Arnd Bergmann [Mon, 14 May 2012 13:24:45 +0000 (15:24 +0200)]
Merge branch 'imx/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6.git into next/dt2
Shawn Guo <shawn.guo@linaro.org> writes:
I chose to base it on Sascha's imx-common-clk series than -rc, because
otherwise it will keep patching clock file that has been removed by
imx-common-clk series. It also depends on imx-pinctrl pull-request
I just sent to be functional.
Note: when imx-common-clk and imx-pinctrl get merged together, the
following files will have conflicts. But the conflicts should not be
so hard to resolve.
[arnd: resolved those merge conflicts by pulling pinctrl branch]
* imx/dt: (24 commits)
ARM: dts: imx53-qsb: enable audio support
ARM: dts: imx51-babbage: enable audio support
ARM: imx: add audio codec clk lookup for imx53-qsb
ARM: imx: add audmux pad setting for imx51-babbage
ARM: imx: add more imx5 ssi clocks
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
ARM: dts: imx6q-sabrelite: add serial2 pinctrl support
ARM: dts: imx6q-sabrelite: add sound device imx6q-sabrelite-sgtl5000
ARM: imx6q_sabrelite: clk_register_clkdev cko1 for sgtl5000
ARM: imx6q: add ssi1_ipg clk_lookup
ARM: dts: imx6q-sabrelite: add audmux pinctrl support
ARM: dts: imx6q-sabrelite: add i2c1 pinctrl support
ARM: dts: imx6q-sabrelite: add audmux device
ARM: dts: imx6q-sabrelite: add ssi device
ARM: dts: imx6q-arm2: add pinctrl state for usdhc
ARM: imx6: Add UART2 for low-level debug
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
ARM: imx6q: move imx6q_sabrelite specific code to a dedicated function
ARM: dts: imx6q-sabrelite: Add SPI NOR support
ARM: dts: Add basic support for imx6q-sabresd
...
Pulls in imx/pinctrl and imx/clock as dependencies.
Olof Johansson [Sun, 13 May 2012 05:33:24 +0000 (22:33 -0700)]
Merge branch 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt2
* 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (51 commits)
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
ARM: dts: enable mmc for imx23-evk
mmc: mxs-mmc: add device tree support
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
mmc: mxs-mmc: use devm_* helper to make cleanup simpler
mmc: mxs-mmc: move header from mach into linux folder
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
mmc: mxs-mmc: let ssp_is_old take host as parameter
mmc: mxs-mmc: use global stmp_device functionality
ARM: mxs: add gpio support for device tree boot
gpio/mxs: add device tree probe
gpio/mxs: get rid of the use of cpu_is_xxx
gpio/mxs: use devm_* helpers to make error handling simple
ARM: mxs: add mxs-dma dt support
ARM: mxs: do not add dma device by default
dma: mxs-dma: add device tree probe support
...
Shawn Guo [Sun, 6 May 2012 05:33:40 +0000 (13:33 +0800)]
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
Copy wp_gpio from platform_data into struct mxs_mmc_host, so that
the use of platform_data can be limited in probe function, which
will ease the device tree probe.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Sun, 6 May 2012 03:25:35 +0000 (11:25 +0800)]
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
It replaces dma_res with dma_channel in struct mxs_mmc_host, so that
the device tree support will be a little easier, since dma channel
can not be retrieved from "struct resource *dma_res".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Sat, 5 May 2012 12:24:01 +0000 (20:24 +0800)]
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
The register HW_SSP_VERSION is broken for ssp version detection,
as the address of the register is different between imx23 and imx28.
Let's use platform_device_id to detect the device, so that the use
of cpu_is_xxx can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Chris Ball <cjb@laptop.org>
Shawn Guo [Thu, 3 May 2012 15:32:52 +0000 (23:32 +0800)]
gpio/mxs: get rid of the use of cpu_is_xxx
It removes the use of cpu_is_xxx from gpio-mxs driver and instead use
platform_device_id to identify the device. Accordingly, mxs platform
code is changed to register gpio device with different names, and
the registeration are done in soc specific initialization functions
now, so postcore_initcall(mxs_add_mxs_gpio) gets removed.
Shawn Guo [Wed, 9 May 2012 22:23:26 +0000 (06:23 +0800)]
dma: mxs-dma: make platform_device_id more generic
Rewrite mxs_dma_is_apbh and mxs_dma_is_apbx in order to support
other SoCs like imx6q and reform the platform_device_id for the
better further dt support.
Cc: Dan Williams <dan.j.williams@intel.com> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Huang Shijie <b32955@freescale.com> Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Marek Vasut <marex@denx.de> Acked-by: Vinod Koul <vinod.koul@intel.com>
Shawn Guo [Sun, 6 May 2012 12:24:04 +0000 (20:24 +0800)]
net: fec: adopt pinctrl support
Cc: netdev@vger.kernel.org Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Acked-by: Dong Aisheng <dong.aisheng@linaro.org> Acked-by: David S. Miller <davem@davemloft.net>
ARM: dts: imx53-qsb: Add Dialog DA9053 PMIC support
Add Dialog DA9053 regulators support for imx53-qsb (Loco board)
Cc: Sascha Hauer <kernel@pengutronix.de> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: Amit Kucheria <amit.kucheria@canonical.com> Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org> Cc: Russell King - ARM Linux <linux@arm.linux.org.uk> Signed-off-by: Ying-Chun Liu (PaulLiu) <paulliu@debian.org> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo [Tue, 8 May 2012 13:39:33 +0000 (21:39 +0800)]
ARM: imx6q: register phy fixup only when CONFIG_PHYLIB is enabled
It fixes the following compile error with network disabled in
imx_v6_v7_defconfig.
arch/arm/mach-imx/built-in.o: In function `ksz9021rn_phy_fixup':
imx53-dt.c:(.text+0x5f70): undefined reference to `mdiobus_write'
imx53-dt.c:(.text+0x5f84): undefined reference to `mdiobus_write'
imx53-dt.c:(.text+0x5f98): undefined reference to `mdiobus_write'
imx53-dt.c:(.text+0x5fac): undefined reference to `mdiobus_write'
imx53-dt.c:(.text+0x5fc0): undefined reference to `mdiobus_write'
arch/arm/mach-imx/built-in.o: In function `imx6q_init_machine':
imx53-dt.c:(.init.text+0x387c): undefined reference to `phy_register_fixup_for_uid'
make: *** [.tmp_vmlinux1] Error 1
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Shawn Guo [Sun, 6 May 2012 14:14:13 +0000 (22:14 +0800)]
ARM: mxs: enable pinctrl dummy states
The mxs pinctrl driver will only support DT probe. That said, the mxs
device drivers can only get pinctrl state from pinctrl subsystem when
the drivers get probed from device tree.
Before converting the whole mxs platform support over to device tree,
we need to enable pinctrl dummy states for those non-DT board files
to ensure the pinctrl API adopted by mxs device drivers will work for
both DT and non-DT probe.
Instead of calling pinctrl_provide_dummies() directly in every board
file, the patch introduces soc specific calls mx23_soc_init() and
mx28_soc_init() for boards' .init_machine hook to invoke, so that
any soc specific setup for non-DT boot only can be added there.
Linus Torvalds [Sun, 6 May 2012 19:19:38 +0000 (12:19 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes form Peter Anvin
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_mid_powerbtn: mark irq as IRQF_NO_SUSPEND
arch/x86/platform/geode/net5501.c: change active_low to 0 for LED driver
x86, relocs: Remove an unused variable
asm-generic: Use __BITS_PER_LONG in statfs.h
x86/amd: Re-enable CPU topology extensions in case BIOS has disabled it
Linus Torvalds [Sun, 6 May 2012 17:20:07 +0000 (10:20 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"The big ones here are a memory leak we introduced in rc1, and a
scheduling while atomic if the transid on disk doesn't match the
transid we expected. This happens for corrupt blocks, or out of date
disks.
It also fixes up the ioctl definition for our ioctl to resolve logical
inode numbers. The __u32 was a merging error and doesn't match what
we ship in the progs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: avoid sleeping in verify_parent_transid while atomic
Btrfs: fix crash in scrub repair code when device is missing
btrfs: Fix mismatching struct members in ioctl.h
Btrfs: fix page leak when allocing extent buffers
Btrfs: Add properly locking around add_root_to_dirty_list
Al Viro [Sun, 6 May 2012 16:20:00 +0000 (17:20 +0100)]
x86: fix broken TASK_SIZE for ia32_aout
Setting TIF_IA32 in load_aout_binary() used to be enough; these days
TASK_SIZE is controlled by TIF_ADDR32 and that one doesn't get set
there. Switch to use of set_personality_ia32()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Mason [Sun, 6 May 2012 11:23:47 +0000 (07:23 -0400)]
Btrfs: avoid sleeping in verify_parent_transid while atomic
verify_parent_transid needs to lock the extent range to make
sure no IO is underway, and so it can safely clear the
uptodate bits if our checks fail.
But, a few callers are using it with spinlocks held. Most
of the time, the generation numbers are going to match, and
we don't want to switch to a blocking lock just for the error
case. This adds an atomic flag to verify_parent_transid,
and changes it to return EAGAIN if it needs to block to
properly verifiy things.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Linus Torvalds [Sat, 5 May 2012 23:34:38 +0000 (16:34 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha
Pull alpha fixes from Matt Turner:
"My alpha tree is back up (after taking quite some time to get my GPG
key signed). It contains just some simple fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: silence 'const' warning in sys_marvel.c
alpha: include module.h to fix modpost on Tsunami
alpha: properly define get/set_rtc_time on Marvel/SMP
alpha: VGA_HOSE depends on VGA_CONSOLE
Jiri Slaby [Sat, 5 May 2012 20:49:10 +0000 (22:49 +0200)]
TTY: pdc_cons, fix regression in close
The test in pdc_console_tty_close '!tty->count' was always wrong
because tty->count is decremented after tty->ops->close is called and
thus can never be zero. Hence the 'then' branch was never executed and
the timer never deleted.
This did not matter until commit 5dd5bc40f3b6 ("TTY: pdc_cons, use
tty_port"). There we needed to set TTY in tty_port to NULL, but this
never happened due to the bug above.
So change the test to really trigger at the last close by changing the
condition to 'tty->count == 1'.
Well, the driver should not touch tty->count at all. It should use
tty_port->count and count open count there itself.
Linus Torvalds [Sat, 5 May 2012 17:07:06 +0000 (10:07 -0700)]
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound sound fixes from Takashi Iwai:
"As good as nothing exciting here; just a few trivial fixes for various
ASoC stuff."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: omap-pcm: Free dma buffers in case of error.
ASoC: s3c2412-i2s: Fix dai registration
ASoC: wm8350: Don't use locally allocated codec struct
ASoC: tlv312aic23: unbreak resume
ASoC: bf5xx-ssm2602: Set DAI format
ASoC: core: check of_property_count_strings failure
ASoC: dt: sgtl5000.txt: Add description for 'reg' field
ASoC: wm_hubs: Make sure we don't disable differential line outputs
Sasha Levin [Sat, 5 May 2012 15:06:35 +0000 (17:06 +0200)]
init: don't try mounting device as nfs root unless type fully matches
Currently, we'll try mounting any device who's major device number is
UNNAMED_MAJOR as NFS root. This would happen for non-NFS devices as
well (such as 9p devices) but it wouldn't cause any issues since
mounting the device as NFS would fail quickly and the code proceeded to
doing the proper mount:
[ 101.522716] VFS: Unable to mount root fs via NFS, trying floppy.
[ 101.534499] VFS: Mounted root (9p filesystem) on device 0:18.
Commit 6829a048102a ("NFS: Retry mounting NFSROOT") introduced retries
when mounting NFS root, which means that now we don't immediately fail
and instead it takes an additional 90+ seconds until we stop retrying,
which has revealed the issue this patch fixes.
This meant that it would take an additional 90 seconds to boot when
we're not using a device type which gets detected in order before NFS.
This patch modifies the NFS type check to require device type to be
'Root_NFS' instead of requiring the device to have an UNNAMED_MAJOR
major. This makes boot process cleaner since we now won't go through
the NFS mounting code at all when the device isn't an NFS root
("/dev/nfs").
Lin Ming [Mon, 23 Apr 2012 01:03:49 +0000 (09:03 +0800)]
ACPI: Fix D3hot v D3cold confusion
Before this patch, ACPI_STATE_D3 incorrectly referenced D3hot
in some places, but D3cold in other places.
After this patch, ACPI_STATE_D3 always means ACPI_STATE_D3_COLD;
and all references to D3hot use ACPI_STATE_D3_HOT.
ACPI's _PR3 method is used to enter both D3hot and D3cold states.
What distinguishes D3hot from D3cold is the presence _PR3
(Power Resources for D3hot) If these resources are all ON,
then the state is D3hot. If _PR3 is not present,
or all _PR0 resources for the devices are OFF,
then the state is D3cold.
This patch applies after Linux-3.4-rc1.
A future syntax cleanup may remove ACPI_STATE_D3
to emphasize that it always means ACPI_STATE_D3_COLD.
Signed-off-by: Lin Ming <ming.m.lin@intel.com> Acked-by: Rafael J. Wysocki <rjw@sisk.pl> Reviewed-by: Aaron Lu <aaron.lu@amd.com> Signed-off-by: Len Brown <len.brown@intel.com>
Commit ec81aecb2966 ("hfs: fix a potential buffer overflow") fixed a few
potential buffer overflows in the hfs filesystem. But as Timo Warns
pointed out, these changes also need to be made on the hfsplus
filesystem as well.
Reported-by: Timo Warns <warns@pre-sense.de> Acked-by: WANG Cong <amwang@redhat.com> Cc: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: Miklos Szeredi <mszeredi@suse.cz> Cc: Sage Weil <sage@newdream.net> Cc: Eugene Teo <eteo@redhat.com> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Dave Anderson <anderson@redhat.com> Cc: stable <stable@vger.kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>