Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
mmc: sdhci: Drop redundant check in sdhci_ack_sdio_irq()
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
mmc: core: Fixup processing of SDIO IRQs during system suspend/resume
System suspend/resume of SDIO cards, with SDIO IRQs enabled and when using
MMC_CAP2_SDIO_IRQ_NOTHREAD is unfortunate still suffering from a fragile
behaviour. Some problems have been taken care of so far, but more issues
remains.
For example, calling the ->ack_sdio_irq() callback to let host drivers
re-enable the SDIO IRQs is a bad idea, unless the IRQ have been consumed,
which may not be the case during system suspend/resume. This may lead to
that a host driver re-signals the same SDIO IRQ over and over again,
causing a storm of IRQs and gives a ping-pong effect towards the
sdio_irq_work().
Moreover, calling the ->enable_sdio_irq() callback at system resume to
re-enable already enabled SDIO IRQs for the host, causes the runtime PM
count for some host drivers to become in-balanced. This then leads to the
host to remain runtime resumed, no matter if it's needed or not.
To fix these problems, let's check if process_sdio_pending_irqs() actually
consumed the SDIO IRQ, before we continue to ack the IRQ by invoking the
->ack_sdio_irq() callback.
Additionally, there should be no need to re-enable SDIO IRQs as the host
driver already knows if they were enabled at system suspend, thus also
whether it needs to re-enable them at system resume. For this reason, drop
the call to ->enable_sdio_irq() during system resume.
In regards to these changes there is yet another issue, which is when there
is an SDIO IRQ being signaled by the host driver, but after the SDIO card
has been system suspended. Currently these IRQs are just thrown away, while
we should at least make sure to try to consume them when the SDIO card has
been system resumed. Fix this by queueing a sdio_irq_work() after we system
resumed the SDIO card.
Tested-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: core: WARN if SDIO IRQs are enabled for non-powered card in suspend
To make sure SDIO func drivers behaves correctly during system
suspend/resume, let add a WARN_ON in case the condition is a non-powered
SDIO card and there are some SDIO IRQs still being claimed.
mmc: core: Clarify that the ->ack_sdio_irq() callback is mandatory
For the MMC_CAP2_SDIO_IRQ_NOTHREAD case and when using sdio_signal_irq(),
the ->ack_sdio_irq() is already mandatory, which was not the case for those
host drivers that called sdio_run_irqs() directly.
As there are no longer any drivers calling sdio_run_irqs(), let's clarify
the code by dropping the unnecessary check and explicitly state that the
callback is mandatory in the header file.
Tested-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: core: Clarify sdio_irq_pending flag for MMC_CAP2_SDIO_IRQ_NOTHREAD
The sdio_irq_pending flag is used to let host drivers indicate that it has
signaled an IRQ. If that is the case and we only have a single SDIO func
that have claimed an SDIO IRQ, our assumption is that we can avoid reading
the SDIO_CCCR_INTx register and just call the SDIO func irq handler
immediately. This makes sense, but the flag is set/cleared in a somewhat
messy order, let's fix that up according to below.
First, the flag is currently set in sdio_run_irqs(), which is executed as a
work that was scheduled from sdio_signal_irq(). To make it more implicit
that the host have signaled an IRQ, let's instead immediately set the flag
in sdio_signal_irq(). This also makes the behavior consistent with host
drivers that uses the legacy, mmc_signal_sdio_irq() API. This have no
functional impact, because we don't expect host drivers to call
sdio_signal_irq() until after the work (sdio_run_irqs()) have been executed
anyways.
Second, currently we never clears the flag when using the sdio_run_irqs()
work, but only when using the sdio_irq_thread(). Let make the behavior
consistent, by moving the flag to be cleared inside the common
process_sdio_pending_irqs() function. Additionally, tweak the behavior of
the flag slightly, by avoiding to clear it unless we processed the SDIO
IRQ. The purpose with this at this point, is to keep the information about
whether there have been an SDIO IRQ signaled by the host, so at system
resume we can decide to process it without reading the SDIO_CCCR_INTx
register.
Tested-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: mtk-sd: Re-store SDIO IRQs mask at system resume
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
mmc: dw_mmc: Re-store SDIO IRQs mask at system resume
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means dw_mci_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the dw_mmc
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the dw_mmc driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the dw_mmc driver, so let's do that.
Tested-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: core: Add helper function to indicate if SDIO IRQs is enabled
To avoid each host driver supporting SDIO IRQs, from keeping track
internally about if SDIO IRQs has been claimed, let's introduce a common
helper function, sdio_irq_claimed().
The function returns true if SDIO IRQs are claimed, via using the
information about the number of claimed irqs. This is safe, even without
any locks, as long as the helper function is called only from
runtime/system suspend callbacks of the host driver.
Tested-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Al Cooper [Tue, 3 Sep 2019 11:51:14 +0000 (07:51 -0400)]
mmc: sdhci: Fix incorrect switch to HS mode
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Al Cooper <alcooperx@gmail.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SPARC does not set CONFIG_OF_ADDRESS so the symbol is missing. Depend on
CONFIG_OF_ADDRESS to ensure the driver is only built for supported
configurations.
Fixes: 2d28dbe042f4 ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Jeffery [Mon, 2 Sep 2019 03:58:42 +0000 (13:28 +0930)]
mmc: sdhci-of-aspeed: Allow max-frequency limitation of SDCLK
Add a get_max_clock() handler to sdhci-of-aspeed to report f_max as the
maximum clock rate if it is set. This enables artificial limitation of
the bus speed via max-frequency in the devicetree for e.g. the AST2600
evaluation board where I was seeing errors at 200MHz.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Jeffery [Mon, 2 Sep 2019 03:58:41 +0000 (13:28 +0930)]
mmc: sdhci-of-aspeed: Uphold clocks-on post-condition of set_clock()
The early-exit didn't seem to matter on the AST2500, but on the AST2600
the SD clock genuinely may not be running on entry to
aspeed_sdhci_set_clock(). Remove the early exit to ensure we always run
sdhci_enable_clk().
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tamás Szűcs [Thu, 29 Aug 2019 18:36:34 +0000 (20:36 +0200)]
mmc: sdhi: fill in actual_clock
Save set clock in mmc_host actual_clock enabling exporting it via debugfs.
This will indicate the precise SD clock in I/O settings rather than only the
sometimes misleading requested clock.
Masahiro Yamada [Thu, 29 Aug 2019 10:49:28 +0000 (19:49 +0900)]
mmc: sdhci-cadence: override spec version
The datasheet of the IP (sd4hc) says it is compiatible with SDHCI v4,
but the spec version field in the version register is read as 2
(i.e. SDHCI_SPEC_300) based on the RTL provided by Cadence.
Socionext did not fix it up when it integrated the IP into the SoCs.
So, it is working as SDHCI v3.
It is not a real problem because there is no difference in the program
flow in sdhci.c between SDHCI_SPEC_300/400, but set the real version
just in case.
yong mao [Wed, 28 Aug 2019 09:45:24 +0000 (17:45 +0800)]
mmc: mediatek: enable SDIO IRQ low level trigger function
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Ben Chuang [Tue, 27 Aug 2019 00:33:22 +0000 (08:33 +0800)]
mmc: sdhci: Export sdhci_abort_tuning function symbol
Export sdhci_abort_tuning() function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Co-developed-by: Michael K Johnson <johnsonm@danlj.org> Signed-off-by: Michael K Johnson <johnsonm@danlj.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Chuang [Tue, 27 Aug 2019 00:33:09 +0000 (08:33 +0800)]
PCI: Add Genesys Logic, Inc. Vendor ID
Add the Genesys Logic, Inc. vendor ID to pci_ids.h.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Co-developed-by: Michael K Johnson <johnsonm@danlj.org> Signed-off-by: Michael K Johnson <johnsonm@danlj.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Chuang [Tue, 27 Aug 2019 00:32:55 +0000 (08:32 +0800)]
mmc: sdhci: Add PLL Enable support to internal clock setup
The GL9750 and GL9755 chipsets, and possibly others, require PLL Enable
setup as part of the internal clock setup as described in 3.2.1 Internal
Clock Setup Sequence of SD Host Controller Simplified Specification
Version 4.20.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Co-developed-by: Michael K Johnson <johnsonm@danlj.org> Signed-off-by: Michael K Johnson <johnsonm@danlj.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Chuang [Tue, 27 Aug 2019 00:32:42 +0000 (08:32 +0800)]
mmc: sdhci: Change timeout of loop for checking internal clock stable
According to section 3.2.1 internal clock setup in SD Host Controller
Simplified Specifications 4.20, the timeout of loop for checking
internal clock stable is defined as 150ms.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw> Co-developed-by: Michael K Johnson <johnsonm@danlj.org> Signed-off-by: Michael K Johnson <johnsonm@danlj.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wei Yongjun [Mon, 26 Aug 2019 12:00:13 +0000 (12:00 +0000)]
mmc: sdhci-of-aspeed: Fix return value check in aspeed_sdc_probe()
In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Andrew Jeffery [Mon, 26 Aug 2019 02:16:19 +0000 (11:46 +0930)]
dt-bindings: mmc: sdhci-of-aspeed: Update example ranges property
The example node in the binding uses the AST2500 compatible string for
the SD controller with a 64kiB ranges property, but the SD controller is
allocated 128kiB of MMIO space according to the AST2500 datasheet. Fix
the example to correctly reflect the hardware in the AST2500, however it
should be noted that the MMIO region is reduced to 64kiB in the AST2600
where a second SD controller block has been introduced into the address
space.
Also add the IBM copyright header that I left out of the initial patch.
Suggested-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andrew Jeffery [Wed, 7 Aug 2019 00:36:29 +0000 (10:06 +0930)]
mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.
The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).
The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.
Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.
Signed-off-by: Ryan Chen <ryanchen.aspeed@gmail.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ASPEED SD/SDIO/MMC controller exposes two slots implementing the
SDIO Host Specification v2.00, with 1 or 4 bit data buses, or an 8 bit
data bus if only a single slot is enabled.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Chaotian Jing [Thu, 22 Aug 2019 06:47:40 +0000 (14:47 +0800)]
mmc: mediatek: fix controller busy when plug out SD
when plug out SD card, may get data CRC error, the MMC core will issue
CMD13 to get card status, then CMD13 timeout(due to card plug out) will
trigger CMD19 tuning, first CMD19 timeout has not call msdc_reset_hw()
and cause the next CMD19 gets controller busy.
mmc: renesas_sdhi_sys_dmac: Remove all R-Car Gen3 SoCs
All R-Car Gen3 SoCs with any ES version cannot use this DMAC actually.
So, this patch removes the compatibles of R-Car Gen3 SoCs from
renesas_sdhi_sys_dmac_of_match. Since the previous code has
an empty whitelist to prevent probing of R-Car Gen3 SoCs,
no behavior changes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Also, notice that, in this case, variable priv_size is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stephen Boyd [Tue, 30 Jul 2019 18:15:29 +0000 (11:15 -0700)]
mmc: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/sdhci-s3c.c: In function 'sdhci_s3c_probe':
drivers/mmc/host/sdhci-s3c.c:613:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->mmc->caps |= MMC_CAP_8_BIT_DATA;
drivers/mmc/host/sdhci-s3c.c:614:2: note: here
case 4:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: atmel-mci: Mark expected switch fall-throughs
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/atmel-mci.c: In function 'atmci_get_cap':
drivers/mmc/host/atmel-mci.c:2415:30: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_odd_clk_div = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2416:2: note: here
case 0x400:
^~~~
drivers/mmc/host/atmel-mci.c:2422:28: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_highspeed = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2423:2: note: here
case 0x200:
^~~~
drivers/mmc/host/atmel-mci.c:2426:40: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.need_notbusy_for_read_ops = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2427:2: note: here
case 0x100:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc: sdhci-pltfm: Use devm_platform_ioremap_resource() to simplify code
devm_platform_ioremap_resource() wraps platform_get_resource() and
devm_ioremap_resource() in a single helper, let's use that helper to
simplify the code.
mmc: mmci: Clarify comments and some code for busy detection
The code dealing with busy detection is somewhat complicated. In a way to
make it a bit clearer, let's try to clarify the comments in the code about
it.
Additionally, move the part for clearing the so called busy start IRQ, to
the place where the IRQ is actually delivered. Ideally, this should make
the code a bit more robust.
Finally, to improve understanding of the code and the sequence of the busy
detection, move the corresponding code around a bit in mmci_cmd_irq().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com> Reviewed-by: Jean Nicolas GRAUX <jean-nicolas.graux@st.com>
Stefan Wahren [Mon, 22 Jul 2019 06:23:23 +0000 (08:23 +0200)]
mmc: sdhci-iproc: Add support for emmc2 of the BCM2711
The additional emmc2 interface of the BCM2711 is an improved version
of the old emmc controller, which is able to provide DDR50 mode on the
Raspberry Pi 4. Except 32 bit only register access no other quirks are
known yet.
mmc: mxs: use devm_platform_ioremap_resource() to simplify code
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Lars Persson [Tue, 9 Jul 2019 13:53:51 +0000 (15:53 +0200)]
mmc: usdhi6rol0: Add maintainers
The usdhi6rol0 driver is exclusively used for the ARTPEC family of
SoCs. Other SoCs with the same IP of Panasonic origin use the tmio_mmc
driver. Therefore we assigner maintainer responsibility to us at Axis
until the two drivers become unified.
Signed-off-by: Lars Persson <larper@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit broke eMMC storage access on a new consumer MiniPC based on
AMD SoC, which has eMMC connected to:
02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01)
Subsystem: O2 Micro, Inc. Device 0002
During probe, several errors are seen including:
mmc1: Got data interrupt 0x02000000 even though no data operation was in progress.
mmc1: Timeout waiting for hardware interrupt.
mmc1: error -110 whilst initialising MMC card
Reverting this commit allows the eMMC storage to be detected & usable
again.
Signed-off-by: Daniel Drake <drake@endlessm.com> Fixes: 414126f9e5ab ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host
controller") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Stefan Wahren [Sun, 8 Sep 2019 07:45:52 +0000 (09:45 +0200)]
Revert "mmc: bcm2835: Terminate timeout work synchronously"
The commit 37fefadee8bb ("mmc: bcm2835: Terminate timeout work
synchronously") causes lockups in case of hardware timeouts due the
timeout work also calling cancel_delayed_work_sync() on its own.
So revert it.
Fixes: 37fefadee8bb ("mmc: bcm2835: Terminate timeout work synchronously") Cc: stable@vger.kernel.org Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge tag 'gpio-v5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"All related to the PCA953x driver when handling chips with more than 8
ports, now that works again"
* tag 'gpio-v5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: use pca953x_read_regs instead of regmap_bulk_read
gpio: pca953x: correct type of reg_direction
Nick Desaulniers [Wed, 28 Aug 2019 22:55:23 +0000 (15:55 -0700)]
include/linux/compiler.h: fix Oops for Clang-compiled kernels
GCC unescapes escaped string section names while Clang does not. Because
__section uses the `#` stringification operator for the section name, it
doesn't need to be escaped.
This fixes an Oops observed in distro's that use systemd and not
net.core.bpf_jit_enable=1, when their kernels are compiled with Clang.
Chris Wilson reports that it breaks his CPU hotplug test scripts. In
particular, it breaks offlining and then re-onlining the boot CPU, which
we treat specially (and the BIOS does too).
The symptoms are that we can offline the CPU, but it then does not come
back online again:
smpboot: CPU 0 is now offline
smpboot: Booting Node 0 Processor 0 APIC 0x0
smpboot: do_boot_cpu failed(-1) to wakeup CPU#0
Thomas says he knows why it's broken (my personal suspicion: our magic
handling of the "cpu0_logical_apicid" thing), but for 5.3 the right fix
is to just revert it, since we've never touched the LDR bits before, and
it's not worth the risk to do anything else at this stage.
[ Hotpluging of the boot CPU is special anyway, and should be off by
default. See the "BOOTPARAM_HOTPLUG_CPU0" config option and the
cpu0_hotplug kernel parameter.
In general you should not do it, and it has various known limitations
(hibernate and suspend require the boot CPU, for example).
But it should work, even if the boot CPU is special and needs careful
treatment - Linus ]
Merge tag 'char-misc-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation updates from Greg KH:
"A few small patches for the documenation file that came in through the
char-misc tree in -rc7 for your tree.
They fix the mistake in the .rst format that kept the table of
companies from showing up in the html output, and most importantly,
add people's names to the list showing support for our process"
* tag 'char-misc-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Add Qualcomm process ambassador for hardware security issues
Documentation/process/embargoed-hardware-issues: Microsoft ambassador
Documentation/process: Add Google contact for embargoed hardware issues
Documentation/process: Volunteer as the ambassador for Xen
Merge tag 'libnvdimm-fix-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"Restore support for 1GB alignment namespaces, truncate the end of
misaligned namespaces"
* tag 'libnvdimm-fix-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/pfn: Fix namespace creation on misaligned addresses
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A tiny update from Benjamin removing a mistakenly added Elan PNP ID so
that the device is again handled by hid-multitouch"
Merge tag 'configfs-for-5.3' of git://git.infradead.org/users/hch/configfs
Pull configfs fixes from Christoph Hellwig:
"Late configfs fixes from Al that fix pretty nasty removal vs attribute
access races"
* tag 'configfs-for-5.3' of git://git.infradead.org/users/hch/configfs:
configfs: provide exclusion between IO and removals
configfs: new object reprsenting tree fragments
configfs_register_group() shouldn't be (and isn't) called in rmdirable parts
configfs: stash the data we need into configfs_buffer at open time
Merge tag 'iommu-fixes-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Revert an Intel VT-d patch that caused problems for some users.
- Removal of a feature in the Intel VT-d driver that was never
supported in hardware. This qualifies as a fix because the code for
this feature sets reserved bits in the invalidation queue descriptor,
causing failed invalidations on real hardware.
- Two fixes for AMD IOMMU driver to fix a race condition and to add a
missing IOTLB flush when kernel is booted in kdump mode.
* tag 'iommu-fixes-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix race in increase_address_space()
iommu/amd: Flush old domains in kdump kernel
iommu/vt-d: Remove global page flush support
Revert "iommu/vt-d: Avoid duplicated pci dma alias consideration"
Merge tag 'drm-fixes-2019-09-06' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Live from my friend's couch in Barcelona, latest round of drm fixes.
The command line parser regression fixes look a bit larger because
they come with selftests included for the bugs they fix. Otherwise a
single nouveau, single ingenic and single vmwgfx fix:
* tag 'drm-fixes-2019-09-06' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Fix double free in vmw_recv_msg()
drm/nouveau/sec2/gp102: add missing MODULE_FIRMWAREs
drm/selftests: modes: Add more unit tests for the cmdline parser
drm/modes: Introduce a whitelist for the named modes
drm/modes: Fix the command line parser to take force options into account
drm/modes: Add a switch to differentiate free standing options
drm/ingenic: Hardcode panel type to DPI
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"virtio, vhost, and balloon bugfixes.
A couple of last minute bugfixes. And a revert of a failed attempt at
metadata access optimization - we'll try again in the next cycle"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
mm/balloon_compaction: suppress allocation warnings
Revert "vhost: access vq metadata through kernel virtual address"
vhost: Remove unnecessary variable
virtio-net: lower min ring num_free for efficiency
vhost/test: fix build for vhost test
vhost/test: fix build for vhost test
Merge tag 'powerpc-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a boot hang on some Freescale machines when PREEMPT is
enabled.
Two CVE fixes for bugs in our handling of FP registers and
transactional memory, both of which can result in corrupted FP state,
or FP state leaking between processes.
Thanks to: Chris Packham, Christophe Leroy, Gustavo Romero, Michael
Neuling"
* tag 'powerpc-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Fix FP/VMX unavailable exceptions inside a transaction
powerpc/64e: Drop stale call to smp_processor_id() which hangs SMP startup
Lee Jones [Thu, 5 Sep 2019 08:25:55 +0000 (09:25 +0100)]
soc: qcom: geni: Provide parameter error checking
When booting with ACPI, the Geni Serial Engine is not set as the I2C/SPI
parent and thus, the wrapper (parent device) is unassigned. This causes
the kernel to crash with a null dereference error.
Link: https://lore.kernel.org/r/20190905082555.15020-1-lee.jones@linaro.org Fixes: 8bc529b25354 ("soc: qcom: geni: Add support for ACPI") Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After the conversion to lock-less dma-api call the
increase_address_space() function can be called without any
locking. Multiple CPUs could potentially race for increasing
the address space, leading to invalid domain->mode settings
and invalid page-tables. This has been happening in the wild
under high IO load and memory pressure.
Fix the race by locking this operation. The function is
called infrequently so that this does not introduce
a performance regression in the dma-api path again.
Reported-by: Qian Cai <cai@lca.pw> Fixes: 256e4621c21a ('iommu/amd: Make use of the generic IOVA allocator') Signed-off-by: Joerg Roedel <jroedel@suse.de>
Stuart Hayes [Thu, 5 Sep 2019 17:09:48 +0000 (12:09 -0500)]
iommu/amd: Flush old domains in kdump kernel
When devices are attached to the amd_iommu in a kdump kernel, the old device
table entries (DTEs), which were copied from the crashed kernel, will be
overwritten with a new domain number. When the new DTE is written, the IOMMU
is told to flush the DTE from its internal cache--but it is not told to flush
the translation cache entries for the old domain number.
Without this patch, AMD systems using the tg3 network driver fail when kdump
tries to save the vmcore to a network system, showing network timeouts and
(sometimes) IOMMU errors in the kernel log.
This patch will flush IOMMU translation cache entries for the old domain when
a DTE gets overwritten with a new domain number.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com> Fixes: 3ac3e5ee5ed5 ('iommu/amd: Copy old trans table from old kernel') Signed-off-by: Joerg Roedel <jroedel@suse.de>
keys: Fix missing null pointer check in request_key_auth_describe()
If a request_key authentication token key gets revoked, there's a window in
which request_key_auth_describe() can see it with a NULL payload - but it
makes no check for this and something like the following oops may occur:
Fix this by checking for a NULL pointer when describing such a key.
Also make the read routine check for a NULL pointer to be on the safe side.
[DH: Modified to not take already-held rcu lock and modified to also check
in the read routine]
Fixes: 04c567d9313e ("[PATCH] Keys: Fix race between two instantiators of a key") Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'sound-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small HD-audio fixes:
- A regression fix for Realtek codecs due to the recent
initialization procedure change
- A fix for potential endless loop at the quirk table lookup
- Quirks for Lenovo, ASUS and HP machines"
* tag 'sound-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix the problem of two front mics on a ThinkCentre
ALSA: hda/realtek - Enable internal speaker & headset mic of ASUS UX431FL
ALSA: hda/realtek - Add quirk for HP Pavilion 15
ALSA: hda/realtek - Fix overridden device-specific initialization
ALSA: hda - Fix potential endless loop at applying quirks
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- EFI boot fix for signed kernels
- an AC flags fix related to UBSAN
- Hyper-V infinite loop fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hyper-v: Fix overflow bug in fill_gva_list()
x86/uaccess: Don't leak the AC flags into __get_user() argument evaluation
x86/boot: Preserve boot_params.secure_boot from sanitizing
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"This fixes an ABI bug introduced this cycle, plus fixes a throttling
bug"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix uclamp ABI bug, clean up and robustify sched_read_attr() ABI logic and code
sched/fair: Don't assign runtime for throttled cfs_rq
Dan Carpenter [Thu, 15 Aug 2019 08:30:50 +0000 (11:30 +0300)]
drm/vmwgfx: Fix double free in vmw_recv_msg()
We recently added a kfree() after the end of the loop:
if (retries == RETRIES) {
kfree(reply);
return -EINVAL;
}
There are two problems. First the test is wrong and because retries
equals RETRIES if we succeed on the last iteration through the loop.
Second if we fail on the last iteration through the loop then the kfree
is a double free.
When you're reading this code, please note the break statement at the
end of the while loop. This patch changes the loop so that if it's not
successful then "reply" is NULL and we can test for that afterward.
Cc: <stable@vger.kernel.org> Fixes: 6b7c3b86f0b6 ("drm/vmwgfx: fix memory leak when too many retries have occurred") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Al Viro [Sat, 31 Aug 2019 07:43:43 +0000 (09:43 +0200)]
configfs: provide exclusion between IO and removals
Make sure that attribute methods are not called after the item
has been removed from the tree. To do so, we
* at the point of no return in removals, grab ->frag_sem
exclusive and mark the fragment dead.
* call the methods of attributes with ->frag_sem taken
shared and only after having verified that the fragment is still
alive.
The main benefit is for method instances - they are
guaranteed that the objects they are accessing *and* all ancestors
are still there. Another win is that we don't need to bother
with extra refcount on config_item when opening a file -
the item will be alive for as long as it stays in the tree, and
we won't touch it/attributes/any associated data after it's
been removed from the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Christoph Hellwig <hch@lst.de>
sched/core: Fix uclamp ABI bug, clean up and robustify sched_read_attr() ABI logic and code
Thadeu Lima de Souza Cascardo reported that 'chrt' broke on recent kernels:
$ chrt -p $$
chrt: failed to get pid 26306's policy: Argument list too long
and he has root-caused the bug to the following commit increasing sched_attr
size and breaking sched_read_attr() into returning -EFBIG:
a509a7cd7974 ("sched/uclamp: Extend sched_setattr() to support utilization clamping")
The other, bigger bug is that the whole sched_getattr() and sched_read_attr()
logic of checking non-zero bits in new ABI components is arguably broken,
and pretty much any extension of the ABI will spuriously break the ABI.
That's way too fragile.
Instead implement the perf syscall's extensible ABI instead, which we
already implement on the sched_setattr() side:
- if user-attributes have the same size as kernel attributes then the
logic is unchanged.
- if user-attributes are larger than the kernel knows about then simply
skip the extra bits, but set attr->size to the (smaller) kernel size
so that tooling can (in principle) handle older kernel as well.
- if user-attributes are smaller than the kernel knows about then just
copy whatever user-space can accept.
Also clean up the whole logic:
- Simplify the code flow - there's no need for 'ret' for example.
- Standardize on 'kattr/uattr' and 'ksize/usize' naming to make sure we
always know which side we are dealing with.
- Why is it called 'read' when what it does is to copy to user? This
code is so far away from VFS read() semantics that the naming is
actively confusing. Name it sched_attr_copy_to_user() instead, which
mirrors other copy_to_user() functionality.
- Move the attr->size assignment from the head of sched_getattr() to the
sched_attr_copy_to_user() function. Nothing else within the kernel
should care about the size of the structure.
With these fixes the sched_getattr() syscall now nicely supports an
extensible ABI in both a forward and backward compatible fashion, and
will also fix the chrt bug.
As an added bonus the bogus -EFBIG return is removed as well, which as
Thadeu noted should have been -E2BIG to begin with.
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Tested-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Cc: Arnaldo Carvalho de Melo <acme@infradead.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Patrick Bellasi <patrick.bellasi@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: a509a7cd7974 ("sched/uclamp: Extend sched_setattr() to support utilization clamping") Link: https://lkml.kernel.org/r/20190904075532.GA26751@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'renesas-fixes-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Renesas ARM Based SoC Fixes for v5.3
* R-Car D3 (r8a77995) based Draak Board
- Correct backlight regulator name in device tree
* tag 'renesas-fixes-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77995: draak: Fix backlight regulator name