David S. Miller [Fri, 26 Apr 2019 20:05:52 +0000 (16:05 -0400)]
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Weihang Li [Thu, 25 Apr 2019 12:42:55 +0000 (20:42 +0800)]
net: hns3: remove reset after command send failed
It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: Weihang Li <liweihang@hisilicon.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 25 Apr 2019 12:42:54 +0000 (20:42 +0800)]
net: hns3: prevent double free in hns3_put_ring_config()
This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: hns3: extend the loopback state acquisition time
The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).
If not modified, the loopback test returns probability failure.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 25 Apr 2019 12:42:52 +0000 (20:42 +0800)]
net: hns3: fix pause configure fail problem
When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375bf7 ("net: hns3: do not return GE PFC setting err when initializing") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 25 Apr 2019 12:42:51 +0000 (20:42 +0800)]
net: hns3: not reset TQP in the DOWN while VF resetting
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 25 Apr 2019 12:42:50 +0000 (20:42 +0800)]
net: hns3: use a reserved byte to identify need_resp flag
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan [Thu, 25 Apr 2019 12:42:49 +0000 (20:42 +0800)]
net: hns3: use atomic_t replace u32 for arq's count
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e77 ("net: hns3: stop sending keep alive msg to PF when VF is resetting") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 25 Apr 2019 12:42:47 +0000 (20:42 +0800)]
net: hns3: handle the BD info on the last BD of the packet
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 25 Apr 2019 12:42:46 +0000 (20:42 +0800)]
net: hns3: fix for TX clean num when cleaning TX BD
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Thu, 25 Apr 2019 12:42:45 +0000 (20:42 +0800)]
net: hns3: fix data race between ring->next_to_clean
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Device may be shutdown without the hardware being reinitialized, in
which case we want to ensure we cleanup properly.
This is especially important for kexec with traffic flowing.
The shutdown procedures resembles the remove procedures, so we can reuse
those common tasks.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
NFC: st95hf: remove set but not used variables 'dev, nfcddev'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/nfc/st95hf/core.c: In function 'st95hf_irq_thread_handler':
drivers/nfc/st95hf/core.c:786:26: warning:
variable 'nfcddev' set but not used [-Wunused-but-set-variable]
drivers/nfc/st95hf/core.c:784:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
They are never used since introduction in
commit cab47333f0f7 ("NFC: Add STMicroelectronics ST95HF driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 25 Apr 2019 00:21:40 +0000 (17:21 -0700)]
tipc: remove rcu_read_unlock() left in tipc_udp_recv()
I forgot to remove one rcu_read_unlock() before a return statement.
Joy of mixing goto and return styles in a function :)
Fixes: 4109a2c3b91e ("tipc: tipc_udp_recv() cleanup vs rcu verbs") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
All Apple products use the same protocol for tethering over USB.
To simplify the code and make it future proof, use
USB_VENDOR_AND_INTERFACE_INFO() instead of
USB_DEVICE_AND_INTERFACE_INFO() to automatically detect and support
all existing and future Apple products using the same interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: b1d40991506aa ("ipv6: Rename fib6_multipath_select and pass fib6_result") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cnic: Refactor code and mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, refactor code a
bit and mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/broadcom/cnic.c: In function ‘cnic_cm_process_kcqe’:
drivers/net/ethernet/broadcom/cnic.c:4044:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
opcode = L4_KCQE_OPCODE_VALUE_CLOSE_COMP;
drivers/net/ethernet/broadcom/cnic.c:4050:2: note: here
case L4_KCQE_OPCODE_VALUE_RESET_RECEIVED:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4/cxgb4vf_main: Mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c: In function ‘fwevtq_handler’:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:520:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpl = (void *)p;
~~~~^~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:524:2: note: here
case CPL_SGE_EGR_UPDATE: {
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
wimax/i2400m/control: Mark expected switch fall-through
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
In file included from drivers/net/wimax/i2400m/debug-levels.h:30,
from drivers/net/wimax/i2400m/control.c:86:
drivers/net/wimax/i2400m/control.c: In function ‘i2400m_report_tlv_system_state’:
./include/linux/wimax/debug.h:200:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
do { \
^
./include/linux/wimax/debug.h:404:36: note: in expansion of macro ‘_d_printf’
#define d_printf(l, _dev, f, a...) _d_printf(l, "", _dev, f, ## a)
^~~~~~~~~
drivers/net/wimax/i2400m/control.c:354:3: note: in expansion of macro ‘d_printf’
d_printf(1, dev, "entering BS-negotiated idle mode\n");
^~~~~~~~
drivers/net/wimax/i2400m/control.c:355:2: note: here
case I2400M_SS_DISCONNECTING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-drv.c: In function ‘xgbe_set_hwtstamp_settings’:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1614:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1616:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1625:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1627:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1636:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1638:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: socket: Fix missing break in switch statement
Add missing break statement in order to prevent the code from falling
through to cases SIOCGSTAMP_NEW and SIOCGSTAMPNS_NEW.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 0768e17073dc ("net: socket: implement 64-bit timestamps") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: trust non-IP cast type in qeth_l3_fill_header()
When building the L3 HW header for non-IP packets, trust the cast type
that was passed as parameter. qeth_l3_get_cast_type() has most likely
also used h_dest to determine the cast type, so we get the same
result, and can remove that duplicated code.
In the unlikely case that we would get a _different_ cast type, then
that's based off a route lookup and should be considered authoritative.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: extract helper to determine L2 cast type
This de-duplicates the L2 and L3 cast-type code, and makes the L2 code
a bit more robust by removing the fragile assumption that skb->data
always points to the Ethernet Header. This would break in code paths
where we pushed the HW header onto the skb.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: cache max number of available buffer elements
The QETH_MAX_BUFFER_ELEMENTS() macro effectively returns a constant
value. To avoid some redundant pointer chasing and computations in the
xmit hot path, cache this value in the queue struct.
Take this as opportunity to shrink some of the queue struct's fields to
their appropriate value range, slightly reducing its total size.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: don't clear Output buffers on every queue init
On the first initialization of a queue, its Output Buffers are in a
clean state with no attached resources. On every subsequent
initialization, qeth_l?_stop_card() has previously put them in a clean
state via qeth_drain_output_queues(). So the call to
qeth_clear_output_buffer() is redundant and can be removed.
While at it, move the initialization of the queue's card pointer into
the queue allocation. It never changes afterwards.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It's unclear what exact purpose this seqno may have served in the past.
But it's certainly no longer used anymore, as the following
napi_gro_receive() will straight away clear this part of the cb again.
Suggested-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
clang produces a harmless warning for each use for the qeth_adp_supported
macro:
drivers/s390/net/qeth_l2_main.c:559:31: warning: implicit conversion from enumeration type 'enum qeth_ipa_setadp_cmd' to
different enumeration type 'enum qeth_ipa_funcs' [-Wenum-conversion]
if (qeth_adp_supported(card, IPA_SETADP_SET_PROMISC_MODE))
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/net/qeth_core.h:179:41: note: expanded from macro 'qeth_adp_supported'
qeth_is_ipa_supported(&c->options.adp, f)
~~~~~~~~~~~~~~~~~~~~~ ^
Add a version of this macro that uses the correct types, and
remove the unused qeth_adp_enabled() macro that has the same
problem.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
cfg80211: add support to probe unexercised mesh link
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
nl80211: do a struct assignment to radar_chandef instead of memcpy()
We are copying one entire structure to another of the same type in
nl80211_notify_radar_detection, so it's simpler and safer to do a
struct assignment instead of memcpy().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Wetzel [Mon, 22 Apr 2019 21:34:11 +0000 (23:34 +0200)]
mac80211: Fix Extended Key ID auto activation
Only enable Extended Key ID support for drivers which are not supporting
crypto offload and also do not support A-MPDU.
While any driver using SW crypto from mac80211 is generally able to also
support Extended Key ID these drivers are likely to mix keyIDs in
AMPDUs when rekeying.
According to IEEE 802.11-2016 "9.7.3 A-MPDU contents" this is not
allowed.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment a bit, move ! into logic expression] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Dan Carpenter [Thu, 11 Apr 2019 08:59:50 +0000 (11:59 +0300)]
cfg80211: don't pass pointer to pointer unnecessarily
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211: store tx power value from user to station
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
cfg80211: Add support to set tx power for a station associated
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in dBm format.
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Julius Niedworok [Thu, 28 Mar 2019 20:01:06 +0000 (21:01 +0100)]
mac80211: debugfs option to force TX status frames
At Technical University of Munich we use MAC 802.11 TX status frames to
perform several measurements in MAC 802.11 setups.
With ath based drivers this was possible until commit d94a461d7a7df6
("ath9k: use ieee80211_tx_status_noskb where possible") as the driver
ignored the IEEE80211_TX_CTL_REQ_TX_STATUS flag and always delivered
tx_status frames. Since that commit, this behavior was changed and the
driver now adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
Due to performance reasons, IEEE80211_TX_CTL_REQ_TX_STATUS is not set for
data frames from interfaces in managed mode. Hence, frames that are sent
from a managed mode interface do never deliver tx_status frames. This
remains true even if a monitor mode interface (the measurement interface)
is added to the same ieee80211 physical device. Thus, there is no
possibility for receiving tx_status frames for frames sent on an interface
in managed mode, if the driver adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
In order to force delivery of tx_status frames for research and debugging
purposes, implement a debugfs option force_tx_status for ieee80211 physical
devices. When this option is set for a physical device,
IEEE80211_TX_CTL_REQ_TX_STATUS is enabled in all packets sent from that
device. This option can be set via
/sys/kernel/debug/ieee80211/<dev>/force_tx_status. The default is disabled.
Co-developed-by: Charlie Groh <ga58taw@mytum.de> Signed-off-by: Charlie Groh <ga58taw@mytum.de> Signed-off-by: Julius Niedworok <julius.n@gmx.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Colin Ian King [Wed, 27 Mar 2019 18:35:45 +0000 (18:35 +0000)]
cfg80211: remove redundant zero check on variable 'changed'
The zero check on variable changed is redundant as it must be
between 1 and 3 at the end of the proceeding if statement block.
Remove the redundant check.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211/cfg80211: update bss channel on channel switch
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
A per-group shift was added to reduce the size of the per-rate transmit
duration field to u16 without sacrificing a lot of precision
This patch changes the macros to automatically calculate the best value for
this shift based on the lowest rate within the group.
This simplifies adding more groups and slightly improves accuracy for some of
the existing groups.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Mon, 25 Mar 2019 07:59:23 +0000 (08:59 +0100)]
mac80211: when using iTXQ, select the queue in ieee80211_subif_start_xmit
When using iTXQ, the network stack does not need the real queue number, since
mac80211 is using its internal queues anyway. In that case we can defer
selecting the queue and remove a redundant station lookup in the tx path to save
some CPU cycles.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Wetzel [Tue, 19 Mar 2019 20:34:08 +0000 (21:34 +0100)]
mac80211: IEEE 802.11 Extended Key ID support
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Alexander Wetzel [Tue, 19 Mar 2019 20:34:07 +0000 (21:34 +0100)]
nl80211/cfg80211: Extended Key ID support
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Sat, 16 Mar 2019 17:06:34 +0000 (18:06 +0100)]
mac80211: set NETIF_F_LLTX when using intermediate tx queues
When using iTXQ, tx sequence number allocation and statistics are run at
dequeue time. Because of that, it is safe to enable NETIF_F_LLTX, which
allows tx handlers to run on multiple CPUs in parallel.
Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sara Sharon [Fri, 15 Mar 2019 15:39:05 +0000 (17:39 +0200)]
cfg80211: support profile split between elements
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shaul Triebitz [Fri, 15 Mar 2019 15:38:58 +0000 (17:38 +0200)]
nl80211: increase NL80211_MAX_SUPP_REG_RULES
The iwlwifi driver creates one rule per channel, thus it needs more
rules than normal. To solve this, increase NL80211_MAX_SUPP_REG_RULES
so iwlwifi can also fit UHB (ultra high band) channels.
====================
netdevsim: implement proper device model
Currently the model of netdevsim is a bit odd in multiple ways.
1) devlink instance is not in any way related with actual netdevsim
netdevices. Instead, it is created per-namespace.
2) multi-port netdevsim device is done using "link" attribute.
3) netdevsim bus is there only to have something to bind the netdev to,
it really does not act as a bus.
4) netdevsim instances are created by "ip link add" which is great for
soft devices with no hw backend. The rtnl core allocates netdev and
calls into driver holding rtnl mutex. For hw-backed devices, this
flow is wrong as it breaks order in which things are done.
This patchset adjust netdevsim to fix all above.
In order to support proper devlink and devlink port instances and to be
able to emulate real devices, there is need to implement bus probe and
instantiate everything from there. User can specify device id and port
count to be instantianted. For example:
$ echo "10 4" > /sys/bus/netdevsim/new_device
Then devlink shows this:
$ devlink dev
netdevsim/netdevsim10
$ devlink port
netdevsim/netdevsim10/0: type eth netdev eni0np1 flavour physical
netdevsim/netdevsim10/1: type eth netdev eni0np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni0np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni0np4 flavour physical
There is possible to add and delete ports using their indexes
during netdevsim device lifetime like this:
Then devlink shows this:
$ devlink port
netdevsim/netdevsim10/1: type eth netdev eni10np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni10np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni10np4 flavour physical
netdevsim/netdevsim10/43: type eth netdev eni10np44 flavour physical
Debugfs topology is also adjusted a bit. The rest stays the same as
before.
netdevsim: move netdev creation/destruction to dev probe
Remove the existing way to create netdevsim over rtnetlink and move the
netdev creation/destruction to dev probe, so for every probed port,
a netdevsim-netdev instance is created.
Adjust selftests to work with new interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: extend device attrs to support port addition and deletion
In order to test flows in core, it is beneficial to maintain previously
supported possibility to add and delete ports during netdevsim lifetime.
Do it by extending device sysfs attrs by "new_port" and "del_port".
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: implement dev probe/remove skeleton with port initialization
Implement netdevsim bus probing of netdevsim devices. For every probed
device create a devlink instance. According to the user-passed value,
create a number of ports represented by devlink port instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
With the model where dev is represented by devlink and ports are
represented by devlink ports, make debugfs file names independent
on netdev names. Change the topology to the one illustrated
by the following example:
$ ls /sys/kernel/debug/netdevsim/
netdevsim1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/
bpf_bind_accept bpf_bind_verifier_delay bpf_bound_progs ports
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/
0 1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/
bpf_map_accept bpf_offloaded_id bpf_tc_accept bpf_tc_non_bound_accept bpf_xdpdrv_accept bpf_xdpoffload_accept dev ipsec
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -l
lrwxrwxrwx 1 root root 0 Apr 13 15:58 /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -> ../../../netdevsim1
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: generate random switch id instead of using dev id
Current implementation of parent_id/switch_id does not follow the
original idea of being unique. The values are "0", "1", etc. Instead of
that, generate 32 random bytes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: add bus attributes to add new and delete devices
Add a way to add new netdevsim device on netdevsim bus and also to
delete existing netdevsim device from the bus. Track the bus devices
in using a list.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: move device registration and related code to bus.c
Move netdevsim device registration into bus.c and alongside with that
the related sysfs attributes. Introduce new struct nsim_bus_dev to
represent a netdevsim device on netdevsim bus.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: rename devlink.c to dev.c to contain per-dev(asic) items
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: create devlink instance per netdevsim instance
Currently there is one devlink instance created per network namespace.
That is quite odd considering the fact that devlink instance should
represent an ASIC. The following patches are going to move the devlink
instance even more down to a bus device, but until then, have one
devlink instance per netdevsim instance. Struct nsim_devlink is
introduced to hold fib setting.
The changes in the fib code are only related to holding the
configuration per devlink instance instead of network namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: Align minimum encryption key size for LE and BR/EDR connections
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
Merge tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Eric Dumazet [Wed, 24 Apr 2019 15:04:05 +0000 (08:04 -0700)]
ipv4: add sanity checks in ipv4_link_failure()
Before calling __ip_options_compile(), we need to ensure the network
header is a an IPv4 one, and that it is already pulled in skb->head.
RAW sockets going through a tunnel can end up calling ipv4_link_failure()
with total garbage in the skb, or arbitrary lengthes.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:355 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
Write of size 69 at addr ffff888096abf068 by task syz-executor.4/9204
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Apr 2019 16:44:11 +0000 (09:44 -0700)]
rxrpc: fix race condition in rxrpc_input_packet()
After commit 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook"),
rxrpc_input_packet() is directly called from lockless UDP receive
path, under rcu_read_lock() protection.
It must therefore use RCU rules :
- udp_sk->sk_user_data can be cleared at any point in this function.
rcu_dereference_sk_user_data() is what we need here.
- Also, since sk_user_data might have been set in rxrpc_open_socket()
we must observe a proper RCU grace period before kfree(local) in
rxrpc_lookup_local()
v4: @local can be NULL in xrpc_lookup_local() as reported by kbuild test robot <lkp@intel.com>
and Julia Lawall <julia.lawall@lip6.fr>, thanks !
v3,v2 : addressed David Howells feedback, thanks !
Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before the commit 490ea5967b0d ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit 490ea5967b0d ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M
The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us
cpu %
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.
Fixes: commit 490ea5967b0d ("RDS: IB: move FMR code to its own file") Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: flower: refactor reoffload for concurrent access
Recent changes that introduced unlocked flower did not properly account for
case when reoffload is initiated concurrently with filter updates. To fix
the issue, extend flower with 'hw_filters' list that is used to store
filters that don't have 'skip_hw' flag set. Filter is added to the list
when it is inserted to hardware and only removed from it after being
unoffloaded from all drivers that parent block is attached to. This ensures
that concurrent reoffload can still access filter that is being deleted and
prevents race condition when driver callback can be removed when filter is
no longer accessible trough idr, but is still present in hardware.
Refactor fl_change() to respect new filter reference counter and to release
filter reference with __fl_put() in case of error, instead of directly
deallocating filter memory. This allows for concurrent access to filter
from fl_reoffload() and protects it with reference counting. Refactor
fl_reoffload() to iterate over hw_filters list instead of idr. Implement
fl_get_next_hw_filter() helper function that is used to iterate over
hw_filters list with reference counting and skips filters that are being
concurrently deleted.
Fixes: 92149190067d ("net: sched: flower: set unlocked flag for flower proto ops") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 16:24:46 +0000 (09:24 -0700)]
tipc: tipc_udp_recv() cleanup vs rcu verbs
First thing tipc_udp_recv() does is to use rcu_dereference_sk_user_data(),
and this is really hinting we already own rcu_read_lock() from the caller
(UDP stack).
No need to add another rcu_read_lock()/rcu_read_unlock() pair.
Also use rcu_dereference() instead of rcu_dereference_rtnl()
in the data path.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: hci_core: Don't stop BT if the BD address missing in dts
When flag HCI_QUIRK_USE_BDADDR_PROPERTY is set, we will read the
bluetooth address from dts. If the bluetooth address node is missing
from the dts we will enable it controller UNCONFIGURED state.
This patch enables the normal flow even if the BD address is missing
from the dts tree.
David Ahern [Wed, 24 Apr 2019 01:05:33 +0000 (18:05 -0700)]
ipv6: Use result arg in fib_lookup_arg consistently
arg.result is sometimes used as fib6_result and sometimes used to
hold the rt6_info. Add rt6_info to fib6_result and make the use
of arg.result consistent through ipv6 rules.
The rt6 entry is filled in for lookups returning a dst_entry, but not
for direct fib_lookups that just want a fib6_info.
Fixes: effda4dd97e8 ("ipv6: Pass fib6_result to fib lookups") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log