Intel PCONFIG targets are enumerated via new CPUID leaf 0x1b. This patch
detects all supported targets of PCONFIG and implements helper to check
if the target is supported.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Kai Huang <kai.huang@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180305162610.37510-5-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/tme: Detect if TME and MKTME is activated by BIOS
IA32_TME_ACTIVATE MSR (0x982) can be used to check if BIOS has enabled
TME and MKTME. It includes which encryption policy/algorithm is selected
for TME or available for MKTME. For MKTME, the MSR also enumerates how
many KeyIDs are available.
We would need to exclude KeyID bits from physical address bits.
detect_tme() would adjust cpuinfo_x86::x86_phys_bits accordingly.
We have to do this even if we are not going to use KeyID bits
ourself. VM guests still have to know that these bits are not usable
for physical address.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Kai Huang <kai.huang@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180305162610.37510-3-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/boot/compressed/64: Handle 5-level paging boot if kernel is above 4G
This patch addresses a shortcoming in current boot process on machines
that supports 5-level paging.
If a bootloader enables 64-bit mode with 4-level paging, we might need to
switch over to 5-level paging. The switching requires the disabling
paging. It works fine if kernel itself is loaded below 4G.
But if the bootloader put the kernel above 4G (not sure if anybody does
this), we would lose control as soon as paging is disabled, because the
code becomes unreachable to the CPU.
This patch implements a trampoline in lower memory to handle this
situation.
We only need the memory for a very short time, until the main kernel
image sets up own page tables.
We go through the trampoline even if we don't have to: if we're already
in 5-level paging mode or if we don't need to switch to it. This way the
trampoline gets tested on every boot.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180312100246.89175-5-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/boot/compressed/64: Use page table in trampoline memory
If a bootloader enables 64-bit mode with 4-level paging, we might need to
switch over to 5-level paging. The switching requires the disabling
paging. It works fine if kernel itself is loaded below 4G.
But if the bootloader put the kernel above 4G (i.e. in kexec() case),
we would lose control as soon as paging is disabled, because the code
becomes unreachable to the CPU.
To handle the situation, we need a trampoline in lower memory that would
take care of switching on 5-level paging.
Apart from the trampoline code itself we also need a place to store
top-level page table in lower memory as we don't have a way to load
64-bit values into CR3 in 32-bit mode. We only really need 8 bytes there
as we only use the very first entry of the page table. But we allocate a
whole page anyway.
This patch switches 32-bit code to use page table in trampoline memory.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180312100246.89175-4-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/boot/compressed/64: Make sure we have a 32-bit code segment
When kernel starts in 64-bit mode we inherit the GDT from the bootloader.
It may cause a problem if the GDT doesn't have a 32-bit code segment
where we expect it to be.
Load our own GDT with known segments.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Borislav Petkov <bp@suse.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180312100246.89175-2-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/mm: Do not use paravirtualized calls in native_set_p4d()
In 4-level paging mode, native_set_p4d() updates the entry in the top-level
page table. With PTI, update to the top-level kernel page table requires
update to the userspace copy of the table as well, using pti_set_user_pgd().
native_set_p4d() uses p4d_val() and pgd_val() to convert types between
p4d_t and pgd_t.
p4d_val() and pgd_val() are paravirtualized and we must not use them in
native helpers, as they crash the boot in paravirtualized environments.
Replace p4d_val() and pgd_val() with native_p4d_val() and
native_pgd_val() in native_set_p4d().
Reported-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 91f606a8fa68 ("x86/mm: Replace compile-time checks for 5-level paging with runtime-time checks") Link: http://lkml.kernel.org/r/20180305081641.4290-1-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/boot/compressed/64: Prepare new top-level page table for trampoline
If trampoline code would need to switch between 4- and 5-level paging
modes, we have to use a page table in trampoline memory.
Having it in trampoline memory guarantees that it's below 4G and we can
point CR3 to it from 32-bit trampoline code.
We only use the page table if the desired paging mode doesn't match the
mode we are in. Otherwise the page table is unused and trampoline code
wouldn't touch CR3.
For 4- to 5-level paging transition, we set up current (4-level paging)
CR3 as the first and the only entry in a new top-level page table.
For 5- to 4-level paging transition, copy page table pointed by first
entry in the current top-level page table as our new top-level page
table.
If the page table is used by trampoline we would need to copy it to new
page table outside trampoline and update CR3 before restoring trampoline
memory.
Tested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180226180451.86788-6-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/boot/compressed/64: Find a place for 32-bit trampoline
If a bootloader enables 64-bit mode with 4-level paging, we might need to
switch over to 5-level paging. The switching requires the disabling of
paging, which works fine if kernel itself is loaded below 4G.
But if the bootloader puts the kernel above 4G (not sure if anybody does
this), we would lose control as soon as paging is disabled, because the
code becomes unreachable to the CPU.
To handle the situation, we need a trampoline in lower memory that would
take care of switching on 5-level paging.
This patch finds a spot in low memory for a trampoline.
The heuristic is based on code in reserve_bios_regions().
We find the end of low memory based on BIOS and EBDA start addresses.
The trampoline is put just before end of low memory. It's mimic approach
taken to allocate memory for realtime trampoline.
Tested-by: Borislav Petkov <bp@suse.de> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180226180451.86788-3-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/kprobes: Fix kernel crash when probing .entry_trampoline code
Disable the kprobe probing of the entry trampoline:
.entry_trampoline is a code area that is used to ensure page table
isolation between userspace and kernelspace.
At the beginning of the execution of the trampoline, we load the
kernel's CR3 register. This has the effect of enabling the translation
of the kernel virtual addresses to physical addresses. Before this
happens most kernel addresses can not be translated because the running
process' CR3 is still used.
If a kprobe is placed on the trampoline code before that change of the
CR3 register happens the kernel crashes because int3 handling pages are
not accessible.
To fix this, add the .entry_trampoline section to the kprobe blacklist
to prohibit the probing of code before all the kernel pages are
accessible.
Signed-off-by: Francis Deslauriers <francis.deslauriers@efficios.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: mathieu.desnoyers@efficios.com Cc: mhiramat@kernel.org Link: http://lkml.kernel.org/r/1520565492-4637-2-git-send-email-francis.deslauriers@efficios.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Ashok Raj [Wed, 28 Feb 2018 10:28:46 +0000 (11:28 +0100)]
x86/microcode: Synchronize late microcode loading
Original idea by Ashok, completely rewritten by Borislav.
Before you read any further: the early loading method is still the
preferred one and you should always do that. The following patch is
improving the late loading mechanism for long running jobs and cloud use
cases.
Gather all cores and serialize the microcode update on them by doing it
one-by-one to make the late update process as reliable as possible and
avoid potential issues caused by the microcode update.
[ Borislav: Rewrite completely. ]
Co-developed-by: Borislav Petkov <bp@suse.de> Signed-off-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-8-bp@alien8.de
Borislav Petkov [Wed, 28 Feb 2018 10:28:45 +0000 (11:28 +0100)]
x86/microcode: Request microcode on the BSP
... so that any newer version can land in the cache and can later be
fished out by the application functions. Do that before grabbing the
hotplug lock.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-7-bp@alien8.de
Borislav Petkov [Wed, 28 Feb 2018 10:28:44 +0000 (11:28 +0100)]
x86/microcode/intel: Look into the patch cache first
The cache might contain a newer patch - look in there first.
A follow-on change will make sure newest patches are loaded into the
cache of microcode patches.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-6-bp@alien8.de
Ashok Raj [Wed, 28 Feb 2018 10:28:43 +0000 (11:28 +0100)]
x86/microcode: Do not upload microcode if CPUs are offline
Avoid loading microcode if any of the CPUs are offline, and issue a
warning. Having different microcode revisions on the system at any time
is outright dangerous.
Ashok Raj [Wed, 28 Feb 2018 10:28:42 +0000 (11:28 +0100)]
x86/microcode/intel: Writeback and invalidate caches before updating microcode
Updating microcode is less error prone when caches have been flushed and
depending on what exactly the microcode is updating. For example, some
of the issues around certain Broadwell parts can be addressed by doing a
full cache flush.
[ Borislav: Massage it and use native_wbinvd() in both cases. ]
Ashok Raj [Wed, 28 Feb 2018 10:28:41 +0000 (11:28 +0100)]
x86/microcode/intel: Check microcode revision before updating sibling threads
After updating microcode on one of the threads of a core, the other
thread sibling automatically gets the update since the microcode
resources on a hyperthreaded core are shared between the two threads.
Check the microcode revision on the CPU before performing a microcode
update and thus save us the WRMSR 0x79 because it is a particularly
expensive operation.
Borislav Petkov [Wed, 28 Feb 2018 10:28:40 +0000 (11:28 +0100)]
x86/microcode: Get rid of struct apply_microcode_ctx
It is a useless remnant from earlier times. Use the ucode_state enum
directly.
No functional change.
Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Tom Lendacky <thomas.lendacky@amd.com> Tested-by: Ashok Raj <ashok.raj@intel.com> Cc: Arjan Van De Ven <arjan.van.de.ven@intel.com> Link: https://lkml.kernel.org/r/20180228102846.13447-2-bp@alien8.de
x86/spectre_v2: Don't check microcode versions when running under hypervisors
As:
1) It's known that hypervisors lie about the environment anyhow (host
mismatch)
2) Even if the hypervisor (Xen, KVM, VMWare, etc) provided a valid
"correct" value, it all gets to be very murky when migration happens
(do you provide the "new" microcode of the machine?).
And in reality the cloud vendors are the ones that should make sure that
the microcode that is running is correct and we should just sing lalalala
and trust them.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Wanpeng Li <kernellwp@gmail.com> Cc: kvm <kvm@vger.kernel.org> Cc: Krčmář <rkrcmar@redhat.com> Cc: Borislav Petkov <bp@alien8.de> CC: "H. Peter Anvin" <hpa@zytor.com> CC: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180226213019.GE9497@char.us.oracle.com
Andy Lutomirski [Wed, 7 Mar 2018 19:12:27 +0000 (11:12 -0800)]
x86/vsyscall/64: Drop "native" vsyscalls
Since Linux v3.2, vsyscalls have been deprecated and slow. From v3.2
on, Linux had three vsyscall modes: "native", "emulate", and "none".
"emulate" is the default. All known user programs work correctly in
emulate mode, but vsyscalls turn into page faults and are emulated.
This is very slow. In "native" mode, the vsyscall page is easily
usable as an exploit gadget, but vsyscalls are a bit faster -- they
turn into normal syscalls. (This is in contrast to vDSO functions,
which can be much faster than syscalls.) In "none" mode, there are
no vsyscalls.
For all practical purposes, "native" was really just a chicken bit
in case something went wrong with the emulation. It's been over six
years, and nothing has gone wrong. Delete it.
Josh Poimboeuf [Tue, 6 Mar 2018 23:58:15 +0000 (17:58 -0600)]
objtool: Fix 32-bit build
Fix the objtool build when cross-compiling a 64-bit kernel on a 32-bit
host. This also simplifies read_retpoline_hints() a bit and makes its
implementation similar to most of the other annotation reading
functions.
Reported-by: Sven Joachim <svenjoac@gmx.de> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: b5bc2231b8ad ("objtool: Add retpoline validation") Link: http://lkml.kernel.org/r/2ca46c636c23aa9c9d57d53c75de4ee3ddf7a7df.1520380691.git.jpoimboe@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Gleixner [Wed, 28 Feb 2018 20:14:26 +0000 (21:14 +0100)]
x86/cpu_entry_area: Sync cpu_entry_area to initial_page_table
The separation of the cpu_entry_area from the fixmap missed the fact that
on 32bit non-PAE kernels the cpu_entry_area mapping might not be covered in
initial_page_table by the previous synchronizations.
This results in suspend/resume failures because 32bit utilizes initial page
table for resume. The absence of the cpu_entry_area mapping results in a
triple fault, aka. insta reboot.
With PAE enabled this works by chance because the PGD entry which covers
the fixmap and other parts incindentally provides the cpu_entry_area
mapping as well.
Synchronize the initial page table after setting up the cpu entry
area. Instead of adding yet another copy of the same code, move it to a
function and invoke it from the various places.
It needs to be investigated if the existing calls in setup_arch() and
setup_per_cpu_areas() can be replaced by the later invocation from
setup_cpu_entry_areas(), but that's beyond the scope of this fix.
Fixes: 92a0f81d8957 ("x86/cpu_entry_area: Move it out of the fixmap") Reported-by: Woody Suwalski <terraluna977@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Woody Suwalski <terraluna977@gmail.com> Cc: William Grant <william.grant@canonical.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802282137290.1392@nanos.tec.linutronix.de
Josh Poimboeuf [Wed, 28 Feb 2018 13:19:21 +0000 (07:19 -0600)]
objtool: Fix another switch table detection issue
Continue the switch table detection whack-a-mole. Add a check to
distinguish KASAN data reads from switch data reads. The switch jump
tables in .rodata have relocations associated with them.
This fixes the following warning:
crypto/asymmetric_keys/x509_cert_parser.o: warning: objtool: x509_note_pkey_algo()+0xa4: sibling call from callable instruction with modified stack frame
Juergen Gross [Mon, 26 Feb 2018 14:08:18 +0000 (15:08 +0100)]
x86/xen: Zero MSR_IA32_SPEC_CTRL before suspend
Older Xen versions (4.5 and before) might have problems migrating pv
guests with MSR_IA32_SPEC_CTRL having a non-zero value. So before
suspending zero that MSR and restore it after being resumed.
Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Jan Beulich <jbeulich@suse.com> Cc: stable@vger.kernel.org Cc: xen-devel@lists.xenproject.org Cc: boris.ostrovsky@oracle.com Link: https://lkml.kernel.org/r/20180226140818.4849-1-jgross@suse.com
Tom Lendacky [Mon, 26 Feb 2018 23:25:54 +0000 (17:25 -0600)]
x86/mm/sme: Disable stack protection for mem_encrypt_identity.c
Stack protection is not compatible with early boot code. All of the early
SME boot code is now isolated in a separate file, mem_encrypt_identity.c,
so arch/x86/mm/Makefile can be updated to turn off stack protection for
the entire file. This eliminates the need to worry about other functions
within the file being instrumented with stack protection (as was seen
when a newer version of GCC instrumented sme_encrypt_kernel() where an
older version hadn't). It also allows removal of the __nostackprotector
attribute from individual functions.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Borislav Petkov <bp@suse.de> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Link: https://lkml.kernel.org/r/20180226232554.14108.16881.stgit@tlendack-t1.amdoffice.net
x86/boot/e820: Implement a range manipulation operator
Add a more versatile memmap= operator, which -- in addition to all the
things that were possible before -- allows you to:
- redeclare existing ranges -- before, you were limited to adding ranges;
- drop any range -- like a mem= for any location;
- use any e820 memory type -- not just some predefined ones.
The syntax is:
memmap=<size>%<offset>-<oldtype>+<newtype>
Size and offset work as usual. The "-<oldtype>" and "+<newtype>" are
optional and their existence determine the behavior: The command
works on the specified range of memory limited to type <oldtype>
(if specified). This memory is then configured to show up as <newtype>.
If <newtype> is not specified, the memory is removed from the e820 map.
Signed-off-by: Jan H. Schönherr <jschoenh@amazon.de> Cc: Andy Lutomirski <luto@kernel.org> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20180202231020.15608-1-jschoenh@amazon.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jan Beulich [Fri, 23 Feb 2018 08:27:37 +0000 (01:27 -0700)]
x86/mm: Consider effective protection attributes in W+X check
Using just the leaf page table entry flags would cause a false warning
in case _PAGE_RW is clear or _PAGE_NX is set in a higher level entry.
Hand through both the current entry's flags as well as the accumulated
effective value (the latter as pgprotval_t instead of pgprot_t, as it's
not an actual entry's value).
This in particular eliminates the false W+X warning when running under
Xen, as commit:
had to make the necessary adjustment in L2 rather than L1 (the reason is
explained there). I.e. _PAGE_RW is clear there in L1, but _PAGE_NX is
set in L2.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/5A8FDE8902000078001AABBB@prv-mh.provo.novell.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Juergen Gross [Mon, 19 Feb 2018 10:09:06 +0000 (11:09 +0100)]
x86/xen: Add pvh specific rsdp address retrieval function
Add pvh_get_root_pointer() for Xen PVH guests to communicate the
address of the RSDP table given to the kernel via Xen start info.
This makes the kernel boot again in PVH mode after on recent Xen the
RSDP was moved to higher addresses. So up to that change it was pure
luck that the legacy method to locate the RSDP was working when
running as PVH mode.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: boris.ostrovsky@oracle.com Cc: lenb@kernel.org Cc: linux-acpi@vger.kernel.org Cc: xen-devel@lists.xenproject.org Link: http://lkml.kernel.org/r/20180219100906.14265-4-jgross@suse.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Juergen Gross [Mon, 19 Feb 2018 10:09:04 +0000 (11:09 +0100)]
acpi: Introduce acpi_arch_get_root_pointer() for getting rsdp address
Add an architecture specific function to get the address of the RSDP
table. Per default it will just return 0 indicating falling back to
the current mechanism.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Eric Biederman <ebiederm@xmission.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: boris.ostrovsky@oracle.com Cc: lenb@kernel.org Cc: linux-acpi@vger.kernel.org Cc: xen-devel@lists.xenproject.org Link: http://lkml.kernel.org/r/20180219100906.14265-2-jgross@suse.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Linus Torvalds [Mon, 26 Feb 2018 01:02:24 +0000 (17:02 -0800)]
Merge tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa
Pull Xtensa fixes from Max Filippov:
"Two fixes for reserved memory/DMA buffers allocation in high memory on
xtensa architecture
- fix memory accounting when reserved memory is in high memory region
- fix DMA allocation from high memory"
* tag 'xtensa-20180225' of git://github.com/jcmvbkbc/linux-xtensa:
xtensa: support DMA buffers in high memory
xtensa: fix high memory/reserved memory collision
Linus Torvalds [Mon, 26 Feb 2018 00:58:55 +0000 (16:58 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes:
- UAPI data type correction for hyperv
- correct the cpu cores field in /proc/cpuinfo on CPU hotplug
- return proper error code in the resctrl file system failure path to
avoid silent subsequent failures
- correct a subtle accounting issue in the new vector allocation code
which went unnoticed for a while and caused suspend/resume
failures"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations
x86/topology: Fix function name in documentation
x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
x86/apic/vector: Handle vector release on CPU unplug correctly
genirq/matrix: Handle CPU offlining proper
x86/headers/UAPI: Use __u64 instead of u64 in <uapi/asm/hyperv.h>
Linus Torvalds [Mon, 26 Feb 2018 00:29:59 +0000 (16:29 -0800)]
Merge branch 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"Three patches to fix memory ordering issues on ALPHA and a comment to
clarify the usage scope of a mutex internal function"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()
locking/mutex: Add comment to __mutex_owner() to deter usage
Linus Torvalds [Sun, 25 Feb 2018 21:43:18 +0000 (13:43 -0800)]
Merge tag 'nfs-for-4.16-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- fix a broken cast in nfs4_callback_recallany()
- fix an Oops during NFSv4 migration events
- make struct nlmclnt_fl_close_lock_ops static
* tag 'nfs-for-4.16-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: make struct nlmclnt_fl_close_lock_ops static
nfs: system crashes after NFS4ERR_MOVED recovery
NFSv4: Fix broken cast in nfs4_callback_recallany()
Linus Torvalds [Sun, 25 Feb 2018 00:05:50 +0000 (16:05 -0800)]
Merge tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Add handling for a missing instruction in our 32-bit BPF JIT so that
it can be used for seccomp filtering.
- Add a missing NULL pointer check before a function call in new EEH
code.
- Fix an error path in the new ocxl driver to correctly return EFAULT.
- The support for the new ibm,drc-info device tree property turns out
to need several fixes, so for now we just stop advertising to
firmware that we support it until the bugs can be ironed out.
- One fix for the new drmem code which was incorrectly modifying the
device tree in place.
- Finally two fixes for the RFI flush support, so that firmware can
advertise to us that it should be disabled entirely so as not to
affect performance.
Thanks to: Bharata B Rao, Frederic Barrat, Juan J. Alvarez, Mark Lord,
Michael Bringmann.
* tag 'powerpc-4.16-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv: Support firmware disable of RFI flush
powerpc/pseries: Support firmware disable of RFI flush
powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2
powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access
powerpc/pseries: Revert support for ibm,drc-info devtree property
powerpc/pseries: Fix duplicate firmware feature for DRC_INFO
ocxl: Fix potential bad errno on irq allocation
powerpc/eeh: Fix crashes in eeh_report_resume()
1) Fix TTL offset calculation in mac80211 mesh code, from Peter Oh.
2) Fix races with procfs in ipt_CLUSTERIP, from Cong Wang.
3) Memory leak fix in lpm_trie BPF map code, from Yonghong Song.
4) Need to use GFP_ATOMIC in BPF cpumap allocations, from Jason Wang.
5) Fix potential deadlocks in netfilter getsockopt() code paths, from
Paolo Abeni.
6) Netfilter stackpointer size checks really are needed to validate
user input, from Florian Westphal.
7) Missing timer init in x_tables, from Paolo Abeni.
8) Don't use WQ_MEM_RECLAIM in mac80211 hwsim, from Johannes Berg.
9) When an ibmvnic device is brought down then back up again, it can be
sent queue entries from a previous session, handle this properly
instead of crashing. From Thomas Falcon.
10) Fix TCP checksum on LRO buffers in mlx5e, from Gal Pressman.
11) When we are dumping filters in cls_api, the output SKB is empty, and
the filter we are dumping is too large for the space in the SKB, we
should return -EMSGSIZE like other netlink dump operations do.
Otherwise userland has no signal that is needs to increase the size
of its read buffer. From Roman Kapl.
12) Several XDP fixes for virtio_net, from Jesper Dangaard Brouer.
13) Module refcount leak in netlink when a dump start fails, from Jason
Donenfeld.
14) Handle sub-optimal GSO sizes better in TCP BBR congestion control,
from Eric Dumazet.
15) Releasing bpf per-cpu arraymaps can take a long time, add a
condtional scheduling point. From Eric Dumazet.
16) Implement retpolines for tail calls in x64 and arm64 bpf JITs. From
Daniel Borkmann.
17) Fix page leak in gianfar driver, from Andy Spencer.
18) Missed clearing of estimator scratch buffer, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net_sched: gen_estimator: fix broken estimators based on percpu stats
gianfar: simplify FCS handling and fix memory leak
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
macvlan: fix use-after-free in macvlan_common_newlink()
bpf, arm64: fix out of bounds access in tail call
bpf, x64: implement retpoline for tail call
rxrpc: Fix send in rxrpc_send_data_packet()
net: aquantia: Fix error handling in aq_pci_probe()
bpf: fix rcu lockdep warning for lpm_trie map_free callback
bpf: add schedule points in percpu arrays management
regulatory: add NUL to request alpha2
ibmvnic: Fix early release of login buffer
net/smc9194: Remove bogus CONFIG_MAC reference
net: ipv4: Set addr_type in hash_keys for forwarded case
tcp_bbr: better deal with suboptimal GSO
smsc75xx: fix smsc75xx_set_features()
netlink: put module reference if dump start fails
selftests/bpf/test_maps: exit child process without error in ENOMEM case
selftests/bpf: update gitignore with test_libbpf_open
selftests/bpf: tcpbpf_kern: use in6_* macros from glibc
..
Linus Torvalds [Fri, 23 Feb 2018 23:04:24 +0000 (15:04 -0800)]
Merge branch 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem fixes from James Morris:
- keys fixes via David Howells:
"A collection of fixes for Linux keyrings, mostly thanks to Eric
Biggers:
- Fix some PKCS#7 verification issues.
- Fix handling of unsupported crypto in X.509.
- Fix too-large allocation in big_key"
- Seccomp updates via Kees Cook:
"These are fixes for the get_metadata interface that landed during
-rc1. While the new selftest is strictly not a bug fix, I think
it's in the same spirit of avoiding bugs"
- an IMA build fix from Randy Dunlap
* 'fixes-v4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
integrity/security: fix digsig.c build error with header file
KEYS: Use individual pages in big_key for crypto buffers
X.509: fix NULL dereference when restricting key with unsupported_sig
X.509: fix BUG_ON() when hash algorithm is unsupported
PKCS#7: fix direct verification of SignerInfo signature
PKCS#7: fix certificate blacklisting
PKCS#7: fix certificate chain verification
seccomp: add a selftest for get_metadata
ptrace, seccomp: tweak get_metadata behavior slightly
seccomp, ptrace: switch get_metadata types to arch independent
Linus Torvalds [Fri, 23 Feb 2018 22:59:29 +0000 (14:59 -0800)]
Merge tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS fix from James Hogan:
"A single MIPS fix for mismatching struct compat_flock, resulting in
bus errors starting Firefox on Debian 8 since 4.13"
* tag 'mips_fixes_4.16_3' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips:
MIPS: Drop spurious __unused in struct compat_flock
Linus Torvalds [Fri, 23 Feb 2018 22:41:14 +0000 (14:41 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two bugfixes, one v4.16 regression fix, and two documentation fixes"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: designware: Consider SCL GPIO optional
i2c: busses: i2c-sirf: Fix spelling: "formular" -> "formula".
i2c: bcm2835: Set up the rising/falling edge delays
i2c: i801: Add missing documentation entries for Braswell and Kaby Lake
i2c: designware: must wait for enable
Linus Torvalds [Fri, 23 Feb 2018 22:09:43 +0000 (14:09 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are mostly fixes for problems with merge window code.
In addition we have one doc update (alua) and two dead code removals
(aiclib and octogon) a spurious assignment removal (csiostor) and a
performance improvement for storvsc involving better interrupt
spreading and increasing the command per lun handling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla4xxx: skip error recovery in case of register disconnect.
scsi: aacraid: fix shutdown crash when init fails
scsi: qedi: Cleanup local str variable
scsi: qedi: Fix truncation of CHAP name and secret
scsi: qla2xxx: Fix incorrect handle for abort IOCB
scsi: qla2xxx: Fix double free bug after firmware timeout
scsi: storvsc: Increase cmd_per_lun for higher speed devices
scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
scsi: scsi_dh: Document alua_rtpg_queue() arguments
scsi: Remove Makefile entry for oktagon files
scsi: aic7xxx: remove aiclib.c
scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
scsi: sym53c8xx_2: iterator underflow in sym_getsync()
scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
scsi: csiostor: remove redundant assignment to pointer 'ln'
scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
scsi: qla2xxx: Fix memory corruption during hba reset test
scsi: mpt3sas: fix an out of bound write
Linus Torvalds [Fri, 23 Feb 2018 18:31:31 +0000 (10:31 -0800)]
Merge tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of fixes for rc3:
Exynos:
- fixes for using monotonic timestamps
- register definitions
- removal of unused file
ipu-v3L
- minor changes
- make some register arrays const+static
- fix some leaks
meson:
- fix for vsync
atomic:
- fix for memory leak
EDID parser:
- add quirks for some more non-desktop devices
- 6-bit panel fix.
drm_mm:
- fix a bug in the core drm mm hole handling
cirrus:
- fix lut loading regression
Lastly there is a deadlock fix around runtime suspend for secondary
GPUs.
There was a deadlock between one thread trying to wait for a workqueue
job to finish in the runtime suspend path, and the workqueue job it
was waiting for in turn waiting for a runtime_get_sync to return.
The fixes avoids it by not doing the runtime sync in the workqueue as
then we always wait for all those tasks to complete before we runtime
suspend"
* tag 'drm-fixes-for-v4.16-rc3' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm/tve200: fix kernel-doc documentation comment include
drm/edid: quirk Sony PlayStation VR headset as non-desktop
drm/edid: quirk Windows Mixed Reality headsets as non-desktop
drm/edid: quirk Oculus Rift headsets as non-desktop
drm/meson: fix vsync buffer update
drm: Handle unexpected holes in color-eviction
drm: exynos: Use proper macro definition for HDMI_I2S_PIN_SEL_1
drm/exynos: remove exynos_drm_rotator.h
drm/exynos: g2d: Delete an error message for a failed memory allocation in two functions
drm/exynos: fix comparison to bitshift when dealing with a mask
drm/exynos: g2d: use monotonic timestamps
drm/edid: Add 6 bpc quirk for CPT panel in Asus UX303LA
gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
drm/amdgpu: Fix deadlock on runtime suspend
drm/radeon: Fix deadlock on runtime suspend
drm/nouveau: Fix deadlock on runtime suspend
drm: Allow determining if current task is output poll worker
...
Eric Dumazet [Fri, 23 Feb 2018 03:45:27 +0000 (19:45 -0800)]
net_sched: gen_estimator: fix broken estimators based on percpu stats
pfifo_fast got percpu stats lately, uncovering a bug I introduced last
year in linux-4.10.
I missed the fact that we have to clear our temporary storage
before calling __gnet_stats_copy_basic() in the case of percpu stats.
Without this fix, rate estimators (tc qd replace dev xxx root est 1sec
4sec pfifo_fast) are utterly broken.
Fixes: 1c0d32fde5bd ("net_sched: gen_estimator: complete rewrite of rate estimators") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Spencer [Thu, 22 Feb 2018 19:05:33 +0000 (11:05 -0800)]
gianfar: simplify FCS handling and fix memory leak
Previously, buffer descriptors containing only the frame check sequence
(FCS) were skipped and not added to the skb. However, the page reference
count was still incremented, leading to a memory leak.
Fixing this inside gfar_add_rx_frag() is difficult due to reserved
memory handling and page reuse. Instead, move the FCS handling to
gfar_process_frame() and trim off the FCS before passing the skb up the
networking stack.
Signed-off-by: Andy Spencer <aspencer@spacex.com> Signed-off-by: Jim Gruen <jgruen@spacex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Thu, 22 Feb 2018 15:55:34 +0000 (16:55 +0100)]
ipv6 sit: work around bogus gcc-8 -Wrestrict warning
gcc-8 has a new warning that detects overlapping input and output arguments
in memcpy(). It triggers for sit_init_net() calling ipip6_tunnel_clone_6rd(),
which is actually correct:
net/ipv6/sit.c: In function 'sit_init_net':
net/ipv6/sit.c:192:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
The problem here is that the logic detecting the memcpy() arguments finds them
to be the same, but the conditional that tests for the input and output of
ipip6_tunnel_clone_6rd() to be identical is not a compile-time constant.
We know that netdev_priv(t->dev) is the same as t for a tunnel device,
and comparing "dev" directly here lets the compiler figure out as well
that 'dev == sitn->fb_tunnel_dev' when called from sit_init_net(), so
it no longer warns.
This code is old, so Cc stable to make sure that we don't get the warning
for older kernels built with new gcc.
Commit d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:
* for macvlan it always returns NULL because 'lowerdev' is the one that
was used to register rx handler (port) in macvlan_port_create() as
well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
its own rx handler before macvlan_common_newlink().
Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free") Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Pratyush Anand [Mon, 5 Feb 2018 13:28:01 +0000 (14:28 +0100)]
arm64: fix unwind_frame() for filtered out fn for function graph tracing
do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).
Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.
Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().
This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.
Andrea Parri [Thu, 22 Feb 2018 09:24:48 +0000 (10:24 +0100)]
locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs
Successful RMW operations are supposed to be fully ordered, but
Alpha's xchg() and cmpxchg() do not meet this requirement.
Will Deacon noticed the bug:
> So MP using xchg:
>
> WRITE_ONCE(x, 1)
> xchg(y, 1)
>
> smp_load_acquire(y) == 1
> READ_ONCE(x) == 0
>
> would be allowed.
... which thus violates the above requirement.
Fix it by adding a leading smp_mb() to the xchg() and cmpxchg() implementations.
Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrea Parri <parri.andrea@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-alpha@vger.kernel.org Link: http://lkml.kernel.org/r/1519291488-5752-1-git-send-email-parri.andrea@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Andrea Parri [Thu, 22 Feb 2018 09:24:29 +0000 (10:24 +0100)]
locking/xchg/alpha: Clean up barrier usage by using smp_mb() in place of __ASM__MB
Replace each occurrence of __ASM__MB with a (trailing) smp_mb() in
xchg(), cmpxchg(), and remove the now unused __ASM__MB definitions;
this improves readability, with no additional synchronization cost.
Suggested-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Andrea Parri <parri.andrea@gmail.com> Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Turner <mattst88@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Richard Henderson <rth@twiddle.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-alpha@vger.kernel.org Link: http://lkml.kernel.org/r/1519291469-5702-1-git-send-email-parri.andrea@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paolo Bonzini [Thu, 22 Feb 2018 15:43:18 +0000 (16:43 +0100)]
KVM/VMX: Optimize vmx_vcpu_run() and svm_vcpu_run() by marking the RDMSR path as unlikely()
vmx_vcpu_run() and svm_vcpu_run() are large functions, and giving
branch hints to the compiler can actually make a substantial cycle
difference by keeping the fast path contiguous in memory.
With this optimization, the retpoline-guest/retpoline-host case is
about 50 cycles faster.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: KarimAllah Ahmed <karahmed@amazon.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/20180222154318.20361-3-pbonzini@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Paolo Bonzini [Thu, 22 Feb 2018 15:43:17 +0000 (16:43 +0100)]
KVM/x86: Remove indirect MSR op calls from SPEC_CTRL
Having a paravirt indirect call in the IBRS restore path is not a
good idea, since we are trying to protect from speculative execution
of bogus indirect branch targets. It is also slower, so use
native_wrmsrl() on the vmentry path too.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Jim Mattson <jmattson@google.com> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: KarimAllah Ahmed <karahmed@amazon.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Radim Krčmář <rkrcmar@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Fixes: d28b387fb74da95d69d2615732f50cceb38e9a4d Link: http://lkml.kernel.org/r/20180222154318.20361-2-pbonzini@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Wang Hui [Fri, 23 Feb 2018 03:26:03 +0000 (19:26 -0800)]
x86/intel_rdt: Fix incorrect returned value when creating rdgroup sub-directory in resctrl file system
If no monitoring feature is detected because all monitoring features are
disabled during boot time or there is no monitoring feature in hardware,
creating rdtgroup sub-directory by "mkdir" command reports error:
mkdir: cannot create directory ‘/sys/fs/resctrl/p1’: No such file or directory
But the sub-directory actually is generated and content is correct:
cpus cpus_list schemata tasks
The error is because rdtgroup_mkdir_ctrl_mon() returns non zero value after
the sub-directory is created and the returned value is reported as an error
to user.
Clear the returned value to report to user that the sub-directory is
actually created successfully.
Signed-off-by: Wang Hui <john.wanghui@huawei.com> Signed-off-by: Zhang Yanfei <yanfei.zhang@huawei.com> Signed-off-by: Fenghua Yu <fenghua.yu@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi V Shankar <ravi.v.shankar@intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Luck <tony.luck@intel.com> Cc: Vikas <vikas.shivappa@intel.com> Cc: Xiaochen Shen <xiaochen.shen@intel.com> Link: http://lkml.kernel.org/r/1519356363-133085-1-git-send-email-fenghua.yu@intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Thomas Gleixner [Thu, 22 Feb 2018 11:08:06 +0000 (12:08 +0100)]
x86/apic/vector: Handle vector release on CPU unplug correctly
When a irq vector is replaced, then the previous vector is normally
released when the first interrupt happens on the new vector. If the target
CPU of the previous vector is already offline when the new vector is
installed, then the previous vector is silently discarded, which leads to
accounting issues causing suspend failures and other problems.
Adjust the logic so that the previous vector is freed in the underlying
matrix allocator to ensure that the accounting stays correct.
Fixes: 69cde0004a4b ("x86/vector: Use matrix allocator for vector assignment") Reported-by: Yuriy Vostrikov <delamonpansie@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Yuriy Vostrikov <delamonpansie@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180222112316.930791749@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org>
Bharata B Rao [Wed, 21 Feb 2018 10:36:26 +0000 (16:06 +0530)]
powerpc/mm/drmem: Fix unexpected flag value in ibm,dynamic-memory-v2
Memory addtion and removal by count and indexed-count methods
temporarily mark the LMBs that are being added/removed by a special
flag value DRMEM_LMB_RESERVED. Accessing flags value directly at a few
places without proper accessor method is causing two unexpected
side-effects:
- DRMEM_LMB_RESERVED bit is becoming part of the flags word of
drconf_cell_v2 entries in ibm,dynamic-memory-v2 DT property.
- This results in extra drconf_cell entries in ibm,dynamic-memory-v2.
For example if 1G memory is added, it leads to one entry for 3 LMBs
and 1 separate entry for the last LMB. All the 4 LMBs should be
defined by one entry here.
Fix this by always accessing the flags by its accessor method
drmem_lmb_flags().
Fixes: 2b31e3aec1db ("powerpc/drmem: Add support for ibm, dynamic-memory-v2 property") Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Dave Airlie [Fri, 23 Feb 2018 01:11:57 +0000 (11:11 +1000)]
Merge tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux into drm-fixes
drm/imx: ipu-v3 fixups and grayscale support
- Make const interrupt register arrays static, reduces object size.
- Fix device_node leaks in PRE/PRG phandle lookup functions.
- Add 8-bit and 16-bit grayscale buffer support to ipu_cpmem_set_image,
- add 10-bit and 12-bit grayscale media bus support to ipu-csi,
to be used by the imx-media driver.
* tag 'imx-drm-next-2018-02-22' of git://git.pengutronix.de/git/pza/linux:
gpu: ipu-csi: add 10/12-bit grayscale support to mbus_code_to_bus_cfg
gpu: ipu-cpmem: add 16-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: prg: fix device node leak in ipu_prg_lookup_by_phandle
gpu: ipu-v3: pre: fix device node leak in ipu_pre_lookup_by_phandle
gpu: ipu-cpmem: add 8-bit grayscale support to ipu_cpmem_set_image
gpu: ipu-v3: make const arrays int_reg static, shrinks object size
Kees Cook [Fri, 23 Feb 2018 00:59:26 +0000 (16:59 -0800)]
MIPS: boot: Define __ASSEMBLY__ for its.S build
The MIPS %.its.S compiler command did not define __ASSEMBLY__, which meant
when compiler_types.h was added to kconfig.h, unexpected things appeared
(e.g. struct declarations) which should not have been present. As done in
the general %.S compiler command, __ASSEMBLY__ is now included here too.
The failure was:
Error: arch/mips/boot/vmlinux.gz.its:201.1-2 syntax error
FATAL ERROR: Unable to parse input tree
/usr/bin/mkimage: Can't read arch/mips/boot/vmlinux.gz.itb.tmp: Invalid argument
/usr/bin/mkimage Can't add hashes to FIT blob
Reported-by: kbuild test robot <lkp@intel.com> Fixes: 28128c61e08e ("kconfig.h: Include compiler types to avoid missed struct attributes") Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann [Fri, 23 Feb 2018 00:03:43 +0000 (01:03 +0100)]
bpf, arm64: fix out of bounds access in tail call
I recently noticed a crash on arm64 when feeding a bogus index
into BPF tail call helper. The crash would not occur when the
interpreter is used, but only in case of JIT. Output looks as
follows:
In this case the index used in BPF r3 is the same as in r1
at the time of the call, meaning we fed a pointer as index;
here, it had the value 0xffff808fd7cf0500 which sits in x2.
While I found tail calls to be working in general (also for
hitting the error cases), I noticed the following in the code
emission:
Meaning, the tests passed because commit ddb55992b04d ("arm64:
bpf: implement bpf_tail_call() helper") was using signed compares
instead of unsigned which as a result had the test wrongly passing.
Change this but also the tail call count test both into unsigned
and cap the index as u32. Latter we did as well in 90caccdd8cc0
("bpf: fix bpf_tail_call() x64 JIT") and is needed in addition here,
too. Tested on HiSilicon Hi1616.
Daniel Borkmann [Thu, 22 Feb 2018 14:12:53 +0000 (15:12 +0100)]
bpf, x64: implement retpoline for tail call
Implement a retpoline [0] for the BPF tail call JIT'ing that converts
the indirect jump via jmp %rax that is used to make the long jump into
another JITed BPF image. Since this is subject to speculative execution,
we need to control the transient instruction sequence here as well
when CONFIG_RETPOLINE is set, and direct it into a pause + lfence loop.
The latter aligns also with what gcc / clang emits (e.g. [1]).
JIT dump after patch:
# bpftool p d x i 1
0: (18) r2 = map[id:1]
2: (b7) r3 = 0
3: (85) call bpf_tail_call#12
4: (b7) r0 = 2
5: (95) exit
Thomas Gleixner [Thu, 22 Feb 2018 11:08:05 +0000 (12:08 +0100)]
genirq/matrix: Handle CPU offlining proper
At CPU hotunplug the corresponding per cpu matrix allocator is shut down and
the allocated interrupt bits are discarded under the assumption that all
allocated bits have been either migrated away or shut down through the
managed interrupts mechanism.
This is not true because interrupts which are not started up might have a
vector allocated on the outgoing CPU. When the interrupt is started up
later or completely shutdown and freed then the allocated vector is handed
back, triggering warnings or causing accounting issues which result in
suspend failures and other issues.
Change the CPU hotplug mechanism of the matrix allocator so that the
remaining allocations at unplug time are preserved and global accounting at
hotplug is correctly readjusted to take the dormant vectors into account.
Randy Dunlap [Mon, 12 Feb 2018 21:18:38 +0000 (13:18 -0800)]
fs/signalfd: fix build error for BUS_MCEERR_AR
Fix build error in fs/signalfd.c by using same method that is used in
kernel/signal.c: separate blocks for different signal si_code values.
./fs/signalfd.c: error: 'BUS_MCEERR_AR' undeclared (first use in this function)
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
David Howells [Thu, 22 Feb 2018 14:38:14 +0000 (14:38 +0000)]
rxrpc: Fix send in rxrpc_send_data_packet()
All the kernel_sendmsg() calls in rxrpc_send_data_packet() need to send
both parts of the iov[] buffer, but one of them does not. Fix it so that
it does.
Without this, short IPv6 rxrpc DATA packets may be seen that have the rxrpc
header included, but no payload.
Fixes: 5a924b8951f8 ("rxrpc: Don't store the rxrpc header in the Tx queue sk_buffs") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Thu, 22 Feb 2018 09:11:55 +0000 (12:11 +0300)]
net: aquantia: Fix error handling in aq_pci_probe()
We should check "self->aq_hw" for allocation failure, and also we should
free it on the error paths.
Fixes: 23ee07ad3c2f ("net: aquantia: Cleanup pci functions module") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 22 Feb 2018 18:10:35 +0000 (10:10 -0800)]
bpf: fix rcu lockdep warning for lpm_trie map_free callback
Commit 9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function")
fixed a memory leak and removed unnecessary locks in map_free callback function.
Unfortrunately, it introduced a lockdep warning. When lockdep checking is turned on,
running tools/testing/selftests/bpf/test_lpm_map will have:
[ 98.294321] =============================
[ 98.294807] WARNING: suspicious RCU usage
[ 98.295359] 4.16.0-rc2+ #193 Not tainted
[ 98.295907] -----------------------------
[ 98.296486] /home/yhs/work/bpf/kernel/bpf/lpm_trie.c:572 suspicious rcu_dereference_check() usage!
[ 98.297657]
[ 98.297657] other info that might help us debug this:
[ 98.297657]
[ 98.298663]
[ 98.298663] rcu_scheduler_active = 2, debug_locks = 1
[ 98.299536] 2 locks held by kworker/2:1/54:
[ 98.300152] #0: ((wq_completion)"events"){+.+.}, at: [<00000000196bc1f0>] process_one_work+0x157/0x5c0
[ 98.301381] #1: ((work_completion)(&map->work)){+.+.}, at: [<00000000196bc1f0>] process_one_work+0x157/0x5c0
Since actual trie tree removal happens only after no other
accesses to the tree are possible, replacing
rcu_dereference_protected(*slot, lockdep_is_held(&trie->lock))
with
rcu_dereference_protected(*slot, 1)
fixed the issue.
Fixes: 9a3efb6b661f ("bpf: fix memory leak in lpm_trie map_free callback function") Reported-by: Eric Dumazet <edumazet@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yonghong Song <yhs@fb.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 22 Feb 2018 20:13:01 +0000 (12:13 -0800)]
Merge tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
Linus Torvalds [Thu, 22 Feb 2018 20:05:43 +0000 (12:05 -0800)]
Merge tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a small number of staging and iio driver fixes for 4.16-rc2.
The IIO fixes are all for reported things, and the android driver
fixes also resolve some reported problems. The remaining fsl-mc
Kconfig change resolves a build testing error that Arnd reported.
All of these have been in linux-next with no reported issues"
* tag 'staging-4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: buffer: check if a buffer has been set up when poll is called
iio: adis_lib: Initialize trigger before requesting interrupt
staging: android: ion: Zero CMA allocated memory
staging: android: ashmem: Fix a race condition in pin ioctls
staging: fsl-mc: fix build testing on x86
iio: srf08: fix link error "devm_iio_triggered_buffer_setup" undefined
staging: iio: ad5933: switch buffer mode to software
iio: adc: stm32: fix stm32h7_adc_enable error handling
staging: iio: adc: ad7192: fix external frequency setting
iio: adc: aspeed: Fix error handling path
Linus Torvalds [Thu, 22 Feb 2018 20:04:05 +0000 (12:04 -0800)]
Merge tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.16-rc3.
There are some binder driver fixes to resolve reported issues in
stress testing the recent binder changes, some extcon driver fixes,
and a few mei driver fixes and new device ids.
All of these, with the exception of the mei driver id additions, have
been in linux-next for a while. I forgot to push out the mei driver id
additions to kernel.org until today, but all build tests pass with
them enabled"
* tag 'char-misc-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: me: add cannon point device ids for 4th device
mei: me: add cannon point device ids
mei: set device client to the disconnected state upon suspend.
ANDROID: binder: synchronize_rcu() when using POLLFREE.
binder: replace "%p" with "%pK"
ANDROID: binder: remove WARN() for redundant txn error
binder: check for binder_thread allocation failure in binder_poll()
extcon: int3496: process id-pin first so that we start with the right status
Revert "extcon: axp288: Redo charger type detection a couple of seconds after probe()"
extcon: axp288: Constify the axp288_pwr_up_down_info array
Johannes Berg [Thu, 22 Feb 2018 19:55:28 +0000 (20:55 +0100)]
regulatory: add NUL to request alpha2
Similar to the ancient commit a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.