clocksource/drivers/rda: Add clock driver for RDA8810PL SoC
Add clock driver for RDA Micro RDA8810PL SoC supporting OSTIMER
and HWTIMER.
RDA8810PL has two independent timers: OSTIMER (56 bit) and HWTIMER
(64 bit). Each timer provides optional interrupt support. In this
driver, OSTIMER is used for clockevents and HWTIMER is used for
clocksource.
Signed-off-by: Andreas Färber <afaerber@suse.de> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Anup Patel [Tue, 4 Dec 2018 10:29:52 +0000 (15:59 +0530)]
clocksource/drivers/riscv_timer: Provide the sched_clock
Currently, we don't have a sched_clock registered for RISC-V systems.
This means Linux time keeping will use jiffies (running at HZ) as the
default sched_clock.
To avoid this, we explicity provide sched_clock using RISC-V rdtime
instruction (similar to riscv_timer clocksource).
Anson Huang [Fri, 7 Dec 2018 06:05:36 +0000 (06:05 +0000)]
clocksource/drivers/timer-imx-tpm: Specify clock name for timer-of
i.MX TPM needs "ipg" clock for register access and "per" clock for
timer function, the driver gets "ipg" clock by searching the clock
name, but timer-of initialization will get first clock in device
tree TPM node since no clock name specified in of_clk, that means
the "per" clock MUST be the first clock entry in device tree TPM
node, this patch specifies clock name for of_clk to avoid this
restriction, it makes TPM driver work properly with different sequence
of clock entries in device tree TPM node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
TIMER_INTR_MASK register (Base Address of Timer + 0x38) is not designed
for masking interrupts on ast2500 chips, and it's not even listed in
ast2400 datasheet, so it's not safe to access TIMER_INTR_MASK on aspeed
chips.
Similarly, TIMER_INTR_STATE register (Base Address of Timer + 0x34) is
not interrupt status register on ast2400 and ast2500 chips. Although
there is no side effect to reset the register in fttmr010_common_init(),
it's just misleading to do so.
Besides, "count_down" is renamed to "is_aspeed" in "fttmr010" structure,
and more comments are added so the code is more readble.
Signed-off-by: Tao Ren <taoren@fb.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The function of_find_node_by_path() acquires a reference to the node
returned by it and that reference needs to be dropped by its caller.
integrator_ap_timer_init_of() doesn't do that. The pri_node and the
sec_node are used as an identifier to compare against the current
node, so we can directly drop the refcount after getting the node from
the path as it is not used as pointer.
By dropping the refcount right after getting it, a single variable is
needed instead of two.
Fix this by use a single variable and drop the refcount right after
of_find_node_by_path().
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Stefan Wahren [Sat, 10 Nov 2018 15:28:39 +0000 (16:28 +0100)]
clocksource/drivers/bcm2835: Switch to SPDX identifier
Adopt the SPDX license identifier headers to ease license compliance
management. Also drop the FSF address.
Cc: Simon Arlott <simon@arlott.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Biju Das [Mon, 19 Nov 2018 16:14:13 +0000 (16:14 +0000)]
dt-bindings: timer: renesas, cmt: Document r8a774a1 CMT support
Document SoC specific bindings for RZ/G2M (r8a774a1) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Anson Huang [Tue, 6 Nov 2018 05:15:58 +0000 (05:15 +0000)]
clocksource/drivers/timer-imx-tpm: Convert the driver to timer-of
Convert the driver to use the timer_of helpers. This allows to handle
timer base, clock and irq using common timer_of driver and it
simplifies the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It turned out we used to use default implementation of sched_clock()
from kernel/sched/clock.c which was as precise as 1/HZ, i.e.
by default we had 10 msec granularity of time measurement.
Now given ARC built-in timers are clocked with the same frequency as
CPU cores we may get much higher precision of time tracking.
Thus we switch to generic sched_clock which really reads ARC hardware
counters.
This is especially helpful for measuring short events.
That's what we used to have:
------------------------------>8------------------------
$ perf stat /bin/sh -c /root/lmbench-master/bin/arc/hello > /dev/null
Performance counter stats for '/bin/sh -c /root/lmbench-master/bin/arc/hello':
Biju Das [Fri, 26 Oct 2018 08:36:13 +0000 (09:36 +0100)]
dt-bindings: timer: renesas, cmt: Document r8a77470 CMT support
Document SoC specific compatible strings for r8a77470. No driver change
is needed as the fallback strings will activate the right code.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Biju Das [Fri, 26 Oct 2018 08:01:44 +0000 (09:01 +0100)]
dt-bindings: timer: renesas, cmt: Document r8a7796 CMT support
Document SoC specific bindings for R-Car M3-W (r8a7796) SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com> Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
clocksource/drivers/meson6_timer: Implement the ARM delay timer
Implement an ARM delay timer to be used for udelay(). This allows us to
skip the delay loop calibration at boot.
With this patch udelay() is now independent of CPU frequency changes.
This is a good thing on Meson8, Meson8b and Meson8m2 because changing
the CPU frequency requires running the CPU clock off the XTAL while
changing the PLL or it's dividers. After changing the CPU clocks we need
to wait a few usecs for the clock to become stable. So having an
udelay() implementation that doesn't depend on the CPU frequency is
beneficial.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
clocksource/drivers/meson6_timer: Use register names from the datasheet
This makes the driver use the names from S805 datasheet for the
preprocessor #defines. This makes it easier to spot that the driver
currently only supports Timer A (as clockevent with interrupt support)
and Timer E (as clocksource without interrupts). Timer B, C and D (which
are similar to Timer A) are currently not supported by the driver.
While here, this also removes the internal "CED_ID" and "CSD_ID" defines
which are used to identify the timer. These IDs are not described in the
datasheet and thus make it harder to compare the code to what's written
in the datasheet.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Linus Walleij [Thu, 15 Nov 2018 13:32:03 +0000 (14:32 +0100)]
clocksource/drivers/ux500: Drop Ux500 custom SCHED_CLOCK
The two drivers used for Ux500 sched_clock use two Kconfig
symbols to select which of the two gets used as sched_clock.
This isn't right: the workaround is trying to make sure that
the NONSTOP timer is used for sched_clock in order to keep
that clock ticking consistently over a suspend/resume
cycle. (Otherwise sched_clock simply stops during suspend
and continues after resume).
This will notably affect any timetstamped debug prints,
so that they show the absolute number of seconds since the
system was booted and does not loose wall-clock time during
suspend and resume as if time stood still.
The real way to fix this problem is to make sched_clock
take advantage of any NONSTOP clock source on the system
and adjust accordingly, not to try to work around this by
using a different sched_clock depending on what system
we are compiling for. This can solve the problem for
everyone instead of providing a local solution.
Cc: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Demote the DBx500 PRCMU clocksource to quality 100 and
mark it as NONSTOP so it will still be used for
timekeeping across suspend/resume.
The Nomadik MTU timer which has higher precision will
be used when the system is up and running, thanks to
the recent changes properly utilizing the suspend
clocksources.
This was discussed back in 2011 when the driver was
written, but the infrastructure was not available
upstream to use this timer properly. Now the
infrastructure is there, so let's finalize the work.
Cc: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Baolin Wang <baolin.wang@linaro.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Bart Van Assche [Wed, 28 Nov 2018 23:43:09 +0000 (15:43 -0800)]
timekeeping: Use proper seqcount initializer
tk_core.seq is initialized open coded, but that misses to initialize the
lockdep map when lockdep is enabled. Lockdep splats involving tk_core seq
consequently lack a name and are hard to read.
Use the proper initializer which takes care of the lockdep map
initialization.
Thomas Gleixner [Wed, 31 Oct 2018 18:21:16 +0000 (19:21 +0100)]
posix-timers: Remove license boilerplate
The SPDX identifier defines the license of the file already. No need for
the boilerplate.
Remove also the completely outdated Montavista snail mail address.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182253.479792883@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:15 +0000 (19:21 +0100)]
posix-clocks: Remove license boiler plate
The SPDX identifier defines the license of the file already. No need for
the boilerplate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Richard Cochran <richardcochran@gmail.com> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182253.385909804@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:14 +0000 (19:21 +0100)]
sched/clock: Remove license boilerplate
The SPDX identifier defines the license of the file already. No need for
the boilerplate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182253.300140921@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:13 +0000 (19:21 +0100)]
posix-timers/stubs: Remove license boilerplate
The SPDX identifier defines the license of the file already. No need for
the boilerplate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Link: https://lkml.kernel.org/r/20181031182253.215825217@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:12 +0000 (19:21 +0100)]
time: Remove license boilerplate
The SPDX identifier defines the license of the files already. No need for
the boilerplates.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Acked-by: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Link: https://lkml.kernel.org/r/20181031182253.132458951@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:11 +0000 (19:21 +0100)]
time/debug: Remove license boilerplate
The SPDX identifier is enough. Remove the license boilerplate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182253.047449481@linutronix.de
"For licencing details see kernel-base/COPYING" and similar license
references have no value over the SPDX identifier. Remove them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182252.963632760@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:09 +0000 (19:21 +0100)]
time: Add SPDX license identifiers
Update the time(r) core files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of the
full boiler plate text.
This work is based on a script and data from Philippe Ombredanne, Kate
Stewart and myself. The data has been created with two independent license
scanners and manual inspection.
The following files do not contain any direct license information and have
been omitted from the big initial SPDX changes:
timeconst.bc: The .bc files were not touched
time.c, timer.c, timekeeping.c: Licence was deduced from EXPORT_SYMBOL_GPL
As those files do not contain direct license references they fall under the
project license, i.e. GPL V2 only.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Nicolas Pitre <nicolas.pitre@linaro.org> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Link: https://lkml.kernel.org/r/20181031182252.879109557@linutronix.de
Thomas Gleixner [Wed, 31 Oct 2018 18:21:08 +0000 (19:21 +0100)]
time: Remove useless filenames in top level comments
Remove the pointless filenames in the top level comments. They have no
value at all and just occupy space. While at it tidy up some of the
comments and remove a stale one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Nicolas Pitre <nico@linaro.org> Acked-by: Kees Cook <keescook@chromium.org> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: John Stultz <john.stultz@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Peter Anvin <hpa@zytor.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Richard Cochran <richardcochran@gmail.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Cc: David Riley <davidriley@chromium.org> Cc: Colin Cross <ccross@android.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lkml.kernel.org/r/20181031182252.794898238@linutronix.de
Linus Torvalds [Sun, 4 Nov 2018 22:46:04 +0000 (14:46 -0800)]
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Linus Torvalds [Sun, 4 Nov 2018 16:20:09 +0000 (08:20 -0800)]
Merge tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Bugfix:
- Fix build issues on architectures that don't provide 64-bit cmpxchg
Cleanups:
- Fix a spelling mistake"
* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: fix spelling mistake, EACCESS -> EACCES
SUNRPC: Use atomic(64)_t for seq_send(64)
Linus Torvalds [Sun, 4 Nov 2018 16:12:44 +0000 (08:12 -0800)]
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
Linus Torvalds [Sun, 4 Nov 2018 01:37:09 +0000 (18:37 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Linus Torvalds [Sun, 4 Nov 2018 01:25:17 +0000 (18:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Linus Torvalds [Sun, 4 Nov 2018 01:13:43 +0000 (18:13 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Linus Torvalds [Sun, 4 Nov 2018 01:12:09 +0000 (18:12 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
Linus Torvalds [Sat, 3 Nov 2018 17:55:23 +0000 (10:55 -0700)]
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kprobe: make page to RO mode when allocate it
arm64: kdump: fix small typo
arm64: makefile fix build of .i file in external module case
Linus Torvalds [Sat, 3 Nov 2018 17:45:55 +0000 (10:45 -0700)]
Merge tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes and updates from Steve French:
"Three small fixes (one Kerberos related, one for stable, and another
fixes an oops in xfstest 377), two helpful debugging improvements,
three patches for cifs directio and some minor cleanup"
* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix signed/unsigned mismatch on aio_read patch
cifs: don't dereference smb_file_target before null check
CIFS: Add direct I/O functions to file_operations
CIFS: Add support for direct I/O write
CIFS: Add support for direct I/O read
smb3: missing defines and structs for reparse point handling
smb3: allow more detailed protocol info on open files for debugging
smb3: on kerberos mount if server doesn't specify auth type use krb5
smb3: add trace point for tree connection
cifs: fix spelling mistake, EACCESS -> EACCES
cifs: fix return value for cifs_listxattr
Linus Torvalds [Sat, 3 Nov 2018 17:35:52 +0000 (10:35 -0700)]
Merge branch 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull 9p fix from Al Viro:
"Regression fix for net/9p handling of iov_iter; broken by braino when
switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: Fix 9p virtio breakage
Linus Torvalds [Sat, 3 Nov 2018 17:34:03 +0000 (10:34 -0700)]
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mvsas: Remove set but not used variable 'id'
scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
scsi: qla2xxx: Remove a set-but-not-used variable
scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
scsi: qla2xxx: Declare local functions 'static'
scsi: qla2xxx: Improve several kernel-doc headers
scsi: qla2xxx: Modify fall-through annotations
scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
scsi: mvsas: Use dma_pool_zalloc
scsi: target: Don't request modules that aren't even built
scsi: target: Set response length for REPORT TARGET PORT GROUPS
Linus Torvalds [Sat, 3 Nov 2018 17:21:43 +0000 (10:21 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge more updates from Andrew Morton:
- more ocfs2 work
- various leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
memory_hotplug: cond_resched in __remove_pages
bfs: add sanity check at bfs_fill_super()
kernel/sysctl.c: remove duplicated include
kernel/kexec_file.c: remove some duplicated includes
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2: dlmglue: clean up timestamp handling
ocfs2: don't put and assigning null to bh allocated outside
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
ocfs2: don't use iocb when EIOCBQUEUED returns
ocfs2: without quota support, avoid calling quota recovery
ocfs2: remove ocfs2_is_o2cb_active()
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
include/linux/notifier.h: SRCU: fix ctags
mm: handle no memcg case in memcg_kmem_charge() properly
It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large. Fix the issue by calling
cond_resched once per memory section.
Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: Dan Williams <dan.j.williams@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tetsuo Handa [Fri, 2 Nov 2018 22:48:42 +0000 (15:48 -0700)]
bfs: add sanity check at bfs_fill_super()
syzbot is reporting too large memory allocation at bfs_fill_super() [1].
Since file system image is corrupted such that bfs_sb->s_start == 0,
bfs_fill_super() is trying to allocate 8MB of continuous memory. Fix
this by adding a sanity check on bfs_sb->s_start, __GFP_NOWARN and
printf().
Michal Hocko [Fri, 2 Nov 2018 22:48:31 +0000 (15:48 -0700)]
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
THP allocation mode is quite complex and it depends on the defrag mode.
This complexity is hidden in alloc_hugepage_direct_gfpmask from a large
part currently. The NUMA special casing (namely __GFP_THISNODE) is
however independent and placed in alloc_pages_vma currently. This both
adds an unnecessary branch to all vma based page allocation requests and
it makes the code more complex unnecessarily as well. Not to mention
that e.g. shmem THP used to do the node reclaiming unconditionally
regardless of the defrag mode until recently. This was not only
unexpected behavior but it was also hardly a good default behavior and I
strongly suspect it was just a side effect of the code sharing more than
a deliberate decision which suggests that such a layering is wrong.
Get rid of the thp special casing from alloc_pages_vma and move the
logic to alloc_hugepage_direct_gfpmask. __GFP_THISNODE is applied to the
resulting gfp mask only when the direct reclaim is not requested and
when there is no explicit numa binding to preserve the current logic.
Please note that there's also a slight difference wrt MPOL_BIND now. The
previous code would avoid using __GFP_THISNODE if the local node was
outside of policy_nodemask(). After this patch __GFP_THISNODE is avoided
for all MPOL_BIND policies. So there's a difference that if local node
is actually allowed by the bind policy's nodemask, previously
__GFP_THISNODE would be added, but now it won't be. From the behavior
POV this is still correct because the policy nodemask is used.
Link: http://lkml.kernel.org/r/20180925120326.24392-3-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Cc: Alex Williamson <alex.williamson@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Larry Chen [Fri, 2 Nov 2018 22:48:27 +0000 (15:48 -0700)]
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2_defrag_extent() might leak allocated clusters. When the file
system has insufficient space, the number of claimed clusters might be
less than the caller wants. If that happens, the original code might
directly commit the transaction without returning clusters.
This patch is based on code in ocfs2_add_clusters_in_btree().
[akpm@linux-foundation.org: include localalloc.h, reduce scope of data_ac] Link: http://lkml.kernel.org/r/20180904041621.16874-3-lchen@suse.com Signed-off-by: Larry Chen <lchen@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arnd Bergmann [Fri, 2 Nov 2018 22:48:23 +0000 (15:48 -0700)]
ocfs2: dlmglue: clean up timestamp handling
The handling of timestamps outside of the 1970..2038 range in the dlm
glue is rather inconsistent: on 32-bit architectures, this has always
wrapped around to negative timestamps in the 1902..1969 range, while on
64-bit kernels all timestamps are interpreted as positive 34 bit numbers
in the 1970..2514 year range.
Now that the VFS code handles 64-bit timestamps on all architectures, we
can make the behavior more consistent here, and return the same result
that we had on 64-bit already, making the file system y2038 safe in the
process. Outside of dlmglue, it already uses 64-bit on-disk timestamps
anway, so that part is fine.
For consistency, I'm changing ocfs2_pack_timespec() to clamp anything
outside of the supported range to the minimum and maximum values. This
avoids a possible ambiguity of values before 1970 in particular, which
used to be interpreted as times at the end of the 2514 range previously.
Link: http://lkml.kernel.org/r/20180619155826.4106487-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:19 +0000 (15:48 -0700)]
ocfs2: don't put and assigning null to bh allocated outside
ocfs2_read_blocks() and ocfs2_read_blocks_sync() are both used to read
several blocks from disk. Currently, the input argument *bhs* can be
NULL or NOT. It depends on the caller's behavior. If the function
fails in reading blocks from disk, the corresponding bh will be assigned
to NULL and put.
Obviously, above process for non-NULL input bh is not appropriate.
Because the caller doesn't even know its bhs are put and re-assigned.
If buffer head is managed by caller, ocfs2_read_blocks and
ocfs2_read_blocks_sync() should not evaluate it to NULL. It will cause
caller accessing illegal memory, thus crash.
Link: http://lkml.kernel.org/r/HK2PR06MB045285E0F4FBB561F9F2F9B3D5680@HK2PR06MB0452.apcprd06.prod.outlook.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Guozhonghua <guozhonghua@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:15 +0000 (15:48 -0700)]
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
Somehow, file system metadata was corrupted, which causes
ocfs2_check_dir_entry() to fail in function ocfs2_dir_foreach_blk_el().
According to the original design intention, if above happens we should
skip the problematic block and continue to retrieve dir entry. But
there is obviouse misuse of brelse around related code.
After failure of ocfs2_check_dir_entry(), current code just moves to
next position and uses the problematic buffer head again and again
during which the problematic buffer head is released for multiple times.
I suppose, this a serious issue which is long-lived in ocfs2. This may
cause other file systems which is also used in a the same host insane.
So we should also consider about bakcporting this patch into linux
-stable.
Link: http://lkml.kernel.org/r/HK2PR06MB045211675B43EED794E597B6D56E0@HK2PR06MB0452.apcprd06.prod.outlook.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Suggested-by: Changkuo Shi <shi.changkuo@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changwei Ge [Fri, 2 Nov 2018 22:48:11 +0000 (15:48 -0700)]
ocfs2: don't use iocb when EIOCBQUEUED returns
When -EIOCBQUEUED returns, it means that aio_complete() will be called
from dio_complete(), which is an asynchronous progress against
write_iter. Generally, IO is a very slow progress than executing
instruction, but we still can't take the risk to access a freed iocb.
And we do face a BUG crash issue. Using the crash tool, iocb is
obviously freed already.
And the backtrace shows:
ocfs2_file_write_iter+0xcaa/0xd00 [ocfs2]
aio_run_iocb+0x229/0x2f0
do_io_submit+0x291/0x540
SyS_io_submit+0x10/0x20
system_call_fastpath+0x16/0x75
Link: http://lkml.kernel.org/r/1523361653-14439-1-git-send-email-ge.changwei@h3c.com Signed-off-by: Changwei Ge <ge.changwei@h3c.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Guozhonghua [Fri, 2 Nov 2018 22:48:07 +0000 (15:48 -0700)]
ocfs2: without quota support, avoid calling quota recovery
During one dead node's recovery by other node, quota recovery work will
be queued. We should avoid calling quota when it is not supported, so
check the quota flags.
Link: http://lkml.kernel.org/r/71604351584F6A4EBAE558C676F37CA401071AC9FB@H3CMLB12-EX.srv.huawei-3com.com Signed-off-by: guozhonghua <guozhonghua@h3c.com> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <ge.changwei@h3c.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gang He [Fri, 2 Nov 2018 22:48:03 +0000 (15:48 -0700)]
ocfs2: remove ocfs2_is_o2cb_active()
Remove ocfs2_is_o2cb_active(). We have similar functions to identify
which cluster stack is being used via osb->osb_cluster_stack.
Secondly, the current implementation of ocfs2_is_o2cb_active() is not
totally safe. Based on the design of stackglue, we need to get
ocfs2_stack_lock before using ocfs2_stack related data structures, and
that active_stack pointer can be NULL in the case of mount failure.
Link: http://lkml.kernel.org/r/1495441079-11708-1-git-send-email-ghe@suse.com Signed-off-by: Gang He <ghe@suse.com> Reviewed-by: Joseph Qi <jiangqi903@gmail.com> Reviewed-by: Eric Ren <zren@suse.com> Acked-by: Changwei Ge <ge.changwei@h3c.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
THP allocation might be really disruptive when allocated on NUMA system
with the local node full or hard to reclaim. Stefan has posted an
allocation stall report on 4.12 based SLES kernel which suggests the
same issue:
The defrag mode is "madvise" and from the above report it is clear that
the THP has been allocated for MADV_HUGEPAGA vma.
Andrea has identified that the main source of the problem is
__GFP_THISNODE usage:
: The problem is that direct compaction combined with the NUMA
: __GFP_THISNODE logic in mempolicy.c is telling reclaim to swap very
: hard the local node, instead of failing the allocation if there's no
: THP available in the local node.
:
: Such logic was ok until __GFP_THISNODE was added to the THP allocation
: path even with MPOL_DEFAULT.
:
: The idea behind the __GFP_THISNODE addition, is that it is better to
: provide local memory in PAGE_SIZE units than to use remote NUMA THP
: backed memory. That largely depends on the remote latency though, on
: threadrippers for example the overhead is relatively low in my
: experience.
:
: The combination of __GFP_THISNODE and __GFP_DIRECT_RECLAIM results in
: extremely slow qemu startup with vfio, if the VM is larger than the
: size of one host NUMA node. This is because it will try very hard to
: unsuccessfully swapout get_user_pages pinned pages as result of the
: __GFP_THISNODE being set, instead of falling back to PAGE_SIZE
: allocations and instead of trying to allocate THP on other nodes (it
: would be even worse without vfio type1 GUP pins of course, except it'd
: be swapping heavily instead).
Fix this by removing __GFP_THISNODE for THP requests which are
requesting the direct reclaim. This effectivelly reverts 5265047ac301
on the grounds that the zone/node reclaim was known to be disruptive due
to premature reclaim when there was memory free. While it made sense at
the time for HPC workloads without NUMA awareness on rare machines, it
was ultimately harmful in the majority of cases. The existing behaviour
is similar, if not as widespare as it applies to a corner case but
crucially, it cannot be tuned around like zone_reclaim_mode can. The
default behaviour should always be to cause the least harm for the
common case.
If there are specialised use cases out there that want zone_reclaim_mode
in specific cases, then it can be built on top. Longterm we should
consider a memory policy which allows for the node reclaim like behavior
for the specific memory ranges which would allow a
: Both patches look correct to me but I'm responding to this one because
: it's the fix. The change makes sense and moves further away from the
: severe stalling behaviour we used to see with both THP and zone reclaim
: mode.
:
: I put together a basic experiment with usemem configured to reference a
: buffer multiple times that is 80% the size of main memory on a 2-socket
: box with symmetric node sizes and defrag set to "always". The defrag
: setting is not the default but it would be functionally similar to
: accessing a buffer with madvise(MADV_HUGEPAGE). Usemem is configured to
: reference the buffer multiple times and while it's not an interesting
: workload, it would be expected to complete reasonably quickly as it fits
: within memory. The results were;
:
: usemem
: vanilla noreclaim-v1
: Amean Elapsd-1 42.78 ( 0.00%) 26.87 ( 37.18%)
: Amean Elapsd-3 27.55 ( 0.00%) 7.44 ( 73.00%)
: Amean Elapsd-4 5.72 ( 0.00%) 5.69 ( 0.45%)
:
: This shows the elapsed time in seconds for 1 thread, 3 threads and 4
: threads referencing buffers 80% the size of memory. With the patches
: applied, it's 37.18% faster for the single thread and 73% faster with two
: threads. Note that 4 threads showing little difference does not indicate
: the problem is related to thread counts. It's simply the case that 4
: threads gets spread so their workload mostly fits in one node.
:
: The overall view from /proc/vmstats is more startling
:
: 4.19.0-rc1 4.19.0-rc1
: vanillanoreclaim-v1r1
: Minor Faults 35593425 708164
: Major Faults 484088 36
: Swap Ins 3772837 0
: Swap Outs 3932295 0
:
: Massive amounts of swap in/out without the patch
:
: Direct pages scanned 6013214 0
: Kswapd pages scanned 0 0
: Kswapd pages reclaimed 0 0
: Direct pages reclaimed 4033009 0
:
: Lots of reclaim activity without the patch
:
: Kswapd efficiency 100% 100%
: Kswapd velocity 0.000 0.000
: Direct efficiency 67% 100%
: Direct velocity 11191.956 0.000
:
: Mostly from direct reclaim context as you'd expect without the patch.
:
: Page writes by reclaim 3932314.000 0.000
: Page writes file 19 0
: Page writes anon 3932295 0
: Page reclaim immediate 42336 0
:
: Writes from reclaim context is never good but the patch eliminates it.
:
: We should never have default behaviour to thrash the system for such a
: basic workload. If zone reclaim mode behaviour is ever desired but on a
: single task instead of a global basis then the sensible option is to build
: a mempolicy that enforces that behaviour.
This was a severe regression compared to previous kernels that made
important workloads unusable and it starts when __GFP_THISNODE was
added to THP allocations under MADV_HUGEPAGE. It is not a significant
risk to go to the previous behavior before __GFP_THISNODE was added, it
worked like that for years.
This was simply an optimization to some lucky workloads that can fit in
a single node, but it ended up breaking the VM for others that can't
possibly fit in a single node, so going back is safe.
[mhocko@suse.com: rewrote the changelog based on the one from Andrea] Link: http://lkml.kernel.org/r/20180925120326.24392-2-mhocko@kernel.org Fixes: 5265047ac301 ("mm, thp: really limit transparent hugepage allocation to local node") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Stefan Priebe <s.priebe@profihost.ag> Debugged-by: Andrea Arcangeli <aarcange@redhat.com> Reported-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Mel Gorman <mgorman@techsingularity.net> Tested-by: Mel Gorman <mgorman@techsingularity.net> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: David Rientjes <rientjes@google.com> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: <stable@vger.kernel.org> [4.1+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sam Protsenko [Fri, 2 Nov 2018 22:47:53 +0000 (15:47 -0700)]
include/linux/notifier.h: SRCU: fix ctags
ctags indexing ("make tags" command) throws this warning:
ctags: Warning: include/linux/notifier.h:125:
null expansion of name pattern "\1"
This is the result of DEFINE_PER_CPU() macro expansion. Fix that by
getting rid of line break.
Similar fix was already done in commit 25528213fe9f ("tags: Fix
DEFINE_PER_CPU expansions"), but this one probably wasn't noticed.
Link: http://lkml.kernel.org/r/20181030202808.28027-1-semen.protsenko@linaro.org Fixes: 9c80172b902d ("kernel/SRCU: provide a static initializer") Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Fri, 2 Nov 2018 22:47:49 +0000 (15:47 -0700)]
mm: handle no memcg case in memcg_kmem_charge() properly
Mike Galbraith reported a regression caused by the commit 9b6f7e163cd0
("mm: rework memcg kernel stack accounting") on a system with
"cgroup_disable=memory" boot option: the system panics with the following
stack trace:
The problem occurs because get_mem_cgroup_from_current() returns the NULL
pointer if memory controller is disabled. Let's check if this is a case
at the beginning of memcg_kmem_charge() and just return 0 if
mem_cgroup_disabled() returns true. This is how we handle this case in
many other places in the memory controller code.
Link: http://lkml.kernel.org/r/20181029215123.17830-1-guro@fb.com Fixes: 9b6f7e163cd0 ("mm: rework memcg kernel stack accounting") Signed-off-by: Roman Gushchin <guro@fb.com> Reported-by: Mike Galbraith <efault@gmx.de> Acked-by: Rik van Riel <riel@surriel.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Shakeel Butt <shakeelb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
Remove unused parameter from HASH1 dmas property on stm32mp157c SoC.
Fixes: 1e726a40e067 ("ARM: dts: stm32: Add HASH support on stm32mp157c") Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[Olof: Bug doesn't cause any harm, so shouldn't need stable backport] Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Fri, 5 Oct 2018 16:15:49 +0000 (18:15 +0200)]
ARM: orion: avoid VLA in orion_mpp_conf
Testing randconfig builds found an instance of a VLA that was
missed when determining that we have removed them all:
arch/arm/plat-orion/mpp.c: In function 'orion_mpp_conf':
arch/arm/plat-orion/mpp.c:31:2: error: ISO C90 forbids variable length array 'mpp_ctrl' [-Werror=vla]
This one is fairly straightforward: we know what all three
callers are, and the maximum length is not very long.
Marc Zyngier [Fri, 2 Nov 2018 17:16:51 +0000 (17:16 +0000)]
iov_iter: Fix 9p virtio breakage
When switching to the new iovec accessors, a negation got subtly
dropped, leading to 9p being remarkably broken (here with kvmtool):
[ 7.430941] VFS: Mounted root (9p filesystem) on device 0:15.
[ 7.432080] devtmpfs: mounted
[ 7.432717] Freeing unused kernel memory: 1344K
[ 7.433658] Run /virt/init as init process
Warning: unable to translate guest address 0x7e00902ff000 to host
Warning: unable to translate guest address 0x7e00902fefc0 to host
Warning: unable to translate guest address 0x7e00902ff000 to host
Warning: unable to translate guest address 0x7e008febef80 to host
Warning: unable to translate guest address 0x7e008febf000 to host
Warning: unable to translate guest address 0x7e008febef00 to host
Warning: unable to translate guest address 0x7e008febf000 to host
[ 7.436376] Kernel panic - not syncing: Requested init /virt/init failed (error -8).
[ 7.437554] CPU: 29 PID: 1 Comm: swapper/0 Not tainted 4.19.0-rc8-02267-g00e23707442a #291
[ 7.439006] Hardware name: linux,dummy-virt (DT)
[ 7.439902] Call trace:
[ 7.440387] dump_backtrace+0x0/0x148
[ 7.441104] show_stack+0x14/0x20
[ 7.441768] dump_stack+0x90/0xb4
[ 7.442425] panic+0x120/0x27c
[ 7.443036] kernel_init+0xa4/0x100
[ 7.443725] ret_from_fork+0x10/0x18
[ 7.444444] SMP: stopping secondary CPUs
[ 7.445391] Kernel Offset: disabled
[ 7.446169] CPU features: 0x0,23000438
[ 7.446974] Memory Limit: none
[ 7.447645] ---[ end Kernel panic - not syncing: Requested init /virt/init failed (error -8). ]---
Restoring the missing "!" brings the guest back to life.
Fixes: 00e23707442a ("iov_iter: Use accessor function") Reported-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Steve French [Thu, 1 Nov 2018 15:54:32 +0000 (10:54 -0500)]
cifs: fix signed/unsigned mismatch on aio_read patch
The patch "CIFS: Add support for direct I/O read" had
a signed/unsigned mismatch (ssize_t vs. size_t) in the
return from one function. Similar trivial change
in aio_write
Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Colin Ian King [Thu, 1 Nov 2018 13:14:30 +0000 (13:14 +0000)]
cifs: don't dereference smb_file_target before null check
There is a null check on dst_file->private data which suggests
it can be potentially null. However, before this check, pointer
smb_file_target is derived from dst_file->private and dereferenced
in the call to tlink_tcon, hence there is a potential null pointer
deference.
Fix this by assigning smb_file_target and target_tcon after the
null pointer sanity checks.
Detected by CoverityScan, CID#1475302 ("Dereference before null check")
Fixes: 04b38d601239 ("vfs: pull btrfs clone API to vfs layer") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Long Li [Wed, 31 Oct 2018 22:13:11 +0000 (22:13 +0000)]
CIFS: Add direct I/O functions to file_operations
With direct read/write functions implemented, add them to file_operations.
Dircet I/O is used under two conditions:
1. When mounting with "cache=none", CIFS uses direct I/O for all user file
data transfer.
2. When opening a file with O_DIRECT, CIFS uses direct I/O for all data
transfer on this file.
Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Steve French [Wed, 31 Oct 2018 00:50:31 +0000 (19:50 -0500)]
smb3: allow more detailed protocol info on open files for debugging
In order to debug complex problems it is often helpful to
have detailed information on the client and server view
of the open file information. Add the ability for root to
view the list of smb3 open files and dump the persistent
handle and other info so that it can be more easily
correlated with server logs.
Steve French [Sun, 28 Oct 2018 18:13:23 +0000 (13:13 -0500)]
smb3: on kerberos mount if server doesn't specify auth type use krb5
Some servers (e.g. Azure) do not include a spnego blob in the SMB3
negotiate protocol response, so on kerberos mounts ("sec=krb5")
we can fail, as we expected the server to list its supported
auth types (OIDs in the spnego blob in the negprot response).
Change this so that on krb5 mounts we default to trying krb5 if the
server doesn't list its supported protocol mechanisms.
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org>
Steve French [Sun, 28 Oct 2018 05:47:11 +0000 (00:47 -0500)]
smb3: add trace point for tree connection
In debugging certain scenarios, especially reconnect cases,
it can be helpful to have a dynamic trace point for the
result of tree connect. See sample output below
from a reconnect event. The new event is 'smb3_tcon'
Ronnie Sahlberg [Thu, 25 Oct 2018 05:43:36 +0000 (15:43 +1000)]
cifs: fix return value for cifs_listxattr
If the application buffer was too small to fit all the names
we would still count the number of bytes and return this for
listxattr. This would then trigger a BUG in usercopy.c
Fix the computation of the size so that we return -ERANGE
correctly when the buffer is too small.
This fixes the kernel BUG for xfstest generic/377
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com>
Guo Ren [Fri, 2 Nov 2018 16:51:28 +0000 (00:51 +0800)]
clocksource/drivers/c-sky: Add C-SKY SMP timer
The driver is for C-SKY SMP timer. It only supports oneshot event
and 32bit overflow for clocksource. Per cpu core has one timer and
all timers share one clock-counter-input from the same clocksource.
This use mfcr&mtcr instructions to access the regs.
Signed-off-by: Guo Ren <ren_guo@c-sky.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
__swiotlb_get_sgtable_page and __swiotlb_mmap_pfn are not only misnamed
but also only used if CONFIG_IOMMU_DMA is set. Just add a simple ifdef
for now, given that we plan to remove them entirely for the next merge
window.
Reported-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Will Deacon <will.deacon@arm.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Fri, 2 Nov 2018 18:25:48 +0000 (11:25 -0700)]
Merge tag 'for-linus-20181102' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"The biggest part of this pull request is the revert of the blkcg
cleanup series. It had one fix earlier for a stacked device issue, but
another one was reported. Rather than play whack-a-mole with this,
revert the entire series and try again for the next kernel release.
Apart from that, only small fixes/changes.
Summary:
- Indentation fixup for mtip32xx (Colin Ian King)
- The blkcg cleanup series revert (Dennis Zhou)
- Two NVMe fixes. One fixing a regression in the nvme request
initialization in this merge window, causing nvme-fc to not work.
The other is a suspend/resume p2p resource issue (James, Keith)
- Fix sg discard merge, allowing us to merge in cases where we didn't
before (Jianchao Wang)
- Call rq_qos_exit() after the queue is frozen, preventing a hang
(Ming)
- Fix brd queue setup, fixing an oops if we fail setting up all
devices (Ming)"
* tag 'for-linus-20181102' of git://git.kernel.dk/linux-block:
nvme-pci: fix conflicting p2p resource adds
nvme-fc: fix request private initialization
blkcg: revert blkcg cleanups series
block: brd: associate with queue until adding disk
block: call rq_qos_exit() after queue is frozen
mtip32xx: clean an indentation issue, remove extraneous tabs
block: fix the DISCARD request merge
Linus Torvalds [Fri, 2 Nov 2018 18:22:45 +0000 (11:22 -0700)]
Merge tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This series contains a number of improvements to existing drivers,
such as LPSS. Some drivers, such as renesas-tpu and rcar get support
for more SoC generations. To round things off this fixes an issue with
the sysfs interface"
* tag 'pwm/for-4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: Only set update bit if we are actually changing the settings
pwm: lpss: Force runtime-resume on suspend on Cherry Trail
pwm: Enable TI ECAP driver for ARCH_K3
dt-bindings: pwm: tiecap: Add TI AM654 SoC specific compatible
dt-bindings: pwm: rcar: Add r8a774a1 support
pwm: Send a uevent on the pwmchip device upon channel sysfs (un)export
Revert "pwm: Set class for exported channels in sysfs"
dt-bindings: pwm: renesas-tpu: Document r8a7744 support
dt-bindings: pwm: rcar: Add r8a7744 support
dt-bindings: pwm: renesas: tpu: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: pwm-rcar: Document R8A779{7|8}0 bindings
dt-bindings: pwm: renesas: tpu: Fix "compatible" prop description
pwm: Use SPDX identifier for Renesas drivers
pwm: lpss: Add get_state callback
pwm: lpss: Release runtime-pm reference from the driver's remove callback
pwm: lpss: Check PWM powerstate after resume on Cherry Trail devices
pwm: lpss: Move struct pwm_lpss_chip definition to the header file
pwm: lpss: Add ACPI HID for second PWM controller on Cherry Trail devices
ACPI / PM: Export acpi_device_get_power() for use by modular build drivers
pwm: tegra: Remove gratuituous blank line
Marc Zyngier [Wed, 31 Oct 2018 08:41:34 +0000 (08:41 +0000)]
soc: ti: QMSS: Fix usage of irq_set_affinity_hint
The Keystone QMSS driver is pretty damaged, in the sense that it
does things like this:
irq_set_affinity_hint(irq, to_cpumask(&cpu_map));
where cpu_map is a local variable. As we leave the function, this
will point to nowhere-land, and things will end-up badly.
Instead, let's use a proper cpumask that gets allocated, giving
the driver a chance to actually work with things like irqbalance
as well as have a hypothetical 64bit future.
Cc: stable@vger.kernel.org Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Fri, 2 Nov 2018 18:17:22 +0000 (11:17 -0700)]
Merge tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull more EDAC updates from Borislav Petkov:
"The second part of the EDAC pile which contains the ADXL user and a
build fix which addresses a not-so-sensical .config but fixes
randconfig builds people do:
- skx_edac: Address translation for NVDIMMs (Tony Luck and Qiuxu Zhuo)
- ACPI_ADXL build fix"
[ I don't think "sensical" is a word, particularly when used in the
context of actually meaning "nonsensical", but I like it - Linus ]
* tag 'edac_for_4.20_2' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, skx: Fix randconfig builds
EDAC, skx_edac: Add address translation for non-volatile DIMMs