Gil Adam [Sun, 16 Jun 2019 10:18:28 +0000 (13:18 +0300)]
iwlwifi: support per-platform antenna gain
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: mvm: remove check for lq_sta in __iwl_mvm_rs_tx_status()
The check is not necessary anymore, because now the struct is not
allocated separately, but is part of the mvmsta struct. Remove the
check, since it's dead code.
iwlwifi: mvm: simplify the channel switch flow for newer firmware
Any firmware that supports the new channel switch flow is
able to close / re-open the queues when needed. It takes
into account the channel switch mode etc...
Don't open / close the queues or enable / disable beacon
abort before and after the channel switch in case the
firmware is able to do this by itself.
iwlwifi: stop passing bogus gfp flags arguments to dma_alloc_coherent
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: dbg_ini: remove periphery phy and aux regions handling
periphery phy and aux regions should not be collected like periphery mac
region. Remove their handling. The handling will be added in the future
once the FW will support it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Fixes: 7a14c23dcdee ("iwlwifi: dbg: dump data according to the new ini TLVs") Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: dbg_ini: use linked list to store debug TLVs
Use a linked list to maintain the debug TLVs instead of a single buffer.
This way, the driver does not need to iterate over the binary file twice
and allocates smaller chunks of memory. Also, in case one allocation
fails the driver will work with the partial configuration instead of
aborting the entire debug configuration.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: dbg_ini: maintain buffer allocations from trans instead of TLVs buffer
Maintain DRAM debug buffer status in trans instead of keeping it as
part of the TLVs buffer to avoid allocating extra space for it.
Needed for future changes.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This means:
1) stop calling pm_runtime_resume when starting the hardware
2) removing the unneeded low_power parameter to start / stop hw / fw
transport ops
3) squashing transport functions that are now the same
_iwl_trans_pcie_start_hw / iwl_trans_pcie_start_hw
Alex Malamud [Mon, 10 Jun 2019 12:19:23 +0000 (15:19 +0300)]
iwlwifi: Set w-pointer upon resume according to SN
During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes Berg [Tue, 11 Jun 2019 13:38:13 +0000 (15:38 +0200)]
iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL
It doesn't make sense to use the FW thermal monitoring only if we
have CONFIG_THERMAL, because then we use the default thresholds
etc. which may be different from what the firmware implements, as
we don't maintain them in the driver now. Only the CTDP code needs
to actually be under CONFIG_THERMAL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alex Malamud [Wed, 22 May 2019 10:49:18 +0000 (13:49 +0300)]
iwlwifi: LTR updates
New FW versions introduces LTR feature enablement by default.
For such FW versions, driver (mvm/xvt) should not send
host command to enable LTR feature, also it should be possible to
override LTR configuration through the debugfs.
1. Send LTR feature enablement command only for FW versions
which does not advertises SET_LTR_GEN2 capability.
2. Implement ltr_config file in debugfs for LTR configuration override.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
This flag should never be set unless integration work with the
platform is done. We don't support any platforms officially and don't
plan to do so in the near future, so we can remove this option
entirely in order to avoid having it enabled by mistake.
This has been marked with "depends on EXPERT", so there shouldn't be
many systems running with it set. And, if there are systems, they
should not be using this flag.
For runtime PM to work with d0i3 code, a lot of integration work needs
to be done with the platform (e.g. the out-of-band wake up interrupt)
and we currently don't have any platforms where this integration
happened. So, this code has been pretty much stale for a while and
when someone enables it, it just breaks things.
Therefore, to simplify the code base and make sure no one enables this
by mistake, we will remove the whole code.
This is only the very start, much more work is needed.
Remove the places where we check iwl_mvm_is_d0i3_supported
but leave all the refs, those will be removed in a different
patch.
iwlwifi: dbg: move debug recording stop from trans to op mode
The op mode should stop the debug recording and not the transport layer.
Rename iwl_fwrt_stop_device into iwl_fw_dbg_stop_sync and move the debug
stop recording to it.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: dbg: move monitor recording functionality from header file
The recording functions are quite big to be inline and the driver should
expose only the stop and restart functions that are allowed to be used
rather then the internal helper functions. Move the functions from the
header file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi: mvm: remove redundant condition in iwl_mvm_set_hw_rfkill_state
If mvm->fwrt.cur_fw_img != IWL_UCODE_INIT, then
rfkill_safe_init_done must be true since
rfkill_safe_init_done is set to true before we start to load
the runtime image.
Remove the redundant condition.
Ilia Lin [Tue, 14 May 2019 14:19:06 +0000 (17:19 +0300)]
iwlwifi: Send DQA enable command only if TVL is on
The newer targets don't support the DQA enablement command
and will return error status, while older targets need it.
The feature is defined by the corresponding TLV.
Send the command only if the TLV is enabled.
Signed-off-by: Ilia Lin <ilia.lin@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Kalle Valo [Fri, 6 Sep 2019 08:59:32 +0000 (11:59 +0300)]
Merge tag 'mt76-for-kvalo-2019-09-05' of https://github.com/nbd168/wireless
mt76 patches for 5.4
* beacon tx fix for mt76x02
* sparse/checkpatch warning fixes
* DFS pattern detector for mt7615 (DFS channels not enabled yet)
* CSA support for mt7615
* mt7615 cleanup/fixes
* mt7615 rate control improvements
* usb fixes
* mt7615 powersave buffering fix
* new device support for mt76x0
* support for more ciphers in mt7615
* watchdog time fixes
* smart carrier sense on mt7615
* survey support on mt7615
* multiple interfaces on mt76x02u
* calibration data fix for mt7615
* fix for sending BAR after disassoc
mt76: mt7615: add support to read temperature from mcu
Introduce debugfs entry to read device temperature and related cmu
command. Introduce mt7615_mcu_parse_response to parse mcu response
messages and refactor mt7615_mcu_msg_send routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 22 Aug 2019 08:08:56 +0000 (10:08 +0200)]
mt76: remove offchannel check in tx scheduling
tx queues are already disabled by mac80211 during scanning or other
off-channel activity. There is no need to repeat the check in mt76,
since scheduled queues are selected by mac80211 as well.
Signed-off-by: Balakrishna Bandi <b.balakrishna@globaledgesoft.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 21 Aug 2019 13:21:00 +0000 (15:21 +0200)]
mt76: mt7615: apply calibration-free data from OTP
MT7615 chips usually come pre-calibrated, even when used on embedded boards.
In that case, the on-flash EEPROM data needs to be merged with some data
from OTP ROM.
Run this merge if the external EEPROM data is valid and OTP has valid fields.
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Wed, 21 Aug 2019 08:00:19 +0000 (10:00 +0200)]
mt76: add default implementation for mt76_sw_scan/mt76_sw_scan_complete
Introduce a default implementation for mt76_sw_scan and
mt76_sw_scan_complete in mt76 module and remove duplicated code
since most of the drivers share the same implementation
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Tue, 20 Aug 2019 14:56:25 +0000 (16:56 +0200)]
mt76: mt7615: add BIP_CMAC_128 cipher support
Refactor mt7615_mac_wtbl_set_key and introduce
the following routines in order to configure wtbl entries
and properly add hw support to BIP_CMAC_128 cipher:
- mt7615_mac_wtbl_update_cipher
- mt7615_mac_wtbl_update_pk
- mt7615_mac_wtbl_update_key
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76{15,03}_tx_tasklet in mt76_alloc_device in order to be used as
default tx_tasklet initialization. Remove duplicated code in
mt7603/mt7615 drivers
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable multi-interface support for mt76x02u driver. For the moment
allow max two concurrent interfaces in order to preserve enough room
for ps traffic since we are using beacon slots for it.
I have successfully tested the following configuration:
- AP + STA
- AP0 + AP1
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Tested-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76: mt76x02: do not copy beacon skb in mt76x02_mac_set_beacon_enable
Do not copy beacon skb in mt76x02_mac_set_beacon_enable for usb devices
since it will be done in mt76x02_update_beacon_iter. Moreover squash
mt76x02_mac_set_beacon_enable and __mt76x02_mac_set_beacon_enable since
the latter is run just by mt76x02_mac_set_beacon_enable
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sun, 28 Jul 2019 19:03:17 +0000 (21:03 +0200)]
mt76: mt7615: rework locking scheme for mt7615_set_channel
As already done for mt7603 driver, move mt76.mutex lock inside
mt7615_set_channel since we need to grab mt76.mutex in mt7615_mac_work.
This is a preliminary patch to add Smart Carrier Sense (SCS) support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ryder Lee [Wed, 24 Jul 2019 08:58:18 +0000 (16:58 +0800)]
mt76: mt76x02: fix some checkpatch warnings
This fixes the following checkpatch warnings:
ERROR: code indent should use tabs where possible
CHECK: Alignment should match open parenthesis
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Avoid precedence issues in macro
WARNING: Statements should start on a tabstop
WARNING: Unnecessary space before function pointer arguments
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Thu, 18 Jul 2019 22:50:42 +0000 (00:50 +0200)]
mt76: mt7603: fix watchdog rescheduling in mt7603_set_channel
Convert MT7603_WATCHDOG_TIME in jiffies rescheduling watchdog delayed
work
Fixes: c8846e101502 ("mt76: add driver for MT7603E and MT7628/7688") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sat, 13 Jul 2019 15:09:06 +0000 (17:09 +0200)]
mt76: introduce mt76_mmio_read_copy routine
Add mt76_mmio_read_copy routine and the related function pointer in
mt76_bus_ops data structure. mt76_mmio_read_copy will be used to add
BIP_CMAC_128 cipher hw support to mt7615 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Lorenzo Bianconi [Sat, 13 Jul 2019 15:09:05 +0000 (17:09 +0200)]
mt76: mt7615: add set_key_cmd and mt76_wcid to mt7615_mac_wtbl_set_key signature
Introduce set_key_cmd and mt76_wcid pointer to mt7615_mac_wtbl_set_key
signature and do not set key to NULL if cmd is DISABLE_KEY.
This is a preliminary patch to add BIP_CMAC_128 hw support to mt7615
driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add mt7615_mac_wtbl_set_key routine to configure wtbl key parameter
directly from host cpu. This is a preliminary patch to add BIP_CMAC_128
hw support. Moreover add static qualifier to mt7615_mac_get_key_info
routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
In contrast to mt76_wr() which we use to program registers,
on mt76_wr_copy() we should not change endian of the data.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer") Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Thu, 11 Jul 2019 19:17:06 +0000 (21:17 +0200)]
mt76: mt7615: fix using VHT STBC rates
The hardware expects MT_TX_RATE_NSS to be filled with the number of
space/time streams. For non-STBC rates, this is equal to nss.
For 1-stream STBC, this needs to be set to 2.
This is relevant for VHT rates only, on HT, the value is derived from MCS
internally.
Fix typo setting urb->transfer_buffer_length in mt76u_fill_rx_sg
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer") Fixes: f8f527b16db5 ("mt76: usb: use EP max packet aligned buffer sizes for rx") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Wed, 3 Jul 2019 19:39:04 +0000 (21:39 +0200)]
mt76: mt7615: sync with mt7603 rate control changes
- Store the previous and current rate set in the driver + the TSF value
at the time of the switch.
- Use the tx status TSF value to determine which rate set needs to be used
as reference.
- Report only short or long GI rates for a single status event, not a mix.
- The hardware reports the last used rate index. Use it along with the
retry count to figure out what rate was used for the first attempt.
- Use the same retry count value for all rate slots to make this calculation
work.
- Derive the probe rate from the current rateset instead of the skb cb
- Do not wait for a status report for the probe frame before removing the
probe rate from the rate table. Do it immediately after it was referenced
in a tx status report.
- Use the first half of the first rate retry budget for the probe rate
in order to avoid using too many retries on that rate
- Switch from lower rates to higher rates more conservatively
- enable hardware rate up/down selection
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>