available modes.
The driver makes use of large tables of static register/value writes
when powering up/down the TXA and TXB transmitters which include the
write to the NUM_LANES register. By converting the tables into functions
and using parameters the power up/down functions for TXA and TXB power
up/down can be merged and used for both transmitters.
Niklas Söderlund [Thu, 29 Nov 2018 02:01:46 +0000 (21:01 -0500)]
media: i2c: adv748x: store number of CSI-2 lanes described in device tree
The adv748x CSI-2 transmitters TXA and TXB can use different number of
lanes to transmit data. In order to be able to configure the device
correctly this information need to be parsed from device tree and stored
in each TX private data structure.
TXA supports 1, 2 and 4 lanes while TXB supports 1 lane.
Niklas Söderlund [Thu, 29 Nov 2018 02:01:45 +0000 (21:01 -0500)]
media: i2c: adv748x: reuse power up sequence when initializing CSI-2
Extend the MIPI CSI-2 power up sequence to match the power up sequence
in the hardware manual chapter "9.5.1 Power Up Sequence". This change
allows the power up functions to be reused when initializing the
hardware reducing code duplicating as well aligning with the
documentation.
Niklas Söderlund [Thu, 29 Nov 2018 02:01:44 +0000 (21:01 -0500)]
media: dt-bindings: adv748x: make data-lanes property mandatory for CSI-2 endpoints
The CSI-2 transmitters can use a different number of lanes to transmit
data. Make the data-lanes mandatory for the endpoints that describe the
transmitters as no good default can be set to fallback on.
Aditya Pakki [Thu, 27 Dec 2018 18:58:01 +0000 (13:58 -0500)]
media: dvb: Add check on sp8870_readreg
In sp8870_set_frontend_parameters, the function sp8870_readreg
may return an error when i2c_transfer fails. The fix checks for
this error and returns upstream consistent with other invocations.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ettore Chimenti [Thu, 27 Dec 2018 13:06:35 +0000 (08:06 -0500)]
media: secocec: fix ir address shift
The actual value of the RC5 System Number (address) is stored in the
IR_READ_DATA common register masked with 0x1F00 so it have to be shifted
by 8 bits.
Signed-off-by: Ettore Chimenti <ek5.chimenti@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kangjie Lu [Fri, 21 Dec 2018 07:07:20 +0000 (02:07 -0500)]
media: mt312: fix a missing check of mt312 reset
mt312_reset() may fail. Although it is called in the end of
mt312_set_frontend(), we better check its status and return its error
code upstream instead of 0.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Kangjie Lu [Thu, 20 Dec 2018 07:48:42 +0000 (02:48 -0500)]
media: lgdt3306a: fix a missing check of return value
If lgdt3306a_read_reg() fails, the read data in "val" is incorrect, thus
shouldn't be further used. The fix inserts a check for the return value
of lgdt3306a_read_reg(). If it fails, goto fail.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Arnd Bergmann [Mon, 10 Dec 2018 20:41:40 +0000 (15:41 -0500)]
media: seco-cec: fix RC_CORE dependency
All other drivers that need RC_CORE have a dependency rather than using
'select', so we should do the same here to avoid circular dependencies
as well as this warning about missing dependencies:
WARNING: unmet direct dependencies detected for RC_CORE
Depends on [n]: INPUT [=n]
Selected by [y]:
- VIDEO_SECO_RC [=y] && MEDIA_SUPPORT [=y] && CEC_PLATFORM_DRIVERS [=y] && VIDEO_SECO_CEC [=y]
Fixes: daef95769b3a ("media: seco-cec: add Consumer-IR support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: rcar-vin: remove unneeded locking in async callbacks
The locking implemented in the async notifier callbacks are unnecessary
as the global list_lock in v4l2-async.c is held whenever one of the
callbacks are called.
The locking in itself is not harmful however it produces a LOCKDEP
warning between the global v4l2-async list_lock and the rcar-vin local
locking schema. Remove the rcar-vin locking for the async callbacks to
reduce complexity and silent the false LOCKDEP warning.
Pawe? Chmiel [Sat, 29 Dec 2018 15:46:01 +0000 (10:46 -0500)]
media: s5p-jpeg: Check for fmt_ver_flag when doing fmt enumeration
Previously when doing format enumeration, it was returning all
formats supported by driver, even if they're not supported by hw.
Add missing check for fmt_ver_flag, so it'll be fixed and only those
supported by hw will be returned. Similar thing is already done
in s5p_jpeg_find_format.
It was found by using v4l2-compliance tool and checking result
of VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS test
and using v4l2-ctl to get list of all supported formats.
Tested on s5pv210-galaxys (Samsung i9000 phone).
Fixes: bb677f3ac434 ("[media] Exynos4 JPEG codec v4l2 driver") Signed-off-by: Pawe? Chmiel <pawel.mikolaj.chmiel@gmail.com> Reviewed-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
[hverkuil-cisco@xs4all.nl: fix a few alignment issues] Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Aditya Pakki [Fri, 28 Dec 2018 18:37:36 +0000 (13:37 -0500)]
media: gspca: Check the return value of write_bridge for timeout
In po1030_probe(), m5602_write_bridge() can timeout and return an error
value. The fix checks for the return value and propagates upstream
consistent with other usb drivers.
Hans Verkuil [Tue, 18 Dec 2018 13:37:08 +0000 (08:37 -0500)]
media: v4l2-ctrls.c/uvc: zero v4l2_event
Control events can leak kernel memory since they do not fully zero the
event. The same code is present in both v4l2-ctrls.c and uvc_ctrl.c, so
fix both.
It appears that all other event code is properly zeroing the structure,
it's these two places.
Jacopo Mondi [Mon, 10 Dec 2018 14:53:55 +0000 (09:53 -0500)]
media: rcar-csi2: Fix PHTW table values for E3/V3M
The PHTW selection algorithm implemented in rcsi2_phtw_write_mbps() checks for
lower bound of the interval used to match the desired bandwidth. Use that
in place of the currently used upper bound.
media: usb: pwc: Don't use coherent DMA buffers for ISO transfer
DMA cocherency slows the transfer down on systems without hardware
coherent DMA.
Instead we use noncocherent DMA memory and explicit sync at data receive
handler.
Based on previous commit the following performance benchmarks have been
carried out. Average memcpy() data transfer rate (rate) and handler
completion time (time) have been measured when running video stream at
640x480 resolution at 10fps.
x86_64 based system (Intel Core i5-3470). This platform has hardware
coherent DMA support and proposed change doesn't make big difference here.
We see that the measurements agree within error ranges in this case.
So theoretically predicted performance downgrade cannot be reliably
measured here.
armv7l based system (TI AM335x BeagleBone Black @ 300MHz). This platform
has no hardware coherent DMA support. DMA coherence is implemented via
disabled page caching that slows down memcpy() due to memory controller
behaviour.
Note, that quantative difference leads (this commit leads to 3.3 times
acceleration) to qualitative behavior change in this case. As it was
stated before, the video stream cannot be successfully received at AM335x
platforms with MUSB based USB host controller due to performance issues
[1].
media: usb: pwc: Introduce TRACE_EVENTs for pwc_isoc_handler()
There were reports that PWC-based webcams don't work at some
embedded ARM platforms. [1] Isochronous transfer handler seems to
work too long leading to the issues in MUSB USB host subsystem.
Also note, that urb->giveback() handlers are still called with
disabled interrupts. In order to be able to measure performance of
PWC driver, traces are introduced in URB handler section.
media: s5p-mfc: fix incorrect bus assignment in virtual child device
Virtual MFC codec's child devices must not be assigned to platform bus,
because they are allocated as raw 'struct device' and don't have the
corresponding 'platform' part. This fixes NULL pointer access revealed
recently by commit a66d972465d1 ("devres: Align data[] to
ARCH_KMALLOC_MINALIGN").
Fixes: c79667dd93b0 ("media: s5p-mfc: replace custom reserved memory handling code with generic one") Reported-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A typo in code cleanup commit db9c1007bc07 ("media: lgdt330x: do
some cleanups at status logic") broke the FE_HAS_LOCK reporting
for 3303 chips by inadvertently modifying the register mask.
The broken lock status is critial as it prevents video capture
cards from reporting signal strength, scanning for channels,
and capturing video.
Fix regression by reverting mask change.
Cc: stable@vger.kernel.org # Kernel 4.17+ Fixes: db9c1007bc07 ("media: lgdt330x: do some cleanups at status logic") Signed-off-by: Nick French <naf@ou.edu> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by: Adam Stylinski <kungfujesus06@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Wed, 5 Dec 2018 10:30:55 +0000 (05:30 -0500)]
media: extended-controls.rst: update the mpeg2 compound controls
The layout of the compound controls has changed to fix
32/64 bit alignment issues and the use of timestamps instead of
buffer indices to refer to buffers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Wed, 24 Oct 2018 10:50:34 +0000 (06:50 -0400)]
media: videodev2.h: add v4l2_timeval_to_ns inline function
We want to be able to uniquely identify buffers for stateless
codecs. The internal timestamp (a u64) as stored internally in the
kernel is a suitable candidate for that, but in struct v4l2_buffer
it is represented as a struct timeval.
Add a v4l2_timeval_to_ns() function that converts the struct timeval
into a u64 in the same way that the kernel does. This makes it possible
to use this u64 elsewhere as a unique identifier of the buffer.
Since timestamps are also copied from the output buffer to the
corresponding capture buffer(s) by M2M devices, the u64 can be
used to refer to both output and capture buffers.
The plan is that in the future we redesign struct v4l2_buffer and use
u64 for the timestamp instead of a struct timeval (which has lots of
problems with 32 vs 64 bit and y2038 layout changes), and then there
is no more need to use this function.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Linus Torvalds [Mon, 7 Jan 2019 00:33:10 +0000 (16:33 -0800)]
Merge tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- improve boolinit.cocci and use_after_iter.cocci semantic patches
- fix alignment for kallsyms
- move 'asm goto' compiler test to Kconfig and clean up jump_label
CONFIG option
- generate asm-generic wrappers automatically if arch does not
implement mandatory UAPI headers
- remove redundant generic-y defines
- misc cleanups
* tag 'kbuild-v4.21-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: rename generated .*conf-cfg to *conf-cfg
kbuild: remove unnecessary stubs for archheader and archscripts
kbuild: use assignment instead of define ... endef for filechk_* rules
arch: remove redundant UAPI generic-y defines
kbuild: generate asm-generic wrappers if mandatory headers are missing
arch: remove stale comments "UAPI Header export list"
riscv: remove redundant kernel-space generic-y
kbuild: change filechk to surround the given command with { }
kbuild: remove redundant target cleaning on failure
kbuild: clean up rule_dtc_dt_yaml
kbuild: remove UIMAGE_IN and UIMAGE_OUT
jump_label: move 'asm goto' support test to Kconfig
kallsyms: lower alignment on ARM
scripts: coccinelle: boolinit: drop warnings on named constants
scripts: coccinelle: check for redeclaration
kconfig: remove unused "file" field of yylval union
nds32: remove redundant kernel-space generic-y
nios2: remove unneeded HAS_DMA define
Linus Torvalds [Mon, 7 Jan 2019 00:30:14 +0000 (16:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf tooling updates form Ingo Molnar:
"A final batch of perf tooling changes: mostly fixes and small
improvements"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
perf session: Add comment for perf_session__register_idle_thread()
perf thread-stack: Fix thread stack processing for the idle task
perf thread-stack: Allocate an array of thread stacks
perf thread-stack: Factor out thread_stack__init()
perf thread-stack: Allow for a thread stack array
perf thread-stack: Avoid direct reference to the thread's stack
perf thread-stack: Tidy thread_stack__bottom() usage
perf thread-stack: Simplify some code in thread_stack__process()
tools gpio: Allow overriding CFLAGS
tools power turbostat: Override CFLAGS assignments and add LDFLAGS to build command
tools thermal tmon: Allow overriding CFLAGS assignments
tools power x86_energy_perf_policy: Override CFLAGS assignments and add LDFLAGS to build command
perf c2c: Increase the HITM ratio limit for displayed cachelines
perf c2c: Change the default coalesce setup
perf trace beauty ioctl: Beautify USBDEVFS_ commands
perf trace beauty: Export function to get the files for a thread
perf trace: Wire up ioctl's USBDEBFS_ cmd table generator
perf beauty ioctl: Add generator for USBDEVFS_ ioctl commands
tools headers uapi: Grab a copy of usbdevice_fs.h
perf trace: Store the major number for a file when storing its pathname
...
Linus Torvalds [Sun, 6 Jan 2019 01:50:59 +0000 (17:50 -0800)]
Change mincore() to count "mapped" pages rather than "cached" pages
The semantics of what "in core" means for the mincore() system call are
somewhat unclear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache" rather than "page is mapped in the mapping".
The problem with that traditional semantic is that it exposes a lot of
system cache state that it really probably shouldn't, and that users
shouldn't really even care about.
So let's try to avoid that information leak by simply changing the
semantics to be that mincore() counts actual mapped pages, not pages
that might be cheaply mapped if they were faulted (note the "might be"
part of the old semantics: being in the cache doesn't actually guarantee
that you can access them without IO anyway, since things like network
filesystems may have to revalidate the cache before use).
In many ways the old semantics were somewhat insane even aside from the
information leak issue. From the very beginning (and that beginning is
a long time ago: 2.3.52 was released in March 2000, I think), the code
had a comment saying
Later we can get more picky about what "in core" means precisely.
and this is that "later". Admittedly it is much later than is really
comfortable.
NOTE! This is a real semantic change, and it is for example known to
change the output of "fincore", since that program literally does a
mmmap without populating it, and then doing "mincore()" on that mapping
that doesn't actually have any pages in it.
I'm hoping that nobody actually has any workflow that cares, and the
info leak is real.
We may have to do something different if it turns out that people have
valid reasons to want the old semantics, and if we can limit the
information leak sanely.
Cc: Kevin Easton <kevin@guarana.org> Cc: Jiri Kosina <jikos@kernel.org> Cc: Masatake YAMATO <yamato@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Jan 2019 19:15:04 +0000 (11:15 -0800)]
Fix 'acccess_ok()' on alpha and SH
Commit 594cc251fdd0 ("make 'user_access_begin()' do 'access_ok()'")
broke both alpha and SH booting in qemu, as noticed by Guenter Roeck.
It turns out that the bug wasn't actually in that commit itself (which
would have been surprising: it was mostly a no-op), but in how the
addition of access_ok() to the strncpy_from_user() and strnlen_user()
functions now triggered the case where those functions would test the
access of the very last byte of the user address space.
The string functions actually did that user range test before too, but
they did it manually by just comparing against user_addr_max(). But
with user_access_begin() doing the check (using "access_ok()"), it now
exposed problems in the architecture implementations of that function.
For example, on alpha, the access_ok() helper macro looked like this:
and what it basically tests is of any of the high bits get set (the
USER_DS masking value is 0xfffffc0000000000).
And that's completely wrong for the "addr+size" check. Because it's
off-by-one for the case where we check to the very end of the user
address space, which is exactly what the strn*_user() functions do.
Why? Because "addr+size" will be exactly the size of the address space,
so trying to access the last byte of the user address space will fail
the __access_ok() check, even though it shouldn't. As a result, the
user string accessor functions failed consistently - because they
literally don't know how long the string is going to be, and the max
access is going to be that last byte of the user address space.
Side note: that alpha macro is buggy for another reason too - it re-uses
the arguments twice.
And SH has another version of almost the exact same bug:
#define __addr_ok(addr) \
((unsigned long __force)(addr) < current_thread_info()->addr_limit.seg)
so far so good: yes, a user address must be below the limit. But then:
is wrong with the exact same off-by-one case: the case when "addr+size"
is exactly _equal_ to the limit is actually perfectly fine (think "one
byte access at the last address of the user address space")
The SH version is actually seriously buggy in another way: it doesn't
actually check for overflow, even though it did copy the _comment_ that
talks about overflow.
So it turns out that both SH and alpha actually have completely buggy
implementations of access_ok(), but they happened to work in practice
(although the SH overflow one is a serious serious security bug, not
that anybody likely cares about SH security).
This fixes the problems by using a similar macro on both alpha and SH.
It isn't trying to be clever, the end address is based on this logic:
unsigned long __ao_end = __ao_a + __ao_b - !!__ao_b;
which basically says "add start and length, and then subtract one unless
the length was zero". We can't subtract one for a zero length, or we'd
just hit an underflow instead.
For a lot of access_ok() users the length is a constant, so this isn't
actually as expensive as it initially looks.
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net> Cc: Matt Turner <mattst88@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>