Linus Walleij [Thu, 22 Mar 2018 10:22:24 +0000 (11:22 +0100)]
usb: phy: ab8500: Drop AB8540/9540 support
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Hans de Goede [Tue, 20 Mar 2018 12:57:13 +0000 (15:57 +0300)]
extcon: axp288: Set USB role where necessary
The AXP288 BC1.2 charger detection / extcon code may seem like a strange
place to add code to control the USB role-switch on devices with an AXP288,
but there are 2 reasons to do this inside the axp288 extcon code:
1) On many devices the USB role is controlled by ACPI AML code, but the AML
code only switches between the host and none roles, because of Windows
not really using device mode. To make device mode work we need to toggle
between the none/device roles based on Vbus presence, and the axp288
extcon gets interrupts on Vbus insertion / removal.
2) In order for our BC1.2 charger detection to work properly the role
mux must be properly set to device mode before we do the detection.
Also note the Kconfig help-text / obsolete depends on USB_PHY which are
remnants from older never upstreamed code also controlling the mux from
the axp288 extcon code.
This commit also adds code to get notifications from the INT3496 extcon
device, which is used on some devices to notify the kernel about id-pin
changes instead of them being handled through AML code.
This fixes:
-Device mode not working on most CHT devices with an AXP288
-Host mode not working on devices with an INT3496 ACPI device
-Charger-type misdetection (always SDP) on devices with an INT3496 when the
USB role (always) gets initialized as host
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:12 +0000 (15:57 +0300)]
platform/x86: intel_cht_int33fe: Add device connections for the Type-C port
We need to add device-connections for the Type-C mux/switch and usb-role
code to be able to find the PI3USB30532 Type-C cross-switch and the
device/host role-switch integrated in the CHT SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:11 +0000 (15:57 +0300)]
usb: typec: driver for Pericom PI3USB30532 Type-C cross switch
Add a driver for the Pericom PI3USB30532 Type-C cross switch /
mux chip found on some devices with a Type-C port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:10 +0000 (15:57 +0300)]
usb: roles: Add Intel xHCI USB role switch driver
Various Intel SoCs (Cherry Trail, Broxton and others) have an internal USB
role switch for swiching the OTG USB data lines between the xHCI host
controller and the dwc3 gadget controller.
Note on some Cherry Trail systems there is ACPI/AML code listening to
edge interrupts on the id-pin (through an _AIE ACPI method) and switching
the role between ROLE_HOST and ROLE_NONE based on the id-pin. Note it does
not set the role to ROLE_DEVICE, because device-mode is usually not used
under Windows.
The presence of AML code which modifies the cfg0 reg (on some systems)
means that our read/write/modify of cfg0 may race with the AML code
doing the same to avoid this we take the global ACPI lock while doing
the read/write/modify.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:09 +0000 (15:57 +0300)]
xhci: Add Intel extended cap / otg phy mux handling
The xHCI controller on various Intel SoCs has an extended cap mmio-range
which contains registers to control the muxing to the xHCI (host mode)
or the dwc3 (device mode) and vbus-detection for the otg usb-phy.
Having a role-sw driver included in the xHCI code (under drivers/usb/host)
is not desirable. So this commit adds a simple handler for this extended
capability, which creates a platform device with the caps mmio region as
resource, this allows us to write a separate platform role-sw driver for
the role-switch.
Note this commit adds a call to the new xhci_ext_cap_init() function
to xhci_pci_probe(), it is added here because xhci_ext_cap_init() must
be called only once. If in the future we also want to handle ext-caps
on non pci xHCI HCDs from xhci_ext_cap_init() a call to it should also
be added to other bus probe paths.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Tue, 20 Mar 2018 12:57:08 +0000 (15:57 +0300)]
xhci: Add option to get next extended capability in list by passing id = 0
Modify xhci_find_next_ext_cap(base, offset, id) to return the next
capability offset if 0 is passed for id. Otherwise it will behave as
previously and return the offset of the next capability with matching id
capability id 0 is not used by xHCI (reserved)
This is useful when we want to loop through all capabilities.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:07 +0000 (15:57 +0300)]
usb: typec: tcpm: Use new Type-C switch/mux and usb-role-switch functions
Remove the unused (not implemented anywhere) tcpc_mux_dev abstraction
and replace it with calling the new typec_set_orientation,
usb_role_switch_set and typec_set_mode functions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 20 Mar 2018 12:57:06 +0000 (15:57 +0300)]
usb: typec: tcpm: Set USB role switch to device mode when configured as such
Setting the mux to MUX_NONE and the switch to USB_SWITCH_DISCONNECT when
the data-role is device is not correct. Plenty of devices support
operating as USB device through a (separate) USB device controller.
We really need 2 different versions of USB_SWITCH_CONNECT,
USB_SWITCH_CONNECT_HOST and USB_SWITCH_DEVICE. Rather then modifying the
tcpc_usb_switch enum for this, simply remove it and switch to the
usb_role enum which provides exactly this, this will save use needing to
convert betweent the 2 enums when calling an usb-role-switch driver later.
Besides switching to the usb_role type, this commit also actually sets the
mux to TYPEC_MUX_USB and the switch to USB_ROLE_DEVICE instead of setting
both to none when the data-role is device.
This commit also makes tcpm_reset_port() call tcpm_mux_set(port,
TYPEC_MUX_NONE, USB_ROLE_NONE) so that the mux and switch
do _not_ stay in their last mode after a detach.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Tue, 20 Mar 2018 12:57:05 +0000 (15:57 +0300)]
usb: typec: Separate the definitions for data and power roles
USB Type-C specification v1.2 separated the power and data
roles more clearly. Dual-Role-Data term was introduced, and
the meaning of DRP was changed from "Dual-Role-Port" to
"Dual-Role-Power".
In order to allow the port drivers to describe the
capabilities of the ports more clearly according to the
newest specifications, introducing separate definitions for
the data roles.
Heikki Krogerus [Tue, 20 Mar 2018 12:57:04 +0000 (15:57 +0300)]
usb: common: Small class for USB role switches
USB role switch is a device that can be used to choose the
data role for USB connector. With dual-role capable USB
controllers, the controller itself will be the switch, but
on some platforms the USB host and device controllers are
separate IPs and there is a mux between them and the
connector. On those platforms the mux driver will need to
register the switch.
With USB Type-C connectors, the host-to-device relationship
is negotiated over the Configuration Channel (CC). That
means the USB Type-C drivers need to be in control of the
role switch. The class provides a simple API for the USB
Type-C drivers for the control.
For other types of USB connectors (mainly microAB) the class
provides user space control via sysfs attribute file that
can be used to request role swapping from the switch.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Tue, 20 Mar 2018 12:57:03 +0000 (15:57 +0300)]
usb: typec: API for controlling USB Type-C Multiplexers
USB Type-C connectors consist of various muxes and switches
that route the pins on the connector to the right locations.
The USB Type-C drivers need to be able to control the muxes,
as they are the ones that know things like the cable plug
orientation, and the current mode that was negotiated with
the partner.
This introduces a small API for registering and controlling
cable plug orientation switches, and separate small API for
registering and controlling pin multiplexer/demultiplexer
switches that are needed with Accessory/Alternate Modes.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Tue, 20 Mar 2018 12:57:02 +0000 (15:57 +0300)]
drivers: base: Unified device connection lookup
Several frameworks - clk, gpio, phy, pmw, etc. - maintain
lookup tables for describing connections and provide custom
API for handling them. This introduces a single generic
lookup table and API for the connections.
The motivation for this commit is centralizing the
connection lookup, but the goal is to ultimately extract the
connection descriptions also from firmware by using the
fwnode_graph_* functions and other mechanisms that are
available.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some userspace applications information on the number of
over-current conditions at specific USB hub ports is relevant.
In our case we have a series of USB hardware (using the cp210x driver)
which communicates using a proprietary protocol. These devices sometimes
trigger an over-current situation on some hubs. In case of such an
over-current situation the USB devices offer an interface for reducing
the max used power. As these conditions are quite rare and imply
performance reductions of the device we don't want to reduce the max
power always.
Therefore give user-space applications the possibility to react
adequately by introducing an over_current_counter in the usb port struct
which is exported via sysfs.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reporting two more VID/PID pairs that work with this driver, having used
an informational webpage <http://reboots.g-cipher.net/lcd/> as a buying
guide now. The page listed additional working VID/PID pairs but did not
include these two. None were upstreamed. Also taking this opportunity to
sort the pairs numerically.
Of the two such cables now in my possession, one is white, bearing the
In-System Design ISD-103 label on one side, sold as an Epson CAEUL0002
"USB to Parallel Smart Cable For Apple Macintosh Computers" (04b8:0002),
and the other is black, bearing the In-System Design ISD-101 label on one
side, sold as an early Belkin F5U002 (05ab:0002).
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Mon, 19 Mar 2018 16:26:06 +0000 (00:26 +0800)]
usb: core: Add "quirks" parameter for usbcore
Trying quirks in usbcore needs to rebuild the driver or the entire
kernel if it's builtin. It can save a lot of time if usbcore has similar
ability like "usbhid.quirks=" and "usb-storage.quirks=".
Rename the original quirk detection function to "static" as we introduce
this new "dynamic" function.
Now users can use "usbcore.quirks=" as short term workaround before the
next kernel release. Also, the quirk parameter can XOR the builtin
quirks for debugging purpose.
Thinh Nguyen [Fri, 16 Mar 2018 22:36:17 +0000 (15:36 -0700)]
usb: core: urb: Check SSP isoc ep comp descriptor
The maximum bytes per interval for USB SuperSpeed Plus can be set by
isoc endpoint companion descriptor when it is above 48K. If the
descriptor is provided, then use its value.
Merge tag 'phy-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.17
*) Add USB PHY driver for MDM6600 on Droid
*) Add USB PHY driver for STM32 USB PHY Controller
*) Add inno-usb2-phy driver for hi3798cv200 SoC
*) Add combo phy driver (SATA/USB/PCIE) for HiSilicon STB SoCs
*) Add USB3 PHY driver for Meson GXL and GXM
*) Add support for R8A77965 Gen3 USB 2.0 PHY in phy-rcar-gen3-usb2 driver
*) Add support for qualcomm QUSB2 V2 and QMP V3 USB3 PHY in phy-qcom-qusb2
and phy-qcom-qmp PHY driver respectively
*) Add support for runtime PM in phy-qcom-qusb2 and phy-qcom-qmp PHY drivers
*) Add support for Allwinner R40 USB PHY in sun4i-usb PHY driver
*) Add support in rockchip-typec PHY driver to make extcon optional and
fallback to working in host mode if extcon is missing
*) Add support in rockchip-typec PHY driver to mux PHYs connected to DP
*) Add support to configure slew rate parameters in phy-mtk-tphy PHY driver
*) Add workaround for missing Vbus det interrupts on Allwinner A23/A33
*) Add USB speed related PHY modes in phy core
*) Fix PHY 'structure' documentation
*) Force rockchip-typec PHY to USB2 if DP-only mode is used
*) Fix phy-qcom-qusb2 and phy-qcom-qmp PHY drivers to follow PHY reset and
initialization sequence as per hardware programming manual
*) Fix Marvell BG2CD SoC USB failure in phy-berlin-usb driver
*) Minor fixes in lpc18xx-usb-otg, xusb-tegra210 and phy-rockchip-emmc PHY
drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Linus Torvalds [Sun, 18 Mar 2018 19:03:15 +0000 (12:03 -0700)]
Merge branch 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86/pti updates from Thomas Gleixner:
"Another set of melted spectrum updates:
- Iron out the last late microcode loading issues by actually
checking whether new microcode is present and preventing the CPU
synchronization to run into a timeout induced hang.
- Remove Skylake C2 from the microcode blacklist according to the
latest Intel documentation
- Fix the VM86 POPF emulation which traps if VIP is set, but VIF is
not. Enhance the selftests to catch that kind of issue
- Annotate indirect calls/jumps for objtool on 32bit. This is not a
functional issue, but for consistency sake its the right thing to
do.
- Fix a jump label build warning observed on SPARC64 which uses 32bit
storage for the code location which is casted to 64 bit pointer w/o
extending it to 64bit first.
- Add two new cpufeature bits. Not really an urgent issue, but
provides them for both x86 and x86/kvm work. No impact on the
current kernel"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Fix CPU synchronization routine
x86/microcode: Attempt late loading only when new microcode is present
x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
jump_label: Fix sparc64 warning
x86/speculation, objtool: Annotate indirect calls/jumps for objtool on 32-bit kernels
x86/vm86/32: Fix POPF emulation
selftests/x86/entry_from_vm86: Add test cases for POPF
selftests/x86/entry_from_vm86: Exit with 1 if we fail
x86/cpufeatures: Add Intel PCONFIG cpufeature
x86/cpufeatures: Add Intel Total Memory Encryption cpufeature
Linus Torvalds [Sun, 18 Mar 2018 19:01:14 +0000 (12:01 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for vmalloc_fault() which uses p*d_huge() unconditionally
whether CONFIG_HUGETLBFS is set or not. In case of CONFIG_HUGETLBFS=n
this results in a crash as p*d_huge() returns 0 in that case"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault to use pXd_large
Linus Torvalds [Sun, 18 Mar 2018 18:56:53 +0000 (11:56 -0700)]
Merge branch 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fix from Thomas Gleixner:
"A single fix to prevent partially initialized pointers in mixed mode
(64bit kernel on 32bit UEFI)"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/tpm: Initialize pointer variables to zero for mixed mode
Linus Torvalds [Sun, 18 Mar 2018 18:23:12 +0000 (11:23 -0700)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"PPC:
- fix bug leading to lost IPIs and smp_call_function_many() lockups
on POWER9
ARM:
- locking fix
- reset fix
- GICv2 multi-source SGI injection fix
- GICv2-on-v3 MMIO synchronization fix
- make the console less verbose.
x86:
- fix device passthrough on AMD SME"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: Fix device passthrough when SME is active
kvm: arm/arm64: vgic-v3: Tighten synchronization for guests using v2 on v3
KVM: arm/arm64: vgic: Don't populate multiple LRs with the same vintid
KVM: arm/arm64: Reduce verbosity of KVM init log
KVM: arm/arm64: Reset mapped IRQs on VM reset
KVM: arm/arm64: Avoid vcpu_load for other vcpu ioctls than KVM_RUN
KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending
KVM: PPC: Book3S HV: Fix trap number return from __kvmppc_vcore_entry
parisc: Handle case where flush_cache_range is called with no context
Just when I had decided that flush_cache_range() was always called with
a valid context, Helge reported two cases where the
"BUG_ON(!vma->vm_mm->context);" was hit on the phantom buildd:
This indicates that we need to handle the no context case in
flush_cache_range() as we do in flush_cache_mm().
In thinking about this, I realized that we don't need to flush the TLB
when there is no context. So, I added context checks to the large flush
cases in flush_cache_mm() and flush_cache_range(). The large flush case
occurs frequently in flush_cache_mm() and the change should improve fork
performance.
The v2 version of this change removes the BUG_ON from flush_cache_page()
by skipping the TLB flush when there is no context. I also added code
to flush the TLB in flush_cache_mm() and flush_cache_range() when we
have a context that's not current. Now all three routines handle TLB
flushes in a similar manner.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.9+ Signed-off-by: Helge Deller <deller@gmx.de>
Linus Torvalds [Fri, 16 Mar 2018 20:37:42 +0000 (13:37 -0700)]
Merge tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"There's an important revert in this pull request that needs to go to
stable as it causes a corruption on big endian machines.
The other fix is for FIEMAP incorrectly reporting shared extents
before a sync and one fix for a crash in raid56.
So far we got only one report about the BE corruption, the stable
kernels were out for like a week, so hopefully the scope of the damage
is low"
* tag 'for-4.16-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: use proper endianness accessors for super_copy"
btrfs: add missing initialization in btrfs_check_shared
btrfs: Fix NULL pointer exception in find_bio_stripe
Borislav Petkov [Wed, 14 Mar 2018 18:36:15 +0000 (19:36 +0100)]
x86/microcode: Fix CPU synchronization routine
Emanuel reported an issue with a hang during microcode update because my
dumb idea to use one atomic synchronization variable for both rendezvous
- before and after update - was simply bollocks:
microcode: microcode_reload_late: late_cpus: 4
microcode: __reload_late: cpu 2 entered
microcode: __reload_late: cpu 1 entered
microcode: __reload_late: cpu 3 entered
microcode: __reload_late: cpu 0 entered
microcode: __reload_late: cpu 1 left
microcode: Timeout while waiting for CPUs rendezvous, remaining: 1
CPU1 above would finish, leave and the others will still spin waiting for
it to join.
So do two synchronization atomics instead, which makes the code a lot more
straightforward.
Also, since the update is serialized and it also takes quite some time per
microcode engine, increase the exit timeout by the number of CPUs on the
system.
That's ok because the moment all CPUs are done, that timeout will be cut
short.
Furthermore, panic when some of the CPUs timeout when returning from a
microcode update: we can't allow a system with not all cores updated.
Also, as an optimization, do not do the exit sync if microcode wasn't
updated.
nouveau:
- two backlight fixes
- fix for some lockups
Pretty quiet week, seems like everyone was fixing backlights"
* tag 'drm-fixes-for-v4.16-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/bl: fix backlight regression
drm/nouveau/bl: Fix oops on driver unbind
drm/nouveau/mmu: ALIGN_DOWN correct variable
drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
drm/i915/gvt: Correct the privilege shadow batch buffer address
drm/amdgpu/dce: Don't turn off DP sink when disconnected
drm/amdgpu: save/restore backlight level in legacy dce code
drm/radeon: fix prime teardown order
drm/amdgpu: fix prime teardown order
drm/i915: Kick the rps worker when changing the boost frequency
drm/i915: Only prune fences after wait-for-all
drm/i915: Enable VBT based BL control for DP
drm/i915/gvt: keep oa config in shadow ctx
drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio
In preparation to enabling -Wvla, remove VLA and replace it
with dynamic memory allocation instead.
The use of stack Variable Length Arrays needs to be avoided, as they
can be a vector for stack exhaustion, which can be both a runtime bug
or a security flaw. Also, in general, as code evolves it is easy to
lose track of how big a VLA can get. Thus, we can end up having runtime
failures that are hard to debug.
Also, fixed as part of the directive to remove all VLAs from
the kernel: https://lkml.org/lkml/2018/3/7/621
Notice that in this particular case, an alternative to kzalloc is kcalloc,
in which case the code would look as follows instead:
iv = kcalloc(crypto_skcipher_ivsize(tfm_cbc), sizeof(*iv), GFP_KERNEL);
but if the data type of _iv_ never changes, or the type size is always one
byte, kzalloc is good enough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Fri, 16 Mar 2018 14:33:04 +0000 (16:33 +0200)]
xhci: Clear the host side toggle manually when endpoint is soft reset
Some devices use a clear endpoint halt request as a soft reset, even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side.
xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host
side toggle and sequence, and get it in sync with the device side.
This is a respin of a old patch that was reverted as it had a stale
endpoint context dequeue value which caused regression.
commit 27082e2654dc ("xhci: Clear the host side toggle manually when
endpoint is 'soft reset'")
Mathias Nyman [Fri, 16 Mar 2018 14:33:03 +0000 (16:33 +0200)]
xhci: refactor xhci_urb_enqueue a bit with minor changes
make the local ep_state variable a pointer to the actual ring ep_state.
This allows us to read fresh ep_state values every time, will be useful
later.
Also move the streams check out from bulk only case. Even if only
bulk tranfers can use streams we shouldn't continue if those flags
are set. Main reason for this change is really code readability and
grouping functionality
Mathias Nyman [Fri, 16 Mar 2018 14:33:01 +0000 (16:33 +0200)]
xhci: zero usb device slot_id member when disabling and freeing a xhci slot
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Dan Carpenter [Fri, 16 Mar 2018 14:32:58 +0000 (16:32 +0200)]
usb: xhci: Clean up error code in xhci_dbc_tty_register_device()
tty_port_register_device() returns error pointers on error, never NULL.
The IS_ERR_OR_NULL() function returns either 1 or 0 so it means we
return 1 on error instead of a proper error code. The caller only
checks for zero vs non-zero so this doesn't affect runtime.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The offending patch was merged in 4.16-rc4 and was promptly applied to
stable kernels 4.14.25 and 4.15.8.
The patch causes a corruption in several superblock items on big-endian
machines because of messed up endianity conversions. The damage is
manually repairable. A filesystem cannot be mounted again after it has
been unmounted once.
We do a full revert and not a fixup so stable can pick that patch ASAP.
Fixes: 3c181c12c431 ("btrfs: use proper endianness accessors for super_copy") Link: https://lkml.kernel.org/r/1521139304@msgid.manchmal.in-ulm.de CC: stable@vger.kernel.org # 4.14+ Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: David Sterba <dsterba@suse.com>
Tom Lendacky [Thu, 8 Mar 2018 23:17:31 +0000 (17:17 -0600)]
KVM: x86: Fix device passthrough when SME is active
When using device passthrough with SME active, the MMIO range that is
mapped for the device should not be mapped encrypted. Add a check in
set_spte() to insure that a page is not mapped encrypted if that page
is a device MMIO page as indicated by kvm_is_mmio_pfn().
Cc: <stable@vger.kernel.org> # 4.14.x- Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Michal Simek [Thu, 22 Feb 2018 14:19:37 +0000 (15:19 +0100)]
microblaze: Setup dependencies for ASM optimized lib functions
The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3f86520524711a6f33f3866f9339694)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.
Reported-by: kbuild test robot <fengguang.wu@intel.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
x86/speculation: Remove Skylake C2 from Speculation Control microcode blacklist
In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.
Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Jia Zhang <qianyue.zj@alibaba-inc.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Kyle Huey <me@kylehuey.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain
Thierry Reding [Wed, 14 Mar 2018 10:02:18 +0000 (11:02 +0100)]
phy: tegra: xusb: Uncomment register write
The reason why this was originally commented out is no longer clear. The
UPHY driver for SATA works fine with or without this change. The reset
value of the XDIGCLK_EN bit is 0, so unless programmed by the bootloader
this shouldn't make a difference anyway.
Define a macro for this bit and uncomment the code. This also fixes a
coverity issue brought to my attention by Rohith because not only is the
XDIGCLK_EN field modification commented out, but also the register write
which causes none of the earlier modifications of the register value to
be written to the register and the value being overwritten.
Reported-by: Rohith Seelaboyina <rseelaboyina@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: rockchip-typec: fall back to working in host-mode if extcon is missing.
Right now the rockchip type-c phy does fail probing when no extcon is
detected. Some boards get the cable-state via the extcon interface and
have this supported, other boards seem to use the fusb302 chip or
another but the driver currently does not seem to utilize the extcon
interface to report the cable-state. And, other, just connect the type-c
to a standard USB-A port so use no controller at all. A missing extcon
shouldn't fail to probe, instead, should just fall back to working in
host-mode if it cannot get the extcon.
Fixes: c301b327aea898af ("arm64: dts: rockchip: add usb3-phy otg-port support for rk3399") Reported-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
dt-bindings: phy-rockchip-typec: move extcon property to be optional.
The extcon property is used to detect the cable-state but some boards
just connect the type-c phy to a regular USB-A connector without any
power-delivery and thus no controller reporting the cable-state.
So the extcon property is not really a required property, move it to be
optional instead.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Chris Zhong [Fri, 16 Feb 2018 12:09:55 +0000 (13:09 +0100)]
phy: rockchip-typec: support DP phy switch
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.
Signed-off-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Chris Zhong [Fri, 16 Feb 2018 12:09:54 +0000 (13:09 +0100)]
phy: rockchip-typec: force to USB2 if DP at 4 lanes mode
The usb3tousb2_en BIT will be clear to 0 in probe(), it make USB
controller work at USB3 mode, and if the USB phy is turned on with DP
only mode(4 lanes DP), the rockchip_usb3_phy_power_on() will return
directly, so usb3_host_disable and usb3_host_port these 2 BIT will keep
a same value as coreboot. In coreboot, these 3 BITs are set as USB2
mode, but now one of the bits is changed to USB3, it make USB controller
work at a unknown status.
These 3 BITs should be changed to USB2, if the Type-C works at 4 lanes
mode, and then switch it back to USB3 mode, when USB disconnect.
Signed-off-by: Chris Zhong <zyw@rock-chips.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
William wu [Fri, 16 Feb 2018 12:09:53 +0000 (13:09 +0100)]
phy: rockchip-typec: enable usb3 host during usb3 phy power on
We have forced usb3 to work in usb2 only mode in firmware by setting
usb3tousb2_en (bit3 of GRF_USB3PHY0/1_CON0) to 1, and setting
host_u3_port_disable (bit0 of GRF_USB3OTG0/1_CON1) to 1 and host_u3_port
(bit15~12 of GRF_USB3OTG0/1_CON1) to 0. So we need to re-enable usb3
host.
Note that the RK3399 TRM suggests that we should keep the whole usb3
controller in reset for the duration of the Type-C PHY initialization.
However, it's hard to assert the reset in the current framework of
reset. And according to the TRM, it doesn't require that we should
clear the usb3tousb2 bit before pipe ready. So let's enable the usb3
host after pipe ready to avoid the Type-C PHY initialization failure.
Signed-off-by: William wu <wulf@rock-chips.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
dt-bindings: phy-rockchip-typec: deprecate some register properties.
As now the following register properties are in the driver, document as
deprecated these properties and recommend to not use them on new bindings.
The deprecated properties are:
- rockchip,typec-conn-dir : the register of type-c connector direction
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
enable control.
- rockchip,external-psm : the register of type-c phy external psm clock
selection.
- rockchip,pipe-status : the register of type-c phy pipe status.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: rockchip-typec: deprecate some DT properties for various register fields.
Adding properties for various register fields in the DT doesn't scale and
this information should be in the driver instead.
Before this patch these registers (description below) were specified in
the DT, every register node contained 3 sections: offset, enable bit,
write mask bit.
- rockchip,typec-conn-dir : the register of type-c connector direction,
for type-c phy0, it must be <0xe580 0 16>;
for type-c phy1, it must be <0xe58c 0 16>;
- rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2
enable control.
for type-c phy0, it must be <0xe580 3 19>;
for type-c phy1, it must be <0xe58c 3 19>;
- rockchip,external-psm : the register of type-c phy external psm clock
selection.
for type-c phy0, it must be <0xe588 14 30>;
for type-c phy1, it must be <0xe594 14 30>;
- rockchip,pipe-status : the register of type-c phy pipe status.
for type-c phy0, it must be <0xe5c0 0 0>;
for type-c phy1, it must be <0xe5c0 16 16>;
After this patch these register definitions are in the driver. So can be
removed from the DT. Note that there are 2 type-c phys for RK3399 with
different offsets, the driver checks the phy base address of the running
instance and applies the right offsets.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Tony Lindgren [Fri, 9 Mar 2018 02:37:50 +0000 (18:37 -0800)]
phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4
Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
It is used on some Motorola Mapphone series of phones and tablets such
as Droid 4.
The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
device it seems. We know this as we get L3 errors from omap-usb-host if
trying to use the PHY before MDM6600 is configured.
The GPIOs controlling MDM6600 are used to power device on and off, to
configure the USB start-up mode (normal mode versus USB flashing), and
they also tell the state of the MDM6600 device.
The two start-up mode GPIOs are dual-purposed and used for out of band
(OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
the USB start-up mode first to get MDM6600 booted in the right mode to
be usable in the first place.
Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
driver for modems. But it really does not control the radio at all, it
just controls the modem power and start-up mode for USB. So I came to
the conclusion that we're better off having this done in the USB PHY
driver. For adding support for USB flashing mode, we can later on add
a kernel module option for flash_mode=1 or something similar.
Also note that currently there is no PM runtime support for the OHCI
on omap variant SoCs. So for low(er) power idle states, currenty both
ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.
For reference here is what I measured for total power consumption on
an idle Droid 4 with and without USB related MDM6600 modules:
idle lcd off phy-mapphone-mdm6600 ohci-platform
153mW 284mW 344mW
So it seems that MDM6600 is currently not yet idling even with it's
radio turned off, but that's something that is beyond the control of
this USB PHY driver. This patch does get us to the point where modem
data and GPS are usable with libqmi and ModemManager for example.
Voice calls need more audio driver work.
Cc: devicetree@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Marcel Partap <mpartap@gmx.net> Cc: Michael Scott <michael.scott@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pengcheng Li [Fri, 9 Mar 2018 14:47:01 +0000 (22:47 +0800)]
phy: add inno-usb2-phy driver for hi3798cv200 SoC
It adds inno-usb2-phy driver for hi3798cv200 SoC USB 2.0 support. One
inno-usb2-phy device can support up to two PHY ports. While there is
device level reference clock and power reset to be controlled, each PHY
port has its own utmi reset that needs to assert/de-assert as needed.
Hi3798cv200 needs to access PHY port0 register via particular peripheral
syscon controller register to control PHY, like turning on PHY clock.
Signed-off-by: Pengcheng Li <lpc.li@hisilicon.com> Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com> Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Amelie Delaunay [Fri, 2 Mar 2018 14:56:25 +0000 (15:56 +0100)]
phy: stm32: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds phy transceiver driver for STM32 USB PHY Controller
(USBPHYC) that provides dual port High-Speed phy for OTG (single port)
and EHCI/OHCI host controller (two ports).
One port of the phy is shared between the two USB controllers through
a UTMI+ switch.
[fengguang.wu@intel.com: Make stm32_usbphyc_get_pll_params() to be static] Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Amelie Delaunay [Fri, 2 Mar 2018 14:56:24 +0000 (15:56 +0100)]
dt-bindings: phy: add support for STM32 USB PHY Controller (USBPHYC)
This patch adds the device tree bindings description for STM32 USBPHYC
(USB PHY Controller).
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy: amlogic: add USB3 PHY support for Meson GXL and GXM
This adds a new driver for the USB3 PHY found on Meson GXL and GXM SoCs
(both SoCs are using the same USB PHY register layout).
Unfortunately there is no documentation for this PHY in the public S905X
datasheet (published for example by Khadas). What we know so far about
this PHY:
- even though the Meson GXL and GXM SoCs do not expose an USB3 port (the
dwc3 controller only has USB2 ports enabled) we need to initialize the
USB3 PHY (specifically USB_R1_U3H_FLADJ_30MHZ_REG_MASK). Without this
initialization high-speed USB devices (especially USB hard disks and
thumb drives, slower devices like mice do not seem to be affected)
- on some boards the USB3 PHY starts in "device mode" - we want to bring
it into a known state (by switching it to host mode for now).
- it is responsible for the OTG detection and for switching the first
USB2 PHY between host and peripheral (aka device) mode. an interrupt
can be used to detect changes between host and device mode.
There are five inputs to this register area:
- the clock and reset line for the USB3 PHY itself
- the clock and reset line for the peripheral mode and OTG detection
logic (on the GXL and GXM SoCs these are the same clock and reset line
as for the USB3 PHY itself, but Amlogic sees this as two different
components - even though they share the same register space - so they
have to be passed individually to allow specifying different inputs on
other SoCs if needed)
- the interrupt for the OTG detection logic
The whole OTG detection logic is not implemented yet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Yixun Lan <yixun.lan@amlogic.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
dt-bindings: phy: Add support for the USB3 PHY on Amlogic Meson GXL SoCs
Amlogic Meson GXL SoCs use a dwc3 controller with two (GXM - a variant
for GXL, has three) USB2 ports. The first USB2 port supports host and
peripheral (also called "device") mode.
While the dwc3 controller has no USB3 port enabled we still need the
USB3 PHY to be initialized. Otherwise high-speed USB transfers (for
example with a USB flash drive) may time out (most often seen on boards
with mainline u-boot, where the bootloader does not initialize the USB3
PHY registers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Rob Herring <robh@kernel.org> Tested-by: Yixun Lan <yixun.lan@amlogic.com> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Make the value written into the USB_PHY_RX_CTRL configuration register
match 0xAA79 value written by manufacturer-supplied kernels for Sony
NSZ-GS7 (Berlin2 SoC), Google Chromecast and Valve Steam Link (BG2CD).
This fixes timeouts communicating to the internal hub on Steam Link.
Cc: Kishon Vijay Abraham I <kishon@ti.com> Cc: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Alexander Monakov <amonakov@ispras.ru> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Chunfeng Yun [Mon, 12 Mar 2018 05:25:38 +0000 (13:25 +0800)]
phy: phy-mtk-tphy: keep default value of mcu_bus_ck_gate_en
The default value of mcu_bus_ck_gate_en is 1, if clear it, will
prevent system to enter deep idle mode, so keep its default value
and without affecting PCIe function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Dave Airlie [Fri, 16 Mar 2018 02:51:35 +0000 (12:51 +1000)]
Merge tag 'drm-intel-fixes-2018-03-15' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Only GVT fixes:
- Two warnings fix for runtime pm and usr copy (Xiong, Zhenyu)
- OA context fix for vGPU profiling (Min)
- privilege batch buffer reloc fix (Fred)
* tag 'drm-intel-fixes-2018-03-15' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915/gvt: fix user copy warning by whitelist workload rb_tail field
drm/i915/gvt: Correct the privilege shadow batch buffer address
drm/i915/gvt: keep oa config in shadow ctx
drm/i915/gvt: Add runtime_pm_get/put into gvt_switch_mmio
Linus Torvalds [Fri, 16 Mar 2018 01:57:14 +0000 (18:57 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
- backport-friendly part of lock_parent() race fix
- a fix for an assumption in the heurisic used by path_connected() that
is not true on NFS
- livelock fixes for d_alloc_parallel()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Teach path_connected to handle nfs filesystems with multiple roots.
fs: dcache: Use READ_ONCE when accessing i_dir_seq
fs: dcache: Avoid livelock between d_alloc_parallel and __d_add
lock_parent() needs to recheck if dentry got __dentry_kill'ed under it
Lukas Wunner [Sat, 17 Feb 2018 12:40:23 +0000 (13:40 +0100)]
drm/nouveau/bl: Fix oops on driver unbind
Unbinding nouveau on a dual GPU MacBook Pro oopses because we iterate
over the bl_connectors list in nouveau_backlight_exit() but skipped
initializing it in nouveau_backlight_init(). Stacktrace for posterity:
Fixes: b53ac1ee12a3 ("drm/nouveau/bl: Do not register interface if Apple GMUX detected") Cc: stable@vger.kernel.org # v4.10+ Cc: Pierre Moreau <pierre.morrow@free.fr> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Māris Nartišs [Fri, 16 Mar 2018 01:38:43 +0000 (11:38 +1000)]
drm/nouveau/mmu: ALIGN_DOWN correct variable
Commit 7110c89bb8852ff8b0f88ce05b332b3fe22bd11e ("mmu: swap out round
for ALIGN") replaced two calls to round/rounddown with ALIGN/ALIGN_DOWN,
but erroneously applied ALIGN_DOWN to a different variable (addr) and left
intended variable (tail) not rounded/ALIGNed.
As a result screen corruption, X lockups are observable. An example of kernel
log of affected system with NV98 card where it was bisected:
nouveau 0000:01:00.0: gr: TRAP_M2MF 00000002 [IN]
nouveau 0000:01:00.0: gr: TRAP_M2MF 00320951400007c00000000004000000
nouveau 0000:01:00.0: gr: 00200000 [] ch 1 [000fbbe000 DRM] subc 4 class 5039
mthd 0100 data 00000000
nouveau 0000:01:00.0: fb: trapped read at 0040000000 on channel 1
[0fbbe000 DRM]
engine 00 [PGRAPH] client 03 [DISPATCH] subclient 04 [M2M_IN] reason 00000006
[NULL_DMAOBJ]
Fixes bug 105173 ("[MCP79][Regression] Unhandled NULL pointer dereference in
nvkm_object_unmap since kernel 4.15")
https://bugs.freedesktop.org/show_bug.cgi?id=105173
Fixes: 7110c89bb885 ("mmu: swap out round for ALIGN ") Tested-by: Pierre Moreau <pierre.morrow@free.fr> Reviewed-by: Pierre Moreau <pierre.morrow@free.fr> Signed-off-by: Maris Nartiss <maris.nartiss@gmail.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Cc: stable@vger.kernel.org # v4.15+
fs: Teach path_connected to handle nfs filesystems with multiple roots.
On nfsv2 and nfsv3 the nfs server can export subsets of the same
filesystem and report the same filesystem identifier, so that the nfs
client can know they are the same filesystem. The subsets can be from
disjoint directory trees. The nfsv2 and nfsv3 filesystems provides no
way to find the common root of all directory trees exported form the
server with the same filesystem identifier.
The practical result is that in struct super s_root for nfs s_root is
not necessarily the root of the filesystem. The nfs mount code sets
s_root to the root of the first subset of the nfs filesystem that the
kernel mounts.
This effects the dcache invalidation code in generic_shutdown_super
currently called shrunk_dcache_for_umount and that code for years
has gone through an additional list of dentries that might be dentry
trees that need to be freed to accomodate nfs.
When I wrote path_connected I did not realize nfs was so special, and
it's hueristic for avoiding calling is_subdir can fail.
The practical case where this fails is when there is a move of a
directory from the subtree exposed by one nfs mount to the subtree
exposed by another nfs mount. This move can happen either locally or
remotely. With the remote case requiring that the move directory be cached
before the move and that after the move someone walks the path
to where the move directory now exists and in so doing causes the
already cached directory to be moved in the dcache through the magic
of d_splice_alias.
If someone whose working directory is in the move directory or a
subdirectory and now starts calling .. from the initial mount of nfs
(where s_root == mnt_root), then path_connected as a heuristic will
not bother with the is_subdir check. As s_root really is not the root
of the nfs filesystem this heuristic is wrong, and the path may
actually not be connected and path_connected can fail.
The is_subdir function might be cheap enough that we can call it
unconditionally. Verifying that will take some benchmarking and
the result may not be the same on all kernels this fix needs
to be backported to. So I am avoiding that for now.
Filesystems with snapshots such as nilfs and btrfs do something
similar. But as the directory tree of the snapshots are disjoint
from one another and from the main directory tree rename won't move
things between them and this problem will not occur.
Cc: stable@vger.kernel.org Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Fixes: 397d425dc26d ("vfs: Test for and handle paths that are unreachable from their mnt_root") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David S. Miller [Thu, 15 Mar 2018 21:18:00 +0000 (14:18 -0700)]
sparc64: Fix regression in pmdp_invalidate().
pmdp_invalidate() was changed to update the pmd atomically
(to not lose dirty/access bits) and return the original pmd
value.
However, in doing so, we lost a lot of the essential work that
set_pmd_at() does, namely to update hugepage mapping counts and
queuing up the batched TLB flush entry.
Thus we were not flushing entries out of the TLB when making
such PMD changes.
Fix this by abstracting the accounting work of set_pmd_at() out into a
separate function, and call it from pmdp_establish().
Fixes: a8e654f01cb7 ("sparc64: update pmdp_invalidate() to return old pmd value") Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Bonzini [Thu, 15 Mar 2018 20:45:37 +0000 (21:45 +0100)]
Merge tag 'kvm-arm-fixes-for-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
kvm/arm fixes for 4.16, take 2
- Peace of mind locking fix in vgic_mmio_read_pending
- Allow hw-mapped interrupts to be reset when the VM resets
- Fix GICv2 multi-source SGI injection
- Fix MMIO synchronization for GICv2 on v3 emulation
- Remove excess verbosity on the console
Linus Torvalds [Thu, 15 Mar 2018 18:04:46 +0000 (11:04 -0700)]
Merge tag 'for-4.16/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a stable DM multipath fix to restore ability to pass integrity data
- two DM multipath fixes for a fix that was merged into 4.16-rc5
* tag 'for-4.16/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm mpath: fix passing integrity data
dm mpath: eliminate need to use scsi_device_from_queue
dm mpath: fix uninitialized 'pg_init_wait' waitqueue_head NULL pointer
By whitelist guest page write from workload struct allocated from kmem cache.
Reviewed-by: Hang Yuan <hang.yuan@linux.intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
(cherry picked from commit 5627705406874df57fdfad3b4e0c9aedd3b007df)
fred gao [Thu, 15 Mar 2018 05:21:10 +0000 (13:21 +0800)]
drm/i915/gvt: Correct the privilege shadow batch buffer address
Once the ring buffer is copied to ring_scan_buffer and scanned,
the shadow batch buffer start address is only updated into
ring_scan_buffer, not the real ring address allocated through
intel_ring_begin in later copy_workload_to_ring_buffer.
This patch is only to set the right shadow batch buffer address
from Ring buffer, not include the shadow_wa_ctx.
v2:
- refine some comments. (Zhenyu)
v3:
- fix typo in title. (Zhenyu)
v4:
- remove the unnecessary comments. (Zhenyu)
- add comments in bb_start_cmd_va update. (Zhenyu)
Fixes: 0a53bc07f044 ("drm/i915/gvt: Separate cmd scan from request allocation") Cc: stable@vger.kernel.org # v4.15 Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Yulei Zhang <yulei.zhang@intel.com> Signed-off-by: fred gao <fred.gao@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Linus Torvalds [Thu, 15 Mar 2018 00:02:49 +0000 (17:02 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is four patches, consisting of one regression from the merge
window (qla2xxx), one long-standing memory leak (sd_zbc), one event
queue mislabelling which we want to eliminate to discourage the
pattern (mpt3sas), and one behaviour change because re-reading the
partition table shouldn't clear the ro flag"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Keep disk read-only when re-reading partition
scsi: qla2xxx: Fix crashes in qla2x00_probe_one on probe failure
scsi: sd_zbc: Fix potential memory leak
scsi: mpt3sas: Do not mark fw_event workqueue as WQ_MEM_RECLAIM
Joern Engel [Tue, 13 Mar 2018 18:36:49 +0000 (11:36 -0700)]
btree: avoid variable-length allocations
geo->keylen cannot be larger than 4. So we might as well make
fixed-size allocations.
Given the one remaining user, geo->keylen cannot even be larger than 1.
Logfs used to have 64bit and 128bit keys, tcm_qla2xxx only has 32bit
keys. But let's not break the code if we don't have to.
Signed-off-by: Joern Engel <joern@purestorage.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 14 Mar 2018 23:51:33 +0000 (16:51 -0700)]
Merge branch 'percpu_ref-rcu-audit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc
Pull percpu_ref rcu fixes from Tejun Heo:
"Jann Horn found that aio was depending on the internal RCU grace
periods of percpu-ref and that it's broken because aio uses regular
RCU while percpu_ref uses sched-RCU.
Depending on percpu_ref's internal grace periods isn't a good idea
because
- The RCU type might not match.
- percpu_ref's grace periods are used to switch to atomic mode. They
aren't between the last put and the invocation of the last release.
This is easy to get confused about and can lead to subtle bugs.
- percpu_ref might not have grace periods at all depending on its
current operation mode.
This patchset audits and fixes percpu_ref users for their RCU usages"
[ There's a continuation of this series that clarifies percpu_ref
documentation that the internal grace periods must not be depended
upon, and introduces rcu_work to simplify bouncing to a workqueue
after an RCU grace period.
That will go in for 4.17 - this is just the minimal set with the fixes
that are tagged for -stable ]
* 'percpu_ref-rcu-audit-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/misc:
RDMAVT: Fix synchronization around percpu_ref
fs/aio: Use RCU accessors for kioctx_table->table[]
fs/aio: Add explicit RCU grace period when freeing kioctx
Commit 864b75f9d6b0 ("mm/page_alloc: fix memmap_init_zone pageblock
alignment") modified the logic in memmap_init_zone() to initialize
struct pages associated with invalid PFNs, to appease a VM_BUG_ON()
in move_freepages(), which is redundant by its own admission, and
dereferences struct page fields to obtain the zone without checking
whether the struct pages in question are valid to begin with.
Commit 864b75f9d6b0 only makes it worse, since the rounding it does
may cause pfn assume the same value it had in a prior iteration of
the loop, resulting in an infinite loop and a hang very early in the
boot. Also, since it doesn't perform the same rounding on start_pfn
itself but only on intermediate values following an invalid PFN, we
may still hit the same VM_BUG_ON() as before.
So instead, let's fix this at the core, and ensure that the BUG
check doesn't dereference struct page fields of invalid pages.
Fixes: 864b75f9d6b0 ("mm/page_alloc: fix memmap_init_zone pageblock alignment") Tested-by: Jan Glauber <jglauber@cavium.com> Tested-by: Shanker Donthineni <shankerd@codeaurora.org> Cc: Daniel Vacek <neelx@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michal Hocko <mhocko@suse.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Airlie [Wed, 14 Mar 2018 23:26:11 +0000 (09:26 +1000)]
Merge tag 'drm-intel-fixes-2018-03-14' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- 1 display fix for bxt
- 1 gem fix for fences
- 1 gem/pm fix for rps freq
* tag 'drm-intel-fixes-2018-03-14' of git://anongit.freedesktop.org/drm/drm-intel:
drm/i915: Kick the rps worker when changing the boost frequency
drm/i915: Only prune fences after wait-for-all
drm/i915: Enable VBT based BL control for DP
Dave Airlie [Wed, 14 Mar 2018 23:23:54 +0000 (09:23 +1000)]
Merge branch 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
A few fixes for 4.16:
- Fix a backlight S/R regression on amdgpu
- Fix prime teardown on radeon and amdgpu
- DP fix for amdgpu
* 'drm-fixes-4.16' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu/dce: Don't turn off DP sink when disconnected
drm/amdgpu: save/restore backlight level in legacy dce code
drm/radeon: fix prime teardown order
drm/amdgpu: fix prime teardown order
wrote 65536/65536 bytes at offset 0
64 KiB, 4 ops; 0.0000 sec (121.359 MiB/sec and 7766.9903 ops/sec)
/media/scratch/file5:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 24576..24703 128 0x2001
/media/scratch/file5:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 24576..24703 128 0x1
This is because btrfs_check_shared calls find_parent_nodes
repeatedly in a loop, passing a share_check struct to report
the count of shared extent. But btrfs_check_shared does not
re-initialize the count value to zero for subsequent calls
from the loop, resulting in a false share count value. This
is a regressive behavior from 4.13.
With proper re-initialization the test result is as follows:
wrote 65536/65536 bytes at offset 0
64 KiB, 4 ops; 0.0000 sec (110.035 MiB/sec and 7042.2535 ops/sec)
/media/scratch/file5:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 24576..24703 128 0x1
/media/scratch/file5:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 24576..24703 128 0x1
which corrects the regression.
Fixes: 3ec4d3238ab ("btrfs: allow backref search checks for shared extents") Signed-off-by: Edmund Nadolski <enadolski@suse.com>
[ add text from cover letter to changelog ] Signed-off-by: David Sterba <dsterba@suse.com>
This is reproducible in a cycle, where a series of writes is followed by
SCSI device delete command. The test may take up to few minutes.
Fixes: 74d46992e0d9 ("block: replace bi_bdev with a gendisk pointer and partitions index")
[ no signed-off-by provided ]
Author: Dmitriy Gorokh <Dmitriy.Gorokh@wdc.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Alex Deucher [Thu, 8 Mar 2018 14:56:01 +0000 (09:56 -0500)]
drm/amdgpu: save/restore backlight level in legacy dce code
Save/restore the backlight level scratch register in S3/S4 so the
backlight level comes back at the previously requested level.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=199047 Fixes: 4ec6ecf48c64d (drm/amdgpu: drop scratch regs save and restore from S3/S4 handling) Acked-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 9 Mar 2018 13:44:32 +0000 (14:44 +0100)]
drm/radeon: fix prime teardown order
We unmapped imported DMA-bufs when the GEM handle was dropped, not when the
hardware was done with the buffere.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> CC: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Fri, 9 Mar 2018 13:42:54 +0000 (14:42 +0100)]
drm/amdgpu: fix prime teardown order
We unmapped imported DMA-bufs when the GEM handle was dropped, not when the
hardware was done with the buffere.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> CC: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>