Jakub Kicinski [Tue, 4 Jul 2017 09:27:21 +0000 (02:27 -0700)]
nfp: default to chained metadata prepend format
ABI 4.x introduced the chained metadata format and made it the
only one possible. There are cases, however, where the old
format is preferred - mostly to make interoperation with VFs
using ABI 3.x easier for the datapath. In ABI 5.x we allowed
for more flexibility by selecting the metadata format based
on capabilities. The default was left to non-chained.
In case of fallback traffic, there is no capability telling the
driver there may be chained metadata. With a very stripped-
-down FW the default old metadata format would be selected
making the driver drop all fallback traffic.
This patch changes the default selection in the driver. It
should not hurt with old firmwares, because if they don't
advertise RSS they will not produce metadata anyway. New
firmwares advertising ABI 5.x, however, can depend on the
driver defaulting to chained format.
Fixes: f9380629fafc ("nfp: advertise support for NFD ABI 0.5") Suggested-by: Michael Rapson <michael.rapson@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 4 Jul 2017 09:27:20 +0000 (02:27 -0700)]
nfp: remove legacy MAC address lookup
The legacy MAC address lookup doesn't work well with breakout
cables. We are probably better off picking random addresses
than the wrong ones in the theoretical scenario where management
FW didn't tell us what the port config is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 4 Jul 2017 09:27:19 +0000 (02:27 -0700)]
nfp: improve order of interfaces in breakout mode
For historical reasons we enumerate the vNICs in order. This means
that if user configures breakout on a multiport card, the first
interface of the second port will have its MAC address changed.
What's worse, when moved from static information (HWInfo) to using
management FW (NSP), more features started depending on the port ids.
Right now in case of breakout first subport of the second port and
second subport of the first port will have their link info swapped.
Revise the ordering scheme so that first subport maintains its address.
Side effect of this change is that we will use base lane ids in
devlink (i.e. 40G ports will be 4 ids apart), e.g.:
pci/0000:04:00.0/0: type eth netdev p6p1
pci/0000:04:00.0/4: type eth netdev p6p2
Note that behaviour of phys_port_id is not changed since there is
a separate id number for the subport there.
Fixes: ec8b1fbe682d ("nfp: support port splitting via devlink") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 4 Jul 2017 15:09:59 +0000 (16:09 +0100)]
net: macb: remove extraneous return when MACB_EXT_DESC is defined
When macro MACB_EXT_DESC is defined we end up with two identical
return statements and just one is sufficient. Remove the extra
return.
Detected by CoverityScan, CID#1449361 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Tue, 4 Jul 2017 15:21:12 +0000 (16:21 +0100)]
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
There appears to be a missing break in the TCP_BPF_SNDCWND_CLAMP case.
Currently the non-error path where val is greater than zero falls through
to the default case that sets the error return to -EINVAL. Add in
the missing break.
Detected by CoverityScan, CID#1449376 ("Missing break in switch")
Fixes: 13bf96411ad2 ("bpf: Adds support for setting sndcwnd clamp") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Lawrence Brakmo [Tue, 4 Jul 2017 22:57:50 +0000 (15:57 -0700)]
bpf: fix return in load_bpf_file
The function load_bpf_file ignores the return value of
load_and_attach(), so even if load_and_attach() returns an error,
load_bpf_file() will return 0.
Now, load_bpf_file() can call load_and_attach() multiple times and some
can succeed and some could fail. I think the correct behavor is to
return error on the first failed load_and_attach().
v2: Added missing SOB
Signed-off-by: Lawrence Brakmo <brakmo@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
fix rtm policy name typo in mpls_getroute and also remove
export of rtm_ipv4_policy
Fixes: 397fc9e5cefe ("mpls: route get support") Reported-by: David S. Miller <davem@davemloft.net> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
====================
v2 net subsystem misc refcounter conversions
Changes in v2:
* rebase on top of net-next
* currently by default refcount_t = atomic_t (*) and uses all
atomic standard operations unless CONFIG_REFCOUNT_FULL is enabled.
This is a compromise for the systems that are critical on
performance (such as net) and cannot accept even slight delay
on the refcounter operations.
This series, for various misc network components, replaces atomic_t reference
counters with the new refcount_t type and API (see include/linux/refcount.h).
By doing this we prevent intentional or accidental
underflows or overflows that can led to use-after-free vulnerabilities.
These are the last networking-related conversions with the exception of
network drivers (to be send separately).
Please excuse the long patch set, but seems like breaking it up
won't save that much on CC list and most of the changes are
trivial.
The patches are fully independent and can be cherry-picked separately.
In order to try with refcount functionality enabled in run-time,
CONFIG_REFCOUNT_FULL must be enabled.
NOTE: automatic kernel builder for some reason doesn't like all my
network branches and regularly times out the builds on these branches.
Suggestion for "waiting a day for a good coverage" doesn't work, as
we have seen with generic network conversions. So please wait for the
full report from kernel test rebot before merging further up.
This has been compile-tested in 116 configs, but 71 timed out (including
all s390-related configs again). I am trying to see if they can fix
build coverage for me in meanwhile.
* The respective change is currently merged into -next as
"locking/refcount: Create unchecked atomic_t implementation".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, xfrm: convert sec_path.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, xfrm: convert xfrm_policy.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, xfrm: convert xfrm_state.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, x25: convert x25_neigh.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, x25: convert x25_route.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, rds: convert rds_message.m_refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, rds: convert rds_mr.r_refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, rds: convert rds_incoming.i_refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, rds: convert rds_ib_device.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sunrpc: convert gss_upcall_msg.count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sunrpc: convert gss_cl_ctx.count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, netrom: convert nr_node.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, netrom: convert nr_neigh.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipx: convert ipx_route.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipx: convert ipx_interface.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, lapb: convert lapb_cb.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, sched: convert Qdisc.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, calipso: convert calipso_doi.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, bridge: convert net_bridge_vlan.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, atm: convert eg_cache_entry.use from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, atm: convert in_cache_entry.use from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, atm: convert lec_arp_table.usage from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, atm: convert atm_dev.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, decnet: convert dn_fib_info.fib_clntref from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, vxlan: convert vxlan_sock.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, l2tp: convert l2tp_session.ref_count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, l2tp: convert l2tp_tunnel.ref_count from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, llc: convert llc_sap.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RTM_GETROUTE doit handler for mpls routes.
Input:
RTA_DST - input label
RTA_NEWDST - labels in packet for multipath selection
By default the getroute handler returns matched
nexthop label, via and oif
With RTM_F_FIB_MATCH flag, full matched route is
returned.
example (with patched iproute2):
$ip -f mpls route show
101
nexthop as to 102/103 via inet 172.16.2.2 dev virt1-2
nexthop as to 302/303 via inet 172.16.12.2 dev virt1-12
201
nexthop as to 202/203 via inet6 2001:db8:2::2 dev virt1-2
nexthop as to 402/403 via inet6 2001:db8:12::2 dev virt1-12
$ip -f mpls route get 103
RTNETLINK answers: Network is unreachable
$ip -f mpls route get 101
101 as to 102/103 via inet 172.16.2.2 dev virt1-2
$ip -f mpls route get as to 302/303 101
101 as to 302/303 via inet 172.16.12.2 dev virt1-12
$ip -f mpls route get fibmatch 103
RTNETLINK answers: Network is unreachable
$ip -f mpls route get fibmatch 101
101
nexthop as to 102/103 via inet 172.16.2.2 dev virt1-2
nexthop as to 302/303 via inet 172.16.12.2 dev virt1-12
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
current code silently ignores change of port in the request
message. This patch makes sure the port is modified and
notification is sent to userspace.
Fixes: cf6b8e1eedff ("bridge: add API to notify bridge driver of learned FBD on offloaded device") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
SYN-ACK responses on a server in response to a SYN from a client
did not get the injected skb mark that was tagged on the SYN packet.
Fixes: 84f39b08d786 ("net: support marking accepting TCP sockets") Reviewed-by: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Changes in v2:
* rebase on top of net-next
* currently by default refcount_t = atomic_t (*) and uses all
atomic standard operations unless CONFIG_REFCOUNT_FULL is enabled.
This is a compromise for the systems that are critical on
performance (such as net) and cannot accept even slight delay
on the refcounter operations.
This series, for ipv4/ipv6 network components, replaces atomic_t reference
counters with the new refcount_t type and API (see include/linux/refcount.h).
By doing this we prevent intentional or accidental
underflows or overflows that can led to use-after-free vulnerabilities.
The patches are fully independent and can be cherry-picked separately.
In order to try with refcount functionality enabled in run-time,
CONFIG_REFCOUNT_FULL must be enabled.
NOTE: automatic kernel builder for some reason doesn't like all my
network branches and regularly times out the builds on these branches.
Suggestion for "waiting a day for a good coverage" doesn't work, as
we have seen with generic network conversions. So please wait for the
full report from kernel test rebot before merging further up.
This has been compile-tested in 116 configs, but 71 timed out (including
all s390-related configs again). I am trying to see if they can fix
build coverage for me in meanwhile.
* The respective change is currently merged into -next as
"locking/refcount: Create unchecked atomic_t implementation".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv4: convert fib_info.fib_clntref from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv4: convert cipso_v4_doi.refcount from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert ip6addrlbl_entry.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert xfrm6_tunnel_spi.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert ifacaddr6.aca_refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert ifmcaddr6.mca_refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert inet6_ifaddr.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert inet6_dev.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net, ipv6: convert ipv6_txoptions.refcnt from atomic_t to refcount_t
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 3 Jul 2017 18:55:25 +0000 (21:55 +0300)]
qed: initialize ll2_syn_handle at start of function
Fix compilation warning
qed_iwarp.c:1721:5: warning: ll2_syn_handle may be used
uninitialized in this function
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Axtens [Mon, 3 Jul 2017 11:46:43 +0000 (21:46 +1000)]
openvswitch: fix mis-ordered comment lines for ovs_skb_cb
I was trying to wrap my head around meaning of mru, and realised
that the second line of the comment defining it had somehow
ended up after the line defining cutlen, leading to much confusion.
Reorder the lines to make sense.
Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Jul 2017 12:51:45 +0000 (05:51 -0700)]
Merge tag 'wireless-drivers-next-for-davem-2017-07-03' of https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.13
Last minute changes to get new hardware and firmware support for
iwlwifi and few other changes I was able to squeeze in. Also two
patches for ieee80211.h and nl80211 as Johannes is away.
Major changes:
iwlwifi
* some important fixes for 9000 HW
* support for version 30 of the FW API for 8000 and 9000 series
* a few new PCI IDs for 9000 series
* reorganization of common files
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK and 802.1X
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 717d1e993ad8 ("net: convert fib_rule.refcnt from atomic_t to refcount_t") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The variable mlx4_log_num_mgm_entry_size is only called in main.c.
CC: Joe Jin <joe.jin@oracle.com> CC: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix memory corruption introduced with the support of both IPv4 and IPv6
sockets in a single device. The same bug is present in VXLAN and Geneve.
====================
Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.
Fixes: 8ed66f0e8235 ("geneve: implement support for IPv6-based tunnels") Cc: John W. Linville <linville@tuxdriver.com> Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.
Fixes: b1be00a6c39f ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device") Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Sun, 2 Jul 2017 15:57:28 +0000 (18:57 +0300)]
net/mlxfw: Properly handle dependancy with non-loadable mlx5
If mlx5 is set to be built-in and mlxfw as a module, we
get a link error:
drivers/built-in.o: In function `mlx5_firmware_flash':
(.text+0x5aed72): undefined reference to `mlxfw_firmware_flash'
Since we don't want to mandate selecting mlxfw for mlx5 users, we
use the IS_REACHABLE macro to make sure that a stub is exposed
to the caller.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reported-by: Jakub Kicinski <kubakici@wp.pl> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Miscellanous improvements I still had in my queue, it adds a new
bpf_skb_adjust_room() helper for cls_bpf, exports to fdinfo whether
tail call array owner is JITed, so iproute2 error reporting can be
improved on that regard, a small cleanup and extension to trace
printk, two verifier patches, one to make the code around narrower
ctx access a bit more straight forward and one to allow for imm += x
operations, that we've seen LLVM generating and the verifier currently
rejecting. We've included the patch 6 given it's rather small and
we ran into it from LLVM side, it would be great if it could be
queued for stable as well after the merge window. Last but not least,
test cases are added also related to imm alu improvement.
Thanks a lot!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 2 Jul 2017 00:13:31 +0000 (02:13 +0200)]
bpf: add various test cases for verifier selftest
Add couple of verifier test cases for x|imm += pkt_ptr, including the
imm += x extension.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Sun, 2 Jul 2017 00:13:30 +0000 (02:13 +0200)]
bpf, verifier: add additional patterns to evaluate_reg_imm_alu
Currently the verifier does not track imm across alu operations when
the source register is of unknown type. This adds additional pattern
matching to catch this and track imm. We've seen LLVM generating this
pattern while working on cilium.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Sun, 2 Jul 2017 00:13:29 +0000 (02:13 +0200)]
bpf: extend bpf_trace_printk to support %i
Currently, bpf_trace_printk does not support common formatting
symbol '%i' however vsprintf does and is what eventually gets
called by bpf helper. If users are used to '%i' and currently
make use of it, then bpf_trace_printk will just return with
error without dumping anything to the trace pipe, so just add
support for '%i' to the helper.
Signed-off-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 2 Jul 2017 00:13:28 +0000 (02:13 +0200)]
bpf: export whether tail call has jited owner
We do export through fdinfo already whether a prog is JITed or not,
given a program load can fail in case of either prog or tail call map
has JITed property, but neither both are JITed or not JITed, we can
facilitate error reporting in loaders like iproute2 through exporting
owner_jited of tail call map. We already do export owner_prog_type
through this facility, so parser can pick up both for comparison.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 2 Jul 2017 00:13:27 +0000 (02:13 +0200)]
bpf: simplify narrower ctx access
This work tries to make the semantics and code around the
narrower ctx access a bit easier to follow. Right now
everything is done inside the .is_valid_access(). Offset
matching is done differently for read/write types, meaning
writes don't support narrower access and thus matching only
on offsetof(struct foo, bar) is enough whereas for read
case that supports narrower access we must check for
offsetof(struct foo, bar) + offsetof(struct foo, bar) +
sizeof(<bar>) - 1 for each of the cases. For read cases of
individual members that don't support narrower access (like
packet pointers or skb->cb[] case which has its own narrow
access logic), we check as usual only offsetof(struct foo,
bar) like in write case. Then, for the case where narrower
access is allowed, we also need to set the aux info for the
access. Meaning, ctx_field_size and converted_op_size have
to be set. First is the original field size e.g. sizeof(<bar>)
as in above example from the user facing ctx, and latter
one is the target size after actual rewrite happened, thus
for the kernel facing ctx. Also here we need the range match
and we need to keep track changing convert_ctx_access() and
converted_op_size from is_valid_access() as both are not at
the same location.
We can simplify the code a bit: check_ctx_access() becomes
simpler in that we only store ctx_field_size as a meta data
and later in convert_ctx_accesses() we fetch the target_size
right from the location where we do convert. Should the verifier
be misconfigured we do reject for BPF_WRITE cases or target_size
that are not provided. For the subsystems, we always work on
ranges in is_valid_access() and add small helpers for ranges
and narrow access, convert_ctx_accesses() sets target_size
for the relevant instruction.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Cc: Yonghong Song <yhs@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 2 Jul 2017 00:13:26 +0000 (02:13 +0200)]
bpf: add bpf_skb_adjust_room helper
This work adds a helper that can be used to adjust net room of an
skb. The helper is generic and can be further extended in future.
Main use case is for having a programmatic way to add/remove room to
v4/v6 header options along with cls_bpf on egress and ingress hook
of the data path. It reuses most of the infrastructure that we added
for the bpf_skb_change_type() helper which can be used in nat64
translations. Similarly, the helper only takes care of adjusting the
room so that related data is populated and csum adapted out of the
BPF program using it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Sun, 2 Jul 2017 00:13:25 +0000 (02:13 +0200)]
bpf, net: add skb_mac_header_len helper
Add a small skb_mac_header_len() helper similarly as the
skb_network_header_len() we have and replace open coded
places in BPF's bpf_skb_change_proto() helper. Will also
be used in upcoming work.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Tore Anderson [Sat, 1 Jul 2017 13:20:02 +0000 (15:20 +0200)]
net: cdc_mbim: apply "NDP to end" quirk to HP lt4132
The HP lt4132 LTE/HSPA+ 4G Module (03f0:a31d) is a rebranded Huawei
ME906s-158 device. It, like the ME906s-158, requires the "NDP to end"
quirk for correct operation.
Signed-off-by: Tore Anderson <tore@fud.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Matteo Croce [Fri, 30 Jun 2017 16:21:47 +0000 (18:21 +0200)]
Documentation: fix wrong example command
In the IPVLAN documentation there is an example command line where the
master and slave interface names are inverted.
Fix the command line and also add the optional `name' keyword to better
describe what the command is doing.
v2: added commit message
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Fri, 30 Jun 2017 13:50:00 +0000 (15:50 +0200)]
vxlan: correctly set vxlan->net when creating the device in a netns
Commit a985343ba906 ("vxlan: refactor verification and application of
configuration") modified vxlan device creation, and replaced the
assignment of vxlan->net to src_net with dev_net(netdev) in ->setup().
But dev_net(netdev) is not the same as src_net. At the time ->setup()
is called, dev_net hasn't been set yet, so we end up creating the
socket for the vxlan device in init_net.
Fix this by bringing back the assignment of vxlan->net during device
creation.
Fixes: a985343ba906 ("vxlan: refactor verification and application of configuration") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Jul 2017 09:01:16 +0000 (02:01 -0700)]
Merge branch 'hns-phy-loopback'
Lin Yun Sheng says:
====================
Add loopback support in phy_driver and hns ethtool fix
This Patch Set add set_loopback in phy_driver and use it to setup loopback
when doing ethtool phy self_test.
Patch V8:
Respin the Patch based on net-next
Patch V7:
1. Add comment why resume the phy in hns_nic_config_phy_loopback.
2. Fix a typo error in patch description.
Patch V6:
Fix Or'ing error code in __lb_setup.
Patch V5:
Removing non loopback related code change.
Patch V4:
1. Remove c45 checking
2. Add -ENOTSUPP when function pointer is null,
take mutex in phy_loopback.
Patch V3:
Calling phy_loopback enable and disable in pair in hns mac driver.
Patch V2:
1. Add phy_loopback in phy_device.c.
2. Do error checking and do the read and write once in
genphy_loopback.
3. Remove gen10g_loopback in phy_device.c.
Patch V1:
Initial Submit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Yun Sheng [Fri, 30 Jun 2017 09:44:15 +0000 (17:44 +0800)]
net: phy: Add phy loopback support in net phy framework
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca [Thu, 29 Jun 2017 14:56:54 +0000 (16:56 +0200)]
ipv6: dad: don't remove dynamic addresses if link is down
Currently, when the link for $DEV is down, this command succeeds but the
address is removed immediately by DAD (1):
ip addr add 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
In the same situation, this will succeed and not remove the address (2):
ip addr add 1111::12/64 dev $DEV
ip addr change 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
The comment in addrconf_dad_begin() when !IF_READY makes it look like
this is the intended behavior, but doesn't explain why:
* If the device is not ready:
* - keep it tentative if it is a permanent address.
* - otherwise, kill it.
We clearly cannot prevent userspace from doing (2), but we can make (1)
work consistently with (2).
addrconf_dad_stop() is only called in two cases: if DAD failed, or to
skip DAD when the link is down. In that second case, the fix is to avoid
deleting the address, like we already do for permanent addresses.
Fixes: 3c21edbd1137 ("[IPV6]: Defer IPv6 device initialization until the link becomes ready.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Jim Baxter [Wed, 28 Jun 2017 20:35:29 +0000 (21:35 +0100)]
net: cdc_ncm: Reduce memory use when kernel memory low
The CDC-NCM driver can require large amounts of memory to create
skb's and this can be a problem when the memory becomes fragmented.
This especially affects embedded systems that have constrained
resources but wish to maximise the throughput of CDC-NCM with 16KiB
NTB's.
The issue is after running for a while the kernel memory can become
fragmented and it needs compacting.
If the NTB allocation is needed before the memory has been compacted
the atomic allocation can fail which can cause increased latency,
large re-transmissions or disconnections depending upon the data
being transmitted at the time.
This situation occurs for less than a second until the kernel has
compacted the memory but the failed devices can take a lot longer to
recover from the failed TX packets.
To ease this temporary situation I modified the CDC-NCM TX path to
temporarily switch into a reduced memory mode which allocates an NTB
that will fit into a USB_CDC_NCM_NTB_MIN_OUT_SIZE (default 2048 Bytes)
sized memory block and only transmit NTB's with a single network frame
until the memory situation is resolved.
Each time this issue occurs we wait for an increasing number of
reduced size allocations before requesting a full size one to not
put additional pressure on a low memory system.
Once the memory is compacted the CDC-NCM data can resume transmitting
at the normal tx_max rate once again.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com> Reviewed-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Jul 2017 08:43:46 +0000 (01:43 -0700)]
Merge branch 'qed-Add-iWARP-support-for-QL4xxxx'
Michal Kalderon says:
====================
qed: Add iWARP support for QL4xxxx
This patch series adds iWARP support to our QL4xxxx networking adapters.
The code changes span across qed and qedr drivers, but this series contains
changes to qed only. Once the series is accepted, the qedr series will
be submitted to the rdma tree.
There is one additional qed patch which enables the iWARP, this patch is
delayed until the qedr series will be accepted.
The patches were previously sent as an RFC, and these are the first 12
patches in the RFC series:
https://www.spinics.net/lists/linux-rdma/msg51416.html
This series was tested and built against net-next.
MAINTAINERS file is not updated in this PATCH as there is a pending patch
for qedr driver update https://patchwork.kernel.org/patch/9752761.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add iWARP support for physical queue allocation
iWARP has different physical queue requirements than RoCE
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: Add iWARP protocol support in context allocation
When computing how much memory is required for the different hw clients
iWARP protocol should be taken into account
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: iWARP CM add listener functions and initial SYN processing
This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
qed: iWARP CM - setup a ll2 connection for handling SYN packets
iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>