netdevsim: move device registration and related code to bus.c
Move netdevsim device registration into bus.c and alongside with that
the related sysfs attributes. Introduce new struct nsim_bus_dev to
represent a netdevsim device on netdevsim bus.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: rename devlink.c to dev.c to contain per-dev(asic) items
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netdevsim: create devlink instance per netdevsim instance
Currently there is one devlink instance created per network namespace.
That is quite odd considering the fact that devlink instance should
represent an ASIC. The following patches are going to move the devlink
instance even more down to a bus device, but until then, have one
devlink instance per netdevsim instance. Struct nsim_devlink is
introduced to hold fib setting.
The changes in the fib code are only related to holding the
configuration per devlink instance instead of network namespace.
Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: Align minimum encryption key size for LE and BR/EDR connections
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
Pull networking fixes from David Miller:
"Just the usual assortment of small'ish fixes:
1) Conntrack timeout is sometimes not initialized properly, from
Alexander Potapenko.
2) Add a reasonable range limit to tcp_min_rtt_wlen to avoid
undefined behavior. From ZhangXiaoxu.
3) des1 field of descriptor in stmmac driver is initialized with the
wrong variable. From Yue Haibing.
4) Increase mlxsw pci sw reset timeout a little bit more, from Ido
Schimmel.
5) Match IOT2000 stmmac devices more accurately, from Su Bao Cheng.
6) Fallback refcount fix in TLS code, from Jakub Kicinski.
7) Fix max MTU check when using XDP in mlx5, from Maxim Mikityanskiy.
8) Fix recursive locking in team driver, from Hangbin Liu.
9) Fix tls_set_device_offload_Rx() deadlock, from Jakub Kicinski.
10) Don't use napi_alloc_frag() outside of softiq context of socionext
driver, from Ilias Apalodimas.
11) MAC address increment overflow in ncsi, from Tao Ren.
12) Fix a regression in 8K/1M pool switching of RDS, from Zhu Yanjun.
13) ipv4_link_failure has to validate the headers that are actually
there because RAW sockets can pass in arbitrary garbage, from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add sanity checks in ipv4_link_failure()
net/rose: fix unbound loop in rose_loopback_timer()
rxrpc: fix race condition in rxrpc_input_packet()
net: rds: exchange of 8K and 1M pool
net: vrf: Fix operation not supported when set vrf mac
net/ncsi: handle overflow when incrementing mac address
net: socionext: replace napi_alloc_frag with the netdev variant on init
net: atheros: fix spelling mistake "underun" -> "underrun"
spi: ST ST95HF NFC: declare missing of table
spi: Micrel eth switch: declare missing of table
net: stmmac: move stmmac_check_ether_addr() to driver probe
netfilter: fix nf_l4proto_log_invalid to log invalid packets
netfilter: never get/set skb->tstamp
netfilter: ebtables: CONFIG_COMPAT: drop a bogus WARN_ON
Documentation: decnet: remove reference to CONFIG_DECNET_ROUTE_FWMARK
dt-bindings: add an explanation for internal phy-mode
net/tls: don't leak IV and record seq when offload fails
net/tls: avoid potential deadlock in tls_set_device_offload_rx()
selftests/net: correct the return value for run_afpackettests
team: fix possible recursive locking when add slaves
...
Merge tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED update from Jacek Anaszewski:
"A single change to MAINTAINERS:
We announce a new LED reviewer - Dan Murphy"
* tag 'leds-for-5.1-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: LEDs: Add designated reviewer for LED subsystem
Eric Dumazet [Wed, 24 Apr 2019 15:04:05 +0000 (08:04 -0700)]
ipv4: add sanity checks in ipv4_link_failure()
Before calling __ip_options_compile(), we need to ensure the network
header is a an IPv4 one, and that it is already pulled in skb->head.
RAW sockets going through a tunnel can end up calling ipv4_link_failure()
with total garbage in the skb, or arbitrary lengthes.
syzbot report :
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:355 [inline]
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0x294/0x1120 net/ipv4/ip_options.c:123
Write of size 69 at addr ffff888096abf068 by task syz-executor.4/9204
Fixes: ed0de45a1008 ("ipv4: recompile ip options in ipv4_link_failure") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Suryaputra <ssuryaextr@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 24 Apr 2019 16:44:11 +0000 (09:44 -0700)]
rxrpc: fix race condition in rxrpc_input_packet()
After commit 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook"),
rxrpc_input_packet() is directly called from lockless UDP receive
path, under rcu_read_lock() protection.
It must therefore use RCU rules :
- udp_sk->sk_user_data can be cleared at any point in this function.
rcu_dereference_sk_user_data() is what we need here.
- Also, since sk_user_data might have been set in rxrpc_open_socket()
we must observe a proper RCU grace period before kfree(local) in
rxrpc_lookup_local()
v4: @local can be NULL in xrpc_lookup_local() as reported by kbuild test robot <lkp@intel.com>
and Julia Lawall <julia.lawall@lip6.fr>, thanks !
v3,v2 : addressed David Howells feedback, thanks !
Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Before the commit 490ea5967b0d ("RDS: IB: move FMR code to its own file"),
when the dirty_count is greater than 9/10 of max_items of 8K pool,
1M pool is used, Vice versa. After the commit 490ea5967b0d ("RDS: IB: move
FMR code to its own file"), the above is removed. When we make the
following tests.
Server:
rds-stress -r 1.1.1.16 -D 1M
Client:
rds-stress -r 1.1.1.14 -s 1.1.1.16 -D 1M
The following will appear.
"
connecting to 1.1.1.16:4000
negotiated options, tasks will start in 2 seconds
Starting up..header from 1.1.1.166:4001 to id 4001 bogus
..
tsks tx/s rx/s tx+rx K/s mbi K/s mbo K/s tx us/c rtt us
cpu %
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
1 0 0 0.00 0.00 0.00 0.00 0.00 -1.00
...
"
So this exchange between 8K and 1M pool is added back.
Fixes: commit 490ea5967b0d ("RDS: IB: move FMR code to its own file") Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: sched: flower: refactor reoffload for concurrent access
Recent changes that introduced unlocked flower did not properly account for
case when reoffload is initiated concurrently with filter updates. To fix
the issue, extend flower with 'hw_filters' list that is used to store
filters that don't have 'skip_hw' flag set. Filter is added to the list
when it is inserted to hardware and only removed from it after being
unoffloaded from all drivers that parent block is attached to. This ensures
that concurrent reoffload can still access filter that is being deleted and
prevents race condition when driver callback can be removed when filter is
no longer accessible trough idr, but is still present in hardware.
Refactor fl_change() to respect new filter reference counter and to release
filter reference with __fl_put() in case of error, instead of directly
deallocating filter memory. This allows for concurrent access to filter
from fl_reoffload() and protects it with reference counting. Refactor
fl_reoffload() to iterate over hw_filters list instead of idr. Implement
fl_get_next_hw_filter() helper function that is used to iterate over
hw_filters list with reference counting and skips filters that are being
concurrently deleted.
Fixes: 92149190067d ("net: sched: flower: set unlocked flag for flower proto ops") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 16:24:46 +0000 (09:24 -0700)]
tipc: tipc_udp_recv() cleanup vs rcu verbs
First thing tipc_udp_recv() does is to use rcu_dereference_sk_user_data(),
and this is really hinting we already own rcu_read_lock() from the caller
(UDP stack).
No need to add another rcu_read_lock()/rcu_read_unlock() pair.
Also use rcu_dereference() instead of rcu_dereference_rtnl()
in the data path.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Bluetooth: hci_core: Don't stop BT if the BD address missing in dts
When flag HCI_QUIRK_USE_BDADDR_PROPERTY is set, we will read the
bluetooth address from dts. If the bluetooth address node is missing
from the dts we will enable it controller UNCONFIGURED state.
This patch enables the normal flow even if the BD address is missing
from the dts tree.
David Ahern [Wed, 24 Apr 2019 01:05:33 +0000 (18:05 -0700)]
ipv6: Use result arg in fib_lookup_arg consistently
arg.result is sometimes used as fib6_result and sometimes used to
hold the rt6_info. Add rt6_info to fib6_result and make the use
of arg.result consistent through ipv6 rules.
The rt6 entry is filled in for lookups returning a dst_entry, but not
for direct fib_lookups that just want a fib6_info.
Fixes: effda4dd97e8 ("ipv6: Pass fib6_result to fib lookups") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Wed, 24 Apr 2019 01:06:30 +0000 (18:06 -0700)]
ipv6: fib6_rule_action_alt needs to return -EAGAIN
fib rule actions should return -EAGAIN for the rules to continue to the
next one. A recent change overwrote err with the lookup always returning
0 (future change will make it more like IPv4) which means the rules
stopped at the first (e.g., local table lookup only). Catch and reset err
to -EAGAIN.
Fixes: effda4dd97e87 ("ipv6: Pass fib6_result to fib lookups") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Tao Ren [Wed, 24 Apr 2019 01:43:32 +0000 (01:43 +0000)]
net/ncsi: handle overflow when incrementing mac address
Previously BMC's MAC address is calculated by simply adding 1 to the
last byte of network controller's MAC address, and it produces incorrect
result when network controller's MAC address ends with 0xFF.
The problem can be fixed by calling eth_addr_inc() function to increment
MAC address; besides, the MAC address is also validated before assigning
to BMC.
Fixes: cb10c7c0dfd9 ("net/ncsi: Add NCSI Broadcom OEM command") Signed-off-by: Tao Ren <taoren@fb.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm
Pull drm regression fixes from Dave Airlie:
"We interrupt your regularly scheduled drm fixes for a regression
special.
The first is for a fix in i915 that had unexpected side effects
fallout in the userspace X.org modesetting driver where X would no
longer start. I got tired of the nitpicking and issued a large hammer
on it. The X.org driver is buggy, but blackscreen regressions are
worse.
The second was an oversight that myself and Gerd should have noticed
better, Gerd is trying to fix this properly, but the regression is too
large to leave, even if the original behaviour is bad in some cases,
it's clearly bad to break a bunch of working use cases.
I'll likely have a regular fixes pull later, but I really wanted to
highlight these"
* tag 'drm-fixes-2019-04-24' of git://anongit.freedesktop.org/drm/drm:
Revert "drm/virtio: drop prime import/export callbacks"
Revert "drm/i915/fbdev: Actually configure untiled displays"
David Ahern [Tue, 23 Apr 2019 23:03:29 +0000 (16:03 -0700)]
mlxsw: spectrum_router: Prevent ipv6 gateway with v4 route via replace and append
mlxsw currently does not support v6 gateways with v4 routes. Commit 19a9d136f198 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway")
prevents a route from being added, but nothing stops the replace or
append. Add a catch for them too.
$ ip ro add 172.16.2.0/24 via 10.99.1.2
$ ip ro replace 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
$ ip ro append 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Apr 2019 02:52:33 +0000 (19:52 -0700)]
Merge branch 'Taprio-qdisc-fixes'
Andre Guedes says:
====================
Taprio qdisc fixes
I'm re-sending this series, now with the "net-next" prefix in the subject.
The only change from the previous version is in patch 3. As suggested by Cong
Wang, it removes the !entry check within should_restart_cycle() since it is
already checked by the caller. As a side effect, that function becomes a dummy
wrapper on list_is_last() so we simply remove it and call list_is_last()
instead.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:24 +0000 (12:44 -0700)]
net: sched: taprio: Fix taprio_dequeue()
In case we don't have 'guard' or 'budget' to transmit the skb, we should
continue traversing the qdisc list since the remaining guard/budget
might be enough to transmit a skb from other children qdiscs.
Fixes: 5a781ccbd19e (“tc: Add support for configuring the taprio scheduler”) Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:23 +0000 (12:44 -0700)]
net: sched: taprio: Fix taprio_peek()
While traversing taprio's children qdisc list, if the gate is closed for
a given traffic class, we should continue traversing the list since the
remaining qdiscs may have skb ready for transmission.
This patch also takes this opportunity and changes the function to use
the TAPRIO_ALL_GATES_OPEN macro instead of the magic number '-1'.
Fixes: 5a781ccbd19e (“tc: Add support for configuring the taprio scheduler”) Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Guedes [Tue, 23 Apr 2019 19:44:22 +0000 (12:44 -0700)]
net: sched: taprio: Remove should_restart_cycle()
The 'entry' argument from should_restart_cycle() cannot be NULL since it
is already checked by the caller so the WARN_ON() within should_
restart_cycle() could be removed. By doing that, that function becomes
a dummy wrapper on list_is_last() so this patch simply gets rid of it
and call list_is_last() within advance_sched() instead.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does a code refactoring to taprio_get_start_time() function
to improve readability and report error properly.
If 'base' time is later than 'now', the start time is equal to 'base'
and taprio_get_start_time() is done. That's the natural case so we move
that code to the beginning of the function. Also, if 'cycle' calculation
is zero, something went really wrong with taprio and we should log that
internal error properly.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a pointless variable assigment in taprio_change().
The 'err' variable is not used from this assignment to the next one so
this patch removes it.
Signed-off-by: Andre Guedes <andre.guedes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Apr 2019 15:48:09 +0000 (08:48 -0700)]
net: Change nhc_flags to unsigned char
nhc_flags holds the RTNH_F flags for a given nexthop (fib{6}_nh).
All of the RTNH_F_ flags fit in an unsigned char, and since the API to
userspace (rtnh_flags and lower byte of rtm_flags) is 1 byte it can not
grow. Make nhc_flags in fib_nh_common an unsigned char and shrink the
size of the struct by 8, from 56 to 48 bytes.
Update the flags arguments for up netdevice events and fib_nexthop_info
which determines the RTNH_F flags to return on a dump/event. The RTNH_F
flags are passed in the lower byte of rtm_flags which is an unsigned int
so use a temp variable for the flags to fib_nexthop_info and combine
with rtm_flags in the caller.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Apr 2019 15:23:41 +0000 (08:23 -0700)]
lwtunnel: Pass encap and encap type attributes to lwtunnel_fill_encap
Currently, lwtunnel_fill_encap hardcodes the encap and encap type
attributes as RTA_ENCAP and RTA_ENCAP_TYPE, respectively. The nexthop
objects want to re-use this code but the encap attributes passed to
userspace as NHA_ENCAP and NHA_ENCAP_TYPE. Since that is the only
difference, change lwtunnel_fill_encap to take the attribute type as
an input.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: socionext: replace napi_alloc_frag with the netdev variant on init
The netdev variant is usable on any context since it disables interrupts.
The napi variant of the call should only be used within softirq context.
Replace napi_alloc_frag on driver init with the correct netdev_alloc_frag
call
Changes since v1:
- Adjusted commit message
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by: Jassi Brar <jaswinder.singh@linaro.org> Fixes: 4acb20b46214 ("net: socionext: different approach on DMA") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman [Tue, 23 Apr 2019 13:01:53 +0000 (15:01 +0200)]
ravb: Avoid unsupported internal delay mode for R-Car E3/D3
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995). And by extension it is also not supported by RZ/G2E (r9a774c0).
This matches all ES versions of the affected SoCs as it is
not clear if this problem will be resolved in newer chips.
This can be revisited, as necessary.
This patch does not error-out if PHY_INTERFACE_MODE_RGMII_ID or
PHY_INTERFACE_MODE_RGMII_TXID are used on SoCs where TX clock delay
mode is not supported as there is a risk of introducing a regression
when used in conjunction with older DT blobs present in the field.
Rather, a warning is logged in such cases.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Rothwell [Tue, 23 Apr 2019 07:25:24 +0000 (17:25 +1000)]
net: fix sparc64 compilation of sock_gettstamp
net/core/sock.c: In function 'sock_gettstamp':
net/core/sock.c:3007:23: error: expected '}' before ';' token
.tv_sec = ts.tv_sec;
^
net/core/sock.c:3011:4: error: expected ')' before 'return'
return -EFAULT;
^~~~~~
net/core/sock.c:3013:2: error: expected expression before '}' token
}
^
Fixes: c7cbdbf29f48 ("net: rework SIOCGSTAMP ioctl handling") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers should be printed with %p or %px rather than
cast to (u_long) and printed with %lx.
Change %lx to %p to print the pointer.
Change %lx to %pad to print the dma_addr_t.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pointers should be printed with %p or %px rather than
cast to (u_long) type and printed with %lX.
As the function seems to be for debug purpose.
Change %lX to %px to print the pointer value.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Airlie [Wed, 24 Apr 2019 00:52:20 +0000 (10:52 +1000)]
Revert "drm/virtio: drop prime import/export callbacks"
This patch does more harm than good, as it breaks both Xwayland and
gnome-shell with X11.
Xwayland requires DRI3 & DRI3 requires PRIME.
X11 crash for obscure double-free reason which are hard to debug
(starting X11 by hand doesn't trigger the crash).
I don't see an apparent problem implementing those stub prime
functions, they may return an error at run-time, and it seems to be
handled fine by GNOME at least.
This brings back the original problem, but it's better than regressions.]
Fixes: b318e3ff7ca065d6b107e424c85a63d7a6798a ("drm/virtio: drop prime import/export callbacks") Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit is documented to break userspace X.org modesetting driver in certain configurations.
The X.org modesetting userspace driver is broken. No fixes are available yet. In order for this patch to be applied it either needs a config option or a workaround developed.
This has been reported a few times, saying it's a userspace problem is clearly against the regression rules.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109806 Signed-off-by: Dave Airlie <airlied@redhat.com> Cc: <stable@vger.kernel.org> # v3.19+
Eric Dumazet [Tue, 23 Apr 2019 01:35:03 +0000 (18:35 -0700)]
ipv6: convert fib6_ref to refcount_t
We suspect some issues involving fib6_ref 0 -> 1 transitions might
cause strange syzbot reports.
Lets convert fib6_ref to refcount_t to catch them earlier.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Acked-by: Wei Wang <weiwan@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 01:35:02 +0000 (18:35 -0700)]
ipv6: broadly use fib6_info_hold() helper
Instead of using atomic_inc(), prefer fib6_info_hold()
so that upcoming refcount_t conversion is simpler.
Only fib6_info_alloc() is using atomic_set() since we
just allocated a new object.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Acked-by: Wei Wang <weiwan@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 23 Apr 2019 01:35:01 +0000 (18:35 -0700)]
ipv6: fib6_info_destroy_rcu() cleanup
We do not need to clear f6i->rt6i_exception_bucket right before
freeing f6i.
Note that f6i->rt6i_exception_bucket is properly protected by
f6i->exception_bucket_flushed being set to one in rt6_flush_exceptions()
under the protection of rt6_exception_lock.
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Wei Wang <weiwan@google.com> Acked-by: Wei Wang <weiwan@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Apr 2019 00:03:40 +0000 (17:03 -0700)]
Merge tag 'mlx5-updates-2019-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-04-22
This series includes updates to mlx5e driver RX data path and some
significant XDP RX/TX improvements to overcome/mitigate HW and PCIE
bottlenecks.
From Tariq:
1) Some Enhancements in rq->flags
2) Stabilize RX packet rate (on Striding RQ) with
multiple outstanding UMR posts
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
From Shay:
3) XDP, Inline small packets into the TX MPWQE in XDP xmit flow
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
From Maxim:
4) Some trivial refactoring and code improvements prior to a larger series
to support AF_XDP.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'nfsd-5.1-1' of git://linux-nfs.org/~bfields/linux
Pull nfsd bugfixes from Bruce Fields:
"Fix miscellaneous nfsd bugs, in NFSv4.1 callbacks, NFSv4.1
lock-notification callbacks, NFSv3 readdir encoding, and the
cache/upcall code"
* tag 'nfsd-5.1-1' of git://linux-nfs.org/~bfields/linux:
nfsd: wake blocked file lock waiters before sending callback
nfsd: wake waiters blocked on file_lock before deleting it
nfsd: Don't release the callback slot unless it was actually held
nfsd/nfsd3_proc_readdir: fix buffer count and page pointers
sunrpc: don't mark uninitialised items as VALID.
Merge tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull syscall numbering updates from Arnd Bergmann:
"arch: add pidfd and io_uring syscalls everywhere
This comes a bit late, but should be in 5.1 anyway: we want the newly
added system calls to be synchronized across all architectures in the
release.
I hope that in the future, any newly added system calls can be added
to all architectures at the same time, and tested there while they are
in linux-next, avoiding dependencies between the architecture
maintainer trees and the tree that contains the new system call"
* tag 'syscalls-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
arch: add pidfd and io_uring syscalls everywhere
Bluetooth: hci_qca: Fix crash with non-serdev devices
qca_set_baudrate() calls serdev_device_wait_until_sent() assuming that
the HCI is always associated with a serdev device. This isn't true for
ROME controllers instantiated through ldisc, where the call causes a
crash due to a NULL pointer dereferentiation. Only call the function
when we have a serdev device. The timeout for ROME devices at the end
of qca_set_baudrate() is long enough to be reasonably sure that the
command was sent.
net/mlx5e: Take HW interrupt trigger into a function
mlx5e_trigger_irq posts a NOP to the ICO SQ just to trigger an IRQ and
enter the NAPI poll on the right CPU according to the affinity. Use it
in mlx5e_activate_rq.
mlx5e_mpwqe_get_log_rq_size calculates the number of WQEs (N) based on
the requested number of frames in the RQ (F) and the number of packets
per WQE (P). It ensures that N is not less than the minimum number of
WQEs in an RQ (N_min). Arithmetically, it means that F / P >= N_min
should be true. This function deals with logarithms, so it should check
that log(F) - log(P) >= log(N_min). However, if F < P, this expression
will cause an unsigned underflow. Check log(F) >= log(P) + log(N_min)
instead.
If the channels fail to reopen after setting an XDP program, return the
error code instead of 0. A proper fix is still needed, as now any error
while reopening the channels brings the interface down. This patch only
adds error reporting.
Shay Agroskin [Thu, 14 Mar 2019 12:54:07 +0000 (14:54 +0200)]
net/mlx5e: XDP, Inline small packets into the TX MPWQE in XDP xmit flow
Upon high packet rate with multiple CPUs TX workloads, much of the HCA's
resources are spent on prefetching TX descriptors, thus affecting
transmission rates.
This patch comes to mitigate this problem by moving some workload to the
CPU and reducing the HW data prefetch overhead for small packets (<= 256B).
When forwarding packets with XDP, a packet that is smaller
than a certain size (set to ~256 bytes) would be sent inline within
its WQE TX descrptor (mem-copied), when the hardware tx queue is congested
beyond a pre-defined water-mark.
This is added to better utilize the HW resources (which now makes
one less packet data prefetch) and allow better scalability, on the
account of CPU usage (which now 'memcpy's the packet into the WQE).
To load balance between HW and CPU and get max packet rate, we use
watermarks to detect how much the HW is congested and move the work
loads back and forth between HW and CPU.
Performance:
Tested packet rate for UDP 64Byte multi-stream
over two dual port ConnectX-5 100Gbps NICs.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
* Tested with hyper-threading disabled
XDP_TX:
| | before | after | |
| 24 rings | 51Mpps | 116Mpps | +126% |
| 1 ring | 12Mpps | 12Mpps | same |
XDP_REDIRECT:
** Below is the transmit rate, not the redirection rate
which might be larger, and is not affected by this patch.
| | before | after | |
| 32 rings | 64Mpps | 92Mpps | +43% |
| 1 ring | 6.4Mpps | 6.4Mpps | same |
As we can see, feature significantly improves scaling, without
hurting single ring performance.
Tariq Toukan [Wed, 27 Feb 2019 10:06:08 +0000 (12:06 +0200)]
net/mlx5e: RX, Support multiple outstanding UMR posts
The buffers mapping of the Multi-Packet WQEs (of Striding RQ)
is done via UMR posts, one UMR WQE per an RX MPWQE.
A single MPWQE is capable of serving many incoming packets,
usually larger than the budget of a single napi cycle.
Hence, posting a single UMR WQE per napi cycle (and handling its
completion in the next cycle) works fine in many common cases,
but not always.
When an XDP program is loaded, every MPWQE is capable of serving less
packets, to satisfy the packet-per-page requirement.
Thus, for the same number of packets more MPWQEs (and UMR posts)
are needed (twice as much for the default MTU), giving less latency
room for the UMR completions.
In this patch, we add support for multiple outstanding UMR posts,
to allow faster gap closure between consuming MPWQEs and reposting
them back into the WQ.
For better SW and HW locality, we combine the UMR posts in bulks of
(at least) two.
This is expected to improve packet rate in high CPU scale.
Performance test:
As expected, huge improvement in large-scale (48 cores).
xdp_redirect_map, 64B UDP multi-stream.
Redirect from ConnectX-5 100Gbps to ConnectX-6 100Gbps.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz.
Before: Unstable, 7 to 30 Mpps
After: Stable, at 70.5 Mpps
====================
net: phy: mscc: Improvements to VSC8514 PHY driver.
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This patch series adds support for 10BASE-T, 100BASE-TX, and
1000BASE-T, QSGMII link with the MAC, downshifting, HP Auto-MDIX
detection and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all
PHYs in the package. So any modification in any register of this bank
affects all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
This patch series adds support for VSC8514 in Microsemi driver(mscc.c)
and removes support from Vitesse driver(vitesse.c).
v8
- mscc: Added appropriate code using phy_modify() in vsc8514_config_init().
v7
- mscc: Handled return values in vsc8514_config_init().
v6
- mscc: Added proper return value in vsc85xx_csr_ctrl_phy_read().
- mscc: Replaced __mdiobus_write and__mdiobus_read with __phy_write and __phy_read resp.
- mscc: Replaced register addresses in 8514_config_init() with proper constants.
v5
- mscc: Added return error statements for few function calls.
- mscc: Added comments in vsc85xx_csr_ctrl_phy_read() and vsc85xx_csr_ctrl_phy_write()
v4
- mscc: Removed features settings
- mscc: Removed aneg_done settings.
v3
- mscc: Used BIT(x) for PHY_MCB_S6G_WRITE and PHY_MCB_S6G_READ
instead of hex.
- mscc: Replaced magic numbers with proper constants.
- mscc: Handled delays and timeouts at appropriate points.
- mscc: Added comments/explanation where requested.
v2
- mscc: Sorted variable declarations in reverse christmas tree order.
v1
- Added 0/2 file.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8514 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X, can communicate with the MAC via QSGMII.
The MAC interface protocol for each port within QSGMII can
be either 1000BASE-X or SGMII, if the QSGMII MAC that the VSC8514 is
connecting to supports this functionality.
VSC8514 also supports SGMII MAC-side autonegotiation on each individual
port, downshifting, can set the blinking pattern of each of its 4 LEDs,
SyncE, 1000BASE-T Ring Resiliency as well as HP Auto-MDIX detection.
This adds support for 10BASE-T, 100BASE-TX, and 1000BASE-T,
QSGMII link with the MAC, downshifting, HP Auto-MDIX detection
and blinking pattern for its 4 LEDs.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.
Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com> Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Gomez [Mon, 22 Apr 2019 19:08:04 +0000 (21:08 +0200)]
spi: ST ST95HF NFC: declare missing of table
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Gomez [Mon, 22 Apr 2019 19:08:03 +0000 (21:08 +0200)]
spi: Micrel eth switch: declare missing of table
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: phy: marvell: add new default led configure for m88e151x
The default m88e151x LED configuration is 0x1177, used LED[0]
for 1000M link, LED[1] for 100M link, and LED[2] for active.
But for some boards, which use LED[0] for link, and LED[1] for
active, prefer to be 0x1040. To be compatible with this case,
this patch defines a new dev_flag, and set it before connect
phy in HNS3 driver. When phy initializing, using the new
LED configuration if this dev_flag is set.
Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Bluetooth: hci_bcm: Fix empty regulator supplies for Intel Macs
The code path for Macs goes through bcm_apple_get_resources(), which
skips over the code that sets up the regulator supplies. As a result,
the call to regulator_bulk_enable() / regulator_bulk_disable() results
in a NULL pointer dereference.
This was reported on the kernel.org Bugzilla, bug 202963.
Unbreak Broadcom Bluetooth support on Intel Macs by checking if the
supplies were set up before enabling or disabling them.
The same does not need to be done for the clocks, as the common clock
framework API checks for NULL pointers.
Fixes: 75d11676dccb ("Bluetooth: hci_bcm: Add support for regulator supplies") Cc: <stable@vger.kernel.org> # 5.0.x Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: Fix incorrect pointer arithmatic in ext_adv_report_evt
In ext_adv_report_event rssi comes before data (not after data as
in legacy adv_report_evt) so "+ 1" is not required in the ptr arithmatic
to point to next report.
Dan Carpenter [Wed, 3 Apr 2019 05:34:16 +0000 (08:34 +0300)]
6lowpan: Off by one handling ->nexthdr
NEXTHDR_MAX is 255. What happens here is that we take a u8 value
"hdr->nexthdr" from the network and then look it up in
lowpan_nexthdr_nhcs[]. The problem is that if hdr->nexthdr is 0xff then
we read one element beyond the end of the array so the array needs to
be one element larger.
Fixes: 92aa7c65d295 ("6lowpan: add generic nhc layer interface") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Acked-by: Alexander Aring <aring@mojatatu.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Bluetooth: btbcm: Add default address for BCM43341B
The BCM43341B has the default MAC address 43:34:1B:00:1F:AC if none
is given. This address was found when enabling Bluetooth on multiple
Intel Edison modules. It also contains the sequence 43341B, the name
the chip identifies itself as. Using the same BD_ADDR is problematic
when having multiple Intel Edison modules in each others range.
The default address also has the LAA (locally administered address)
bit set which prevents a BNEP device from being created, needed for
BT tethering.
Add this to the list of black listed default MAC addresses and let
the user configure a valid one using f.i.
`btmgmt -i hci0 public-addr xx:xx:xx:xx:xx:xx`
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ferry Toth <ftoth@exalondelft.nl> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Young Xiao [Fri, 12 Apr 2019 07:24:30 +0000 (15:24 +0800)]
Bluetooth: hidp: fix buffer overflow
Struct ca is copied from userspace. It is not checked whether the "name"
field is NULL terminated, which allows local users to obtain potentially
sensitive information from kernel stack memory, via a HIDPCONNADD command.
This vulnerability is similar to CVE-2011-1079.
Signed-off-by: Young Xiao <YangX92@hotmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
Tamás Szűcs [Sun, 14 Apr 2019 18:38:14 +0000 (20:38 +0200)]
Bluetooth: btmrvl: add support for SD8987 chipset
This patch adds support for Marvell 88W8987 chipset with SDIO interface.
Register offsets and supported feature flags are updated. The corresponding
firmware image file shall be "mrvl/sd8987_uapsta.bin".
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Thu, 18 Apr 2019 09:08:02 +0000 (17:08 +0800)]
Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth
Add runtime PM support to btmtksdio. With this way, there will be the
benefit of the device entering the more power saving state once it is
been a while data traffic is idle.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Tue, 5 Mar 2019 00:14:25 +0000 (08:14 +0800)]
Bluetooth: mediatek: Fixed incorrect type in assignment
Fixed warning: incorrect type in assignment reported by kbuild test robot.
The detailed warning is shown as below.
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
All warnings (new ones prefixed by >>):
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
sparse warnings: (new ones prefixed by >>)
btmtkuart.c:671:18: sparse: warning: incorrect type in assignment
(different base types)
btmtkuart.c:671:18: sparse: expected unsigned int [usertype] baudrate
btmtkuart.c:671:18: sparse: got restricted __le32 [usertype]
vim +671 drivers/bluetooth/btmtkuart.c
659
660 static int btmtkuart_change_baudrate(struct hci_dev *hdev)
661 {
662 struct btmtkuart_dev *bdev = hci_get_drvdata(hdev);
663 struct btmtk_hci_wmt_params wmt_params;
664 u32 baudrate;
665 u8 param;
666 int err;
667
668 /* Indicate the device to enter the probe state the host is
669 * ready to change a new baudrate.
670 */
> 671 baudrate = cpu_to_le32(bdev->desired_speed);
672 wmt_params.op = MTK_WMT_HIF;
Fixes: 22eaf6c9946a ("Bluetooth: mediatek: add support for MediaTek MT7663U and MT7668U UART devices") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Mon, 18 Mar 2019 20:58:33 +0000 (04:58 +0800)]
Bluetooth: btmtksdio: fix uninitialized symbol errors in btmtksdio_rx_packet
Fixed all the below warnings. They would probably cause the following
error handling path would use the uninitialized value and then produce
unexpected behavior.
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_len’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:376:15: note: ‘old_len’ was declared here
unsigned int old_len;
^~~~~~~
drivers/bluetooth/btmtksdio.c:470:2: warning: ‘old_data’ may be used
uninitialized in this function [-Wmaybe-uninitialized]
print_hex_dump(KERN_ERR, "err sdio rx: ", DUMP_PREFIX_NONE, 4, 1,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
old_data, old_len, true);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtksdio.c:375:17: note: ‘old_data’ was declared here
unsigned char *old_data;
^~~~~~~~
v2: Remove old_len and old_data because the error path for sdio_readsb also
seems wrong. And change the prefix from "mediatek" to "btmtksdio".
Fixes: d74eef2834b5 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:02:00 +0000 (05:02 +0800)]
Bluetooth: btsdio: Use module_sdio_driver helper
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:01:59 +0000 (05:01 +0800)]
Bluetooth: mediatek: Use module_sdio_driver helper
Macro module_sdio_driver is used for drivers whose init and exit paths
only register and unregister to SDIO API. So remove boilerplate code to
make code simpler by using module_sdio_driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Wed, 13 Mar 2019 21:01:58 +0000 (05:01 +0800)]
mmc: sdio: Add helper macro for sdio_driver boilerplate
This patch introduces the module_sdio_driver macro which is a convenience
macro for SDIO driver modules similar to module_usb_driver. It is intended
to be used by drivers which init/exit section does nothing but register/
unregister the SDIO driver. By using this macro it is possible to eliminate
a few lines of boilerplate code per SDIO driver.
Suggested-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
l2cap_le_flowctl_init was reseting the tx_credits which works only for
outgoing connection since that set the tx_credits on the response, for
incoming connections that was not the case which leaves the channel
without any credits causing it to be suspended.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org # 4.20+
Bluetooth: hci_qca: Add helper function to get the chip family
Many functions obtain a 'struct qca_serdev' only to read the btsoc_type
field. Add a helper function that encapsulates this.
This also fixes crashes observed on platforms with ROME controllers
that are instantiated through ldisc and not as serdev clients. The
crashes are caused by NULL pointer dereferentiations, which stem from
the driver's assumption that a QCA HCI device is always associated with
a serdev device.
Fixes: fa9ad876b8e0 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990") Reported-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Sean Wang [Fri, 8 Mar 2019 01:15:44 +0000 (09:15 +0800)]
Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices
This adds the support of enabling MT7663S and MT7668S SDIO-based
Bluetooth function.
There are quite many differences between MT766[3,8]S and standard
Bluetooth SDIO devices such as Type-A and Type-B devices. For example,
MT766[3,8]S have its own SDIO registers layout, definition, SDIO packet
format, and the specific flow should be programmed on them to complete
the device initialization and low power control and so on.
Currently, there are many independent programming sequences from the
transport which are exactly the same as the ones in btusb.c about MediaTek
support [1] and btmtkuart.c. We can try to split the transport independent
Bluetooth setups on the advance, place them into the common files and allow
varous transport drivers to reuse them in the future.
Sean Wang [Fri, 8 Mar 2019 01:15:43 +0000 (09:15 +0800)]
mmc: add SDIO identifiers for MediaTek Bluetooth devices
The SDIO identifier for MediaTek Bluetooth devices were defined in the
MediaTek Bluetooth driver. Moving the definitions in MMC header file
seems common sense.
Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
All we do is write the length/status and address bits to a DMA
descriptor only to write its contents into on-chip registers right
after, eliminate this unnecessary step.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bridge: Fix possible use-after-free when deleting bridge port
When a bridge port is being deleted, do not dereference it later in
br_vlan_port_event() as it can result in a use-after-free [1] if the RCU
callback was executed before invoking the function.
[ 130.146195] Freed by task 0:
[ 130.149421] __kasan_slab_free+0x125/0x170
[ 130.154016] kfree+0xf3/0x310
[ 130.157349] kobject_put+0x1a8/0x4c0
[ 130.161363] rcu_core+0x859/0x19b0
[ 130.165175] __do_softirq+0x250/0xa26
[ 130.170956] The buggy address belongs to the object at ffff8881e4aa1ae8
which belongs to the cache kmalloc-1k of size 1024
[ 130.184972] The buggy address is located 0 bytes inside of
1024-byte region [ffff8881e4aa1ae8, ffff8881e4aa1ee8)
Fixes: 9c0ec2e7182a ("bridge: support binding vlan dev link state to vlan member bridge ports") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Cc: Mike Manning <mmanning@vyatta.att-mail.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by: Mike Manning <mmanning@vyatta.att-mail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
r8152: sync sa_family with the media type of network device
Without this patch the socket address family sporadically gets wrong
value ends up the dev_set_mac_address() fails to set the desired MAC
address.
Fixes: 25766271e42f ("r8152: Refresh MAC address during USBDEVFS_RESET") Signed-off-by: Crag.Wang <crag.wang@dell.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-By: Mario Limonciello <mario.limonciello@dell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset includes two improvements with regards to shared buffer
configuration in mlxsw.
The first part of this patchset forbids the user from performing illegal
shared buffer configuration that can result in unnecessary packet loss.
In order to better communicate these configuration failures to the user,
extack is propagated from devlink towards drivers. This is done in
patches #1-#8.
The second part of the patchset deals with the shared buffer
configuration of the CPU port. When a packet is trapped by the device,
it is sent across the PCI bus to the attached host CPU. From the
device's perspective, it is as if the packet is transmitted through the
CPU port.
While testing traffic directed at the CPU it became apparent that for
certain packet sizes and certain burst sizes, the current shared buffer
configuration of the CPU port is inadequate and results in packet drops.
The configuration is adjusted by patches #9-#14 that create two new pools
- ingress & egress - which are dedicated for CPU traffic.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_buffers: Adjust CPU port shared buffer egress quotas
Switch the CPU port to use the new dedicated egress pool instead the
previously used egress pool which was shared with normal front panel
ports.
Add per-port quotas for the amount of traffic that can be buffered for
the CPU port and also adjust the per-{port, TC} quotas.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw: spectrum_buffers: Allow skipping ingress port quota configuration
The CPU port is used to transmit traffic that is trapped to the host
CPU. It is therefore irrelevant to define ingress quota for it.
Add a 'skip_ingress' argument to the function tasked with configuring
per-port quotas, so that ingress quotas could be skipped in case the
passed local port is the CPU port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>