Philipp Zabel [Fri, 27 Apr 2018 16:19:17 +0000 (12:19 -0400)]
media: coda: set colorimetry on coded queue
Do not set context colorimetry on the raw (OUTPUT) queue for encoders.
Always set colorimetry on the coded queue (CAPTURE for encoders, OUTPUT
for decoders).
This also skips propagation of capture queue format and selection
rectangle on S_FMT(OUTPUT) to the CAPTURE queue for encoders.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Philipp Zabel [Fri, 27 Apr 2018 16:19:16 +0000 (12:19 -0400)]
media: coda: do not try to propagate format if capture queue busy
The driver helpfully resets the capture queue format and selection
rectangle whenever output format is changed. This only works while
the capture queue is not busy.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: sta2x11: Use gpio_is_valid() and remove unnecessary check
Replace the manual validity checks for the GPIO with the
gpio_is_valid().
In vip_gpio_reserve(), Error checking for gpio pin is not correct.
If pwr_pin = -1, It will return 0. This should be return an error.
In sta2x11_vip_init_one(), Error checking for gpio 'reset_pin'
is unnecessary. Because vip_gpio_reserve() is also checking for
valid gpio pin. So removed extra error checking for gpio 'reset_pin'.
Dan Carpenter [Fri, 20 Apr 2018 10:13:52 +0000 (06:13 -0400)]
media: vpbe_venc: potential uninitialized variable in ven_sub_dev_init()
Smatch complains that "venc" could be uninitialized. There are a couple
of error paths where it looks like maybe that could happen. I don't know
if it's really a bug, but it's reasonable to set "venc" to NULL and
silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Hans Verkuil [Fri, 20 Apr 2018 08:13:53 +0000 (04:13 -0400)]
media: cec-gpio: use GPIOD_OUT_HIGH_OPEN_DRAIN
This driver needs a pull up output GPIO, but devm_gpiod_get() is called
with GPIOD_IN. This apparently works fine for the RPi3 where the DT
correctly specifies a pull up GPIO, but on the i.MX6 it also needs to
be specified with devm_gpiod_get().
Reported-by: Henrik Mau <Henrik.Mau@linn.co.uk> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
Reference id -> 1c8f422059ae ("mm: change return type to
vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Simon Que [Mon, 9 Apr 2018 19:47:38 +0000 (15:47 -0400)]
media: v4l2-core: Rename array 'video_driver' to 'video_drivers'
Improves code clarity in two ways:
1. The plural name makes it more clear that it is an array.
2. The name of the array is now no longer identical to the struct type
name, so it is easier to find in the code.
Signed-off-by: Simon Que <sque@chromium.org> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Bingbu Cao [Mon, 30 Apr 2018 14:30:40 +0000 (10:30 -0400)]
media: intel-ipu3: cio2: Handle IRQs until INT_STS is cleared
Interrupt behavior shows that some time the frame end and frame start of
next frame is unstable and can range from several to hundreds of
micro-sec. In the case of ~10us, isr may not clear next sof interrupt
status in single handling, which prevents new interrupts from coming.
Fix this by handling all pending IRQs before exiting isr, so any abnormal
behavior results from very short interrupt status changes is protected.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com> Signed-off-by: Andy Yeh <andy.yeh@intel.com> Signed-off-by: Yong Zhi <yong.zhi@intel.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/video/fbdev/omap2/omapfb/omapfb-main.c: In function 'omapfb_init_connections':
>> drivers/video/fbdev/omap2/omapfb/omapfb-main.c:2396:8: error: implicit declaration of function 'omapdss_find_mgr_from_display' [-Werror=implicit-function-declaration]
mgr = omapdss_find_mgr_from_display(def_dssdev);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/video/fbdev/omap2/omapfb/omapfb-main.c:2396:6: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
mgr = omapdss_find_mgr_from_display(def_dssdev);
^
drivers/video/fbdev/omap2/omapfb/omapfb-main.c: In function 'omapfb_find_default_display':
>> drivers/video/fbdev/omap2/omapfb/omapfb-main.c:2430:13: error: implicit declaration of function 'omapdss_get_default_display_name' [-Werror=implicit-function-declaration]
def_name = omapdss_get_default_display_name();
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/video/fbdev/omap2/omapfb/omapfb-main.c:2430:11: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
def_name = omapdss_get_default_display_name();
^
Hans de Goede [Sat, 5 May 2018 08:22:08 +0000 (04:22 -0400)]
media: gspca: Stop using GFP_DMA for buffers for USB bulk transfers
The recent "x86 ZONE_DMA love" discussion at LSF/MM pointed out that some
gspca sub-drivvers are using GFP_DMA to allocate buffers which are used
for USB bulk transfers, there is absolutely no need for this, drop it.
Cc: "Luis R. Rodriguez" <mcgrof@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: rcar-vin: enable field toggle after a set number of lines for Gen3
The VIN Gen3 hardware don't have Line Post-Clip capabilities as VIN Gen2
hardware have. To protect against writing outside the capture window
enable field toggle after a set number of lines have been captured.
Capturing outside the allocated capture buffer where observed on R-Car
Gen3 Salvator-XS H3 from the CVBS input if the standard is
misconfigured. That is if a PAL source is connected to the system but
the adv748x standard is set to NTSC. In this case the format reported by
the adv748x is 720x480 and that is what is used for the media pipeline.
The PAL source generates frames in the format of 720x576 and the field
is not toggled until the VSYNC is detected and at that time data have
already been written outside the allocated capture buffer.
With this change the capture in the situation described above results in
garbage frames but that is far better then writing outside the capture
buffer.
The compatible string "renesas,rcar-gen3-vin" was added before the
Gen3 driver code was added but it's not possible to use. Each SoC in the
Gen3 series require SoC specific knowledge in the driver to function.
Remove it before it is added to any device tree descriptions.
media: cx88: Get rid of spurious call to cx8800_start_vbi_dma()
This was left over from the conversion to VB2, where the call was
getting invoked both in buffer_queue and start_streaming, which
was intermittently causing invalid opcodes on the VBI RISC queue.
This change effectively mirrors the exact same change Hans Verkuil
made in cx88-video.c in commit 389208e1173e ("[media] cx88:
remove leftover start_video_dma() call").
Thanks to Daniel Glöckner for spotting the actual bug after I spent
several days trying to chase down the issue.
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Fix this by returning 'netdev_tx_t' in this driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: frontends: fix ops get_algo()'s return type
The method dvb_frontend_ops::get_frontend_algo() is defined as
returning an 'enum dvbfe_algo', but the implementation in this
driver returns an 'int'.
Fix this by returning 'enum dvbfe_algo' on drivers.
[mchehab+samsung@kernel.org: merge similar patches and patch
ddbridge-mci.c the same way] Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Anders Roxell [Mon, 23 Apr 2018 19:31:39 +0000 (15:31 -0400)]
media: drivers: media: platform: make VIDEO_VIU depend on I2C
Commit 7378f1149884 ("media: omap2: omapfb: allow building it with
COMPILE_TEST") broke compilation without CONFIG_I2C selected.
drivers/media/platform/fsl-viu.c: In function ‘viu_of_probe’:
drivers/media/platform/fsl-viu.c:1452:7: error: implicit declaration of function ‘i2c_get_adapter’; did you mean ‘i2c_lock_adapter’? [-Werror=implicit-function-declaration]
ad = i2c_get_adapter(0);
^~~~~~~~~~~~~~~
i2c_lock_adapter
drivers/media/platform/fsl-viu.c:1452:5: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
ad = i2c_get_adapter(0);
^
drivers/media/platform/fsl-viu.c:1534:2: error: implicit declaration of function ‘i2c_put_adapter’; did you mean ‘i2c_lock_adapter’? [-Werror=implicit-function-declaration]
i2c_put_adapter(ad);
^~~~~~~~~~~~~~~
i2c_lock_adapter
Added I2C dependency in order to make all configurations work again.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit ee93340e98bc ("media: ngene: deduplicate I2C adapter evaluation")
added a helper to evaluate the I2C adapter to be used for demod/tuner
attachment based on the given ngene_channel, and that helper is used in
many attach functions to initialise the i2c_adapter variable. However,
for some reason in tuner_attach_stv6110() and demod_attach_stv0900(), the
adapter evaluation wasn't removed as in all other functions. Fix (or
finalize, even) the helper use by cleaning up the superfluous I2C adapter
evaluation leftover in these two functions.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Colin Ian King [Wed, 18 Apr 2018 15:06:17 +0000 (11:06 -0400)]
media: include/media: fix missing | operator when setting cfg
The value from a readl is being masked with ITE_REG_CIOCAN_MASK however
this is not being used and cfg is being re-assigned. I believe the
assignment operator should actually be instead the |= operator.
Detected by CoverityScan, CID#1467987 ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
media: tuners: add new i2c driver for Sharp qm1d1b0004 ISDB-S tuner
The tuner is used in Earthsoft PT1/PT2 DVB boards,
and the driver was extraced from (the former) va1j5jf8007s.c of PT1.
it might contain PT1 specific configs.
This patch adds a PLL "description" of Philips TDA6651 for ISDB-T.
It was extracted from (the former) va1j5jf8007t.c of EarthSoft PT1,
thus the desc might include PT1 specific configs.
media: dvb-usb-v2/gl861: use usleep_range() for short delay
As the kernel doc "timers-howto.txt" reads,
short delay with msleep() can take much longer.
In a case of raspbery-pi platform where CONFIG_HZ_100 was set,
it actually affected the init of Friio devices
since it issues lots of i2c transactions with short delay.
media: i2c: tvp5150: Use the correct comment style
This patch resolves checkpatch.pl warnings:
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
Samuel Williams [Sun, 1 Apr 2018 15:00:27 +0000 (11:00 -0400)]
media: bttv: Fixed oops error when capturing at yuv410p
When capturing at yuv410p, sg_next was called too many times when chroma is
false, eventually returning NULL. This patch does fix this for my hardware.
Signed-off-by: Samuel Williams <sam8641@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Daniel Scheller [Sat, 17 Mar 2018 14:55:32 +0000 (10:55 -0400)]
media: ddbridge, cxd2099: include guard, fix unneeded NULL init, strings
Three really tiny minors in this single commit which all on their own
would just clutter up the commit history unnecessarily:
* ddbridge-regs.h is lacking an include guard. Add it.
* Fix an unnecessary NULL initialisation in ddbridge-ci. The declaration
of the ci struct ptr is immediately followed by kzalloc().
* Clarify that the CXD2099AR is a Sony device in the cxd2099 driver at a
few places including Kconfig.
The -Warray-bounds warning in gcc-8 triggers for a newly added file:
drivers/media/spi/cxd2880-spi.c: In function 'cxd2880_write_reg':
drivers/media/spi/cxd2880-spi.c:111:3: error: 'memcpy' forming offset [133, 258] is out of the bounds [0, 132] of object 'send_data' with type 'u8[132]' {aka 'unsigned char[132]'} [-Werror=array-bounds]
The problem appears to be that we have two range checks in this function,
first comparing against BURST_WRITE_MAX (128) and then comparing against
a literal '255'. The logic checking the buffer size looks at the second
one and decides that this might be the actual maximum data length.
This is understandable behavior from the compiler, but the code is actually
safe. Since the first check is already shorter, we can remove the loop
and only leave that. To be on the safe side in case BURST_WRITE_MAX might
be increased, I'm leaving the check against U8_MAX.
Fixes: bd24fcddf6b8 ("media: cxd2880-spi: Add support for CXD2880 SPI interface") Cc: Martin Sebor <msebor@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Yasunari Takiguchi <Yasunari.Takiguchi@sony.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If state is not initialized or is freed, we can't use it:
drivers/media/dvb-frontends/lgdt330x.c:920 lgdt330x_probe() error: potential null dereference 'state'. (kzalloc returns null)
drivers/media/dvb-frontends/lgdt330x.c:920 lgdt330x_probe() error: we previously assumed 'state' could be null (see line 878)
drivers/media/dvb-frontends/lgdt330x.c:920 lgdt330x_probe() error: dereferencing freed memory 'state'
Fixes: 23ba635d45f5 ("media: lgdt330x: convert it to the new I2C binding way") Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Please notice that there's no scale indication at the driver.
As we don't have the datasheet, let's assume that it is receiving
data at a rate of 10.000 packets per second. Ideally, this should
be read or estimated.
In order to avoid flooding I2C bus with data, the maximum
polling rate for those stats was set to 1 second.
As we're about to convert this driver to use the new i2c
binding way, let's first solve most coding style issues,
in order to avoid mixing coding style changes with code
changes.
Commit be7fd3c3a8c5 ("media: em28xx: Hauppauge DualHD second tuner
functionality") removed the logic with sets the alternate for the DVB
device. Without setting the right alternate, the device won't be
able to submit URBs, and userspace fails with -EMSGSIZE:
ERROR DMX_SET_PES_FILTER failed (PID = 0x2000): 90 Message too long
Daniel Scheller [Mon, 9 Apr 2018 16:47:50 +0000 (12:47 -0400)]
media: ddbridge: add hardware defs and PCI IDs for MCI cards
Add PCI IDs and ddb_info for the new MCI-based MaxSX8 cards. Also add
needed defines so the cards can be hooked up into ddbridge's probe and
attach handling.
Picked up from the upstream dddvb-0.9.33 release.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>