Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw: Fix eeprom offset for AR9287 devices (PCI/USB)
AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 24 Nov 2010 07:10:06 +0000 (08:10 +0100)]
mac80211: implement packet loss notification
For drivers that have accurate TX status reporting
we can report the number of consecutive lost packets
to userspace using the new cfg80211 CQM event. The
threshold is fixed right now, this may need to be
improved in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 24 Nov 2010 07:10:05 +0000 (08:10 +0100)]
cfg80211: allow using CQM event to notify packet loss
This adds the ability for drivers to use CQM events
to notify about packet loss for specific stations
(which could be the AP for the managed mode case).
Since the threshold might be determined by the
driver (it isn't passed in right now) it will be
passed out of the driver to userspace in the event.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Felix Fietkau <nbd@openwrt.org> Cc: Matt Smith <matt.smith@atheros.com> Cc: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should help with latency issues which can happen when
using aggregation.
Cc: Matt Smith <matt.smith@atheros.com> Cc: Senthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 23 Nov 2010 02:10:32 +0000 (03:10 +0100)]
mac80211: reduce the number of retries for nullfunc probing
Since nullfunc frames are transmitted as unicast frames, they're more
reliable than the broadcast probe requests, so we need fewer retries
to figure out whether the AP is really gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 23 Nov 2010 02:10:31 +0000 (03:10 +0100)]
mac80211: use nullfunc instead of probe request for connection monitoring
nullfunc frames are better for connection monitoring, because probe requests
are answered even if the AP has already dropped the connection, whereas
nullfunc frames from an unassociated station will trigger a disassoc/deauth
frame from the AP (WLAN_REASON_CLASS3_FRAME_FROM_NONASSOC_STA), which allows
the station to reconnect immediately instead of waiting until it attempts to
transmit the next unicast frame.
This only works on hardware with reliable tx ACK reporting, any other hardware
needs to fall back to the probe request method.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
- store the multicast rate as an index instead of the rate value
(reduces cpu overhead in a hotpath)
- validate the rate values (must match a bitrate in at least one sband)
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 23 Nov 2010 19:28:03 +0000 (20:28 +0100)]
mac80211: probe the AP when resuming
Check the connection by probing the AP (either using nullfunc or a
probe request). If nullfunc probing is supported and the assoc is no
longer valid, the AP will send a disassoc/deauth immediately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Fri, 19 Nov 2010 21:55:38 +0000 (22:55 +0100)]
mac80211: calculate beacon loss time accurately
Instead of using a fixed 2 second timeout, calculate beacon loss interval
from the advertised beacon interval and a frame count. With this beacon
loss happens after N (default 7) consecutive frames are missed which
for a typical setup (100TU beacon interval) is ~700ms (or ~1/3 previous).
Signed-off-by: Sam Leffler <sleffler@chromium.org> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Thu, 18 Nov 2010 12:27:57 +0000 (13:27 +0100)]
b43: N-PHY: fix values for PHY regs in channel tables of 2055 radio
Additional comment by Larry Finger <Larry.Finger@lwfinger.net>:
This change deserves a bit more explanation. You might include something like
"These tables came from reverse engineering the 5.10.56.46 version of the
Broadcom driver. Trace comparisons between b43 and the current Broadcom driver
(5.10.120.0) show byte reversals for the PHY register writes."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Paris [Tue, 23 Nov 2010 06:28:08 +0000 (06:28 +0000)]
SELinux: indicate fatal error in compat netfilter code
The SELinux ip postroute code indicates when policy rejected a packet and
passes the error back up the stack. The compat code does not. This patch
sends the same kind of error back up the stack in the compat code.
Based-on-patch-by: Paul Moore <paul.moore@hp.com> Signed-off-by: Eric Paris <eparis@redhat.com> Reviewed-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Paris [Tue, 23 Nov 2010 06:28:02 +0000 (06:28 +0000)]
SELinux: Only return netlink error when we know the return is fatal
Some of the SELinux netlink code returns a fatal error when the error might
actually be transient. This patch just silently drops packets on
potentially transient errors but continues to return a permanant error
indicator when the denial was because of policy.
Based-on-comments-by: Paul Moore <paul.moore@hp.com> Signed-off-by: Eric Paris <eparis@redhat.com> Reviewed-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Mon, 22 Nov 2010 14:39:39 +0000 (15:39 +0100)]
ath9k_hw: fix A-MPDU key search issues on AR9003
Under load, a large number of frames can produce decryption errors, even when
no key cache update is being done. Performing a key search for every single
frame in an A-MPDU improves reliability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Sun, 21 Nov 2010 02:39:01 +0000 (18:39 -0800)]
rt2x00: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.
text data bss dec hex filename
40197 56 8336 48589 bdcd drivers/net/wireless/rt2x00/rt2800lib.o.new
40205 56 8336 48597 bdd5 drivers/net/wireless/rt2x00/rt2800lib.o.old
Signed-off-by: Joe Perches <joe@perches.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 20 Nov 2010 02:08:46 +0000 (03:08 +0100)]
ath9k: fix recursive locking in the tx flush path
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Tested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 18 Nov 2010 20:08:10 +0000 (12:08 -0800)]
iwlwifi: fix modular 3945 only build
If only 3945 is selected, and is a module, build
fails because iwl-legacy.c won't be compiled. Fix
this by adding it to the build correctly.
This doesn't happen for 4965 because it is a bool
option, not tristate, since it's built into the
AGN module.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com> Tested-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 19 Nov 2010 07:11:01 +0000 (08:11 +0100)]
mac80211: Disable hw crypto for GTKs on AP VLAN interfaces
When using AP VLAN interfaces, each VLAN interface should be in its own
broadcast domain. Hostapd achieves this by assigning different GTKs to
different AP VLAN interfaces.
However, mac80211 drivers are not aware of AP VLAN interfaces and as
such mac80211 sends the GTK to the driver in the context of the base AP
mode interface. This causes problems when multiple AP VLAN interfaces
are used since the driver will use the same key slot for the different
GTKs (there's no way for the driver to distinguish the different GTKs
from different AP VLAN interfaces). Thus, only the clients associated
to one AP VLAN interface (the one that was created last) can actually
use broadcast traffic.
Fix this by not programming any GTKs for AP VLAN interfaces into the hw
but fall back to using software crypto. The GTK for the underlying AP
interface is still sent to the driver.
That means, broadcast traffic to stations associated to an AP VLAN
interface is encrypted in software whereas broadcast traffic to
stations associated to the non-VLAN AP interface is encrypted in
hardware.
Cc: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: Fix regulatory bug with multiple cards and delays
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
Reported-by: Mark Mentovai <mark@moxienet.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Mark Mentovai <mark@moxienet.com> Tested-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211: move mutex locking to reg_process_pending_hints()
This will be required in the next patch and it makes the
next patch easier to review.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Mark Mentovai <mark@moxienet.com> Tested-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used earlier in the next few patches.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Mark Mentovai <mark@moxienet.com> Tested-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Tested-by: Mark Mentovai <mark@moxienet.com> Tested-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@kernel.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 20 Nov 2010 02:08:47 +0000 (03:08 +0100)]
ath9k: fix timeout on stopping rx dma
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Cc: stable@kernel.org Signed-off-by: John W. Linville <linville@tuxdriver.com>
macvlan: Introduce 'passthru' mode to takeover the underlying device
With the current default 'vepa' mode, a KVM guest using virtio with
macvtap backend has the following limitations.
- cannot change/add a mac address on the guest virtio-net
- cannot create a vlan device on the guest virtio-net
- cannot enable promiscuous mode on guest virtio-net
To address these limitations, this patch introduces a new mode called
'passthru' when creating a macvlan device which allows takeover of the
underlying device and passing it to a guest using virtio with macvtap
backend.
Only one macvlan device is allowed in passthru mode and it inherits
the mac address from the underlying device and sets it in promiscuous
mode to receive and forward all the packets.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
------------------------------------------------------------------------- Signed-off-by: David S. Miller <davem@davemloft.net>
Juuso Oikarinen [Mon, 22 Nov 2010 10:59:08 +0000 (12:59 +0200)]
wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc
On the disassociation event from the mac80211, the wl12xx driver does not
clear the chipset configuration related to the AP - i.e. it does not perform
a DISCONNECT and then a JOIN with zero SSID and dummy BSSID. Also, it does not
unset the BSSID filter.
Often this is not a problem, as the above is performed upon entering idle
state. But if a scenario arises where a new association is attempted without
cycling through idle state, the new association will fail.
Fix this by resetting the firmware state on disassociation.
Shahar Levi [Mon, 8 Nov 2010 11:20:10 +0000 (11:20 +0000)]
wl1271: Change wl12xx Files Names
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.
Signed-off-by: Shahar Levi <shahar_levi@ti.com> Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Eric Dumazet [Sun, 21 Nov 2010 18:26:44 +0000 (10:26 -0800)]
pktgen: allow faster module unload
Unloading pktgen module needs ~6 seconds on a 64 cpus machine, to stop
64 kthreads.
Add a pktgen_exiting variable to let kernel threads die faster, so that
kthread_stop() doesnt have to wait too long for them. This variable is
not tested in fast path.
Note : Before exiting from pktgen_thread_worker(), we must make sure
kthread_stop() is waiting for this thread to be stopped, like its done
in kernel/softirq.c
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Engelhardt [Sat, 20 Nov 2010 18:07:21 +0000 (18:07 +0000)]
netns: let net_generic take pointer-to-const args
This commit is same in nature as v2.6.37-rc1-755-g3654654; the network
namespace itself is not modified when calling net_generic, so the
parameter can be const.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 20 Nov 2010 07:31:54 +0000 (07:31 +0000)]
packet: use vzalloc()
alloc_one_pg_vec_page() is supposed to return zeroed memory, so use
vzalloc() instead of vmalloc()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Don Skidmore [Sun, 21 Nov 2010 17:55:10 +0000 (09:55 -0800)]
ixgbe: update version number for ixgbe
This will reflect addition of new X540 hardware
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net-next: Add multiqueue support to vmxnet3 driver
Add multiqueue support to vmxnet3 driver
This change adds multiqueue and thus receive side scaling support
to vmxnet3 device driver. Number of rx queues is limited to 1 in cases
where MSI is not configured or one MSIx vector is not available per rx
queue
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com> Reviewed-by: Bhavesh Davda <bhavesh@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net>