Add support for operation modes 1-3 of the ADC128D818 (see datasheet sec.
8.4.1). These differ in the number and type of the available input signals,
requiring the driver to selectively hide sysfs nodes according to the
operation mode configured via devicetree.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net> Acked-by: Michael Hornung <mhornung.linux@gmail.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Alexander Koch [Fri, 6 Jan 2017 10:38:15 +0000 (11:38 +0100)]
hwmon: (adc128d818) Implement mode selection via dt
Implement operation mode selection using the optional 'ti,mode' devicetree
property (see [1]). The ADC128D818 supports four operation modes differing
in the number and type of input readings (see datasheet, sec. 8.4.1), of
which mode 0 is the default.
We only add handling of the 'ti,mode' property here, the driver still
supports nothing else than the default mode 0.
Add bindings documentation for the ADC128D818 driver, featuring default I2C
properties along with the optional 'mode' property for chip operation mode
selection (see datasheet, sec. 8.4.1).
Signed-off-by: Alexander Koch <mail@alexanderkoch.net> Acked-by: Michael Hornung <mhornung.linux@gmail.com> Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed whitespace error] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon: (tmp401) use smb word operations instead of 2 smb byte operations
tmp401 separately read/wrote high and low bytes of temperature values while
the hardware supports reading/writing those values in one operation. Driver
has been modified to use word operations where possible.
Tested with a tmp432 sensor on a mips64 platform.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck [Tue, 27 Dec 2016 22:15:07 +0000 (14:15 -0800)]
hwmon: (gl520sm) Fix overflows and crash seen when writing into limit attributes
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
Guenter Roeck [Tue, 27 Dec 2016 22:15:05 +0000 (14:15 -0800)]
hwmon: (dme1737) Fix overflows seen when writing into limit attributes
Writes into voltage limit, temperature limit, temperature hysteresis,
and temperature zone attributes can overflow due to unclamped parameters
to multiplications, additions, and subtractions.
Julia Lawall [Thu, 22 Dec 2016 12:05:35 +0000 (13:05 +0100)]
hwmon: (tmp401) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:34 +0000 (13:05 +0100)]
hwmon: (fam15h_power) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:33 +0000 (13:05 +0100)]
hwmon: (adt7475) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:32 +0000 (13:05 +0100)]
hwmon: (lm95234) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:31 +0000 (13:05 +0100)]
hwmon: (max6650) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:30 +0000 (13:05 +0100)]
hwmon: (emc2103) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:29 +0000 (13:05 +0100)]
hwmon: (lm83) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:28 +0000 (13:05 +0100)]
hwmon: (adm1025) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:27 +0000 (13:05 +0100)]
hwmon: (k8temp) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:26 +0000 (13:05 +0100)]
hwmon: (sch5627) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:25 +0000 (13:05 +0100)]
hwmon: (lm78) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:24 +0000 (13:05 +0100)]
hwmon: (pc87360) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:23 +0000 (13:05 +0100)]
hwmon: (nct6775) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:22 +0000 (13:05 +0100)]
hwmon: (lm90) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:21 +0000 (13:05 +0100)]
hwmon: (it87) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:20 +0000 (13:05 +0100)]
hwmon: (dme1737) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:19 +0000 (13:05 +0100)]
hwmon: (k10temp) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:18 +0000 (13:05 +0100)]
hwmon: (vt8231) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:17 +0000 (13:05 +0100)]
hwmon: (w83793) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:16 +0000 (13:05 +0100)]
hwmon: (f71805f) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:15 +0000 (13:05 +0100)]
hwmon: (pc87427) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:14 +0000 (13:05 +0100)]
hwmon: (w83791d) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:13 +0000 (13:05 +0100)]
hwmon: (w83792d) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:12 +0000 (13:05 +0100)]
hwmon: (w83781d) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:11 +0000 (13:05 +0100)]
hwmon: (w83627hf) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:10 +0000 (13:05 +0100)]
hwmon: (w83627ehf) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:09 +0000 (13:05 +0100)]
hwmon: (via686a) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:08 +0000 (13:05 +0100)]
hwmon: (via-cputemp) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:07 +0000 (13:05 +0100)]
hwmon: (smsc47m192) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:06 +0000 (13:05 +0100)]
hwmon: (smsc47m1) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:05 +0000 (13:05 +0100)]
hwmon: (sis5595) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:04 +0000 (13:05 +0100)]
hwmon: (sht15) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:03 +0000 (13:05 +0100)]
hwmon: (pcf8591) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:02 +0000 (13:05 +0100)]
hwmon: (nsa320) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:01 +0000 (13:05 +0100)]
hwmon: (nct6683) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:05:00 +0000 (13:05 +0100)]
hwmon: (mcp3021) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:59 +0000 (13:04 +0100)]
hwmon: (mc13783-adc) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:58 +0000 (13:04 +0100)]
hwmon: (max197) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:57 +0000 (13:04 +0100)]
hwmon: (max1619) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:56 +0000 (13:04 +0100)]
hwmon: (max1111) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:55 +0000 (13:04 +0100)]
hwmon: (lm93) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:54 +0000 (13:04 +0100)]
hwmon: (lm92) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:53 +0000 (13:04 +0100)]
hwmon: (lm87) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:52 +0000 (13:04 +0100)]
hwmon: (lm85) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:51 +0000 (13:04 +0100)]
hwmon: (lm80) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:50 +0000 (13:04 +0100)]
hwmon: (lm70) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:49 +0000 (13:04 +0100)]
hwmon: (lm63) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:48 +0000 (13:04 +0100)]
hwmon: (jz4740) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:47 +0000 (13:04 +0100)]
hwmon: (i5k_amb) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:46 +0000 (13:04 +0100)]
hwmon: (i5500_temp) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:45 +0000 (13:04 +0100)]
hwmon: (core) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:44 +0000 (13:04 +0100)]
hwmon: (gpio-fan) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:43 +0000 (13:04 +0100)]
hwmon: (gl520sm) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:42 +0000 (13:04 +0100)]
hwmon: (g762) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:41 +0000 (13:04 +0100)]
hwmon: (g760a) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:40 +0000 (13:04 +0100)]
hwmon: (fschmd) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:39 +0000 (13:04 +0100)]
hwmon: (f71882fg) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:38 +0000 (13:04 +0100)]
hwmon: (ds1621) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:37 +0000 (13:04 +0100)]
hwmon: (atxp1) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:36 +0000 (13:04 +0100)]
hwmon: (asb100) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:35 +0000 (13:04 +0100)]
hwmon: (adt7x10) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:34 +0000 (13:04 +0100)]
hwmon: (adt7470) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:33 +0000 (13:04 +0100)]
hwmon: (adm9240) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:32 +0000 (13:04 +0100)]
hwmon: (adm1031) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Julia Lawall [Thu, 22 Dec 2016 12:04:31 +0000 (13:04 +0100)]
hwmon: (adm1026) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Julia Lawall [Thu, 22 Dec 2016 12:04:30 +0000 (13:04 +0100)]
hwmon: (adm1021) use permission-specific DEVICE_ATTR variants
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Michael Walle [Thu, 15 Dec 2016 17:38:17 +0000 (18:38 +0100)]
hwmon: (adt7411) add min, max and alarm attributes
This patch adds support for the min, max and alarm attributes of the
voltage and temperature channels. Additionally, the temp2_fault attribute
is supported which indicates a fault of the external temperature diode.
Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Michael Walle [Mon, 2 Jan 2017 16:53:39 +0000 (17:53 +0100)]
hwmon: (lm90) fix temp1_max_alarm attribute
Since commit commit eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon
registration API") the temp1_max_alarm and temp1_crit_alarm attributes are
mapped to the same alarm bit. Fix the typo.
Fixes: eb1c8f4325d5 ("hwmon: (lm90) Convert to use new hwmon registration API") Signed-off-by: Micehael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Linus Torvalds [Sun, 1 Jan 2017 20:27:05 +0000 (12:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
Linus Torvalds [Fri, 30 Dec 2016 17:32:26 +0000 (09:32 -0800)]
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Olof Johansson [Thu, 29 Dec 2016 22:16:07 +0000 (14:16 -0800)]
mm/filemap: fix parameters to test_bit()
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes: b91e1302ad9b ('mm: optimize PageWaiters bit use for unlock_page()') Signed-off-by: Olof Johansson <olof@lixom.net> Brown-paper-bag-by: Linus Torvalds <dummy@duh.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 27 Dec 2016 19:40:38 +0000 (11:40 -0800)]
mm: optimize PageWaiters bit use for unlock_page()
In commit 62906027091f ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Bob Peterson <rpeterso@redhat.com> Cc: Steven Whitehouse <swhiteho@redhat.com> Cc: Andrew Lutomirski <luto@kernel.org> Cc: Andreas Gruenbacher <agruenba@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
John Brooks [Fri, 23 Dec 2016 00:53:10 +0000 (00:53 +0000)]
docs: Fix build failure
The 80211.tmpl DocBook file was removed in commit 819bf593767c ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb03b7 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org Signed-off-by: John Brooks <john@fastquake.com> Mea-culpa-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com> Acked-By: Joao Pinto <jpinto@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: John Fastabend <john.r.fastabend@intel.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 26 Dec 2016 16:31:27 +0000 (08:31 -0800)]
openvswitch: upcall: Fix vlan handling.
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes: 5108bbaddc ("openvswitch: add processing of L3 packets"). CC: Jarno Rajahalme <jarno@ovn.org> CC: Jiri Benc <jbenc@redhat.com> Signed-off-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 25 Dec 2016 06:33:16 +0000 (14:33 +0800)]
ipv4: Namespaceify tcp_tw_reuse knob
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org> Fixes: d7db7a882deb ("crypto: acomp - update testmgr with support for acomp") Signed-off-by: Laura Abbott <labbott@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jan Kara [Fri, 21 Oct 2016 09:33:49 +0000 (11:33 +0200)]
ext4: Simplify DAX fault path
Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:34:31 +0000 (14:34 +0200)]
dax: Call ->iomap_begin without entry lock during dax fault
Currently ->iomap_begin() handler is called with entry lock held. If the
filesystem held any locks between ->iomap_begin() and ->iomap_end()
(such as ext4 which will want to hold transaction open), this would cause
lock inversion with the iomap_apply() from standard IO path which first
calls ->iomap_begin() and only then calls ->actor() callback which grabs
entry locks for DAX (if it faults when copying from/to user provided
buffers).
Fix the problem by nesting grabbing of entry lock inside ->iomap_begin()
- ->iomap_end() pair.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:48:38 +0000 (14:48 +0200)]
dax: Finish fault completely when loading holes
The only case when we do not finish the page fault completely is when we
are loading hole pages into a radix tree. Avoid this special case and
finish the fault in that case as well inside the DAX fault handler. It
will allow us for easier iomap handling.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:10:28 +0000 (17:10 +0200)]
dax: Avoid page invalidation races and unnecessary radix tree traversals
Currently dax_iomap_rw() takes care of invalidating page tables and
evicting hole pages from the radix tree when write(2) to the file
happens. This invalidation is only necessary when there is some block
allocation resulting from write(2). Furthermore in current place the
invalidation is racy wrt page fault instantiating a hole page just after
we have invalidated it.
So perform the page invalidation inside dax_iomap_actor() where we can
do it only when really necessary and after blocks have been allocated so
nobody will be instantiating new hole pages anymore.
Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:22:44 +0000 (17:22 +0200)]
mm: Invalidate DAX radix tree entries only if appropriate
Currently invalidate_inode_pages2_range() and invalidate_mapping_pages()
just delete all exceptional radix tree entries they find. For DAX this
is not desirable as we track cache dirtiness in these entries and when
they are evicted, we may not flush caches although it is necessary. This
can for example manifest when we write to the same block both via mmap
and via write(2) (to different offsets) and fsync(2) then does not
properly flush CPU caches when modification via write(2) was the last
one.
Create appropriate DAX functions to handle invalidation of DAX entries
for invalidate_inode_pages2_range() and invalidate_mapping_pages() and
wire them up into the corresponding mm functions.
Acked-by: Johannes Weiner <hannes@cmpxchg.org> Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 14:42:53 +0000 (16:42 +0200)]
ext2: Return BH_New buffers for zeroed blocks
So far we did not return BH_New buffers from ext2_get_blocks() when we
allocated and zeroed-out a block for DAX inode to avoid racy zeroing in
DAX code. This zeroing is gone these days so we can remove the
workaround.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com>