Dan Carpenter [Thu, 4 Apr 2019 08:56:51 +0000 (11:56 +0300)]
ath6kl: add some bounds checking
The "ev->traffic_class" and "reply->ac" variables come from the network
and they're used as an offset into the wmi->stream_exist_for_ac[] array.
Those variables are u8 so they can be 0-255 but the stream_exist_for_ac[]
array only has WMM_NUM_AC (4) elements. We need to add a couple bounds
checks to prevent array overflows.
I also modified one existing check from "if (traffic_class > 3) {" to
"if (traffic_class >= WMM_NUM_AC) {" just to make them all consistent.
Fixes: bdcd81707973 (" Add ath6kl cleaned up driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad92 ("ath10k: support for multicast rate control") Co-developed-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Tested-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Fri, 26 Apr 2019 06:41:11 +0000 (09:41 +0300)]
ath10k: enable QCA6174 hw3.2 SDIO hardware
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.
Also tone down the warning about SDIO being not ready yet.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Fri, 26 Apr 2019 06:41:10 +0000 (09:41 +0300)]
ath10k: add fragmentation handler for high latency devices
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Fri, 26 Apr 2019 06:41:09 +0000 (09:41 +0300)]
ath10k: add PN replay protection for high latency devices
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Fri, 26 Apr 2019 06:41:07 +0000 (09:41 +0300)]
ath10k: add struct for high latency PN replay protection
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Fri, 19 Apr 2019 07:28:56 +0000 (10:28 +0300)]
ath10k: fix use-after-free on SDIO data frames
With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().
To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org>. Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kalle Valo [Fri, 19 Apr 2019 07:28:52 +0000 (10:28 +0300)]
ath10k: initialise struct ath10k_bus params to zero
This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Alagu Sankar <alagusankar@silex-india.com> Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong [Fri, 19 Apr 2019 07:28:47 +0000 (10:28 +0300)]
ath10k: don't disable interrupts in ath10k_sdio_remove()
Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.
Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patchset adds support for a PHY reset driven by a reset-controller.
Currently, only GPIO driven resets are supported by the PHY subsystem.
It also renames the reset-gpio from 'reset' to 'reset_gpio' to
better differentiate between resets wired to a GPIO and resets wired to
a reset-controller driven pin.
Some systems have the PHY reset-line wired to a pin controlled by a
reset-controller (eg. some Atheros AR9132 based boards). In case the
bootloader asserts reset before loading the kernel, we currently do not
have a clean way of deasserting reset to probe the PHY.
v3:
- add missing newline in mdio_bus.c
v2:
- fixed missed rename of "reset" in at803x.c
- move initial reset to mdio_device_reset
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:59 +0000 (13:51 -0700)]
net: skb: remove unused asserts
We are discouraging the use of BUG() these days, remove the
unused ASSERT macros from skbuff.h.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:58 +0000 (13:51 -0700)]
net: gemini: remove unnecessary assert
The driver does not advertize NETIF_F_FRAGLIST, the stack can't
pass skbs with frags lists to the xmit function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:57 +0000 (13:51 -0700)]
net/sched: taprio: fix build without 64bit div
Recent changes to taprio did not use the correct div64 helpers,
leading to:
net/sched/sch_taprio.o: In function `taprio_dequeue':
sch_taprio.c:(.text+0x34a): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `advance_sched':
sch_taprio.c:(.text+0xa0b): undefined reference to `__divdi3'
net/sched/sch_taprio.o: In function `taprio_init':
sch_taprio.c:(.text+0x1450): undefined reference to `__divdi3'
/home/jkicinski/devel/linux/Makefile:1032: recipe for target 'vmlinux' failed
Use math64 helpers.
Fixes: 7b9eba7ba0c1 ("net/sched: taprio: fix picos_per_byte miscalculation") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:56 +0000 (13:51 -0700)]
sb1000: fix variable set but not used warnings
GCC 8 complains:
drivers/net/sb1000.c: In function ‘card_send_command’:
drivers/net/sb1000.c:319:14: warning: variable ‘x’ set but not used [-Wunused-but-set-variable]
int status, x;
^
drivers/net/sb1000.c: In function ‘sb1000_check_CRC’:
drivers/net/sb1000.c:493:6: warning: variable ‘crc’ set but not used [-Wunused-but-set-variable]
int crc, status;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 17 Apr 2019 20:51:55 +0000 (13:51 -0700)]
l2tp: fix set but not used variable
GCC complains:
net/l2tp/l2tp_ppp.c: In function ‘pppol2tp_ioctl’:
net/l2tp/l2tp_ppp.c:1073:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
int val;
^~~
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.
There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().
Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.
v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
isn't defined, expand the description in ip-sysctl.txt and remove
unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
pointer to it is needed because of the way proc_do_large_bitmap work.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device_create() we set phydev->autoneg = 1. This isn't changed
even if the PHY doesn't support autoneg. This seems to affect very
few PHY's, and they disable phydev->autoneg in their config_init
callback. So it's more of an improvement, therefore net-next.
The patch also wouldn't apply to older kernel versions because the
link mode bitmaps have been introduced recently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 18 Apr 2019 18:25:33 +0000 (11:25 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-04-18
This series contains updates to the ice driver only.
Anirudh fixes up code comments which had typos. Added support for DCB
into the ice driver, which required a bit of refactoring of the existing
code. Also fixed a potential race condition between closing and opening
the VSI for a MIB change event, so resolved this by grabbing the
rtnl_lock prior to closing. Added support to process LLDP MIB change
notifications. Added support for reporting DCB stats via ethtool.
Brett updates the calculation to increment ITR to use a direct
calculation instead of using estimations. This provides a more accurate
value.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Brett Creeley [Thu, 28 Feb 2019 23:25:47 +0000 (15:25 -0800)]
ice: Calculate ITR increment based on direct calculation
Currently when calculating how much to increment ITR by inside of
ice_update_itr() we do some estimations and intermediate
calculations. Instead of doing estimations, just do the
calculation directly. This allows for a more accurate value and it
makes it easier for the next person to understand and update.
Also, remove the dividing the ITR value by 2 when latency
driven because the ITR values are already so low for 100Gbps
speed. This should help get to the desired ITR value faster.
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.
This patch requires a bit of a refactor of existing code.
1. For a MIB change event, the associated VSI is closed and brought up
again. The gap between closing and opening the VSI can cause a race
condition. Fix this by grabbing the rtnl_lock prior to closing the
VSI and then only free it after re-opening the VSI during a MIB
change event.
2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
unset. This results in namespace warnings (ice_sched.o: Externally
defined symbols with no external references) when CONFIG_DCB is unset.
To avoid this move ice_sched_query_elem from ice_sched.c to
ice_common.c.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.
This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.
In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Larry Finger [Wed, 17 Apr 2019 00:35:47 +0000 (19:35 -0500)]
rtlwifi: rtl8188ee: Remove extraneous file
Somehow file drivers/net/wireless/realtek/rtlwifi/rtl8188ee/trx.c.rej was
incorporated into the sources. Obviously, it can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Reported-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
David Ahern [Wed, 17 Apr 2019 00:31:43 +0000 (17:31 -0700)]
net ipv6: Prevent neighbor add if protocol is disabled on device
Disabling IPv6 on an interface removes existing entries but nothing prevents
new entries from being manually added. To that end, add a new neigh_table
operation, allow_add, that is called on RTM_NEWNEIGH to see if neighbor
entries are allowed on a given device. If IPv6 is disabled on the device,
allow_add returns false and passes a message back to the user via extack.
$ echo 1 > /proc/sys/net/ipv6/conf/eth1/disable_ipv6
$ ip -6 neigh add fe80::4c88:bff:fe21:2704 dev eth1 lladdr de:ad:be:ef:01:01
Error: IPv6 is disabled on this device.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
ipv6: Use fib6_result for fib_lookups
Add fib6_result as a single data structure to hold results from a fib
lookup. IPv6 currently has everything in 1 data structure - a fib6_info,
but with nexthop objects the fib6_nh can be in a nexthop or a nexthop
can be a blackhole which affects the fib6_type and flags (REJECT).
v2
- fixed 2 bugs in patch12:
i. checking return from fib6_table_lookup in fib6_lookup
ii. call to fib6_rule_saddr in fib6_rule_action_alt should use res->nh
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:11 +0000 (14:36 -0700)]
ipv6: Add fib6_type and fib6_flags to fib6_result
Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:05 +0000 (14:36 -0700)]
ipv6: Pass fib6_result to rt6_insert_exception
Update rt6_insert_exception to take a fib6_result over a fib6_info.
Change ort to f6i from the fib6_result and rename to better reflect
what it references (a fib6_info).
Since this function is already getting changed, update the comments
to reference fib6_info variables rather than the older rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:36:00 +0000 (14:36 -0700)]
ipv6: Pass fib6_result to rt6_find_cached_rt
Simplify rt6_find_cached_rt for the fast path cases and pass fib6_result
to rt6_find_cached_rt. Rename the local return variable to ret to maintain
consisting with fib6_result name.
Update the comment in rt6_find_cached_rt to reference the new names in
a fib6_info vs the old name when fib entries were an rt6_info.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 16 Apr 2019 21:35:59 +0000 (14:35 -0700)]
ipv6: Rename fib6_multipath_select and pass fib6_result
Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.
Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.
Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.
This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: stop/wake TX queues based on their fill level
Current xmit code only stops the txq after attempting to fill an
IO buffer that hasn't been TX-completed yet. In many-connection
scenarios, this can result in frequent rejected TX attempts, requeuing
of skbs with NETDEV_TX_BUSY and extra overhead.
Now that we have a proper 1-to-1 relation between stack-side txqs and
our HW Queues, overhaul the stop/wake logic so that the xmit code
stops the txq as needed.
Given that we might map multiple skbs into a single buffer, it's crucial
to ensure that the queue always provides an _entirely_ empty IO buffer.
Otherwise large skbs (eg TSO) might not fit into the last available
buffer. So whenever qeth_do_send_packet() first utilizes an _empty_
buffer, it updates & checks the used_buffers count.
This now ensures that an skb passed to qeth_xmit() can always be mapped
into an IO buffer, so remove all of the -EBUSY roll-back handling in the
TX path. We preserve the minimal safety-checks ("Is this IO buffer
really available?"), just in case some nasty future bug ever attempts to
corrupt an in-use buffer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: add TX multiqueue support for OSA devices
This adds trivial support for multiple TX queues on OSA-style devices
(both real HW and z/VM NICs). For now we expose the driver's existing
QoS mechanism via .ndo_select_queue, and adjust the number of available
TX queues when qeth_update_from_chp_desc() detects that the
HW configuration has changed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: add TX multiqueue support for IQD devices
qeth has been supporting multiple HW Output Queues for a long time. But
rather than exposing those queues to the stack, it uses its own queue
selection logic in .ndo_start_xmit... with all the drawbacks that
entails.
Start off by switching IQD devices over to a proper mqs net_device,
and converting all the netdev_queue management code.
One oddity with IQD devices is the requirement to place all mcast
traffic on the _highest_ established HW queue. Doing so via
.ndo_select_queue seems straight-forward - but that won't work if only
some of the HW queues are active
(ie. when dev->real_num_tx_queues < dev->num_tx_queues), since
netdev_cap_txqueue() will not allow us to put skbs on the higher queues.
To make this work, we
1. let .ndo_select_queue() map all mcast traffic to netdev_queue 0, and
2. later re-map the netdev_queue and HW queue indices in
.ndo_start_xmit and the TX completion handler.
With this patch we default to a fixed set of 1 ucast and 1 mcast queue.
Support for dynamic reconfiguration is added at a later time.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
struct netdev_queue contains a counter for tx timeouts, which gets
updated by dev_watchdog(). So let's not attempt to maintain our own
statistics, in particular not by overloading the skb-error counter.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
As the documentation for netif_trans_update() says, netdev_start_xmit()
already updates the last-tx time after every good xmit. So don't
duplicate that effort.
One odd case is that qeth_flush_buffers() also gets called from our
TX completion handler, to flush out any partially filled buffer when
we switch the queue to non-packing mode. But as the TX completion
handler will _always_ wake the txq, we don't have to worry about
the TX watchdog there.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
s390/qeth: handle error from qeth_update_from_chp_desc()
Subsequent code relies on the values that qeth_update_from_chp_desc()
reads from the CHP descriptor. Rather than dealing with weird errors
later on, just handle it properly here.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 17 Apr 2019 17:31:21 +0000 (10:31 -0700)]
Merge branch '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-04-16
This series contains updates to i40e driver only.
Adam fixes i40e so that queues can be restored to its original value if
configuring queue channels fails. Bumped the maximum API version
supported and added the API version to error messages to clarify
supported firmware API versions. Fixed the problem with the driver
being able to add only 7 multicast MAC address filters instead of 16.
Aleksandr adds support for Dynamic Device Personalization (DDP) which
allows loading profiles that change the way internal parser interprets
processed frames.
Nick fixes an issue where if we modify the VLAN stripping options when a
port VLAN is configured, it will break traffic for the VSI, so prevent
changes from being made.
Jake fixes an issue where a device reset can mess up the clock time
because we reset the clock time based on the kernel time every reset.
This causes us to potentially completely reset the PTP time, and can
cause unexpected behavior in programs like ptp4l.
Piotr fixes an LED blink issue with the 'ethtool -p' command, so that
identification blinking will work on all hardware.
Chinh fixed the error returned to correctly reflect the current state
when LLDP or DCBx is not in an operational state.
Grzegorz cleans up a misleading error message when untrusted VF tries to
exceed addresses beyond the NIC limit.
Carolyn fixes the error return code to correctly reflect the error case.
v2: updated the URL provided in the DDP patch (#2)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Fixes for some bugs cause by recent changes. One crash if you feed bad
data to the module parameters, one BUG that sometimes occurs when a
user closes the connection, and one bug that cause the driver to not
work if the configuration information only comes in from SMBIOS"
* tag 'for-linus-5.1-2' of git://github.com/cminyard/linux-ipmi:
ipmi: fix sleep-in-atomic in free_user at cleanup SRCU user->release_barrier
ipmi: ipmi_si_hardcode.c: init si_type array to fix a crash
ipmi: Fix failure on SMBIOS specified devices
Jose Abreu [Wed, 17 Apr 2019 07:33:05 +0000 (09:33 +0200)]
net: stmmac: Set Flow Control to automatic mode in the driver
By default Flow Control feature is not being enabled in stmmac.
This is a useful feature that can prevent loss of packets and now that
XGMAC already supports it (along with GMAC and QoS) it makes sense to
activate it.
Switch the module parameter to FLOW_AUTO so that Flow Control is
activated.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Wed, 17 Apr 2019 07:33:04 +0000 (09:33 +0200)]
net: stmmac: dwxgmac: Finish the Flow Control implementation
Finish the implementation of Flow Control feature. In order for it to
work correctly we need to set EHFC bit and the correct threshold values
for activating and deactivating it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com> Cc: Joao Pinto <jpinto@synopsys.com> Cc: David S. Miller <davem@davemloft.net> Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com> Cc: Alexandre Torgue <alexandre.torgue@st.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the new socket options only work correctly
for native execution, but in case of compat mode fall back
to the old behavior as we ignore the 'old_timeval' flag.
Rework so we treat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW the
same way in compat and native 32-bit mode.
Cc: Deepa Dinamani <deepa.kernel@gmail.com> Fixes: a9beb86ae6e5 ("sock: Add SO_RCVTIMEO_NEW and SO_SNDTIMEO_NEW") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 16 Apr 2019 17:55:20 +0000 (10:55 -0700)]
tcp: tcp_grow_window() needs to respect tcp_space()
For some reason, tcp_grow_window() correctly tests if enough room
is present before attempting to increase tp->rcv_ssthresh,
but does not prevent it to grow past tcp_space()
This is causing hard to debug issues, like failing
the (__tcp_select_window(sk) >= tp->rcv_wnd) test
in __tcp_ack_snd_check(), causing ACK delays and possibly
slow flows.
Depending on tcp_rmem[2], MTU, skb->len/skb->truesize ratio,
we can see the problem happening on "netperf -t TCP_RR -- -r 2000,2000"
after about 60 round trips, when the active side no longer sends
immediate acks.
This bug predates git history.
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
dpaa2-eth: Add flow steering support without masking
On DPAA2 platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't offer
flow steering capabilities at all on these platforms.
Introduce a limited support for flow steering, where we only
allow ethtool rules that share a common key (i.e. have the same
header fields). If a rule with a new composition key is wanted,
the user must first manually delete all previous rules.
First patch fixes a minor bug, the next two cleanup and prepare
the code and the last one introduces the actual FS support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dpaa2-eth: Add flow steering support without masking
On platforms that lack a TCAM (like LS1088A), masking of
flow steering keys is not supported. Until now we didn't
offer flow steering capabilities at all on these platforms,
since our driver implementation configured a "comprehensive"
FS key (containing all supported header fields), with masks
used to ignore the fields not present in the rules provided
by the user.
We now allow ethtool rules that share a common key (i.e. have
the same header fields). The FS key is now kept in the driver
private data and initialized when the first rule is added to
an empty table, rather than at probe time. If a rule with a new
composition key is wanted, the user must first manually delete
all previous rules.
When building a FS table entry to pass to firmware, we still use
the old building algorithm, which assumes an all-supported-fields
key, and later collapse the fields which aren't actually needed.
Masked rules are not supported; if provided, the mask value
will be ignored. For firmware versions older than MC10.7.0
(that only offer the legacy ABIs for configuring distribution
keys) flow steering without masking support remains unavailable.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an internal id bitfield to uniquely identify header fields
supported by the Rx distribution keys. For the hash key, add a
conversion from the RXH_* bitmask provided by ethtool to the internal
ids.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This is preventive cleanup that may save troubles later.
No need to cancel repeateadly queued work if code is properly
refactored.
Don't let the ethtool -s process interfere with the stat workqueue
scheduling.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley [Tue, 16 Apr 2019 14:04:23 +0000 (15:04 +0100)]
nfp: flower: fix implicit fallthrough warning
The nfp_flower_copy_pre_actions function introduces a case statement with
an intentional fallthrough. However, this generates a warning if built
with the -Wimplicit-fallthrough flag.
Remove the warning by adding a fall through comment.
Fixes: 1c6952ca587d ("nfp: flower: generate merge flow rule") Signed-off-by: John Hurley <john.hurley@netronome.com> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Reviewed-by: Jiong Wang <jiong.wang@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: bridge: fix netlink export of vlan_stats_per_port option
Since the introduction of the vlan_stats_per_port option the netlink
export of it has been broken since I made a typo and used the ifla
attribute instead of the bridge option to retrieve its state.
Sysfs export is fine, only netlink export has been affected.
Fixes: 9163a0fc1f0c0 ("net: bridge: add support for per-port vlan stats") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 16 Apr 2019 11:43:17 +0000 (12:43 +0100)]
qed: fix spelling mistake "faspath" -> "fastpath"
There is a spelling mistake in a DP_INFO message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart [Tue, 16 Apr 2019 10:10:20 +0000 (12:10 +0200)]
net: phy: micrel: add Asym Pause workaround
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
bnx2x: Support for timestamping in P2P mode.
The patch series adds driver support for timestamping the ptp packets
in peer-delay (P2P) mode.
- Patch (1) performs the code cleanup.
- Patch (2) adds the required implementation.
Please consider applying it 'net-next' tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Add support for detection of P2P event packets.
The patch adds support for detecting the P2P (peer-to-peer) event packets.
This is required for timestamping the PTP packets in peer delay mode.
Unmask the below bits (set to 0) for device to detect the p2p packets.
NIG_REG_P0/1_LLH_PTP_PARAM_MASK
NIG_REG_P0/1_TLLH_PTP_PARAM_MASK
bit 1 - IPv4 DA 1 of 224.0.0.107.
bit 3 - IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
NIG_REG_P0/1_LLH_PTP_RULE_MASK
NIG_REG_P0/1_TLLH_PTP_RULE_MASK
bit 2 - {IPv4 DA 1; UDP DP 0}
bit 6 - MAC Ethertype 0 of 0x88F7.
bit 9 - MAC DA 1 of 0x01-80-C2-00-00-0E.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x: Replace magic numbers with macro definitions.
This patch performs code cleanup by defining macros for the ptp-timestamp
filters.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jie Liu [Tue, 16 Apr 2019 05:10:09 +0000 (13:10 +0800)]
tipc: set sysctl_tipc_rmem and named_timeout right range
We find that sysctl_tipc_rmem and named_timeout do not have the right minimum
setting. sysctl_tipc_rmem should be larger than zero, like sysctl_tcp_rmem.
And named_timeout as a timeout setting should be not less than zero.
Fixes: cc79dd1ba9c10 ("tipc: change socket buffer overflow control to respect sk_rcvbuf") Fixes: a5325ae5b8bff ("tipc: add name distributor resiliency queue") Signed-off-by: Jie Liu <liujie165@huawei.com> Reported-by: Qiang Ning <ningqiang1@huawei.com> Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Reviewed-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
According to the link FSM, when a link endpoint got RESET_MSG (- a
traditional one without the stopping bit) from its peer, it moves to
PEER_RESET state and raises a LINK_DOWN event which then resets the
link itself. Its state will become ESTABLISHING after the reset event
and the link will be re-established soon after this endpoint starts to
send ACTIVATE_MSG to the peer.
There is no problem with this mechanism, however the link resetting has
cleared the link 'in_session' flag (along with the other important link
data such as: the link 'mtu') that was correctly set up at the 1st step
(i.e. when this endpoint received the peer RESET_MSG). As a result, the
link will become ESTABLISHED, but the 'in_session' flag is not set, and
all STATE_MSG from its peer will be dropped at the link_validate_msg().
It means the link not synced and will sooner or later face a failure.
Since the link reset action is obviously needed for a new link session
(this is also true in the other situations), the problem here is that
the link is re-established a bit too early when the link endpoints are
not really in-sync yet. The commit forces a resync as already done in
the previous commit 91986ee166cf ("tipc: fix link session and
re-establish issues") by simply varying the link 'peer_session' value
at the link_reset().
Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Fix missing meta data in skb with vlan packet
skb_reorder_vlan_header() should move XDP meta data with ethernet header
if XDP meta data exists.
Fixes: de8f3a83b0a0 ("bpf: add meta pointer for direct access") Signed-off-by: Yuya Kusakabe <yuya.kusakabe@gmail.com> Signed-off-by: Takeru Hayasaka <taketarou2@gmail.com> Co-developed-by: Takeru Hayasaka <taketarou2@gmail.com> Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>