Add mt7615_mcu_send_ram_firmware routine since mt7615_load_ram runs the
same code to send ram firmware to cr4 and n9 mcus. Moreover rename
gen_dl_mode in mt7615_mcu_gen_dl_mode.
This patch does not introduce any behaviour change, it is just code
refactor.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Suggested-by: Sebastian Gottschall <s.gottschall@newmedia-net.de> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 1 Jul 2019 18:17:40 +0000 (20:17 +0200)]
mt76: mt7615: clean up FWDL TXQ during/after firmware upload
Since we don't clean that tx queue from the tx tasklet, we need to do it
after the firmware upload is done. This patch also adds a cleanup step during
the upload, to help reclaim memory faster.
Fixes unprocessed queued frames eating up memory long after the firmware
upload has already completed
Fix the following sparse warning in __mt7615_mcu_msg_send:
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
restricted __le16 degrades to integer
drivers/net/wireless/mediatek/mt76/mt7615/mcu.c:78:15: sparse: warning:
cast from restricted __le16
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Mon, 1 Jul 2019 11:15:07 +0000 (13:15 +0200)]
mt76: round up length on mt76_wr_copy
When beacon length is not a multiple of 4, the beacon could be sent with
the last 1-3 bytes corrupted. The skb data is guaranteed to have enough
room for reading beyond the end, because it is always followed by
skb_shared_info, so rounding up is safe.
All other callers of mt76_wr_copy have multiple-of-4 length already.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
Rafał Miłecki [Thu, 29 Aug 2019 08:27:01 +0000 (10:27 +0200)]
brcmfmac: get chip's default RAM info during PCIe setup
Getting RAM info just once per driver's lifetime (during chip
recognition) is not enough as it may get adjusted later (depending on
the used firmware). Subsequent inits may load different firmwares so a
full RAM recognition is required on every PCIe setup. This is especially
important since implementing hardware reset on a firmware crash.
Moreover calling brcmf_chip_get_raminfo() makes sure that RAM core is
up. It's important as having BCMA_CORE_SYS_MEM down on BCM4366 was
resulting in firmware failing to initialize and following error:
[ 65.657546] brcmfmac 0000:01:00.0: brcmf_pcie_download_fw_nvram: Invalid shared RAM address 0x04000001
This change makes brcmf_chip_get_raminfo() call during chip recognition
redundant for PCIe devices but SDIO and USB still need it and it's a
very small overhead anyway.
Fixes: 4684997d9eea ("brcmfmac: reset PCIe bus on a firmware crash") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Tue, 27 Aug 2019 08:16:20 +0000 (09:16 +0100)]
bcma: fix incorrect update of BCMA_CORE_PCI_MDIO_DATA
An earlier commit re-worked the setting of the bitmask and is now
assigning v with some bit flags rather than bitwise or-ing them
into v, consequently the earlier bit-settings of v are being lost.
Fix this by replacing an assignment with the bitwise or instead.
Addresses-Coverity: ("Unused value") Fixes: 2be25cac8402 ("bcma: add constants for PCI and use them") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Xulin Sun [Fri, 23 Aug 2019 07:47:08 +0000 (15:47 +0800)]
brcmfmac: replace strncpy() by strscpy()
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2x00: do not set IEEE80211_TX_STAT_AMPDU_NO_BACK on tx status
According to documentation IEEE80211_TX_STAT_AMPDU_NO_BACK is suppose
to be used when we do not recive BA (BlockAck). However on rt2x00 we
use it when remote station fail to decode one or more subframes within
AMPDU (some bits are not set in BlockAck bitmap). Setting the flag result
in sent of BAR (BlockAck Request) frame and this might result of abuse
of BA session, since remote station can sent BA with incorrect
sequence numbers after receiving BAR. This problem is visible especially
when connecting two rt2800 devices.
Previously I observed some performance benefits when using the flag
when connecting with iwlwifi devices. But currently possibly due
to reacent changes in rt2x00 removing the flag has no effect on
those test cases.
So remove the IEEE80211_TX_STAT_AMPDU_NO_BACK.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wenwen Wang [Fri, 16 Aug 2019 03:50:02 +0000 (22:50 -0500)]
airo: fix memory leaks
In proc_BSSList_open(), 'file->private_data' is allocated through kzalloc()
and 'data->rbuffer' is allocated through kmalloc(). In the following
execution, if an error occurs, they are not deallocated, leading to memory
leaks. To fix this issue, free the allocated memory regions before
returning the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Oliver Neukum [Tue, 13 Aug 2019 12:04:11 +0000 (14:04 +0200)]
zd1211rw: remove false assertion from zd_mac_clear()
The function is called before the lock which is asserted was ever used.
Just remove it.
Reported-by: syzbot+74c65761783d66a9c97c@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Colin Ian King [Fri, 9 Aug 2019 17:22:17 +0000 (18:22 +0100)]
brcmfmac: remove redundant assignment to pointer hash
The pointer hash is being initialized with a value that is never read
and is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Fri, 9 Aug 2019 08:53:08 +0000 (16:53 +0800)]
bcma: remove two unused variables
drivers/bcma/driver_mips.c:70:18: warning:
ipsflag_irq_shift defined but not used [-Wunused-const-variable=]
drivers/bcma/driver_mips.c:62:18: warning:
ipsflag_irq_mask defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jia-Ju Bai [Mon, 29 Jul 2019 09:56:52 +0000 (17:56 +0800)]
brcm80211: Avoid possible null-pointer dereferences in wlc_phy_radio_init_2056()
In wlc_phy_radio_init_2056(), regs_SYN_2056_ptr, regs_TX_2056_ptr and
regs_RX_2056_ptr may be not assigned, and thus they are still NULL.
Then, they are used on lines 20042-20050:
wlc_phy_init_radio_regs(pi, regs_SYN_2056_ptr, (u16) RADIO_2056_SYN);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX0);
wlc_phy_init_radio_regs(pi, regs_TX_2056_ptr, (u16) RADIO_2056_TX1);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX0);
wlc_phy_init_radio_regs(pi, regs_RX_2056_ptr, (u16) RADIO_2056_RX1);
Thus, possible null-pointer dereferences may occur.
To avoid these bugs, when these variables are not assigned,
wlc_phy_radio_init_2056() directly returns.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tested-by: Ján Veselý <jano.vesely@gmail.com> Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Yu-Yen Ting <steventing@realtek.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Jian-Hong Pan [Tue, 3 Sep 2019 09:14:06 +0000 (17:14 +0800)]
rtw88: pci: Move a mass of jobs in hw IRQ to soft IRQ
There is a mass of jobs between spin lock and unlock in the hardware
IRQ which will occupy much time originally. To make system work more
efficiently, this patch moves the jobs to the soft IRQ (bottom half) to
reduce the time in hardware IRQ.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Wed, 14 Aug 2019 10:46:42 +0000 (13:46 +0300)]
rtw88: Fix an error message
The WARN_ON() macro takes a condition, not a warning message. I've
changed this to use WARN() instead.
Fixes: 4136214f7c46 ("rtw88: add BT co-existence support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 3 Sep 2019 01:18:13 +0000 (20:18 -0500)]
rtlwifi: rtl8192ce: Fix incorrect returned values
In commit 98fd8db59a00 ("rtlwifi: rtl8192ce: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 98fd8db59a00 ("rtlwifi: rtl8192ce: Convert macros that set descriptor") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 3 Sep 2019 01:18:12 +0000 (20:18 -0500)]
rtlwifi: rtl8188ee: Fix incorrect returned values
In commit 36eda7568f2e ("rtlwifi: rtl8188ee: Convert macros that set
descriptor"), all the routines that get fields from a descriptor were
changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 36eda7568f2e ("rtlwifi: rtl8188ee: Convert macros that set descriptor") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Tue, 3 Sep 2019 01:18:11 +0000 (20:18 -0500)]
rtlwifi: rtl8821ae: Fix incorrect returned values
In commit bd421dab7515 ("rtlwifi: rtl8821ae: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: bd421dab7515 ("rtlwifi: rtl8821ae: Convert macros that set descriptor") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sun, 1 Sep 2019 15:47:06 +0000 (10:47 -0500)]
rtlwifi: rtl8192cu: Convert inline routines to little-endian words
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sun, 1 Sep 2019 15:47:05 +0000 (10:47 -0500)]
rtlwifi: rtl8192cu: Convert macros that set descriptor
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sun, 1 Sep 2019 15:47:04 +0000 (10:47 -0500)]
rtlwifi: rtl8192cu: Replace local bit manipulation macros
This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sat, 31 Aug 2019 18:06:43 +0000 (13:06 -0500)]
rtlwifi: rtl8192ee: Convert inline routines to little-endian words
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sat, 31 Aug 2019 18:06:42 +0000 (13:06 -0500)]
rtlwifi: rtl8192ee: Convert macros that set descriptor
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Sat, 31 Aug 2019 18:06:41 +0000 (13:06 -0500)]
rtlwifi: rtl8192ee: Replace local bit manipulation macros
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Mon, 26 Aug 2019 22:03:44 +0000 (17:03 -0500)]
rtlwifi: rtl_pci: Fix memory leak when hardware init fails
If the call to hw_init() fails for any of the drivers, the driver will
leak memory that was allocated in BT coexistence setup. Technically, each
of the drivers should have done this free; however placing it in rtl_pci
fixes all the drivers with only a single patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Fri, 16 Aug 2019 14:05:13 +0000 (22:05 +0800)]
rtlwifi: remove unused variables 'RTL8712_SDIO_EFUSE_TABLE' and 'MAX_PGPKT_SIZE'
drivers/net/wireless/realtek/rtlwifi/efuse.c:16:31:
warning: RTL8712_SDIO_EFUSE_TABLE defined but not used [-Wunused-const-variable=]
drivers/net/wireless/realtek/rtlwifi/efuse.c:9:17:
warning: MAX_PGPKT_SIZE defined but not used [-Wunused-const-variable=]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Larry Finger [Mon, 12 Aug 2019 19:27:41 +0000 (14:27 -0500)]
rtlwifi: rtl8192cu: Fix value set in descriptor
In the process of converting the bit manipulation macros were converted
to use GENMASK(), the compiler reported a value too big for the field.
The offending statement was trying to write 0x100 into a 5-bit field.
An accompaning comment says to set bit 3, thus the code is changed
appropriately.
This error has been in the driver since its initial submission.
Fixes: 29d00a3e46bb ("rtlwifi: rtl8192cu: Add routine trx") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix spurious warning message when building with W=1:
CC [M] drivers/net/wireless/realtek/rtlwifi/usb.o
drivers/net/wireless/realtek/rtlwifi/usb.c:243: warning: Cannot understand * on line 243 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:760: warning: Cannot understand * on line 760 - I thought it was a doc line
drivers/net/wireless/realtek/rtlwifi/usb.c:790: warning: Cannot understand * on line 790 - I thought it was a doc line
Clean up the comment format.
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David S. Miller [Mon, 2 Sep 2019 19:07:46 +0000 (12:07 -0700)]
Merge branch 'mvpp2-per-cpu-buffers'
Matteo Croce says:
====================
mvpp2: per-cpu buffers
This patchset workarounds an PP2 HW limitation which prevents to use
per-cpu rx buffers.
The first patch is just a refactor to prepare for the second one.
The second one allocates percpu buffers if the following conditions are met:
- CPU number is less or equal 4
- no port is using jumbo frames
If the following conditions are not met at load time, of jumbo frame is enabled
later on, the shared allocation is reverted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Sat, 31 Aug 2019 12:46:19 +0000 (15:46 +0300)]
net: dsa: Fix off-by-one number of calls to devlink_port_unregister
When a function such as dsa_slave_create fails, currently the following
stack trace can be seen:
[ 2.038342] sja1105 spi0.1: Probed switch chip: SJA1105T
[ 2.054556] sja1105 spi0.1: Reset switch and programmed static config
[ 2.063837] sja1105 spi0.1: Enabled switch tagging
[ 2.068706] fsl-gianfar soc:ethernet@2d90000 eth2: error -19 setting up slave phy
[ 2.076371] ------------[ cut here ]------------
[ 2.080973] WARNING: CPU: 1 PID: 21 at net/core/devlink.c:6184 devlink_free+0x1b4/0x1c0
[ 2.088954] Modules linked in:
[ 2.092005] CPU: 1 PID: 21 Comm: kworker/1:1 Not tainted 5.3.0-rc6-01360-g41b52e38d2b6-dirty #1746
[ 2.100912] Hardware name: Freescale LS1021A
[ 2.105162] Workqueue: events deferred_probe_work_func
[ 2.110287] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 2.117992] [<c030d8cc>] (show_stack) from [<c10b08d8>] (dump_stack+0xb4/0xc8)
[ 2.125180] [<c10b08d8>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 2.132018] [<c0349d04>] (__warn) from [<c0349e34>] (warn_slowpath_null+0x40/0x48)
[ 2.139549] [<c0349e34>] (warn_slowpath_null) from [<c0f19d74>] (devlink_free+0x1b4/0x1c0)
[ 2.147772] [<c0f19d74>] (devlink_free) from [<c1064fc0>] (dsa_switch_teardown+0x60/0x6c)
[ 2.155907] [<c1064fc0>] (dsa_switch_teardown) from [<c1065950>] (dsa_register_switch+0x8e4/0xaa8)
[ 2.164821] [<c1065950>] (dsa_register_switch) from [<c0ba7fe4>] (sja1105_probe+0x21c/0x2ec)
[ 2.173216] [<c0ba7fe4>] (sja1105_probe) from [<c0b35948>] (spi_drv_probe+0x80/0xa4)
[ 2.180920] [<c0b35948>] (spi_drv_probe) from [<c0a4c1cc>] (really_probe+0x108/0x400)
[ 2.188711] [<c0a4c1cc>] (really_probe) from [<c0a4c694>] (driver_probe_device+0x78/0x1bc)
[ 2.196933] [<c0a4c694>] (driver_probe_device) from [<c0a4a3dc>] (bus_for_each_drv+0x58/0xb8)
[ 2.205414] [<c0a4a3dc>] (bus_for_each_drv) from [<c0a4c024>] (__device_attach+0xd0/0x168)
[ 2.213637] [<c0a4c024>] (__device_attach) from [<c0a4b1d0>] (bus_probe_device+0x84/0x8c)
[ 2.221772] [<c0a4b1d0>] (bus_probe_device) from [<c0a4b72c>] (deferred_probe_work_func+0x84/0xc4)
[ 2.230686] [<c0a4b72c>] (deferred_probe_work_func) from [<c03650a4>] (process_one_work+0x218/0x510)
[ 2.239772] [<c03650a4>] (process_one_work) from [<c03660d8>] (worker_thread+0x2a8/0x5c0)
[ 2.247908] [<c03660d8>] (worker_thread) from [<c036b348>] (kthread+0x148/0x150)
[ 2.255265] [<c036b348>] (kthread) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
[ 2.262444] Exception stack(0xea965fb0 to 0xea965ff8)
[ 2.267466] 5fa0: 00000000000000000000000000000000
[ 2.275598] 5fc0: 0000000000000000000000000000000000000000000000000000000000000000
[ 2.283729] 5fe0: 000000000000000000000000000000000000001300000000
[ 2.290333] ---[ end trace ca5d506728a0581a ]---
devlink_free is complaining right here:
WARN_ON(!list_empty(&devlink->port_list));
This happens because devlink_port_unregister is no longer done right
away in dsa_port_setup when a DSA_PORT_TYPE_USER has failed.
Vivien said about this change that:
Also no need to call devlink_port_unregister from within dsa_port_setup
as this step is inconditionally handled by dsa_port_teardown on error.
which is not really true. The devlink_port_unregister function _is_
being called unconditionally from within dsa_port_setup, but not for
this port that just failed, just for the previous ones which were set
up.
ports_teardown:
for (i = 0; i < port; i++)
dsa_port_teardown(&ds->ports[i]);
Initially I was tempted to fix this by extending the "for" loop to also
cover the port that failed during setup. But this could have potentially
unforeseen consequences unrelated to devlink_port or even other types of
ports than user ports, which I can't really test for. For example, if
for some reason devlink_port_register itself would fail, then
unconditionally unregistering it in dsa_port_teardown would not be a
smart idea. The list might go on.
So just make dsa_port_setup undo the setup it had done upon failure, and
let the for loop undo the work of setting up the previous ports, which
are guaranteed to be brought up to a consistent state.
Fixes: 955222ca5281 ("net: dsa: use a single switch statement for port setup") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
Merge tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
Following Marek's work on the abstraction of the SERDES lanes mapping, this
series trades the .serdes_irq_setup and .serdes_irq_free callbacks for new
.serdes_irq_mapping, .serdes_irq_enable and .serdes_irq_status operations.
This has the benefit to limit the various SERDES implementations to simple
register accesses only; centralize the IRQ handling and mutex locking logic;
as well as reducing boilerplate in the driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:33 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: pass lane to .serdes_power
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:30 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: simplify .serdes_get_lane
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:28 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: fix SERDES IRQ mapping
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Sat, 31 Aug 2019 20:18:27 +0000 (16:18 -0400)]
net: dsa: mv88e6xxx: check errors in mv88e6352_serdes_irq_link
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Sat, 31 Aug 2019 12:29:11 +0000 (12:29 +0000)]
net: hns3: remove set but not used variable 'qos'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 70a214903da9 ("net: hns3: reduce the parameters of some functions") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sat, 31 Aug 2019 07:29:49 +0000 (08:29 +0100)]
net: hns3: remove redundant assignment to pointer reg_info
Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: seeq: Fix the function used to release some memory in an error handling path
In commit 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe82 ("sgiseeq: replace use of dma_cache_wback_inv") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Sun, 1 Sep 2019 15:52:05 +0000 (16:52 +0100)]
netlabel: remove redundant assignment to pointer iter
Pointer iter is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Paul Moore <paul@paul-moore.com> Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 uses a different register for VLAN offloading config,
therefore don't set bit RxVlan.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Fix the bogus detection of 32bit user mode for uretprobes which
caused corruption of the user return address resulting in
application crashes. In the uprobes handler in_ia32_syscall() is
obviously always returning false on a 64bit kernel. Use
user_64bit_mode() instead which works correctly.
- Prevent large page splitting when ftrace flips RW/RO on the kernel
text which caused iTLB performance issues. Ftrace wants to be
converted to text_poke() which avoids the problem, but for now
allow large page preservation in the static protections check when
the change request spawns a full large page.
- Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
is configured via device tree. In the device tree case the GSI 1:1
mapping is meaningless therefore the lower bound which protects the
GSI range on ACPI machines is irrelevant. Return the lower bound
which the core hands to the function instead of blindly returning 0
which causes the core to allocate the invalid virtual interupt
number 0 which in turn prevents all drivers from allocating and
requesting an interrupt.
- Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
APIC driver. That uses physical destination mode where LDR/DFR are
ignored, but the initialization and the missing clear of LDR caused
the APIC to be left in a inconsistent state on kexec/reboot.
- Clear LDR when clearing the APIC registers so the APIC is in a well
defined state.
- Initialize variables proper in the find_trampoline_placement()
code.
- Silence GCC( build warning for the real mode part of the build"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
x86/apic: Include the LDR when clearing out APIC registers
x86/apic: Do not initialize LDR and DFR for bigsmp
uprobes/x86: Fix detection of 32-bit user mode
x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"Two fixes for perf x86 hardware implementations:
- Restrict the period on Nehalem machines to prevent perf from
hogging the CPU
- Prevent the AMD IBS driver from overwriting the hardwre controlled
and pre-seeded reserved bits (0-6) in the count register which
caused a sample bias for dispatched micro-ops"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
perf/x86/intel: Restrict period on Nehalem
Ryan M. Collins [Fri, 30 Aug 2019 18:49:55 +0000 (14:49 -0400)]
net: bcmgenet: use ethtool_op_get_ts_info()
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e7991 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Doug Berger <opendmb@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 16:51:47 +0000 (18:51 +0200)]
tc-testing: don't hardcode 'ip' in nsPlugin.py
the following tdc test fails on Fedora:
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
-----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 clsact"
-----> prepare stage *** Error message: "/bin/sh: ip: command not found"
returncode 127; expected [0]
-----> prepare stage *** Aborting test run.
Let nsPlugin.py use the 'IP' variable introduced with commit 92c1a19e2fb9
("tc-tests: added path to ip command in tdc"), so that the path to 'ip' is
correctly resolved to the value we have in tdc_config.py.
# ./tdc.py -e 2638
-- ns/SubPlugin.__init__
Test 2638: Add matchall and try to get it
All test results:
1..1
ok 1 2638 - Add matchall and try to get it
Fixes: 489ce2f42514 ("tc-testing: Restore original behaviour for namespaces in tdc") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 06:46:13 +0000 (23:46 -0700)]
Merge branch 'Minor-cleanup-in-devlink'
Parav Pandit says:
====================
Minor cleanup in devlink
Two minor cleanup in devlink.
Patch-1 Explicitly defines devlink port index as unsigned int
Patch-2 Uses switch-case to handle different port flavours attributes
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Fri, 30 Aug 2019 10:39:44 +0000 (05:39 -0500)]
devlink: Make port index data type as unsigned int
Devlink port index attribute is returned to users as u32 through
netlink response.
Change index data type from 'unsigned' to 'unsigned int' to avoid
below checkpatch.pl warning.
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
81: FILE: include/net/devlink.h:81:
+ unsigned index;
Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 1 Sep 2019 06:44:28 +0000 (23:44 -0700)]
Merge branch 'net-tls-add-socket-diag'
Davide Caratti says:
====================
net: tls: add socket diag
The current kernel does not provide any diagnostic tool, except
getsockopt(TCP_ULP), to know more about TCP sockets that have an upper
layer protocol (ULP) on top of them. This series extends the set of
information exported by INET_DIAG_INFO, to include data that are
specific to the ULP (and that might be meaningful for debug/testing
purposes).
patch 1/3 ensures that the control plane reads/updates ULP specific data
using RCU.
patch 2/3 extends INET_DIAG_INFO and allows knowing the ULP name for
each TCP socket that has done setsockopt(TCP_ULP) successfully.
patch 3/3 extends kTLS to let programs like 'ss' know the protocol
version and the cipher in use.
Changes since v2:
- remove unneeded #ifdef and fix reverse christmas tree in
tls_get_info(), thanks to Jakub Kicinski
Changes since v1:
- don't worry about grace period when accessing ulp_ops, thanks to
Jakub Kicinski and Eric Dumazet
- use rcu_dereference() to access ULP data in tls get_info(), and
test against NULL value, thanks to Jakub Kicinski
- move RCU protected section inside tls get_info(), thanks to Jakub
Kicinski
Changes since RFC:
- some coding style fixes, thanks to Jakub Kicinski
- add X_UNSPEC as lowest value of uAPI enums, thanks to Jakub Kicinski
- fix assignment of struct nlattr *start, thanks to Jakub Kicinski
- let tls dump RXCONF and TXCONF, suggested by Jakub Kicinski
- don't dump anything if TLS version or cipher are 0 (but still return a
constant size in get_aux_size()), thanks to Boris Pismenny
- constify first argument of get_info() and get_size()
- use RCU to access access ulp_ops, like it's done for ca_ops
- add patch 1/3, from Jakub Kicinski
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 10:25:49 +0000 (12:25 +0200)]
net: tls: export protocol version, cipher, tx_conf/rx_conf to socket diag
When an application configures kernel TLS on top of a TCP socket, it's
now possible for inet_diag_handler() to collect information regarding the
protocol version, the cipher type and TX / RX configuration, in case
INET_DIAG_INFO is requested.
Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 30 Aug 2019 10:25:48 +0000 (12:25 +0200)]
tcp: ulp: add functions to dump ulp-specific information
currently, only getsockopt(TCP_ULP) can be invoked to know if a ULP is on
top of a TCP socket. Extend idiag_get_aux() and idiag_get_aux_size(),
introduced by commit b37e88407c1d ("inet_diag: allow protocols to provide
additional data"), to report the ULP name and other information that can
be made available by the ULP through optional functions.
Users having CAP_NET_ADMIN privileges will then be able to retrieve this
information through inet_diag_handler, if they specify INET_DIAG_INFO in
the request.
Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:38 +0000 (12:08 +0000)]
net: aquantia: fix out of memory condition on rx side
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864b0 ("net: ethernet: aquantia: Vector operations") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Igor Russkikh [Fri, 30 Aug 2019 12:08:36 +0000 (12:08 +0000)]
net: aquantia: linkstate irq should be oneshot
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes: 4c83f170b3ac ("net: aquantia: link status irq handling") Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Reported-by: Michael Symolkin <Michael.Symolkin@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:35 +0000 (12:08 +0000)]
net: aquantia: reapply vlan filters on up
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:33 +0000 (12:08 +0000)]
net: aquantia: fix limit of vlan filters
Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode
Fixes: 48dd73d08d4dd ("net: aquantia: fix vlans not working over bridged network") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Fri, 30 Aug 2019 12:08:30 +0000 (12:08 +0000)]
net: aquantia: fix removal of vlan 0
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes: 7975d2aff5afb ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:23 +0000 (04:07 +0300)]
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
The discussion to be made is absolutely the same as in the case of
previous patch ("taprio: Set default link speed to 10 Mbps in
taprio_set_picos_per_byte"). Nothing is lost when setting a default.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com> Fixes: e0a7683d30e9 ("net/sched: cbs: fix port_rate miscalculation") Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:22 +0000 (04:07 +0300)]
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
The taprio budget needs to be adapted at runtime according to interface
link speed. But that handling is problematic.
For one thing, installing a qdisc on an interface that doesn't have
carrier is not illegal. But taprio prints the following stack trace:
[ 31.851373] ------------[ cut here ]------------
[ 31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4
[ 31.864566] taprio: dequeue() called with unknown picos per byte.
[ 31.864570] Modules linked in:
[ 31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689
[ 31.881398] Hardware name: Freescale LS1021A
[ 31.885661] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[ 31.893368] [<c030d8cc>] (show_stack) from [<c10ac958>] (dump_stack+0xb4/0xc8)
[ 31.900555] [<c10ac958>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[ 31.907395] [<c0349d04>] (__warn) from [<c0349d64>] (warn_slowpath_fmt+0x48/0x6c)
[ 31.914841] [<c0349d64>] (warn_slowpath_fmt) from [<c0f38db4>] (taprio_dequeue+0x1a8/0x2d4)
[ 31.923150] [<c0f38db4>] (taprio_dequeue) from [<c0f227b0>] (__qdisc_run+0x90/0x61c)
[ 31.930856] [<c0f227b0>] (__qdisc_run) from [<c0ec82ac>] (net_tx_action+0x12c/0x2bc)
[ 31.938560] [<c0ec82ac>] (net_tx_action) from [<c0302298>] (__do_softirq+0x130/0x3c8)
[ 31.946350] [<c0302298>] (__do_softirq) from [<c03502a0>] (irq_exit+0xbc/0xd8)
[ 31.953536] [<c03502a0>] (irq_exit) from [<c03a4808>] (__handle_domain_irq+0x60/0xb4)
[ 31.961328] [<c03a4808>] (__handle_domain_irq) from [<c0754478>] (gic_handle_irq+0x58/0x9c)
[ 31.969638] [<c0754478>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[ 31.977076] Exception stack(0xe8167b20 to 0xe8167b68)
[ 31.982100] 7b20: e9d4bd8000000cc0000000cf00000000e9d4bd80c1f3895800000cc0c1f38960
[ 31.990234] 7b40: 00000001000000cf00000004e9dc080000000000e8167b70c0f478ecc0f46d94
[ 31.998363] 7b60: 60070013ffffffff
[ 32.001833] [<c0301a8c>] (__irq_svc) from [<c0f46d94>] (netlink_trim+0x18/0xd8)
[ 32.009104] [<c0f46d94>] (netlink_trim) from [<c0f478ec>] (netlink_broadcast_filtered+0x34/0x414)
[ 32.017930] [<c0f478ec>] (netlink_broadcast_filtered) from [<c0f47cec>] (netlink_broadcast+0x20/0x28)
[ 32.027102] [<c0f47cec>] (netlink_broadcast) from [<c0eea378>] (rtnetlink_send+0x34/0x88)
[ 32.035238] [<c0eea378>] (rtnetlink_send) from [<c0f25890>] (notify_and_destroy+0x2c/0x44)
[ 32.043461] [<c0f25890>] (notify_and_destroy) from [<c0f25e08>] (qdisc_graft+0x398/0x470)
[ 32.051595] [<c0f25e08>] (qdisc_graft) from [<c0f27a00>] (tc_modify_qdisc+0x3a4/0x724)
[ 32.059470] [<c0f27a00>] (tc_modify_qdisc) from [<c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec)
[ 32.067864] [<c0ee4c84>] (rtnetlink_rcv_msg) from [<c0f4a988>] (netlink_rcv_skb+0xb8/0x110)
[ 32.076172] [<c0f4a988>] (netlink_rcv_skb) from [<c0f4a170>] (netlink_unicast+0x1b4/0x22c)
[ 32.084392] [<c0f4a170>] (netlink_unicast) from [<c0f4a5e4>] (netlink_sendmsg+0x33c/0x380)
[ 32.092614] [<c0f4a5e4>] (netlink_sendmsg) from [<c0ea9f40>] (sock_sendmsg+0x14/0x24)
[ 32.100403] [<c0ea9f40>] (sock_sendmsg) from [<c0eaa780>] (___sys_sendmsg+0x214/0x228)
[ 32.108279] [<c0eaa780>] (___sys_sendmsg) from [<c0eabad0>] (__sys_sendmsg+0x50/0x8c)
[ 32.116068] [<c0eabad0>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[ 32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0)
[ 32.128960] 7fa0: b6fa68c8000000f800000003bea142d00000000000000000
[ 32.137093] 7fc0: b6fa68c8000000f80052154c000001285d6468a2000000000000002800558c9c
[ 32.145224] 7fe0: 00000070bea1427800530d64b6e17e64
[ 32.150659] ---[ end trace 2139c9827c3e5177 ]---
This happens because the qdisc ->dequeue callback gets called. Which
again is not illegal, the qdisc will dequeue even when the interface is
up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames
will be dropped further down the stack in dev_direct_xmit().
And, at the end of the day, for what? For calculating the initial budget
of an interface which is non-operational at the moment and where frames
will get dropped anyway.
So if we can't figure out the link speed, default to SPEED_10 and move
along. We can also remove the runtime check now.
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com> Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 30 Aug 2019 01:07:21 +0000 (04:07 +0300)]
taprio: Fix kernel panic in taprio_destroy
taprio_init may fail earlier than this line:
list_add(&q->taprio_list, &taprio_list);
i.e. due to the net device not being multi queue.
Attempting to remove q from the global taprio_list when it is not part
of it will result in a kernel panic.
Fix it by matching list_add and list_del better to one another in the
order of operations. This way we can keep the deletion unconditional
and with lower complexity - O(1).
Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com> Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 31 Aug 2019 20:32:30 +0000 (13:32 -0700)]
Merge branch 'qed-Enhancements'
Sudarsana Reddy Kalluru says:
====================
qed*: Enhancements.
The patch series adds couple of enhancements to qed/qede drivers.
- Support for dumping the config id attributes via ethtool -w/W.
- Support for dumping the GRC data of required memory regions using
ethtool -w/W interfaces.
Patch (1) adds driver APIs for reading the config id attributes.
Patch (2) adds ethtool support for dumping the config id attributes.
Patch (3) adds support for configuring the GRC dump config flags.
Patch (4) adds ethtool support for dumping the grc dump.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver support for configuring grc dump config flags, and
dumping the grc data via ethtool get/set-dump interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log