Nicholas Piggin [Fri, 1 Jun 2018 10:01:18 +0000 (20:01 +1000)]
powerpc/64s/radix: prefetch user address in update_mmu_cache
Prefetch the faulting address in update_mmu_cache to give the page
table walker perhaps 100 cycles head start as locks are dropped and
the interrupt completed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:17 +0000 (20:01 +1000)]
powerpc/64s/radix: make ptep_get_and_clear_full non-atomic for the full case
This matches other architectures, when we know there will be no
further accesses to the address (e.g., for teardown), page table
entries can be cleared non-atomically.
The comments about NMMU are bogus: all MMU notifiers (including NMMU)
are released at this point, with their TLBs flushed. An NMMU access at
this point would be a bug.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 1 Jun 2018 10:01:16 +0000 (20:01 +1000)]
powerpc/64s/radix: do not flush TLB on spurious fault
In the case of a spurious fault (which can happen due to a race with
another thread that changes the page table), the default Linux mm code
calls flush_tlb_page for that address. This is not required because
the pte will be re-fetched. Hash does not wire this up to a hardware
TLB flush for this reason. This patch avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Refer- ence or Change bit to
1 or to add access authorities, a simpler sequence suffices
because the translation hardware will refetch the PTE if an access
is attempted for which the only problems were reference and/or
change bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 0.95M to 0.90M.
Nicholas Piggin [Fri, 1 Jun 2018 10:01:15 +0000 (20:01 +1000)]
powerpc/64s/radix: do not flush TLB when relaxing access
Radix flushes the TLB when updating ptes to increase permissiveness
of protection (increase access authority). Book3S does not require
TLB flushing in this case, and it is not done on hash. This patch
avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Reference or Change bit to 1
or to add access authorities, a simpler sequence suffices because
the translation hardware will refetch the PTE if an access is
attempted for which the only problems were reference and/or change
bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 1.28M to 0.95M,
tlbiels from 20.17M 19.68M.
powerpc/mm/radix: Change pte relax sequence to handle nest MMU hang
When relaxing access (read -> read_write update), pte needs to be marked invalid
to handle a nest MMU bug. We also need to do a tlb flush after the pte is
marked invalid before updating the pte with new access bits.
We also move tlb flush to platform specific __ptep_set_access_flags. This will
help us to gerid of unnecessary tlb flush on BOOK3S 64 later. We don't do that
in this patch. This also helps in avoiding multiple tlbies with coprocessor
attached.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/radix: Move function from radix.h to pgtable-radix.c
In later patch we will update them which require them to be moved
to pgtable-radix.c. Keeping the function in radix.h results in
compile warning as below.
./arch/powerpc/include/asm/book3s/64/radix.h: In function ‘radix__ptep_set_access_flags’:
./arch/powerpc/include/asm/book3s/64/radix.h:196:28: error: dereferencing pointer to incomplete type ‘struct vm_area_struct’
struct mm_struct *mm = vma->vm_mm;
^~
./arch/powerpc/include/asm/book3s/64/radix.h:204:6: error: implicit declaration of function ‘atomic_read’; did you mean ‘__atomic_load’? [-Werror=implicit-function-declaration]
atomic_read(&mm->context.copros) > 0) {
^~~~~~~~~~~
__atomic_load
./arch/powerpc/include/asm/book3s/64/radix.h:204:21: error: dereferencing pointer to incomplete type ‘struct mm_struct’
atomic_read(&mm->context.copros) > 0) {
Instead of fixing header dependencies, we move the function to pgtable-radix.c
Also the function is now large to be a static inline . Doing the
move in separate patch helps in review.
No functional change in this patch. Only code movement.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/mm/hugetlb: Update huge_ptep_set_access_flags to call __ptep_set_access_flags directly
In a later patch, we want to update __ptep_set_access_flags take page size
arg. This makes ptep_set_access_flags only work with mmu_virtual_psize.
To simplify the code make huge_ptep_set_access_flags directly call
__ptep_set_access_flags so that we can compute the hugetlb page size in
hugetlb function.
Now that ptep_set_access_flags won't be called for hugetlb remove
the is_vm_hugetlb_page() check and add the assert of pte lock
unconditionally.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:13:01 +0000 (16:13 +1000)]
ocxl: Expose the thread_id needed for wait on POWER9
In order to successfully issue as_notify, an AFU needs to know the TID
to notify, which in turn means that this information should be
available in userspace so it can be communicated to the AFU.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Alastair D'Silva [Fri, 11 May 2018 06:12:59 +0000 (16:12 +1000)]
powerpc: use task_pid_nr() for TID allocation
The current implementation of TID allocation, using a global IDR, may
result in an errant process starving the system of available TIDs.
Instead, use task_pid_nr(), as mentioned by the original author. The
scenario described which prevented it's use is not applicable, as
set_thread_tidr can only be called after the task struct has been
populated.
In the unlikely event that 2 threads share the TID and are waiting,
all potential outcomes have been determined safe.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org> Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 17:20:05 +0000 (03:20 +1000)]
powerpc/powernv: process all OPAL event interrupts with kopald
Using irq_work for processing OPAL event interrupts is not necessary.
irq_work is typically used to schedule work from NMI context, a
softirq may be more appropriate. However OPAL events are not
particularly performance or latency critical, so they can all be
invoked by kopald.
This patch removes the irq_work queueing, and instead wakes up
kopald when there is an event to be processed. kopald processes
interrupts individually, enabling irqs and calling cond_resched
between each one to minimise latencies.
Event handlers themselves should still use threaded handlers,
workqueues, etc. as necessary to avoid high interrupts-off latencies
within any single interrupt.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 12:21:48 +0000 (22:21 +1000)]
powerpc/powernv: call OPAL_QUIESCE before OPAL_SIGNAL_SYSTEM_RESET
Although it is often possible to recover a CPU that was interrupted
from OPAL with a system reset NMI, it's undesirable to interrupt them
for a few reasons. Firstly because dump/debug code itself needs to
call firmware, so it could hang on a lock or possibly corrupt a
per-cpu data structure if it or another CPU was interrupted from
OPAL. Secondly, the kexec crash dump code will not return from
interrupt to unwind the OPAL call.
Call OPAL_QUIESCE with QUIESCE_HOLD before sending an NMI IPI to
another CPU, which wait for it to leave firmware (or time out) to
avoid this problem in normal conditions. Firmware bugs may still
result in a timeout and interrupting OPAL, but that is the best
option (stops the CPU, and possibly allows firmware to be debugged).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 01:04:24 +0000 (11:04 +1000)]
powerpc/64: change softe to irqmask in show_regs and xmon
When the soft enabled flag was changed to a soft disable mask, xmon
and register dump code was not updated to reflect that, which is
confusing ('SOFTE: 1' previously meant interrupts were soft enabled,
currently it means the opposite, the general interrupt type has been
disabled).
Fix this by using the name irqmask, and printing it in hex.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Thu, 10 May 2018 01:04:23 +0000 (11:04 +1000)]
powerpc/pmu/fsl: fix is_nmi test for irq mask change
When soft enabled was changed to irq disabled mask, this test missed
being converted (although the equivalent book3s test was converted).
The PMU drivers consider it an NMI when they take a PMI while general
interrupts are disabled. This change restores that behaviour.
Fixes: 01417c6cc7 ("powerpc/64: Change soft_enabled from flag to bitmask") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These are not local timer interrupts but IPIs. It's good to be able
to see how timer offloading is behaving, so split these out into
their own category.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 4 May 2018 17:19:32 +0000 (03:19 +1000)]
powerpc: allow soft-NMI watchdog to cover timer interrupts with large decrementers
Large decrementers (e.g., POWER9) can take a very long time to wrap,
so when the timer iterrupt handler sets the decrementer to max so as
to avoid taking another decrementer interrupt when hard enabling
interrupts before running timers, it effectively disables the soft
NMI coverage for timer interrupts.
Fix this by using the traditional 31-bit value instead, which wraps
after a few seconds. masked interrupt code does the same thing, and
in normal operation neither of these paths would ever wrap even the
31 bit value.
Note: the SMP watchdog should catch timer interrupt lockups, but it
is preferable for the local soft-NMI to catch them, mainly to avoid
the IPI.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The broadcast tick recipient can call tick_receive_broadcast rather
than re-running the full timer interrupt.
It does not have to check for the next event time, because the sender
already determined the timer has expired. It does not have to test
irq_work_pending, because that's a direct decrementer interrupt and
does not go through the clock events subsystem. And it does not have
to read PURR because that was removed with the previous patch.
This results in no code size change, but both the decrementer and
broadcast path lengths are reduced.
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 4 May 2018 17:19:30 +0000 (03:19 +1000)]
powerpc/pseries: lparcfg calculate PURR on demand
For SPLPAR, lparcfg provides a sum of PURR registers for all CPUs.
Currently this is done by reading PURR in context switch and timer
interrupt, and storing that into a per-CPU variable. These are summed
to provide the value.
This does not work with all timer schemes (e.g., NO_HZ_FULL), and it
is sub-optimal for performance because it reads the PURR register on
every context switch, although that's been difficult to distinguish
from noise in the contxt_switch microbenchmark.
This patch implements the sum by calling a function on each CPU, to
read and add PURR values of each CPU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 4 May 2018 17:19:28 +0000 (03:19 +1000)]
powerpc/64s: micro-optimise __hard_irq_enable() for mtmsrd L=1 support
Book3S minimum supported ISA version now requires mtmsrd L=1. This
instruction does not require bits other than RI and EE to be supplied,
so __hard_irq_enable() and __hard_irq_disable() does not have to read
the kernel_msr from paca.
Interrupt entry code already relies on L=1 support.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Fri, 4 May 2018 17:19:25 +0000 (03:19 +1000)]
powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled
irq_work_raise should not cause a decrementer exception unless it is
called from NMI context. Doing so often just results in an immediate
masked decrementer interrupt:
The soft_nmi_interrupt here is the call into the watchdog, due to the
decrementer interrupt firing with irqs soft-disabled. This is
harmless, but sub-optimal.
When it's not called from NMI context or with interrupts enabled, mark
the decrementer pending in the irq_happened mask directly, rather than
having the masked decrementer interupt handler do it. This will be
replayed at the next local_irq_enable. See the comment for details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/powernv/ioda2: Remove redundant free of TCE pages
When IODA2 creates a PE, it creates an IOMMU table with it_ops::free
set to pnv_ioda2_table_free() which calls pnv_pci_ioda2_table_free_pages().
Since iommu_tce_table_put() calls it_ops::free when the last reference
to the table is released, explicit call to pnv_pci_ioda2_table_free_pages()
is not needed so let's remove it.
This should fix double free in the case of PCI hotuplug as
pnv_pci_ioda2_table_free_pages() does not reset neither
iommu_table::it_base nor ::it_size.
This was not exposed by SRIOV as it uses different code path via
pnv_pcibios_sriov_disable().
IODA1 does not inialize it_ops::free so it does not have this issue.
Christophe Leroy [Tue, 29 May 2018 16:06:41 +0000 (16:06 +0000)]
powerpc: Fix build by disabling attribute-alias warning for SYSCALL_DEFINEx
GCC 8.1 emits warnings such as the following. As arch/powerpc code is
built with -Werror, this breaks the build with GCC 8.1.
In file included from arch/powerpc/kernel/pci_64.c:23:
./include/linux/syscalls.h:233:18: error: 'sys_pciconfig_iobase' alias
between functions of incompatible types 'long int(long int, long
unsigned int, long unsigned int)' and 'long int(long int, long int,
long int)' [-Werror=attribute-alias]
asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
^~~
./include/linux/syscalls.h:222:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
This patch inhibits those warnings.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Trim change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch/powerpc/platforms/ps3/repository.c:106:2: error: 'strncpy'
output truncated before terminating nul copying 8 bytes from a
string of the same length [-Werror=stringop-truncation]
strncpy((char *)&n, text, 8);
Fix it by using memcpy(). To make that safe we need to ensure the
destination is pre-zeroed. Use kzalloc() in the nvram code and
initialise the u64 to zero in the ps3 code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Use kzalloc() in the nvram code, flesh out change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a branch with a mixture of mm, x86 and powerpc commits all
relating to some minor cross-arch pkeys consolidation. The x86/mm
changes have been reviewed by Ingo & Dave Hansen and the tree has been
in linux-next for some weeks without issue.
We ended up with an ugly conflict between fixes and next in ftrace.h
involving multiple nested ifdefs, and the automatic resolution is
wrong. So merge fixes into next so we can fix it up.
powerpc/prom: Fix %u/%llx usage since prom_printf() change
In commit eae5f709a4d7 ("powerpc: Add __printf verification to
prom_printf") __printf attribute was added to prom_printf(), which
means GCC started warning about type/format mismatches. As part of
that commit we changed some "%lx" formats to "%llx" where the type is
actually unsigned long long.
Unfortunately prom_printf() doesn't know how to print "%llx", it just
prints a literal "lx", eg:
reserved memory map:
lx - lx
lx - lx
prom_printf() also doesn't know how to print "%u" (only "%lu"), it
just prints a literal "u", eg:
Max number of cores passed to firmware: u (NR_CPUS = 2048)
Instead of:
Max number of cores passed to firmware: 2048 (NR_CPUS = 2048)
This commit adds support for the missing formatters.
Fixes: eae5f709a4d7 ("powerpc: Add __printf verification to prom_printf") Reported-by: Michael Ellerman <mpe@ellerman.id.au> Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Mathieu Malaterre <malat@debian.org> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
cxl: Configure PSL to not use APC virtual machines
APC virtual machines arent used on POWER-9 chips and are already
disabled in on-chip CAPP. They also need to be disabled on the PSL via
'PSL Data Send Control Register' by setting bit(47). This forces the
PSL to send commands to CAPP with queue.id == 0.
Fixes: 5632874311db ("cxl: Add support for POWER9 DD2") Cc: stable@vger.kernel.org # v4.15+ Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Reviewed-by: Alastair D'Silva <alastair@d-silva.org> Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Vaibhav Jain [Fri, 18 May 2018 09:42:23 +0000 (15:12 +0530)]
cxl: Disable prefault_mode in Radix mode
Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:
Unable to handle kernel paging request for data at address 0x00000080
Faulting instruction address: 0xc00800000bcf3b20
cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
sp: c00000037f003a80
msr: 9000000000009033
dar: 80
dsisr: 40000000
current = 0xc00000037f280000
paca = 0xc0000003ffffe600 softe: 3 irq_happened: 0x01
pid = 3529, comm = afp_no_int
<snip>
cxl_prefault+0xfc/0x248 [cxl]
process_element_entry_psl9+0xd8/0x1a0 [cxl]
cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
native_attach_process+0xc0/0x130 [cxl]
afu_ioctl+0x3f4/0x5e0 [cxl]
do_vfs_ioctl+0xdc/0x890
ksys_ioctl+0x68/0xf0
sys_ioctl+0x40/0xa0
system_call+0x58/0x6c
The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.
Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.
Fixes: f24be42aab37 ("cxl: Add psl9 specific code") Cc: stable@vger.kernel.org # v4.12+ Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com> Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Wed, 30 May 2018 12:19:21 +0000 (22:19 +1000)]
powerpc/kbuild: Use flags variables rather than overriding LD/CC/AS
The powerpc toolchain can compile combinations of 32/64 bit and
big/little endian, so it's convenient to consider, e.g.,
`CC -m64 -mbig-endian`
To be the C compiler for the purpose of invoking it to build target
artifacts. So overriding the CC variable to include these flags works
for this purpose.
Unfortunately that is not compatible with the way the proposed new
Kconfig macro language will work.
After previous patches in this series, these flags can be carefully
passed in using flags instead.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Wed, 30 May 2018 12:19:20 +0000 (22:19 +1000)]
powerpc/kbuild: Remove CROSS32 defines from top level powerpc Makefile
Switch VDSO32 build over to use CROSS32_COMPILE directly, and have
it pass in -m32 after the standard c_flags. This allows endianness
overrides to be removed and the endian and bitness flags moved into
standard flags variables.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Nicholas Piggin [Wed, 30 May 2018 12:19:19 +0000 (22:19 +1000)]
powerpc/kbuild: Set default generic machine type for 32-bit compile
Some 64-bit toolchains uses the wrong ISA variant for compiling 32-bit
kernels, even with -m32. Debian's powerpc64le is one such case, and
that is because it is built with --with-cpu=power8.
So when cross compiling a 32-bit kernel with a 64-bit toolchain, set
-mcpu=powerpc initially, which is the generic 32-bit powerpc machine
type and scheduling model. CPU and platform code can override this
with subsequent -mcpu flags if necessary.
This is not done for 32-bit toolchains otherwise it would override
their defaults, which are presumably set appropriately for the
environment (moreso than a 64-bit cross compiler).
This fixes a lot of build failures due to incompatible assembly when
compiling 32-bit kernel with the Debian powerpc64le 64-bit toolchain.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/livepatch: Fix build error with kprobes disabled.
arch/powerpc/kernel/stacktrace.c: In function ‘save_stack_trace_tsk_reliable’:
arch/powerpc/kernel/stacktrace.c:176:28: error: ‘kretprobe_trampoline’ undeclared
if (ip == (unsigned long)kretprobe_trampoline)
^~~~~~~~~~~~~~~~~~~~
Fixes: df78d3f61480 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Josh Poimboeuf [Fri, 25 May 2018 03:48:34 +0000 (22:48 -0500)]
powerpc/modules: remove unused mod_arch_specific.toc field
The toc field in the mod_arch_specific struct isn't actually used
anywhere, so remove it.
Also the ftrace-specific fields are now common between 32-bit and
64-bit, so simplify the struct definition a bit by moving them out of
the __powerpc64__ #ifdef.
Akshay Adiga [Wed, 16 May 2018 12:02:14 +0000 (17:32 +0530)]
powerpc/powernv/cpuidle: Init all present cpus for deep states
Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.
Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.
Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus") Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/perf: Update raw-event code encoding comment for power8
Comment explanning the raw event code encoding for Power8 was
moved to isa207_common.h file when re-factoring the code to
support power9. But then Power9 pmu branched out due to changes
specific to power9. So move the encoding comment back to power8-pmu.c
Just comment movement and no logic change.
Fixes: 4d3576b20716 ('powerpc/perf: factor out power8 pmu macros and defines') Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/chrp/time: Make some functions static, add missing header include
Add a missing include <platforms/chrp/chrp.h>.
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/time.c:41:13: error: no previous prototype for ‘chrp_time_init’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:66:5: error: no previous prototype for ‘chrp_cmos_clock_read’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:74:6: error: no previous prototype for ‘chrp_cmos_clock_write’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:86:5: error: no previous prototype for ‘chrp_set_rtc_time’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/time.c:130:6: error: no previous prototype for ‘chrp_get_rtc_time’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/kernel/tau_6xx.c:53:6: error: no previous prototype for ‘set_thresholds’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:73:6: error: no previous prototype for ‘TAUupdate’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:208:13: error: no previous prototype for ‘TAU_init_smp’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:220:12: error: no previous prototype for ‘TAU_init’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:126:6: error: no previous prototype for ‘TAUException’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/tau: Synchronize function prototypes and body
Some function prototypes and body for Thermal Assist Units were not in
sync. Update the function definition to match the existing function
declaration found in `setup-common.c`, changing an `int` return type to a
`u32` return type. Move the prototypes to a header file. Fix the following
warnings, treated as error with W=1:
arch/powerpc/kernel/tau_6xx.c:257:5: error: no previous prototype for ‘cpu_temp_both’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:262:5: error: no previous prototype for ‘cpu_temp’ [-Werror=missing-prototypes]
arch/powerpc/kernel/tau_6xx.c:267:5: error: no previous prototype for ‘tau_interrupts’ [-Werror=missing-prototypes]
The function prototypes were declared within a `#ifdef CONFIG_PPC_LITE5200`
block which would prevent them from being visible when compiling
`mpc52xx_pm.c`. Move the prototypes outside of the `#ifdef` block to fix
the following warnings treated as errors with W=1:
arch/powerpc/platforms/52xx/mpc52xx_pm.c:58:5: error: no previous prototype for ‘mpc52xx_pm_prepare’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:113:5: error: no previous prototype for ‘mpc52xx_pm_enter’ [-Werror=missing-prototypes]
arch/powerpc/platforms/52xx/mpc52xx_pm.c:181:6: error: no previous prototype for ‘mpc52xx_pm_finish’ [-Werror=missing-prototypes]
powerpc/powermac: Move pmac_pfunc_base_install prototype to header file
The pmac_pfunc_base_install prototype was declared in powermac/smp.c since
function was used there, move it to pmac_pfunc.h header to be visible in
pfunc_base.c. Fix a warning treated as error with W=1:
arch/powerpc/platforms/powermac/pfunc_base.c:330:12: error: no previous prototype for ‘pmac_pfunc_base_install’ [-Werror=missing-prototypes]
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/pci.c:34:5: error: no previous prototype for ‘gg2_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:61:5: error: no previous prototype for ‘gg2_write_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:97:5: error: no previous prototype for ‘rtas_read_config’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/pci.c:112:5: error: no previous prototype for ‘rtas_write_config’ [-Werror=missing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/chrp/setup: Remove idu_size variable and make some functions static
Remove variable declaration idu_size and associated code since not used.
These functions can all be static, make it so. Fix warnings treated as
errors with W=1:
arch/powerpc/platforms/chrp/setup.c:97:6: error: no previous prototype for ‘chrp_show_cpuinfo’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:302:13: error: no previous prototype for ‘chrp_setup_arch’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:385:16: error: variable ‘idu_size’ set but not used [-Werror=unused-but-set-variable]
arch/powerpc/platforms/chrp/setup.c:526:13: error: no previous prototype for ‘chrp_init_IRQ’ [-Werror=missing-prototypes]
arch/powerpc/platforms/chrp/setup.c:559:1: error: no previous prototype for ‘chrp_init2’ [-Werror=missing-prototypes]
powerpc/mm/radix: Use do/while(0) trick for single statement block
In commit 7a22d6321c3d ("powerpc/mm/radix: Update command line parsing for
disable_radix") an `if` statement was added for a possible empty body
(prom_debug).
Fix the following warning, treated as error with W=1:
arch/powerpc/kernel/prom_init.c:656:46: error: suggest braces around empty body in an ‘if’ statement [-Werror=empty-body]
Suggested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mathieu Malaterre <malat@debian.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/sparse: Fix plain integer as NULL pointer warning
Trivial fix to remove the following sparse warnings:
arch/powerpc/kernel/module_32.c:112:74: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/module_32.c:117:74: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1155:28: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1230:20: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1385:36: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:1752:23: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2084:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2110:32: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2167:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:2183:19: warning: Using plain integer as NULL pointer
drivers/macintosh/via-pmu.c:277:20: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:155:67: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:247:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:249:27: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/setup.c:252:37: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:127:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:148:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:44:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:57:21: warning: Using plain integer as NULL pointer
arch/powerpc/mm/tlb_hash32.c:87:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:160:31: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:167:22: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:274:21: warning: Using plain integer as NULL pointer
arch/powerpc/kernel/btext.c:285:31: warning: Using plain integer as NULL pointer
arch/powerpc/include/asm/hugetlb.h:204:16: warning: Using plain integer as NULL pointer
arch/powerpc/mm/ppc_mmu_32.c:170:21: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:1227:23: warning: Using plain integer as NULL pointer
arch/powerpc/platforms/powermac/pci.c:65:24: warning: Using plain integer as NULL pointer
Also use `--fix` command line option from `script/checkpatch --strict` to
remove the following:
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#72: FILE: arch/powerpc/kernel/btext.c:160:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "!vbase"
#80: FILE: arch/powerpc/kernel/btext.c:167:
+ if (vbase == NULL)
CHECK: Comparison to NULL could be written "!base"
#89: FILE: arch/powerpc/kernel/btext.c:274:
+ if (base == NULL)
CHECK: Comparison to NULL could be written "!dispDeviceBase"
#98: FILE: arch/powerpc/kernel/btext.c:285:
+ if (dispDeviceBase == NULL)
CHECK: Comparison to NULL could be written "strstr"
#117: FILE: arch/powerpc/kernel/module_32.c:117:
+ if (strstr(secstrings + sechdrs[i].sh_name, ".debug") != NULL)
CHECK: Comparison to NULL could be written "!Hash"
#130: FILE: arch/powerpc/mm/ppc_mmu_32.c:170:
+ if (Hash == NULL)
CHECK: Comparison to NULL could be written "Hash"
#143: FILE: arch/powerpc/mm/tlb_hash32.c:44:
+ if (Hash != NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#152: FILE: arch/powerpc/mm/tlb_hash32.c:57:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#161: FILE: arch/powerpc/mm/tlb_hash32.c:87:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#170: FILE: arch/powerpc/mm/tlb_hash32.c:127:
+ if (Hash == NULL) {
CHECK: Comparison to NULL could be written "!Hash"
#179: FILE: arch/powerpc/mm/tlb_hash32.c:148:
+ if (Hash == NULL) {
ERROR: space required after that ';' (ctx:VxV)
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "node"
#192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
+ for (; node != NULL;node = node->sibling) {
CHECK: Comparison to NULL could be written "!region"
#201: FILE: arch/powerpc/platforms/powermac/pci.c:1227:
+ if (region == NULL)
CHECK: Comparison to NULL could be written "of_get_property"
#214: FILE: arch/powerpc/platforms/powermac/setup.c:155:
+ if (of_get_property(np, "cache-unified", NULL) != NULL && dc) {
CHECK: Comparison to NULL could be written "!np"
#223: FILE: arch/powerpc/platforms/powermac/setup.c:247:
+ if (np == NULL)
CHECK: Comparison to NULL could be written "np"
#226: FILE: arch/powerpc/platforms/powermac/setup.c:249:
+ if (np != NULL) {
CHECK: Comparison to NULL could be written "l2cr"
#230: FILE: arch/powerpc/platforms/powermac/setup.c:252:
+ if (l2cr != NULL) {
CHECK: Comparison to NULL could be written "via"
#243: FILE: drivers/macintosh/via-pmu.c:277:
+ if (via != NULL)
CHECK: Comparison to NULL could be written "current_req"
#252: FILE: drivers/macintosh/via-pmu.c:1155:
+ if (current_req != NULL) {
CHECK: Comparison to NULL could be written "!req"
#261: FILE: drivers/macintosh/via-pmu.c:1230:
+ if (req == NULL || pmu_state != idle
CHECK: Comparison to NULL could be written "!req"
#270: FILE: drivers/macintosh/via-pmu.c:1385:
+ if (req == NULL) {
CHECK: Comparison to NULL could be written "!pp"
#288: FILE: drivers/macintosh/via-pmu.c:2084:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#297: FILE: drivers/macintosh/via-pmu.c:2110:
+ if (count < 1 || pp == NULL)
CHECK: Comparison to NULL could be written "!pp"
#306: FILE: drivers/macintosh/via-pmu.c:2167:
+ if (pp == NULL)
CHECK: Comparison to NULL could be written "pp"
#315: FILE: drivers/macintosh/via-pmu.c:2183:
+ if (pp != NULL) {
powerpc/altivec: Add missing prototypes for altivec
Some functions prototypes were missing for the non-altivec code. Add the
missing prototypes in a new header file, fix warnings treated as errors
with W=1:
arch/powerpc/lib/xor_vmx_glue.c:18:6: error: no previous prototype for ‘xor_altivec_2’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:29:6: error: no previous prototype for ‘xor_altivec_3’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:40:6: error: no previous prototype for ‘xor_altivec_4’ [-Werror=missing-prototypes]
arch/powerpc/lib/xor_vmx_glue.c:52:6: error: no previous prototype for ‘xor_altivec_5’ [-Werror=missing-prototypes]
The prototypes were already present in <asm/xor.h> but this header file is
meant to be included after <include/linux/raid/xor.h>. Trying to re-use
<asm/xor.h> directly would lead to warnings such as:
arch/powerpc/include/asm/xor.h:39:15: error: variable ‘xor_block_altivec’ has initializer but incomplete type
Trying to re-use <asm/xor.h> after <include/linux/raid/xor.h> in
xor_vmx_glue.c would in turn trigger the following warnings:
include/asm-generic/xor.h:688:34: error: ‘xor_block_32regs’ defined but not used [-Werror=unused-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):
arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).
This patch fix also the following warnings revealed by checkpatch:
WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
#101: FILE: arch/powerpc/kernel/prom_init.c:1235:
+ prom_debug("alloc_up(%lx, %lx)\n", size, align);
and
WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
#138: FILE: arch/powerpc/kernel/prom_init.c:1278:
+ prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,
Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 21 May 2018 11:28:34 +0000 (21:28 +1000)]
powerpc/xmon: Realign paca dump fields
We've added some fields with longer names since we originally wrote
this, so the fields are no longer lined up. Adjust the widths to make
it all look nice again, eg:
powerpc/xmon: Add __printf annotation to xmon_printf()
This allows the compiler to verify the format strings vs the types of
the arguments.
Update the other prototype declarations in asm/xmon.h.
Silence warnings (triggered at W=1) by adding relevant __printf
attribute. Move #define at bottom of the file to prevent conflict with
gcc attribute.
Solves the original warning:
arch/powerpc/xmon/nonstdio.c:178:2: error: function might be
possible candidate for ‘gnu_printf’ format attribute
In turn this uncovered many formatting errors in xmon.c, all fixed in
this patch.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Always use px not p, fixup the 44x specific code, tweak change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Ellerman [Mon, 21 May 2018 11:06:19 +0000 (21:06 +1000)]
powerpc/xmon: Specify the full format in DUMP() macro
In dump_one_paca() the DUMP macro unconditionally prepends '#' to the
printf format specifier. In most cases we're using either 'x' or 'lx'
etc. and that is OK. But for 'p' and other formats using '#' is
actually undefined, and once we enable printf() checking for
xmon_printf() we will get warnings from the compiler.
So just have each usage specify the full format, that way we can omit
'#' when it's inappropriate.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Mathieu Malaterre <malat@debian.org>
Michal Suchanek [Wed, 23 May 2018 18:00:54 +0000 (20:00 +0200)]
powerpc/xmon: Also setup debugger hooks when single-stepping
When single-stepping kernel code from xmon without a debug hook
enabled the kernel crashes. This can happen when kernel starts with
xmon on crash disabled but xmon is entered using sysrq.
Call force_enable_xmon when single-stepping in xmon to install the
xmon debug hooks.
Fixes: e1368d0c9edb ("powerpc/xmon: Setup debugger hooks when first break-point is set") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Tue, 22 May 2018 06:14:27 +0000 (16:14 +1000)]
selftests/powerpc: Add ptrace hw breakpoint test
This test the ptrace hw breakpoints via PTRACE_SET_DEBUGREG and
PPC_PTRACE_SETHWDEBUG. This test was use to find the bugs fixed by
these recent commits:
4f7c06e26e powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG cd6ef7eebf powerpc/ptrace: Fix enforcement of DAWR constraints
Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Add SPDX tag, clang format it] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Christophe Leroy [Wed, 23 May 2018 08:53:22 +0000 (10:53 +0200)]
powerpc/mm: Only read faulting instruction when necessary in do_page_fault()
Commit a7a9dcd882a67 ("powerpc: Avoid taking a data miss on every
userspace instruction miss") has shown that limiting the read of
faulting instruction to likely cases improves performance.
This patch goes further into this direction by limiting the read
of the faulting instruction to the only cases where it is likely
needed.
On an MPC885, with the same benchmark app as in the commit referred
above, we see a reduction of about 3900 dTLB misses (approx 3%):
Before the patch:
Performance counter stats for './fault 500' (10 runs):
The proper work of the huge stack expansion was tested with the
following app:
int main(int argc, char **argv)
{
char buf[1024 * 1025];
sprintf(buf, "Hello world !\n");
printf(buf);
exit(0);
}
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add include of pagemap.h to fix build errors] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch exports tm_enable()/tm_disable/tm_abort() APIs, which
will be used for PR KVM transactional memory logic.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com> Reviewed-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simon Guo [Wed, 23 May 2018 07:01:45 +0000 (15:01 +0800)]
powerpc/reg: Add TEXASR related macros
This patches add some macros for CR0/TEXASR bits so that PR KVM TM
logic (tbegin./treclaim./tabort.) can make use of them later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com> Reviewed-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simon Guo [Wed, 23 May 2018 07:01:44 +0000 (15:01 +0800)]
powerpc: Export msr_check_and_set() to modules
PR KVM will need to reuse msr_check_and_set().
This patch exports this API for reuse.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com> Reviewed-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
hwmon: (ibmpowernv): Add support to read 64 bit sensors
The firmware has supported for reading sensor values of size u32.
This patch adds support to use newer firmware functions which allows
to read the sensors of size u64.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 17 May 2018 05:37:15 +0000 (15:37 +1000)]
powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG
In commit e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Michael Neuling [Thu, 17 May 2018 05:37:14 +0000 (15:37 +1000)]
powerpc/ptrace: Fix enforcement of DAWR constraints
Back when we first introduced the DAWR, in commit 4ae7ebe9522a
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add byte-swapping versions of __raw_writeq() and __raw_rm_writeq().
This allows us to avoid sparse warnings caused by passing __be64 to
__raw_writeq(), which takes unsigned long:
arch/powerpc/platforms/powernv/pci-ioda.c:1981:38:
warning: incorrect type in argument 1 (different base types)
expected unsigned long [unsigned] v
got restricted __be64 [usertype] <noident>
It's also generally preferable to use a byte-swapping accessor rather
than doing it by hand in the code, which is more bug prone.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Anju T Sudhakar [Wed, 16 May 2018 06:35:18 +0000 (12:05 +0530)]
powerpc/perf: Fix memory allocation for core-imc based on num_possible_cpus()
Currently memory is allocated for core-imc based on cpu_present_mask,
which has bit 'cpu' set iff cpu is populated. We use (cpu number / threads
per core) as the array index to access the memory.
Under some circumstances firmware marks a CPU as GUARDed CPU and boot the
system, until cleared of errors, these CPU's are unavailable for all
subsequent boots. GUARDed CPUs are possible but not present from linux
view, so it blows a hole when we assume the max length of our allocation
is driven by our max present cpus, where as one of the cpus might be online
and be beyond the max present cpus, due to the hole.
So (cpu number / threads per core) value bounds the array index and leads
to memory overflow.
Call trace observed during a guard test:
Faulting instruction address: 0xc000000000149f1c
cpu 0x69: Vector: 380 (Data Access Out of Range) at [c000003fea303420]
pc:c000000000149f1c: prefetch_freepointer+0x14/0x30
lr:c00000000014e0f8: __kmalloc+0x1a8/0x1ac
sp:c000003fea3036a0
msr:9000000000009033
dar:c9c54b2c91dbf6b7
current = 0xc000003fea2c0000
paca = 0xc00000000fddd880 softe: 3 irq_happened: 0x01
pid = 1, comm = swapper/104
Linux version 4.16.7-openpower1 (smc@smc-desktop) (gcc version 6.4.0
(Buildroot 2018.02.1-00006-ga8d1126)) #2 SMP Fri May 4 16:44:54 PDT 2018
enter ? for help
call trace:
__kmalloc+0x1a8/0x1ac
(unreliable)
init_imc_pmu+0x7f4/0xbf0
opal_imc_counters_probe+0x3fc/0x43c
platform_drv_probe+0x48/0x80
driver_probe_device+0x22c/0x308
__driver_attach+0xa0/0xd8
bus_for_each_dev+0x88/0xb4
driver_attach+0x2c/0x40
bus_add_driver+0x1e8/0x228
driver_register+0xd0/0x114
__platform_driver_register+0x50/0x64
opal_imc_driver_init+0x24/0x38
do_one_initcall+0x150/0x15c
kernel_init_freeable+0x250/0x254
kernel_init+0x1c/0x150
ret_from_kernel_thread+0x5c/0xc8
Allocating memory for core-imc based on cpu_possible_mask, which has
bit 'cpu' set iff cpu is populatable, will fix this issue.
Michael Neuling [Fri, 18 May 2018 01:37:42 +0000 (11:37 +1000)]
powerpc/64s: Clear PCR on boot
Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.
We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).
Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: stable@vger.kernel.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Finn Thain [Fri, 18 May 2018 01:18:33 +0000 (11:18 +1000)]
powerpc/lib: Fix "integer constant is too large" build failure
My powerpc-linux-gnu-gcc v4.4.5 compiler can't build a 32-bit kernel
any more:
arch/powerpc/lib/sstep.c: In function 'do_popcnt':
arch/powerpc/lib/sstep.c:1068: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1070: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1079: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c: In function 'do_prty':
arch/powerpc/lib/sstep.c:1117: error: integer constant is too large for 'long' type
This file gets compiled with -std=gnu89 which means a constant can be
given the type 'long' even if it won't fit. Fix the errors with a 'ULL'
suffix on the relevant constants.
Nicholas Piggin [Mon, 14 May 2018 15:59:47 +0000 (01:59 +1000)]
powerpc/powernv: Fix NVRAM sleep in invalid context when crashing
Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.
Nicholas Piggin [Mon, 14 May 2018 15:59:46 +0000 (01:59 +1000)]
powerpc/powernv: Fix opal_event_shutdown() called with interrupts disabled
A kernel crash in process context that calls emergency_restart from
panic will end up calling opal_event_shutdown with interrupts disabled
but not in interrupt. This causes a sleeping function to be called
which gives the following warning with sysrq+c:
Rebooting in 10 seconds..
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
in_atomic(): 0, irqs_disabled(): 1, pid: 7669, name: bash
CPU: 20 PID: 7669 Comm: bash Tainted: G D W 4.17.0-rc5+ #3
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
___might_sleep+0x174/0x1a0
mutex_lock+0x38/0xb0
__free_irq+0x68/0x460
free_irq+0x70/0xc0
opal_event_shutdown+0xb4/0xf0
opal_shutdown+0x24/0xa0
pnv_shutdown+0x28/0x40
machine_shutdown+0x44/0x60
machine_restart+0x28/0x80
emergency_restart+0x30/0x50
panic+0x2a0/0x328
oops_end+0x1ec/0x1f0
bad_page_fault+0xe8/0x154
handle_page_fault+0x34/0x38
--- interrupt: 300 at sysrq_handle_crash+0x44/0x60
LR = __handle_sysrq+0xfc/0x260
flag_spec.62335+0x12b844/0x1e8db4 (unreliable)
__handle_sysrq+0xfc/0x260
write_sysrq_trigger+0xa8/0xb0
proc_reg_write+0xac/0x110
__vfs_write+0x6c/0x240
vfs_write+0xd0/0x240
ksys_write+0x6c/0x110
Fixes: 9f0fd0499d30 ("powerpc/powernv: Add a virtual irqchip for opal events") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
powerpc/32: Use stmw/lmw for registers save/restore in asm
arch/powerpc/Makefile activates -mmultiple on BE PPC32 configs
in order to use multiple word instructions in functions entry/exit.
The patch does the same for the asm parts, for consistency.
On processors like the 8xx on which insn fetching is pretty slow,
this speeds up registers save/restore.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: PPC32 is BE only, so drop the endian checks] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
That commit was pointless, because csum_add() sums two 32 bits
values, so the sum is 0x1fffffffe at the maximum.
And then when adding upper part (1) and lower part (0xfffffffe),
the result is 0xffffffff which doesn't carry.
Any lower value will not carry either.
And behind the fact that this commit is useless, it also kills the
whole purpose of having an arch specific inline csum_add()
because the resulting code gets even worse than what is obtained
with the generic implementation of csum_add()