Steve French [Fri, 13 Apr 2018 01:32:13 +0000 (20:32 -0500)]
smb3.11: replace a 4 with server->vals->header_preamble_size
More cleanup of use of hardcoded 4 byte RFC1001 field size
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Merge branch 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
- fix panic when halting system via "shutdown -h now"
- drop own coding in favour of generic CONFIG_COMPAT_BINFMT_ELF
implementation
- add FPE_CONDTRAP constant: last outstanding parisc-specific cleanup
for Eric Biedermans siginfo patches
- move some functions to .init and some to .text.hot linker sections
* 'parisc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent panic at system halt
parisc: Switch to generic COMPAT_BINFMT_ELF
parisc: Move cache flush functions into .text.hot section
parisc/signal: Add FPE_CONDTRAP for conditional trap handling
On SuperH, the base of the physical memory might be different from
zero. In this case, PCI address zero will map to a non-zero physical
address. In order to make sure that the DMA mapping API takes care of
this DMA offset, we must fill in the dev->dma_pfn_offset field for PCI
devices. This gets done in the pcibios_bus_add_device() hook, called
for each new PCI device detected.
The dma_pfn_offset global variable is re-calculated for every PCI
controller available on the platform, but that's not an issue because
its value will each time be exactly the same, as it only depends on
the memory start address and memory size.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
The code setting up the PCI -> SuperHighway mapping doesn't take into
account the fact that the address stored in PCIELARx must be aligned
with the size stored in PCIELAMRx.
For example, when your physical memory starts at 0x0800_0000 (128 MB),
a size of 64 MB or 128 MB is fine. However, if you have 256 MB of
memory, it doesn't work because the base address is not aligned on the
size.
In such situation, we have to round down the base address to make sure
it is aligned on the size of the area. For for a 0x0800_0000 base
address with 256 MB of memory, we will round down to 0x0, and extend
the size of the mapping to 512 MB.
This allows the mapping to work on platforms that have 256 MB of
RAM. The current setup would only work with 128 MB of RAM or less.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
arch/sh: pcie-sh7786: adjust PCI MEM and IO regions
The current definition of the PCIe IO and MEM resources for SH7786
doesn't match what the datasheet says. For example, for PCIe0
0xfe100000 is advertised by the datasheet as a PCI IO region, while
0xfd000000 is advertised as a PCI MEM region. The code currently
inverts the two.
The SH4A_PCIEPARL and SH4A_PCIEPTCTLR registers allow to define the
base address and role of the different regions (including whether it's
a MEM or IO region). However, practical experience on a SH7786 shows
that if 0xfe100000 is used for LEL and 0xfd000000 for IO, a PCIe
device using two MEM BARs cannot be accessed at all. Simply using
0xfe100000 for IO and 0xfd000000 for MEM makes the PCIe device
accessible.
It is very likely that this was never seen because there are two other
PCI MEM region listed in the resources. However, for different
reasons, none of the two other MEM regions are usable on the specific
SH7786 platform the problem was encountered. Therefore, the last MEM
region at 0xfe100000 was used to place the BARs, making the device
non-functional.
This commit therefore adjusts those PCI MEM and IO resources
definitions so that they match what the datasheet says. They have only
been tested with PCIe 0.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
arch/sh: pcie-sh7786: exclude unusable PCI MEM areas
Depending on the physical memory layout, some PCI MEM areas are not
usable. According to the SH7786 datasheet, the PCI MEM area from
1000_0000 to 13FF_FFFF is only usable if the physical memory layout
(in MMSELR) is 1, 2, 5 or 6. In all other configurations, this PCI MEM
area is not usable (because it overlaps with DRAM).
Therefore, this commit adjusts the PCI SH7786 initialization to mark
the relevant PCI resource as IORESOURCE_DISABLED if we can't use it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
arch/sh: pcie-sh7786: mark unavailable PCI resource as disabled
Some PCI MEM resources are marked as IORESOURCE_MEM_32BIT, which means
they are only usable when the SH core runs in 32-bit mode. In 29-bit
mode, such memory regions are not usable.
The existing code for SH7786 properly skips such regions when
configuring the PCIe controller registers. However, because such
regions are still described in the resource array, the
pcibios_scanbus() function in the SuperH pci.c will register them to
the PCI core. Due to this, the PCI core will allocate MEM areas from
this resource, and assign BARs pointing to this area, even though it's
unusable.
In order to prevent this from happening, we mark such regions as
IORESOURCE_DISABLED, which tells the SuperH pci.c pcibios_scanbus()
function to skip them.
Note that we separate marking the region as disabled from skipping it,
because other regions will be marked as disabled in follow-up patches.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
In pcibios_scanbus(), we provide to the PCI core the usable MEM and IO
regions using pci_add_resource_offset(). We travel through all
resources available in the "struct pci_channel".
Also, in register_pci_controller(), we travel through all resources to
request them, making sure they don't conflict with already requested
resources.
However, some resources may be disabled, in which case they should not
be requested nor provided to the PCI core.
In the current situation, none of the resources are disabled. However,
follow-up patches in this series will make some resources disabled,
making this preliminary change necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
arch/sh: make the DMA mapping operations observe dev->dma_pfn_offset
Some devices may have a non-zero DMA offset, i.e an offset between the
DMA address and the physical address. Such an offset can be encoded
into the dma_pfn_offset field of "struct device", but the SuperH
implementation of the DMA mapping API does not observe this
information.
This commit fixes that by ensuring the DMA address is properly
calculated depending on this DMA offset.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
The SH7786 has different physical memory layout configurations,
configurable through the MMSELR register. The configuration is
typically defined by the bootloader, so Linux generally doesn't care.
Except that depending on the configuration, some PCI MEM areas may or
may not be available. This commit adds a helper function that allows
to retrieve the current physical memory layout configuration. It will
be used in a following patch to exclude unusable PCI MEM areas during
the PCI initialization.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Rich Felker <dalias@libc.org>
Rich Felker [Fri, 16 Mar 2018 00:01:36 +0000 (20:01 -0400)]
sh: fix debug trap failure to process signals before return to user
When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.
sh: fix memory corruption of unflattened device tree
unflatten_device_tree() makes use of memblock allocation, and
therefore must be called before paging_init() migrates the memblock
allocation data to the bootmem framework. Otherwise the record of the
allocation for the expanded device tree will be lost, and will
eventually be clobbered when allocated for another use.
Aurelien Jarno [Tue, 2 May 2017 13:00:12 +0000 (13:00 +0000)]
sh: fix futex FUTEX_OP_SET op on userspace addresses
Commit 00b73d8d1b71 ("sh: add working futex atomic ops on userspace
addresses for smp") changed the futex_atomic_op_inuser function to
use a loop. In case of the FUTEX_OP_SET op with a userspace address
containing a value different of 0, this loop is an endless loop.
Fix that by loading the value of oldval from the userspace before doing
the cmpxchg op, also for the FUTEX_OP_SET case.
Dave Airlie [Thu, 12 Apr 2018 23:25:21 +0000 (09:25 +1000)]
Merge branch 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux into drm-next
- Add a PX quirk for radeon
- Fix flickering and stability issues with DC on some platforms
- Fix HDMI audio regression
- Few other misc DC and base driver fixes
* 'drm-next-4.17' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/amd/display: disable CRTCs with NULL FB on their primary plane (V2)"
Revert "drm/amd/display: fix dereferencing possible ERR_PTR()"
drm/amd/display: Fix regamma not affecting full-intensity color values
drm/amd/display: Fix FBC text console corruption
drm/amd/display: Only register backlight device if embedded panel connected
drm/amd/display: fix brightness level after resume from suspend
drm/amd/display: HDMI has no sound after Panel power off/on
drm/amdgpu: add MP1 and THM hw ip base reg offset
drm/amdgpu: fix null pointer panic with direct fw loading on gpu reset
drm/radeon: add PX quirk for Asus K73TK
Dave Airlie [Thu, 12 Apr 2018 23:25:07 +0000 (09:25 +1000)]
Merge tag 'drm-misc-next-fixes-2018-04-11' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
omap: Fix crash on AM4 EVM, and all OMAP2/3 boards (Tomi)
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
* tag 'drm-misc-next-fixes-2018-04-11' of git://anongit.freedesktop.org/drm/drm-misc:
drm/omap: fix crash if there's no video PLL
Ronnie Sahlberg [Mon, 9 Apr 2018 08:06:27 +0000 (18:06 +1000)]
cifs: replace a 4 with server->vals->header_preamble_size
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Ronnie Sahlberg [Mon, 9 Apr 2018 08:06:26 +0000 (18:06 +1000)]
cifs: add pdu_size to the TCP_Server_Info structure
and get rid of some get_rfc1002_length() in smb2
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Steve French [Mon, 9 Apr 2018 15:47:14 +0000 (10:47 -0500)]
SMB311: Improve checking of negotiate security contexts
SMB3.11 crypto and hash contexts were not being checked strictly enough.
Add parsing and validity checking for the security contexts in the SMB3.11
negotiate response.
Signed-off-by: Steve French <smfrench@gmail.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Steve French [Sun, 8 Apr 2018 21:14:31 +0000 (16:14 -0500)]
SMB3: Fix length checking of SMB3.11 negotiate request
The length checking for SMB3.11 negotiate request includes
"negotiate contexts" which caused a buffer validation problem
and a confusing warning message on SMB3.11 mount e.g.:
SMB2 server sent bad RFC1001 len 236 not 170
Fix the length checking for SMB3.11 negotiate to account for
the new negotiate context so that we don't log a warning on
SMB3.11 mount by default but do log warnings if lengths returned
by the server are incorrect.
CC: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Merge tag 'xfs-4.17-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull more xfs updates from Darrick Wong:
"Most of these are code cleanups, but there are a couple of notable
use-after-free bug fixes.
This series has been run through a full xfstests run over the week and
through a quick xfstests run against this morning's master, with no
major failures reported.
- clean up unnecessary function call parameters
- fix a use-after-free bug when aborting logging intents
- refactor filestreams state data to avoid use-after-free bug
- fix incorrect removal of cow extents when truncating extended
attributes.
- refactor open-coded __set_page_dirty in favor of using vfs
function.
- fix a deadlock when fstrim and fs shutdown race"
* tag 'xfs-4.17-merge-4' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
Force log to disk before reading the AGF during a fstrim
Export __set_page_dirty
xfs: only cancel cow blocks when truncating the data fork
xfs: non-scrub - remove unused function parameters
xfs: remove filestream item xfs_inode reference
xfs: fix intent use-after-free on abort
xfs: Remove "committed" argument of xfs_dir_ialloc
Merge tag 'gfs2-4.17.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2
Pull more gfs2 updates from Bob Peterson:
"We decided to request the latest three patches to be merged into this
merge window while it's still open.
- The first patch adds a new function to lockref:
lockref_put_not_zero
- The second patch fixes GFS2's glock dump code so it uses the new
lockref function. This fixes a problem whereby lock dumps could
miss glocks.
- I made a minor patch to update some comments and fix the lock
ordering text in our gfs2-glocks.txt Documentation file"
* tag 'gfs2-4.17.fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
GFS2: Minor improvements to comments and documentation
gfs2: Stop using rhashtable_walk_peek
lockref: Add lockref_put_not_zero
Other bugfixes and cleanups:
- Several other small NFSoRDMA cleanups
- Improvements to the sunrpc RTT measurements
- A few sunrpc tracepoint cleanups
- Various fixes for NFS v4 lock notifications
- Various sunrpc and NFS v4 XDR encoding cleanups
- Switch to the ida_simple API
- Fix NFSv4.1 exclusive create
- Forget acl cache after setattr operation
- Don't advance the nfs_entry readdir cookie if xdr decoding fails"
* tag 'nfs-for-4.17-1' of git://git.linux-nfs.org/projects/anna/linux-nfs: (47 commits)
NFS: advance nfs_entry cookie only after decoding completes successfully
NFSv3/acl: forget acl cache after setattr
NFSv4.1: Fix exclusive create
NFSv4: Declare the size up to date after it was set.
nfs: Use ida_simple API
NFSv4: Fix the nfs_inode_set_delegation() arguments
NFSv4: Clean up CB_GETATTR encoding
NFSv4: Don't ask for attributes when ACCESS is protected by a delegation
NFSv4: Add a helper to encode/decode struct timespec
NFSv4: Clean up encode_attrs
NFSv4; Clean up XDR encoding of type bitmap4
NFSv4: Allow GFP_NOIO sleeps in decode_attr_owner/decode_attr_group
SUNRPC: Add a helper for encoding opaque data inline
SUNRPC: Add helpers for decoding opaque and string types
NFSv4: Ignore change attribute invalidations if we hold a delegation
NFS: More fine grained attribute tracking
NFS: Don't force unnecessary cache invalidation in nfs_update_inode()
NFS: Don't redirty the attribute cache in nfs_wcc_update_inode()
NFS: Don't force a revalidation of all attributes if change is missing
NFS: Convert NFS_INO_INVALID flags to unsigned long
...
Merge branch 'work.thaw' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs thaw updates from Al Viro:
"An ancient series that has fallen through the cracks in the previous
cycle"
* 'work.thaw' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
buffer.c: call thaw_super during emergency thaw
vfs: factor sb iteration out of do_emergency_remount
Cc: Shirish S <shirish.s@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Merge branch 'afs-dh' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull AFS updates from Al Viro:
"The AFS series posted by dhowells depended upon lookup_one_len()
rework; now that prereq is in the mainline, that series had been
rebased on top of it and got some exposure and testing..."
* 'afs-dh' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
afs: Do better accretion of small writes on newly created content
afs: Add stats for data transfer operations
afs: Trace protocol errors
afs: Locally edit directory data for mkdir/create/unlink/...
afs: Adjust the directory XDR structures
afs: Split the directory content defs into a header
afs: Fix directory handling
afs: Split the dynroot stuff out and give it its own ops tables
afs: Keep track of invalid-before version for dentry coherency
afs: Rearrange status mapping
afs: Make it possible to get the data version in readpage
afs: Init inode before accessing cache
afs: Introduce a statistics proc file
afs: Dump bad status record
afs: Implement @cell substitution handling
afs: Implement @sys substitution handling
afs: Prospectively look up extra files when doing a single lookup
afs: Don't over-increment the cell usage count when pinning it
afs: Fix checker warnings
vfs: Remove the const from dir_context::actor
Cc: Shirish S <shirish.s@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm/amd/display: Fix regamma not affecting full-intensity color values
Hardware understands the regamma LUT as a piecewise linear function,
with points spaced exponentially along the range. We previously
programmed the LUT for range [2^-10, 2^0). This causes (normalized)
color values of 1 (=2^0) to miss the programmed LUT, and fall onto the
end region.
For DCE, the end region is extrapolated using a single (base, slope)
pair, using the max y-value from the last point in the curve as base.
This presents a problem, since this value affects all three color
channels. Scaling down the intensity of say - the blue regamma curve -
will not affect it's end region. This is especially noticiable when
using RedShift. It scales down the blue and green channels, but leaves
full-intensity colors unshifted.
Therefore, extend the range to cover [2^-10, 2^1) by programming another
hardware segment, containing only one point. That way, we won't be
hitting the end region.
Note that things are a bit different for DCN, since the end region can
be set per-channel.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com> Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Roman Li [Thu, 29 Mar 2018 15:14:25 +0000 (11:14 -0400)]
drm/amd/display: Fix FBC text console corruption
Signed-off-by: Roman Li <roman.li@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Harry Wentland [Mon, 12 Mar 2018 15:16:47 +0000 (11:16 -0400)]
drm/amd/display: Only register backlight device if embedded panel connected
Signed-off-by: Harry Wentland <harry.wentland@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1) In ip_gre tunnel, handle the conflict between TUNNEL_{SEQ,CSUM} and
GSO/LLTX properly. From Sabrina Dubroca.
2) Stop properly on error in lan78xx_read_otp(), from Phil Elwell.
3) Don't uncompress in slip before rstate is initialized, from Tejaswi
Tanikella.
4) When using 1.x firmware on aquantia, issue a deinit before we
hardware reset the chip, otherwise we break dirty wake WOL. From
Igor Russkikh.
5) Correct log check in vhost_vq_access_ok(), from Stefan Hajnoczi.
6) Fix ethtool -x crashes in bnxt_en, from Michael Chan.
7) Fix races in l2tp tunnel creation and duplicate tunnel detection,
from Guillaume Nault.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
l2tp: fix race in duplicate tunnel detection
l2tp: fix races in tunnel creation
tun: send netlink notification when the device is modified
tun: set the flags before registering the netdevice
lan78xx: Don't reset the interface on open
bnxt_en: Fix NULL pointer dereference at bnxt_free_irq().
bnxt_en: Need to include RDMA rings in bnxt_check_rings().
bnxt_en: Support max-mtu with VF-reps
bnxt_en: Ignore src port field in decap filter nodes
bnxt_en: do not allow wildcard matches for L2 flows
bnxt_en: Fix ethtool -x crash when device is down.
vhost: return bool from *_access_ok() functions
vhost: fix vhost_vq_access_ok() log check
vhost: Fix vhost_copy_to_user()
net: aquantia: oops when shutdown on already stopped device
net: aquantia: Regression on reset with 1.x firmware
cdc_ether: flag the Cinterion AHS8 modem by gemalto as WWAN
slip: Check if rstate is initialized before uncompressing
lan78xx: Avoid spurious kevent 4 "error"
lan78xx: Correctly indicate invalid OTP
...
Merge tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A few fixes of Xen related core code and drivers"
* tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Indicate XENFEAT_linux_rsdp_unrestricted to Xen
xen/acpi: off by one in read_acpi_id()
xen/acpi: upload _PSD info for non Dom0 CPUs too
x86/xen: Delay get_cpu_cap until stack canary is established
xen: xenbus_dev_frontend: Verify body of XS_TRANSACTION_END
xen: xenbus: Catch closing of non existent transactions
xen: xenbus_dev_frontend: Fix XS_TRANSACTION_END handling
Merge tag 'mmc-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Prevent bus reference leak in mmc_blk_init()
MMC host:
- tmio: Fix error handling when issuing CMD23
- jz4740: Fix race condition in IRQ mask update"
* tag 'mmc-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: tmio: Fix error handling when issuing CMD23
mmc: core: Prevent bus reference leak in mmc_blk_init()
mmc: jz4740: Fix race condition in IRQ mask update
Merge tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kdb updates from Jason Wessel:
- fix 2032 time access issues and new compiler warnings
- minor regression test cleanup
- formatting fixes for end user use of kdb
* tag 'for_linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kdb: use memmove instead of overlapping memcpy
kdb: use ktime_get_mono_fast_ns() instead of ktime_get_ts()
kdb: bl: don't use tab character in output
kdb: drop newline in unknown command output
kdb: make "mdr" command repeat
kdb: use __ktime_get_real_seconds instead of __current_kernel_time
misc: kgdbts: Display progress of asynchronous tests
Merge tag 'microblaze-4.17-rc1' of git://git.monstr.eu/linux-2.6-microblaze
Pull microblaze updates from Michal Simek:
"Use generic pci_mmap_resource_range()"
* tag 'microblaze-4.17-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Use generic pci_mmap_resource_range()
microblaze: Provide pgprot_device/writecombine macros for nommu
Function rhashtable_walk_peek is problematic because there is no
guarantee that the glock previously returned still exists; when that key
is deleted, rhashtable_walk_peek can end up returning a different key,
which will cause an inconsistent glock dump. Fix this by keeping track
of the current glock in the seq file iterator functions instead.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Put a lockref unless the lockref is dead or its count would become zero.
This is the same as lockref_put_or_lock except that the lock is never
left held.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Merge tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic fixes from Arnd Bergmann:
"I have one regression fix for a minor build problem after the
architecture removal series, plus a rework of the barriers in the
readl/writel functions, thanks to work by Sinan Kaya:
This started from a discussion on the linuxpcc and rdma mailing
lists[1]. To summarize, we decided that architectures are responsible
to serialize readl() and writel() accesses on a device MMIO space
relative to DMA performed by that device.
This series provides a pessimistic implementation of that behavior for
asm-generic/io.h, which is in turn used by a number of architectures
(h8300, microblaze, nios2, openrisc, s390, sparc, um, unicore32, and
xtensa). Some of those presumably need no extra barriers, or something
weaker than rmb()/wmb(), and they are advised to override the new
default for better performance.
For inb()/outb(), the same barriers are used, but architectures might
want to add another barrier to outb() here if that can guarantee
non-posted behavior (some architectures can, others cannot do that).
The readl_relaxed()/writel_relaxed() family of functions retains the
existing behavior with no extra barriers"
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
io: change writeX_relaxed() to remove barriers
io: change readX_relaxed() to remove barriers
dts: remove cris & metag dts hard link file
io: change inX() to have their own IO barrier overrides
io: change outX() to have their own IO barrier overrides
io: define stronger ordering for the default writeX() implementation
io: define stronger ordering for the default readX() implementation
io: define several IO & PIO barrier types for the asm-generic version
James Smart [Thu, 12 Apr 2018 15:16:15 +0000 (09:16 -0600)]
nvme: expand nvmf_check_if_ready checks
The nvmf_check_if_ready() checks that were added are very simplistic.
As such, the routine allows a lot of cases to fail ios during windows
of reset or re-connection. In cases where there are not multi-path
options present, the error goes back to the callee - the filesystem
or application. Not good.
The common routine was rewritten and calling syntax slightly expanded
so that per-transport is_ready routines don't need to be present.
The transports now call the routine directly. The routine is now a
fabrics routine rather than an inline function.
The routine now looks at controller state to decide the action to
take. Some states mandate io failure. Others define the condition where
a command can be accepted. When the decision is unclear, a generic
queue-or-reject check is made to look for failfast or multipath ios and
only fails the io if it is so marked. Otherwise, the io will be queued
and wait for the controller state to resolve.
Admin commands issued via ioctl share a live admin queue with commands
from the transport for controller init. The ioctls could be intermixed
with the initialization commands. It's possible for the ioctl cmd to
be issued prior to the controller being enabled. To block this, the
ioctl admin commands need to be distinguished from admin commands used
for controller init. Added a USERCMD nvme_req(req)->rq_flags bit to
reflect this division and set it on ioctls requests. As the
nvmf_check_if_ready() routine is called prior to nvme_setup_cmd(),
ensure that commands allocated by the ioctl path (actually anything
in core.c) preps the nvme_req(req) before starting the io. This will
preserve the USERCMD flag during execution and/or retry.
Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.e> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Daniel Verkamp [Thu, 12 Apr 2018 15:16:13 +0000 (09:16 -0600)]
nvmet: fix space padding in serial number
Commit 42de82a8b544 previously attempted to fix this, and it did
correctly pad the MN and FR fields with spaces, but the SN field still
contains 0 bytes. The current code fills out the first 16 bytes with
hex2bin, leaving the last 4 bytes zeroed. Rather than adding a lot of
error-prone math to avoid overwriting SN twice, just set the whole thing
to spaces up front (it's only 20 bytes).
Fixes: 42de82a8b544 ("nvmet: don't report 0-bytes in serial number") Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com> Reviewed-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch [Thu, 12 Apr 2018 15:16:10 +0000 (09:16 -0600)]
nvme-pci: Separate IO and admin queue IRQ vectors
The admin and first IO queues shared the first irq vector, which has an
affinity mask including cpu0. If a system allows cpu0 to be offlined,
the admin queue may not be usable if no other CPUs in the affinity mask
are online. This is a problem since unlike IO queues, there is only
one admin queue that always needs to be usable.
To fix, this patch allocates one pre_vector for the admin queue that
is assigned all CPUs, so will always be accessible. The IO queues are
assigned the remaining managed vectors.
In case a controller has only one interrupt vector available, the admin
and IO queues will share the pre_vector with all CPUs assigned.
Cc: Jianchao Wang <jianchao.w.wang@oracle.com> Cc: Ming Lei <ming.lei@redhat.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch [Thu, 12 Apr 2018 15:16:09 +0000 (09:16 -0600)]
nvme-pci: Remove unused queue parameter
All the queue memory is allocated up front. We don't take the node
into consideration when creating queues anymore, so removing the unused
parameter.
Signed-off-by: Keith Busch <keith.busch@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Keith Busch [Thu, 12 Apr 2018 15:16:08 +0000 (09:16 -0600)]
nvme-pci: Skip queue deletion if there are no queues
User reported controller always retains CSTS.RDY to 1, which fails
controller disabling when resetting the controller. This is also before
the admin queue is allocated, and trying to disable an unallocated queue
results in a NULL dereference.
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvmet_execute_get_disc_log_page() passes a fixed-length string into
nvmet_format_discovery_entry(), which then does a longer memcpy() on
it, as pointed out by gcc-8:
In function 'nvmet_format_discovery_entry',
inlined from 'nvmet_execute_get_disc_log_page' at drivers/nvme/target/discovery.c:126:4:
drivers/nvme/target/discovery.c:62:2: error: 'memcpy' forming offset [38, 223] is out of the bounds [0, 37] [-Werror=array-bounds]
memcpy(e->subnqn, subsys_nqn, NVMF_NQN_SIZE);
Using strncpy() will make this well-defined, filling the rest of the
buffer with zeroes, under the assumption that the input is either
a NUL-terminated string, or a byte sequence containing no zeroes.
If the input is a string that is longer than NVMF_NQN_SIZE, we
continue to have no NUL-termination in the output.
Fixes: a07b4970f464 ("nvmet: add a generic NVMe target") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
nvme: don't send keep-alives to the discovery controller
NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.
We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.
This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: 07bfcd09a288 ("nvme-fabrics: add a generic NVMe over Fabrics library") Reported-by: Martin George <marting@netapp.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ming Lei [Thu, 12 Apr 2018 15:16:04 +0000 (09:16 -0600)]
nvme-loop: fix kernel oops in case of unhandled command
When nvmet_req_init() fails, __nvmet_req_complete() is called
to handle the target request via .queue_response(), so
nvme_loop_queue_response() shouldn't be called again for
handling the failure.
This patch fixes this case by the following way:
- move blk_mq_start_request() before nvmet_req_init(), so
nvme_loop_queue_response() may work well to complete this
host request
- don't call nvme_cleanup_cmd() which is done in nvme_loop_complete_rq()
- don't call nvme_loop_queue_response() which is done via
.queue_response()
Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de>
[trimmed changelog] Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
David Sterba [Tue, 3 Apr 2018 17:23:33 +0000 (19:23 +0200)]
btrfs: replace GPL boilerplate by SPDX -- sources
Remove GPL boilerplate text (long, short, one-line) and keep the rest,
ie. personal, company or original source copyright statements. Add the
SPDX header.
David Sterba [Tue, 3 Apr 2018 17:16:55 +0000 (19:16 +0200)]
btrfs: replace GPL boilerplate by SPDX -- headers
Remove GPL boilerplate text (long, short, one-line) and keep the rest,
ie. personal, company or original source copyright statements. Add the
SPDX header.
Unify the include protection macros to match the file names.
Michael Ellerman [Thu, 12 Apr 2018 01:35:55 +0000 (11:35 +1000)]
powerpc/mm/radix: Fix checkstops caused by invalid tlbiel
In tlbiel_radix_set_isa300() we use the PPC_TLBIEL() macro to
construct tlbiel instructions. The instruction takes 5 fields, two of
which are registers, and the others are constants. But because it's
constructed with inline asm the compiler doesn't know that.
We got the constraint wrong on the 'r' field, using "r" tells the
compiler to put the value in a register. The value we then get in the
macro is the *register number*, not the value of the field.
That means when we mask the register number with 0x1 we get 0 or 1
depending on which register the compiler happens to put the constant
in, eg:
li r10,1
tlbiel r8,r9,2,0,0
li r7,1
tlbiel r10,r6,0,0,1
If we're unlucky we might generate an invalid instruction form, for
example RIC=0, PRS=1 and R=0, tlbiel r8,r7,0,1,0, this has been
observed to cause machine checks:
If the machine check happens early in boot while we have MSR_ME=0 it
will escalate into a checkstop and kill the box entirely.
To fix it we could change the inline asm constraint to "i" which
tells the compiler the value is a constant. But a better fix is to just
pass a literal 1 into the macro, which bypasses any problems with inline
asm constraints.
Fixes: d4748276ae14 ("powerpc/64s: Improve local TLB flush for boot and MCE on POWER9") Cc: stable@vger.kernel.org # v4.16+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Filipe Manana [Thu, 5 Apr 2018 21:55:12 +0000 (22:55 +0100)]
Btrfs: fix loss of prealloc extents past i_size after fsync log replay
Currently if we allocate extents beyond an inode's i_size (through the
fallocate system call) and then fsync the file, we log the extents but
after a power failure we replay them and then immediately drop them.
This behaviour happens since about 2009, commit c71bf099abdd ("Btrfs:
Avoid orphan inodes cleanup while replaying log"), because it marks
the inode as an orphan instead of dropping any extents beyond i_size
before replaying logged extents, so after the log replay, and while
the mount operation is still ongoing, we find the inode marked as an
orphan and then perform a truncation (drop extents beyond the inode's
i_size). Because the processing of orphan inodes is still done
right after replaying the log and before the mount operation finishes,
the intention of that commit does not make any sense (at least as
of today). However reverting that behaviour is not enough, because
we can not simply discard all extents beyond i_size and then replay
logged extents, because we risk dropping extents beyond i_size created
in past transactions, for example:
add prealloc extent beyond i_size
fsync - clears the flag BTRFS_INODE_NEEDS_FULL_SYNC from the inode
transaction commit
add another prealloc extent beyond i_size
fsync - triggers the fast fsync path
power failure
In that scenario, we would drop the first extent and then replay the
second one. To fix this just make sure that all prealloc extents
beyond i_size are logged, and if we find too many (which is far from
a common case), fallback to a full transaction commit (like we do when
logging regular extents in the fast fsync path).
# mount to replay log
$ mount /dev/sdb /mnt
# at this point the file only has one extent, at offset 0, size 256K
A test case for fstests follows soon, covering multiple scenarios that
involve adding prealloc extents with previous shrinking truncates and
without such truncates.
Fixes: c71bf099abdd ("Btrfs: Avoid orphan inodes cleanup while replaying log") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
Liu Bo [Fri, 30 Mar 2018 22:11:56 +0000 (06:11 +0800)]
Btrfs: clean up resources during umount after trans is aborted
Currently if some fatal errors occur, like all IO get -EIO, resources
would be cleaned up when
a) transaction is being committed or
b) BTRFS_FS_STATE_ERROR is set
However, in some rare cases, resources may be left alone after transaction
gets aborted and umount may run into some ASSERT(), e.g.
ASSERT(list_empty(&block_group->dirty_list));
For case a), in btrfs_commit_transaciton(), there're several places at the
beginning where we just call btrfs_end_transaction() without cleaning up
resources. For case b), it is possible that the trans handle doesn't have
any dirty stuff, then only trans hanlde is marked as aborted while
BTRFS_FS_STATE_ERROR is not set, so resources remain in memory.
This makes btrfs also check BTRFS_FS_STATE_TRANS_ABORTED to make sure that
all resources won't stay in memory after umount.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com> Signed-off-by: David Sterba <dsterba@suse.com>
Amir Goldstein [Thu, 29 Mar 2018 06:08:18 +0000 (09:08 +0300)]
ovl: add support for "xino" mount and config options
With mount option "xino=on", mounter declares that there are enough
free high bits in underlying fs to hold the layer fsid.
If overlayfs does encounter underlying inodes using the high xino
bits reserved for layer fsid, a warning will be emitted and the original
inode number will be used.
The mount option name "xino" goes after a similar meaning mount option
of aufs, but in overlayfs case, the mapping is stateless.
An example for a use case of "xino=on" is when upper/lower is on an xfs
filesystem. xfs uses 64bit inode numbers, but it currently never uses the
upper 8bit for inode numbers exposed via stat(2) and that is not likely to
change in the future without user opting-in for a new xfs feature. The
actual number of unused upper bit is much larger and determined by the xfs
filesystem geometry (64 - agno_log - agblklog - inopblog). That means
that for all practical purpose, there are enough unused bits in xfs
inode numbers for more than OVL_MAX_STACK unique fsid's.
Another use case of "xino=on" is when upper/lower is on tmpfs. tmpfs inode
numbers are allocated sequentially since boot, so they will practially
never use the high inode number bits.
For compatibility with applications that expect 32bit inodes, the feature
can be disabled with "xino=off". The option "xino=auto" automatically
detects underlying filesystem that use 32bit inodes and enables the
feature. The Kconfig option OVERLAY_FS_XINO_AUTO and module parameter of
the same name, determine if the default mode for overlayfs mount is
"xino=auto" or "xino=off".
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Mon, 6 Nov 2017 14:48:02 +0000 (16:48 +0200)]
ovl: consistent d_ino for non-samefs with xino
When overlay layers are not all on the same fs, but all inode numbers
of underlying fs do not use the high 'xino' bits, overlay st_ino values
are constant and persistent.
In that case, relax non-samefs constraint for consistent d_ino and always
iterate non-merge dir using ovl_fill_real() actor so we can remap lower
inode numbers to unique lower fs range.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Fri, 16 Mar 2018 08:39:37 +0000 (10:39 +0200)]
ovl: consistent i_ino for non-samefs with xino
When overlay layers are not all on the same fs, but all inode numbers
of underlying fs do not use the high 'xino' bits, overlay st_ino values
are constant and persistent.
In that case, set i_ino value to the same value as st_ino for nfsd
readdirplus validator.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Tue, 7 Nov 2017 11:55:04 +0000 (13:55 +0200)]
ovl: constant st_ino for non-samefs with xino
On 64bit systems, when overlay layers are not all on the same fs, but
all inode numbers of underlying fs are not using the high bits, use the
high bits to partition the overlay st_ino address space. The high bits
hold the fsid (upper fsid is 0). This way overlay inode numbers are unique
and all inodes use overlay st_dev. Inode numbers are also persistent
for a given layer configuration.
Currently, our only indication for available high ino bits is from a
filesystem that supports file handles and uses the default encode_fh()
operation, which encodes a 32bit inode number.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Vivek Goyal [Fri, 9 Mar 2018 20:44:43 +0000 (15:44 -0500)]
ovl: set d->is_dir and d->opaque for last path element
Certain properties in ovl_lookup_data should be set only for the last
element of the path. IOW, if we are calling ovl_lookup_single() for an
absolute redirect, then d->is_dir and d->opaque do not make much sense
for intermediate path elements. Instead set them only if dentry being
lookup is last path element.
As of now we do not seem to be making use of d->opaque if it is set for
a path/dentry in lower. But just define the semantics so that future code
can make use of this assumption.
Vivek Goyal [Fri, 9 Mar 2018 20:44:42 +0000 (15:44 -0500)]
ovl: Do not check for redirect if this is last layer
If we are looking in last layer, then there should not be any need to
process redirect. redirect information is used only for lookup in next
lower layer and there is no more lower layer to look into. So no need
to process redirects.
Amir Goldstein [Fri, 9 Mar 2018 15:05:55 +0000 (17:05 +0200)]
ovl: lookup in inode cache first when decoding lower file handle
When decoding a lower file handle, we need to check if lower file was
copied up and indexed and if it has a whiteout index, we need to check
if this is an unlinked but open non-dir before returning -ESTALE.
To find out if this is an unlinked but open non-dir we need to lookup
an overlay inode in inode cache by lower inode and that requires decoding
the lower file handle before looking in inode cache.
Before this change, if the lower inode turned out to be a directory, we
may have paid an expensive cost to reconnect that lower directory for
nothing.
After this change, we start by decoding a disconnected lower dentry and
using the lower inode for looking up an overlay inode in inode cache.
If we find overlay inode and dentry in cache, we avoid the index lookup
overhead. If we don't find an overlay inode and dentry in cache, then we
only need to decode a connected lower dentry in case the lower dentry is
a non-indexed directory.
The xfstests group overlay/exportfs tests decoding overlayfs file
handles after drop_caches with different states of the file at encode
and decode time. Overall the tests in the group call ovl_lower_fh_to_d()
89 times to decode a lower file handle.
Before this change, the tests called ovl_get_index_fh() 75 times and
reconnect_one() 61 times.
After this change, the tests call ovl_get_index_fh() 70 times and
reconnect_one() 59 times. The 2 cases where reconnect_one() was avoided
are cases where a non-upper directory file handle was encoded, then the
directory removed and then file handle was decoded.
To demonstrate the affect on decoding file handles with hot inode/dentry
cache, the drop_caches call in the tests was disabled. Without
drop_caches, there are no reconnect_one() calls at all before or after
the change. Before the change, there are 75 calls to ovl_get_index_fh(),
exactly as the case with drop_caches. After the change, there are only
10 calls to ovl_get_index_fh().
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Fri, 9 Mar 2018 13:51:02 +0000 (15:51 +0200)]
ovl: do not try to reconnect a disconnected origin dentry
On lookup of non directory, we try to decode the origin file handle
stored in upper inode. The origin file handle is supposed to be decoded
to a disconnected non-dir dentry, which is fine, because we only need
the lower inode of a copy up origin.
However, if the origin file handle somehow turns out to be a directory
we pay the expensive cost of reconnecting the directory dentry, only to
get a mismatch file type and drop the dentry.
Optimize this case by explicitly opting out of reconnecting the dentry.
Opting-out of reconnect is done by passing a NULL acceptable callback
to exportfs_decode_fh().
While the case described above is a strange corner case that does not
really need to be optimized, the API added for this optimization will
be used by a following patch to optimize a more common case of decoding
an overlayfs file handle.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Fri, 2 Feb 2018 08:42:03 +0000 (10:42 +0200)]
ovl: disambiguate ovl_encode_fh()
Rename ovl_encode_fh() to ovl_encode_real_fh() to differentiate from the
exportfs function ovl_encode_inode_fh() and change the latter to
ovl_encode_fh() to match the exportfs method name.
Rename ovl_decode_fh() to ovl_decode_real_fh() for consistency.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Amir Goldstein [Mon, 12 Mar 2018 14:30:41 +0000 (10:30 -0400)]
ovl: fix lookup with middle layer opaque dir and absolute path redirects
As of now if we encounter an opaque dir while looking for a dentry, we set
d->last=true. This means that there is no need to look further in any of
the lower layers. This works fine as long as there are no redirets or
relative redircts. But what if there is an absolute redirect on the
children dentry of opaque directory. We still need to continue to look into
next lower layer. This patch fixes it.
Here is an example to demonstrate the issue. Say you have following setup.
upper: /redirect (redirect=/a/b/c)
lower1: /a/[b]/c ([b] is opaque) (c has absolute redirect=/a/b/d/)
lower0: /a/b/d/foo
Now "redirect" dir should merge with lower1:/a/b/c/ and lower0:/a/b/d.
Note, despite the fact lower1:/a/[b] is opaque, we need to continue to look
into lower0 because children c has an absolute redirect.
Vivek Goyal [Fri, 9 Mar 2018 20:44:41 +0000 (15:44 -0500)]
ovl: Set d->last properly during lookup
d->last signifies that this is the last layer we are looking into and there
is no more. And that means this allows for some optimzation opportunities
during lookup. For example, in ovl_lookup_single() we don't have to check
for opaque xattr of a directory is this is the last layer we are looking
into (d->last = true).
But knowing for sure whether we are looking into last layer can be very
tricky. If redirects are not enabled, then we can look at poe->numlower and
figure out if the lookup we are about to is last layer or not. But if
redircts are enabled then it is possible poe->numlower suggests that we are
looking in last layer, but there is an absolute redirect present in found
element and that redirects us to a layer in root and that means lookup will
continue in lower layers further.
In this case pure is "pure upper". When we look for "foo", that time
poe->numlower=0. But that alone does not mean that we will not search for a
merge candidate in /lowerdir. Absolute redirect changes that.
IOW, d->last should not be set just based on poe->numlower if redirects are
enabled. That can lead to setting d->last while it should not have and that
means we will not check for opaque xattr while we should have.
So do this.
- If redirects are not enabled, then continue to rely on poe->numlower
information to determine if it is last layer or not.
- If redirects are enabled, then set d->last = true only if this is the
last layer in root ovl_entry (roe).
Amir Goldstein [Thu, 15 Mar 2018 21:39:01 +0000 (23:39 +0200)]
ovl: set i_ino to the value of st_ino for NFS export
Eddie Horng reported that readdir of an overlayfs directory that
was exported via NFSv3 returns entries with d_type set to DT_UNKNOWN.
The reason is that while preparing the response for readdirplus, nfsd
checks inside encode_entryplus_baggage() that a child dentry's inode
number matches the value of d_ino returns by overlayfs readdir iterator.
Because the overlayfs inodes use arbitrary inode numbers that are not
correlated with the values of st_ino/d_ino, NFSv3 falls back to not
encoding d_type. Although this is an allowed behavior, we can fix it for
the case of all overlayfs layers on the same underlying filesystem.
When NFS export is enabled and d_ino is consistent with st_ino
(samefs), set the same value also to i_ino in ovl_fill_inode() for all
overlayfs inodes, nfsd readdirplus sanity checks will pass.
ovl_fill_inode() may be called from ovl_new_inode(), before real inode
was created with ino arg 0. In that case, i_ino will be updated to real
upper inode i_ino on ovl_inode_init() or ovl_inode_update().
Reported-by: Eddie Horng <eddiehorng.tw@gmail.com> Tested-by: Eddie Horng <eddiehorng.tw@gmail.com> Signed-off-by: Amir Goldstein <amir73il@gmail.com> Fixes: 8383f1748829 ("ovl: wire up NFS export operations") Cc: <stable@vger.kernel.org> #v4.16 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Song Liu [Wed, 11 Apr 2018 18:02:37 +0000 (18:02 +0000)]
perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open()
Non-root user cannot create kprobe or uprobe through the text-based
interface (kprobe_events, uprobe_events),so they should not be able
to create probes via perf_event_open() either.
Reported-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Song Liu <songliubraving@fb.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 33ea4b24277b ("perf/core: Implement the 'perf_uprobe' PMU") Fixes: e12f03d7031a ("perf/core: Implement the 'perf_kprobe' PMU") Link: http://lkml.kernel.org/r/C0B2EFB5-C403-4BDB-9046-C14B3EE66999@fb.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
x86/pgtable: Don't set huge PUD/PMD on non-leaf entries
The pmd_set_huge() and pud_set_huge() functions are used from
the generic ioremap() code to establish large mappings where this
is possible.
But the generic ioremap() code does not check whether the
PMD/PUD entries are already populated with a non-leaf entry,
so that any page-table pages these entries point to will be
lost.
Further, on x86-32 with SHARED_KERNEL_PMD=0, this causes a
BUG_ON() in vmalloc_sync_one() when PMD entries are synced
from swapper_pg_dir to the current page-table. This happens
because the PMD entry from swapper_pg_dir was promoted to a
huge-page entry while the current PGD still contains the
non-leaf entry. Because both entries are present and point
to a different page, the BUG_ON() triggers.
This was actually triggered with pti-x32 enabled in a KVM
virtual machine by the graphics driver.
A real and better fix for that would be to improve the
page-table handling in the generic ioremap() code. But that is
out-of-scope for this patch-set and left for later work.
Reported-by: David H. Gutteridge <dhgutteridge@sympatico.ca> Signed-off-by: Joerg Roedel <jroedel@suse.de> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: David Laight <David.Laight@aculab.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Eduardo Valentin <eduval@amazon.com> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Waiman Long <llong@redhat.com> Cc: Will Deacon <will.deacon@arm.com> Cc: aliguori@amazon.com Cc: daniel.gruss@iaik.tugraz.at Cc: hughd@google.com Cc: keescook@google.com Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180411152437.GC15462@8bytes.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Fri, 6 Apr 2018 20:55:18 +0000 (13:55 -0700)]
x86/pti: Leave kernel text global for !PCID
Global pages are bad for hardening because they potentially let an
exploit read the kernel image via a Meltdown-style attack which
makes it easier to find gadgets.
But, global pages are good for performance because they reduce TLB
misses when making user/kernel transitions, especially when PCIDs
are not available, such as on older hardware, or where a hypervisor
has disabled them for some reason.
This patch implements a basic, sane policy: If you have PCIDs, you
only map a minimal amount of kernel text global. If you do not have
PCIDs, you map all kernel text global.
This policy effectively makes PCIDs something that not only adds
performance but a little bit of hardening as well.
I ran a simple "lseek" microbenchmark[1] to test the benefit on
a modern Atom microserver. Most of the benefit comes from applying
the series before this patch ("entry only"), but there is still a
signifiant benefit from this patch.
No Global Lines (baseline ): 6077741 lseeks/sec
88 Global Lines (entry only): 7528609 lseeks/sec (+23.9%)
94 Global Lines (this patch): 8433111 lseeks/sec (+38.8%)
Dave Hansen [Fri, 6 Apr 2018 20:55:17 +0000 (13:55 -0700)]
x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image
Summary:
In current kernels, with PTI enabled, no pages are marked Global. This
potentially increases TLB misses. But, the mechanism by which the Global
bit is set and cleared is rather haphazard. This patch makes the process
more explicit. In the end, it leaves us with Global entries in the page
tables for the areas truly shared by userspace and kernel and increases
TLB hit rates.
The place this patch really shines in on systems without PCIDs. In this
case, we are using an lseek microbenchmark[1] to see how a reasonably
non-trivial syscall behaves. Higher is better:
No Global pages (baseline): 6077741 lseeks/sec
88 Global Pages (this set): 7528609 lseeks/sec (+23.9%)
On a modern Skylake desktop with PCIDs, the benefits are tangible, but not
huge for a kernel compile (lower is better):
No Global pages (baseline): 186.951 seconds time elapsed ( +- 0.35% )
28 Global pages (this set): 185.756 seconds time elapsed ( +- 0.09% )
-1.195 seconds (-0.64%)
I also re-checked everything using the lseek1 test[1]:
No Global pages (baseline): 15783951 lseeks/sec
28 Global pages (this set): 16054688 lseeks/sec
+270737 lseeks/sec (+1.71%)
The effect is more visible, but still modest.
Details:
The kernel page tables are inherited from head_64.S which rudely marks
them as _PAGE_GLOBAL. For PTI, we have been relying on the grace of
$DEITY and some insane behavior in pageattr.c to clear _PAGE_GLOBAL.
This patch tries to do better.
First, stop filtering out "unsupported" bits from being cleared in the
pageattr code. It's fine to filter out *setting* these bits but it
is insane to keep us from clearing them.
Then, *explicitly* go clear _PAGE_GLOBAL from the kernel identity map.
Do not rely on pageattr to do it magically.
After this patch, we can see that "GLB" shows up in each copy of the
page tables, that we have the same number of global entries in each
and that they are the *same* entries.
A quick visual audit also shows that all the entries make sense.
0xfffffe0000000000 is the cpu_entry_area and 0xffffffff81c00000
is the entry/exit text:
Dave Hansen [Fri, 6 Apr 2018 20:55:14 +0000 (13:55 -0700)]
x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init
__ro_after_init data gets stuck in the .rodata section. That's normally
fine because the kernel itself manages the R/W properties.
But, if we run __change_page_attr() on an area which is __ro_after_init,
the .rodata checks will trigger and force the area to be immediately
read-only, even if it is early-ish in boot. This caused problems when
trying to clear the _PAGE_GLOBAL bit for these area in the PTI code:
it cleared _PAGE_GLOBAL like I asked, but also took it up on itself
to clear _PAGE_RW. The kernel then oopses the next time it wrote to
a __ro_after_init data structure.
To fix this, add the kernel_set_to_readonly check, just like we have
for kernel text, just a few lines below in this function.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180406205514.8D898241@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Fri, 6 Apr 2018 20:55:13 +0000 (13:55 -0700)]
x86/mm: Comment _PAGE_GLOBAL mystery
I was mystified as to where the _PAGE_GLOBAL in the kernel page tables
for kernel text came from. I audited all the places I could find, but
I missed one: head_64.S.
The page tables that we create in here live for a long time, and they
also have _PAGE_GLOBAL set, despite whether the processor supports it
or not. It's harmless, and we got *lucky* that the pageattr code
accidentally clears it when we wipe it out of __supported_pte_mask and
then later try to mark kernel text read-only.
Comment some of these properties to make it easier to find and
understand in the future.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180406205513.079BB265@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Fri, 6 Apr 2018 20:55:11 +0000 (13:55 -0700)]
x86/mm: Remove extra filtering in pageattr code
The pageattr code has a mode where it can set or clear PTE bits in
existing PTEs, so the page protections of the *new* PTEs come from
one of two places:
1. The set/clear masks: cpa->mask_clr / cpa->mask_set
2. The existing PTE
We filter ->mask_set/clr for supported PTE bits at entry to
__change_page_attr() so we never need to filter them again.
The only other place permissions can come from is an existing PTE
and those already presumably have good bits. We do not need to filter
them again.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180406205511.BC072352@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Hansen [Fri, 6 Apr 2018 20:55:09 +0000 (13:55 -0700)]
x86/mm: Do not auto-massage page protections
A PTE is constructed from a physical address and a pgprotval_t.
__PAGE_KERNEL, for instance, is a pgprot_t and must be converted
into a pgprotval_t before it can be used to create a PTE. This is
done implicitly within functions like pfn_pte() by massage_pgprot().
However, this makes it very challenging to set bits (and keep them
set) if your bit is being filtered out by massage_pgprot().
This moves the bit filtering out of pfn_pte() and friends. For
users of PAGE_KERNEL*, filtering will be done automatically inside
those macros but for users of __PAGE_KERNEL*, they need to do their
own filtering now.
Note that we also just move pfn_pte/pmd/pud() over to check_pgprot()
instead of massage_pgprot(). This way, we still *look* for
unsupported bits and properly warn about them if we find them. This
might happen if an unfiltered __PAGE_KERNEL* value was passed in,
for instance.
- printk format warning fix from: Arnd Bergmann <arnd@arndb.de>
- boot crash fix from: Tom Lendacky <thomas.lendacky@amd.com>
- crash bisected by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reported-and-fixed-by: Arnd Bergmann <arnd@arndb.de> Fixed-by: Tom Lendacky <thomas.lendacky@amd.com> Bisected-by: Mike Galbraith <efault@gmx.de> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Hugh Dickins <hughd@google.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Kees Cook <keescook@google.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nadav Amit <namit@vmware.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mm@kvack.org Link: http://lkml.kernel.org/r/20180406205509.77E1D7F6@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org>
Merge tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- OF_IOMMU support for the Rockchip iommu driver so that it can use
generic DT bindings
- rework of locking in the AMD IOMMU interrupt remapping code to make
it work better in RT kernels
- support for improved iotlb flushing in the AMD IOMMU driver
- support for 52-bit physical and virtual addressing in the ARM-SMMU
- various other small fixes and cleanups
* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
iommu/rockchip: Support sharing IOMMU between masters
iommu/rockchip: Add runtime PM support
iommu/rockchip: Fix error handling in init
iommu/rockchip: Use OF_IOMMU to attach devices automatically
iommu/rockchip: Use IOMMU device for dma mapping operations
dt-bindings: iommu/rockchip: Add clock property
iommu/rockchip: Control clocks needed to access the IOMMU
iommu/rockchip: Fix TLB flush of secondary IOMMUs
iommu/rockchip: Use iopoll helpers to wait for hardware
iommu/rockchip: Fix error handling in attach
iommu/rockchip: Request irqs in rk_iommu_probe()
iommu/rockchip: Fix error handling in probe
iommu/rockchip: Prohibit unbind and remove
iommu/amd: Return proper error code in irq_remapping_alloc()
iommu/amd: Make amd_iommu_devtable_lock a spin_lock
iommu/amd: Drop the lock while allocating new irq remap table
iommu/amd: Factor out setting the remap table for a devid
iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
iommu/amd: Remove the special case from alloc_irq_table()
...
Merge tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These include one big-ticket item which is the rework of the idle loop
in order to prevent CPUs from spending too much time in shallow idle
states. It reduces idle power on some systems by 10% or more and may
improve performance of workloads in which the idle loop overhead
matters. This has been in the works for several weeks and it has been
tested and reviewed quite thoroughly.
Also included are changes that finalize the cpufreq cleanup moving
frequency table validation from drivers to the core, a few fixes and
cleanups of cpufreq drivers, a cpuidle documentation update and a PM
QoS core update to mark the expected switch fall-throughs in it.
Specifics:
- Rework the idle loop in order to prevent CPUs from spending too
much time in shallow idle states by making it stop the scheduler
tick before putting the CPU into an idle state only if the idle
duration predicted by the idle governor is long enough.
That required the code to be reordered to invoke the idle governor
before stopping the tick, among other things (Rafael Wysocki,
Frederic Weisbecker, Arnd Bergmann).
- Add the missing description of the residency sysfs attribute to the
cpuidle documentation (Prashanth Prakash).
- Finalize the cpufreq cleanup moving frequency table validation from
drivers to the core (Viresh Kumar).
- Fix a clock leak regression in the armada-37xx cpufreq driver
(Gregory Clement).
- Fix the initialization of the CPU performance data structures for
shared policies in the CPPC cpufreq driver (Shunyong Yang).
- Clean up the ti-cpufreq, intel_pstate and CPPC cpufreq drivers a
bit (Viresh Kumar, Rafael Wysocki).
- Mark the expected switch fall-throughs in the PM QoS core (Gustavo
Silva)"
* tag 'pm-4.17-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
tick-sched: avoid a maybe-uninitialized warning
cpufreq: Drop cpufreq_table_validate_and_show()
cpufreq: SCMI: Don't validate the frequency table twice
cpufreq: CPPC: Initialize shared perf capabilities of CPUs
cpufreq: armada-37xx: Fix clock leak
cpufreq: CPPC: Don't set transition_latency
cpufreq: ti-cpufreq: Use builtin_platform_driver()
cpufreq: intel_pstate: Do not include debugfs.h
PM / QoS: mark expected switch fall-throughs
cpuidle: Add definition of residency to sysfs documentation
time: hrtimer: Use timerqueue_iterate_next() to get to the next timer
nohz: Avoid duplication of code related to got_idle_tick
nohz: Gather tick_sched booleans under a common flag field
cpuidle: menu: Avoid selecting shallow states with stopped tick
cpuidle: menu: Refine idle state selection for running tick
sched: idle: Select idle state before stopping the tick
time: hrtimer: Introduce hrtimer_next_event_without()
time: tick-sched: Split tick_nohz_stop_sched_tick()
cpuidle: Return nohz hint from cpuidle_select()
jiffies: Introduce USER_TICK_USEC and redefine TICK_USEC
...
Merge tag 'ktest-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest updates from Steven Rostedt:
"These commits have either been sitting in my INBOX or have been in my
local tree for some time. I need to push them upstream:
- Separate out config-bisect.pl from ktest.pl.
This allows users to do config bisects without full ktest setup.
- Email on status change.
Allow the user to be emailed on test start, finish, failure, etc.
- Other small fixes and enhancements"
* tag 'ktest-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest: (24 commits)
ktest: Take submenu into account for grub2 menus
ktest.pl: Add MAIL_COMMAND option to define how to send email
ktest.pl: Use run_command to execute sending mail
ktest.pl: Allow dodie be recursive
ktest.pl: Kill test if mailer is not supported
ktest.pl: Add MAIL_PATH option to define where to find the mailer
ktest.pl: No need to print no mailer is specified when mailto is not
Ktest: add email options to sample.config
Ktest: Use dodie for critical falures
Ktest: Add SigInt handling
Ktest: Add email support
ktest.pl: Detect if a config-bisect was interrupted
ktest.pl: Make finding config-bisect.pl dynamic
ktest.pl: Have ktest.pl pass -r to config-bisect.pl to reset bisect
ktest.pl: Use diffconfig if available for failed config bisects
ktest.pl: Allow for the config-bisect.pl output to display to console
ktest: Use config-bisect.pl in ktest.pl
ktest: Add standalone config-bisect.pl program
ktest: Set do_not_reboot=y for CONFIG_BISECT_TYPE=build
ktest: Set buildonly=1 for CONFIG_BISECT_TYPE=build
...
- a new and faster epoll based IRQ controller and NIC driver
- misc fixes and janitorial updates
* git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
Fix vector raw inintialization logic
Migrate vector timers to new timer API
um: Compile with modern headers
um: vector: Fix an error handling path in 'vector_parse()'
um: vector: Fix a memory allocation check
um: vector: fix missing unlock on error in vector_net_open()
um: Add missing EXPORT for free_irq_by_fd()
High Performance UML Vector Network Driver
Epoll based IRQ controller
um: Use POSIX ucontext_t instead of struct ucontext
um: time: Use timespec64 for persistent clock
um: Restore symbol versions for __memcpy and memcpy
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Here is a very small set of fixes for inclusion in linux-4.17-rc1: Two
changes for the maintainer file, and one more fix for the newly added
npcm platform, to enable the level 2 cache controller"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Update ASPEED entry with details
MAINTAINERS: Migrate oxnas list to groups.io
arm: npcm: enable L2 cache in NPCM7xx architecture
Merge tag 'nios2-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2
Pull nios2 update from Ley Foon Tan:
"Use read_persistent_clock64() instead of read_persistent_clock()"
* tag 'nios2-v4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
nios2: Use read_persistent_clock64() instead of read_persistent_clock()
* Since cifs_vfs_error was just using pr_debug_ratelimited like the rest
of cifs_dbg, move it there too
* Add a ONCE type flag to call the pr_xxx_once() debug function instead
of the ratelimited ones.
To convert existing printk_once() calls to this we can run:
fs/cifs/inode.c: In function ‘simple_hashstr’:
fs/cifs/inode.c:713: warning: integer constant is too large for ‘long’ type
Fixes: 7ea884c77e5c97f1 ("smb3: Fix root directory when server returns inode number of zero") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Steve French [Wed, 4 Apr 2018 19:08:52 +0000 (14:08 -0500)]
SMB3: Log at least once if tree connect fails during reconnect
Adding an extra debug message to show if a tree connect failure during
reconnect (and made it a log once so it doesn't spam the logs).
Saw a case recently where tree connect repeatedly returned
access denied on reconnect and it wasn't as easy to spot as it
should have been.
Signed-off-by: Steve French <smfrench@gmail.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com>
tcon->ses is being dereferenced before it is null checked, hence
there is a potential null pointer dereference.
Fix this by moving the pointer dereference after tcon->ses has
been properly null checked.
Addresses-Coverity-ID: 1467426 ("Dereference before null check") Fixes: 93012bf98416 ("cifs: add server->vals->header_preamble_size") Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com>
David S. Miller [Wed, 11 Apr 2018 21:41:28 +0000 (17:41 -0400)]
Merge branch 'l2tp-tunnel-creation-fixes'
Guillaume Nault says:
====================
l2tp: tunnel creation fixes
L2TP tunnel creation is racy. We need to make sure that the tunnel
returned by l2tp_tunnel_create() isn't going to be freed while the
caller is using it. This is done in patch #1, by separating tunnel
creation from tunnel registration.
With the tunnel registration code in place, we can now check for
duplicate tunnels in a race-free way. This is done in patch #2, which
incidentally removes the last use of l2tp_tunnel_find().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux.git / log