usb-storage: CY7C68300A chips do not support Cypress ATACB
Many cards based on CY7C68300A/B/C use the USB ID 04b4:6830 but only the
B and C variants (EZ-USB AT2LP) support the ATA Command Block
functionality, according to the data sheets. The A variant (EZ-USB AT2)
locks up if ATACB is attempted, until a typical 30 seconds timeout runs
out and a USB reset is performed.
https://bugs.launchpad.net/bugs/428469
It seems that one way to spot a CY7C68300A (at least where the card
manufacturer left Cypress' EEPROM default vaules, against Cypress'
recommendations) is to look at the USB string descriptor indices.
A http://media.digikey.com/pdf/Data%20Sheets/Cypress%20PDFs/CY7C68300A.pdf
B http://www.farnell.com/datasheets/43456.pdf
C http://www.cypress.com/?rID=14189
Note that a CY7C68300B/C chip appears as CY7C68300A if it is running
in Backward Compatibility Mode, and if ATACB would be supported in this
case there is anyway no way to tell which chip it really is.
For 5 years my external USB drive has been locking up for half a minute
when plugged in and ata_id is run by udev, or anytime hdparm or similar
is run on it.
Finally looking at the /correct/ datasheet I think I found the reason. I
am aware the quirk in this patch is a bit hacky, but the hardware
manufacturers haven't made it easy for us.
Adrian Thomasset [Tue, 23 Apr 2013 11:46:29 +0000 (12:46 +0100)]
USB: ftdi_sio: correct ST Micro Connect Lite PIDs
The current ST Micro Connect Lite uses the FT4232H hi-speed quad USB
UART FTDI chip. It is also possible to drive STM reference targets
populated with an on-board JTAG debugger based on the FT2232H chip with
the same STMicroelectronics tools.
For this reason, the ST Micro Connect Lite PIDs should be
ST_STMCLT_2232_PID: 0x3746
ST_STMCLT_4232_PID: 0x3747
Shawn Guo [Sun, 24 Mar 2013 14:06:05 +0000 (22:06 +0800)]
ARM: mxs_defconfig: add CONFIG_USB_PHY
Commit edc7cb2 (usb: phy: make it a menuconfig) makes USB_MXS_PHY
be a sub-item of menuconfig symbol USB_PHY. This change gets the
selection of CONFIG_USB_MXS_PHY in mxs_defconfig lost. Hence the
boot stops at the point below.
[ 1.600867] ci_hdrc ci_hdrc.0: doesn't support gadget
[ 1.606282] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 1.613522] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
Add CONFIG_USB_PHY to have the CONFIG_USB_MXS_PHY selection back to
work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
Shawn Guo [Sun, 24 Mar 2013 14:06:04 +0000 (22:06 +0800)]
ARM: imx_v6_v7_defconfig: add CONFIG_USB_PHY
Commit edc7cb2 (usb: phy: make it a menuconfig) makes USB_MXS_PHY
be a sub-item of menuconfig symbol USB_PHY. This change gets the
selection of CONFIG_USB_MXS_PHY in imx_v6_v7_defconfig lost. Hence the
boot stops at the point below.
ci_hdrc ci_hdrc.0: doesn't support gadget
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
Add CONFIG_USB_PHY to have the CONFIG_USB_MXS_PHY selection back to
work.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: zero: put function instances on unbind
If function instances are not put on gadget's unbind, their implementation
module's refcount is nonzero and it is impossible to unload them.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
usb: gadget: f_sourcesink.c: correct a copy-paste misnomer
acm was the first function to be converted and it seems that its
code served as a base for converting f_sourcesink to the new function
interface. source_sink has nothing to do with acm, though.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
Now that Joe cleaned up the init/exit functions, we can just get rid of
them entirely and use the proper macro that almost all other USB drivers
now use.
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Cc: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Joe Perches [Fri, 19 Apr 2013 18:44:00 +0000 (11:44 -0700)]
usb: storage: Convert US_DEBUGP to usb_stor_dbg
Use a more current logging style with dev_printk
where possible.
o Convert uses of US_DEBUGP to usb_stor_dbg
o Add "struct us_data *" to usb_stor_dbg uses
o usb_stor_dbg now uses struct device */dev_vprint_emit
o Removed embedded function names
o Coalesce formats
o Remove trailing whitespace
o Remove useless OOM messages
o Remove useless function entry/exit logging
o Convert some US_DEBUGP uses to dev_info and dev_dbg
Object size is slightly reduced when debugging
is enabled, slightly increased with no debugging
because some initialization and removal messages
are now always emitted.
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 18 Apr 2013 15:33:17 +0000 (17:33 +0200)]
USB: io_ti: fix TIOCGSERIAL
Fix regression introduced by commit f40d78155 ("USB: io_ti: kill custom
closing_wait implementation") which made TIOCGSERIAL return the wrong
value for closing_wait.
Ming Lei [Thu, 18 Apr 2013 04:17:38 +0000 (12:17 +0800)]
USB: usbtmc: remove unnecessary memory allocation
Inside usbtmc_ioctl_clear_out_halt()/usbtmc_ioctl_clear_in_halt(),
usb_clear_halt() needn't any buffer to pass in, so remove the
unnecessary memory allocation.
Signed-off-by: Ming Lei <ming.lei@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 16 Apr 2013 16:01:27 +0000 (18:01 +0200)]
USB: mct_u232: clean up read implementation
The device uses the second interrupt-in endpoint of the interface for
reading. Stop abusing the port read urb and store a pointer to the
second interrupt-in urb as port-private data instead.
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Quadros [Mon, 15 Apr 2013 11:50:34 +0000 (14:50 +0300)]
USB: ehci-omap: Don't select any PHY driver
Don't select NOP_USB_XCEIV. Instead, board config
must select USB_PHY and the appropriate PHY driver.
Also add a hint in Kconfig so that users enabling
this driver manually enable the right PHY drivers as well.
Gets rid of the below warnings when USB_EHCI_HCD_OMAP
is enabled.
warning: (USB_EHCI_HCD_OMAP) selects NOP_USB_XCEIV which has unmet direct dependencies (USB_SUPPORT && USB_PHY)
warning: (USB_EHCI_HCD_OMAP) selects NOP_USB_XCEIV which has unmet direct dependencies (USB_SUPPORT && USB_PHY)
Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 16 Apr 2013 09:08:33 +0000 (11:08 +0200)]
usbfs: Always allow ctrl requests with USB_RECIP_ENDPOINT on the ctrl ep
When usbfs receives a ctrl-request from userspace it calls check_ctrlrecip,
which for a request with USB_RECIP_ENDPOINT tries to map this to an interface
to see if this interface is claimed, except for ctrl-requests with a type of
USB_TYPE_VENDOR.
When trying to use this device: http://www.akaipro.com/eiepro
redirected to a Windows vm running on qemu on top of Linux.
The windows driver makes a ctrl-req with USB_TYPE_CLASS and
USB_RECIP_ENDPOINT with index 0, and the mapping of the endpoint (0) to
the interface fails since ep 0 is the ctrl endpoint and thus never is
part of an interface.
This patch fixes this ctrl-req failing by skipping the checkintf call for
USB_RECIP_ENDPOINT ctrl-reqs on the ctrl endpoint.
Reported-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl> Tested-by: Dave Stikkolorum <d.r.stikkolorum@hhs.nl> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shengzhou Liu [Wed, 17 Apr 2013 10:03:46 +0000 (18:03 +0800)]
usb: remove redundant tdi_reset
We remove the redundant tdi_reset in ehci_setup since there
is already it in ehci_reset.
It was observed that the duplicated tdi_reset was causing
the PHY_CLK_VALID bit unstable.
Reported-by: Michael Braun <michael-dev@fami-braun.de> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@vger.kernel.org> # 3.6+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb-serial: add support for USB Wishbone-serial adapters
Wishbone is an open hardware SoC bus commonly used in FPGA
designs. Bus access can be serialized using the Etherbone
protocol <http://www.ohwr.org/projects/etherbone-core>.
This driver is intended to be used with devices which attach
their internal Wishbone bus to a USB serial interface using
the Etherbone protocol. A userspace library is required to
speak the protocol made available by this driver as ttyUSBx.
Signed-off-by: Wesley W. Terpstra <w.terpstra@gsi.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB: enclose all depends on USB_OHCI_HCD within an if USB_OHCI_HCD block
This patch removes the various depends on USB_OHCI_HCD from the OHCI HCD
drivers and enclose them within an if USB_OHCI_HCD / endif block. The
Octeon OHCI HCD driver has been moved around to remain in this block.
USB: enclose EHCI HCD drivers within an if USB_EHCI_HCD block
Thist patch removes the depends on USB_EHCI_HCD that the various USB
EHCI HCD drivers use and encloses every driver within an if USB_EHCI_HCD
/ endif block. The EHCI HCD platform and Octeon drivers have been moved
around to remain enclosed within this block.
USB: remove USB_EHCI_BIG_ENDIAN_{DESC,MMIO} depends on architecture symbol
Just like the OHCI counter part we just can remove the architecture
specific symbols which prevent these configuration symbols from being
selected by platforms/architectures requiring it. The original
implementation did not scale at all since it required each and every
single architecture to be added for these configuration symbols to be
selected. Now it is up to the EHCI driver and/or platform to select
these configuration symbols accordingly.
USB: regroup all depends on USB within an if USB block
This patch removes the depends on USB from all config symbols in
drivers/usb/host/Kconfig and replace that with an if USB / endif block
as suggested by Alan Stern. Some source ... Kconfig lines have been
shuffled around to permit a better regroupment of the Kconfig files
depending on "config USB" item. No functionnal change is introduced.
7edb3da: (USB: EHCI: make ehci-s5p a separate driver)
raised an issue with ehci-s5p's driver data.
Now that 's5p_ehci_hcd' doesn't maintain pointer to 'usb_hcd'
and s5p_ehci is nothing but a pointer to hcd->priv;
add hcd to the driver data rather than s5p_ehci.
This fixes issues with null pointer dereferencing in
s5p_ehci_shutdown(), s5p_ehci_suspend(), s5p_ehci_resume().
Merge tag 'for-usb-next-2012-04-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xHCI misc cleanup patches for 3.10
Hi Greg,
Here's three cleanup patches for 3.10. Nothing big here, just some debugging
output changes, a macro rename, and a math macro change that should have no
behavioral effects.
Tested on the Intel Panther Point xHCI host, with USB storage and mouse, with
xHCI debugging turned on. I don't have the TI host that causes the debugging
output changes to trigger.
Separate the Qualcomm QSD/MSM on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before Qualcomm QSD/MSM
can be booted with a multi-platform kernel, which is not expected before
3.11.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the msm bus glue.
In V5 (arnd):
- add FIXME about missing usb_add_hcd() or usb_remove_hcd() calls
In V3:
- Detailed commit message added here describing why this patch is required.
- Arranged #include's in alphabetical order.
- driver.name initialized hcd_name[] = "ehci-msm" in platform_driver
structure initialization instead of "msm-ehci", which was the reason
why it broke in EHCI USB testing
In V2:
Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brown <davidb@codeaurora.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Atmel host controller driver from ehci-hcd host code
so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before Atmel can be
booted with a multi-platform kernel. This is currently planned for
Linux-3.11.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the Atmel bus glue.
In V4 (arnd):
- reordered #include statements.
- removed call to ehci_shutdown and the corresponding export
In V3:
- Detailed commit message added here about why this patch is required.
- Replaced hcd_name string "ehci-atmel" to "atmel-ehci".
- Inserted blank line in the Makefile to separate the EHCI drivers from
the following non-EHCI drivers.
- Exported ehci_shutdown symbol as it is needed by the Atmel driver.
- Eliminated ehci_atmel_setup routine because hcd registers
can be directly set in the ehci_atmel_drv_probe function.
In V2:
Resolved below compiler error.
drivers/usb/host/ehci-atmel.c: In function 'ehci_atmel_drv_remove':
drivers/usb/host/ehci-atmel.c:167: error: implicit declaration of function 'ehci_shutdown'
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: Andrew Victor <linux@maxim.org.za> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung S5P/EXYNOS host controller driver from ehci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before S5P/EXYNOS can
be booted with a multi-platform kernel. We currently expect those
to get merged for 3.10.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the s5p bus glue.
In V4 (arnd)
- revert some of the pointless changes.
- fix allocation of s5p specific data structure.
In V3:
- Detailed commit message added here, why this patch is required.
- MODULE_LICENSE is GPL v2.
- Added .extra_priv_size to eliminate the separate allocation of
the s5p_ehci_hcd structure and removed .reset function pointer
initialization.
- Arranged #include's in alphabetical order.
- After using extra_priv_size initialization, struct usb_hcd *hcd
is redundant and can be removed from the probe function.
- Eliminated s5p_ehci_phy_enable,contents of statements moved
into the s5p_ehci_probe
- Eliminated s5p_ehci_phy_disable, contents of statements moved into
the s5p_ehci_remove.
In V2:
- Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Acked-by: Jingoo Han <jg1.han@samsung.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the SPEAr host controller driver from ehci-hcd host code
so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before SPEAr can be
booted with a multi-platform kernel, but they are queued in the
arm-soc tree for 3.10.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the SPEAr bus glue.
In V4 (arnd):
- renamed all 'struct spear_ehci' pointers from 'ehci' to the
less ambiguous 'sehci'.
- folded trivial spear_start_ehci/spear_stop_ehci functions into
callers.
- brought back initialization of ehci->caps.
In V3:
- Detailed commit message added here about why this patch is required.
- Eliminated ehci_spear_setup routine because hcd registers can
be directly set in the spear_ehci_hcd_drv_probe function.
- spear_overrides struct initialized.
- Converted to using .extra_priv_size for allocating spear_ehci,
and updated all users of that structure.
- to_spear_ehci() macro modified for spear_ehci.
In V2:
- Replaced spear as SPEAr everywhere, leaving functions/variables/config options.
Separate the Orion host controller driver from ehci-hcd host
code into its own driver module because of following reason.
With the multiplatform changes in arm-soc tree, it becomes
possible to enable the mvebu platform (which uses
ehci-orion) at the same time as other platforms that require
a conflicting EHCI bus glue. At the moment, this results
in a warning like
drivers/usb/host/ehci-hcd.c:1297:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1277:0: note: this is the location of the previous definition
drivers/usb/host/ehci-orion.c:334:31: warning: 'ehci_orion_driver' defined but not used [-Wunused-variable]
and an ehci driver that only works on one of them.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the orion bus glue.
An earlier version of this patch was included in 3.9 but caused
a regression there, which has subsequently been fixed.
While we are here, use the opportunity to disabiguate the two
Marvell EHCI controller implementations in Kconfig.
In V4 (arnd):
- Improve Kconfig text
In V3:
- More detail provided in commit message regarding this patch.
- Replaced hcd_name string "ehci-orion" into "orion-ehci".
- MODULE_LICENSE is GPL v2.
- In ehci_init_driver calling second argument passed as NULL instead of
ehci_orion_overrides because ehci_orion_overrides is removed.
In V2:
- Tegra patch related changes removed from this patch.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jason Cooper <jason@lakedaemon.net> Tested-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Rientjes [Sun, 7 Apr 2013 21:11:47 +0000 (14:11 -0700)]
usb, gadget: use appropriate warning accessors
Use the appropriate WARN() and WARN_ON() accessors to avoid a build error
when CONFIG_BUG=n:
drivers/usb/gadget/configfs.c: In function 'config_usb_cfg_unlink':
drivers/usb/gadget/configfs.c:442:2: error: implicit declaration of function '__WARN_printf'
drivers/usb/gadget/configfs.c: In function 'configfs_do_nothing':
drivers/usb/gadget/configfs.c:733:2: error: implicit declaration of function '__WARN'
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David Rientjes <rientjes@google.com> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Camuso [Fri, 5 Apr 2013 18:27:07 +0000 (14:27 -0400)]
xhci - clarify compliance mode debug messages
There are no functional changes in this patch. However, because the
compliance mode timer can be deleted in more than one function, it
seemed expedient to include the function name in the debug strings.
Also limited the use of capitals to the first word in the compliance
mode debug messages, except after a function name where all words
start with lower case, in keeping with the style prevalent elsewhere
in xhci.c.
Signed-off-by: Tony Camuso <tcamuso@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Two quite small fixes: one a build problem, and the other fixes
seccomp filters on x32."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix rebuild with EFI_STUB enabled
x86: remove the x32 syscall bitmask from syscall_get_nr()
Will Deacon [Sun, 7 Apr 2013 09:36:12 +0000 (21:36 +1200)]
alpha: irq: remove deprecated use of IRQF_DISABLED
Interrupt handlers are always invoked with interrupts disabled, so
remove all uses of the deprecated IRQF_DISABLED flag.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Reviewed-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Sun, 7 Apr 2013 09:36:11 +0000 (21:36 +1200)]
alpha: irq: run all handlers with interrupts disabled
Linux has expected that interrupt handlers are executed with local
interrupts disabled for a while now, so ensure that this is the case on
Alpha even for non-device interrupts such as IPIs.
Without this patch, secondary boot results in the following backtrace:
A similar dump occurs if you try to reboot using magic-sysrq.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Reviewed-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Will Deacon [Sun, 7 Apr 2013 09:36:10 +0000 (21:36 +1200)]
alpha: makefile: don't enforce small data model for kernel builds
Due to all of the goodness being packed into today's kernels, the
resulting image isn't as slim as it once was.
In light of this, don't pass -msmall-data to gcc, which otherwise results
in link failures due to impossible relocations when compiling anything but
the most trivial configurations.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Reviewed-by: Matt Turner <mattst88@gmail.com> Tested-by: Thorsten Kranzkowski <dl8bcu@dl8bcu.de> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Michael Cree <mcree@orcon.net.nz> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Honig [Fri, 29 Mar 2013 16:35:21 +0000 (09:35 -0700)]
KVM: Allow cross page reads and writes from cached translations.
This patch adds support for kvm_gfn_to_hva_cache_init functions for
reads and writes that will cross a page. If the range falls within
the same memslot, then this will be a fast operation. If the range
is split between two memslots, then the slower kvm_read_guest and
kvm_write_guest are used.
Tested: Test against kvm_clock unit tests.
Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Gleb Natapov <gleb@redhat.com>
Merge tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper fixes from Alasdair Kergon:
"A pair of patches to fix the writethrough mode of the device-mapper
cache target when the device being cached is not itself wrapped with
device-mapper."
* tag 'dm-3.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm cache: reduce bio front_pad size in writeback mode
dm cache: fix writes to cache device in writethrough mode
Merge tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"PCI updates for v3.9:
ASPM
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
kexec
PCI: Don't try to disable Bus Master on disconnected PCI devices
Platform ROM images
PCI: Add PCI ROM helper for platform-provided ROM images
nouveau: Attempt to use platform-provided ROM image
radeon: Attempt to use platform-provided ROM image
Hotplug
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI/PM: Disable runtime PM of PCIe ports
EISA
EISA/PCI: Fix bus res reference
EISA/PCI: Init EISA early, before PNP"
* tag 'pci-v3.9-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/PM: Disable runtime PM of PCIe ports
PCI/ACPI: Always resume devices on ACPI wakeup notifications
PCI: Don't try to disable Bus Master on disconnected PCI devices
Revert "PCI/ACPI: Request _OSC control before scanning PCI root bus"
radeon: Attempt to use platform-provided ROM image
nouveau: Attempt to use platform-provided ROM image
EISA/PCI: Init EISA early, before PNP
EISA/PCI: Fix bus res reference
PCI: Add PCI ROM helper for platform-provided ROM images
tty_port_tty_get might return a tty which is NULL. But it is
dereferenced unconditionally in edge_send. Stop dereferencing that by
sending usb_serial_port pointer around.
Merge tag 'usb-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.10 merge window
Here is the big Gadget & PHY pull request. Many of us have
been really busy lately getting multiple drivers to a better
position.
Since this pull request is so large, I will divide it in sections
so it's easier to grasp what's included.
- cleanups:
. UDC drivers no longer touch gadget->dev, that's now udc-core
responsibility
. Many more UDC drivers converted to usb_gadget_map/unmap_request()
. UDC drivers no longer initialize DMA-related fields from gadget's
device structure
. UDC drivers don't touch gadget.dev.driver directly
. UDC drivers don't assign gadget.dev.release directly
. Removal of some unused DMA_ADDR_INVALID
. Introduction of CONFIG_USB_PHY
. All phy drivers have been moved to drivers/usb/phy and renamed to
a common naming scheme
. Fix PHY layer so it never returns a NULL pointer, also fix all
callers to avoid using IS_ERR_OR_NULL()
. Sparse fixes all over the place
. drivers/usb/otg/ has been deleted
. Marvel drivers (mv_udc, ehci-mv, mv_otg and mv_u3d) improved clock
usage
- new features:
. UDC core now provides a generic way for tracking and reporting
UDC's state (not attached, resuming, suspended, addressed,
default, etc)
. twl4030-usb learned that it shouldn't be enabled during init
. Full DT support for DWC3 has been implemented
. ab8500-usb learned about pinctrl framework
. nop PHY learned about DeviceTree and regulators
. DWC3 learned about suspend/resume
. DWC3 can now be compiled in host-only and gadget-only (as well as
DRD) configurations
. UVC now enables streaming endpoint based on negotiated speed
. isp1301 now implements the PHY API properly
. configfs-based interface for gadget drivers which will lead to
the removal of all code which just combines functions together
to build functional gadget drivers.
. f_serial and f_obex were converted to new configfs interface while
maintaining old interface around.
- non-critical fixes:
. UVC gadget driver got fixes for Endpoint usage and stream calculation
. ab8500-usb fixed unbalanced clock and regulator API usage
. twl4030-usb got a fix for when OMAP3 is booted with cable connected
. fusb300_udc got a fix for DMA usage
. UVC got fixes for two assertions of the USB Video Class Compliance
specification revision 1.1
. build warning issues caused by recent addition of __must_check to
regulator API
These are all changes which deserve a mention, all other changes are related
to these one or minor spelling fixes and other similar tasks.
Dan Carpenter [Fri, 5 Apr 2013 05:42:41 +0000 (08:42 +0300)]
USB: keyspan: pull in one indent level
We can remove the "if (urb->actual_length) {" check because checking for
"while (i < urb->actual_length) {" is sufficient. This lets us pull the
code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In hardware_enqueue code adds one extra td with dma_pool_alloc if
mReq->req.zero is true. When _ep_nuke will be called for that endpoint,
dma_pool_free will not be called to free that memory again. That patch
fixes this.
Cc: stable <stable@vger.kernel.org> # v3.5 Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) Fix erroneous sock_orphan() leading to crashes and double
kfree_skb() in NFC protocol. From Thierry Escande and Samuel Ortiz.
2) Fix use after free in remain-on-channel mac80211 code, from Johannes
Berg.
3) nf_reset() needs to reset the NF tracing cookie, otherwise we can
leak it from one namespace into another. Fix from Gao Feng and
Patrick McHardy.
4) Fix overflow in channel scanning array of mwifiex driver, from Stone
Piao.
5) Fix loss of link after suspend/shutdown in r8169, from Hayes Wang.
6) Synchronization of unicast address lists to the undelying device
doesn't work because whether to sync is maintained as a boolean
rather than a true count. Fix from Vlad Yasevich.
7) Fix corruption of TSO packets in atl1e by limiting the segmented
packet length. From Hannes Frederic Sowa.
8) Revert bogus AF_UNIX credential passing change and fix the
coalescing issue properly, from Eric W Biederman.
9) Changes of ipv4 address lifetime settings needs to generate a
notification, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
netfilter: don't reset nf_trace in nf_reset()
net: ipv4: notify when address lifetime changes
ixgbe: fix registration order of driver and DCA nofitication
af_unix: If we don't care about credentials coallesce all messages
Revert "af_unix: dont send SCM_CREDENTIAL when dest socket is NULL"
bonding: remove sysfs before removing devices
atl1e: limit gso segment size to prevent generation of wrong ip length fields
net: count hw_addr syncs so that unsync works properly.
r8169: fix auto speed down issue
netfilter: ip6t_NPT: Fix translation for non-multiple of 32 prefix lengths
mwifiex: limit channel number not to overflow memory
NFC: microread: Fix build failure due to a new MEI bus API
iwlwifi: dvm: fix the passive-no-RX workaround
netfilter: nf_conntrack: fix error return code
NFC: llcp: Keep the connected socket parent pointer alive
mac80211: fix idle handling sequence
netfilter: nfnetlink_acct: return -EINVAL if object name is empty
netfilter: nfnetlink_queue: fix error return code in nfnetlink_queue_init()
netfilter: reset nf_trace in nf_reset
mac80211: fix remain-on-channel cancel crash
...
Jan Beulich [Wed, 3 Apr 2013 14:47:33 +0000 (15:47 +0100)]
x86: Fix rebuild with EFI_STUB enabled
eboot.o and efi_stub_$(BITS).o didn't get added to "targets", and hence
their .cmd files don't get included by the build machinery, leading to
the files always getting rebuilt.
Rather than adding the two files individually, take the opportunity and
add $(VMLINUX_OBJS) to "targets" instead, thus allowing the assignment
at the top of the file to be shrunk quite a bit.
At the same time, remove a pointless flags override line - the variable
assigned to was misspelled anyway, and the options added are
meaningless for assembly sources.
[ hpa: the patch is not minimal, but I am taking it for -urgent anyway
since the excess impact of the patch seems to be small enough. ]
usb: chipidea: udc: fix memory access of shared memory on armv5 machines
The udc uses an shared dma memory space between hard and software. This
memory layout is described in ci13xxx_qh and ci13xxx_td which are marked
with the attribute ((packed)).
The compiler currently does not know about the alignment of the memory
layout, and will create strb and ldrb operations.
The Datasheet of the synopsys core describes, that some operations on
the mapped memory need to be atomic double word operations. I.e. the
next pointer addressing in the qhead, as otherwise the hardware will
read wrong data and totally stuck.
This is also possible while working with the current active td queue,
and preparing the td->ptr.next in software while the hardware is still
working with the current active td which is supposed to be changed:
This appeares on armv5 machines where the hardware does not support
unaligned 32bit operations.
This patch adds the attribute ((aligned(4))) to the structures to tell
the compiler to use 32bit operations. It also adds an wmb() for the
prepared TD data before it gets enqueued into the qhead.
Cc: stable <stable@vger.kernel.org> # v3.5 Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patrick McHardy [Fri, 5 Apr 2013 18:42:05 +0000 (20:42 +0200)]
netfilter: don't reset nf_trace in nf_reset()
Commit 130549fe ("netfilter: reset nf_trace in nf_reset") added code
to reset nf_trace in nf_reset(). This is wrong and unnecessary.
nf_reset() is used in the following cases:
- when passing packets up the the socket layer, at which point we want to
release all netfilter references that might keep modules pinned while
the packet is queued. nf_trace doesn't matter anymore at this point.
- when encapsulating or decapsulating IPsec packets. We want to continue
tracing these packets after IPsec processing.
- when passing packets through virtual network devices. Only devices on
that encapsulate in IPv4/v6 matter since otherwise nf_trace is not
used anymore. Its not entirely clear whether those packets should
be traced after that, however we've always done that.
- when passing packets through virtual network devices that make the
packet cross network namespace boundaries. This is the only cases
where we clearly want to reset nf_trace and is also what the
original patch intended to fix.
Add a new function nf_reset_trace() and use it in dev_forward_skb() to
fix this properly.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus
Pull MIPS fixes from Ralf Baechle:
"Fixes for a number of small glitches in various corners of the MIPS
tree. No particular areas is standing out.
With this applied all MIPS defconfigs are building fine. No merge
conflicts are expected."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Delete definition of SA_RESTORER.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
MIPS: Fix build error cavium-octeon without CONFIG_SMP
MIPS: Kconfig: Rename SNIPROM too
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
MIPS: Unbreak function tracer for 64-bit kernel.
Pull GFS2 fixes from Steven Whitehouse:
"There are two patches which fix up a couple of minor issues in the DLM
interface code, a missing error path in gfs2_rs_alloc(), one patch
which fixes a problem during "withdraw" and a fix for discards/FITRIM
when using 4k sector sized devices."
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: Issue discards in 512b sectors
GFS2: Fix unlock of fcntl locks during withdrawn state
GFS2: return error if malloc failed in gfs2_rs_alloc()
GFS2: use memchr_inv
GFS2: use kmalloc for lvb bitmap
Merge tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of small driver fixes plus a fix for error handling in the
core - nothing too exciting overall."
* tag 'spi-fix-v3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/mpc512x-psc: optionally keep PSC SS asserted across xfer segmensts
spi: Unlock a spinlock before calling into the controller driver.
spi/s3c64xx: modified error interrupt handling and init
spi/bcm63xx: don't disable non enabled clocks in probe error path
spi/bcm63xx: Remove unused variable
spi: slink-tegra20: move runtime pm calls to transfer_one_message
Bob Peterson [Fri, 22 Mar 2013 14:07:24 +0000 (10:07 -0400)]
GFS2: Issue discards in 512b sectors
This patch changes GFS2's discard issuing code so that it calls
function sb_issue_discard rather than blkdev_issue_discard. The
code was calling blkdev_issue_discard and specifying the correct
sector offset and sector size, but blkdev_issue_discard expects
these values to be in terms of 512 byte sectors, even if the native
sector size for the device is different. Calling sb_issue_discard
with the BLOCK size instead ensures the correct block-to-512b-sector
translation. I verified that "minlen" is specified in blocks, so
comparing it to a number of blocks is correct.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch introduced a few races which cannot be easily fixed with a
small follow-up patch. Furthermore, the SoC with the broken hardware
register, which this patch intended to add support for, can only be used
with device trees, which this driver currently does not support.
[ Here is the discussion that led to this "revert" patch:
https://lkml.org/lkml/2013/4/3/176 ]
Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev fixes from Tomi Valkeinen:
"Fix uvesafb crash bug and typoed flag name in fbmon's new videomode
code"
* tag 'fbdev-fixes-3.9-rc6' of git://gitorious.org/linux-omap-dss2/linux:
video:uvesafb: Fix dereference NULL pointer code path
fbmon: use VESA_DMT_VSYNC_HIGH to fix typo
Merge tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains slightly more volumes than usual at this stage, mostly
because of my vacation in the last week. Nothing to scare, all small
and/or trivial fixes:
- Fix loop path handling in ASoC DAPM
- Some memory handling fixes in ASoC core
- Fix spear_pcm to adapt to the updated API
- HD-audio HDMI ELD handling fixes
- Fix for CM6331 USB-audio SRC change bugs
- Revert power_save_controller option change due to user-space usage
- A few other small ASoC and HD-audio fixes"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/generic - fix uninitialized variable
Revert "ALSA: hda - Allow power_save_controller option override DCAPS"
ALSA: hda - fix typo in proc output
ALSA: hda - Enabling Realtek ALC 671 codec
ALSA: usb: Work around CM6631 sample rate change bug
ALSA: hda - bug fix on HDMI ELD debug message
ALSA: hda - bug fix on return value when getting HDMI ELD info
ASoC: dma-sh7760: Fix compile error
ASoC: core: fix invalid free of devm_ allocated data
ASoC: spear_pcm: Update to new pcm_new() API
ASoC:: max98090: Remove executable bit
ASoC: dapm: Fix pointer dereference in is_connected_output_ep()
ASoC: pcm030 audio fabric: remove __init from probe
ASoC: imx-ssi: Fix occasional AC97 reset failure
ASoC: core: fix possible memory leak in snd_soc_bytes_put()
ASoC: wm_adsp: fix possible memory leak in wm_adsp_load_coeff()
ASoC: dapm: Fix handling of loops
ASoC: si476x: Add missing break for SNDRV_PCM_FORMAT_S8 switch case
Mike Snitzer [Fri, 5 Apr 2013 14:36:34 +0000 (15:36 +0100)]
dm cache: reduce bio front_pad size in writeback mode
A recent patch to fix the dm cache target's writethrough mode extended
the bio's front_pad to include a 1056-byte struct dm_bio_details.
Writeback mode doesn't need this, so this patch reduces the
per_bio_data_size to 16 bytes in this case instead of 1096.
The dm_bio_details structure was added in "dm cache: fix writes to
cache device in writethrough mode" which fixed commit e2e74d617e ("dm
cache: fix race in writethrough implementation"). In writeback mode
we avoid allocating the writethrough-specific members of the
per_bio_data structure (the dm_bio_details structure included).
Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Darrick J. Wong [Fri, 5 Apr 2013 14:36:32 +0000 (15:36 +0100)]
dm cache: fix writes to cache device in writethrough mode
The dm-cache writethrough strategy introduced by commit e2e74d617eadc15
("dm cache: fix race in writethrough implementation") issues a bio to
the origin device, remaps and then issues the bio to the cache device.
This more conservative in-series approach was selected to favor
correctness over performance (of the previous parallel writethrough).
However, this in-series implementation that reuses the same bio to write
both the origin and cache device didn't take into account that the block
layer's req_bio_endio() modifies a completing bio's bi_sector and
bi_size. So the new writethrough strategy needs to preserve these bio
fields, and restore them before submission to the cache device,
otherwise nothing gets written to the cache (because bi_size is 0).
This patch adds a struct dm_bio_details field to struct per_bio_data,
and uses dm_bio_record() and dm_bio_restore() to ensure the bio is
restored before reissuing to the cache device. Adding such a large
structure to the per_bio_data is not ideal but we can improve this
later, for now correctness is the important thing.
This problem initially went unnoticed because the dm-cache test-suite
uses a linear DM device for the dm-cache device's origin device.
Writethrough worked as expected because DM submits a *clone* of the
original bio, so the original bio which was reused for the cache was
never touched.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Ralf Baechle [Mon, 25 Mar 2013 12:43:14 +0000 (13:43 +0100)]
MIPS: Delete definition of SA_RESTORER.
SA_RESTORER used to be defined as 0x04000000 but only the O32 ABI ever
supported its use and no libc was using it, so the entire sa-restorer
functionality was removed with lmo commit 39bffc12c3580ab [Zap sa_restorer.]
for 2.5.48 retaining only the SA_RESTORER definition as a reminder to avoid
accidental reuse of the mask bit.
Upstream cdef9602fbf1871a43f0f1b5cea10dd0f275167d [signal: always clear
sa_restorer on execve] adds code that assumes sa_sigaction has an
sa_restorer field, if SA_RESTORER is defined which would break MIPS.
So remove the SA_RESTORER definition before the v3.8.4 merge.
MIPS: Fix ISA level which causes secondary cache init bypassing and more
The commit a96102be70 introduced set_isa() where compatible ISA info is
also set aside from the one gets passed in. It means, for example, 1004K
will have MIPS_CPU_ISA_M32R2/M32R1/II/I flags. This leads to things like
the following inappropriate:
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: linux-mips@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Bolle [Thu, 4 Apr 2013 12:47:01 +0000 (12:47 +0000)]
MIPS: Alchemy: Fix typo "CONFIG_DEBUG_PCI"
Commit 7517de348663b08a808aff44b5300e817157a568 ("MIPS: Alchemy: Redo
PCI as platform driver") added a reference to CONFIG_DEBUG_PCI. Change
it to CONFIG_PCI_DEBUG, as that is a valid Kconfig macro.
Also add a newline to a debugging printk that this fix enables.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Daney [Tue, 2 Apr 2013 22:59:29 +0000 (22:59 +0000)]
MIPS: Unbreak function tracer for 64-bit kernel.
Commit 58b69401c797 [MIPS: Function tracer: Fix broken function tracing]
completely broke the function tracer for 64-bit kernels. The symptom is
a system hang very early in the boot process.
The fix: Remove/fix $sp adjustments for 64-bit case.
Signed-off-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Cc: Al Cooper <alcooperx@gmail.com> Cc: viric@viric.name Cc: stable@vger.kernel.org # 3.8.x Signed-off-by: Ralf Baechle <ralf@linux-mips.org>