Rob Herring [Thu, 13 Sep 2018 18:12:29 +0000 (13:12 -0500)]
ARM: dts: imx: Fix SPI bus warnings
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Li Yang <leoyang.li@nxp.com> Cc: Stefan Agner <stefan@agner.ch> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM: dts: imx6ull: update vdd_soc voltage for 900MHz operating point
Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Oleksij Rempel [Thu, 2 Aug 2018 10:34:25 +0000 (12:34 +0200)]
ARM: dts: imx6: RIoTboard provide standby on power off option
This board, as well as some other boards with i.MX6 and a PMIC, uses a
"PMIC_STBY_REQ" line to notify the PMIC about a state change.
The PMIC is programmed for a specific state change before triggering the
line.
In this case, PMIC_STBY_REQ can be used for stand by, sleep
and power off modes.
Stefan Agner [Thu, 6 Sep 2018 23:46:58 +0000 (16:46 -0700)]
ARM: dts: imx6q-apalis: mux RESET_MOCI# signal
The pinctrl properties on the IOMUXC node get overwritten by the
carrier board level device tree, hence the pinctrl_reset_moci
pinctrl does not get applied.
Associate the pinctrl_reset_moci pinctrl with the PCIe node where
we also make use of the pin as a reset GPIO.
Since the pin is muxed as a GPIO by default not muxing it explicitly
worked fine in practise.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Russell King [Sun, 2 Sep 2018 16:29:12 +0000 (18:29 +0200)]
ARM: dts: vf610-zii-dev-rev-c: add support for one SFF module
The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM: dts: imx6ull: keep IMX6UL_ prefix for signals on both i.MX6UL and i.MX6ULL
Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:
Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Tuomas Tynkkynen [Mon, 20 Aug 2018 21:07:18 +0000 (00:07 +0300)]
ARM: dts: imx6qdl-wandboard: Add stdout-path
Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.
The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).
Jacopo Mondi [Tue, 14 Aug 2018 13:21:46 +0000 (15:21 +0200)]
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6
The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Jacopo Mondi [Tue, 14 Aug 2018 13:21:45 +0000 (15:21 +0200)]
ARM: dts: imx6qdl: Add Engicam i.Core 1.5 MX6
The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.
The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
Jagan Teki [Tue, 7 Aug 2018 07:08:37 +0000 (12:38 +0530)]
ARM: dts: imx6ul-isiot: Move node definitions into dtsi
Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"First batch of fixes post-merge window:
- A handful of devicetree changes for i.MX2{3,8} to change over to
new panel bindings. The platforms were moved from legacy
framebuffers to DRM and some development board panels hadn't yet
been converted.
- OMAP fixes related to ti-sysc driver conversion fallout, fixing
some register offsets, no_console_suspend fixes, etc.
- Droid4 changes to fix flaky eMMC probing and vibrator DTS mismerge.
- Fixed 0755->0644 permissions on a newly added file.
- Defconfig changes to make ARM Versatile more useful with QEMU
(helps testing).
- Enable defconfig options for new TI SoC platform that was merged
this window (AM6)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: defconfig: Enable TI's AM6 SoC platform
ARM: defconfig: Update the ARM Versatile defconfig
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
ARM: imx_v6_v7_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: mxs_defconfig: Select CONFIG_DRM_PANEL_SEIKO_43WVF1G
ARM: dts: imx23-evk: Convert to the new display bindings
ARM: dts: imx23-evk: Move regulators outside simple-bus
ARM: dts: imx28-evk: Convert to the new display bindings
ARM: dts: imx28-evk: Move regulators outside simple-bus
Revert "ARM: dts: imx7d: Invert legacy PCI irq mapping"
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Merge branch 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"Speculation:
- Make the microcode check more robust
- Make the L1TF memory limit depend on the internal cache physical
address space and not on the CPUID advertised physical address
space, which might be significantly smaller. This avoids disabling
L1TF on machines which utilize the full physical address space.
- Fix the GDT mapping for EFI calls on 32bit PTI
- Fix the MCE nospec implementation to prevent #GP
Fixes and robustness:
- Use the proper operand order for LSL in the VDSO
- Prevent NMI uaccess race against CR3 switching
- Add a lockdep check to verify that text_mutex is held in
text_poke() functions
- Repair the fallout of giving native_restore_fl() a prototype
- Prevent kernel memory dumps based on usermode RIP
- Wipe KASAN shadow stack before rewinding the stack to prevent false
positives
- Move the AMS GOTO enforcement to the actual build stage to allow
user API header extraction without a compiler
- Fix a section mismatch introduced by the on demand VDSO mapping
change
Miscellaneous:
- Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Fix section mismatch warning/error
x86/vdso: Fix lsl operand order
x86/mce: Fix set_mce_nospec() to avoid #GP fault
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
x86/nmi: Fix NMI uaccess race against CR3 switching
x86: Allow generating user-space headers without a compiler
x86/dumpstack: Don't dump kernel memory based on usermode RIP
x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
x86/irqflags: Mark native_restore_fl extern inline
x86/build: Remove jump label quirk for GCC older than 4.5.2
x86/Kconfig: Fix trivial typo
x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
x86/spectre: Add missing family 6 check to microcode check
Merge branch 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"A small set of updates for core code:
- Prevent tracing in functions which are called from trace patching
via stop_machine() to prevent executing half patched function trace
entries.
- Remove old GCC workarounds
- Remove pointless includes of notifier.h"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Remove workaround for unreachable warnings from old GCC
notifier: Remove notifier header file wherever not used
watchdog: Mark watchdog touch functions as notrace
Randy Dunlap [Sun, 2 Sep 2018 04:01:28 +0000 (21:01 -0700)]
x86/pti: Fix section mismatch warning/error
Fix the section mismatch warning in arch/x86/mm/pti.c:
WARNING: vmlinux.o(.text+0x6972a): Section mismatch in reference from the function pti_clone_pgtable() to the function .init.text:pti_user_pagetable_walk_pte()
The function pti_clone_pgtable() references
the function __init pti_user_pagetable_walk_pte().
This is often because pti_clone_pgtable lacks a __init
annotation or the annotation of pti_user_pagetable_walk_pte is wrong.
FATAL: modpost: Section mismatches detected.
Fixes: 85900ea51577 ("x86/pti: Map the vsyscall page if needed") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andy Lutomirski <luto@kernel.org> Link: https://lkml.kernel.org/r/43a6d6a3-d69d-5eda-da09-0b1c88215a2a@infradead.org
Olof Johansson [Sun, 2 Sep 2018 01:22:19 +0000 (18:22 -0700)]
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Samuel Neves [Sat, 1 Sep 2018 20:14:52 +0000 (21:14 +0100)]
x86/vdso: Fix lsl operand order
In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.
Fixes: a582c540ac1b ("x86/vdso: Use RDPID in preference to LSL when available") Signed-off-by: Samuel Neves <sneves@dei.uc.pt> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Two small fixes, one for the x86 Stoney SoC to get a more accurate clk
frequency and the other to fix a bad allocation in the Nuvoton NPCM7XX
driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: x86: Set default parent to 48Mhz
clk: npcm7xx: fix memory allocation
LuckTony [Fri, 31 Aug 2018 16:55:06 +0000 (09:55 -0700)]
x86/mce: Fix set_mce_nospec() to avoid #GP fault
The trick with flipping bit 63 to avoid loading the address of the 1:1
mapping of the poisoned page while the 1:1 map is updated used to work when
unmapping the page. But it falls down horribly when attempting to directly
set the page as uncacheable.
The problem is that when the cache mode is changed to uncachable, the pages
needs to be flushed from the cache first. But the decoy address is
non-canonical due to bit 63 flipped, and the CLFLUSH instruction throws a
#GP fault.
Add code to change_page_attr_set_clr() to fix the address before calling
flush.
Fixes: 284ce4011ba6 ("x86/memory_failure: Introduce {set, clear}_mce_nospec()") Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Anvin <hpa@zytor.com> Cc: Borislav Petkov <bp@alien8.de> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Dave Jiang <dave.jiang@intel.com> Link: https://lkml.kernel.org/r/20180831165506.GA9605@agluck-desk
Linus Torvalds [Fri, 31 Aug 2018 16:20:30 +0000 (09:20 -0700)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"A few arm64 fixes came in this week, specifically fixing some nasty
truncation of return values from firmware calls and resolving a
VM_BUG_ON due to accessing uninitialised struct pages corresponding to
NOMAP pages.
Summary:
- Fix typos in SVE documentation
- Fix type-checking and implicit truncation for SMCCC calls
- Force CONFIG_HOLES_IN_ZONE=y so that SLAB doesn't fall over NOMAP
regions"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
arm/arm64: smccc-1.1: Handle function result as parameters
arm/arm64: smccc-1.1: Make return values unsigned long
Documentation/arm64/sve: Couple of improvements and typos
Joerg Roedel [Fri, 31 Aug 2018 08:05:38 +0000 (10:05 +0200)]
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
When PTI is enabled on x86-32 the kernel uses the GDT mapped in the fixmap
for the simple reason that this address is also mapped for user-space.
The efi_call_phys_prolog()/efi_call_phys_epilog() wrappers change the GDT
to call EFI runtime services and switch back to the kernel GDT when they
return. But the switch-back uses the writable GDT, not the fixmap GDT.
When that happened and and the CPU returns to user-space it switches to the
user %cr3 and tries to restore user segment registers. This fails because
the writable GDT is not mapped in the user page-table, and without a GDT
the fault handlers also can't be launched. The result is a triple fault and
reboot of the machine.
Fix that by restoring the GDT back to the fixmap GDT which is also mapped
in the user page-table.
Linus Torvalds [Fri, 31 Aug 2018 15:45:16 +0000 (08:45 -0700)]
Merge tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- minor cleanup avoiding a warning when building with new gcc
- a patch to add a new sysfs node for Xen frontend/backend drivers to
make it easier to obtain the state of a pv device
- two fixes for 32-bit pv-guests to avoid intermediate L1TF vulnerable
PTEs
* tag 'for-linus-4.19b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: remove redundant variable save_pud
xen: export device state to sysfs
x86/pae: use 64 bit atomic xchg function in native_ptep_get_and_clear
x86/xen: don't write ptes directly in 32-bit PV guests
Linus Torvalds [Fri, 31 Aug 2018 15:38:53 +0000 (08:38 -0700)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- regression fixes for i801 and designware
- better API and leak fix for releasing DMA safe buffers
- better greppable strings for the bitbang algorithm
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix leak when using DMA bounce buffer
i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
i2c: refactor function to release a DMA safe buffer
i2c: algos: bit: make the error messages grepable
i2c: designware: Re-init controllers with pm_disabled set on resume
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Andy Lutomirski [Wed, 29 Aug 2018 15:47:18 +0000 (08:47 -0700)]
x86/nmi: Fix NMI uaccess race against CR3 switching
A NMI can hit in the middle of context switching or in the middle of
switch_mm_irqs_off(). In either case, CR3 might not match current->mm,
which could cause copy_from_user_nmi() and friends to read the wrong
memory.
Fix it by adding a new nmi_uaccess_okay() helper and checking it in
copy_from_user_nmi() and in __copy_from_user_nmi()'s callers.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Rik van Riel <riel@surriel.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Jann Horn <jannh@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/dd956eba16646fd0b15c3c0741269dfd84452dac.1535557289.git.luto@kernel.org
Ben Hutchings [Wed, 29 Aug 2018 19:43:17 +0000 (20:43 +0100)]
x86: Allow generating user-space headers without a compiler
When bootstrapping an architecture, it's usual to generate the kernel's
user-space headers (make headers_install) before building a compiler. Move
the compiler check (for asm goto support) to the archprepare target so that
it is only done when building code for the target.
Fixes: e501ce957a78 ("x86: Force asm-goto") Reported-by: Helmut Grohne <helmutg@debian.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180829194317.GA4765@decadent.org.uk
Jann Horn [Tue, 28 Aug 2018 15:49:01 +0000 (17:49 +0200)]
x86/dumpstack: Don't dump kernel memory based on usermode RIP
show_opcodes() is used both for dumping kernel instructions and for dumping
user instructions. If userspace causes #PF by jumping to a kernel address,
show_opcodes() can be reached with regs->ip controlled by the user,
pointing to kernel code. Make sure that userspace can't trick us into
dumping kernel memory into dmesg.
Fixes: 7cccf0725cf7 ("x86/dumpstack: Add a show_ip() function") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: security@kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180828154901.112726-1-jannh@google.com
Rob Herring [Tue, 28 Aug 2018 20:10:48 +0000 (15:10 -0500)]
of: Add device_type access helper functions
In preparation to remove direct access to device_node.type, add
of_node_is_type() and of_node_get_device_type() helpers to check and
retrieve the device type.
Cc: Frank Rowand <frowand.list@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
Mukesh Ojha [Tue, 28 Aug 2018 06:54:54 +0000 (12:24 +0530)]
cpu/hotplug: Remove skip_onerr field from cpuhp_step structure
When notifiers were there, `skip_onerr` was used to avoid calling
particular step startup/teardown callbacks in the CPU up/down rollback
path, which made the hotplug asymmetric.
As notifiers are gone now after the full state machine conversion, the
`skip_onerr` field is no longer required.
James Morse [Thu, 30 Aug 2018 15:05:32 +0000 (16:05 +0100)]
arm64: mm: always enable CONFIG_HOLES_IN_ZONE
Commit 6d526ee26ccd ("arm64: mm: enable CONFIG_HOLES_IN_ZONE for NUMA")
only enabled HOLES_IN_ZONE for NUMA systems because the NUMA code was
choking on the missing zone for nomap pages. This problem doesn't just
apply to NUMA systems.
If the architecture doesn't set HAVE_ARCH_PFN_VALID, pfn_valid() will
return true if the pfn is part of a valid sparsemem section.
When working with multiple pages, the mm code uses pfn_valid_within()
to test each page it uses within the sparsemem section is valid. On
most systems memory comes in MAX_ORDER_NR_PAGES chunks which all
have valid/initialised struct pages. In this case pfn_valid_within()
is optimised out.
Systems where this isn't true (e.g. due to nomap) should set
HOLES_IN_ZONE and provide HAVE_ARCH_PFN_VALID so that mm tests each
page as it works with it.
Currently non-NUMA arm64 systems can't enable HOLES_IN_ZONE, leading to
a VM_BUG_ON():
Linus Torvalds [Fri, 31 Aug 2018 04:18:05 +0000 (21:18 -0700)]
Merge tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull:
- Mediatek has a bunch of fixes to their RDMA and Overlay engines.
- i915 has some Cannonlake/Geminilake watermark workarounds, LSPCON
fix, HDCP free fix, audio fix and a ppgtt reference counting fix.
- amdgpu has some SRIOV, Kasan, memory leaks and other misc fixes"
* tag 'drm-fixes-2018-08-31' of git://anongit.freedesktop.org/drm/drm: (35 commits)
drm/i915/audio: Hook up component bindings even if displays are disabled
drm/i915: Increase LSPCON timeout
drm/i915: Stop holding a ref to the ppgtt from each vma
drm/i915: Free write_buf that we allocated with kzalloc.
drm/i915: Fix glk/cnl display w/a #1175
drm/amdgpu: Need to set moved to true when evict bo
drm/amdgpu: Remove duplicated power source update
drm/amd/display: Fix memory leak caused by missed dc_sink_release
drm/amdgpu: fix holding mn_lock while allocating memory
drm/amdgpu: Power on uvd block when hw_fini
drm/amdgpu: Update power state at the end of smu hw_init.
drm/amdgpu: Fix vce initialize failed on Kaveri/Mullins
drm/amdgpu: Enable/disable gfx PG feature in rlc safe mode
drm/amdgpu: Adjust the VM size based on system memory size v2
drm/mediatek: fix connection from RDMA2 to DSI1
drm/mediatek: update some variable name from ovl to comp
drm/mediatek: use layer_nr function to get layer number to init plane
drm/mediatek: add function to return RDMA layer number
drm/mediatek: add function to return OVL layer number
drm/mediatek: add function to get layer number for component
...
Linus Torvalds [Fri, 31 Aug 2018 01:02:02 +0000 (18:02 -0700)]
Merge tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address a corner case in the menu cpuidle governor and fix error
handling in the PM core's generic clock management code.
Specifics:
- Make the menu cpuidle governor avoid stopping the scheduler tick if
the predicted idle duration exceeds the tick period length, but the
selected idle state is shallow and deeper idle states with high
target residencies are available (Rafael Wysocki).
- Make the PM core's generic clock management code use a proper data
type for one variable to make error handling work (Dan Carpenter)"
* tag 'pm-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: menu: Retain tick when shallow state is selected
PM / clk: signedness bug in of_pm_clk_add_clks()
Akshu Agrawal [Tue, 21 Aug 2018 06:51:57 +0000 (12:21 +0530)]
clk: x86: Set default parent to 48Mhz
System clk provided in ST soc can be set to:
48Mhz, non-spread
25Mhz, spread
To get accurate rate, we need it to set it at non-spread
option which is 48Mhz.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Fixes: 421bf6a1f061 ("clk: x86: Add ST oscout platform clock") Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Wolfram Sang [Fri, 24 Aug 2018 14:52:46 +0000 (16:52 +0200)]
i2c: sh_mobile: fix leak when using DMA bounce buffer
We only freed the bounce buffer after successful DMA, missing the cases
where DMA setup may have gone wrong. Use a better location which always
gets called after each message and use 'stop_after_dma' as a flag for a
successful transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Fri, 24 Aug 2018 14:52:45 +0000 (16:52 +0200)]
i2c: sh_mobile: define start_ch() void as it only returns 0 anyhow
After various refactoring over the years, start_ch() doesn't return
errno anymore, so make the function return void. This saves the error
handling when calling it which in turn eases cleanup of resources of a
future patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Fri, 24 Aug 2018 14:52:44 +0000 (16:52 +0200)]
i2c: refactor function to release a DMA safe buffer
a) rename to 'put' instead of 'release' to match 'get' when obtaining
the buffer
b) change the argument order to have the buffer as first argument
c) add a new argument telling the function if the message was
transferred. This allows the function to be used also in cases
where setting up DMA failed, so the buffer needs to be freed without
syncing to the message buffer.
Also convert the only user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Hans de Goede [Wed, 29 Aug 2018 13:06:31 +0000 (15:06 +0200)]
i2c: designware: Re-init controllers with pm_disabled set on resume
On Bay Trail and Cherry Trail devices we set the pm_disabled flag for I2C
busses which the OS shares with the PUNIT as these need special handling.
Until now we called dev_pm_syscore_device(dev, true) for I2C controllers
with this flag set to keep these I2C controllers always on.
After commit 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and
resume from hibernation"), this no longer works. This commit modifies
lpss_iosf_exit_d3_state() to only run if lpss_iosf_enter_d3_state() has ran
before it, so that it does not run on a resume from hibernate (or from S3).
On these systems the conditions for lpss_iosf_enter_d3_state() to run
never become true, so lpss_iosf_exit_d3_state() never gets called and
the 2 LPSS DMA controllers never get forced into D0 mode, instead they
are left in their default automatic power-on when needed mode.
The not forcing of D0 mode for the DMA controllers enables these systems
to properly enter S0ix modes, which is a good thing.
But after entering S0ix modes the I2C controller connected to the PMIC
no longer works, leading to e.g. broken battery monitoring.
The _PS3 method for this I2C controller looks like this:
Method (_PS3, 0, NotSerialized) // _PS3: Power State 3
{
If ((((PMID == 0x04) || (PMID == 0x05)) || (PMID == 0x06)))
{
Return (Zero)
}
Where PMID = 0x05, so we enter the Return (Zero) path on these systems.
So even if we were to not call dev_pm_syscore_device(dev, true) the
I2C controller will be left in D0 rather then be switched to D3.
Yet on other Bay and Cherry Trail devices S0ix is not entered unless *all*
I2C controllers are in D3 mode. This combined with the I2C controller no
longer working now that we reach S0ix states on these systems leads to me
believing that the PUNIT itself puts the I2C controller in D3 when all
other conditions for entering S0ix states are true.
Since now the I2C controller is put in D3 over a suspend/resume we must
re-initialize it afterwards and that does indeed fix it no longer working.
This commit implements this fix by:
1) Making the suspend_late callback a no-op if pm_disabled is set and
making the resume_early callback skip the clock re-enable (since it now was
not disabled) while still doing the necessary I2C controller re-init.
2) Removing the dev_pm_syscore_device(dev, true) call, so that the suspend
and resume callbacks are actually called. Normally this would cause the
ACPI pm code to call _PS3 putting the I2C controller in D3, wreaking havoc
since it is shared with the PUNIT, but in this special case the _PS3 method
is a no-op so we can safely allow a "fake" suspend / resume.
Fixes: 12864ff8545f ("ACPI / LPSS: Avoid PM quirks on suspend and resume ...") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200861 Cc: 4.15+ <stable@vger.kernel.org> # 4.15+ Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Mika Westerberg [Thu, 30 Aug 2018 08:50:13 +0000 (11:50 +0300)]
i2c: i801: Allow ACPI AML access I/O ports not reserved for SMBus
Commit 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict
with PCI BAR") made it possible for AML code to access SMBus I/O ports
by installing custom SystemIO OpRegion handler and blocking i80i driver
access upon first AML read/write to this OpRegion.
However, while ThinkPad T560 does have SystemIO OpRegion declared under
the SMBus device, it does not access any of the SMBus registers:
Problem with the current approach is that it blocks all I/O port access
and because this system has touchpad connected to the SMBus controller
after first AML access (happens during suspend/resume cycle) the
touchpad fails to work anymore.
Fix this so that we allow ACPI AML I/O port access if it does not touch
the region reserved for the SMBus.
Fixes: 7ae81952cda ("i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR") Link: https://bugzilla.kernel.org/show_bug.cgi?id=200737 Reported-by: Yussuf Khalil <dev@pp3345.net> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Jean Delvare <jdelvare@suse.de> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
* tag 'for-linus-20180830' of git://git.kernel.dk/linux-block:
cdrom: Fix info leak/OOB read in cdrom_ioctl_drive_status
nvmet: free workqueue object if module init fails
nvme-fcloop: Fix dropped LS's to removed target port
nvme-pci: add a memory barrier to nvme_dbbuf_update_and_check_event
block: bsg: move atomic_t ref_count variable to refcount API
block: remove unnecessary condition check
ata: ftide010: Add a quirk for SQ201
blk-wbt: remove dead code
blk-wbt: improve waking of tasks
blk-wbt: abstract out end IO completion handler
xen/blkback: remove unused pers_gnts_lock from struct xen_blkif_ring
xen/blkback: move persistent grants flags to bool
xen/blkfront: reorder tests in xlblk_init()
xen/blkfront: cleanup stale persistent grants
xen/blkback: don't keep persistent grants too long
Linus Torvalds [Thu, 30 Aug 2018 17:05:12 +0000 (10:05 -0700)]
Merge tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtd
Pull mtd fixes from Boris Brezillon:
"Raw NAND fixes:
- denali: Fix a regression caused by the nand_scan() rework
- docg4: Fix a build error when gcc decides to not iniline some
functions (can be reproduced with gcc 4.1.2):
* tag 'mtd/for-4.19-rc2' of git://git.infradead.org/linux-mtd:
mtd: rawnand: denali: do not pass zero maxchips to nand_scan()
mtd: rawnand: docg4: Remove wrong __init annotations
Masahiro Yamada [Mon, 27 Aug 2018 03:39:43 +0000 (12:39 +0900)]
objtool: Remove workaround for unreachable warnings from old GCC
Commit cafa0010cd51 ("Raise the minimum required gcc version to 4.6")
bumped the minimum GCC version to 4.6 for all architectures.
This effectively reverts commit da541b20021c ("objtool: Skip unreachable
warnings for GCC 4.4 and older"), which was a workaround for GCC 4.4 or
older.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: linux-kbuild@vger.kernel.org Link: https://lkml.kernel.org/r/1535341183-19994-1-git-send-email-yamada.masahiro@socionext.com
watchdog: Mark watchdog touch functions as notrace
Some architectures need to use stop_machine() to patch functions for
ftrace, and the assumption is that the stopped CPUs do not make function
calls to traceable functions when they are in the stopped state.
Commit ce4f06dcbb5d ("stop_machine: Touch_nmi_watchdog() after
MULTI_STOP_PREPARE") added calls to the watchdog touch functions from
the stopped CPUs and those functions lack notrace annotations. This
leads to crashes when enabling/disabling ftrace on ARM kernels built
with the Thumb-2 instruction set.
Fix it by adding the necessary notrace annotations.
Fixes: ce4f06dcbb5d ("stop_machine: Touch_nmi_watchdog() after MULTI_STOP_PREPARE") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: oleg@redhat.com Cc: tj@kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180821152507.18313-1-vincent.whitchurch@axis.com
Jann Horn [Tue, 28 Aug 2018 18:40:33 +0000 (20:40 +0200)]
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
Reset the KASAN shadow state of the task stack before rewinding RSP.
Without this, a kernel oops will leave parts of the stack poisoned, and
code running under do_exit() can trip over such poisoned regions and cause
nonsensical false-positive KASAN reports about stack-out-of-bounds bugs.
This does not wipe the exception stacks; if an oops happens on an exception
stack, it might result in random KASAN false-positives from other tasks
afterwards. This is probably relatively uninteresting, since if the kernel
oopses on an exception stack, there are most likely bigger things to worry
about. It'd be more interesting if vmapped stacks and KASAN were
compatible, since then handle_stack_overflow() would oops from exception
stack context.
Fixes: 2deb4be28077 ("x86/dumpstack: When OOPSing, rewind the stack before do_exit()") Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Alexander Potapenko <glider@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: kasan-dev@googlegroups.com Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180828184033.93712-1-jannh@google.com
Linus Torvalds [Thu, 30 Aug 2018 01:41:48 +0000 (18:41 -0700)]
Merge tag 'riscv-for-linus-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux
Pull RISC-V fixes from Palmer Dabbelt:
"RISC-V Fixes and Cleanups for 4.19-rc2
This contains a handful of patches that filtered their way in during
the merge window but just didn't make the deadline. It includes:
- Additional documentation in the riscv,cpu-intc device tree binding
that resulted from some feedback I missed in the original patch
set.
- A build fix that provides the definition of tlb_flush() before
including tlb.h, which fixes a RISC-V build regression introduced
during this merge window.
- A cosmetic cleanup to sys_riscv_flush_icache()"
* tag 'riscv-for-linus-4.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
RISC-V: Use a less ugly workaround for unused variable warnings
riscv: tlb: Provide definition of tlb_flush() before including tlb.h
dt-bindings: riscv,cpu-intc: Cleanups from a missed review
Dave Airlie [Thu, 30 Aug 2018 01:34:55 +0000 (11:34 +1000)]
Merge tag 'drm-intel-fixes-2018-08-29' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- fix for GLK and CNL watermark workaround
- fix for display affecting NUCs with LSPCON
- freeing an allocated write_buf on hdcp
- audio hook when display is disabled
- vma stop holding ppgtt reference
Dave Airlie [Thu, 30 Aug 2018 01:30:02 +0000 (11:30 +1000)]
Merge branch 'drm-fixes-4.19' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
Fixes for 4.19:
- SR-IOV fixes
- Kasan and page fault fix on device removal
- S3 stability fix for CZ/ST
- VCE regression fixes for CIK parts
- Avoid holding the mn_lock when allocating memory
- DC memory leak fix
- BO eviction fix
projects / linux.git / log