gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family
The ACCES PCIe-IDIO-24 device provides 56 lines of digital I/O (24 lines
of optically-isolated non-polarized digital inputs for AC and DC control
signals, 24 lines of isolated solid state FET digital outputs, and 8
non-isolated TTL/CMOS compatible programmable I/O). An interrupt is
generated when any of the inputs change state (low to high or high to
low).
Input filter control is not supported by this driver, and input filters
are deactivated by this driver. These devices are capable of
get_multiple and set_multiple functionality, but these functions have
not yet been implemented for this driver. Change-Of-State (COS)
detection functionality may be configured to fire interrupts on
exclusively rising/falling edges, but this driver currently only
implements COS detection for either both edges or none.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Stephen Boyd [Wed, 10 Jan 2018 01:58:46 +0000 (17:58 -0800)]
gpiolib: Export gpiochip_irqchip_irq_valid() to drivers
Some pinctrl drivers can use the gpiochip irq valid information
to figure out if certain gpios are exposed to the kernel for
usage or not. Expose this API so we can use it in the
pinmux_ops::request ops.
This commit adds GPIO driver for Winbond Super I/Os.
Currently, only W83627UHG model (also known as Nuvoton NCT6627UD)
is supported but in the future a support for other Winbond models,
too, can be added to the driver.
A module parameter "gpios" sets a bitmask of GPIO ports to enable
(bit 0 is GPIO1, bit 1 is GPIO2, etc.).
One should be careful which ports one tinkers with since some
might be managed by the firmware (for functions like powering on and
off, sleeping, BIOS recovery, etc.) and some of GPIO port pins are
physically shared with other devices included in the Super I/O chip.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 27 Dec 2017 15:37:44 +0000 (16:37 +0100)]
gpio: of: Support SPI nonstandard GPIO properties
Before it was clearly established that all GPIO properties in the
device tree shall be named "foo-gpios" (with the deprecated variant
"foo-gpio" for single lines) we unfortunately merged a few bindings
which named the lines "gpio-foo" instead.
This is most prominent in the GPIO SPI driver in Linux which names
the lines "gpio-sck", "gpio-mosi" and "gpio-miso".
As we want to switch the GPIO SPI driver to using descriptors, we
need devm_gpiod_get() to return something reasonable when looking
up these in the device tree.
Put in a special #ifdef:ed kludge to do this special lookup only
for the SPI case and gets compiled out if we're not enabling SPI.
If we have more oddly defined legacy GPIOs like this, they can be
handled in a similar manner.
Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 4 Jan 2018 21:31:11 +0000 (22:31 +0100)]
gpio: label descriptors using the device name
Some GPIO lines appear named "?" in the lsgpio dump due to their
requesting drivers not passing a reasonable label.
Most typically this happens if a device tree node just defines
gpios = <...> and not foo-gpios = <...>, the former gets named
"foo" and the latter gets named "?".
However the struct device passed in is always valid so let's
just label the GPIO with dev_name() on the device if no proper
label was passed.
Cc: Reported-by: Jason Kridner <jkridner@beagleboard.org> Reported-by: Jason Kridner <jkridner@beagleboard.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 29 Dec 2017 12:22:58 +0000 (13:22 +0100)]
gpio: omap: Give unique labels to each GPIO bank/chip
As we need to add GPIO lookup tables to the OMAP platforms, we
need to reference each GPIO chip with a unique label. Use the GPIO
base to name each chip, "gpio-0-31", "gpio-32-63" etc.
gpiolib: don't dereference a desc before validation
The fix restores a proper validation of an input gpio desc, which
might be needed to deal with optional GPIOs correctly.
Fixes: 02e479808b5d ("gpio: Alter semantics of *raw* operations to actually be raw") Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rasmus Villemoes [Thu, 21 Dec 2017 00:27:04 +0000 (01:27 +0100)]
gpio: reduce descriptor validation code size
While we do need macros to be able to return from the "calling"
function, we can still factor the checks done by the VALIDATE_DESC*
macros into a real helper function. This reduces the backslashtitis,
avoids duplicating the logic in the two macros and saves about 1K of
generated code:
Timur Tabi [Wed, 20 Dec 2017 19:10:32 +0000 (13:10 -0600)]
pinctrl: qcom: disable GPIO groups with no pins
pinctrl-msm only accepts an array of GPIOs from 0 to n-1, and it expects
each group to support have only one pin (npins == 1).
We can support "sparse" GPIO maps if we allow for some groups to have zero
pins (npins == 0). These pins are "hidden" from the rest of the driver
and gpiolib.
Access to unavailable GPIOs is blocked via a request callback. If the
requested GPIO is unavailable, -EACCES is returned, which prevents
further access to that GPIO.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We cannot blindly query the direction of all GPIOs when the pins are
first registered. The get_direction callback normally triggers a
read/write to hardware, but we shouldn't be touching the hardware for
an individual GPIO until after it's been properly claimed.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Christophe Leroy [Mon, 18 Dec 2017 10:08:31 +0000 (11:08 +0100)]
gpio: sysfs: correct error handling on 'value' attribute read.
'value' attribute is supposed to only return 0 or 1 according to
the documentation.
With today's implementation, if gpiod_get_value_cansleep() fails
the printed 'value' is a negative value.
This patch ensures that an error is returned on read instead.
Christophe Leroy [Mon, 18 Dec 2017 10:08:29 +0000 (11:08 +0100)]
gpio: sysfs: change 'value' attribute to prealloc
The GPIO 'value' attribute is time critical. A small bench with
'perf record' on the app below shows that 80% of the time spent in
sysfs_kf_seq_show() is spent in memset() for zeroising the buffer.
gpiolib: use kstrdup_const() for gpio_device label
Users often pass a pointer to a static string to gpiochip_add_data()
family of functions. Avoid unnecessary memory allocations with the
provided helper routine.
While at it: use a ternary operator instead of an if else for brevity.
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Quentin Schulz [Tue, 5 Dec 2017 14:46:45 +0000 (15:46 +0100)]
pinctrl: axp209: add programmable ADC muxing value
To prepare for patches that will add support for a new PMIC that has a
different GPIO adc muxing value, add an adc_mux within axp20x_pctl
structure and use it.
To prepare for patches that will add support for a new PMIC that has a
different GPIO input status register, add a gpio_status_offset within
axp20x_pctl structure and use it.
Quentin Schulz [Tue, 5 Dec 2017 14:46:43 +0000 (15:46 +0100)]
pinctrl: axp209: rename everything from gpio to pctl
This driver used to do only GPIO features of the GPIOs in X-Powers
AXP20X. Now that we have migrated everything to the pinctrl subsystem
and added pinctrl features, rename everything related to pinctrl from
gpio to pctl to ease the understanding of differences between GPIO
and pinctrl features.
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Andrew Jeffery [Thu, 30 Nov 2017 03:55:24 +0000 (14:25 +1030)]
gpio: gpiolib: Generalise state persistence beyond sleep
General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.
The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific. I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.
The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Colin Ian King [Tue, 28 Nov 2017 18:23:39 +0000 (18:23 +0000)]
gpio: gpio-stmpe: make various char arrays static const, shrinks object size
Don't populate the read-only arrays edge_det_values, rise_values and
fall_values on the stack but instead make them static and constify them.
Makes the object code smaller by over 240 bytes:
Before:
text data bss dec hex filename
9525 2520 192 12237 2fcd drivers/gpio/gpio-stmpe.o
After:
text data bss dec hex filename
9025 2776 192 11993 2ed9 drivers/gpio/gpio-stmpe.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio: mockup: modify the return value check for devm_irq_sim_init()
As discussed with Marc Zyngier: irq_sim_init() and its devres variant
should return the base of the allocated interrupt range on success
rather than 0. This will be modified later - first, change the way
users handle the return value of these routines.
The debugfs routines returning pointers can return NULL or error codes
embedded with ERR_PTR(). Check the return values with IS_ERR_OR_NULL().
While we're at it: make the error message more specific so it's not
confused with the one emitted when the top-level gpio-mockup debugfs
directory creation fails.
Keep GPIO chip callbacks, event trigger callbacks and mockup chip
setup code visibly separated. We're mostly good - just need to move
the line naming routine below.
Currently each chip has a dedicated directory in debugfs for event
triggers. We use the chip's label for the directory name, but the user
can't really associate these directories with chip names without
parsing the relevant sysfs entries.
Use chip names for directory names. For backward compatibility: create
links pointing to the actual directories named using the chip labels.
gpio: mockup: pass the named_lines parameter over platform_data
Move the last bits of code dealing with module parameters to the init
function. Add a new variable to platform data, which indicates to the
probe function if it should name the GPIO lines. If we ever want to
make the line naming more fine-grained (e.g. per chip switch) it will
be easier this way.
gpio: mockup: merge gpio_mockup_add() into gpio_mockup_probe()
Now that the probe() function only does what is should, there's no
need to split the chip adding logic into a separate routine. Merge
gpio_mockup_add() into gpio_mockup_probe().
We currently create a single platform device in init and then parse
the configuration passed to us via module parameters in probe() before
creating GPIO chips and registering them with the gpiolib framework.
The relation between platform devices and mockup chips should be 1:1.
Create a separate platform device for each mockup chip using convenient
helpers (platform_device_register_resndata()). Pass a platform data
structure to probe() in which the configuration (GPIO base, number of
lines, chip index) extracted from the module params is stored. Make
probe() create a single mockup chip for every platform device.
This approach has several advantages:
- we only parse the module parameters in init() and can bail out before
attaching any device if the input is invalid (currently we would
have to examine kernel logs),
- we'll get notified by the device framework about errors in probe()
for specific chips,
- probe() gets simplified and only does what it's supposed to.
gpio: mockup: parse the module params in init, not probe
If the module parameters are invalid, we should bail out from the init
function instead of detecting it during the device probe. That way we
don't even allow the user to load the module if we don't accept the
arguments.
gpio: omap: initialize gpioirq chip as part of gpiochip_add_data
Hence, series from Thierry Reding [1] merged - the OMAP GPIO driver can be
switched to reuse new feature and just fill new struct gpio_irq_chip before
calling gpiochip_add_data() instead of using few separate gpioirq chip
APIs. gpiochip_add_data() will do the job and create and initialize gpioirq
chip
Do not allow OPEN_SOURCE & OPEN_DRAIN flags in a single request. If
the hardware actually supports enabling both at the same time the
electrical result would be disastrous.
Andy Shevchenko [Fri, 10 Nov 2017 13:40:31 +0000 (15:40 +0200)]
gpiolib: acpi: Consolidate debug output in acpi_gpio_update_gpiod_flags()
We have the duplicated debug strings printed whenever
acpi_gpio_update_gpiod_flags() fails. Instead of doing this by callers,
move the debug output inside function.
In one case convert almost useless pr_debug() to dev_dbg() where
actual consumer of GPIO resource is disclosed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andy Shevchenko [Fri, 10 Nov 2017 13:40:28 +0000 (15:40 +0200)]
gpiolib: acpi: Assign polarity when call acpi_populate_gpio_lookup()
There is no need, since we preserve firmware settings, to override
polarity for GpioInt() resources.
While Documentation/gpio-properties.txt refers to any from GpioIo() /
GpioInt() resources, the active_low flag has been introduced to fill the
gap only for GpioIo() which lacks of that information.
Moreover, in case of GpioInt() existed solution was broken anyway, it
overrides only in one direction, i.e. from 0 to 1, otherwise it would be
still 1 as defined in the resource macro.
So, move the assignment to a right place and forbid to (semi-)override
polarity for GpioInt() type of resources.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 26 Nov 2017 23:03:49 +0000 (15:03 -0800)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Linus Torvalds [Sun, 26 Nov 2017 22:39:20 +0000 (14:39 -0800)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Glexiner:
- unbreak the irq trigger type check for legacy platforms
- a handful fixes for ARM GIC v3/4 interrupt controllers
- a few trivial fixes all over the place
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
irqchip/exiu: Fix return value check in exiu_init()
irqchip/gic-v3-its: Remove artificial dependency on PCI
irqchip/gic-v4: Add forward definition of struct irq_domain_ops
irqchip/gic-v3: pr_err() strings should end with newlines
irqchip/s3c24xx: pr_err() strings should end with newlines
irqchip/gic-v3: Fix ppi-partitions lookup
irqchip/gic-v4: Clear IRQ_DISABLE_UNLAZY again if mapping fails
genirq: Track whether the trigger type has been set
Linus Torvalds [Sun, 26 Nov 2017 22:11:54 +0000 (14:11 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc x86 fixes from Ingo Molnar:
- topology enumeration fixes
- KASAN fix
- two entry fixes (not yet the big series related to KASLR)
- remove obsolete code
- instruction decoder fix
- better /dev/mem sanity checks, hopefully working better this time
- pkeys fixes
- two ACPI fixes
- 5-level paging related fixes
- UMIP fixes that should make application visible faults more debuggable
- boot fix for weird virtualization environment
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
x86/entry/64: Add missing irqflags tracing to native_load_gs_index()
x86/mm/kasan: Don't use vmemmap_populate() to initialize shadow
x86/entry/64: Fix entry_SYSCALL_64_after_hwframe() IRQ tracing
x86/pkeys/selftests: Fix protection keys write() warning
x86/pkeys/selftests: Rename 'si_pkey' to 'siginfo_pkey'
x86/mpx/selftests: Fix up weird arrays
x86/pkeys: Update documentation about availability
x86/umip: Print a warning into the syslog if UMIP-protected instructions are used
x86/smpboot: Fix __max_logical_packages estimate
x86/topology: Avoid wasting 128k for package id array
perf/x86/intel/uncore: Cache logical pkg id in uncore driver
x86/acpi: Reduce code duplication in mp_override_legacy_irq()
x86/acpi: Handle SCI interrupts above legacy space gracefully
x86/boot: Fix boot failure when SMP MP-table is based at 0
x86/mm: Limit mmap() of /dev/mem to valid physical addresses
x86/selftests: Add test for mapping placement for 5-level paging
...
Linus Torvalds [Sun, 26 Nov 2017 21:43:25 +0000 (13:43 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: a documentation fix, a Sparse warning fix and a debugging
fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/debug: Fix task state recording/printout
sched/deadline: Don't use dubious signed bitfields
sched/deadline: Fix the description of runtime accounting in the documentation
Linus Torvalds [Sun, 26 Nov 2017 21:41:48 +0000 (13:41 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc fixes: two PMU driver fixes and a memory leak fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix memory leak triggered by perf --namespace
perf/x86/intel/uncore: Add event constraint for BDX PCU
perf/x86/intel: Hide TSX events when RTM is not supported
Linus Torvalds [Sun, 26 Nov 2017 21:11:18 +0000 (13:11 -0800)]
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Ingo Molnar:
"A handful of objtool fixes, most of them related to making the UAPI
header-syncing warnings easier to read and easier to act upon"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools/headers: Sync objtool UAPI header
objtool: Fix cross-build
objtool: Move kernel headers/code sync check to a script
objtool: Move synced files to their original relative locations
objtool: Make unreachable annotation inline asms explicitly volatile
objtool: Add a comment for the unreachable annotation macros
Russell King [Fri, 24 Nov 2017 23:49:34 +0000 (23:49 +0000)]
ARM: BUG if jumping to usermode address in kernel mode
Detect if we are returning to usermode via the normal kernel exit paths
but the saved PSR value indicates that we are in kernel mode. This
could occur due to corrupted stack state, which has been observed with
"ftracetest".
This ensures that we catch the problem case before we get to user code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Linus Torvalds [Sat, 25 Nov 2017 18:21:54 +0000 (08:21 -1000)]
Merge tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- more changes for HS48 cores: supporting MMUv5, detecting new
micro-arch gizmos
- axs10x platform wiring up reset driver merged in this cycle
- ARC perf driver optimizations
* tag 'arc-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: perf: avoid vmalloc backed mmap
ARCv2: perf: optimize given that num counters <= 32
ARCv2: perf: tweak overflow interrupt
ARC: [plat-axs10x] DTS: Add reset controller node to manage ethernet reset
ARCv2: boot log: updates for HS48: dual-issue, ECC, Loop Buffer
ARCv2: Accomodate HS48 MMUv5 by relaxing MMU ver checking
ARC: [plat-axs10x] auto-select AXS101 or AXS103 given the ISA config
Linus Torvalds [Sat, 25 Nov 2017 18:06:30 +0000 (08:06 -1000)]
Merge tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- use 'pwd' instead of '/bin/pwd' for portability
- clean up Makefiles
- fix ld-option for clang
- fix malloc'ed data size in Kconfig
- fix parallel building along with coccicheck
- fix a minor issue of package building
- prompt to use "rpm-pkg" instead of "rpm"
- clean up *.i and *.lst patterns by "make clean"
* tag 'kbuild-v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: drop $(extra-y) from real-objs-y
kbuild: clean up *.i and *.lst patterns by make clean
kbuild: rpm: prompt to use "rpm-pkg" if "rpm" target is used
kbuild: pkg: use --transform option to prefix paths in tar
coccinelle: fix parallel build with CHECK=scripts/coccicheck
kconfig/symbol.c: use correct pointer type argument for sizeof
kbuild: Set KBUILD_CFLAGS before incl. arch Makefile
kbuild: remove all dummy assignments to obj-
kbuild: create built-in.o automatically if parent directory wants it
kbuild: /bin/pwd -> pwd
Linus Torvalds [Sat, 25 Nov 2017 17:58:25 +0000 (07:58 -1000)]
Merge tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS fixes from David Howells:
- Make AFS file locking work again.
- Don't write to a page that's being written out, but wait for it to
complete.
- Do d_drop() and d_add() in the right places.
- Put keys on error paths.
- Remove some redundant code.
* tag 'afs-fixes-20171124' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: remove redundant assignment of dvnode to itself
afs: cell: Remove unnecessary code in afs_lookup_cell
afs: Fix signal handling in some file ops
afs: Fix some dentry handling in dir ops and missing key_puts
afs: Make afs_write_begin() avoid writing to a page that's being stored
afs: Fix file locking
Linus Torvalds [Sat, 25 Nov 2017 05:44:25 +0000 (19:44 -1000)]
Merge tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"Trimmed second batch of KVM changes for Linux 4.15:
- GICv4 Support for KVM/ARM
- re-introduce support for CPUs without virtual NMI (cc stable) and
allow testing of KVM without virtual NMI on available CPUs
- fix long-standing performance issues with assigned devices on AMD
(cc stable)"
* tag 'kvm-4.15-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
kvm: vmx: Allow disabling virtual NMI support
kvm: vmx: Reinstate support for CPUs without virtual NMI
KVM: SVM: obey guest PAT
KVM: arm/arm64: Don't queue VLPIs on INV/INVALL
KVM: arm/arm64: Fix GICv4 ITS initialization issues
KVM: arm/arm64: GICv4: Theory of operations
KVM: arm/arm64: GICv4: Enable VLPI support
KVM: arm/arm64: GICv4: Prevent userspace from changing doorbell affinity
KVM: arm/arm64: GICv4: Prevent a VM using GICv4 from being saved
KVM: arm/arm64: GICv4: Enable virtual cpuif if VLPIs can be delivered
KVM: arm/arm64: GICv4: Hook vPE scheduling into vgic flush/sync
KVM: arm/arm64: GICv4: Use the doorbell interrupt as an unblocking source
KVM: arm/arm64: GICv4: Add doorbell interrupt handling
KVM: arm/arm64: GICv4: Use pending_last as a scheduling hint
KVM: arm/arm64: GICv4: Handle INVALL applied to a vPE
KVM: arm/arm64: GICv4: Propagate property updates to VLPIs
KVM: arm/arm64: GICv4: Handle MOVALL applied to a vPE
KVM: arm/arm64: GICv4: Handle CLEAR applied to a VLPI
KVM: arm/arm64: GICv4: Propagate affinity changes to the physical ITS
KVM: arm/arm64: GICv4: Unmap VLPI when freeing an LPI
...
Linus Torvalds [Sat, 25 Nov 2017 05:40:12 +0000 (19:40 -1000)]
Merge tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A small batch of fixes, about 50% tagged for stable and the rest for
recently merged code.
There's one more fix for the >128T handling on hash. Once a process
had requested a single mmap above 128T we would then always search
above 128T. The correct behaviour is to consider the hint address in
isolation for each mmap request.
Then a couple of fixes for the IMC PMU, a missing EXPORT_SYMBOL in
VAS, a fix for STRICT_KERNEL_RWX on 32-bit, and a fix to correctly
identify P9 DD2.1 but in code that is currently not used by default.
* tag 'powerpc-4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Fix Power9 DD2.1 logic in DT CPU features
powerpc/perf: Fix IMC_MAX_PMU macro
powerpc/perf: Fix pmu_count to count only nest imc pmus
powerpc: Fix boot on BOOK3S_32 with CONFIG_STRICT_KERNEL_RWX
powerpc/perf/imc: Use cpu_to_node() not topology_physical_package_id()
powerpc/vas: Export chip_to_vas_id()
powerpc/64s/slice: Use addr limit when computing slice mask
Linus Torvalds [Sat, 25 Nov 2017 05:19:20 +0000 (19:19 -1000)]
Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This series is predominantly bug-fixes, with a few small improvements
that have been outstanding over the last release cycle.
As usual, the associated bug-fixes have CC' tags for stable.
Also, things have been particularly quiet wrt new developments the
last months, with most folks continuing to focus on stability atop 4.x
stable kernels for their respective production configurations.
Also at this point, the stable trees have been synced up with
mainline. This will continue to be a priority, as production users
tend to run exclusively atop stable kernels, a few releases behind
mainline.
- Fix quiese during transport_write_pending_qf endless loop (nab)
- Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK in 3.14+
(Don White + nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (35 commits)
tcmu: Add a missing unlock on an error path
tcmu: Fix some memory corruption
iscsi-target: Fix non-immediate TMR reference leak
iscsi-target: Make TASK_REASSIGN use proper se_cmd->cmd_kref
target: Avoid early CMD_T_PRE_EXECUTE failures during ABORT_TASK
target: Fix quiese during transport_write_pending_qf endless loop
target: Fix caw_sem leak in transport_generic_request_failure
target: Fix QUEUE_FULL + SCSI task attribute handling
iSCSI-target: Use common error handling code in iscsi_decode_text_input()
target/iscsi: Detect conn_cmd_list corruption early
target/iscsi: Fix a race condition in iscsit_add_reject_from_cmd()
target/iscsi: Modify iscsit_do_crypto_hash_buf() prototype
target/iscsi: Fix endianness in an error message
target/iscsi: Use min() in iscsit_dump_data_payload() instead of open-coding it
target/iscsi: Define OFFLOAD_BUF_SIZE once
target: Inline transport_put_cmd()
target: Suppress gcc 7 fallthrough warnings
target: Move a declaration of a global variable into a header file
tcmu: fix double se_cmd completion
target: return SAM_STAT_TASK_SET_FULL for TCM_OUT_OF_RESOURCES
...
Colin Ian King [Mon, 20 Nov 2017 13:58:20 +0000 (13:58 +0000)]
afs: remove redundant assignment of dvnode to itself
The assignment of dvnode to itself is redundant and can be removed.
Cleans up warning detected by cppcheck:
fs/afs/dir.c:975: (warning) Redundant assignment of 'dvnode' to itself.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 20 Nov 2017 22:41:00 +0000 (22:41 +0000)]
afs: Fix signal handling in some file ops
afs_mkdir(), afs_create(), afs_link() and afs_symlink() all need to drop
the target dentry if a signal causes the operation to be killed immediately
before we try to contact the server.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 20 Nov 2017 23:04:08 +0000 (23:04 +0000)]
afs: Fix some dentry handling in dir ops and missing key_puts
Fix some of dentry handling in AFS directory ops:
(1) Do d_drop() on the new_dentry before assigning a new inode to it in
afs_vnode_new_inode(). It's fine to do this before calling afs_iget()
because the operation has taken place on the server.
(2) Replace d_instantiate()/d_rehash() with d_add().
(3) Don't d_drop() the new_dentry in afs_rename() on error.
Also fix afs_link() and afs_rename() to call key_put() on all error paths
where the key is taken.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Sat, 18 Nov 2017 00:13:30 +0000 (00:13 +0000)]
afs: Make afs_write_begin() avoid writing to a page that's being stored
Make afs_write_begin() wait for a page that's marked PG_writeback because:
(1) We need to avoid interference with the data being stored so that the
data on the server ends up in a defined state.
(2) page->private is used to track the window of dirty data within a page,
but it's also used by the storage code to track what's being written,
being cleared by the completion notification. Ownership can't be
relinquished by the storage code until completion because it a store
fails, the data must be remarked dirty.
Tracing shows something like the following (edited):
The clear (completion) corresponding to the store+ (store continuation from
a previous page) happens between the second begin (afs_write_begin) and the
store corresponding to that. This results in the second store not seeing
any data to write back, leading to the following warning:
Thomas Gleixner [Wed, 22 Nov 2017 12:05:48 +0000 (13:05 +0100)]
sched/debug: Fix task state recording/printout
The recent conversion of the task state recording to use task_state_index()
broke the sched_switch tracepoint task state output.
task_state_index() returns surprisingly an index (0-7) which is then
printed with __print_flags() applying bitmasks. Not really working and
resulting in weird states like 'prev_state=t' instead of 'prev_state=I'.
Use TASK_REPORT_MAX instead of TASK_STATE_MAX to report preemption. Build a
bitmask from the return value of task_state_index() and store it in
entry->prev_state, which makes __print_flags() work as expected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: stable@vger.kernel.org Fixes: efb40f588b43 ("sched/tracing: Fix trace_sched_switch task-state printing") Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1711221304180.1751@nanos Signed-off-by: Ingo Molnar <mingo@kernel.org>
Masami Hiramatsu [Fri, 24 Nov 2017 04:56:30 +0000 (13:56 +0900)]
x86/decoder: Add new TEST instruction pattern
The kbuild test robot reported this build warning:
Warning: arch/x86/tools/test_get_len found difference at <jump_table>:ffffffff8103dd2c
Warning: ffffffff8103dd82: f6 09 d8 testb $0xd8,(%rcx)
Warning: objdump says 3 bytes, but insn_get_length() says 2
Warning: decoded and checked 1569014 instructions with 1 warnings
This sequence seems to be a new instruction not in the opcode map in the Intel SDM.
The instruction sequence is "F6 09 d8", means Group3(F6), MOD(00)REG(001)RM(001), and 0xd8.
Intel SDM vol2 A.4 Table A-6 said the table index in the group is "Encoding of Bits 5,4,3 of
the ModR/M Byte (bits 2,1,0 in parenthesis)"
In that table, opcodes listed by the index REG bits as:
1) Fix PCI IDs of 9000 series iwlwifi devices, from Luca Coelho.
2) bpf offload bug fixes from Jakub Kicinski.
3) Fix bpf verifier to NOP out code which is dead at run time because
due to branch pruning the verifier will not explore such
instructions. From Alexei Starovoitov.
4) Fix crash when deleting secondary chains in packet scheduler
classifier. From Roman Kapl.
5) Fix buffer management bugs in smc, from Ursula Braun.
6) Fix regression in anycast route handling, from David Ahern.
7) Fix link settings regression in r8169, from Tobias Jakobi.
8) Add back enough UFO support so that live migration still works, from
Willem de Bruijn.
9) Linearize enough packet data for the full extent to which the ipvlan
code will inspect the packet headers, from Gao Feng.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
ipvlan: Fix insufficient skb linear check for ipv6 icmp
ipvlan: Fix insufficient skb linear check for arp
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
net: accept UFO datagrams from tuntap and packet
net: realtek: r8169: implement set_link_ksettings()
net: ipv6: Fixup device for anycast routes during copy
net/smc: Fix preinitialization of buf_desc in __smc_buf_create()
net/smc: use sk_rcvbuf as start for rmb creation
ipv6: Do not consider linkdown nexthops during multipath
net: sched: fix crash when deleting secondary chains
net: phy: cortina: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
bpf: fix branch pruning logic
bpf: change bpf_perf_event_output arg5 type to ARG_CONST_SIZE_OR_ZERO
bpf: change bpf_probe_read_str arg2 type to ARG_CONST_SIZE_OR_ZERO
bpf: remove explicit handling of 0 for arg2 in bpf_probe_read
bpf: introduce ARG_PTR_TO_MEM_OR_NULL
i40evf: Use smp_rmb rather than read_barrier_depends
fm10k: Use smp_rmb rather than read_barrier_depends
igb: Use smp_rmb rather than read_barrier_depends
...